Sylvania DVR91DG Owner's Manual

Before you start
Owner’s Manual
DVD Recorder
OPEN/CLOSE
CHANNEL
REC SPEED
REV
FWD
STOP
PLAY
POWER
REC/OTR
S-VIDEO
VIDEO
L AUDIO R
Please read before using this equipment.
If you need additional operating assistance after reading this owner’s manual or to
order replacement accessories, please call
Connection to a TV
(Before you use this unit, you need to complete connections.)
(Back of This Unit)
COMPONENT
VIDEO OUTPUT
VIDEO IN
IN
S-VIDEO
IN
OUT
VIDEO OUT
Y
L
OUT
L
PB/CB
R
ANTENNA
R
PR/CR
AUDIO IN
(L1)
1
RF cable
(supplied)
AC 120V ANT IN
AUDIO OUT
5
(Back of TV)
Set channel 3 or 4.
CHANNEL
3
4
Note
AUDIO IN VIDEO IN
R
L
Antenna in jack
RF cable
3 (commercially
available)
• The quality of
picture may
become poor if this
unit is connected to
an RF modulator.
To record a program easily, refer to “Easy DVD recording” on pages 16-17 after connections are completed.
(You CANNOT record on any copyright protected DVD disc with this unit.)
DVR91DG_E7A01UD.indd 1
Español
STEREO AUDIO/VIDEO
RF Modulator
(commercially available)
TO TV
6
Turn on your TV
and select channel
3 or 4.
Others
2
4
Audio/Video cables
(supplied)
Changing the
Setup menu
Cable Antenna
TV signal
or
Editing
If your TV has AUDIO/VIDEO input jacks, see the section “Connections” on pages 13–15. If not, it is still possible to connect
this unit to your TV by using a Stereo Audio/Video RF modulator. In this case, follow the instructions below.
1) The antenna input jack of your TV may have been already occupied. If so, disconnect the RF cable from your TV, and then
connect the RF cable to the ANTENNA IN jack of this unit.
2) Connect the ANTENNA OUT jack of this unit to your RF modulator (usually marked “ANT IN”) by the RF cable.
3) Connect your RF modulator to your TV by another RF cable.
4) Connect the AUDIO/VIDEO output jacks of this unit to the AUDIO/VIDEO input jacks of your RF modulator by Audio/Video
cables.
5) Set your RF modulator’s channel 3/4 switch to either 3 or 4, whichever the TV channel is least used in your area. If your
RF modulator has a Modulator/Antenna switch, set it according to your RF modulator’s manual.
6) Turn on your TV and choose the same channel as you set the RF modulator’s channel 3/4 switch to.
For more details, follow the instructions supplied with the RF modulator.
Playing discs
TOLL FREE : 1-800-605-8453
or visit our web site at http://www.SylvaniaConsumerElectronics.com
Recording
INSTRUCCIONES EN ESPAÑOL INCLUIDAS
Getting started
DVR91DG
Connections
Recordable disc
• We strongly recommend using any DVD-R 8x, MAXELL DVD-R 16x and DVD-RW 4x
disc to assure good recording quality.
• Discs that have been tested and are proven to be compatible with this recorder:
VERBATIM DVD-R 8x VERBATIM DVD-RW 2x
MAXELL DVD-R 16x
JVC DVD-RW 4x
2006/02/15 17:25:53
Before you start
Precautions
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Laser Safety
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
The caution marking is located on the rear of the cabinet.
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this
device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modi-
fications to this equipment may cause harmful interference unless the modifications are expressly
approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
For Customer Use:
Read carefully the information located at the back of this unit and enter below the Model No. and Serial No. Retain
this information for future reference.
Model No. _____________________
Serial No. _____________________
EN
DVR91DG_E7A01UD.indd 2
2006/02/15 17:25:54
Before you start
IMPORTANT SAFEGUARDS
NFPA No. 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Editing
Changing the
Setup menu
Others
Español
DVR91DG_E7A01UD.indd 3
Playing discs
EN
Recording
14. Lightning - For added protection for this product during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with
them might be fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this product through any openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the product.
18. Servicing - Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance this indicates a need for service.
20. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
21. Safety Check - Upon completion of any service or repairs
to this product, ask the service technician to perform
safety checks to determine that the product is in proper
operating condition.
22. Heat - This product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Getting started
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
Connections
1. Read Instructions - All the safety and operating
instructions should be read before the appliance is
operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the
possibility of the loss of an authorization code for a CATV
converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. Attachments - Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this product near water,
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool,
and the like.
8. Accessories - Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the appliance. Use only with a cart,
stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting
of the appliance should follow the
manufacturer's instructions and
should use a mounting accessory
recommended by the manufacturer. An
appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
9. Ventilation - Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation
of the product and to protect it from overheating, and
these openings must not be blocked or covered. The
openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply
to your home, consult your appliance dealer or local
power company. For products intended to operate from
battery power, or other sources, refer to the operating
instructions.
11. Grounding or Polarization - This product is equipped with
a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/
Before you start
Precautions (cont’d)
2006/02/15 17:25:54
Before you start
Precautions (cont’d)
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit.
Do not place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid
places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the
ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong
magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the power cord immediately and take the unit to
our Authorized Service Center for servicing.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm
place or after heating a cold room or under conditions of high humidity. Do not use this unit at least
for 2 hours until its inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorized
by Macrovision, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Notice for progressive scan output
Consumers should note that not all high definition television sets are fully compatible with this
product and may cause artifacts to be displayed in the picture. In case of picture problems with 525
progressive scan output, it is recommended that the user switch the connection to the ‘standard
definition’ output. If there are questions regarding your TV set compatibility with this 525p DVD
recorder, please contact our customer service center.
Supplied Accessory
• Remote control
(NB075UD) with
two AA batteries
• RF cable
• Audio/Video cables • Owner’s Manual
(WPZ0901CAB01
(WPZ0102TM015
(1VMN22666)
or WPZ0901TM002) or WPZ0102LTE01)
• Quick Use Guide
(1VMN22667)
Owner's Manual
4
EN
DVR91DG_E7A01UD.indd 4
2006/02/15 17:25:55
Before you start
Before you start
Precautions (cont’d)
Maintenance
CLEANING THE CABINET
• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing
alcohol, spirits, ammonia or abrasive.
Getting started
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do
not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent,
abrasive cleaning agents or antistatic spray intended for analog records.
Connections
SERVICING
• Please refer to relevant topics on “Troubleshooting” on pages 72-75 before returning the product.
• If this unit becomes inoperative, do not try to correct the problem by yourself. There are no userserviceable parts inside. Turn off, unplug the power plug and please call our help line mentioned
on the front page to locate an Authorized Service Center.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you refer to the relevant sections and to
“Troubleshooting” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your
dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
Recording
DISC HANDLING
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is not used.
Playing discs
Changing the
Setup menu
• With an AM radio:
Tune an AM radio to a band with no broadcasting. Press a button on remote control toward the
radio. Sound will be fluttering when you press any key and the radio receives the signal. This
means the remote control unit is working.
• With a digital camera (including built-in camera of cellular phone):
Direct a digital camera to remote control, press and hold a button on remote control. If infrared
light appears through digital camera, the remote is working.
Editing
IR SIGNAL CHECK
If the remote control does not work properly, you can test if the remote control sends out the infrared
signal with AM radio or a digital camera (including built-in camera of cellular phone). It will help to
define the cause of malfunction.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks
of Dolby Laboratories.
DVR91DG_E7A01UD.indd 5
Español
EN
Others
Dolby Digital Recording
“Dolby® Digital Recording enables consumers to record high-quality video with stereo sound on
recordable DVD discs. The technology, when utilized instead of PCM recording, also saves recordable disc space, allowing for higher video resolution or extended recording time on each DVD.
DVDs created using Dolby Digital Recording will play back on all DVD-Video players.”
Note: This is true when the players are compatible with actual recordable DVD discs.
5
2006/02/15 17:25:56
Before you start
Table of contents
Before you start . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Symbol in this Owner’s Manual . . . . . . . . . . . . . . . 7
Functional overview . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing batteries in the remote control . . . . . . . 10
Using a remote control . . . . . . . . . . . . . . . . . . . . . 10
Display menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setup menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connections . . . . . . . . . . . . . . . . . . . . . . 13
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . . 13
Connection to a cable box or satellite box . . . . . 14
Connection to an Audio System . . . . . . . . . . . . . 15
Getting started . . . . . . . . . . . . . . . . . . . . 16
Easy DVD recording . . . . . . . . . . . . . . . . . . . . . . . 16
Initial setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Channel setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Getting channels automatically . . . . . . . . . . . . . . 18
Adding/deleting channels . . . . . . . . . . . . . . . . . . . 19
Selecting the TV stereo or SAP . . . . . . . . . . . . . . 20
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . 21
Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . 22
Setting the Daylight Saving Time . . . . . . . . . . . . . 23
Selecting the TV aspect ratio . . . . . . . . . . . . . . . . 23
Recording . . . . . . . . . . . . . . . . . . . . . . . . 24
Information on DVD recording . . . . . . . . . . . . . . . 24
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Recordable disc . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . 24
Restrictions on recording . . . . . . . . . . . . . . . . . . . 25
Information on copy control . . . . . . . . . . . . . . . . . 25
Making discs playable in other DVD player (Finalize) . . 25
Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . . . 26
Choosing the recording format of a blank disc . . 26
Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . 27
Setting for Auto Chapter . . . . . . . . . . . . . . . . . . . 27
Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
One-touch Timer Recording . . . . . . . . . . . . . . . . . 29
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Hints for Timer Recording . . . . . . . . . . . . . . . . . . 32
Settings for an external source . . . . . . . . . . . . . . 33
Connection to an external source . . . . . . . . . . . . 33
Recording from an external source . . . . . . . . . . . 34
Setting a disc to protect . . . . . . . . . . . . . . . . . . . . 34
Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . . . 35
Auto finalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Playing discs . . . . . . . . . . . . . . . . . . . . . 37
Information on DVD play . . . . . . . . . . . . . . . . . . . 37
Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . 37
Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Playing discs using the Disc menu . . . . . . . . . . . 40
Playing discs using the Title menu . . . . . . . . . . . 40
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Special playback . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Fast forward / Fast reverse . . . . . . . . . . . . . . . . . 41
Skipping TV commercials during play . . . . . . . . . 41
Rapid Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Step by step playback . . . . . . . . . . . . . . . . . . . . . 42
Slow forward / Slow reverse play . . . . . . . . . . . . 42
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . 44
Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Repeat/Random/Program playback . . . . . . . . . . . 46
Repeat playback . . . . . . . . . . . . . . . . . . . . . . . . . 46
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Selecting the format of audio and video . . . . . . . 47
Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . 47
Switching audio soundtrack . . . . . . . . . . . . . . . . . 48
Switching virtual surround system . . . . . . . . . . . . 48
Switching camera angles . . . . . . . . . . . . . . . . . . . 49
Reducing block noise . . . . . . . . . . . . . . . . . . . . . . 49
Editing . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Information on disc editing . . . . . . . . . . . . . . . . . 50
Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . 50
Editing discs in Video mode . . . . . . . . . . . . . . . . . 50
Editing discs in VR mode . . . . . . . . . . . . . . . . . . . 50
Editing discs in Video mode . . . . . . . . . . . . . . . . 51
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Putting names on titles . . . . . . . . . . . . . . . . . . . . 52
Setting or clearing chapter markers . . . . . . . . . . . 53
Editing discs in VR mode (Original) . . . . . . . . . . 54
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Setting titles to protect . . . . . . . . . . . . . . . . . . . . . 55
Releasing titles from protecting . . . . . . . . . . . . . . 56
Editing discs in VR mode (Playlist) . . . . . . . . . . . 57
Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Dividing a title . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Combining titles . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . 60
Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . 60
Editing discs in VR mode (Original / Playlist) . . 61
Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . 61
Putting names on titles . . . . . . . . . . . . . . . . . . . . 62
Setting or clearing chapter markers . . . . . . . . . . . 63
Setting pictures for thumbnails . . . . . . . . . . . . . . 64
Changing the Setup menu . . . . . . . . . . 65
Tour of the Setup menu . . . . . . . . . . . . . . . . . . . . 65
Language setting . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Display setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Audio setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Video setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Settings for Parental lock level . . . . . . . . . . . . . . 70
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Language code . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Frequently Asked Questions . . . . . . . . . . . . . . . . 76
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Español . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Limited Warranty . . . . . . . . . . . Back Cover
EN
DVR91DG_E7A01UD.indd 6
2006/02/15 17:25:56
Before you start
This DVD unit not only plays DVDs and CDs but also offers features for you to record to DVD discs and edit
them after that.
