Honda FOURTRAX Owner's Manual 242 Pages
advertisement
08/07/07 14:17:36 32HP4620 0002
Honda TRX420TM/FM
FOURTRAX 420/4 × 4
OWNER’S MANUAL
08/07/07 14:17:45 32HP4620 0003
Introduction
Congratulations on choosing your Honda ATV.
When you own a Honda, you’re part of a worldwide family of satisfied customers − people who appreciate Honda’s reputation for building quality into every product.
Your Honda was designed as a recreational ATV for off-road use by one rider only.
Before riding, take time to get acquainted with your ATV and how it works. To protect your investment, we urge you to take responsibility for keeping your ATV well maintained. Scheduled service is a must, of course. But it’s just as important to observe the break-in guidelines, and perform all pre-ride and other periodic checks detailed in this manual.
We also recommend that you read this owner’s manual before you ride.
It’s full of facts, instructions, safety information, and helpful tips. To make it easy to use, the manual contains a detailed list of topics at the beginning of each section, and both an in-depth table of contents and an index at the back of the book.
As you read this manual, you will find information that is preceded by a symbol. This information is intended to help you avoid damage to your Honda, other property, or the environment.
Whenever you ride, tread lightly. By staying on established trails and riding only in approved areas, you help protect the environment and keep off-road riding areas open for the future.
Introduction
08/07/07 14:17:49 32HP4620 0004
Introduction
If you have any questions, or if you ever need special service or repairs, remember that your Honda dealer knows your ATV best and is dedicated to your complete satisfaction.
Happy riding!
Introduction
08/07/07 14:17:54 32HP4620 0005
A Few Words About Safety
Your safety, and the safety of others, is very important. And operating this ATV safely is an important responsibility.
To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual.
This information alerts you to potential hazards that could hurt you or others.
Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining an ATV. You must use your own good judgment.
You will find important safety information in a variety of forms, including:
Safety Labels –– on the ATV.
Safety Messages –– preceded by a safety alert symbol and one of three signal words: DANGER, WARNING, or CAUTION .
A Few Words About Safety
08/07/07 14:18:02 32HP4620 0006
A Few Words About Safety
These signal words mean:
You WILL be KILLED or
SERIOUSLY HURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be HURT if you don’t follow instructions.
Safety Headings –– such as Important Safety Reminders or Important
Safety Precautions.
Safety Section –– such as ATV Safety.
Instructions –– how to use this ATV correctly and safely.
This entire manual is filled with important safety information –– please read it carefully.
A Few Words About Safety
08/07/07 14:18:12 32HP4620 0007
Contents
These pages give an overview of the contents of your owner’s manual.
The first page of each section lists the topics covered in that section.
ATV Safety .......................................................................................
.
Important safety information you should know, plus a look at the safety related labels on your ATV.
1
Instruments & Controls ...................................................................
.
The location and function of indicators and controls on your ATV and operating instructions for various controls and features.
9
Before Riding ....................................................................................
.
The importance of wearing a helmet and other protective gear, how to make sure you and your ATV are ready to ride, and important information about loading.
37
Basic Operation & Riding ...............................................................
.
How to start and stop the engine, shift gears, and brake. Also, riding
53 precautions.
Contents
08/07/07 14:18:24 32HP4620 0008
Contents
Servicing Your Honda .....................................................................
.
Why your ATV needs regular maintenance, what you need to know
85 before servicing your Honda, an owner maintenance schedule, and instructions for specific maintenance and adjustment items.
Tips ....................................................................................................
.
171
How to store and transport your ATV and how to be an environmentally responsible rider.
Taking Care of the Unexpected ......................................................
.
181
What to do if you have a flat tyre, your engine won’t start, etc.
Technical Information .....................................................................
.
201
ID numbers, technical specifications, and other technical facts.
Table of Contents .............................................................................
.
210
Sequential listing of topics in this owner’s manual.
Index ..................................................................................................
.
216
228
Contents
08/07/07 14:18:26 32HP4620 0009
08/07/07 14:18:31 32HP4620 0010
ATV Safety
This section presents some of the most important information and recommendations to help you ride your ATV safely. Please take a few moments to read these pages. This section also includes information about the location of safety labels on your ATV.
Important Safety Information ...............................................................
.
Safety Labels .........................................................................................
.
2
5
ATV Safety
1
08/07/07 14:18:40 32HP4620 0011
Important Safety Information
Your ATV can provide many years of service and pleasure if you take responsibility for your own safety and understand the challenges you can meet while riding.
There is much that you can do to protect yourself when you ride. You’ll find many helpful recommendations throughout this manual. The following are a few that we consider to be most important.
Follow the Age Recommendation
The minimum recommended age for this ATV model is 16. Children under age 16 should never operate this vehicle.
Always Wear a Helmet
It’s a proven fact: helmets significantly reduce the number and severity of head injuries. So always wear an approved motorcycle helmet. We also recommend that you wear eye protection, sturdy boots, gloves, and other protective gear (page 38 ).
Never Carry a Passenger
Your ATV is designed for one person only. There are no handholds, footrests, or seat for a second person, so never carry a passenger. A passenger could interfere with your ability to move around to maintain your balance and control of the ATV.
2
ATV Safety
08/07/07 14:18:48 32HP4620 0012
Important Safety Information
Ride Off-road Only
Your ATV is designed and manufactured for off-road use only. The tyres are not made for pavement, and the ATV does not have turn signals and other features required for use on public roads. If you need to cross a paved or public road, get off and walk your ATV across.
Take Time to Learn & Practice
Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.
Be Alert for Off-road Hazards
The terrain can present a variety of challenges when you ride off-road.
Continually ‘‘read’’ the terrain for unexpected turns, drop-offs, rocks, ruts, and other hazards. Always keep your speed low enough to allow time to see and react to hazards.
ATV Safety
3
08/07/07 14:18:55 32HP4620 0013
Important Safety Information
Ride within Your Limits
Pushing limits is another major cause of ATV accidents. Never ride beyond your personal abilities or faster than conditions warrant.
Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgments and ride safely.
Don’t Drink and Ride
Alcohol and riding don’t mix. Even one drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. So don’t drink and ride, and don’t let your friends drink and ride either.
Keep Your Honda in Safe Condition
It’s important to keep your ATV properly maintained and in safe riding condition. Having a breakdown can be difficult, especially if you are stranded off-road far from your base. To help avoid problems, inspect your ATV before every ride and perform all recommended maintenance.
4
ATV Safety
08/07/07 14:18:59 32HP4620 0014
Safety Labels
Your ATV comes with several labels containing important safety information. Anyone who rides the vehicle should read and understand this information before riding.
The labels should be considered permanent parts of the vehicle. If a label comes off or becomes hard to read, contact your Honda dealer for replacements.
ATV Safety
5
08/07/07 14:19:08 32HP4620 0015
Safety Labels
(TRX420TM)
(TRX420FM)
Engine net power
Machine mass
Engine net power
Machine mass
6
ATV Safety
08/07/07 14:19:21 32HP4620 0016
Safety Labels
ATV Safety
7
08/07/07 14:19:42 32HP4620 0017
Safety Labels
(TRX420FM only)
8
ATV Safety
08/07/07 14:19:53 32HP4620 0018
Instruments & Controls
This section shows the location of all indicators and controls you would normally use before or while riding your ATV.
The items listed on this page are described in this section. Instructions for other components are presented in other sections of this manual where they will be most useful.
Operation Component Locations ..........................................................
.
11
Indicators & Displays ............................................................................
.
14
Multi-function Display ......................................................................
.
18
Gear Position Indicator ......................................................................
.
19
Oil Change Indicator .........................................................................
.
20
Odometer ...........................................................................................
.
21
Tripmeter ...........................................................................................
.
21
Hourmeter .........................................................................................
.
22
Fuel Gauge ........................................................................................
.
23
(cont’d)
Instruments & Controls
9
08/07/07 14:20:08 32HP4620 0019
Instruments & Controls
Controls & Features ..............................................................................
.
24
Fuel Valve .........................................................................................
.
24
Ignition Switch ..................................................................................
.
25
2WD/4WD Select Lever ( TRX420FM only) ....................................
.
26
Start Button .......................................................................................
.
27
Engine Stop Switch ...........................................................................
.
27
Headlight Switch ...............................................................................
.
28
Headlight Dimmer Switch .................................................................
.
28
Horn Button .......................................................................................
.
28
Recoil Starter .....................................................................................
.
29
Throttle Lever ...................................................................................
.
30
Reverse Selector Knob ......................................................................
.
31
Front Brake Lever .............................................................................
.
32
Rear Brake Lever/Parking Brake Lever ............................................
.
32
Rear Brake Pedal ...............................................................................
.
32
Parking Brake ....................................................................................
.
33
Flag Pole Bracket ..............................................................................
.
34
Trailer Hitch ......................................................................................
.
35
10
Instruments & Controls
08/07/07 14:20:13 32HP4620 0020
Operation Component Locations reverse selector knob parking brake lock lever headlight switch horn button rear brake lever/ parking brake lever front brake lever headlight dimmer switch throttle lever start button ignition switch
2WD/4WD select lever
(TRX420FM only) engine stop switch
Instruments & Controls
11
08/07/07 14:20:18 32HP4620 0021
Operation Component Locations rear cargo rack seat latch front cargo rack recoil starter rear brake pedal fuel valve
12
Instruments & Controls
08/07/07 14:20:23 32HP4620 0022
Operation Component Locations flag pole bracket shift lever trailer hitch
Instruments & Controls
13
08/07/07 14:20:31 32HP4620 0023
Indicators & Displays
The indicators and displays on your ATV keep you informed, alert you to possible problems, and make your riding safer and more enjoyable.
Refer to the indicators frequently. Their functions are described on the following pages.
(1) (2) (3) (4) (5)
(6)
(7)
(1) reverse indicator
(2) neutral indicator
(3) 4WD indicator
(TRX420FM only)
(4) high coolant temperature indicator
(5) PGM-FI indicator
(6) multi-function display
(7) hourmeter/odometer/ tripmeter select button
Lamp Check
The high coolant temperature indicator and PGM-FI indicator come on for a few seconds and then go off when you turn the ignition switch ON
( ).
14
Instruments & Controls
08/07/07 14:20:40 32HP4620 0024
Indicators & Displays
The indicators are identified in the table on page 16 with the words:
Lamp Check.
When applicable, the reverse or neutral indicators come on when you turn the ignition switch ON ( ) and remain on until you shift out of reverse or neutral.
TRX420FM only:
When applicable, the 4WD indicator comes on when you turn the ignition switch ON ( ) and remains on until you shift out of 4WD mode.
If one of these indicators does not come on when it should, have your
Honda dealer check for problems.
Display Check
When the ignition switch is turned ON ( ), the multi-function display make sure the liquid crystal display is functioning properly.
The displays are identified in the table on page 17 with the words:
Display Check.
If any part of these displays does not come on when it should, have your
Honda dealer check for problems.
(1)
(1) multi-function display
Instruments & Controls
15
08/07/07 14:20:52 32HP4620 0025
3
4
1
2
Indicators & Displays
5
Reverse indicator
Neutral indicator
4WD indicator
(TRX420FM only)
High coolant temperature indicator
PGM-FI indicator
Lights when the transmission is in reverse.
Lamp Check.
Lights when the transmission is in neutral.
Lamp Check.
Lights when the 4WD drive mode engages.
Lamp Check .
Lights when coolant temperature is high enough to adversely affect the service life of the engine.
If the high coolant temperature indicator comes on while you are riding, immediately bring the vehicle to a stop, turn the engine off and let it cool. See page 190 .
Lamp Check.
Lights when there is any abnormality in the PGM-FI (Programmed Fuel
Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned
ON ( ). If the indicator comes on at any other time, reduce speed and take your vehicle to a Honda dealer as soon as possible.
Lamp Check.
16
Instruments & Controls
08/07/07 14:21:08 32HP4620 0026
6
7
Multi-function display
Gear position indicator
Oil change indicator
Speedometer
Odometer
Tripmeter
Hourmeter
Hourmeter/ odometer/tripmeter select button
Indicators & Displays
The display includes the following functions.
Display Check.
Shows the gear position (page 19 ).
Lights when specified maintenance interval for engine oil change is reached (page 20 ).
Shows riding speed.
Shows accumulated mileage
(page 21 ).
Shows mileage per trip (page 21 ).
Shows hours and tenths of hours of engine operation (page 22 ).
Selects display of the odometer or tripmeter or hourmeter. Resets the tripmeter to zero (0) (page 21 ). This button also used to reset the oil change indicator (page 20 ).
Instruments & Controls
17
08/07/07 14:21:14 32HP4620 0027
Indicators & Displays
Multi-function Display
Gear position indicator
Oil change indicator
Speedometer
Odometer
Tripmeter
Hourmeter
(3)
(2)
(4)
(1)
(1) multi-function display
(2) gear position indicator
(3) oil change indicator
(5)
(4) speedometer
(5) odometer/tripmeter/ hourmeter
18
Instruments & Controls
08/07/07 14:21:22 32HP4620 0028
Indicators & Displays
Gear Position Indicator
ignition switch is in the ON ( ) position.
The indicator displays: N for neutral, R for reverse, and five forward gears.
1 − 5 for the
‘‘ − ’’ will be displayed on the gear position indicator when the transmission is not shifted into gear properly. Before riding, check that the gear position is properly displayed on the gear position indicator.
If the gear position indicator shows ‘‘ − ’’ and blinks, turn the ignition switch to the OFF ( ) position, and then turn it back to the ON ( ) position again. If the gear position indicator still shows ‘‘ − ’’ and blinks, see your Honda dealer.
(1)
(1) gear position indicator
Instruments & Controls
19
08/07/07 14:21:31 32HP4620 0029
Indicators & Displays
Oil Change Indicator
operating hours on your ATV approaches the oil change interval specified on the maintenance schedule.
Reset the indicator after each oil change.
To reset the indicator, press and hold the hourmeter/odometer/tripmeter than 5 seconds. The indicator message will disappear.
If the oil is changed before the oil change indicator appears, be sure to reset the oil change indicator after changing the oil. The indicator will appears for 5 seconds, then disappear. This means the indicator is reset.
(1) ON
(2)
(1) oil change indicator
(2) hourmeter/odometer/ tripmeter select button
(3) ignition switch
20
Instruments & Controls
ON
(3)
08/07/07 14:21:40 32HP4620 0030
Indicators & Displays
Odometer
kilometers while the ignition is ON ( ). To change the display from tripmeter or hourmeter to odometer, press and release the hourmeter/
(1)
(1) odometer
(2)
(2) hourmeter/odometer/tripmeter select button
Tripmeter
ignition is ON ( ). To change the display from odometer or hourmeter to tripmeter, press and release the hourmeter/odometer/tripmeter select tripmeter select button and hold it in for at least 2 seconds.
(1) (2)
(1) tripmeter (2) hourmeter/odometer/tripmeter select button
Instruments & Controls
21
08/07/07 14:21:46 32HP4620 0031
Indicators & Displays
Hourmeter
ignition is ON ( ). The hourmeter provides accurate service period information for initial and regular maintenance. To change the display from odometer or tripmeter to hourmeter, press and release the
(3)
(1)
(1) hourmeter
(2) hourmeter/odometer/ tripmeter select button
(2)
(3) hourmeter mark
22
Instruments & Controls
08/07/07 14:21:54 32HP4620 0032
Indicators & Displays
Fuel Gauge
(Full), the fuel tank capacity including reserve is:
13.3
(3.51 US gal , 2.93 Imp gal) you should refill the tank as soon as possible. The amount of fuel left in the tank when the needle enters the red band is approximately:
2.9
(0.77 US gal , 0.64 Imp gal)
(2) (1)
(3)
(1) fuel gauge
(2) gauge needle
(3) red band
Instruments & Controls
23
08/07/07 14:22:06 32HP4620 0033
Controls & Features
Fuel Valve
RIGHT SIDE
ON
(1)
OFF RES
(1) fuel valve tank.
The three-way fuel valve is used to control the flow of fuel from the fuel tank to the fuel pump unit.
ON − normal position for riding.
OFF − for parking, storing, or transportation.
RES − for extra fuel to get to a gas supply for refueling.
Reserve Fuel
Remember to check that the fuel valve is in the ON position each time you refuel. If the fuel valve is left in the RES position, you may run out of fuel with no reserve.
For complete information about fueling your ATV, see page 103 .
24
Instruments & Controls
08/07/07 14:22:16 32HP4620 0034
Controls & Features
Ignition Switch
(page 60 ). Insert the key and turn it to the right for the ON ( ) position.
The ignition switch is also used to reset the oil change indicator
(page 20 ).
Key Position
ON ( )
OFF ( )
CENTRE OF HANDLEBAR
Function
Electrical circuits on.
No electrical circuits function.
ON
OFF
(1) ignition switch
(1)
ON
OFF
Instruments & Controls
25
08/07/07 14:22:24 32HP4620 0035
Controls & Features
2WD/4WD Select Lever (
TRX420FM
only)
permits a choice between the ‘‘2WD’’ and ‘‘4WD’’ drive modes. Select a drive mode that’s suitable for your riding.
Keep both hands on the handlebar while machine is in motion and come to a complete stop before using the 2WD/4WD select lever.
The 2WD/4WD select lever is located on the left side of the fuel tank.
To select the drive mode, shift the 2WD/4WD select lever to the desired position.
After using the 2WD/4WD select lever, the mode may not mechanically engage until forward motion begins.
2WD mode : the 4WD indicator goes off when the 2WD mode engages.
4WD mode : the 4WD indicator goes on when the 4WD mode engages.
(1) (2)
4WD MODE
2WD MODE
2WD MODE 4WD MODE
(1) 2WD/4WD select lever (2) 4WD indicator
26
Instruments & Controls
08/07/07 14:22:33 32HP4620 0036
Controls & Features
Start Button
LEFT HANDLEBAR
(2)
(1)
(1) start button
(2) engine stop switch
START
OFF
RUN starts the engine. See Starting Procedure, page 61 .
When the start button is pushed, the starter motor will crank the engine.
The starter motor will not operate if the engine stop switch is in the OFF
( ) position when the start button is pushed.
Engine Stop Switch
To operate, slide the switch to the OFF ( ) position. The switch must be in the RUN ( ) position to start the engine, and it should normally remain in the RUN ( ) position even when the engine is OFF.
If your ATV is stopped with the ignition switch ON ( ) and the engine stop switch OFF ( ), the battery will discharge. Turn the ignition switch OFF ( ) to prevent battery discharge.
Instruments & Controls
27
08/07/07 14:22:41 32HP4620 0037
Controls & Features
Headlight Switch
LEFT HANDLEBAR
(1)
(2) (3)
(1) headlight switch
(2) headlight dimmer switch
(3) horn button
ON
OFF
HI
LO
The headlight switch ( ) is used to turn the headlight ON ( ) or OFF
( ). To operate, turn the switch to ON ( ) or OFF ( ).
Headlight Dimmer Switch
and low beams of the headlight. To operate, turn the switch to HI ( ) for high beam, LO ( ) for low beam.
Horn Button
28
Instruments & Controls
08/07/07 14:22:48 32HP4620 0038
Controls & Features
Recoil Starter
RIGHT SIDE
(1)
(1) recoil starter
See Using the Recoil Starter, page 64 .
Instruments & Controls
29
08/07/07 14:22:55 32HP4620 0039
Controls & Features
Throttle Lever
RIGHT HANDLEBAR
(A)
(1) throttle lever
(1)
(A) to open the throttle
The throttle controls engine rpm (speed). To increase engine rpm, press pressure on the throttle lever. The throttle will automatically return to the closed position (engine idle) when you remove your thumb.
30
Instruments & Controls
08/07/07 14:23:01 32HP4620 0040
Controls & Features
Reverse Selector Knob
stopped and the transmission in neutral (make sure the gear position indicator shows ‘‘N’’), push in the knob, squeeze the rear brake lever/ parking brake lever, then depress the shift lever. See Riding in Reverse, page 67 .
