windham

accent cabinet

style # WNCBNTKDRD (red) dpci # 249-16-0724 tcin # 14395598 style # WNCBNTKDBK (black) dpci # 249-16-0726 tcin # 14395596 style # WNCBNTKDBL (teal) dpci # 249-16-0085 tcin # 15102614 style # WNCBNTKDGY (gray) dpci # 249-16-0084 tcin # 14372259 style # WNCBNTKDWH (shell) dpci # 249-16-0719 tcin # 14372249 style # WNCBNTKDOV (overcast) dpci # 249-16-4305 tcin # 50076625

>> assembly instructions

© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2

Congratulations on your latest Target purchase.

Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.

All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time. Good luck—though we’re confident you won’t need it.

before you begin

1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.

2. Use the carton as a working surface to prevent product damage during assembly.

3. Gather all tools prior to assembly.

tools needed

table of contents

introduction

hardware

parts list

how to use the cam lock system

2

4

5

6 assembly 7-14

how to adjust door alignment 15

QUESTIONS?

Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

3

hardware

(H1) x 8 wooden dowel

(H2) x 4 cam bolt

(H3) x 4 cam

(H4) x 21 short pan head screw

(H5) x 8 short flat head screw

(H6) x 4 shelf support

(H7) x 2 knob

(H8) x 2 knob bolt

(H9) x 1 long flat-head screw

(H10) x 1 magnet

4

(H11) x 1

38mm wall screw

(H12) x 1 wall anchor

(H13) x 1 wall strap

(H14) x 1

15mm truss head screw

(H15) x 2 washer

exploded diagram

ITEM DESCRIPTION QUANTITY

A top panel 1

B left side panel 1

E

F

G

H

C

D right side panel bottom panel shelf panel left door right door back panel

1

1

1

1

1

1

5

how to use the cam lock system

Screw cam bolt into panel Align cam bolt(s) with cross-bored hole(s) and insert all the way until panels are flush

Push cam into panel - arrow feature on cam top points to panel edge

6

Rotate cam(s) clockwise 180° to lock panels together

Panels should be tight against each other and connection should be rigid

step 1: attach right side panel to bottom panel

(H1) x 2 wooden dowel

(H2) x 2 cam bolt

(H3) x 2 cam

1.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out.

1.2. Screw-In cam bolts must be screwed down flush in right side panel.

1.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.

7

step 2: attach left side panel

(H1) x 2 wooden dowel

(H2) x 2 cam bolt

(H3) x 2 cam

8

2.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.

2.2. Screw-In cam bolts must be screwed down flush in left side panel.

2.3. Refer to page 6 for instructions on how to use the cam lock system. Do not over tighten bolts.

step 3: attach top panel

(H4)

(H1) x 4 wooden dowel

(H4) x 2 short pan head screw

(H9) x 4 long flat head screw

(H10) x 1 magnet

3.1. Align short pan head screws with pre-drilled holes to attach magnet to top panel. Do not over tighten screws.

3.2. Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out.

3.3. Align long flat head screws with pre-drilled holes to attach side panels to top panel. Do not over tighten screws.

9

**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**

Hole for anti-tip kit.

pre-drilled holes

Begin by installing all of the screws along one edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square. (If using a tape measure, the distance from one corner, diagonally to the other corner should be the same in both directions.) If not, apply gentle pressure to the diagonally opposite corners to shift case into alignment. Re-measure to ensure equal distances. Install the remaining screws, starting with the corners.

(H4) x 19 short pan head screw

10

4.1. Make sure the short pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.

step 5: attach knobs to doors

(H7) x 2 knob

(H8) x 2 knob bolt

5.1. Align knob bolts with pre-drilled holes to attach knobs to doors. Do not over tighten bolts.

11

step 6: attach doors to cabinet

12

(H5) x 8 short flat head screw

step 7: install adjustable shelves

(H6) x 4 shelf support

7.1. Insert shelf supports into desired hole. Different holes accomodate different shelf heights.

7.2. Angle shelves to fit between the rails and set on top of shelf supports.

13

step 8: install anti-tip kit

(H15)

(H13)

(H14)

Position against wall

Mark position of strap hole on wall

Drill 1/4’’ hole

Tap in wall anchor

(H12)

14

Fasten anti-tip strap with flat-head screw provided

(H14) x 1

15mm truss head screw

(H13) x 1 wall strap

(H15) x 2 washer

(H12) x 1 wall anchor

(H11) x 1

38mm wall screw

(H11)

(H15)

how to adjust door alignment

Tips for proper door alignment:

-Adjustable levelers will reduce minor door mis-alignments

caused by an uneven floor.

-Use a level to determine if the cabinet top is level. If not, start

with the levelers retracted and adjust them as needed.To

retract the levelers turn them counterclockwise. To extend

the levelers turn them clockwise.

-If door mis-alignment persists, refer back to Step 4 (pg. 10)

for additional information. If the cabinet is not square you will

need to repeat this step.

adjustable leg levelers

15

WARNING

Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:

• Install tip-over restraint provided. heaviest items in the lowest drawers.

• Do not set TV's or other heavy objects on top of this product, unless the product is specifically designed to accommodate them.

• Never open more than one drawer at a time.

(OR)

• Do not defeat or remove the drawer interlock system.

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

This is a permanent label. Do not remove.

50 lbs.

inner shelf weight limit is 40 lbs.

16

1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.

2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.

QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling. © 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.