The following features are offered with this unit.
Unlike conventional interlace scanning, the progressive
scan system provides less flickering and images in higher
resolution than that of traditional television signals.
Symbol in this Owner’s Manual
Many functions of this unit are depending on the disc
type or the recording mode.
To specify for what disc type or recording mode
each function is, we put the following symbols at the
beginning of each item to operate.
Symbol
DVD-V
Video
VR
DVD-RW
DVD-R
CD
Available to DVD-Video discs
Available to DVD-RW in Video mode
Others
DVD-RW
Description
Changing the
Setup menu
Virtual Surround System:
You can enjoy stereophonic space through your exciting 2 channel stereo system.
Others
Progressive Scan system
Editing
Start to play from Original and Playlist:
Title playing is available from either an Original title or
Playlist.
Playing discs
Quick search for what you want to watch:
You can easily find the part you want to watch using
the search function. Search for a desired point on a
disc by title, chapter or time.
Recording
Play
Theater surround sound in your home:
When connecting the unit to an amplifier or a decoder
which is compatible with Dolby Digital, you are
allowed to experience the theater surround sound
from discs with surround sound system.
Compatibility
Available for playing discs recorded in Video
mode on a regular DVD player (Video mode):
Discs recorded in Video mode can be played on
regular DVD players, including computer DVD drives
compatible with DVD-Video playback*. You will need
to finalize the discs recorded in Video mode to play in
other DVD players.
* DVD-Video Format (Video mode) is a new format
for recording on DVD-RW/R discs that was approved
by the DVD Forum in 2000. Adoption of this format
is optional for manufactures of DVD playback devices
and there are DVD-Video players, DVD-ROM drives
or other DVD playback devices that do not play DVDRW/R discs recorded in the DVD-Video Format.
Getting started
Up to 8 program recording:
You can program the unit to record up to 8 programs,
with in a month in advance. Daily or weekly program
recordings are also available.
One-touch Timer Recording:
You can easily set a recording time as you prefer.
Every time [REC/OTR] is pressed during recording,
the recording time will be increased by 30 minutes up
to 8 hours. The unit will automatically turn off when
the recording time you set is reached.
Automatic Chapter marker setting:
Chapter markers will be put on recordings as you set
in the Setup menu before attempting to record.
Automatic Title menu making:
The unit makes title menus automatically when finalizing the disc which are recorded in Video mode.
Automatic Playlist making (VR mode):
A Playlist will be prepared from an Original title, so
that you can edit titles in a Playlist as you prefer.
An Original title is kept as it is.
Automatic finalizing (Video mode):
You can finalize discs after finishing all Timer
Recordings and at the end of the disc space automatically as you set in the Setup menu.
Left channel stereo recording:
This unit can record the sound of the Left channel
monaural input as Left and Right channels automatically (the input from the LINE 2 only).
Editing
Deleting titles:
You can delete titles which you do not need anymore.
Making your own Playlist:
With the original remains as it is, you can edit titles on
various Playlist as you prefer.
Putting names on titles
Setting pictures for thumbnails
Setting / clearing chapter markers
Dividing / combining titles
Deleting parts of titles, etc.
Protecting titles:
To avoid editing or erasing titles, the protect function
is useful when it is ON in the Original titles.
Connections
Recording
This unit is compatible with both DVD-RW, which is
rewritable repeatedly and DVD-R, which is available
for recording once. You can choose either one for
your convenience.
Before you start
Features
Available to DVD-RW in VR mode
Available to DVD-R discs
Available to Audio CDs
Español
EN
DVR91DG_E7A01UD.indd 7
2006/02/15 17:25:57
Before you start
Functional overview
2
1
Front Panel
3* 4 5 6 7 8*9
OPEN/CLOSE
CHANNEL
REC SPEED
(*) The unit can also
be turned on by
pressing these
buttons.
REV
FWD
15
7. STOP C button
2. Display
8. PLAY B button*
3. OPEN/CLOSE A button*
9. POWER button
Place a disc when open.
POWER
VIDEO
L AUDIO R
14 13 1211 10
Press to stop play or recording.
Refer to “Front Panel Display Guide” on page 12.
Press to start or resume play.
Press to open or close the disc tray.
Press to turn the unit on and off.
If timer programmings have been set, press to set the
unit in timer-standby mode.
4. CHANNEL L / K button
Press to change the channel up and down.
5. REV E button
During playback, press to skip to the previous chapter
or track.
During playback, press and hold for 1.5 seconds to
fast reverse.
When playback is paused, press to play reverse step
by step.
When playback is paused, press and hold for 1.5 seconds to slow reverse.
6. FWD D button
During playback, press to skip to the next chapter or track.
During playback, press and hold for 1.5 seconds to
fast forward.
When playback is paused, press to play forward step
by step.
When playback is paused, press and hold for 1.5 seconds to slow forward.
Rear Panel
PLAY
REC/OTR
S-VIDEO
1. Disc tray
STOP
1 2
3
VIDEO IN
IN
COMPONENT
VIDEO OUTPUT
S-VIDEO
IN
OUT
Use to connect external equipment with standard
audio cable.
11. VIDEO input jack (LINE2)
Use to connect external equipment with a standard
video cable.
12. S-VIDEO input jack (LINE2)
Use to connect the S-Video output of external equipment with an S-Video cable.
13. REC/OTR button
Press once to start a recording. Press repeatedly to
start a One-touch Timer Recording.
14. REC SPEED button
Press to switch the recording speed.
15. Remote control sensor
Receive signals from your remote control so that you
can control the unit from a distance.
4
VIDEO OUT
Y
L
OUT
10. AUDIO input jacks (LINE2)
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
L
PB/CB
R
ANTENNA
AUDIO IN
R
PR/CR
(L1)
11
1. ANTENNA IN jack
10 9 8 7
COAXIAL
AUDIO OUT
6
5
Use to connect an antenna.
2. VIDEO IN jack (LINE1)
Use to connect external equipment with a standard
video cable.
3. VIDEO OUT jack
Use to connect a TV monitor, AV receiver or other
equipment with a standard video cable.
4. AC Power Cord
7. COMPONENT VIDEO OUTPUT jacks
Use to connect a TV monitor with component video
inputs with component video cables.
8. S-VIDEO OUT jack
Use to connect the S-Video input of a TV monitor,
AV receiver or other equipment with an S-Video
cable.
9. S-VIDEO IN jack (LINE1)
Use to connect the S-Video output of external equipment with an S-Video cable.
Connect to a standard AC outlet to supply power to
this unit.
10. AUDIO IN jacks (LINE1)
Use to connect an AV receiver, Dolby Digital decoder
or other equipment with a coaxial digital input jack
with a digital coaxial cable.
11. ANTENNA OUT jack
5. COAXIAL DIGITAL AUDIO OUTPUT jack
6. AUDIO OUT jacks
Use to connect external equipment with standard
audio cable.
Use to connect an antenna cable to pass the signal
from the TV ANTENNA IN to your TV monitor.
Use to connect a TV monitor, AV receiver or other
equipment with standard audio cable.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent
damage to the unit.
• This unit does not have the RF modulator.
8
EN
DVR91DG_E7A01UD.indd 8
2006/02/15 17:25:57
Before you start
Remote Control
POWER
1
.@/:
3
6
5
DEF
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
13*
14
15
16
17
19
18
20
K
7
8
ABC
OPEN/CLOSE
{
B
L
9
11
12
Bx1.3/0.8
REC/OTR
REV
PLAY
FWD
h
B
g
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
C
22
24
21*
23
25
1.
4.
6.
Español
7.
EN
DVR91DG_E7A01UD.indd 9
Others
5.
Changing the
Setup menu
3.
8. REV E button
During playback, press to fast
reverse.
Or when playback is paused,
press to play slow reverse.
9. REC SPEED button
Press to switch the recording
speed.
10. B x1.3/0.8 button
During playback, press to playback in a slightly faster/slower
speed with keeping the audio
quality.
11. REC/OTR button
Press once to start a recording. Press repeatedly to start a
One-touch Timer Recording.
12. SKIP H button
During playback, press to skip to
the previous chapter or track. Or
when playback is paused, press to
play reverse step by step.
SKIP G button
During playback, press to skip to
the next chapter or track.
Or when playback is paused, press
to play forward step by step.
Editing
2.
POWER button
Press to turn the unit on and off.
If timer programmings have
been set, press to set the unit
in timer-standby mode.
ZOOM button
During playback, press to
enlarge the picture on the
screen.
Number buttons
Press to select channel numbers.
Press to select a title/chapter/
track on display.
Or press to enter values for the
settings in the Setup menu.
DISPLAY button
Press to display the On
Screen menu on or off.
TOP MENU button
Press to display the Title menu.
MENU/LIST button
Press to display the Disc menu.
To change Original and Playlist
on the TV screen.
(VR mode only)
Cursor K / L / { / B buttons
Press to select items or settings.
Playing discs
(*) The unit can also
be turned on by
pressing these
buttons.
Recording
10
REC SPEED
Getting started
4
TIMER
PROG.
Connections
2
ZOOM
13. OPEN/CLOSE A button*
Press to open or close the disc
tray.
14. TIMER PROG. button
Press to display the Timer
Programming list.
15. CH K / L buttons
Press to change the channel
up and down.
16. REPEAT button
Press to display the Repeat
menu.
17. SETUP button
Press to display the Setup
menu.
During DVD playback, press
and hold for more than 3 seconds to switch the progressive
scanning mode to the interlace
mode.
18. CLEAR button
Press to clear the password
once entered or to cancel the
programming for CD or to clear
the selecting marker number
in the marker setup mode or to
clear the program once entered
in the Timer Programming list,
etc.
19. ENTER button
Press to confirm or select
menu items.
20. RETURN
button
Press to return to the previously displayed menu screen.
21. PLAY B button*
Press to start or resume play.
22. FWD D button
During playback, press to play
fast forward.
Or when playback is paused,
press to play slow forward.
23. PAUSE F button
Press to pause play or recording.
24. CM SKIP button
During playback, press to skip
30 seconds.
25. STOP C button
Press to stop play or recording.