LEFT HANDLEBAR
(1)
(2)
(1) reverse selector knob
(2) rear brake lever/parking brake lever
Instruments & Controls
31
08/07/07 14:23:08 32HP4620 0041
Controls & Features
Front Brake Lever
The front brake lever is used to slow or stop your ATV. To operate, pull the lever. For information on braking techniques, see page 69 .
Rear Brake Lever/Parking Brake Lever
The rear brake lever/parking brake lever is used to slow or stop your
ATV. To operate, pull the lever. For information on braking techniques, see page 69 .
Rear Brake Pedal
The rear brake pedal is used to slow or stop your ATV. To operate, depress the pedal. For information on braking techniques, see page 69 .
32
Instruments & Controls
08/07/07 14:23:16 32HP4620 0042
Controls & Features
Parking Brake
LEFT HANDLEBAR
(1)
(2)
(A)
(1) lock lever
(2) rear brake lever/ parking brake lever
(A) to lock
2 allows it to be used as a parking brake. To operate, first squeeze the rear brake lever/parking brake lever using your left hand and then lock it with the lock lever using your right hand. See Parking page 83 .
The brakelights are activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch OFF ( ) to avoid discharging the battery.
Instruments & Controls
33
08/07/07 14:23:23 32HP4620 0043
Controls & Features
Flag Pole Bracket
RIGHT REAR
(1)
(1) flag pole bracket
Flag poles are optional equipment available from your Honda dealer. To the flag pole kit.
Flag poles are required in some riding areas. Check local regulations before riding.
34
Instruments & Controls
08/07/07 14:23:30 32HP4620 0044
Controls & Features
Trailer Hitch
REAR
(2)
(1) trailer hitch
(1)
(2) ball manufacturer.
To attach the ball and properly hook up a trailer, follow the trailer manufacturer’s instructions. For load limits and operational guidelines, see page 48 .
Instruments & Controls
35
08/07/07 14:23:32 32HP4620 0045
36
Instruments & Controls
08/07/07 14:23:48 32HP4620 0046
Before Riding
Before each ride, you need to make sure you and your Honda are both ready to ride. To help get you prepared, this section discusses how to evaluate your riding readiness, what items you should check on your
ATV, and adjustments to make for your comfort, convenience, or safety.
This section also includes important information about loading.
Are You Ready to Ride?
.......................................................................
.
38
Protective Apparel .............................................................................
.
38
Rider Training ...................................................................................
.
40
Age Recommendation .......................................................................
.
41
No Passengers ...................................................................................
.
41
No Alcohol or Drugs .........................................................................
.
42
Is Your ATV Ready to Ride?
................................................................
.
43
Pre-ride Inspection ............................................................................
.
43
Load Limits & Guidelines .....................................................................
.
47
Loading .............................................................................................
.
47
Load Limits .......................................................................................
.
48
Loading Guidelines ...........................................................................
.
49
Accessories & Modifications ................................................................
.
50
Accessories ........................................................................................
.
50
Modifications ....................................................................................
.
51
Before Riding
37
08/07/07 14:24:01 32HP4620 0047
Are You Ready to Ride?
Before you ride your ATV for the first time, we urge you to:
Read this owner’s manual and the labels on your ATV carefully.
Make sure you understand all the safety messages.
Know how to operate all the controls.
Before each ride, be sure:
You feel well and are in good physical and mental condition.
You are wearing an approved motorcycle helmet (with chin strap tightened securely), eye protection, and other protective clothing.
You don’t have any alcohol or drugs in your system.
Protective Apparel
For your safety, we strongly recommend that you always wear an approved motorcycle helmet, eye protection, boots, gloves, long pants, and a long-sleeved shirt or jacket whenever you ride.
Although complete protection is not possible, wearing proper gear can reduce the chance of injury when you ride.
Following are suggestions to help you choose the proper gear.
Helmets and Eye Protection
Your helmet is your most important piece of riding gear because it offers the best protection against head injuries. A helmet should fit your head comfortably and securely.
38
Before Riding
08/07/07 14:24:09 32HP4620 0048
Are You Ready to Ride?
An open-face helmet offers some protection, but a full-face helmet offers more. Always wear a face shield or goggles to protect your eyes and help your vision.
Operating this ATV without wearing an approved motorcycle helmet, eye protection, and protective clothing could increase your chances of severe injury or death in the event of an accident.
Always wear an approved motorcycle helmet that fits properly and wear eye protection
(goggles or face shield), gloves, boots, long-sleeved shirt or jacket and long pants.
Additional Riding Gear
In addition to a helmet and eye protection, we also recommend:
Sturdy off-road motorcycle boots to help protect your feet, ankles, and lower legs.
Off-road motorcycle gloves to help protect your hands.
Riding pants with knee and hip pads, a riding jersey with padded elbows, and a chest/shoulder protector.
Before Riding
39
08/07/07 14:24:15 32HP4620 0049
Are You Ready to Ride?
Rider Training
Developing your riding skills is an on-going process. Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice riding the ATV in a safe area to build your skills. Do not ride in rough terrain until you get accustomed to the
ATV’s controls, and feel comfortable with its size and weight.
Operating this ATV without proper instruction could increase your risk of an accident which could lead to serious injury or death.
Beginning and inexperienced operators should complete the certified training course offered by
Honda. They should then regularly practice the skills learned in the course and the operating techniques described in the owner’s manual.
40
Before Riding
08/07/07 14:24:24 32HP4620 0050
Are You Ready to Ride?
Age Recommendation
The minimum recommended age for this ATV model is 16. For safety, never let children under 16 years old operate this vehicle.
A child using an ATV that is not recommended for their age could lose vehicle control while riding, resulting in severe injury or death.
A child under 16 should never operate an ATV with engine size greater than 90cc.
No Passengers
This ATV is designed as an operator-only vehicle. The long seat is designed to allow the rider to change body position, not for carrying a passenger. Never let a passenger ride on the seat or on the front or rear cargo racks.
Carrying a passenger on this ATV greatly reduces your ability to balance and control this
ATV and could cause a crash and you or your passenger could be injured or killed.
Never carry a passenger on this ATV.
Before Riding
41
08/07/07 14:24:30 32HP4620 0051
Are You Ready to Ride?
No Alcohol or Drugs
Alcohol, drugs and ATVs don’t mix. Even a small amount of alcohol can impair your ability to operate an ATV safely. Likewise, drugs − even if prescribed by a physician − can be dangerous while operating an
ATV. Consult your doctor to be sure it is safe to operate a vehicle after taking medication.
Operating this ATV after consuming alcohol or drugs can seriously affect your judgement, cause you to react more slowly, affect your balance and perception, and result in serious injury or death.
Never consume alcohol or drugs before or while operating this ATV.
42
Before Riding
08/07/07 14:24:41 32HP4620 0052
Is Your ATV Ready to Ride?
Before each ride, it’s important to inspect your ATV and make sure any problem you find is corrected. A pre-ride inspection is a must, not only for safety, but because having a breakdown, or even a flat tyre, can be a major inconvenience.
If your ATV has overturned or been involved in a collision, do not ride the vehicle until it has been inspected by your Honda dealer. There may be damage or other problems you cannot see.
Improperly maintaining this ATV or failing to correct a problem before riding can cause a crash in which you can be seriously hurt or killed.
Always perform a pre-ride inspection before every ride and correct any problems.
Pre-ride Inspection
Check the following items before you get on the ATV:
Engine Oil
Radiator
Coolant
Check the level and add oil if needed
(page 108 ).
Check for leaks.
Check the coolant level and add coolant if needed (page 119
Check for leaks.
).
Before Riding
43
08/07/07 14:24:56 32HP4620 0053
Is Your ATV Ready to Ride?
Fuel
Tyres
Drivetrain Boots
Guards
Nuts & Bolts
Underbody &
Exhaust System
Air Cleaner Housing
Drain Tube
Leaks, Loose Parts
Check the level and add fuel (page 103 ) if needed. Also make sure the fuel fill cap is securely fastened.
Check for leaks.
Use a gauge to check the air pressure. Adjust if needed. Also look for signs of damage or excessive wear (page 153 ).
).
Check for damage (pages
Check for damage or looseness
(pages ).
Check the wheels to see that the axle nuts are tightened. Use a wrench to make sure all accessible nuts, bolts, and fasteners are tight.
Check for, and remove, any dirt, vegetation or other debris that could be a fire hazard or interfere with the proper operation of the vehicle.
Check for deposits in the drain tube. If necessary, clean the tube (page 129 ) and check the air cleaner housing.
Walk around your ATV and look for anything that appears unusual, such as a leak or loose cable.
44
Before Riding
08/07/07 14:25:10 32HP4620 0054
Is Your ATV Ready to Ride?
Cable Check the cable housings for wear. Check the fittings for looseness. Replace or tighten as needed.
Lights Make sure the headlight, brakelight and taillight are working properly.
If you are carrying cargo, also check the following:
Loading Limits
Reverse Assist Lever
Make sure you do not exceed the load limits
(page 48 ).
Check that all cargo is secure.
Cargo
Check these items after you get on the ATV:
Throttle Check the freeplay and adjust if needed. Press the throttle to make sure it moves smoothly without sticking, and snaps shut automatically when it is released, in all steering positions
(page 130 ).
Brakes Squeeze the front and rear brake levers and step on the rear brake pedal to check that the controls operate normally. Check for proper freeplay (pages , ). Make sure there is no brake fluid leakage.
Check the freeplay and adjust if needed
(page 133 ). Make sure the lever operates smoothly without sticking.
Before Riding
45
08/07/07 14:25:19 32HP4620 0055
Is Your ATV Ready to Ride?
Headlight and
Headlight Dimmer
Switch
Check for proper function (page 28 ).
Engine Stop Switch
Steering
Check for proper function (page 27 ).
Check that the wheels turn properly as you steer the handlebar. Move the handlebar right and left and check that there is no excessive backlash.
Remember, be sure to take care of any problem you find, or have your
Honda dealer correct it before you ride.
46
Before Riding
08/07/07 14:25:26 32HP4620 0056
Load Limits & Guidelines
Your Honda was designed as a rider-only ATV. It was not designed to carry a passenger. It can carry cargo on the cargo racks, however, carrying cargo anywhere else or carrying a passenger could interfere with your balance and control of the ATV.
In addition, exceeding the weight limits or carrying an unbalanced load can seriously affect your ATV’s handling, braking and stability. Adding accessories or making modifications that change this ATV’s design and performance can also make it unsafe. Also, the weight of any accessories will reduce the maximum load the ATV can carry.
More specific information on load limits, accessories, and modifications follows.
Loading
How much weight you put on your ATV, and how you load it, are important to your safety. If you decide to carry cargo, you should be aware of the following information.
Overloading, improper loading, or carrying a passenger can cause a crash and you can be seriously hurt or killed.
Follow all load limits and other loading guidelines in this manual.
Before Riding
47
08/07/07 14:25:41 32HP4620 0057
Load Limits & Guidelines
Load Limits
Following are the load limits for your ATV:
There are limits to how much weight can be carried on your ATV and be pulled in a trailer.
The following load limits apply to standard equipment only. Modifying your ATV, using non-standard equipment, or riding on terrain that is not flat and smooth could further reduce these limits.
220 kg (485 lbs) maximum weight capacity
(includes the weight of the rider, all cargo, and accessories.) front cargo rack weight limit rear cargo rack weight limit tow weight limit
(Combined weight of the trailer and all cargo in the trailer) tongue weight
(Weight on the trailer tongue) tongue and rear cargo weight
(Combined weight on the trailer tongue and on the rear cargo rack)
=
=
=
30 kg (66 lbs)
60 kg (133 lbs)
385 kg (850 lbs)
=
=
14 kg (30 lbs) recommended
60 kg (133 lbs) maximum
Tongue weight can be measured with an ordinary bathroom scale. Place the scale under the tongue, using either a tongue jack or other support to keep the trailer level.
The weight of added accessories will reduce the maximum cargo weight you can carry.
48
Before Riding
08/07/07 14:25:55 32HP4620 0058
Load Limits & Guidelines
Loading Guidelines
Carrying cargo or pulling a trailer will affect how your ATV handles and greatly reduce its ability in accelerating, braking and making turns and other maneuvers.
Be sure to observe the weight limits and follow these guidelines:
Check that the tyres are properly inflated.
Do not place cargo anywhere on the ATV other than on the front and rear racks. Otherwise, operating stability may be adversely affected.
Never ride with a passenger on the front or rear cargo racks. The
ATV is not designed to carry a passenger.
Use the trailer hitch to tow another vehicle or trailer. Do not tow by tying a rope or cable to the rear rack.
Load cargo on the rear rack as far forward as possible. Make sure cargo on the front rack does not interfere with handlebar movement.
Do not allow cargo to extend beyond the edges of either the front or rear racks.
Make sure all cargo is secured before riding.
Balance cargo weight evenly on both sides.
Never exceed the maximum weight limit.
When towing a trailer, take care to maintain balance and stability.
Distribute cargo between the front and rear of the trailer to obtain the recommended tongue weight.
Allow extra room for starting, stopping and turning whenever you carry cargo or pull a trailer.
Avoid riding on steep slopes when carrying cargo or pulling a trailer.
Never cross a slope when towing a trailer.
Before Riding
49
08/07/07 14:26:04 32HP4620 0059
Accessories & Modifications
Modifying your ATV or using non-Honda accessories can make your
ATV unsafe.
Before you consider making any modifications or adding an accessory, be sure to read the following information.
Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding accessories and modifications.
Accessories
We strongly recommend that you use only Honda Genuine Accessories that have been specifically designed and tested for your ATV. Because
Honda cannot test all other accessories, you must be personally responsible for proper selection, installation, and use of non-Honda accessories.
Check with your Honda dealer for assistance and always follow these guidelines:
Make sure the accessory does not obscure any lights, reduce ground clearance, limit suspension travel or steering travel, or interfere with operating any controls.
Make sure the accessory does not interfere with your ability to shift body position on the seat or operate hand and foot controls.
Do not add any electrical equipment that will exceed the vehicle’s electrical system capacity (page 207 ). A blown fuse can cause a loss of lights or engine power (page 192 ).
50
Before Riding
08/07/07 14:26:09 32HP4620 0060
Accessories & Modifications
Modifications
We strongly advise you not to remove any original equipment or modify your ATV in any way that would change its design or operation. Such changes could seriously impair your ATV’s handling, stability, and braking, making it unsafe to ride.
Removing or modifying your lights, exhaust system, emission control system, or other equipment can also make your ATV illegal.
Before Riding
51
08/07/07 14:26:12 32HP4620 0061
52
Before Riding
08/07/07 14:26:29 32HP4620 0062
Basic Operation & Riding
This section gives basic riding instructions, including how to start and stop your engine, and how to use the throttle and brakes. It also provides important information on riding with cargo.
To protect your new engine and enjoy optimum performance and service life, refer to Break-in Guidelines (page 208 ).
Safe Riding Precautions ........................................................................
.
55
Off-road Use Only ............................................................................
.
55
Keep Hands and Feet on Controls .....................................................
.
56
Control Speed ....................................................................................
.
57
Use Care on Unfamiliar or Rough Terrain ........................................
.
58
Do Not Perform Stunts ......................................................................
.
59
Starting & Stopping the Engine ............................................................
.
60
Preparation ........................................................................................
.
60
Starting Procedure .............................................................................
.
61
Flooded Engine .................................................................................
.
62
Bank Angle Sensor Ignition Cut-off System ....................................
.
62
Stalled Engine ...................................................................................
.
63
How to Stop the Engine ....................................................................
.
63
Using the Recoil Starter ....................................................................
.
64
Shifting Gears .......................................................................................
.
65
Riding in Reverse ..................................................................................
.
67
(cont’d)
Basic Operation & Riding
53
08/07/07 14:26:40 32HP4620 0063
Basic Operation & Riding
Braking ..................................................................................................
.
69
Riding Your ATV .................................................................................
.
71
Making Turns ....................................................................................
.
71
Skidding or Sliding ...........................................................................
.
73
Riding Up Hills .................................................................................
.
74
Riding Down Hills ............................................................................
.
78
Crossing or Turning on Hills or Slopes .............................................
.
79
Riding Over Obstacles ......................................................................
.
81
Riding Through Water ......................................................................
.
82
Parking ..................................................................................................
.
83
54
Basic Operation & Riding
08/07/07 14:26:48 32HP4620 0064
Safe Riding Precautions
Before riding your ATV for the first time, please review the ATV Saf ety section beginning on page 1, and the Bef ore Riding section beginning on page 37 .
Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.
Off-road Use Only
Your ATV and its tyres are designed and manufactured for off-road use only, not for pavement. Riding on pavement can affect handling and control. You should not ride your ATV on pavement.
Operating this ATV on paved surfaces may seriously affect handling and control of the ATV, and may cause the vehicle to go out of control.
Never operate the ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets.
When riding off-road, also remember to always obey local off-road riding laws and regulations. Obtain permission to ride on private property. Avoid posted areas and obey ‘‘no trespassing’’ signs.
Basic Operation & Riding
55
08/07/07 14:26:55 32HP4620 0065
Safe Riding Precautions
You should never ride your ATV on public streets, roads or highways, even if they are not paved. Drivers of street vehicles may have difficulty seeing and avoiding you, which could lead to a collision. In many states it is illegal to operate ATVs on public streets, roads and highways.
Operating this ATV on public streets, roads or highways could cause you to collide with another vehicle.
Never operate this ATV on any public street, road or highway, even a dirt or gravel one.
Keep Hands and Feet on Controls
Always keep both hands on the handlebars and both feet on the footpegs when riding your ATV. This is important to maintain your balance and to control the vehicle. Removing even one hand from the handlebars or one foot from the footpegs can reduce your ability to control the ATV or could cause you to lose your balance and fall off the ATV.
Removing hands from handlebars or feet from footpegs during operation can reduce your ability to control the ATV or could cause you to lose your balance and fall off of the ATV.
Always keep both hands on the handlebars and both feet on the footpegs of your ATV during operation.
56
Basic Operation & Riding
08/07/07 14:27:00 32HP4620 0066
Safe Riding Precautions
Control Speed
Riding at excessive speed increases the chance of an accident. In choosing a proper speed, you need to consider the capability of your vehicle, the terrain, visibility and other operating conditions, plus your own skills and experience.
Operating this ATV at excessive speeds increases your chances of losing control of the
ATV, which can result in an accident.
Always go at a speed that is proper for your vehicle, the terrain, visibility and other operating conditions, and your experience.
Basic Operation & Riding
57
08/07/07 14:27:06 32HP4620 0067
Safe Riding Precautions
Use Care on Unfamiliar or Rough Terrain
Before riding in a new area, always check the terrain thoroughly. Don’t ride fast on unfamiliar terrain or when visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or holes in time to react.)
Failure to use extra care when operating this
ATV on unfamiliar terrain could result in the ATV overturning or going out of control.
Go slowly and be extra careful when operating on unfamiliar terrain. Always be alert to changing terrain conditions when operating the
ATV.
58
Basic Operation & Riding
08/07/07 14:27:13 32HP4620 0068
Safe Riding Precautions
Never ride past the limit of visibility. Maintain a safe distance between your ATV and other off-road vehicles. Always exercise caution, and use extra care on rough, slippery and loose terrain.
Failure to use extra care when operating on excessively rough, slippery or loose terrain could cause loss of traction or vehicle control, which could result in an accident, including an overturn.
Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control the ATV on such terrain. Always be especially cautious on these kinds of terrain.
Do Not Perform Stunts
You should always operate your ATV in a safe and reasonable manner.
When riding, always keep all four wheels on the ground.
Attempting wheelies, jumps, and other stunts increases the chance of an accident, including an overturn.
Never attempt stunts, such as wheelies or jumps. Don’t try to show off.
Basic Operation & Riding
59
08/07/07 14:27:25 32HP4620 0069
Starting & Stopping the Engine
Always follow the proper starting procedure described below.
For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your ATV’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death.
Preparation
(1)
(2)
(3)
(1) fuel valve
(2) ignition switch
(3) neutral indicator
(4)
(4) engine stop switch
1.
Before starting, select a level surface and lock the parking brake
(page 33 ).
2.
2 ).
Confirm the following:
The engine stop switch ( ) is set to RUN ( ).