Before you start
Functional overview (cont’d)
9
2006/02/15 17:25:58
Before you start
Functional overview (cont’d)
Installing batteries in the remote control
Using a remote control
Install two “AA” size batteries (supplied) matching the
polarity indicated inside battery compartment of the
remote control.
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the
remote sensor of the unit.
• Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the unit.
• Replace the batteries when you notice a fall off in
the operating range of the remote control.
• The maximum operable ranges from the unit are
as follows.
- Line of sight: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m) within 15°
- Below: approx. 10 feet (3m) within 30°
1
2
3
Note:
Within about
23 feet (7m)
OPEN
/CLO
SE
CHAN
NEL
REV
REC
SPEE
D
FWD
REC/
OTR
STOP
PLAY
POWE
R
S-VID
EO
VIDEO
30°
POW
ER
DISP
CH
SPEE
D
PAUS
CLEA 7
R
E
REV
PQR
4
GHI
1
S
SPAC
E
0
8
TUV
CM
.@/:
5
JKL
9
SKIP
2
LAY
ABC
WXY 6
Z
MNO
TIME
PRO
G. R
3
DEF
R
30°
Y
PLA
P
NU/
ME AL
IGIN
STO
TOP
OR
D
FW
PLA
NU
LIS
ME Y
R
AUDI
O
IP
ENTE
L
SK
P
SE
CLO
EN/
OP
REC
REC
C OR
RENIT
Remote
control
MO
T
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe the
following:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together,
although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of
each battery match the indications in the battery
compartment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
Guide to Displays the On Screen menu
This unit uses the following the On Screen menu for most operations: Setup menu, Title list, Playlist, Original
and Display menu. They allow you to change the playing status of disc during play.
The Display menu also gives you information on the status of the disc.
Display menu
Press [DISPLAY] to call up the
Display menu. This menu will
give you the information on the
playing disc. Some operations are
available while disc is playing.
4
1
1
1
0:00:00
DVD-R
Video mode
CH
5
8
2
1. Indicates a disc type and a
format mode.
NOTE: In some descriptions on
this manual, only one disc type
is indicated as an example.
2. Indicates a channel number.
3. Indicates a recording mode and
possible recording time left.
4. Indicates a title number, chapter
number and the time lapse of
disc play.
5. Each icon means:
: Search
: Audio
: Subtitle
: Angle (except VR mode)
: Repeat
: Marker
: Noise Reduction
: Zoom
XP
6
1:01
3
: Surround
6. Indicates current disc status.
10 EN
DVR91DG_E7A01UD.indd 10
2006/02/15 17:25:59
Before you start
Setup menus
Press [SETUP] to display the Setup menu, then press [ENTER] to display each menu, using [K / L].
These menus provide entries to all main functions of the unit.
1
2
3
4
5
6
7
<DVD-R,DVD-RW (Video mode)>
Required Setting
Disc
Playback
Display
Recording
1
2
Format
Finalize
Clock
Channel
Disc
<DVD-RW (VR mode)>
Disc
Format
Finalize
Disc Protect OFF
ON
CD Playback Mode
4
5
Random Play
Program Play
Playing discs
<CD>
Recording
1
2
3
Getting started
Editing
Changing the
Setup menu
1.Required Setting:
To set up the required setting.
2.Playback:
To set up the unit to play
discs as you prefer.
3.Display:
To set up the OSD screen
and the front panel display of
the unit as you prefer.
4.Recording:
To set up the unit to record
to discs as you prefer.
5.Clock:
To set up the clock of the
unit as you need.
6.Channel:
To adjust the channel setting
of the unit as you prefer.
7.Disc / CD Playback Mode:
When a DVD-Video disc
(commercially available), a
new DVD-R disc is inserted
into the unit, you cannot
select “Disc”.
“CD Playback Mode” is
available only when an Audio
CD disc is inserted into the
unit.
1.Format (DVD-RW only):
Allows you to erase all of the
recorded content on the disc.
The disc will be completely
blank.
• Erased content cannot be
called back.
• A DVD-RW disc formatted
with this unit cannot be
used in other DVD recorders
without any recording using
this unit.
• If you want to use a disc
only formatted with this unit
on another DVD recorder,
you have to re-format the
disc on that recorder.
2.Finalize:
Allows you to finalize a disc
containing recorded titles.
3.Disc Protect (VR mode
only):
Allows you to protect a disc
from accidental editing or
recording.
4.Random Play:
To activate the random playback feature.
5.Program Play:
To activate the programmed
playback feature.
Connections
Setup
Before you start
Functional overview (cont’d)
Others
Español
EN
DVR91DG_E7A01UD.indd 11
11
2006/02/15 17:26:00
Before you start
Functional overview (cont’d)
Front Panel Display Guide
4
2
1
3
7
6
5
1. Current Status of the unit
:Appears when disc
playback is paused.
:Appears when playing a
disc.
:Appears when the timer
programming has been set
and is proceeding. Flashes
when all Timer Recordings
have been finished, or
when a program cannot be
performed by some reason.
:Appears during recording
process.
:Appears during repeat
play.
2. Disc type
4. Title / Track and Chapter mark
:Appears when an Audio
CD is inserted in the disc
tray.
:Appears when a DVD
disc is inserted in the
disc tray.
:Appears when a DVD-R
disc is inserted in the
disc tray.
:Appears when a DVDRW disc is inserted in the
disc tray.
:Appears when indicating a
title/track number.
:Appears when indicating a
chapter number.
5. Displays the following
• Playing time
• Current title / chapter / track
number
• Recording time/ remaining time
• Clock
• Channel number
• OTR (One-touch Timer
Recording) remaining time
6.
:Appears in the afternoon
with the clock displaying.
3. Recording speed
Indicates the recording speed of
the disc.
7.
:Appears when the
progressive scan system is
activated.
Display message
Appears when the unit
is turned on.
Appears when the disc
tray is closing.
Appears when the unit
is turned off.
Appears when a disc is
loaded on the disc tray.
Appears when the disc
tray is opening.
Appears when data is
being recorded on a disc.
12 EN
DVR91DG_E7A01UD.indd 12
2006/02/15 17:26:02
Connections
Before you start
Connection to a TV
Antenna
Cable
TV signal
Antenna
Cable
TV signal
(Back of TV)
VIDEO
AUDIO IN
(Back of TV)
or
or
COMPONENT
VIDEO OUTPUT
VIDEO IN
IN
2
1
OUT
Plug in the AC
power cord
of this unit.
VIDEO OUT
Y
L
L
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
PB/CB
Connect
Disconnect
S-VIDEO
IN
OUT
Connect
Audio
cable
(supplied)
Connections
3
Connect
RF cable
(supplied)
6
5
4
Connect
Video
cable
(supplied)
R
ANTENNA
R
PR/CR
AUDIO IN
(L1)
AUDIO OUT
COAXIAL
Make one of the following connections, depending on the capabilities of your existing equipment.
Method 1
Better picture
Basic Audio
Method 2
Best picture
COMPONENT
VIDEO IN
TV
R
Y
S-VIDEO IN
L
Recording
PB/CB
PR/CR
Audio cable
(supplied)
S-Video cable
(commercially available)
Component Video cable
(commercially available)
VIDEO OUT
VIDEO IN
OUT
OUT
VIDEO OUT
Y
COMPONENT
VIDEO OUTPUT
Y
L
L
OUT
S-VIDEO
IN
COMPONENT
VIDEO OUTPUT
S-VIDEO
IN
Playing discs
This unit
IN
L
PB/CB
R
ANTENNA
AUDIO IN
(L1)
R
PR/CR
AUDIO OUT
COAXIAL
R
PB/CB
AUDIO OUT
PR/CR
AUDIO OUT
After you have completed connections
S-VIDEO OUT
Getting started
(Back of this unit)
COMPONENT VIDEO OUT
Note
To set progressive scan mode, refer to pages 69-70
• This unit compatible with the Progressive Scan System. The feature provides you with the higher definition images
than the traditional output system does. To utilize this feature, you must set Progressive Scan mode to “ON”.
Changing the
Setup menu
• Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due
to the copy protection system.
• When Progressive Scan mode is selected, no video signal will be output from the VIDEO OUT or
S-VIDEO OUT jack.
Editing
• Switch the input selector on your TV to an appropriate external input channel (usually near channel 0). Press a button
on the TV’s original remote control (refer to “Input Mode Names for Common TV Brands” on page 15) that selects an
external input channel until the DVD recorder’s picture appears. Check your TV owner’s manual for details.
Others
Español
EN
DVR91DG_E7A01UD.indd 13
13
2006/02/15 17:26:02
Connections
Connection to a cable box or satellite box
(Back of TV)
VIDEO
(Cable box or
Satellite box)
IN
OUT
Connect
RF cable
(supplied)
VIDEO IN
1
Connect
COMPONENT
VIDEO OUTPUT
S-VIDEO
IN
RF cable
4
3
Connect
Video
cable
(supplied)
2
Cable
TV signal
AUDIO IN
IN
OUT
VIDEO OUT
Y
L
OUT
Connect
Audio
cable
(supplied)
L
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
PB/CB
R
ANTENNA
AUDIO IN
(L1)
R
PR/CR
AUDIO OUT
COAXIAL
(Back of this unit)
With this setup:
• You can record any unscrambled channel by selecting the channel on the cable box or satellite
box. Be sure that the cable box or satellite box is turned on.
• You cannot record one channel while watching another channel.
Note to the Cable TV System Installer :
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the
National Electrical Code, which provides guidelines for proper grounding - in particular, specifying
that the cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as possible.
14 EN
DVR91DG_E7A01UD.indd 14
2006/02/15 17:26:03
Connections
Before you start
Connection to an Audio System
• When you change the connections, all devices should be turned off.
• Refer to the operation manual accompanying external devices for more information.
Method 2
Stereo system
Dolby Digital decoder,
MD deck or DAT deck
Analog audio
input jacks
AUDIO
COAXIAL
Connections
Method 1
Digital audio
input jack
This unit
Getting started
Audio Coaxial
Digital cable
(commercially
available)
Audio cable
(supplied)
VIDEO OUT
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
L
R
AUDIO OUT
COAXIAL
Connecting to an MD deck or
DAT deck.
-
PCM
Playing discs
Setting Setup >Playback >Audio >Digital Out >
PCM
Dolby Digital
If output is Dolby Digital
Stream
encoded audio, connect to a
Dolby Digital decoder.
Unless connected to a Dolby
PCM
Digital decoder.
Connection
Recording
DIGITAL
AUDIO OUT
AUDIO OUT
* To complete these settings, refer to pages 68-69.
• Playing a DVD using incorrect settings may
generate noise distortion and may also damage
the speakers.
Note
Input Mode Names for Common TV Brands
(Refer to “After you have completed connections” on page 13 for this list.)
Panasonic
TV/VIDEO
Curtis Mathis
LINE1, LINE2, 00, 90, 91, 92, 93
RCA
INPUT, TV/VCR, 00, 90, 91, 92, 93
GE
INPUT, TV/VCR, 00, 90, 91, 92, 93
Samsung
TV/VIDEO
Hitachi
INPUT, AUX
Sanyo
VIDEO
JVC
VIDEO, VIDEO1, VIDEO2, VIDEO3
Sharp
00
Kenwood
AUX
Sony
VIDEO1, VIDEO2, VIDEO3
LXI-Series
00
Toshiba
TV/GAME
Magnavox
AUX CHANNEL
Zenith
00
Español
AUX
Others
Admiral
EN
DVR91DG_E7A01UD.indd 15
Changing the
Setup menu
• The audio source on a disc in a Dolby Digital Multi-channel
surround format cannot be recorded as digital sound by an
MD or DAT deck.
• By hooking this unit up to a Multi-channel Dolby Digital
decoder, you can enjoy high-quality Dolby Digital Multichannel surround sound as heard in the movie theaters.
• Playing a DVD using incorrect settings may generate noise
distortion and may also damage the speakers.
Editing
Note
15
2006/02/15 17:26:04
Getting started
Easy DVD recording
The following will help you to understand easily how to record to DVD discs.
Note:
Make sure batteries are in the remote control and you have connected this unit and the TV correctly.
Step 1: Choose a disc type.
Step 2: Insert a blank disc.
There are several types of recordable DVD discs to
choose from. Choose a recordable DVD disc type
based on your playing/recording/editing requirements. See “DVD disc types” at the bottom of
this page for more information on the differences
between the different kinds of compatible media.
This unit can record on the following type of
discs.
Remote Control
POWER
1
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
TUV
WXYZ
To turn onPQRS
OPEN/CLOSE
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
0
3
ENTER
TOP MENU MENU/LIST RETURN
(or)
2
To open
A
K
{
B
L
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
H
F
B
h
For example, when you want to record repeatedly on the same disc, or when you want to
edit the disc after recording, select the rewritable DVD-RW type disc.
When you want to save recordings without
any alteration, a non-rewritable DVD-R can be
your choice.
REC/OTR
POWER
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
STOP
OPEN/CLOSE
C
A
g
SKIP
G
CM SKIP
4
To close
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
FWD
Loading
This operation
may take a
K
{
while
to beB recognized.
L
REC SPEED
REV
h
Bx1.3/0.8
SKIP
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
DVD disc types
: Most suitable
: Can be used
Format the disc
: Some functions are limited
You want to
DVD-RW VR
: Cannot be used
DVD-RW Video
DVD-R
DVD-RW VR
DVD-RW Video
DVD-R
Rewritable?
Yes
Yes
No
Can create chapters at fixed intervals (auto.)
Yes
Yes
Yes
Can create chapters wherever you like (manual)
Yes
No
No
Can record 16:9 size pictures
Yes
Yes
Yes
Can record Copy-Once programs
Yes
No
No
Can perform basic edit functions
Yes
Yes
Yes
Can perform advanced edit functions (Playlist edit)
Yes
No
No
Record TV programs
Reuse by deleting unwanted contents
Edit recorded contents
Edit/Record from connected equipment
Copy discs for distribution
*1
Play on other DVD equipment
*1
Features
Recording
Editing
*1
DVD-RW (VR mode) can only be played on
DVD equipment that is VR compatible.
Note:
For details of the above functions and implied
restrictions, see the explanations inside the manual.
Insert the disc in the
recorder. Then, format the
disc from the Setup menu.
Video format (Video mode)
or Video recording format
(VR mode) will be available
depending on the disc type
inserted.
This is necessary to prepare the disc for recording. Details are on pages
26-27.
* When you format, the
entire contents on that
disc will be erased.
* The unit automatically
starts formatting when an
unused DVD-RW disc is
inserted.
16 EN
DVR91DG_E7A01UD.indd 16
2006/02/15 17:26:05
Getting started
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
Easy DVD recording (cont’d)
OPEN/CLOSE
A
.@/:
CH
Step 3: Select the
recording
speed.
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
POWER
REPEAT
SETUP
0
TOP MENU MENU/LIST RETURN
ENTER
Step 4: Select the
desired channel.
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
Connections
REV
PL AY
FWD
h
B
g
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
REC/OTR
A
K
POWER
B
C
TIMER
ZOOM
PROG.
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
L
Bx1.3/0.8
OPEN/CLOSE
Step 5: Record on DVD disc.
K
{
REC SPEED
TIMER
ZOOM
Before you start
POWER
OPEN/CLOSE
{
B
L
A
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
H
F
G
STOP
CM SKIP
B
h
CH
4
5
6
PQRS
TUV
WXYZ
REC/OTR
REPEAT
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
g
SKIP
C
Getting started
7
DISPLAY
FWD
0
K
CH
{
B
12
L
REC SPEED
Bx1.3/0.8
XP
REC/OTR
0:58
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
H
F
SKIP
G
STOP
CM SKIP
C
I
Hint 1: Play the recorded contents
Start Rec.
Title 1
What are titles and chapters?
The contents of DVD disc are generally
divided into titles. Titles may be further
divided into chapters.
Stop/Start
Stop Rec.
PROG.
.@/:
ABC
DEF
1
2
3
JKL
GHI
Title 2
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
Playing discs
You can select the title you want to play from
a displayed menu, and immediately start to
play. Recorded contents are easily accessible,
with simple procedure of choosing a title on a
chapter in the menu screen.
TIMER
ZOOM
Recording
POWER
0
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
Step 6: Stop the
K
recording.
{
B
L
Start Rec.
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Stop Rec.
H
Hint 2: Edit the recorded disc
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Editing
Trackconvenient
1 Track 2 Trackedit
3 Track
4 Track 5
You will find editing discs is easy. This unit offers
functions
which are possible only with DVD-RW/R discs.
You can edit the following from a title list.
Putting names on titles
Setting pictures for thumbnails
Setting / clearing chapter markers
Deleting titles or scenes
Changing the
Setup menu
•
•
•
•
(Possible editing functions depend on the recording format and editing method.)
Original and Playlist (VR mode)
You can edit the recordings in Playlist without changing the original recordings.
Playlist does not take up much disc space.
Wait for a moment.
90%
What “Original” or “Playlist” is for?
Finalizing a Disc
C
This operation may take
a while to be completed.
EN
DVR91DG_E7A01UD.indd 17
Español
• This will allow a disc that is recorded on this unit to be played back on a different
DVD player — without finalization it will not be playable on another player.
• After finalizing a disc if the recording was in Video mode, you cannot edit any
information that is on that disc.
• If you have recorded in VR mode on DVD-RW disc then editing is still
permitted after finalizing.
Others
Throughout this manual, you will find Original and Playlist to refer to the actual
content and the edited version.
• Original content refers to what’s actually recorded on the disc.
• Playlist content refers to the edited version of the disc; how the Original
content is to be played.
17
2006/02/15 17:26:06
Getting started
Initial setting
Turn on this unit for the first time,
you need to follow these steps.
1
Press [POWER].
2
4
Press [ENTER] to start Channel
Preset.
The unit will start getting channels
available in your area.
1
POWER
.@/:
“Initial Setting” will automatically
appear.
3
Using [K / L], select your
desired language for the OSD.
Then press [ENTER] to go to
next step.
Initial Setting
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
Turn the TV on. Select the input
to which the unit is connected.
Refer to the table on page 15.
TIMER
ZOOM
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH 1
0
Auto Presetting Now
5
3
4
5
K
{
After channel setting is finished,
“Clock Setting” will appear.
Then press [ENTER].
Initial Setting
B
L
REC SPEED
Bx1.3/0.8
REV
PL AY
h
B
SKIP
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Clock Setting
6
English
Follow to step 3 on page 22 to
“Manual Clock Setting”.
Français
Español
Channel setting
If you have changed antenna
connection, we recommend you
to program available channels
in your area with the following
procedures.
Getting channels
automatically
1
Press [SETUP].
2
Using [K / L], select “Channel”.
Press [ENTER].
Channel menu will appear.
3
Using [K / L], select “Auto
Preset”. Press [ENTER].
The unit will start getting channels
available in your area.
4
Press [SETUP] to exit.
Setup
Required Setting
Playback
• You can select only the
channels memorized in this unit
by using [CHANNEL L / K] or
[CH K / L].
Display
Recording
Clock
Channel
Disc
POWER
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
1
4
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
2
3
K
{
B
L
REC SPEED
Bx1.3/0.8
REC/OTR
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
H
F
SKIP
G
STOP
CM SKIP
C
To select a channel
You can select a channel by directly entering channel using the Number buttons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.
(For example: 117, press [1], [1], [7])
• You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).
• You can select the line input mode (“L1” or “L2”). To select “L1” by pressing [0], [0], [1]. To select “L2” by
pressing [0], [0], [2]. Details are on pages 33-34.
Note
• If the auto presetting is canceled during presetting, some channels not yet preset may not be received.
• The selection will depend on how you receive the TV channels.
Press [RETURN
] or [SETUP] to cancel the auto presetting during scanning.
18 EN
DVR91DG_E7A01UD.indd 18
2006/02/15 17:26:07
Getting started
Before you start
Channel setting (cont’d)
Adding/deleting
channels
1
Select the channel number to
add or delete.
Press [{] or [CH L] to move to a
lower channel number.
Press [B] or [CH K] to move to a
higher channel number.
Press the Number buttons to
select a channel number directly.
Press [SETUP].
POWER
.@/:
4
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
1
6
REPEAT
0
Manual Preset
K
CH
Using [K / L], select “Channel”.
Press [ENTER].
Channel menu will appear.
7
Add
Delete
{
REC SPEED
REV
Bx1.3/0.8
SKIP
h
3
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Using [K / L], select “Manual
Preset”. Press [ENTER].
Manual Preset menu will appear.
Manual Preset
2
Add
Delete
5
Playing discs
CH
• [CH K / L] works on the
memorized channel in this unit.
• [{ / B] works on all of channel
numbers.
Recording
2
3
4
5
B
L
Getting started
2
Connections
The channels you no longer
receive or seldom watch can
be deleted from the memory.
You also may add channels into
memory.
4
Using [K / L], select “Add” or
“Delete”. Press [ENTER].
The channel number will be
added or deleted from the channel
memory. Then the next channel
number will appear so that you
can continue adding or deleting
channels.
Editing
6
Press [SETUP] to exit.
Changing the
Setup menu
Others
Español
EN
DVR91DG_E7A01UD.indd 19
19
2006/02/15 17:26:08
Getting started
Selecting the TV stereo or SAP
You can select a sound channel
to output from TV. “Stereo” has
been selected as the default.
1
Press [SETUP].
3
Using [K / L], select “TV Audio
Select”. Press [ENTER].
Option window will appear.
2
POWER
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
TV Audio Select
.@/:
1
2
3
Stereo
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
SAP
Using [K / L], select “Required
Setting”. Press [ENTER].
Required Setting menu will appear.
CH
REPEAT
0
Required Setting
K
Select Video
TV Aspect
4:3 Letter Box
TV Audio Select
Stereo
{
B
L
4
Using [K / L], select “Stereo” or
“SAP”. Press [ENTER].
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
1
5
2
3
4
C
Stereo:
Outputs main audio.
SAP (Secondary Audio Program):
Outputs sub audio.
5
Press [SETUP] to exit.
Notes on TV channel audio
• When you record a TV program available in second audio or stereo
on a DVD-RW/R, you have to select either Stereo or SAP in the
Channel Preset screen beforehand. Refer to the following table to
check an appropriate setting.
Selected
audio
Stereo
SAP
Broadcast
audio
Disc
recording
Audio
output
STEREO+SAP STEREO
STEREO
STEREO
STEREO
STEREO
MONO+SAP
MONO
MONO
MONO
MONO
MONO
STEREO+SAP SAP
SAP
STEREO
STEREO
STEREO
MONO+SAP
SAP
SAP
MONO
MONO
MONO
• You can only play the disc in second audio if a TV program is
available in second audio and you set “ TV Audio Select ” to “ SAP ”.