60
Basic Operation & Riding
08/07/07 14:27:32 32HP4620 0070
Starting & Stopping the Engine
Starting Procedure
This vehicle has a fuel-injected engine with an automatic choke.
Follow the procedure indicated below.
Any Air Temperature
Press the start button with the throttle completely closed.
The engine will not start if the throttle is fully open (because the electronic control module cuts off the fuel supply).
Basic Operation & Riding
61
08/07/07 14:27:44 32HP4620 0071
Starting & Stopping the Engine
Flooded Engine
If the engine fails to start after repeated attempts, it may be flooded with excess fuel. To clear a flooded engine:
1.
Leave the engine stop switch set to RUN ( ).
2.
Open the throttle fully.
3.
Press the start button for 5 seconds (or operate the recoil starter several times).
4.
5.
Follow the normal starting procedure.
If the engine starts, then open the throttle slightly if idling is unstable.
If the engine does not start, wait 10 seconds, then follow steps
1 − 4 again.
If the engine still won’t start, refer to If Your Engine Quits or Won’t
Start, page 184 .
Bank Angle Sensor Ignition Cut-off System
Your vehicle’s banking (lean angle) sensor system is designed to automatically stop the engine if the vehicle is overturned.
Before restarting the engine, you must turn the ignition switch to the
OFF ( ) position and then back to ON ( ). The engine will not restart until you perform this procedure.
62
Basic Operation & Riding
08/07/07 14:27:54 32HP4620 0072
Starting & Stopping the Engine
Stalled Engine
You can restart the engine while the vehicle is stopped by squeezing the front brake lever and pressing the start button.
Do not press the throttle lever while starting in gear. Your ATV is equipped with a start inhibitor system that will cut off the ignition if the throttle is open while attempting to start in gear.
Once you have started the engine, release the front brake lever, then apply throttle gradually.
How to Stop the Engine
Normal Engine Stop
To stop the engine, make sure the transmission is in neutral by checking that the neutral indicator light is on, then turn the ignition switch OFF
( ).
The engine stop switch should normally remain in the RUN ( ) position even when the engine is OFF.
If your ATV is stopped with the engine stop switch OFF ( ) and the ignition switch ON ( ), the battery will discharge.
Emergency Engine Stop
To stop the engine in an emergency, use the engine stop switch. To operate, slide the switch to either OFF ( ) position.
Basic Operation & Riding
63
08/07/07 14:28:02 32HP4620 0073
Starting & Stopping the Engine
Using the Recoil Starter
The recoil starter is used to start the engine when the battery is low.
To operate the recoil starter:
1.
Check that the transmission is in neutral.
2.
100 mm (4 in).
3.
Pull the grip up briskly and fully.
4.
After the engine starts, allow the starter grip to return slowly.
If the starter grip does not return smoothly (because of dirt in the assembly), see your Honda dealer.
RIGHT SIDE
(1) starter grip
(1)
64
Basic Operation & Riding
08/07/07 14:28:11 32HP4620 0074
Shifting Gears
UPSHIFTING SEQUENCE
DOWNSHIFTING SEQUENCE
Your ATV has five forward gears: 1, 2, 3, 4, and 5.
The shift lever is located near the left footpeg. One full stroke of the shift lever shifts the transmission to the next higher or lower gear in the shifting sequence. The shift lever automatically returns to the horizontal position when released.
To upshift to a higher gear, put the toe of your boot under the shift lever and raise it one full stroke. To downshift, step on the shift lever and depress it one full stroke.
To select reverse, use the reverse selector knob (page 67 ).
Basic Operation & Riding
65
08/07/07 14:28:24 32HP4620 0075
Shifting Gears
After starting the engine and letting it warm up, follow these procedures:
1.
With the transmission in neutral, release the parking brake, but continue squeezing the rear brake lever.
2.
With the throttle closed, raise the shift lever one full stroke to shift
3.
into 1st (first) gear.
Release the rear brake lever and increase engine speed by gradually opening the throttle.
4.
When speed increases, release the throttle and shift to 2nd gear by raising the shift lever one full stroke.
5.
Repeat this sequence to progressively upshift to 3rd, 4th and 5th (top) gear.
6.
To downshift, reverse this sequence. Remember to close the throttle each time you shift to the next lower gear.
Learning when to shift gears comes with experience. Keep the following tips in mind:
As a general rule, shift while moving in a straight line.
Close the throttle completely before shifting. Improper shifting may damage the engine, transmission, and drivetrain.
Upshift to a higher gear or reduce throttle before engine rpm (speed) gets too high. Learn the relationship between engine sound and the normal shifting points.
Downshift to a lower gear before you feel the engine laboring
(lugging) at low rpm.
Avoid downshifting to help slow your ATV when engine rpm is high.
Downshifting when engine speed is near its allowable maximum may over-rev the engine and possibly cause damage.
To prevent transmission damage, do not coast or tow the ATV for long distances with the engine off.
Recommended Shift Points
Ride in the highest gear that lets the engine run and accelerate smoothly.
This will give you good fuel economy and effective emissions control.
66
Basic Operation & Riding
08/07/07 14:28:33 32HP4620 0076
Riding in Reverse
If you need to ride in reverse, make sure the area behind you is clear and only operate the ATV at low speed.
Improperly operating in reverse could cause you to hit an obstacle or person behind you, resulting in serious injury.
Make sure there are no obstacles or people behind you before selecting reverse gear. When it is safe to proceed, go slowly.
1.
Bring the vehicle to a complete stop, then make sure the transmission is in neutral.
2.
Be sure there are no obstacles or people in the way.
3.
LEFT HANDLEBAR
(1)
(2)
(1) reverse selector knob
(2) rear brake lever/parking brake lever
(cont’d)
Basic Operation & Riding
67
08/07/07 14:28:40 32HP4620 0077
Riding in Reverse
Your ATV may be equipped with a reverse speed limiter, which helps the vehicle to maintain a saf e speed while riding in reverse gear.
4.
5.
Release the rear brake lever/parking brake lever.
Open the throttle gradually and ride slowly. Do not open the throttle suddenly or make abrupt turns.
6.
To stop, close the throttle and gradually apply both the front and rear brakes. Do not abruptly apply the rear brake by itself.
7.
To shift out of reverse and into neutral, raise the shift lever one stroke.
Applying only the rear brake abruptly when operating in reverse gear could cause the front wheels to lift off the ground and the ATV could overturn backwards.
Carefully apply both the front and rear brakes when stopping in reverse gear.
68
Basic Operation & Riding
08/07/07 14:28:49 32HP4620 0078
Braking
Your ATV is equipped with disc brakes on both front wheels which are hydraulically activated by operating the right brake lever. A single drum brake on the rear axle housing is mechanically activated by depressing the brake pedal or operating the left brake lever.
TRX420FM only:
Although the front and rear brakes have separate controls, all four wheels are interconnected when your ATV is in the 4WD mode. So operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.
As a general rule, the front braking system provides about 70 percent of total stopping power.
For full braking effectiveness, use both the pedal and lever simultaneously. Using both braking systems will stop your ATV faster with greater stability.
To slow or stop, apply the brake lever and brake pedal smoothly, while downshifting to match your speed.
Gradually increase braking as you feel the brakes slowing your speed.
The increase in engine compression from downshifting will help slow your ATV.
Applying the brakes too hard may cause the wheels to lock and slide, reducing control of your ATV. If this happens, release the brake controls, steer straight ahead until you regain control, then reapply the brakes more gently.
When possible, reduce your speed or complete braking before entering a turn. Avoid braking or closing the throttle quickly while turning. Either action may cause one or more wheels to slip and reduce your control of your ATV.
Basic Operation & Riding
69
08/07/07 14:28:55 32HP4620 0079
Braking
Your ability to brake in a turn and to brake hard in an emergency situation are important riding skills.
When descending a long, steep grade, use engine compression braking by downshifting, with intermittent use of both brakes. Continuous brake application can overheat the brakes and reduce their effectiveness.
Riding with your foot resting on the brake pedal or your hands on the brake levers may overheat the brakes, reducing effectiveness.
For information on how to apply the brakes in various riding situations, see the following section, Riding Your ATV .
70
Basic Operation & Riding
08/07/07 14:29:02 32HP4620 0080
Riding Your ATV
Making Turns
Learn how to turn your ATV properly. Practice the techniques outlined in this section on level ground and at low speeds until you are confident in making turns.
Turning improperly can make the ATV go out of control, causing a collision or overturn.
Always follow proper procedures for turning as described in this owner’s manual.
Practice turning at low speeds before attempting to turn at faster speeds.
Do not turn at excessive speeds.
Basic Operation & Riding
71
08/07/07 14:29:09 32HP4620 0081
Riding Your ATV
Lean your body to the inside of a turn and forward.
To make a turn on level ground: Steer the handlebar and lean your body toward the inside of the turn. Leaning helps balance the vehicle, and it feels more comfortable. Leaning into a turn is an important technique to master in riding an ATV.
To make a sharp turn at low speed: It helps to shift your body slightly forward on the seat, and lean inside, as you steer the handlebar. Shifting weight forward allows the rear wheels to turn easier, and it also improves front-wheel steering.
To make a turn from a full stop: Apply the throttle gradually when you turn and start up at the same time. Remember to shift your body forward to make sharp low-speed turns and whenever you turn while accelerating from a full stop.
72
Basic Operation & Riding
08/07/07 14:29:16 32HP4620 0082
Riding Your ATV
Skidding or Sliding
The terrain surface can be a major factor affecting turns. Skidding during a turn is more likely to occur on slippery surfaces, such as snow, ice, mud and loose gravel. If you skid on ice, you may lose all directional control. To avoid skidding on slippery terrain, keep your speed low and ride with caution.
Skidding or sliding improperly may cause you to lose control of this ATV. You may also regain traction unexpectedly, which may cause the
ATV to overturn.
Learn to safely control skidding by practicing at low speeds and on level, smooth terrain.
If your ATV skids sideways during a turn, steer in the direction of the skid. Avoid hard braking or accelerating until you have regained directional control.
Basic Operation & Riding
73
08/07/07 14:29:23 32HP4620 0083
Riding Your ATV
Riding Up Hills
The ATV’s ability to safely climb hills largely depends on the rider’s skill and judgment. Begin by practicing on smooth, gentle slopes. As you gain experience, you’ll learn the hazards and your own limitations.
You may then proceed to ride on more difficult terrain. However, you must be able to decide which hills or hazards might cause the ATV to overturn. Avoid excessively steep hills.
Operating on excessively steep hills can cause the vehicle to overturn more easily than operating on level surfaces or small hills.
Never operate the ATV on hills too steep for the
ATV or for your abilities.
When climbing hills, you must shift weight toward the front wheels to help keep them on the ground. To do this, shift your body slightly forward on the seat and lean forward. For greater weight shift, move your body farther forward and lean forward.
Climbing hills improperly could cause loss of control or cause the ATV to overturn.
Always follow proper procedures for climbing hills as described in this owner’s manual.
74
Basic Operation & Riding
08/07/07 14:29:31 32HP4620 0084
Riding Your ATV
Shift weight forward when climbing hills.
Always check the terrain carefully before you start up any hill.
Never climb hills with excessively slippery or loose surfaces.
To climb a hill, take a running start in an appropriate gear and speed for the conditions. Maintain a steady speed as you ascend the hill.
Never open the throttle suddenly or make sudden gear changes. The
ATV could flip over backward.
Never go over the top of any hill at high speed. An obstacle, a sharp drop, or another vehicle or person could be on the other side of the hill.
Basic Operation & Riding
75
08/07/07 14:29:42 32HP4620 0085
Riding Your ATV
Stalling the ATV and/or Rolling Backwards:
If you incorrectly estimate climbing capability or terrain conditions, the
ATV may not have enough power or traction to continue uphill. If this happens, the ATV can stall and/or roll backwards.
Stalling, rolling backwards or improperly dismounting while climbing a hill could result in the ATV overturning.
Always follow proper procedures for climbing a hill as described in this owner’s manual.
What to do if the ATV stalls or rolls backwards when climbing a hill:
If you are about to lose all forward speed:
1.
Using the front and rear brakes together, bring the ATV to a stop with the vehicle pointed straight uphill.
2.
3.
Get off the ATV while you continue holding the brakes.
Shift into neutral, set the parking brake and turn the engine off.
4.
Then assess the situation.
If the ATV starts rolling backwards before you begin braking:
1.
Keep your weight uphill.
2.
Carefully apply the front brakes first, then carefully apply the rear brake. Do not apply either brake abruptly if you are rolling backwards, or the vehicle may overturn.
If the ATV continues sliding backwards:
After you’ve applied the brakes, get off and away from the vehicle.
TRX420FM only:
Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.
76
Basic Operation & Riding
08/07/07 14:29:52 32HP4620 0086
Riding Your ATV
What to do after the ATV has stalled or rolled backwards:
If the hill is too steep or too slippery, or if you have any doubt whether you can safely walk the ATV back down the hill, leave the vehicle where it is and get help. If possible, block the wheels so the vehicle doesn’t roll backwards.
If the hill is not too steep and you have good footing, you may be able to walk the ATV back down the hill. Make sure your intended path is clear in case you lose control of the ATV.
Be sure your legs are clear of the wheels.
Body position for backing down a hill.
1.
Stand with your body facing downhill, beside the vehicle so you can
2.
reach the rear brake lever with your right hand.
Be sure your legs are clear of the wheels.
3.
Check your footing.
4.
Slowly and carefully back the ATV down the hill using the rear brake lever to control speed.
5.
If you lose control of the ATV, for your safety, get away from the vehicle.
Basic Operation & Riding
77
08/07/07 14:30:01 32HP4620 0087
Riding Your ATV
Riding Down Hills
It’s usually advisable to descend hills with the ATV pointed straight downhill. Avoid angles that would cause the vehicle to lean sharply to one side.
Going down a hill improperly could cause loss of control or cause the ATV to overturn.
Always follow proper procedures for going down hills as described in this owner’s manual.
On downhills, shift your weight back.
As you approach a downhill, stop and survey the terrain below. Never ride past the limit of your visibility. Never go down a hill at high speed.
78
Basic Operation & Riding
08/07/07 14:30:09 32HP4620 0088
Riding Your ATV
When you’ve selected a safe downhill path, shift into a lower gear, shift your weight back with your arms extended and braced against the handlebar, then go down slowly with the throttle closed.
Use mainly the rear brake to control speed. Avoid using either the front brake or rear brake hard or abruptly when riding down hills.
TRX420FM only:
Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.
Remember, braking effectiveness is reduced on any hill with a loose surface.
Crossing or Turning on Hills or Slopes
Riding on hills or slopes is different from riding on level terrain. Be careful when riding on any hill. Make sure that you practice on gentle, smooth slopes before attempting to ride on steeper or more difficult terrain.
Improperly crossing hills or turning on hills could cause loss of control or cause the ATV to overturn.
Always follow proper procedures for crossing or turning on slopes as described in this owner’s manual. Avoid crossing steep hills if possible.
Basic Operation & Riding
79
08/07/07 14:30:18 32HP4620 0089
Riding Your ATV
Crossing Hills or Slopes
To maintain balance and stability when riding across a slope, you need to shift weight toward the uphill side of the vehicle. To do this, move your body off the centre of the seat and lean toward the uphill side.
On a slippery or loose surface, you may also need to steer slightly uphill to maintain a straight course across the slope.
Avoid crossing hills that are excessively steep, slippery or rough.
Shift weight uphill when crossing slopes.
Making Turns on Slopes
Compared to riding on level ground, you may need to shift more weight and lean more when making turns on slopes.
Do not make turns on any slopes until you have first mastered the techniques for making turns on level terrain.
80
Basic Operation & Riding
08/07/07 14:30:23 32HP4620 0090
Riding Your ATV
Riding Over Obstacles
Before operating in a new area, check for obstacles. Watch out for bumps, rain ruts, potholes and other obstacles in the terrain. When you approach any obstacle, reduce your speed and be prepared to stop.
Never try to ride over large obstacles, such as large rocks or fallen logs.
Improperly operating over obstacles could cause loss of control or a collision and could cause the ATV to overturn.
When you go over obstacles, always follow proper procedures as described in this owner’s manual.
Basic Operation & Riding
81
08/07/07 14:30:34 32HP4620 0091
Riding Your ATV
Riding Through Water
Your ATV is designed to travel through water up to approximately
254 mm (10 inches) deep. Before crossing a stream, make sure the water is not too deep or flowing too fast.
The ATV tyres have some ability to float.
Operating this ATV through deep or fast-flowing water may cause a loss of traction and loss of control, which could lead to an accident.
Never operate this ATV in fast-flowing water or in water deeper than that specified in this owner’s manual.
1.
2.
Choose a path where both banks have gradual slopes.
Proceed through the water at a slow, steady speed.
3.
Watch out for submerged obstacles and slippery rocks.
4.
Avoid getting the spark plug or air cleaner wet, as this would cause the engine to stop.
5.
After leaving the water, always test both the front and rear brakes.
Riding through water can make the brakes less effective than normal, and may reduce stopping ability.
If necessary, apply the brakes repeatedly until they dry out and operate normally.
If the brakes don’t regain effectiveness, stop your ATV and follow the procedures on page 149 .
82
Basic Operation & Riding
08/07/07 14:30:49 32HP4620 0092
Parking
1.
2.
Look for level parking area. Make sure the ground surface is firm.
After bringing your ATV to a stop, hold the brakes while you shift into neutral.
3.
Set the parking brake.
4.
Turn the ignition switch OFF ( ).
5.
If you’re finished riding for the day, turn the fuel valve OFF.
If it is necessary to start the engine when your ATV in gear and is stopped on a grade, rock the vehicle back and forth to allow shifting the transmission into neutral.
The brakelights are activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch OFF ( ) to avoid discharging the battery.
Parking on a Steep Incline or a Loose or Slippery Surface
If you must park your ATV on a steep incline or loose or slippery surface, use the following procedure:
1.
2.
While holding the brakes, set the parking brake.
Turn the ignition switch OFF ( ) and release the brakes.
3.
If the ATV begins to move, either while sitting on it or after you dismount, find a better parking location.
4.
If rocks or other objects are available, you can block the wheels as shown for additional security.
Basic Operation & Riding
83
08/07/07 14:30:52 32HP4620 0093
84
Basic Operation & Riding
08/07/07 14:31:05 32HP4620 0094
Servicing Your Honda
To help keep your ATV in good shape, this section includes a
Maintenance Schedule for required service and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on fuels and oils, and tips for keeping your
Honda looking good.
For information about replacing fuses, see page 192 .
Bef ore You Service Your Honda
The Importance of Maintenance ...........................................................
.
87
Maintenance Safety ...............................................................................
.
88
Important Safety Precautions ............................................................
.
89
Maintenance Schedule ..........................................................................
.
90
Maintenance Record ..............................................................................
.
94
Service Preparations
Maintenance Component Locations ......................................................
.
95
Tool Kit .................................................................................................
.
98
Owner’s Manual Storage .......................................................................
.
99
Seat Removal ....................................................................................
.
Clip Removal ....................................................................................
.
100
101
(cont’d)
Servicing Your Honda
85
08/07/07 14:31:23 32HP4620 0095
Servicing Your Honda
Service Procedures
Fluids & Filters
Fuel ...................................................................................................
.
Engine Oil & Filter ............................................................................
.
Gear Case Oil ....................................................................................
.
Differential Oil ( TRX420FM only) ...................................................
.
Coolant ..............................................................................................
.
Air Cleaner ........................................................................................
.
102
105
114
116
118
124
Engine
Throttle ..............................................................................................
.
Clutch System ...................................................................................
.
Reverse Lock System ........................................................................
.
Spark Plug .........................................................................................
.
Valves ................................................................................................
.
Spark Arrester ...................................................................................
.
130
132
133
134
137
138
Chassis
Brakes ................................................................................................
.
Tyres .................................................................................................
.
Guards ...............................................................................................
.
Drivetrain Boots ................................................................................
.
139
150
157
159
Electrical
Battery ...............................................................................................
.
161
Appearance Care ...............................................................................
.