20 EN
DVR91DG_E7A01UD.indd 20
2006/02/15 17:26:08
Getting started
Before you start
Setting the clock
Auto Clock Setting
• If you do not know your PBS
channel number:
Using [K / L], select “Auto”.
Press [ENTER].
The setting will be activated.
6
• If you know your PBS channel
number:
Using [K / L], select
“Manual”. Press [ENTER].
POWER
.@/:
PROG.
ABC
DEF
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Auto
Manual
B
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Using the Number buttons
or [K / L], enter your PBS
channel number. Press
[ENTER].
The setting will be activated.
Playing discs
OFF
PL AY
PAUSE
Recording
Auto Clock Setting
2
3
4
B
1
Press [SETUP].
Using [K / L], select “Auto
Clock Setting”. Press [ENTER].
Option window will appear.
1
5
REPEAT
L
H
3
CH
K
{
REC/OTR
Using [K / L], select “Clock”.
Press [ENTER].
Clock menu will appear.
A
GHI
Auto Clock Setting - Manual
1
2
OPEN/CLOSE
0
Set Channel No.
CH
TIMER
ZOOM
Getting started
Make sure
• The antenna/Cable TV
connections are correct.
• If this unit is connected to a
Cable Box or Satellite Box,
select the local PBS station
on them to set the clock
automatically.
4
Connections
Set the clock before you try the Timer
Programming. If a Public Broadcasting
Station (PBS) is available in your area,
follow “Auto Clock Setting” below. If
not, follow “Manual Clock Setting” on
page 22.
• If you want to set the clock
manually and cancel the Auto
Clock Setting function: Using
[K / L], select “OFF”. Press
[ENTER].
The Auto Clock Setting function
will be canceled.
Editing
5
Press [SETUP] to exit.
6
Changing the
Setup menu
Press [POWER] to turn off the
unit.
This unit will search for the time
only when the power is off. Leave
it off for several minutes to give
this unit time to set the clock on
the front display panel.
Note
DVR91DG_E7A01UD.indd 21
Español
EN
Others
• The clock may set itself
automatically after you connect
the antenna/cable signal to
this unit and plug in the power
cord. In this case, the current
time will appear on the front
panel display.
• If the current time is not
displayed or the displayed
clock is not correct, set the
clock manually.
21
2006/02/15 17:26:09
Getting started
Setting the clock (cont’d)
Manual Clock Setting
1
Press [SETUP].
4
Using [K / L], enter the date
(month / day / year).
Press [{ / B] to move the cursor.
2
POWER
.@/:
Clock Setting
Using [K / L], select “Clock”.
Press [ENTER].
JAN/ 01 / 2006(SUN)
12: 00 AM
3
---- / -- / ---- ( ---- )
-- : -- --
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
Using [K / L], select “Clock
Setting”. Press [ENTER].
Clock Setting menu will appear.
Clock Setting
TIMER
ZOOM
K
{
B
L
5
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Using [K / L], enter the time
(hour / minute). Press [{ / B].
A cursor will move on AM.
H
REC/OTR
PL AY
B
PAUSE
g
SKIP
F
G
STOP
CM SKIP
C
Clock Setting
FWD
1
7
2
3
4
5
6
JAN/ 02 / 2006(MON)
12: 00 AM
Press [ENTER] again.
Default date will appear.
6
Press [K / L] to select “AM” or
“PM”. Press [ENTER].
The settings will be activated.
Although seconds are not displayed, they begin counting from
zero.
7
Press [SETUP] to exit, if Clock
menu appears.
Note
• Your clock setting will be lost if
either there is a power failure
or this unit has been unplugged
for more than 30 seconds when
you set the clock manually.
22 EN
DVR91DG_E7A01UD.indd 22
2006/02/15 17:26:09
Getting started
Before you start
Setting the clock (cont’d)
Setting the Daylight
Saving Time
3
Using [K / L], select “Daylight
Saving Time”. Press [ENTER].
Option window will appear.
POWER
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
Daylight Saving Time
.@/:
1
2
3
ON
GHI
JKL
MNO
OFF
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
1
5
REPEAT
0
2
3
4
K
Press [SETUP].
{
4
2
Using [K / L], select “ON” or
“OFF”. Press [ENTER].
Choose “ON” when currently
observing the daylight saving time.
Using [K / L], select “Clock”.
Press [ENTER].
Clock menu will appear.
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Recording
5
Press [SETUP] to exit.
.@/:
3
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
1
5
REPEAT
0
TV Aspect
4:3 Letter Box
{
B
L
16:9 Wide
Press [SETUP].
REC SPEED
Bx1.3/0.8
2
REV
PL AY
h
B
SKIP
H
REC/OTR
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Refer to the Note on this page.
Using [K / L], select a desired
option. Press [ENTER].
5
Press [SETUP] to exit.
Note
EN
DVR91DG_E7A01UD.indd 23
Español
If you have a standard TV:
Select “4:3 Letter Box”, so
that black bars appear on the
top and bottom of the screen.
Select “4:3 Pan & Scan” for
a full height picture with both
sides trimmed.
If you have a widescreen TV:
Select “16:9 Wide”.
Others
4
Changing the
Setup menu
2
3
4
K
4:3 Pan & Scan
Editing
Using [K / L], select “TV
Aspect”. Press [ENTER].
Option window will appear.
1
Using [K / L], select “Required
Setting”. Press [ENTER].
Required Setting menu will
appear.
POWER
Playing discs
Selecting the TV aspect ratio
You can select the TV aspect ratio
to match the formats of what you
are playing with the unit and your
TV screen (4:3 standard or 16:9
widescreen TV).
“4:3 Letter Box” has been selected
as the default.
Getting started
1
Connections
When “Daylight Saving Time” is
“ON”, the unit clock will automatically move forward one hour at
2:00a.m. on the first Sunday in
April and move back one hour at
2:00a.m. on the last Sunday in
October.
“ON” is selected as a default.
23
2006/02/15 17:26:10
Recording
Information on DVD recording
Information
Recording speed
This unit can record to DVD-R and DVD-RW discs.
DVD-R discs can only be recorded once, and cannot
be erased. DVD-RW discs can be recorded and
erased many times.
DVD-R discs can only be recorded in Video mode,
while DVD-RW discs can select a recording format
between Video mode and VR mode.
You can select a recording speed among 6 options,
and the recording time will depend on the recording
speed you select as follows.
* Discs recorded in SLP or SEP on this recorder
may not be played back on other DVD
recorders or DVD players.
Logo
DVD-RW
Attributes
Disc Size
8cm/12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB) (for 12cm)
180 minutes (1.4GB) (for 8cm)
8cm Disc
Disc type
Disc format
Functions
Video mode
Playing, limited
recording, limited editing
Video
DVD-RW
DVD-RW
VR mode
VR
DVD-RW
Video mode
DVD-R
DVD-R
Playing, recording,
Original/Playlist editing
Playing, limited
recording, limited
editing
18 min
SP (2H)
36 min
LP (4H)
72 min
EP (6H)
108 min
SLP (8H)
144 min
(good)
(poor)
XP (1H)
60 min
(good)
SP (2H)
120 min
12cm Disc LP (4H)
EP (6H)
240 min
SLP (8H)
480 min
Recordable disc
DVD players with are capable of playing
DVD-RW recorded in VR mode.
XP (1H)
SEP (10H) 180 min
DVD-R
• We strongly recommend using any DVD-R 8x,
MAXELL DVD-R 16x and DVD-RW 4x disc to
assure good recording quality.
• Discs that have been tested and are proven to be
compatible with this recorder:
VERBATIM DVD-R 8x VERBATIM DVD-RW 2x
MAXELL DVD-R 16x
JVC DVD-RW 4x
• About Video mode and VR (Video Recording)
mode:
Video mode is the same recording format as
DVD-Video discs purchased locally, so that you
can play in most DVD players. To play in other
DVD players, you will need to finalize (see
page 35). Unless finalized, you can play, record
additionally or edit discs recorded in Video
mode with this unit.
VR (Video Recording) mode is a basic
recording format for DVD-RW. You can record
and edit repeatedly.
Recording Recording Video/Sound
Quality
speed
time
360 min
(poor)
SEP (10H) 600 min
• The recording time are estimates and actual
recording time may differ.
• The audio and video quality is getting poorer as
the Recording time becomes longer.
• Each time [REC SPEED] is pressed, recording
speed and its allowed recording time will be
displayed.
Note
• This recorder cannot record CD-RW or CD-R
discs.
• DVD-RW/R and CD-RW/R discs recorded on a
personal computer or a DVD or CD recorder may
not play if the disc is damaged or dirty or if there
is dirt of condensation on the player’s lens.
• If you record a disc using a personal computer,
even if it is recorded in a compatible format, there
are cases in which it may not play because of the
settings of the application software used to create
the disc. (Check with the software publisher for
more detailed information.)
• Discs recorded in Video mode on this unit cannot
record additionally using other DVD recorders.
• A DVD-RW disc formatted with this unit cannot be
used in other DVD recorders without any recording
using this unit.
• Since the recording is made by the variable bit rate
(VBR) method, depending on the picture you are
recording, the actual remaining time for recording
may be a little shorter than the remaining time
displayed on the OSD.
24 EN
DVR91DG_E7A01UD.indd 24
2006/02/15 17:26:11
Recording
Restrictions on recording
After finalizing:
• Once DVD-RW/R (Video mode) is finalized, you
cannot record additionally or edit.
• Even if DVD-RW (VR mode) is finalized, you can
record additionally or edit the disc.
• When DVD-RW/R (Video mode) is finalized, the
Title menu will be created automatically.
To play in other DVD players, finalize discs
recorded on this unit.
Playable
OPEN/CLOSE
CHANNEL
REC SPEED
REV
FWD
PLAY
POWER
REC/OTR
S-VIDEO
VIDEO
L AUDIO R
DVD player
Not Playable
Playing discs
Information on copy control
VR
DVD-RW
Video
DVD-R
Copy
-once
Copyprohibited
ver.1.1,1.2
ver.1.1,1.2 CPRM compatible
ver.1.1,1.2
ver.1.1,1.2 CPRM compatible
Changing the
Setup menu
DVD-RW
Copy
-free
Editing
Some satellite broadcasts include copy-protected
information. For recording these, refer to the
following.
Disc type / format
Recording
This Unit
STOP
Getting started
What is “CPRM”?
CPRM is a copy protection system with
scramble system regarding the recording of
“copy-once” broadcast programs. CPRM stands
for Content Protection for Recordable Media.
This unit is CPRM compatible, which means that
you can record copy-once broadcast programs,
but you cannot then make a copy of those
recordings. CPRM recordings can only be made
on DVD-RW discs formatted in VR mode, and
CPRM recordings can only be played on DVD
players that are specifically compatible with
CPRM.
After recording, you must finalize the disc in order to
play on other units. (Refer to page 35.)
Connections
You cannot record copy-protected video using this
unit. Copy-protected video includes DVD-Video discs
and some satellite broadcasts.
If copy-protected material is encountered
during a recording, recording will pause or stop
automatically and an error message will be
displayed on the screen.
Video that is “copy-once only” can only be
recorded using a DVD-RW disc in VR mode with
CPRM (see below).
When recording a TV broadcast or through an
external input, you can display copy control
information on the screen.
Making discs playable in other DVD
player (Finalize)
Before you start
Information on DVD recording (cont’d)
ver.2.0
Recordable
Not Recordable
Others
Español
EN
DVR91DG_E7A01UD.indd 25
25
2006/02/15 17:26:11
Recording
Formatting a disc
Choosing the recording format of a blank disc
Video
DVD-RW
VR
DVD-RW
When inserting a blank disc, the
unit automatically starts to initialize
the blank disc. You have to select
your desired format before inserting the blank disc.
5
POWER
Using [K / L], select “Video
mode” or “VR mode”. Press
[ENTER].
The recording format will be set.
1
6
2
7
.@/:
Press [SETUP] to exit.
Press [SETUP].
Using [K / L], select “Disc”.
Press [ENTER].
Disc menu will appear.
<VR mode>
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
K
Insert a blank disc.
Formatting will start.
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
REC/OTR
PL AY
B
PAUSE
g
SKIP
F
G
STOP
CM SKIP
C
Disc
FWD
1
6
2
3
4
5
Format
Finalize
Disc Protect OFF
ON
Formatting
90%
8
Formatting is completed.
“100%” will be indicated.
3
Using [K / L], select “Format”.
Press [ENTER].
Format menu will appear.
Format
Start
Format Mode
Video mode
4
Using [K / L], select “Format
Mode”. Press [ENTER].
Format - Format Mode
Video mode
VR mode
Video mode
DVD Player Compatibility mode.
VR mode
Editing possibility mode.
“Video mode” has been selected
as the default.
Note
• The recording format setting
is effective only for DVD-RW
discs. You cannot change the
recording format on a DVD-R
disc. DVD-R discs will always
be in Video mode.
• You cannot mix two formats
on one DVD-RW disc.
When you load a disc
once recorded before, the
recording format cannot
be changed even if you
change it in the Setup
menu.
• When inserting a blank
DVD+RW or DVD+R disc, the
error message (“Disc Error”)
will appear. This unit is not
compatible with a DVD+RW/R
disc.
• Playlist will be created
automatically when recording
on DVD-RW in VR mode.
• A blank chapter may be
created depending on the
remaining time of the disc.
26 EN
DVR91DG_E7A01UD.indd 26
2006/02/15 17:26:13
Recording
Before you start
Formatting a disc (cont’d)
Reformatting a disc
Video
DVD-RW
Final confirmation window will
appear.
VR
DVD-RW
.@/:
Format
Start
Format mode
1
Video mode
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
OPEN/CLOSE
A
CH
REPEAT
CLEAR
SETUP
Yes
0
No
TOP MENU MENU/LIST RETURN
ENTER
Are you sure?
Press [SETUP].
TIMER
ZOOM
2
3
4
5
K
Using [K / L], select “Disc”.
Press [ENTER].
Disc menu will appear.
3
Using [K / L], select “Format”.
Press [ENTER].
Format menu will appear.
{
B
L
5
REC SPEED
Using [K / L], select “Yes”.
Press [ENTER].
Formatting will start.
Bx1.3/0.8
REV
PL AY
h
B
SKIP
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Recording
Format
Start
Format Mode
Video mode
Formatting
90%
Formatting is completed.
“100%” will be indicated.
Using [K / L], select “Start”.
Press [ENTER].
This operation may take a while
to be completed.
• When you reformat the disc,
the contents of the disc will
be erased.
• If you want to cancel format at
step 4 or 5, select “No”.
Video
DVD-RW
VR
DVD-RW
Option window will appear.
Auto Chapter
You can set a specified time for
chapter marks.
OFF
5 minutes
Press [SETUP].
Using [K / L], select “Auto
Chapter”. Press [ENTER].
ABC
DEF
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
1
5
REPEAT
15 minutes
7
8
9
30 minutes
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
2
3
4
K
“10 minutes” has been selected as
the default.
4
Using [K / L], select a desired
time option. Press [ENTER].
{
B
L
REC SPEED
Bx1.3/0.8
REV
PL AY
h
B
SKIP
H
REC/OTR
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Others
3
PROG.
GHI
60 minutes
2
Using [K / L], select
“Recording”. Press [ENTER].
.@/:
TIMER
ZOOM
Changing the
Setup menu
1
10 minutes
POWER
Editing
Setting for Auto Chapter
Playing discs
Note
6
4
Getting started
2
1
Connections
If you are using a DVD-RW disc, by
default it will be Video mode. You
can change it to VR mode from the
Setup menu.
POWER
5
Español
Press [SETUP] to exit.
EN
DVR91DG_E7A01UD.indd 27
27
2006/02/15 17:26:13
Recording
Basic recording
Video
DVD-RW
VR
DVD-RW
DVD-R
Follow the steps below to record
TV programs.
1
Press [POWER].
Turn the TV on and be sure to
select the input to which the unit is
connected.
2
Press [OPEN/CLOSE A].
The disc tray will open.
7
Press [REC/OTR] to start
recording.
“I” mark will be displayed for 5
seconds.
Insert your disc with its label facing up. Align the disc to the disc
tray guide.
6
I
TIMER
ZOOM
PROG.
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
2
4
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
Press [PAUSE F] to resume.
Press [PAUSE F] or [REC/OTR]
again to start recording again.
K
{
8
3
1
POWER
B
L
Press [STOP C] to stop recording.
This operation may take a
while to be completed.
5
7
REC SPEED
Bx1.3/0.8
REC/OTR
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
C
7
8
disc tray
guide
4
Press [OPEN/CLOSE A] to close
the disc tray.
This operation may take a
while to be recognized.
5
Using [REC SPEED], select a
recording speed.
XP
0:58
Refer to “Recording speed” on
page 24.
6
Using [CH K / L] or the Number
buttons, select a desired channel to record.
CH
12
Note
• Recording starts immediately
and continues until the disc is
full or you stop recording.
• When the clock setting has
not been made, the space for
a date and time of title names
in the Original list or Playlist
will be blank.
• When you record a TV
program which has Stereo
and SAP audio on a DVDRW/R, you have to select the
TV channel audio (Stereo or
SAP) beforehand. Only the
selected channel audio will be
recorded. Refer to “Selecting
the TV stereo or SAP” on
page 20 for more details.
• You cannot mix two formats
on one DVD-RW disc.
When you load a disc
once recorded before, the
recording format cannot
be changed even if you
change it in the Setup
menu.
• You cannot change the
recording speed during the
REC pause mode.
• You can change a channel
during the REC pause mode.
28 EN
DVR91DG_E7A01UD.indd 28
2006/02/15 17:26:14
Recording
Before you start
One-touch Timer Recording
Video
DVD-RW
VR
DVD-RW
DVD-R
4
Press [REC/OTR] repeatedly to
select desired recording time.
Recording times appear on the TV
screen (30 minutes to 8 hours).
Recording will start.
POWER
3
1
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
Connections
This is a simple way to set the
recording time in blocks of 30
minutes. Check that the disc you
are recording onto has enough
space for the time you set.
When the recording finishes the
recorder automatically goes into
standby.
CH
REPEAT
0
This operation may take a
while to be recognized.
Using [REC SPEED], select a
recording speed.
Refer to “Recording speed” on
page 24.
Using [CH K / L] or the Number
buttons, select a desired channel to record.
2
0:30
(Normal Recording) 1:00
8:00
B
L
0:30
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
4
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
4
C
7:30
When the unit reaches the
specified time, it will be turned off
automatically.
Playing discs
3
I
Recording
2
K
{
To change the recording length
during the One-touch Timer
Recording, press [REC/OTR]
repeatedly until the desired length
appear.
This operation may take a
while to be completed.
Note
Español
DVR91DG_E7A01UD.indd 29
Others
EN
Changing the
Setup menu
• The remaining recording
time will appear on the
display panel during a Onetouch Timer Recording.
Press [DISPLAY] to see it
on the TV screen.
• You cannot pause a Onetouch Timer Recording.
• Unlike a Timer Recording,
you can perform the following
operations during a One-touch
Timer Recording.
-Turning the power off
-Using [REC/OTR] and
[STOP C]
• The unit will be turned off
automatically under the
following conditions.
1)No space remained on the
disc
2)When a power failure occurs
Editing
To cancel the One-touch Timer
Recording within the specified
time, press [STOP C] .
Getting started
Turn on the unit and load a
recordable disc.
Make sure that the TV input is set
on the unit.
29
2006/02/15 17:26:14
Recording
Timer Recording
Video
VR
DVD-RW
DVD-RW
DVD-R
You can program the unit to record
up to 8 programs within a month in
advance. Daily or weekly program
recordings are also available.
• Be sure to set the clock before
setting a timer programming.
• Insert a recordable disc.
1
Press [TIMER PROG.].
Timer Programming list will appear.
Timer Programming
Date
2
Start
End
CH
4
Using [K / L], enter the Start
and End. Press [B].
Timer Programming
Date
1. JAN/01
5
---
5.
---
6.
---
7.
---
4
5
6
8.
---
PQRS
TUV
WXYZ
1. JAN/01
4.
---
2.
---
5.
---
3.
---
6.
---
7.
---
8.
---
Date
4.
1. JAN/01
2.
---
3.
---
4.
---
5.
---
6.
---
--:--
L1
Start
End
12:57AM
1:57AM
CH
CH
ABC
DEF
1
2
3
JKL
MNO
A
1
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
Speed
K
8
{
6
8.
B
L
---
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
H
F
G
STOP
CM SKIP
h
REC/OTR
---
B
C
Using [K / L], select a recording
speed.
FWD
g
SKIP
2
3
4
5
6
Timer Programming
Date
--:--
.@/:
OPEN/CLOSE
0
5.
--To record
from external input,
6.
--select
L1
or
L2.
7.
---
Timer Programming
Speed
PROG.
Timer Programming
---
CH
TIMER
ZOOM
GHI
Using [K / L], select the channel
number to record. Press [B].
---
End
POWER
4.
3.
Start
Speed
---
2.
Date
L1
---
Speed
Using [K / L], enter the Date.
Press [B].
CH
--:--
3.
---
3
End
2.
1.
Using [K / L], select a program
number. Press [ENTER].
Start
12:57AM
1. JAN/01
2.
---
3.
---
4.
---
7.
---
8.
---
Start
End
12:57AM
1:57AM
CH
CH
Speed
8
1H
Refer
5. to
--- “Recording speed” on
--page6. 24.
When
pressing [L] at the
7.
--8.
--current
date, The Date will
change as follows.
e.g. January 1st
JAN/01
L
Daily
L
MON-SAT
L
MON-FRI
L
SAT
L
L
L
FRI
SUN
L
JAN/31
Note
• If you have not set the clock
yet:
A manual clock setting menu
will appear instead of the
Timer Programming list at
step 1. Continue with step 2
in “Manual Clock Setting” on
page 22 before setting a timer
programming.
• Press [s / B] to move the
cursor to the left and the right in
the Timer Programming list.
• After step 8, the recording will
start immediately before the
recording time you set.
30 EN
DVR91DG_E7A01UD.indd 30
2006/02/15 17:26:16
Recording
Before you start
Timer Recording (cont’d)
8
7
Press [POWER].
indicator disappears from the
front panel display.
Press [TIMER PROG.].
Timer Programming list will appear.
Timer Programming
Date
1. JAN/01
---
3.
---
4.
---
5.
---
End
12:57AM
1:57AM
CH
CH
Speed
8
1H
6.
--Check
the information on the
7.
--list8.you
--- will need.
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
7
K
the timer programming
{
B
L
4
To clear the timer programming:
Using [K / L], select your
desired program. Press
[CLEAR].
1
6
To correct the timer programming:
Using [K / L], select your desired
program. Press [ENTER].