166
86
Servicing Your Honda
08/07/07 14:31:31 32HP4620 0096
The Importance of Maintenance
A well-maintained ATV is essential for safe, economical, and troublefree riding. It will also help reduce air pollution. Careful pre-ride inspections and good maintenance are especially important because your
ATV is designed to be ridden over rough off-road terrain.
To help you properly care for your ATV, this section of the manual provides a Maintenance Schedule. The service intervals in this schedule are based on average riding conditions.
Improperly maintaining this ATV or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.
Frequent servicing of the air cleaner is especially important to help you avoid a possible costly engine repair.
If your ATV overturns or is involved in a crash, be sure your Honda dealer inspects all major parts, even if you are able to make some repairs.
Servicing Your Honda
87
08/07/07 14:31:36 32HP4620 0097
Maintenance Safety
This section includes instructions on how to perform some important maintenance tasks. If you have basic mechanical skills, you can perform many of these tasks with the tools provided with your ATV.
Other tasks that are more difficult and require special tools are best performed by professionals. Removing the wheels should normally be handled only by a Honda technician or other qualified mechanic.
Instructions are included in this manual only to assist in emergency service.
Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this owner’s manual.
88
Servicing Your Honda
08/07/07 14:31:43 32HP4620 0098
Maintenance Safety
Important Safety Precautions
Make sure the engine is off before you begin any maintenance or repairs. This will help eliminate several potential hazards:
Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate the engine.
Burns from hot ATV parts.
Let the engine and exhaust system cool before touching.
Injury from moving parts.
Do not run the engine unless instructed to do so.
Read the instructions before you begin, and make sure you have the tools and skills required.
To reduce the possibility of a fire or explosion, be careful when working around petrol. Use only non-flammable solvent, not petrol, to clean parts. Keep cigarettes, sparks, and flames away from all fuelrelated parts.
Remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new Honda Genuine Parts or other equivalents for repair and replacement. If you have the tools and skills required for additional maintenance jobs, you can purchase an official Honda Shop
Manual.
Servicing Your Honda
89
08/07/07 14:31:50 32HP4620 0099
Maintenance Schedule
The required Maintenance Schedule that follows specifies how often you should have your ATV serviced, and what things need attention. It is essential to have your ATV serviced as scheduled to maintain safe, dependable performance and proper emission control.
The service intervals in this Maintenance Schedule are based on average riding conditions. Some items will need more frequent service if you ride in unusually wet or dusty areas or at full throttle. Consult your
Honda dealer for recommendations applicable to your individual needs and use.
Some items in the Maintenance Schedule can be performed with basic mechanical skills and hand tools. Procedures for these items are provided in this manual. Other items involve more extensive procedures and may require special training, tools, and equipment. We recommend that you have your Honda dealer perform these tasks unless you have advanced mechanical skills and the required tools and equipment.
Procedures for such items in this schedule are provided in an official
Honda Shop Manual available for purchase.
If you do not feel capable of performing a given task or need assistance, remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. If you decide to do your own maintenance, use only Honda Genuine Parts or their equivalents for repair or replacement to ensure the best quality and reliability.
90
Servicing Your Honda
08/07/07 14:31:59 32HP4620 0100
Maintenance Schedule
Perform the pre-ride inspection (page 43 ) and owner maintenance on this section at each scheduled maintenance period.
Each item on the maintenance schedule requires some mechanical
* ** knowledge. Certain items (particularly those marked and ) may require more technical information and tools. Consult your Honda dealer.
*
**
Should be serviced by your Honda dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Shop Manual.
In the interest of safety, we recommend these items be serviced only by your Honda dealer.
Summary of Maintenance Schedule Notes & Procedures:
NOTES:
1.
Service more frequently when riding in dusty areas, sand or snow.
2.
Service more frequently after riding in very wet or muddy conditions.
3.
Replace every 2 years. Replacement requires mechanical skill.
Servicing Your Honda
91
08/07/07 14:32:10 32HP4620 0101
Maintenance Schedule
Maintenance Procedures:
I: inspect and clean, adjust, lubricate, or replace, if necessary
C: clean
A: adjust
L: lubricate
R: replace
ITEMS
FUEL LINE
THROTTLE OPERATION
AIR CLEANER
FREQUENCY
WHICHEVER
COMES
FIRST
NOTE km mi
HOURS
INITIAL
MAINT.
150
100
20
NOTE 1
NOTE 2
REGULAR
MAINT. INTERVAL
1000
600
100
C
I
2000
1200
200
I
I
C
I AIR CLEANER HOUSING
DRAIN TUBE
SPARK PLUG
VALVE CLEARANCE
ENGINE OIL
ENGINE OIL FILTER
RADIATOR COOLANT
COOLING SYSTEM
NOTE 3
NOTE 2
I I
I
INITIAL=
150 km (100 mi),
20 operating hours or
I
I
1 month: R
REGULAR=
Every 1,000 km (600 mi),
100 operating hours or
12 months: R
R R
I
I
R
I
I
Refer to page
−
130
124
129
134
137
105
110
118
−
Should be serviced by your Honda dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Shop Manual.
92
Servicing Your Honda
08/07/07 14:32:21 32HP4620 0102
Maintenance Schedule
ITEMS
FREQUENCY
WHICHEVER
COMES
FIRST km
NOTE mi
HOURS
DRIVETRAIN BOOTS
REAR FINAL GEAR
CASE OIL AND
DIFFERENTIAL OIL
(TRX420FM only)
REAR FINAL GEAR CASE OIL
(TRX420TM only)
2WD/4WD SELECT
SYSTEM (TRX420FM only)
BRAKE FLUID
BRAKE SHOES WEAR
BRAKE PADS WEAR
BRAKELIGHT SWITCH
BRAKE SYSTEM
REVERSE LOCK SYSTEM
GUARDS
CLUTCH SYSTEM
SUSPENSION
SPARK ARRESTER
NUTS, BOLTS, FASTENERS
WHEELS/TYRES
TIE-ROD AND JOINT BOOTS
STEERING SHAFT HOLDER
BEARINGS
STEERING SYSTEM
NOTE 3
NOTE 1, 2
NOTE 1, 2
INITIAL
MAINT.
150
100
20
REGULAR
MAINT. INTERVAL
1000 2000
600
100
I
(R:EVERY
1200
200
I
I
2 YEARS)
I
I
I
I
I
I
I
(R:EVERY
2 YEARS)
I
I
I
I
I
I
I
C
I
I
I
I
I
I
I
C
I
I
I
I
I
I
I
I
I
I
I
Refer to page
159
114, 116
114
−
−
−
−
−
157
132
−
138
140
147
142
−
139
133
−
Should be serviced by your Honda dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Shop Manual.
In the interest of safety, we recommend these items be serviced only by your Honda dealer.
Servicing Your Honda
93
08/07/07 14:32:30 32HP4620 0103
Maintenance Record
Keeping an accurate maintenance record will help ensure that your ATV is properly maintained. Retain detailed receipts to verify the maintenance was performed. If the ATV is sold, these receipts should be transferred with the ATV to the new owner. Make sure whoever performs the maintenance completes this record. All scheduled maintenance, including the 150 km (100 mile) or 20 hours initial maintenance, is considered a normal owner operating cost and will be charged for by your dealer. Use the space under Notes to record anything you want to remind yourself about or mention to your dealer.
ODO or
HOUR
Date Performed
By:
Notes km (Miles) or hours
150 (100) or
20
1,000 (600) or
100
2,000 (1,200) or
200
3,000 (1,800) or
300
4,000 (2,400) or
400
5,000 (3,000) or
500
6,000 (3,600) or
600
7,000 (4,200) or
700
8,000 (4,800) or
800
94
Servicing Your Honda
08/07/07 14:32:35 32HP4620 0104
Maintenance Component Locations rear brake lever/ parking brake lever front brake fluid reservoir front brake lever fuel fill cap throttle lever
Servicing Your Honda
95
08/07/07 14:32:41 32HP4620 0105
Maintenance Component Locations differential oil filler cap (TRX420FM only) differential oil drain bolt (TRX420FM only) coolant reserve tank air cleaner air cleaner housing drain tube rear brakelight switch rear brake pedal front brake caliper engine oil filter
96
Servicing Your Honda
08/07/07 14:32:47 32HP4620 0106
Maintenance Component Locations spark plug owner’s manual air pressure gauge battery fuse box main fuse tool kit clutch engine oil filler cap/dipstick spark arrester engine oil drain bolt gear case oil filler cap gear case oil drain bolt
Servicing Your Honda
97
08/07/07 14:33:00 32HP4620 0107
Tool Kit cargo rack.
The tools in the kit are sufficient to perform routine maintenance and simple repairs. Any extensive work requiring additional tools should be performed by your Honda dealer.
The tool kit includes the following items: standard/Phillips screwdriver screwdriver handle
10 × 12 mm open end wrench
14 × 17 mm open end wrench spark plug wrench and handlebar pliers tool case
5 mm hex wrench
REAR
(2)
(1)
(3)
(1) tool kit
(2) storage compartment
98
Servicing Your Honda
(3) rubber strap
08/07/07 14:33:08 32HP4620 0108
Owner’s Manual Storage
Your ATV provides storage for the owner’s manual so you’ll have it
To remove the seat, see page 100 .
Be careful not to flood this area when washing your ATV.
SEAT UNDERSIDE
(1)
(4) (3)
(1) owner’s manual
(2) seat
(3) air pressure gauge
(4) plastic document bag
(2)
Servicing Your Honda
99
08/07/07 14:33:20 32HP4620 0109
Seat Removal
Refer to Saf ety Precautions on page 89 .
The seat must be removed for the air cleaner, engine oil, engine oil filter, clutch, spark plug, battery and fuse maintenance and to remove the side covers, rear fender cover and left tank side cover, to access the owner’s manual, air pressure gauge, coolant reserve tank cap and colour label.
(3) (5)
(2)
(4)
(6)
Removal
1.
2.
(1) seat latch
(2) seat
(3) front prongs
Installation
1.
2.
Press down on the seat until locks.
100
Servicing Your Honda
(4) hooks
(5) studs
(6) grommets
(1)
08/07/07 14:33:28 32HP4620 0110
Clip Removal
Removal
1.
Press down on the center pin to release the lock.
2.
Pull the clip out of the hole.
1.
2.
Installation
1.
2.
Push the bottom of the pin.
Insert the clip into the hole.
3.
Lightly press down on the center pin to lock the clip.
1.
2.
3.
Servicing Your Honda
101
08/07/07 14:33:39 32HP4620 0111
Fuel
Refer to Saf ety Precautions on page 89 .
Fuel Recommendation
type research octane number unleaded
91 (or higher)
We recommend that you use unleaded fuel because it produces fewer engine deposits and extends the life of exhaust system components.
Your engine is designed to use any petrol that has a pump octane number (R + M)/2 of 86 or higher, or a research octane number of 91 or higher. Petrol pumps at service stations normally display the pump octane number. For information on the use of Petrol Containing Alcohol, see page 209 .
Use of lower octane petrol can cause persistent ‘‘pinging’’ or ‘‘spark knock’’ (a loud rapping noise) which, if severe, can lead to engine damage. Light pinging experienced while operating under a heavy load, such as climbing a hill, is no cause for concern.
If pinging or spark knock occurs at a steady engine speed under normal load, change brands of petrol. If pinging or spark knock persists, consult your Honda dealer.
Never use stale or contaminated petrol or an oil/petrol mixture. Avoid getting dirt, dust, or water in the fuel tank.
102
Servicing Your Honda
08/07/07 14:33:51 32HP4620 0112
Fuel
Fuel Capacity
Fuel tank capacity, including reserve:
13.3
(3.51 US gal , 2.93 Imp gal)
Reserve capacity:
2.6
(0.69 US gal , 0.57 Imp gal)
The tank should be refilled as soon as possible after switching to reserve, and the fuel valve should be returned to the ON position after refueling to avoid running out of fuel with no reserve.
Refueling Procedure
Refer to Saf ety Precautions on page 89 .
(3) (2)
(1)
(4)
(1) fuel fill cap
(2) breather tube
(3) handlebar cover hole
(4) filler neck
Servicing Your Honda
103
08/07/07 14:34:00 32HP4620 0113
Fuel
1.
2.
3.
Avoid over filling the tank. There should be no fuel in the filler neck.
Petrol is highly flammable and explosive. You can be burned or seriously injured when handling fuel.
Stop the engine and keep heat, sparks and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.
4.
After refueling, turn the fuel fill cap clockwise until it clicks.
5.
Insert the breather tube into the handlebar cover hole.
6.
If the fuel valve was set to RES, turn the fuel valve ON.
If you replace the fuel fill cap, use only a Honda Genuine replacement part.
104
Servicing Your Honda
08/07/07 14:34:05 32HP4620 0114
Engine Oil & Filter
Engine oil quality is a major factor that affects both the performance and the service life of the engine.
Using the proper oil (page 106 ) and filter, and regularly checking, adding, and changing oil will help extend your engine’s life. Even the best oil wears out. Changing oil helps get rid of dirt and deposits in the engine. Operating the engine with old or dirty oil can damage your engine. Running the engine with insufficient oil can cause serious damage to the engine and transmission.
Change the engine oil as specified in the maintenance schedule on page 92 . When running in very dusty conditions, oil changes should be performed more frequently than specified in the maintenance schedule.
Servicing Your Honda
105
08/07/07 14:34:17 32HP4620 0115
Engine Oil & Filter
Oil Recommendation
API classification * viscosity (weight) suggested oil
SE, SF or SG
SAE 10W-40
Honda 4-stroke oil or an equivalent
* Motor oils intended for Service SE, SF or SG will show this designation on the container.
Your ATV does not need oil additives. Use the recommended oil.
Do not use oils with graphite or molybdenum additives. They may adversely affect clutch operation.
Do not use API SH or higher oils displaying a circular API ‘‘energy conserving’’ service label on the container. They may affect lubrication and clutch performance.
NOT RECOMMENDED OK
Do not use non-detergent, vegetable, or castor based racing oils.
106
Servicing Your Honda
08/07/07 14:34:26 32HP4620 0116
Engine Oil & Filter
Other viscosities shown in the following chart may be used when the average temperature in your riding area is within the indicated range.
JASO T 903 standard
The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines.
There are two classes: MA and MB.
Oil conforming to the standard is labeled on the oil container. For example, the following label shows the MA classification.
(1)
(2)
(1) code number of the sales company of the oil
(2) oil classification
Servicing Your Honda
107
08/07/07 14:34:34 32HP4620 0117
Engine Oil & Filter
Checking & Adding Oil
Refer to Saf ety Precautions on page 89 .
Check the engine oil level each day before operating your ATV and add if needed.
Bef ore riding your ATV, check the engine oil level.
1.
Park your ATV on a firm, level surface.
2.
Start the engine in a well-ventilated area and let it idle for 3 − 5
3.
minutes. Stop the engine and wait 2 − 3 minutes.
Remove the seat (page 100 ).
4.
LEFT SIDE
(1)
(1) left side cover
108
Servicing Your Honda
08/07/07 14:34:45 32HP4620 0118
Engine Oil & Filter
5.
wipe it clean.
6.
Insert the oil filler cap/dipstick without screwing it in, then remove the oil filler cap/dipstick and check the oil level. The oil level should
7.
the oil filler cap/dipstick.
If required, add the specified oil into the filler cap hole, up to the upper level mark on the oil filler cap/dipstick. Do not overfill.
8.
Reinstall the oil filler cap/dipstick.
9.
Install the left side cover.
10.
Install the seat.
Running the engine with an improper oil level can cause serious engine damage.
LEFT SIDE
(2)
(2) oil filler cap/dipstick
(3)
(4)
(3) upper level mark
(4) lower level mark
Servicing Your Honda
109
08/07/07 14:34:57 32HP4620 0119
Engine Oil & Filter
Changing Engine Oil & Filter
Refer to Saf ety Precautions on page 89 .
Your ATV’s oil filter has very specific performance requirements. Use a new Honda Genuine oil filter specified for your model or a filter of equal quality.
Using the wrong oil f ilter may result in leaks or engine damage.
This procedure requires mechanical skill and professional tools such as a torque wrench and oil filter wrench, as well as a means for disposing of the drained fluid (page 180 ). If you do not have the skills or the tools, see your Honda dealer.
Drain the Engine Oil:
1.
With the ATV on the level ground, remove the seat (page side cover (page crankcase.
108
100 ), left
) and the oil filler cap/dipstick from the front
2.
Place an oil drain pan under the crankcase and remove the engine oil
UNDER ENGINE
(1) engine oil drain plug
110
Servicing Your Honda
(2)
(1)
(2) sealing washer
08/07/07 14:35:05 32HP4620 0120
Install a New Engine Oil Filter:
1.
Remove the seat (page 100 ).
2.
RIGHT SIDE
Engine Oil & Filter
(1) right side cover
(1)
(cont’d)
Servicing Your Honda
111
08/07/07 14:35:15 32HP4620 0121
Engine Oil & Filter
3.
4.
manner (page 180 ).
then install a new oil filter. Use only the Honda Genuine oil filter or a filter of equivalent quality specified for your model. Using the wrong
Honda filter or a non-Honda filter which is not of equivalent quality may cause engine damage.
5.
on the filter body, near the seal.
Improper installation of the oil f ilter can cause serious engine damage.
RIGHT SIDE
(4) (8) (5)
(6)
(2)
(3)
(2) oil filter cover
(3) bolts
(4) oil filter
(5) O-rings
112
Servicing Your Honda
(7)
(2)
(3)
(6) spring
(7) rubber seal
(8) ‘‘OUTSIDE’’ mark
08/07/07 14:35:32 32HP4620 0122
Engine Oil & Filter
6.
Reinstall the oil filter cover, making sure the bolts are tightened to the specified torque:
10 N·m (1.0 kgf·m , 7 lbf·ft)
7.
Pour the drained oil into a suitable container and dispose of it in an approved manner (page 180 ).
Improper disposal of drained f luids is harmf ul to the environment.
8.
Install the right side cover.
Add Engine Oil:
1.
Check that the drain plug sealing washer is in good condition. If necessary, replace the sealing washer.
2.
Reinstall the oil drain plug and tighten it to the specified torque:
25 N·m (2.5 kgf·m , 18 lbf·ft)
3.
Fill the crankcase with the recommended grade oil approximately:
2.8
(3.0 US qt , 2.5 Imp qt)
4.
Reinstall the oil filler cap/dipstick.
5.
6.
Start the engine and let it idle for 3 − 5 minutes.
Stop the engine, wait 2 − 3 minutes and check the oil level. Make sure the oil is between the upper and lower level marks on the oil filler cap/dipstick. If necessary, add more oil but do not overfill.
7.
Check that there are no oil leaks.
8.
9.
Install the left side cover.
Install the seat.
If a torque wrench is not used for installation, see your Honda dealer as soon as possible to verify proper assembly.
Servicing Your Honda
113
08/07/07 14:35:40 32HP4620 0123
Gear Case Oil
Oil Recommendation
type viscosity (weight)
Changing Oil
hypoid gear oil
SAE 80
Refer to Saf ety Precautions on page 89 .
Change the oil with the gear case at normal operating temperature to assure complete and rapid draining.
114
Servicing Your Honda
08/07/07 14:35:54 32HP4620 0124
Gear Case Oil
1.
Park the ATV on level ground.
2.
3.
Check that the drain plug sealing washer is in good condition. If necessary, replace the sealing washer.
4.
After the oil has completely drained, reinstall the drain plug and tighten it to the specified torque:
12 N·m (1.2 kgf·m , 9 lbf·ft)
5.
Pour the drained oil into a suitable container and dispose of it in an approved manner (page 180 ).
Improper disposal of drained f luids is harmf ul to the environment.
6.
Fill the gear case with the recommended oil.
75 cm (2.5 US oz , 2.6 Imp oz)
7.
8.
Install the oil filler cap and oil level check bolt.
REAR
(2)
(4)
(3)
(1) oil drain plug
(2) oil filler cap
(1)
(3) oil level check bolt
(4) oil level check hole
Servicing Your Honda
115
08/07/07 14:36:03 32HP4620 0125
Differential Oil (TRX420FM only)
Oil Recommendation
type viscosity (weight)
Changing Oil
hypoid gear oil
SAE 80
Refer to Saf ety Precautions on page 89 .
Change the oil with the differential at normal operating temperature to assure complete and rapid draining.
116
Servicing Your Honda
08/07/07 14:36:13 32HP4620 0126
Differential Oil (TRX420FM only)
1.
Park the ATV on level ground.
2.
3.
Check that the drain plug sealing washer is in good condition. If necessary, replace the sealing washer.
4.
After the oil has completely drained, reinstall the drain plug and tighten it to the specified torque:
12 N·m (1.2 kgf·m , 9 lbf·ft)
5.
Pour the drained oil into a suitable container and dispose of it in an approved manner (page 180 ).
Improper disposal of drained f luids is harmf ul to the environment.
6.
Fill the differential with the recommended oil.
230 cm (7.8 US oz , 8.1 Imp oz)
Make sure the oil level is at the lower edge of the oil filler inspection
7.
Install the oil filler cap.
FRONT
(3)
(2)
(1)
(1) oil drain plug
(2) oil filler cap
(1)
(3) oil filler inspection hole
Servicing Your Honda
117
08/07/07 14:36:22 32HP4620 0127
Coolant
Your ATV’s liquid cooling system dissipates engine heat through the coolant jacket that surrounds the cylinder and cylinder head.
Maintaining the coolant will allow the cooling system to work properly and prevent freezing, overheating, and corrosion.
Coolant Recommendation
Use Pro Honda HP coolant or an equivalent high quality ethylene glycol antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines. Check the antifreeze container label.
Use only distilled water as a part of the coolant solution. Water that is high in mineral content or salt may be harmful to the aluminum engine.
Using coolant with silicate inhibitors may cause premature wear of water pump seals or blockage of radiator passages. Using tap water may cause engine damage.
The factory provides a 50/50 solution of antifreeze and water in this
ATV. This coolant solution is recommended for most operating temperatures and provides good corrosion protection.
Decreasing the concentration of antifreeze to less than 40% will not provide proper corrosion protection.
118
Servicing Your Honda
08/07/07 14:36:33 32HP4620 0128
Coolant
Increasing the concentration of antifreeze is not recommended because it decreases cooling system performance. Higher concentrations of antifreeze (up to 60%) should only be used to provide additional protection against freezing. Check the cooling system frequently during freezing weather.
Checking & Adding Coolant
Refer to Saf ety Precautions on page 89 .
Check the engine coolant level each day before operating your ATV and add if needed.
RIGHT REAR
(2)
(1) (3)
(1) reserve tank
(2) UPPER level mark
(3) LOWER level mark
1.
Make sure the vehicle is on level ground.
2.
With the engine at normal operating temperature, check the coolant
2
If the reserve tank is empty, or if coolant loss is excessive, check for leaks and see your Honda dealer for repair.
(cont’d)
Servicing Your Honda
119
08/07/07 14:36:45 32HP4620 0129
Coolant
3.
4.
Remove the seat (page 100 ).
5.
Always add coolant to the reserve tank. Do not attempt to add coolant by removing the radiator cap.
6.
Add coolant to the reserve tank as required to bring the coolant level to the UPPER level mark.
REAR
(5)
(4)
(6)
(4) rubber strap
(5) rear fender cover
(6) reserve tank cap
7.
After adding coolant, install the reserve tank cap and rear fender cover.
8.
Fasten the rubber strap.
9.
Install the seat.
120
Servicing Your Honda
08/07/07 14:36:52 32HP4620 0130
Coolant
Coolant Replacement
Refer to Saf ety Precautions on page 89 .
Coolant should be replaced by your Honda dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Shop Manual.
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
To properly dispose of drained coolant, refer to You & the Environment, page 180 .
Improper disposal of drained f luids is harmf ul to the environment.
Servicing Your Honda
121
08/07/07 14:37:05 32HP4620 0131
Coolant
Radiator Core
Refer to Saf ety Precautions on page 89 .
Check the air passages for clogging or damage. Remove insects, mud, or any obstruction with low water pressure. Have the radiator checked by your Honda dealer if the air flow is restricted over more than 20% of the radiator surface.
Clean the radiator core after riding the ATV in mud.
To clean the radiator core and radiator grill plate:
1.
2.
3.
Remove the clips ( ) (page 101 4
2
Do not apply pressured water directly to the radiator core. The pressured water can damage the radiator core.
FRONT
(6)
(3)
(5)
(4)
(1)
(2)
(1) tabs A
(2) radiator grill under cover
(3) clips
(4)
(4) radiator grill covers
(5) tabs B
(6) couplers
122
Servicing Your Honda
08/07/07 14:37:11 32HP4620 0132
4.
5.
6.
Install the removed parts in reverse order of removal.
FRONT
Coolant
(7)
(7) radiator grill plate (8) radiator core
(8)
Servicing Your Honda
123
08/07/07 14:37:20 32HP4620 0133
Air Cleaner
Refer to Saf ety Precautions on page 89 .
Proper air cleaner maintenance is very important for off-road vehicles.
A dirty, water-soaked, worn-out, or defective air cleaner will allow dirt, dust, mud, and other impurities to pass into the engine.
Service the air cleaner more frequently if you ride in unusually wet or dusty areas. Your Honda dealer can help you determine the correct service interval for your riding conditions.
Your ATV’s air cleaner has very specific performance requirements.
Use a new Honda Genuine air cleaner specified for your model or an air cleaner of equal quality.
Using the wrong air cleaner may result in premature engine wear.
Proper air cleaner maintenance can prevent premature engine wear or damage, expensive repairs, low engine power, poor gas mileage, and spark plug fouling.
Improper or lack of proper air cleaner maintenance can cause poor perf ormance and premature engine wear.
124
Servicing Your Honda
08/07/07 14:37:28 32HP4620 0134
Air Cleaner
Cleaning
1.
Remove the seat (page 100 ).
UNDER SEAT
(1)
2.
3.
(1) retainer clips
(2)
(2) air cleaner housing cover
(cont’d)
Servicing Your Honda
125
08/07/07 14:37:38 32HP4620 0135
Air Cleaner
4.
the air cleaner housing.
5.
6.
Remove the air cleaner ( ) from the air cleaner body ( 7 ).
7.
Gently wash the air cleaner in clean, non-flammable (high flash point) solvent such as kerosene − not petrol. After cleaning, gently squeeze out the remaining solvent. Avoid twisting or wringing the air cleaner. This can tear the foam.
8.
Inspect for tears or cracks in the foam or seams of the air cleaner.
Replace the air cleaner if it is damaged.
9.
Allow the air cleaner to dry thoroughly before applying oil. A wet air cleaner will not fully absorb the oil.
10.
Pour clean air filter oil over the entire surface of the air cleaner. Use both hands to evenly spread the oil into the air cleaner. Gently squeeze out any excess oil. (To keep your hands dry, place the air cleaner in a clean plastic bag before spreading the oil into the air cleaner.)
UNDER SEAT
(7) (3) (4)
(3)
(5)
(6)
(3) screw
(4) air cleaner assembly
(5) clamp
126
Servicing Your Honda
(6) air cleaner
(7) air cleaner body
08/07/07 14:37:46 32HP4620 0136
Air Cleaner
11.
12.
Install the air cleaner on the air cleaner body.
Apply a thin coat of grease to the sealing surface of the air cleaner assembly.
13.
Install the clamp.
14.
Insert the air cleaner assembly into the air cleaner housing.
15.
16.
Fasten the screw.
Reassemble by reversing the disassembly sequence.
Install the air cleaner housing cover with the FRONT mark ( 8 ) facing forward and fit the cut out of the tab ( 9 ) at the end of the air cleaner.
UNDER SEAT
(8) (9)
(9)
(8) FRONT mark (9) tab
Servicing Your Honda
127
08/07/07 14:37:53 32HP4620 0137
Air Cleaner
Dust Cover
UNDER SEAT
(1) (2)
(1) dust cover
If the dust cover is dirty, clean it.
(2) breather joint
128
Servicing Your Honda
08/07/07 14:38:01 32HP4620 0138
Air Cleaner
Air Cleaner Housing Drain Tube
The air cleaner housing drain tube should be serviced in accordance with the Maintenance Schedule. (Riding through water may require more frequent inspection.) If deposits can be seen in the drain tube, the tube must be cleaned before starting the vehicle.
REAR
(2)
(3)
(1)
(1) drain tube
(2) clip
(3) air cleaner housing
1.
2.
Drain the deposits.
3.
Reinstall the drain tube, securing it with the clip.
Servicing Your Honda
129
08/07/07 14:38:11 32HP4620 0139
Throttle
Throttle Freeplay
Refer to Saf ety Precautions on page 89 .
RIGHT HANDLEBAR
( A )
(B)
3 − 8 mm
(0.1
− 0.3 in)
(2) (3) (4) (1)
(1) throttle lever
(2) rubber sleeve
(3) throttle cable adjuster
(4) lock nut
(A) decrease freeplay
(B) increase freeplay
Inspection
Freeplay:
3 − 8 mm (0.1
− 0.3 in)
Adjustment
1.
2.
3.
Turn the adjuster to obtain the correct freeplay.
4.
Tighten the lock nut and reinstall the sleeve.
5.
After adjustment, check for smooth operation of the throttle lever from fully closed to fully open in all steering positions.
130
Servicing Your Honda
08/07/07 14:38:20 32HP4620 0140
Throttle
Throttle Inspection
Refer to Saf ety Precautions on page 89 .
1.
Check that the throttle assembly is positioned properly and the securing bolts are tight.
2.
Check for smooth operation of the throttle lever from fully open to fully closed in all steering positions. If there is a problem, see your
Honda dealer.
3.
Inspect the condition of the throttle cable from the throttle lever down to the throttle body. If the cable is kinked or chafed, have it replaced.
4.
Check the throttle cable for tension or stress in all steering positions.
5.
Lubricate the throttle cable with a commercially available cable lubricant to prevent premature wear and corrosion.
Servicing Your Honda
131
08/07/07 14:38:32 32HP4620 0141
Clutch System
Your ATV’s shift-activated, wet, multiplate clutch is part of the primary drive system. Proper adjustment allows a smooth, gradual engagement when shifting gears.
Clutch Adjustment
Refer to Saf ety Precautions on page 89 .
LEFT FRONT
(1)
(1) lock nut
(2)
(2) clutch adjuster
1.
2.
Make sure the engine is cool.
Make sure the ignition switch is OFF ( ).
3.
Remove the seat (page 100 ) and left side cover (page 108 ).
4.
5.
6.
resistance.
Turn the adjuster 1/4 turn clockwise, then tighten the lock nut to hold the adjuster in this position.
7.
After adjustment, start the engine and test ride your ATV to be sure the clutch is operating properly.
8.
Install the removed parts in reverse order of removal.
If you cannot get proper adjustment, or the clutch does not work properly, the clutch friction discs may be worn. See your Honda dealer or refer to official Honda Shop Manual.
132
Servicing Your Honda
08/07/07 14:38:41 32HP4620 0142
Reverse Lock System
Reverse Lock System Adjustment
Refer to Saf ety Precautions on page 89 .
LEFT HANDLEBAR
(1)
(6)
2 − 4 mm
(0.1
− 0.2 in)
(2) (3)
(4) (5)
(1) dust cover
(2) reverse assist lever
(3) rear brake lever
1.
2.
3.
2 − 4 mm (0.1
− 0.2 in)
(4) rubber sleeve
(5) lock nut
(6) adjusting nut
After adjustment, tighten the lock nut securely.
4.
Return the dust cover and rubber sleeve.
Other Checks
Check the reverse assist lever and cable for loose connections or other damage. If the cable is worn or kinked, have it replaced by your Honda dealer.
Servicing Your Honda
133
08/07/07 14:38:53 32HP4620 0143
Spark Plug
Spark Plug Recommendation
standard spark plug BKR5E-11 (NGK) or
K16PR-U11 (DENSO)
Use only the recommended type of spark plug in the recommended heat range.
Using spark plugs with an improper heat range can cause engine damage.
Spark Plug Inspection & Replacement
Refer to Saf ety Precautions on page 89 .
1.
Remove the seat (page 100 ) and left side cover (page 108 ).
2.
LEFT SIDE
(1)
(2)
(1) left tank side cover
134
Servicing Your Honda
(2) bolts
08/07/07 14:39:06 32HP4620 0144
Spark Plug
3.
4.
Clean any dirt from around the spark plug base.
spark plug wire when disconnecting the cap.
5.
Using a spark plug wrench provided in the tool kit, remove the spark plug.
6.
Inspect the electrodes and centre porcelain for deposits, corrosion, or carbon fouling. If the corrosion or deposits are heavy, replace the plug. Clean a carbon or wet-fouled plug with a plug cleaner, if available, or a wire brush. Inspect the spark plug electrodes for wear.
insulator tip appear unusually fouled or burned, we suggest that you contact your Honda dealer.
7.
Discard the spark plug if there is apparent wear or if the insulator is cracked or chipped.
8.
adjustment is necessary, bend the side electrode carefully.
The gap should be:
1.00
− 1.10 mm (0.039
− 0.043 in)
LEFT SIDE 1.00
− 1.10 mm
(0.039
− 0.043 in)
(6)
(5)
(4)
(3)
(3) spark plug cap
(4) centre electrode
(5) side electrode
(6) spark plug gap
(cont’d)
Servicing Your Honda
135
08/07/07 14:39:15 32HP4620 0145
Spark Plug
9.
With the plug washer attached, thread the spark plug in by hand to prevent cross-threading.
10.
Tighten the spark plug:
If the old plug is good:
1/8 turn after it seats.
If installing a new plug, tighten it twice to prevent loosening: a) First, tighten the plug:
NGK:
DENSO:
3/4
1/2 turn after it seats.
turn after it seats.
b) Then loosen the plug.
c) Next, tighten the plug again:
1/8 turn after it seats.
An improperly tightened spark plug can damage the engine. If a plug is too loose, a piston may be damaged. If a plug is too tight, the threads may be damaged.
11.
Connect the spark plug cap. Take care to avoid pinching any cables or
12.
wires.
Install the remaining parts in the reverse order of removal.
136
Servicing Your Honda
08/07/07 14:39:23 32HP4620 0146
Valves
Valve Inspection
Refer to Saf ety Precautions on page 89 .
Valve clearance should be: intake: 0.15 mm (0.006 in) exhaust: 0.23 mm (0.009 in)
Excessive clearance will cause noise. Insufficient clearance will cause loss of power and possibly damage the valves.
For those who are mechanically proficient and have the proper tools, instructions on adjusting valve clearances are given in the official
Honda Shop Manual. Otherwise, the valves should be adjusted by your
Honda dealer.
Servicing Your Honda
137
08/07/07 14:39:32 32HP4620 0147
Spark Arrester
Refer to Saf ety Precautions on page 89 .
The exhaust system must be periodically purged of accumulated carbon.
To purge the system:
REAR
(1)
(1) bolt
1.
Select a well-ventilated area free of combustible materials and make sure the exhaust pipe is cool.
2.
3.
Start the engine and rev it up approximately twenty times while momentarily creating exhaust system back pressure by blocking the
4.
end of the muffler with a shop towel.
Stop the engine and allow the exhaust pipe to cool.
5.
Reinstall the bolt securely.
138
Servicing Your Honda
08/07/07 14:39:44 32HP4620 0148
Brakes
The hydraulic disc brakes (front) and single mechanical drum brake
(rear) on your ATV dissipate heat generated by the friction of the brake pads on the disc (front) and the brake shoes on the drums (rear) as the wheels are slowed.
Hydraulic Disc Front Brake
As the front brake pads wear, brake fluid level will drop. A leak in the system will also cause the level to drop.
There are no adjustments to perform, but fluid level and pad wear must be inspected periodically. The system must be inspected frequently to ensure there are no fluid leaks.
If the right brake lever freeplay does not feel within the normal range while riding, check the brake pads for wear (page 142 ).
Worn pads should be replaced. If the pads are not worn beyond the recommended limit, there is probably air in the brake system. See your
Honda dealer to have the air bled from the system.
Mechanical Drum Rear Brake
If the rear brake lever/parking brake lever or brake pedal freeplay does not feel within the normal range while riding, check the brake shoes for wear (page 147 ).
Brake Fluid Recommendation
brake fluid DOT 4 Brake Fluid
The recommended brake fluid is DOT 4 Brake Fluid, or any brake fluid of equal quality and performance. Use fresh brake fluid from a sealed container. Be sure to read the label before opening the sealed container.
An opened container may be contaminated or may have absorbed moisture from the air.
Servicing Your Honda
139
08/07/07 14:39:54 32HP4620 0149
Brakes
Fluid Level Inspection
Refer to Saf ety Precautions on page 89 .
If your inspection indicates a low fluid level, have your Honda dealer add the recommended fluid.
Do not add or replace brake fluid, except in an emergency. If you do add fluid, have your Honda dealer check the system as soon as possible.
Brake f luid can damage plastic and painted surf aces. Handle with care.
Wipe up spills immediately. Avoid brake fluid contact with skin or eyes.
If it comes in contact with your eyes, wash them out with clean water and immediately call a doctor. If it comes in contact with your skin, wash with clean water and, if necessary, call a doctor.
RIGHT HANDLEBAR
(1)
(1) LOWER level mark
With the ATV in an upright position, check the fluid level.
below the LOWER level mark, check the brake pads for wear
(page 142 ).
140
Servicing Your Honda
08/07/07 14:40:00 32HP4620 0150
Brakes
Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks.
Other Inspections
Make sure there are no fluid leaks.
Check for deterioration or cracks in the hoses and fittings. If the hoses are worn or cracked, have them replaced by your Honda dealer.
Servicing Your Honda
141
08/07/07 14:40:08 32HP4620 0151
Brakes
Brake Pad Wear
Refer to Saf ety Precautions on page 89 .
Brake pad wear will depend upon the severity of usage and riding conditions. The pads will wear faster in wet or muddy conditions.
Inspect the pads visually during all regular service intervals to determine the pad wear.
RIGHT FRONT (Left side similar)
(2)
(1)
(1) wear indicator (2) edge of reference mark dealer for this replacement.
Always inspect both pads in both the right and left front brake calipers.
142
Servicing Your Honda
08/07/07 14:40:15 32HP4620 0152
Brakes
Rear Brake Pedal Freeplay
RIGHT SIDE
(1)
15 − 20 mm
(0.6
− 0.8 in)
(1) rear brake pedal
Inspection starts to take hold. Freeplay, measurement at the tip of the end of the pedal, should be:
15 − 20 mm (0.6
− 0.8 in)
If necessary, adjust to the specified range.
Servicing Your Honda
143
08/07/07 14:40:24 32HP4620 0153
Brakes
Adjustment
RIGHT REAR
(2)
(3)
(2) brake pedal adjusting nut
(3) brake arm pin
1.
rod at the rear of the frame. Make sure the cutout on the adjusting nut
2.
then check the clearance between the brake arm and the brake arm pin.
(4) brake arm
144
Servicing Your Honda
(4)
08/07/07 14:40:30 32HP4620 0154
Brakes
Rear Brake Lever Freeplay
LEFT HANDLEBAR
(1)
15 − 20 mm
(0.6
− 0.8 in)
(1) rear brake lever/parking brake lever
Inspection before the brake starts to take hold. Freeplay (measurement at the tip of the end of the brake lever) should be:
15 − 20 mm (0.6
− 0.8 in)
If necessary, adjust to the specified range.
Servicing Your Honda
145
08/07/07 14:40:39 32HP4620 0155
Brakes
Adjustment
RIGHT REAR (3)
(2)
(2) brake lever adjusting nut
(3) brake arm pin
Adjust the freeplay of the rear brake lever/parking brake lever with the front wheels pointed straight ahead.
1.
rod at the rear of the frame. Make sure the cutout on the adjusting nut
2.
Adjust the freeplay of the rear brake lever/parking brake lever. Push and the brake arm pin.
(4) brake arm
146
Servicing Your Honda
(4)
08/07/07 14:40:51 32HP4620 0156
Brakes
Other Inspections
Check that the brake lever and brake pedal assemblies are positioned properly and the securing bolts are tight.
Make sure that the brake cables, brake arm, spring, parking, and fasteners are in good condition.