Next, correct the timer programming
by using [K / L / { / B].
Finally, press [ENTER] again.
REV
POWER
Bx1.3/0.8
h
REC/OTR
.@/:
PL AY
FWD
B
H
F
ABC
STOP
DEF
CM SKIP
SKIP
ZOOM
PAUSE
PROG.
2
5
g
OPEN/CLOSE
SKIP
A
G
TIMER
1
2
C
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
4
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Note
5
REC SPEED
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
6
Press [POWER] to return to the
timer standby mode.
To stop the Timer Recording in process
Each error number means:
Timer Programming
Date
* JAN/01
---
3.
---
4.
---
5.
---
6.
---
7.
---
8.
---
Start
End
12:57AM
1:57AM
CH
CH
Speed
8
E22
Press [CLEAR] to erase the
selected program.
E1-22
E37-39
Recording error other than
below
E35
PCA full
E36
E23-24
Unrecordable disc
Already finalized Video
format disc
E25-28
Copy prohibited program
E40
Some portion has not
been recorded because
of program overlapping.
Recording did not start at
the start time.
E29
Disc protected
E30
Disc full
E31-32
Already 99 titles recorded
E33
Already 999 chapters
recorded
E41
Power failed
E34
No space for Control
information
E42
No disc when recording
EN
DVR91DG_E7A01UD.indd 31
Español
• A program with the error number is grayed and asterisked in the Timer Programming list.
• Once the Timer Programming list with error line(s) is displayed, or after canceling and setting again the timer
standby mode, the program line(s) with error will be cleared.
Others
2.
Changing the
Setup menu
Press [STOP C] on the front panel of the unit.
[STOP C] on the remote control is not effective.
If the timer program did not complete correctly, the error number
appears in the Timer Programming list.
Editing
• Press [TIMER PROG.] to
check the timer programming
in process.
When the Timer Recording is
proceeding, that program will
be highlighted in red.
C
Press [TIMER PROG.] to exit.
Playing discs
3
2.
Start
.@/:
TIMER
ZOOM
Recording
2
8
POWER
Getting started
1
Press [POWER] to set a Timer
Programming.
indicator will appear on the
front panel display.
Connections
Press [ENTER] when
information is entered. Your
program setting will be stored.
• To set another program, repeat
steps 2 to 7.
• To exit, press [TIMER PROG.]
or [SETUP].
• When two or more programs are
overlapped, “Overlap” and the
overlapped program number will
appear on the TV screen.
Checking, canceling, or correcting
information
31
2006/02/15 17:26:17
Recording
Timer Recording (cont’d)
Hints for Timer Recording
• If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and
all timer programming will be lost.
• If a disc is not on the tray, the indicator flashes and Timer Recording cannot be performed. In some
cases, the indicator appears momentarily around the start point as the unit attempts to record. Please
insert a recordable disc.
• When all the Timer Recording is completed, the indicator flashes. To play or eject the recorded disc,
press [POWER] first, and then press [PLAY B] or [OPEN/CLOSE A].
• During the Timer Recording or timer standby ( indicator is on the front panel display), any operations
on the unit will not be available. To make these operations available, cancel the Timer Recording or timer
standby first ( indicator disappears).
• To cancel the timer standby mode, press [POWER].
• When the Start and the End time are the same, the length of the recording will be set for 24 hours. When
the disc reaches at the end during the recording, the unit turns itself off.
• When the programmed Start and End time are earlier than the current time, the setting will not be accepted
and be cleared for redoing.
• If the Start time is earlier and the End time is later than the current time, the recording will start right after
you turn the power off.
The priority of overlapped settings
This unit records the programs according to priority if the timer programmings are overlapped. The timer
programming set previously has priority.
A Timer Recording of lower priority will be canceled, start from the middle or stop on the way.
Check the overlapped timer programmings and change the priority if necessary.
A programming set previously has priority
When the starting time is same:
A program set previously (PROG. A) has priority.
When some programming have been made at
the end time of the programming currently
being recorded:
A program set previously (PROG. B) has priority.
PROG. A
PROG. A
PROG. B
PROG. B
PROG. C
Actual
PROG. A
PROG. B
recording
The first 30 seconds (at the longest) will be cut off.
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to
be recorded.
Actual
PROG. A
PROG. B
recording
The first 30 seconds (at the longest) will be cut off.
When the recording time is entirely overlapped:
PROG.A will not be recorded.
PROG. A
PROG. A
PROG. B
PROG. B
Actual
PROG.B
PROG.A
recording
The first 30 seconds (at the longest) will be cut off.
Actual
recording
Note for DVD recording
• When the recording time of two programs
are overlapped, or the End time of a
program and the Start time of another
is the same, the first 30 seconds (at the
longest) of the subsequent program will be
cut off.
• If the cut-off portion comes up to one
minute or more, this program will be
displayed with error number E40 in the
timer programming list.
PROG. B
When the End time of the programming
currently being recorded and the Start time
of the subsequent program are same:
If PROG. A is a DVD recording program, the
beginning of the PROG. B may be cut off.
PROG. A
PROG. B
Actual
recording
PROG. A
PROG. B
The first 30 seconds (at the longest) will be cut off.
32 EN
DVR91DG_E7A01UD.indd 32
2006/02/15 17:26:18
Recording
Before you start
Settings for an external source
Connection to an external source
Video
DVD-RW
VR
DVD-RW
DVD-R
Another source
(VCR camcorder etc.)
OUTPUT
S- VIDEO
VIDEO AUDIO
L
Connections
Connect the external source properly to the unit by using input jacks either LINE2 (Front) or LINE1 (Rear).
When connecting an external equipment of monaural output to this unit, use AUDIO L jack of LINE2 (Front).
Use commercially available S-Video or Video cable and an Audio cable for this connection.
OUTPUT
AUDIO
R
R
VIDEO
S -VIDEO
L
Getting started
or
or
S-Video Video
cable cable
Audio
cable
Audio
cable
Video S-Video
cable cable
or
VIDEO
L AUDIO R
Recording
S-VIDEO
VIDEO IN
S-VIDEO
IN
L
To LINE 2 IN
Front of this unit
OPEN/CLOSE
CHANNEL
REV
FWD
STOP
PLAY
VIDEO IN
COMPONENT
VIDEO OUTPUT
S-VIDEO
VIDEO
Rear of this unit
L AUDIO R
VIDEO OUT
Y
OUT
IN
REC/OTR
S-VIDEO
AUDIO IN
POWER
IN
REC SPEED
R
To LINE 1 IN
L
OUT
L
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
PB/CB
R
ANTENNA
R
PR/CR
AUDIO IN
(L1)
AUDIO OUT
COAXIAL
Playing discs
1. Press [SETUP].
2. Using [K / L], select “Required Setting”. Press [ENTER].
3. Using [K / L], select “Select Video”. Press [ENTER].
Select Video
Video In
L2 (Front)
Video In
4. Using [K / L], select “L2 (Front)”. Press [ENTER].
Editing
L1 (Rear)
4. Using [K / L], select “L1 (Rear)”. Press [ENTER].
Select Video - L1 (Rear)
Video In
Video In
S-Video In
S-Video In
Select Video
5. Using [K / L], select the input jack type to
connect. Press [ENTER].
If you want to use S-VIDEO IN jack, select
“S-Video In”.
If you want to use VIDEO IN (Composite) jack,
select “Video In”.
Select Video
L1 (Rear)
Video In
L1 (Rear)
S-Video In
L2 (Front)
S-Video In
L2 (Front)
Video In
Español
6. Press [SETUP] to exit.
6. Press [SETUP] to exit.
EN
DVR91DG_E7A01UD.indd 33
Others
5. Using [K / L], select the input jack type to
connect. Press [ENTER].
If you want to use S-VIDEO input jack, select
“S-Video In”.
If you want to use VIDEO input (Composite) jack,
select “Video In”.
Changing the
Setup menu
Select Video - L2 (Front)
33
2006/02/15 17:26:19
Recording
Settings for an external source (cont’d)
Recording from an external source
Video
DVD-RW
VR
DVD-RW
DVD-R
Before recording from an external source, see the instructions for the connection on page 33.
1. Turn the TV and this unit on, and be sure to select the input of the
TV to which the unit is connected.
Refer to the table on page 15.
2. Press [OPEN/CLOSE A] to open the disc tray. Place the disc to
record properly.
POWER
3. Press [OPEN/CLOSE A] to close the disc tray.
4. Select the input of the unit which the external equipment is
connected. (L2 or L1)
• To use the input jacks on the back of this unit, select “L1” position by
pressing [0], [0], [1] on the remote control or the [CHANNEL L / K] .
• To use the input jacks on the front of this unit, select “L2” position by
pressing [0], [0], [2] on the remote control or the [CHANNEL L / K] .
5. Select a recording speed pressing [REC SPEED].
Refer to “Recording speed” on page 24.
7. Press “Play” on the external source to
record from.
3
Using [K / L], select “Disc
Protect OFF
ON”. Press
[ENTER].
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
SP
(2H)
LP
(4H)
SEP
(10H)
SLP
(8H)
EP
(6H)
REPEAT
B
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
PAUSE
H
REC/OTR
CHANNEL
FWD
g
SKIP
F
G
STOP
CM SKIP
REC SPEED
REV
ON
Yes
No
S-VIDEO
5 6
.@/:
STOP
PLAY
TIMER
ZOOM
PROG.
ABC
DEF
VIDEO
L AUDIO R
A
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
2
3
4
POWER
OPEN/CLOSE
GHI
1
K
{
B
L
REC SPEED
Note Bx1.3/0.8
Using [K / L], select “Yes”.
Press [ENTER].
A disc will be protected.
FWD
REC/OTR
POWER
Confirmation window will appear.
4
CH
C
1
Using [K / L], select “Disc”.
Press [ENTER].
Disc menu will appear.
3
MNO
23 4 8
VR
2
2
JKL
L
Setting a disc to protect
Press [SETUP].
1
GHI
OPEN/CLOSE
XP
(1H)
Disc Protect OFF
A
K
This operation may take a while to be completed.
To prevent accidental recording,
editing or erasing the titles, you
can protect them from the Setting
menu.
DEF
{
8. Press [STOP C] on the unit to stop recording.
DVD-RW
ABC
OPEN/CLOSE
0
This operation may take a while to be recognized.
6. Press [REC/OTR] on the unit to start
recording.
PROG.
.@/:
4
TIMER
ZOOM
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
SKIP
H
F
G
• The Disc Protect setting is
CM SKIP
STOP
REC/OTR only when
available
a disc
with VR mode is inserted.
• You can select only the
Disc Protect menu when a
protected disc is inserted.
To cancel the disc protect:
• When you insert a disc
protected with this unit,
“Disc Protect ON → OFF” will
appear instead of “OFF → ON”.
C
Disc Protect ON
OFF
Yes
No
To release the protect for the
disc, select “Disc Protect
ON → OFF” at step 3, then
select “Yes”.
34 EN
DVR91DG_E7A01UD.indd 34
2006/02/15 17:26:20
Recording
Before you start
Finalizing the discs
Video
DVD-RW
VR
DVD-RW
DVD-R
Using [K / L], select “Yes”.
Press [ENTER].
Finalizing will start.
POWER
.@/:
90%
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
Finalizing
TIMER
ZOOM
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
1
0
To cancel finalizing...
(DVD-RW only)
K
• To cancel finalizing at step 4,
press [STOP C], select “Yes” with
[{ / B], then press [ENTER].