Brake Shoe Wear
Refer to Saf ety Precautions on page 89 .
The rear brake is equipped with an external brake wear indicator that lets you check brake wear without disassembly. Application of the brake control causes the arrow on the brake arm to move toward a reference mark on the brake panel.
RIGHT REAR
(2)
(1) arrow
(2) brake arm
(1) (3)
(3) reference mark
1.
2.
Replace the brake shoe if the arrow aligns with the reference mark replacement is necessary, see your Honda dealer.
Servicing Your Honda
147
08/07/07 14:41:00 32HP4620 0157
Brakes
Brakelight Switch Adjustment
Refer to Saf ety Precautions on page 89 .
Rear Brake Only: behind the engine from time to time. The brakelight should turn on at 15 mm (0.6 in) of pedal stroke. See Rear Brake Pedal Freeplay , page 143 .
switch operates too soon.
RIGHT REAR
(1)
( B )
( A )
(2)
(1) rear brakelight switch
(2) adjusting nut
148
Servicing Your Honda
08/07/07 14:41:08 32HP4620 0158
Brakes
Draining Water from Brakes
Refer to Saf ety Precautions on page 89 .
RIGHT REAR
(1)
(1) rear brake drain bolt
1.
Make sure the engine is OFF and the parking brake is set.
2.
brake panel.
If any water drains, the brake seals must be replaced by your Honda dealer as soon as possible.
Servicing Your Honda
149
08/07/07 14:41:13 32HP4620 0159
Tyres
To safely operate your ATV, your tyres must be the proper type and size, in good condition with adequate tread, and correctly inflated.
Using tyres that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tyre inflation and maintenance.
This ATV is equipped with low pressure tubeless tyres. Although the tyres are designed specifically for off-road use, they are not immune to punctures. Always select your riding area with care.
The following pages give detailed information on how and when to check your air pressure, how to inspect your tyres for wear and damage, and our recommendations for tyre repair and replacement.
150
Servicing Your Honda
08/07/07 14:41:20 32HP4620 0160
Tyres
Air Pressure
Refer to Saf ety Precautions on page 89 .
Properly inflated tyres provide the best combination of handling, tread life, and riding comfort. Generally, underinflated tyres wear unevenly, adversely affect handling, and are more likely to fail from being overheated. Overinflated tyres make your ATV ride harshly, are more prone to damage from surface hazards, and wear unevenly.
Make sure the air valve caps are secure. If necessary, install new caps.
Servicing Your Honda
151
08/07/07 14:41:27 32HP4620 0161
Tyres
Always check air pressure when your tyres are ‘‘cold.’’ If you check air pressure when your tyres are ‘‘warm’’ − even if your ATV has only been ridden for a few miles − the readings will be higher. If you let air out of warm tyres to match the recommended cold tyre pressures, the tyres will be underinflated. Be sure to check tyre pressure at the riding site, since changes in altitude can affect air pressure.
The recommended ‘‘cold’’ tyre pressures are: tyre pressure, front & rear (cold) front rear
25.0 kPa (3.6 psi)
25.0 kPa (3.6 psi)
152
Servicing Your Honda
08/07/07 14:41:36 32HP4620 0162
Tyres
A manually operated tyre pump should be used rather than the high pressure system found in service stations. This will minimize the possibility of tyre damage from overinflation. If you use a high pressure system at a service station, add air in small amounts and check the pressure increase frequently to prevent possible tyre damage from overinflation.
Operating this ATV with improper tyres, or with uneven tyre pressure may cause loss of control, and you could be seriously injured or killed.
Always use the size and type tyres specified in this owner’s manual for this vehicle.
Always maintain proper tyre pressure as described in this owner’s manual.
Inspection
Refer to Saf ety Precautions on page 89 .
Whenever you check the tyre pressures, you should also look for:
Bumps or bulges in the side of the tyre or the tread. Replace any tyre that has a bump or bulge.
Cuts, slits, or cracks in the tyres. Replace the tyre if you can see fabric or cord.
Nails or other foreign objects embedded in the side of the tyre or tread.
Excessive tread wear.
Servicing Your Honda
153
08/07/07 14:41:47 32HP4620 0163
Tyres
Also, if you hit a pothole or other hard object while riding, stop as soon as you safely can and carefully inspect the tyres for damage.
Tread Wear
FRONT NEW
REAR
(2)
Replace
4 mm
(0.16 in)
Replace
4 mm
(0.16 in)
(1) (3)
NEW
(1) groove depth
(2) wear indicator
(3) wear indicator location mark
For best performance, you should replace a tyre before the tread depth at the centre reaches the following limits: front rear
4 mm (0.16 in)
4 mm (0.16 in)
154
Servicing Your Honda
08/07/07 14:41:55 32HP4620 0164
Tyres
Tyre Repair
Refer to Saf ety Precautions on page 89 .
A tyre that is repaired, either temporarily or permanently, will have lower speed and performance limits than a new or undamaged tyre.
A temporary repair can sometimes be made in an emergency situation.
However, since a temporary repair may not hold, you must ride very slowly, preferably without any cargo, and have the tyre replaced or permanently repaired as soon as possible. (For more information on temporary repairs, see If You Have a Flat Tyre, page 187 .)
A permanent repair, such as an internal plug patch, can be made if a tyre has only a small puncture in the tread area. However you may not be able to safely carry as much weight. If you choose to have a tyre repaired, be sure the repair work is performed by a professional.
If you have a tyre professionally repaired at a non-Honda facility, we recommend that you have the work checked by your Honda dealer.
Servicing Your Honda
155
08/07/07 14:42:08 32HP4620 0165
Tyres
Tyre Replacement
Refer to Saf ety Precautions on page 89 .
The tyres that came on your ATV were designed to match the performance capabilities of your ATV and provide the best combination of handling, braking, and comfort.
It is best to replace all four tyres, however if that is not possible, you must replace the tyres in pairs (front or rear) with tyres of the same size and type as the originals. Never replace just one tyre.
Installing improper tyres on your ATV can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tyres recommended in this owner’s manual.
The recommended tyres for your ATV are: front rear
AT24 × 8-12
AT24 × 10-11
★★ MAXXIS M977
★★ MAXXIS M978
When you replace a tyre, remember:
Have the tyre replaced by your Honda dealer if possible.
If you have a tyre professionally replaced at a non-Honda facility, we recommended that you have the work checked by your Honda dealer.
156
Servicing Your Honda
08/07/07 14:42:16 32HP4620 0166
Guards
Skid Plate & Engine Guard
Refer to Saf ety Precautions on page 89 .
(1)
(2) skid plate
(2)
(1) engine guard plate for cracks, damage or looseness at intervals shown in the
Maintenance Schedule.
Have the engine guard and skid plate replaced if they are cracked or damaged. If the guard and plate bolts are loose, tighten them securely.
Servicing Your Honda
157
08/07/07 14:42:23 32HP4620 0167
Guards
Front Boot Guards & Front Driveshaft Guards
(TRX420FM only)
Refer to Saf ety Precautions on page 89 .
(1) front boot guards
(2) (1) (2)
(2) front driveshaft guards cracks, damage or looseness.
Tighten any loose fasteners. Replace the front boot guards and front driveshaft guards as required.
158
Servicing Your Honda
08/07/07 14:42:30 32HP4620 0168
Drivetrain Boots
Propeller Shaft Boots & Yoke Joint Boot
Refer to Saf ety Precautions on page 89 .
(1) (2)
(1) rubber propeller shaft boots (TRX420FM only)
(2) rubber yoke joint boot replace them.
Servicing Your Honda
159
08/07/07 14:42:37 32HP4620 0169
Drivetrain Boots
Driveshaft Boots (TRX420FM only)
Refer to Saf ety Precautions on page 89 .
FRONT
(1)
(1) rubber driveshaft boots necessary, have your Honda dealer replace them.
160
Servicing Your Honda
08/07/07 14:42:46 32HP4620 0170
Battery
Your ATV has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water as you would with a conventional-type battery.
Your battery is a maintenance-f ree type and can be permanently damaged if the cap strip is removed.
Electrical accessories use current from the battery, even when the ignition is OFF. Limited operation also allows the battery to discharge.
If you have electrical accessories on your ATV or do not ride frequently, we recommend that you charge the battery frequently (see Battery
Charging, page 165 ).
If you do not expect to ride your ATV for at least two weeks, we recommend you remove the battery, or at least disconnect the battery cables (negative cable first).
If you plan to store your ATV, see Battery Storage, page 162 .
If your battery seems weak and/or is leaking electrolyte (causing slow starting or other electrical problems), see your Honda dealer.
This symbol on the battery means that this product must not be treated as household waste.
An improperly disposed of battery can be harmf ul to the environment and human health.
Always conf irm local regulations f or battery disposal.
Servicing Your Honda
161
08/07/07 14:42:55 32HP4620 0171
Battery
Battery Storage
Refer to Saf ety Precautions on page 89 .
If you plan to store your ATV, we recommend you remove the battery and store it where it can be charged at least every 30 days to maintain its service life.
If you do not remove the battery, we recommend disconnecting the battery cables (negative cable first).
You will get the best storage results from removing the battery and slow
(trickle) charging it every 30 days (see Battery Charging, page 165 ).
Before you remove the battery, be sure to read all the information that follows, as well as the information on the battery label.
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.
Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.
162
Servicing Your Honda
08/07/07 14:43:07 32HP4620 0172
The battery is located in a compartment under the seat.
UNDER SEAT
(1)
Battery
(3)
(4)
(2)
(1) rubber band
(2) negative ( − ) terminal lead
(3) battery
(4) positive ( + ) terminal lead
Removal
1.
Make sure the ignition switch is OFF ( ).
2.
Remove the seat (page 100 ).
3.
4.
Remove the rear fender cover (page 120 ).
5.
Disconnect the negative ( − 2 first, then disconnect the positive ( + 4
6.
Remove the battery.
3
(cont’d)
Servicing Your Honda
163
08/07/07 14:43:19 32HP4620 0173
Battery
7.
Charge the battery (see following section), unless you have been riding regularly.
8.
Store your battery in an easy-to-reach location off the floor, in an area protected from freezing temperature and direct sunlight.
9.
Clean the compartment after removing the battery for storage. Dry the
10.
compartment and, if paint is missing, re-paint the area.
Slow charge the battery (see following section) once every 30 days.
Installation
1.
2.
battery band.
Make sure the battery band is properly position.
3.
Reinstall in the reverse order of removal.
Be sure to connect the positive ( + ) terminal first, then the negative
( − ) terminal.
4.
Make sure all bolts and other fasteners are secure.
(5)
40 mm
(1.6 in)
(5)battery band
164
Servicing Your Honda
08/07/07 14:43:26 32HP4620 0174
Battery
Battery Charging
Refer to Saf ety Precautions on page 89 .
(1)
(1) ‘‘trickle’’ charger
Be sure to read the information that came with your battery charger and follow the instructions on the battery. Improper charging may damage the battery.
units can be left connected for long periods without risking damage to the battery. However, do not intentionally leave the charger connected longer than the time period recommended in the charger’s instructions.
Avoid using an automotive-type battery charger. An automotive charger can overheat an ATV battery and cause premature damage.
Servicing Your Honda
165
08/07/07 14:43:38 32HP4620 0175
Appearance Care
Frequent cleaning and polishing will keep your Honda looking newer longer.
Frequent cleaning also identifies you as an owner who values his ATV.
A clean ATV is also easier to inspect and service.
General Recommendations
Refer to Saf ety Precautions on page 89 .
To clean your ATV, you may use:
− water
− a mild, neutral detergent and water
− a mild spray and wipe cleaner/polisher
− a mild spray and rinse cleaner/degreaser and water
Avoid products that contain harsh detergents or chemical solvents that could damage the metal, paint, and plastic on your ATV.
If your ATV is still warm from recent operation, give the engine and exhaust system time to cool off.
Park in a shady area. Washing your ATV in bright sunlight may cause the finish to fade because water droplets intensify the sun’s brightness.
Spotting is also more likely because surface water can dry before you have time to wipe it off.
Clean your ATV regularly to protect surface finishes.
We recommend the use of a garden hose to wash your ATV. High pressure washers (like those at coin-operated car washers) can damage certain parts of your ATV.
High pressure water (or air) can damage certain parts of your ATV.
After cleaning, inspect for damage, wear, and leaks (fuel, oil, coolant and brake fluid).
166
Servicing Your Honda
08/07/07 14:43:50 32HP4620 0176
Appearance Care
Washing Your ATV with a Mild Detergent
Refer to Saf ety Precautions on page 89 .
1.
2.
Rinse your ATV thoroughly with cool water to remove loose dirt.
Fill a bucket with cool water. Mix in a mild, neutral detergent, such as dish washing liquid or a product made especially for washing motorcycles or automobiles.
3.
Wash your ATV with a sponge or soft towel. As you wash, check for heavy grime. If necessary, use a mild cleaner/degreaser to remove the grime.
4.
After washing, rinse your ATV thoroughly with plenty of clean water to remove any residue. Detergent residue can corrode alloy parts.
5.
Dry your ATV with a chamois or a soft towel. Leaving water on the surface to air dry can cause dulling and water spots. As you dry, inspect for chips and scratches.
6.
Start the engine and let it idle for several minutes. The engine heat will help dry moist areas.
7.
As a precaution, ride your ATV at a slow speed and apply the brakes several times. This will help dry the brakes and restore normal braking performance.
If the inside of the headlight lens appears clouded immediately after washing, it should clear after a few minutes of riding.
Servicing Your Honda
167
08/07/07 14:44:04 32HP4620 0177
Appearance Care
Spray Cleaning Your ATV
Refer to Saf ety Precautions on page 89 .
Avoid using spray cleaner products on the tyres or suspension components.
Suggestions for using spray cleaner(s) follow:
ATV condition
Dust and fingerprint smudges.
Light road grimes.
Heavy grime. Oil leaks.
Brake dust.
Dull, corroded chrome or aluminum.
Recommended Cleaning
Apply a spray cleaner/polish and wipe paint, chrome, glass, and clear plastic.
Spray any difficult-to-reach or very dirty areas with a spray cleaner/ degreaser.
Rinse and dry.
Apply a spray cleaner/polish and wipe with a non-abrasive cloth.
Use a spray cleaner/degreaser. If necessary, rub with a sponge.
Rinse and dry.
Apply a spray cleaner/polish and wipe with a non-abrasive cloth.
Apply a high quality chrome/ aluminum polish and wipe with a non-abrasive cloth.
168
Servicing Your Honda
08/07/07 14:44:10 32HP4620 0178
Appearance Care
Finishing Touches
Refer to Saf ety Precautions on page 89 .
After washing your ATV, consider using a commercially available spray cleaner/polish or quality liquid or paste wax to finish the job. Use only a non-abrasive polish or wax made specifically for motorcycles or automobiles. Apply the polish or wax according to the instructions on the container.
Servicing Your Honda
169
08/07/07 14:44:13 32HP4620 0179
170
Servicing Your Honda
08/07/07 14:44:21 32HP4620 0180
Tips
Here’s helpful advice on how to prepare for an off-road adventure, how to transport and store your Honda, and how to be an environmentally responsible ATV owner.
Preparing for a Ride ..........................................................................
.
What to Take to the Riding Area ..................................................
.
What to Take on the Trail .............................................................
.
Transporting Your Honda .................................................................
.
Storing Your Honda ..........................................................................
.
Preparation for Storage .................................................................
.
Removal from Storage ..................................................................
.
You & the Environment ....................................................................
.
172
172
173
174
176
177
179
180
Tips
171
08/07/07 14:44:33 32HP4620 0181
Preparing for a Ride
A safe and enjoyable ride begins with good planning and preparation.
Always ride with at least one other person in case you have trouble, and let someone know where you’re going and when you expect to return.
Before riding in an unfamiliar area, find out in advance if you need special permits, get maps so you can study the terrain, and talk to other riders who know the area.
What to Take to the Riding Area
Along with your ATV and riding gear, you should take along some tools and supplies in case you have a problem. For some of the difficulties you might encounter, see Taking Care of the Unexpected, which begins on page 181 .
We recommend that you always take water, food, a first aid kit, and your owner’s manual. Other items you should consider loading on your truck or trailer include: a tool kit tyre repair supplies and tools, and tyres extra parts, control levers, cables, and spark plugs wire, duct tape, and rope extra petrol
For safety, all refueling should be done at a gas station on the way to the riding area or at your base camp.
172
Tips
08/07/07 14:44:38 32HP4620 0182
Preparing for a Ride
What to Take on the Trail
What you take with you during a ride depends on the kind of terrain, how long you expect to ride, how far you might go from your base camp or help, and how experienced you or your companions are in making repairs.
If you decide to take some tools, spare parts, or other supplies on the trail, be sure you can carry them safely and know how to use them. Also, be sure to follow the loading guidelines and weight limit (page 48 ).
Tips
173
08/07/07 14:44:44 32HP4620 0183
Transporting Your Honda
Do not tow your ATV behind a car or other vehicle.
When you transport your ATV, we recommend that you carry the vehicle in its normal operating position (on all four wheels). Do not incline the vehicle upright on its rear end. This can damage the vehicle, and leaking petrol could be a hazard.
Follow these procedures:
1.
Set the parking brake and place the transmission in gear.
2.
Turn the fuel valve OFF.
174
Tips
08/07/07 14:44:54 32HP4620 0184
Transporting Your Honda
3.
Secure the vehicle with tie-down straps in the areas shown.
Suitable tie-down straps are available from your Honda dealer.
Ordinary rope is not recommended because it can stretch under load.
Using tie-down straps in any other areas can damage your ATV.
4.
Rock the vehicle back and forth to make sure the tie-down straps are tight and the vehicle is secure.
(1)
(3)
(1) front cargo rack
(2) rear cargo rack
(2)
(3) trailer hitch
Tips
175
08/07/07 14:44:59 32HP4620 0185
Storing Your Honda
If you won’t be riding for an extended period, such as during the winter, thoroughly inspect your ATV and correct any problem before storing it.
That way, needed repairs won’t be forgotten and it will be easier to get your ATV running again.
We suggest you perform the following procedures to keep your ATV in top condition. These storage procedures will reduce the deterioration that can occur during storage.
176
Tips
08/07/07 14:45:09 32HP4620 0186
Storing Your Honda
Preparation for Storage
Refer to Saf ety Precautions on page 89 .
1.
2.
Change the engine oil and filter (page 110 ).
Make sure the cooling system is filled with a 50/50% antifreeze solution (page 118 ).
3.
Fill the fuel tank. Make sure the fuel fill cap is properly installed.
4.
Check that the fuel valve is OFF.
5.
To prevent rusting in the cylinder, perform the following:
Remove the spark plug cap from the spark plug.
Remove the spark plug.
Do not connect the spark plug to the spark plug cap.
Pour a tablespoon (15 − 20 cm ) of clean engine oil into the cylinder and cover the spark plug hole with a piece of cloth.
With the engine stop switch in the RUN ( ) position, press the start button several times to crank the engine and distribute the oil.
Reinstall the spark plug and spark plug cap.
(cont’d)
Tips
177
08/07/07 14:45:18 32HP4620 0187
Storing Your Honda
6.
Remove the battery and charge it fully. Store it in an area protected from freezing temperatures and direct sunlight. Slow charge the battery (page 165 ) once a month.
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.
Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.
7.
Wash and dry your ATV. Wax all painted surfaces.
8.
9.
Inflate the tyres to their recommended pressures (page 152 ).
Store your ATV in an unheated area, free of dampness, away from sunlight, with a minimum of daily temperature variation.
10.
Place your ATV on blocks to lift all tyres off the floor.
11.
Cover your ATV with a porous material. Avoid using plastic or similar non-breathing, coated materials that restrict air flow and allow heat and moisture to accumulate.
178
Tips
08/07/07 14:45:28 32HP4620 0188
Storing Your Honda
Removal from Storage
Refer to Saf ety Precautions on page 89 .
1.
Uncover and clean your ATV.
2.
If your ATV has been stored for more than four months − change the engine oil (page 110 ).
3.
If your ATV has been stored for more than two months − ask your
Honda dealer to drain and replace the fuel.
4.
5.
Charge the battery (page 165 ) as required. Install the battery.
Perform a pre-ride inspection (page 43 ), then test-ride your ATV at low speeds.
Tips
179
08/07/07 14:45:35 32HP4620 0189
You & the Environment
Owning and riding an ATV can be enjoyable, but you must do your part to protect nature. When you show respect for the land, wildlife, and other people, you also help preserve the sport of off-road riding.
Following are tips on how you can be an environmentally responsible
ATV owner.
Tread Lightly.
Stay on existing roads and trails, avoid surfaces that are easily damaged, and ride only in areas approved for off-road vehicles.
Keep the Noise Down.
Loud vehicles can be offensive. Ride as quietly as possible, don’t remove your spark arrester, and don’t modify the muffler or any other part of your air intake and exhaust systems. Such modifications not only increase noise, they also reduce engine performance and may be illegal.
Choose Sensible Cleaners.
Use a biodegradable detergent when you wash your ATV. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Don’t throw cleaning solvents away; see the following guidelines for proper disposal.
Recycle Wastes.
It’s illegal and thoughtless to put used engine oil in the trash, down a drain, or on the ground. Used oil, petrol, and cleaning solvents contain poisons that can hurt refuse workers and contaminate our drinking water, lakes, rivers, and oceans. Before changing your oil, make sure you have the proper containers. Put oil and other toxic wastes in separate sealed containers and take them to a recycling centre. Call your local office of public works or environmental services to find a recycling centre in your area, and to get instructions on how to dispose of non-recyclable wastes.
180
Tips
08/07/07 14:45:45 32HP4620 0190
Taking Care of the Unexpected
With all the challenges you can encounter off-road, there’s a chance that sometime something may go wrong. This section gives practical advice to help you deal with a wide range of problems. Take time to read this section before you ride. Also review the tips in Preparing f or a Ride
(page 172 ).
General Guidelines ............................................................................
.
If Your Engine Quits or Won’t Start .................................................
.
If You Have a Flat Tyre ....................................................................
.
If the High Coolant Temperature Indicator Lights ............................
.
If a Fuse Blows .................................................................................
.
If You Crash ......................................................................................
.
If You Lose Your Key ......................................................................
.
If the Battery Is Low (or Dead) .........................................................
.
If a Component Fails .........................................................................
.
182
184
187
190
192
196
197
198
199
Taking Care of the Unexpected
181
08/07/07 14:45:54 32HP4620 0191
Taking Care of the Unexpected
General Guidelines
Keeping your ATV well-maintained is the best way to reduce the possibility of having a problem while riding. However, problems can arise even with well-maintained machines.
Remember to take along your owner’s manual, the tool kit that came with your ATV, and any other items (such as tyre repair supplies and additional tools) that might help you solve a problem on your own.
If something goes wrong during a ride, the first thing to do is stop as soon as you safely can. Do not continue riding if you have a flat tyre, or you hear an unusual noise, or your ATV just doesn’t feel right. If you continue riding, you could cause more damage and endanger your own safety.
After stopping, take time to assess the situation. Carefully inspect your
ATV to identify the problem, then consider your options before you decide what to do.
If a problem is relatively minor and you have the tools, supplies, and skills to make a permanent repair, you may be able to fix it on the trail and continue riding. Or, you may be able to make a temporary repair that allows you to slowly ride back to your base where you can make a permanent repair or get help.
When a problem is more serious − or you don’t have the tools, supplies, experience, or time to deal with it − you need to choose the safest way to get yourself and your ATV back to base. For example, if you are close enough, you (or you and another person) might be able to push it back.
182
Taking Care of the Unexpected
08/07/07 14:46:02 32HP4620 0192
Taking Care of the Unexpected
Should you ever have a problem while riding, please follow these guidelines:
Always put personal safety first.
Take time to assess the situation and your options before deciding what to do.
If the problem is relatively minor and you have the tools, supplies, and skills to make a temporary repair, be sure to have permanent repairs made as soon as possible.
Do not continue riding if you are hurt or your ATV is not in safe riding condition.
Additional recommendations for specific problems follow.
Taking Care of the Unexpected
183
08/07/07 14:46:07 32HP4620 0193
If Your Engine Quits or Won’t Start
Proper operation and maintenance can prevent starting and engine performance problems. In many cases, the cause of the problem may be a simple operational oversight.
If you have a problem starting the engine − or experience poor engine performance − the following information may help you. If you can’t correct the problem, see your Honda dealer.
If your ATV won’t start, listen as you press the start button. If you don’t hear the starter motor turning, refer to the Starter motor doesn’t operate symptom. If you can hear the starter motor working normally, refer to the Starter motor works, but the engine won’t start symptom.
184
Taking Care of the Unexpected
08/07/07 14:46:27 32HP4620 0194
If Your Engine Quits or Won’t Start
SYMPTOM: Starter motor doesn’t operate.
POSSIBLE CAUSE ignition switch OFF engine stop switch
OFF
WHAT TO DO
Turn the ignition switch ON.
Slide the engine stop switch to RUN.
transmission not in neutral blown fuse
Shift into neutral.
battery lead loose low (or dead) battery
Replace with a new fuse of the same rating (page 192 ).
Tighten the battery lead.
Charge the battery (page 165 ).
If charging doesn’t help, see your faulty starter motor
Honda dealer.
If all possible causes are negative, the starter motor may be faulty. See your Honda dealer.
SYMPTOM: Starter motor works, but the engine won’t start.
POSSIBLE CAUSE WHAT TO DO out of fuel flooded engine loose or unconnected spark plug cap loose battery cables weak battery
Fill the fuel tank.
See F looded Engine (page 62 ).
Install the spark plug cap securely. If the engine still won’t start, see your
Honda dealer.
Tighten the battery terminal bolts.
Charge the battery (page 165 ). If charging doesn’t help, see your
Honda dealer.
Taking Care of the Unexpected
185
08/07/07 14:46:41 32HP4620 0195
If Your Engine Quits or Won’t Start
SYMPTOM: Engine starts, but runs poorly.
POSSIBLE CAUSE high coolant
WHAT TO DO temperature runs erratically,
Check the high coolant temperature indicator. Refer to If the High
Coolant T emper atur e Indicator
Lights, page 190 .
See your Honda dealer.
misfires blubbers (rich fuel mixture) sooty exhaust (rich fuel mixture) detonates or pings under load
See your Honda dealer.
See your Honda dealer.
If applicable, switch to the recommended octane petrol
(page 102 ) or change your brand of afterfires (backfires) pre-ignition (runs on after ignition switched OFF) petrol. If the problem persists, see your Honda dealer.
See your Honda dealer.
See your Honda dealer.
186
Taking Care of the Unexpected
08/07/07 14:46:49 32HP4620 0196
If You Have a Flat Tyre
How you handle a flat tyre on the trail depends on how serious the tyre damage is, and what tools and supplies you have with you.
If you have a slow leak or a minor puncture, use the plug method to make a temporary repair. (The plug method is applied from the outside of the tyre and is the same as that for conventional tubeless tyres.)
A plug-type repair kit, available at most auto parts stores or service stations, provides a plug, an installation tool, tyre cement, and an instruction sheet. Follow the instructions provided with the repair kit to make a temporary repair.
As soon as possible, have the tyre permanently repaired by your Honda dealer. Any tyre that cannot be repaired should be replaced.
Whenever the ATV is to be operated far from service facilities or available transportation, we recommend that you carry a tyre pump and a repair kit with the vehicle.
If the leak is more serious, or a temporary repair doesn’t hold, the tyre must be replaced. The tyre will also need to be replaced if it is damaged
(page 156 ). Replacing a tyre involves removing and re-installing the wheel (page 188 ).
If you are unable to repair a flat tyre on the trail, you will need to send for help. We strongly recommend that you do not try to ride with a flat tyre. The ATV will be hard to handle, and if the tyre comes off the rim, it may lock up the wheel and cause you to crash.
Taking Care of the Unexpected
187
08/07/07 14:47:01 32HP4620 0197
If You Have a Flat Tyre
Emergency Wheel Removal/Installation
Refer to Saf ety Precautions on page 89 .
(1)
(1) wheel nuts
(1) (2)
(2) wheel rim
Removal
1.
Park your ATV on a firm, level surface.
2.
Loosen − but do not remove − 1
3.
Raise the front (or rear) wheels off the ground and place a support block under the vehicle.
4.
Remove the wheel nuts.
5.
Remove the wheel.
Avoid getting grease, oil, or dirt on the front brake disc or pad surfaces when removing and installing each wheel. Any contamination can cause poor brake performance or rapid pad wear after reassembly.
188
Taking Care of the Unexpected
08/07/07 14:47:09 32HP4620 0198
If You Have a Flat Tyre
Installation
1.
Position the wheel.
2.
Position the wheel nuts so that the tapered sides face the wheel
3.
Hand-tighten the wheel nuts on the wheel, then lower the ATV to the ground before tightening the nuts in a crisscross (rather than circular) pattern to the specified torque:
64 N·m (6.5 kgf·m , 47 lbf·ft)
If a torque wrench was not used for installation, see your Honda dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capability.
Taking Care of the Unexpected
189
08/07/07 14:47:17 32HP4620 0199
If the High Coolant Temperature
Indicator Lights
Normally, the high coolant temperature indicator will only light momentarily when you turn the ignition ON ( ). Occasionally, it may flicker at or near idling speed.
High coolant temperature may be caused by restriction of air flow to the radiator (such as mud caked on the radiator), extended idling, an oil leak, a coolant leak, a low oil level, a low coolant level, or extended operation under adverse conditions.
If the indicator comes on while you’re riding, don’t ignore it. Pull safely to a stop. Stop the engine as soon as it’s safe to do so, and let it cool.
Continuing to ride with high coolant temperature or an overheated engine can cause serious engine damage.
A steaming engine indicates a coolant leak. Shut the engine off and wait until the steaming stops. Look for a leak, but don’t touch the engine or radiator system. Let everything cool off first.
Check for any restriction of air flow to the radiator.
If there’s no obvious problem, leave the engine on so the fan and coolant circulating system can continue working. Monitor the high coolant temperature indicator. The indicator may turn off after a brief stop with no load on the engine.
Check the radiator fan.
If the fan is not working, turn the engine off. Open the fuse box
(page 193 ) and check the radiator fan fuse. If the fuse is blown, replace it with the proper (same rating) spare fuse. Start the engine. If the high coolant temperature indicator comes on and stays on, turn the engine off.
If the radiator fan is working, visually check the coolant level in the reserve tank, located under the rear fender. It isn’t necessary to touch the radiator system.
190
Taking Care of the Unexpected
08/07/07 14:47:26 32HP4620 0200
If the High Coolant Temperature
Indicator Lights
If the reserve tank is low or empty, don’t ride without adding coolant
(page 119 ). After adding coolant, turn the engine on and check the high coolant temperature indicator.
If the indicator doesn’t turn off, do not ride. The engine needs repair.
Transport your ATV to a Honda dealer (page 174 ).
If the temperature drops to normal, check the coolant level. If it has gone down, add more coolant.
Check for an oil leak.
Check the oil level. If necessary, add the recommended oil (page 108 ) to the upper level mark. If you must leave your ATV to get oil, secure it as much as possible.
Start the engine, and check that the high coolant temperature indicator goes off.
If you are able to resume riding, continue to monitor the high coolant temperature indicator frequently.
If there is an oil leak − do not ride the ATV until the leak is repaired by
Honda dealer (page 174 ).
If there’s a mild coolant leak, you can ride for awhile, carefully watching the indicator. Be prepared to stop and add more coolant or water. If the leak is bad, transport your ATV to a Honda dealer
(page 174 ).
Taking Care of the Unexpected
191
08/07/07 14:47:36 32HP4620 0201
If a Fuse Blows
All of the electrical circuits on your ATV have fuses to protect them from damage caused by excess current flow (short circuit or overload).
If something electrical on your ATV stops working, the first thing you
Check all the fuses before looking elsewhere for another possible cause of the problem. Replace any blown fuses and check component operation.
(1)
(1) blown fuse
The main fuse and the circuit fuses are located in the battery compartment.
Recommended Fuses main fuse other fuse
30 A
15 A, 10 A × 3
192
Taking Care of the Unexpected
08/07/07 14:47:45 32HP4620 0202
If a Fuse Blows
Main Fuse Access
1.
To prevent an accidental short circuit, turn the ignition switch OFF
( ) before checking or replacing the fuses.
2.
Remove the seat (page 100 ).
3.
Remove the rear fender cover (page 120 ).
4.
UNDER REAR FENDER COVER
(3)
(2) (4)
(2) main fuse
(3) fuse box cover
5.
Pull the main fuse out.
(4) spare main fuse
(cont’d)
Taking Care of the Unexpected
193
08/07/07 14:47:55 32HP4620 0203
If a Fuse Blows
Circuit Fuse Access
(6)
(5) circuit fuses
6.
retaining clips.
(5)
(6) spare fuses
If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating.
Replacing a f use with one that has a higher rating greatly increases the chance of damage to the electrical system.
7.
Install the fuse box cover.
8.
9.
Install the rear fender cover.
Install the seat.
194
Taking Care of the Unexpected
08/07/07 14:48:00 32HP4620 0204
If a Fuse Blows
If you do not have a spare fuse and you cannot ride the ATV without fixing the problem, take a fuse of the same rating or a lower rating from one of the other circuits that you can do without temporarily.
If you replace a blown fuse with a spare fuse that has a lower rating, replace the fuse with the correct rating as soon as you can. Also remember to replace any spare fuses that were installed.
If the replacement fuse of the same rating burns out in a short time, there is probably a serious electrical problem on your ATV. Leave the blown fuse in that circuit and have your ATV checked by your Honda dealer.
Taking Care of the Unexpected
195
08/07/07 14:48:06 32HP4620 0205
If You Crash
Personal safety is your first priority after a crash. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. If you cannot ride safely, send someone for help. Do not ride if you will risk further injury.
If you decide you are capable of riding safely, carefully inspect your
ATV for damage and determine if it is safe to ride. Check the tightness of critical nuts and bolts securing such parts as the handlebar, control levers, brakes, and wheels.
If there is minor damage, or you are unsure about possible damage but decide to try riding the ATV back to your base, ride slowly and cautiously.
Sometimes, crash damage is hidden or not immediately apparent. When you get home, thoroughly check your ATV and correct any problems you find. Also, be sure to have your Honda dealer check the frame and suspension after any serious crash.
196
Taking Care of the Unexpected
08/07/07 14:48:13 32HP4620 0206
If You Lose Your Key this number to have a duplicate key made.
If you lose your key and aren’t carrying a duplicate, either get your spare or have one made. If you don’t know your key number, call the dealer where you purchased your Honda ATV. They may have it listed in their records. If they don’t, transport your ATV to them or the nearest
Honda dealer. The dealer will probably have to remove the ignition switch assembly to find the key number so they can make a key for you.
KEY NO.
(1)
(1) key number
Taking Care of the Unexpected
197
08/07/07 14:48:20 32HP4620 0207
If the Battery Is Low (or Dead)
Your ATV will operate even if the battery is low (or dead), as long as the engine is running. If the engine is not running, it may be started using the recoil starter.
1.
Shift the shift lever in neutral position.
2.
3.
Apply the parking brake.
Turn the ignition switch to the ‘‘ON’’ ( ) position.
4.
Use the recoil starter (page 64 ) to start the engine.
Jump starting is not recommended, especially if you use an automobile battery. The greater amperage of an automobile battery when the car engine is running can damage your ATV’s electrical system.
Bump starting is also not recommended.
If you can’t charge the battery or it appears unable to hold a charge, contact your Honda dealer.
198
Taking Care of the Unexpected
08/07/07 14:48:26 32HP4620 0208
If a Component Fails
The brake levers or pedal, control cables, and other components can be damaged as you ride in dense brush or over rocky terrain. Making a trailside repair depends on how serious the damage is and what tools and supplies you have with you.
If any component of the brake system is damaged, you may be able to ride carefully back to your base using the other brake components for slowing or stopping.
If you damage a throttle cable or other critical component, your ATV may be unsafe to ride. Carefully assess the damage and make any repairs that you can. But if there is any doubt, it’s best to be conservative and safe.
Taking Care of the Unexpected
199
08/07/07 14:48:28 32HP4620 0209
200
Taking Care of the Unexpected
08/07/07 14:48:34 32HP4620 0210
Technical Information
This section contains dimensions, capacities, and other technical data, plus information on government requirements and how to break-in your
ATV.
Vehicle Identification ........................................................................
.
Specifications ....................................................................................
.
Break-in Guidelines ..........................................................................
.
Petrol Containing Alcohol .................................................................
.
202
204
208
209
Technical Information
201
08/07/07 14:48:43 32HP4620 0211
Vehicle Identification
Serial Numbers
The VIN, engine serial number, and key number may be required when ordering replacement parts. Record the numbers here for your reference.
VIN
FRONT
(1) crankcase.
ENGINE No.
LEFT SIDE
(1) VIN
(2)
(2) engine number
202
Technical Information
08/07/07 14:48:51 32HP4620 0212
Vehicle Identification
Colour Label & Code
seat (page 100 ) to check the label.
The colour code is helpful when ordering replacement parts. Record the colour and code here for your reference.
COLOUR
CODE
UNDER SEAT
(1)
(1) colour label
Technical Information
203
08/07/07 14:49:10 32HP4620 0213
Specifications
Dimensions overall length overall width overall height wheelbase ground clearance
Fuel & Lubricants fuel recommendation fuel tank capacity fuel tank reserve engine oil capacity engine oil recommendation cooling system recommendation cooling system capacity
2,055 mm (80.9 in)
1,172 mm (46.1 in)
1,148 mm (45.2 in)
1,146 mm (45.1 in)
1,256 mm (49.4 in)
1,249 mm (49.2 in)
165 mm (6.5 in)
…TRX420TM
…TRX420FM
…TRX420TM
…TRX420FM unleaded petrol, research octane number of 91 or higher
13.3
(3.51 US gal , 2.93 Imp gal) including reserve
2.6
(0.69 US gal , 0.57 Imp gal) after disassembly:
3.1
(3.3 US qt , 2.7 Imp qt) after draining:
2.7
(2.9 US qt , 2.4 Imp qt) after draining & oil filter change:
2.8
(3.0 US qt , 2.5 Imp qt)
API Service Classification SE, SF or
SG
Honda 4-stroke oil or an equivalent
High quality ethylene glycol antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines
1.5
(1.6 US qt , 1.3 Imp qt)
204
Technical Information
08/07/07 14:49:23 32HP4620 0214
Specifications
Capacities passenger capacity maximum weight capacity operator only
220 kg (485 lbs) rider, all cargo and accessories
Engine Specifications displacement bore & stroke compression ratio spark plug
(standard) valve clearance
(cold) spark plug gap idle speed
420.2 cm (25.63 cu-in)
86.5
× 71.5 mm (3.41
× 2.81 in)
9.9 : 1
BKR5E-11 (NGK) or K16PR-U11 (DENSO) intake: 0.15 mm (0.006 in) exhaust: 0.23 mm (0.009 in)
1.00
− 1.10 mm (0.039
− 0.043 in)
1,400 ± 100 min (rpm)
(NO ADJUSTMENT)
Technical Information
205
08/07/07 14:49:46 32HP4620 0215
Specifications
Power Transmission primary reduction secondary reduction final reduction transmission ratio front (TRX420FM only) rear
1st
2nd
3rd
4th
5th reverse final drive
Noise level (ISO 5131)
Vibration on seat
(EN 1032, ISO 5008)
Vibration on handlegrip
(ISO 5349:2001, EN
709)
77.0 dB(A)
Not exceed 0.5 m/s
6.0 m/s 2
2
Chassis & Suspension caster trail tyre size, front tyre size, rear tyre pressure, front & rear (cold)
6.34° …TRX420TM
3° …TRX420FM
25.1 mm (0.99 in) …TRX420TM
9.0 mm (0.35 in) …TRX420FM
AT24 × 8-12 ★★
AT24 × 10-11 ★★
25.0 kPa (3.6 psi)
MAXXIS M977
MAXXIS M978
2.103
1.818
3.231
3.154
3.857
2.235
1.571
1.178
0.848
4.831
shaft
206
Technical Information
08/07/07 14:50:07 32HP4620 0216
Specifications
Electrical battery generator
Lights headlight brake/tail light neutral indicator reverse indicator high coolant temperature indicator
PGM-FI indicator
4WD indicator
(TRX420FM only)
12 V − 12 Ah
0.359 kW/5,000 min (rpm)
12 V 30/30 W
LED
LED
LED
LED
LED
LED
× 2
Fuses main other
30 A
15 A, 10 A × 3
Torque Specification engine oil drain bolt engine oil filter cover bolt rear final gear case oil drain bolt differential oil drain plug (TRX420FM only) wheel nuts
25 N·m (2.5 kgf·m , 18 lbf·ft)
10 N·m (1.0 kgf·m , 7 lbf·ft)
12 N·m (1.2 kgf·m , 9 lbf·ft)
12 N·m (1.2 kgf·m , 9 lbf·ft)
64 N·m (6.5 kgf·m , 47 lbf·ft)
Technical Information
207
08/07/07 14:50:12 32HP4620 0217
Break-in Guidelines
Help assure your ATV’s future reliability and performance by paying extra attention to how you ride during the first operating day or 25 km
(15 miles).
During this period, avoid full-throttle starts, rapid acceleration, and constant rpm operation.
208
Technical Information
08/07/07 14:50:18 32HP4620 0218
Petrol Containing Alcohol
If you decide to use a petrol containing alcohol (gasohol), be sure its octane rating is at least as high as that recommended above.
There are two types of gasohol: One contains ethanol, and the other contains methanol. Do not use gasohol that contains more than 10% ethanol. Do not use gasohol that contains methanol (methyl or wood alcohol) unless it also contains cosolvents and corrosion inhibitors for methanol. Never use petrol containing more than 5% methanol, even if it has cosolvents and corrosion inhibitors.
Engine performance problems resulting from the use of fuels that contain alcohol are not covered under the warranty. Honda cannot endorse the use of fuels containing methanol since evidence of their suitability is not yet complete.
Before buying fuel from an unfamiliar station, try to find out if the fuel contains alcohol. If it does, confirm the type and percentage of alcohol used. If you notice any undesirable operating symptoms while using a petrol that contains alcohol, or one that you think contains alcohol, switch to a petrol that you know does not contain alcohol.
Technical Information
209
08/07/07 14:50:30 32HP4620 0219
Table of Contents
The following presents the contents of each section of your owner’s manual.
ATV SAFETY .....................................................................................
.
Important Safety Information ...............................................................
.
Safety Labels .........................................................................................
.
1
2
5
INSTRUMENTS & CONTROLS ......................................................
. 9
Operation Component Locations ..........................................................
.
11
Indicators & Displays ............................................................................
.
14
Multi-function Display ......................................................................
.
18
Gear Position Indicator ......................................................................
.
19
Oil Change Indicator .........................................................................
.
20
Odometer ...........................................................................................
.
21
Tripmeter ...........................................................................................
.
21
Hourmeter .........................................................................................
.
22
Fuel Gauge ........................................................................................
.
23
210
Table of Contents
08/07/07 14:50:55 32HP4620 0220
Table of Contents
Controls & Features ..............................................................................
.
24
Fuel Valve .........................................................................................
.
24
Ignition Switch ..................................................................................
.
25
2WD/4WD Select Lever ( TRX420FM only) ....................................
.
26
Start Button .......................................................................................
.
27
Engine Stop Switch ...........................................................................
.
27
Headlight Switch ...............................................................................
.
28
Headlight Dimmer Switch .................................................................
.
28
Horn Button .......................................................................................
.
28
Recoil Starter .....................................................................................
.
29
Throttle Lever ...................................................................................
.
30
Reverse Selector Knob ......................................................................
.
31
Front Brake Lever .............................................................................
.
32
Rear Brake Lever/Parking Brake Lever ............................................
.
32
Rear Brake Pedal ...............................................................................
.
32
Parking Brake ....................................................................................
.
33
Flag Pole Bracket ..............................................................................
.
34
Trailer Hitch ......................................................................................
.
35
BEFORE RIDING ..............................................................................
.37
Are You Ready to Ride?
.......................................................................
.
38
Protective Apparel .............................................................................
.
38
Rider Training ...................................................................................
.
40
Age Recommendation .......................................................................
.
41
No Passengers ...................................................................................
.
41
No Alcohol or Drugs .........................................................................
.
42
Is Your ATV Ready to Ride?
................................................................
.
43
Pre-ride Inspection ............................................................................
.
43
Load Limits & Guidelines .....................................................................
.
47
Loading .............................................................................................
.
47
Load Limits .......................................................................................
.
48
Loading Guidelines ...........................................................................
.
49
(cont’d)
Table of Contents
211
08/07/07 14:51:20 32HP4620 0221
Table of Contents
BEFORE RIDING (cont’d)
Accessories & Modifications ................................................................
.
50
Accessories ........................................................................................
.
50
Modifications ....................................................................................
.
51
BASIC OPERATION & RIDING .....................................................
.53
Safe Riding Precautions ........................................................................
.
55
Off-road Use Only ............................................................................
.
55
Keep Hands and Feet on Controls .....................................................
.
56
Control Speed ....................................................................................
.
57
Use Care on Unfamiliar or Rough Terrain ........................................
.
58
Do Not Perform Stunts ......................................................................
.
59
Starting & Stopping the Engine ............................................................
.
60
Preparation ........................................................................................
.
60
Starting Procedure .............................................................................
.
61
Flooded Engine .................................................................................
.
62
Bank Angle Sensor Ignition Cut-off System ....................................
.
62
Stalled Engine ...................................................................................
.
63
How to Stop the Engine ....................................................................
.
63
Using the Recoil Starter ....................................................................
.
64
Shifting Gears .......................................................................................
.
65
Riding in Reverse ..................................................................................
.
67
Braking ..................................................................................................
.
69
Riding Your ATV .................................................................................
.
71
Making Turns ....................................................................................
.
71
Skidding or Sliding ...........................................................................
.
73
Riding Up Hills .................................................................................
.
74
Riding Down Hills ............................................................................
.
78
Crossing or Turning on Hills or Slopes .............................................
.
79
Riding Over Obstacles ......................................................................
.
81
Riding Through Water ......................................................................
.
82
Parking ..................................................................................................
.
83
212
Table of Contents
08/07/07 14:51:41 32HP4620 0222
Table of Contents
SERVICING YOUR HONDA ............................................................
.85
Bef ore You Service Your Honda
The Importance of Maintenance ...........................................................
.
87
Maintenance Safety ...............................................................................
.
88
Important Safety Precautions ............................................................
.
89
Maintenance Schedule ..........................................................................
.
90
Maintenance Record ..............................................................................
.
94
Service Preparations
Maintenance Component Locations ......................................................
.
95
Tool Kit .................................................................................................
.
98
Owner’s Manual Storage .......................................................................
.
99
Seat Removal
Clip Removal
....................................................................................
....................................................................................
.
.
100
101
Service Procedures
Fluids & Filters
Fuel ...................................................................................................
.
Engine Oil & Filter ............................................................................
.
Gear Case Oil ....................................................................................
.
Differential Oil ( TRX420FM only) ...................................................
.
Coolant ..............................................................................................
.
Air Cleaner ........................................................................................
.
102
105
114
116
118
124
Engine
Throttle ..............................................................................................
.
Clutch System ...................................................................................
.
Reverse Lock System ........................................................................
.
Spark Plug .........................................................................................
.
Valves ................................................................................................
.
Spark Arrester ...................................................................................
.
130
132
133
134
137
138
(cont’d)
Table of Contents
213
08/07/07 14:52:01 32HP4620 0223
Table of Contents
Chassis
Brakes ................................................................................................
.
Tyres .................................................................................................
.
Guards ...............................................................................................
.
Drivetrain Boots ................................................................................
.
139
150
157
159
Electrical
Battery ...............................................................................................
.
161
Appearance Care ...............................................................................
.
166
TIPS ..................................................................................................
.
Preparing for a Ride ..........................................................................
.
What to Take to the Riding Area ..................................................
.
What to Take on the Trail .............................................................
.
Transporting Your Honda .................................................................
.
Storing Your Honda ..........................................................................
.
Preparation for Storage .................................................................
.
Removal from Storage ..................................................................
.
You & the Environment ....................................................................
.
171
172
172
173
174
176
177
179
180
TAKING CARE OF THE UNEXPECTED ..................................
.
General Guidelines ............................................................................
.
If Your Engine Quits or Won’t Start .................................................
.
If You Have a Flat Tyre ....................................................................
.
If the High Coolant Temperature Indicator Lights ............................
.
If a Fuse Blows .................................................................................
.
If You Crash ......................................................................................
.
If You Lose Your Key ......................................................................
.
If the Battery Is Low (or Dead) .........................................................
.
If a Component Fails .........................................................................
.
181
182
184
187
190
192
196
197
198
199
214
Table of Contents
08/07/07 14:52:11 32HP4620 0224
Table of Contents
TECHNICAL INFORMATION ....................................................
.
Vehicle Identification ........................................................................
.
Specifications ....................................................................................
.
Break-in Guidelines ..........................................................................
.
Petrol Containing Alcohol .................................................................
.
201
202
204
208
209
TABLE OF CONTENTS ................................................................
.
210
INDEX ..............................................................................................
.
226
MANUFACTURER AND AUTHORISED
REPRESENTATIVE FOR EU MARKET ...................................
.
228
Table of Contents
215
08/07/07 14:52:16 32HP4620 0225
Index
A accessories ............................................................................................
. 50 age recommendation ............................................................................
. 41 air cleaner, dust cover .......................................................................................
. 128 filter ................................................................................................
. 124 housing drain tube ..........................................................................
. 129 air pressure, gauge ................................................................................................
. 99 tyre .................................................................................................
. 151 apparel, protective ................................................................................
. 38 appearance care ..................................................................................
. 166
B bank angle sensor ignition cut-off system ............................................
. 62 battery .................................................................................................
. 161 brakelight switch adjustment ..............................................................
. 148 brakes, cables ..............................................................................................
. 147 draining water from ........................................................................
. 149 fluid ................................................................................................
. 139 front brake lever ...............................................................................
. 32 pad wear .........................................................................................
. 142 parking .............................................................................................
. 33 rear brake lever .................................................................................
. 32 rear brake lever freeplay ................................................................
. 145 rear brake pedal ................................................................................
. 32 rear brake pedal freeplay ................................................................
. 143 shoe wear ........................................................................................
. 147 braking .................................................................................................
. 69
216
Index
08/07/07 14:52:22 32HP4620 0226
Index break-in guidelines .............................................................................
. 208 button, horn ..................................................................................................
. 28 hourmeter/odometer/tripmeter select .......................
. 14, 17, 20, 21, 22
C capacity, fuel ......................................................................................
. 103 care, appearance .................................................................................
. 166 cargo, loading and operational guidelines ...................................................
. 49 weight limit ......................................................................................
. 48 cleaning, appearance care ...................................................................
. 166 climbing hills ........................................................................................
. 74 clips ....................................................................................................
. 101 clutch system ......................................................................................
. 132 colour label .........................................................................................
. 203 compartment, owner’s manual ................................................................................
. 99 tool kit ..............................................................................................
. 98 component fails ..................................................................................
. 199 controls & features ...............................................................................
. 24 crash, if you ........................................................................................
. 196 crossing or turning on hills or slopes ....................................................
. 79
Index
217
08/07/07 14:52:27 32HP4620 0227
Index
D differential oil (TRX420FM only) .....................................................
. 116 dimmer switch, headlight .....................................................................
. 28 dipstick ...............................................................................................
. 109 display check ........................................................................................
. 15 display, multi-function .........................................................................
. 18 driveshaft boots (TRX420FM only) ..................................................
. 160 drivetrain boots ...................................................................................
. 162
E engine, flooded .............................................................................................
. 62 guard ..............................................................................................
. 157 number ...........................................................................................
. 202 oil ...................................................................................................
. 105 pinging ...........................................................................................
. 102 starting ..............................................................................................
. 60 stop switch ........................................................................................
. 27 stopping ............................................................................................
. 63 won’t start ......................................................................................
. 184 environment .......................................................................................
. 180 exhaust system, cleaning ............................................................................................
. 44 purge ..............................................................................................
. 138
218
Index
08/07/07 14:52:32 32HP4620 0228
Index
F final gear case oil ...............................................................................
. 114 flag pole bracket ...................................................................................
. 34 flat tyre ...............................................................................................
. 187 flooded engine ......................................................................................
. 62 fuel, fill cap gauge
...........................................................................................
. 103
...............................................................................................
. 23 recommendation .............................................................................
. 102 refueling .........................................................................................
. 103 reserve fuel supply .........................................................................
. 103 tank capacity ..................................................................................
. 103 valve .................................................................................................
. 24 fuses ...................................................................................................
. 192
G gap, spark plug ...................................................................................
. 135 gasohol ...............................................................................................
. 209 gear case oil ........................................................................................
. 114 gear shifting .........................................................................................
. 65 guards .................................................................................................
. 158
Index
219
08/07/07 14:52:38 32HP4620 0229
Index
H headlight dimmer switch ......................................................................
. 28 headlight switch ...................................................................................
. 28 hills, crossing or turning on slopes ............................................................
. 79 riding down hills ..............................................................................
. 78 riding up hills ...................................................................................
. 74 stopping on hills ...............................................................................
. 76 horn button ...........................................................................................
. 28 hourmeter .................................................................................
. 17, 18, 22 hourmeter/odometer/tripmeter select button ................
. 14, 17, 20, 21, 22
I identification, vehicle .........................................................................
. 202 ignition switch ......................................................................................
. 25 indicators, gear position indicator ..........................................................
. 17, 18, 19 high coolant temperature indicator .....................................
. 14, 16, 190 neutral indicator .........................................................................
. 14, 16 oil change indicator ..............................................................
. 17, 18, 20
PGM-FI indicator .......................................................................
. 14, 16 reverse indicator .........................................................................
. 14, 16
4WD indicator (TRX420FM only) ......................................
. 14, 16, 26 inspection, pre-ride ...............................................................................
. 43
220
Index
08/07/07 14:52:45 32HP4620 0230
Index
K key, lost .................................................................................................
. 197 number ..........................................................................................
. 197 kit, tool .................................................................................................
. 98
L labels, safety ...........................................................................................
. 5 lamp check ...........................................................................................
. 14 lever, 2WD/4WD select (TRX420FM only) ........................................
. 26 limit, weight .........................................................................................
. 48 load limits .............................................................................................
. 48 loading guidelines ................................................................................
. 49 lubrication, differential oil (TRX420FM only) .................................................
. 116 engine oil ........................................................................................
. 105 gear case oil ....................................................................................
. 114
M maintenance, component locations .........................................................................
. 95 importance ........................................................................................
. 87 precautions .......................................................................................
. 89 record ...............................................................................................
. 94 safety ................................................................................................
. 88 schedule ............................................................................................
. 90
(cont’d)
Index
221
08/07/07 14:52:50 32HP4620 0231
Index maximum weight limit .........................................................................
. 48 modifications ........................................................................................
. 51 multi-function display ..........................................................................
. 18
N neutral indicator .............................................................................
. 14, 16 numbers, serial ...................................................................................
. 202
O obstacles, riding over ...........................................................................
. 81 odometer ...................................................................................
. 17, 18, 21 oil, differential (TRX420FM only) ......................................................
. 116 engine .............................................................................................
. 105 gear case .........................................................................................
. 114 operation component locations .............................................................
. 11 owner’s manual storage ........................................................................
. 99
222
Index
08/07/07 14:52:55 32HP4620 0232
Index
P parking .................................................................................................
. 83 passenger, no carrying ..........................................................................
. 41 pavement, no riding on .........................................................................
. 55 petrol ..................................................................................................
. 102 petrol containing alcohol ....................................................................
. 209 pinging, engine ...................................................................................
. 102 plug, spark ..........................................................................................
. 134 pre-ride inspection ................................................................................
. 43 problems, unexpected .........................................................................
. 181 propeller shaft boots & yoke joint boot ..............................................
. 159 protective apparel .................................................................................
. 38
Index
223
08/07/07 14:53:00 32HP4620 0233
Index
R rear final gear case oil ........................................................................
. 114 recoil starter ..........................................................................................
. 29 removal, seat ......................................................................................
. 100 reverse, assist cable ......................................................................................
. 133 assist lever ......................................................................................
. 133 gear, shifting into .............................................................................
. 67 indicator .....................................................................................
. 14, 16 riding in ............................................................................................
. 67 selector knob ....................................................................................
. 31 rider training .........................................................................................
. 40 riding, basic operations ................................................................................
. 53 clothing .............................................................................................
. 38 over obstacles ...................................................................................
. 81 precautions .......................................................................................
. 55 preparing for ..................................................................................
. 172 safety ..................................................................................................
. 2 safety precautions .............................................................................
. 55 through water ...................................................................................
. 82
224
Index
08/07/07 14:53:05 32HP4620 0234
Index
S safety, important precautions .......................................................................
. 89 labels ..................................................................................................
. 5 riding precautions .............................................................................
. 55 schedule, maintenance ..........................................................................
. 90 seat removal .......................................................................................
. 100 select lever, 2WD/4WD .......................................................................
. 26 serial numbers ....................................................................................
. 202 shifting gears ........................................................................................
. 65 skid plate ............................................................................................
. 157 skidding or sliding ................................................................................
. 73 spark arrester ......................................................................................
. 138 spark knock ........................................................................................
. 102 spark plug ...........................................................................................
. 134 specifications ......................................................................................
. 204 speedometer ...................................................................................
. 17, 18 stalling on a hill ....................................................................................
. 76 start button ............................................................................................
. 27
(cont’d)
Index
225
08/07/07 14:53:09 32HP4620 0235
Index starting, engine ...............................................................................................
. 60 troubleshooting ...............................................................................
. 184 stop switch, engine ...............................................................................
. 27 stopping engine ....................................................................................
. 63 storage,
ATV ...............................................................................................
. 176 owner’s manual ................................................................................
. 99 switch, engine stop .......................................................................................
. 27 headlight ...........................................................................................
. 28 headlight dimmer .............................................................................
. 28 ignition .............................................................................................
. 25
226
Index
08/07/07 14:53:14 32HP4620 0236
Index
T throttle, cable ...............................................................................................
. 131 lever ..................................................................................
. 30, 130, 131 tyres, air pressure .....................................................................................
. 151 flat ..................................................................................................
. 187 repairing .........................................................................................
. 155 replacing .........................................................................................
. 156 tread conditions ......................................................................
. 153, 154 tool kit ..................................................................................................
. 98 trailer hitch ...........................................................................................
. 35 trailer towing, operational guidelines ......................................................................
. 49 weight limits .....................................................................................
. 48 training, rider ........................................................................................
. 40 transporting your ATV .......................................................................
. 174 tripmeter ...................................................................................
. 17, 18, 21 trouble, unexpected ............................................................................
. 181 troubleshooting, starting .....................................................................
. 184 turning, on hills or slopes ...............................................................................
. 79 on level ground .................................................................................
. 71
Index
227
08/07/07 14:53:19 32HP4620 0237
Index
V valve, fuel .............................................................................................
. 24 valve clearance ...................................................................................
. 137 vehicle identification no. (VIN) .........................................................
. 202
W warning labels ........................................................................................
. 5 washing your ATV .............................................................................
. 168 water, draining from brakes ......................................................................
. 149 riding through ...................................................................................
. 82 weight limit ..........................................................................................
. 48 wheel removal ....................................................................................
. 188
228
Index
08/07/07 14:53:25 32HP4620 0238
Manufacturer and Authorised
Representative for EU Market
Manufacturer
Honda of South Carolina
Mfg., Inc.
1111 Honda way
Timmonsville,
South Carolina 29161,
U.S.A.
Authorised Representative for EU Market
Honda Motor Europe Ltd.
Aalst Office
Wijngaardveld 1
(Noord V), B-9300 Aalst
Belgium
Manufacturer and Authorised Representative for EU Market
229
08/07/07 14:53:28 32HP4620 0239
advertisement