Finalizing is canceled and the unit
will be in stop mode.
2
B
2
3
4
L
REC SPEED
Bx1.3/0.8
REV
PL AY
FWD
h
B
g
SKIP
PAUSE
H
F
G
STOP
CM SKIP
REC/OTR
4
SKIP
C
Recording
Press [SETUP].
{
Do you want to cancel ?
Yes
No
Using [K / L], select “Disc”.
Press [ENTER].
Disc menu will appear.
Finalizing
Using [K / L], select “Finalize”.
Press [ENTER].
Confirmation window will appear.
Finalize
Yes
No
5%
This operation may take a
while to be completed.
Finalizing is completed.
Changing the
Setup menu
5
Note
• Finalizing discs in Video
mode automatically creates
title menus.
• Once you have finalized a
disc recorded in Video mode,
you cannot edit or record
anything else on that disc.
Discs recorded in VR mode
can still be recorded and
edited on this recorder even
after finalized.
• When you insert a DVD-RW
disc finalized with this unit,
“Undo Finalize” will appear
instead of “Finalize”.
Editing
• If appears when pressing
[STOP C], you cannot cancel
finalizing because the finalizing
has been in certain progress.
• When selecting “No” and press
[ENTER] or [RETURN
],
finalizing will be continued.
• You cannot cancel finalizing the
DVD-R disc once it has started.
Playing discs
3
Getting started
1
4
Connections
You will need to finalize discs
recorded in Video mode to play in
other DVD players.
Finalizing may take several
minutes up to an hour. (A disc
recorded in Video mode can take
up to 15 minutes. A disc recorded
in VR mode can take up to 60
minutes.)
A shorter recording period on
the disc will require a longer time
period for finalization. Do not
unplug the power cord during
finalization.
Details are on pages 24-25.
Disc
Format
Undo Finalize
Finalizing
Others
Disc Protect OFF
ON
100%
EN
DVR91DG_E7A01UD.indd 35
Español
To release the finalizing
for the disc, select “Undo
Finalize” at step 3.
• DO NOT power off during
finalization, this will result in
malfunction.
35
2006/02/15 17:26:21
Recording
Finalizing the discs (cont’d)
Auto finalize
Video
DVD-RW
DVD-R
You can finalize discs
automatically using Auto Finalize
function. You can use this function
to finalize discs after finishing all
Timer Recordings and at the end
of the disc space.
4
POWER
Using [K / L], select “Disc Full”
or “End of Timer Rec”. Press
[ENTER].
Option window will appear.
.@/:
1
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
Auto Finalize - Disc Full
TIMER
ZOOM
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
ON
1
6
OFF
Press [SETUP].
K
{
2
B
L
REC SPEED
Using [K / L], select
“Recording”. Press [ENTER].
Recording menu will appear.
Bx1.3/0.8
REV
PL AY
h
B
SKIP
H
REC/OTR
Auto Finalize - End of Timer Rec
g
SKIP
F
G
STOP
CM SKIP
C
ON
3
PAUSE
FWD
2
3
4
5
OFF
Using [K / L], select “Auto
Finalize”. Press [ENTER].
Auto Finalize menu will appear.
Auto Finalize
Disc Full
OFF
End of Timer Rec
OFF
5
Using [K / L], select “ON”.
Press [ENTER].
Your setting will be activated.
6
Press [SETUP] to exit.
Note
• Auto Finalize does not
function for VR format discs.
36 EN
DVR91DG_E7A01UD.indd 36
2006/02/15 17:26:22
Playing discs
Before you start
Information on DVD play
Before you play DVD discs, read the following information.
Color systems
This unit is compatible to play the following discs.
To play a DVD, make sure that it meets the
requirements for Region Codes and Color Systems
as described followings. Discs that have the following
logos will play on the unit. Other Disc types are not
guaranteed to play.
DVDs are recorded in different color systems
throughout the world. The most common color
system is NTSC (which is used primarily in the
United States and Canada).
This unit uses NTSC, so DVDs you play must be
recorded in the NTSC system. You cannot play
DVDs recorded in other color system .
Disc
Logo
Connections
Playable discs
Region codes
DVD-VIDEO
DVD-RW (VIDEO/VR mode)
DVD-R (VIDEO mode)
CD-RW (CD-DA FORMAT)
CD-R (CD-DA FORMAT)
Hint for DVD playback
is a trademark of DVD Format/Logo Licensing Corporation.
The contents of DVD disc are generally divided into
titles. Titles may be further subdivided into chapters.
Start Rec.
Stop Rec.
Editing
Title 1
Stop/Start
Playing discs
The number inside the globe refers to region of the
world.
A DVD labeled for a specific region can only play on
the unit with the same region code.
Recording
CD-DA (AUDIO CD)
Getting started
This unit has been designed to play DVD discs with
Region One (1). DVDs must be labeled for ALL
regions or for Region 1 in order to play on the unit.
You cannot play DVDs that are labeled for other
regions. Look for the symbols below on your DVDs.
If these region symbols do not appear on your DVD,
you cannot play the DVD in this unit.
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
Start Rec.
Press [DISPLAY] to call up the
Display menu. This menu will
give you the information on the
playing disc. Some operations are
available while disc is playing.
4
1
0:00:00
DVD-R
Video mode
CH
5
8
2
Others
1
1
Stop Rec.
5. Each icon means:
1. Indicates a disc type and a
format mode.
: Search
Track 1 Track
NOTE: In some descriptions
on 2 Track 3 Track 4 Track 5
: Audio
this manual, only one disc type
is indicated as an example.
: Subtitle
2. Indicates a channel number.
: Angle (except VR mode)
3. Indicates a recording mode and
possible recording time left.
: Repeat
4. Indicates a title number, chapter
: Marker
number and the time lapse of
disc play.
: Noise Reduction
Changing the
Setup menu
Guide to displays
: Zoom
6
1:01
3
: Surround
6. Indicates current disc status.
EN
DVR91DG_E7A01UD.indd 37
Español
XP
37
2006/02/15 17:26:23
Playing discs
Basic playback
Playback
Video
DVD-RW
VR
DVD-RW
DVD-R
1
<VR mode>
Playlist
Press [POWER].
Turn the TV on and be sure to
select the input to which the unit is
connected.
1
2
3
POWER
1
JAN/ 1/06 1:00AM CH12 XP
4
5
6
2
Press [OPEN/CLOSE A] .
The disc tray will open.
3
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
B
disc tray
guide
4
Press [OPEN/CLOSE A] to close
the disc tray.
This operation may take a
while to be recognized.
1
2
3
5
6
JAN/ 1/06 1:00AM CH12 XP
4
3
7
REC SPEED
REV
Bx1.3/0.8
SKIP
FWD
g
B
PAUSE
H
REC/OTR
5
PL AY
h
SKIP
F
G
STOP
CM SKIP
C
6
6
7
5
8
6
Using [K / L / { / B], select a
desired title. Press [ENTER].
Option window will appear.
<Video mode>
Title List
Play
Edit
Title List
2
2
4
8
To exit the title menu, press
[STOP C] or [RETURN
].
5
Press [TOP MENU] to display
the Title menu.
You can change “Original” or
“Playlist” of VR mode using
[MENU / LIST].
<Video mode>
L
JAN/ 1/06 1:00AM CH12 XP
4
REPEAT
K
Original
1
A
CH
{
Insert your disc with its label facing up. Align the disc to the disc
tray guide.
OPEN/CLOSE
PROG.
0
5
[MENU / LIST]
TIMER
ZOOM
Note
2
3
5
6
JAN/ 1/06 1:00AM CH12 XP
4
• For DVD-R (Video mode) and
DVD-RW (Video mode) discs
which are already finalized,
a title list will be displayed
instead of thumbnails.
Title Menu
7
Using [K / L], select “Play”.
Press [ENTER].
Playback will start.
1 JAN/22/06 12:55AM CH10 XP
2 JAN/30/06 11:00PM CH8
XP
3 FEB/10/06 9:00PM CH10 LP
4 FEB/28/06 11:00AM CH6
LP
5 FEB/28/06 10:00PM CH8
EP
8
Press [STOP C] to stop playback.
To eject the disc, press [OPEN/
CLOSE A] to open the disc tray,
then remove the disc before
turning the unit off.
• You can resume play from
where you stopped playing
the disc. (Resume play)
Refer to page 41 for details
about resume play.
• Some discs may start
playback automatically.
• You can also start playback
by pressing [PLAY B] in
stead of [ENTER] at step 6.
38 EN
DVR91DG_E7A01UD.indd 38
2006/02/15 17:26:24
Playing discs
DVD-V
CD
1
2
3
1
POWER
PROG.
.@/:
ABC
DEF
1
2
3
GHI
If you are playing a DVD-Video
disc, a menu may appear.
Refer to page 40 for details about
the Disc menu.
TIMER
ZOOM
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
2
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
5
K
{
B
4
L
Press [STOP C] to stop playback.
REC SPEED
Bx1.3/0.8
Insert your disc with its label facing up. Align the disc to the disc
tray guide.
REV
PL AY
FWD
h
B
g
SKIP
H
REC/OTR
PAUSE
SKIP
F
G
STOP
CM SKIP
5
C
Getting started
Press [OPEN/CLOSE A] to open
the disc tray.
The disc tray will open.
Press [PLAY B] to start playback.
Playback will start.
Connections
Press [POWER].
Turn the TV on and be sure to
select the input to which the unit is
connected.
4
Before you start
Basic playback (cont’d)
Note
Recording
• Some discs may start
playback automatically.
Playing discs
Editing
Changing the
Setup menu
Others
Español
EN
DVR91DG_E7A01UD.indd 39
39
2006/02/15 17:26:24
Playing discs
Basic playback (cont’d)
Playing discs using the Disc menu
DVD-V
A DVD disc contains a Disc
menu that describes the contents
or allows you to customize the
playback. For example, the menu
may offer choices for subtitle
languages, special features, or
chapter selection.
Sometimes these are displayed
automatically when you start
playback, otherwise only appear
when you press [MENU / LIST].
1
Press [MENU / LIST].
The Disc menu will appear.
If the feature is not available, may appear on the TV screen.
2
Using [K / L / { / B], select an
item. Press [ENTER] to confirm.
Continue this step to set up all
the features you want or to start
playing the disc from the menu.
MENU / LIST button:
Displays a DVD Disc menu which
varies with the disc and may be
the same as the ‘Title menu.’
Cursor K / L / { / B buttons:
Moves the cursor around screen.
ENTER button:
Selects the currently highlighted
menu option.
Number buttons:
Selects a numbered menu option
(some discs only). (Press [ENTER]
after.)
3
Press [MENU / LIST] to exit the
Disc menu.
POWER
.@/:
2
Some DVDs have a Title menu,
which lists the titles available on
them. It helps you to start play at a
specific title.
1
Press [TOP MENU].
The Title menu will appear.
If the feature is not available, may appear on the TV screen.
2
Using [K / L / { / B], select a
title to play. Press [ENTER].
Play will begin at the title you
selected.
TOP MENU button:
Displays the ‘Title menu’ of a DVD
disc which varies with the disc.
Cursor K / L / { / B buttons:
Moves the cursor around screen.
ENTER button:
Selects the currently highlighted
menu option.
Number buttons:
Selects a numbered menu option
(some discs only). (Press [ENTER]
after.)
3
Press [TOP MENU] to exit the
Title menu.
Pause
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
1
2
3
2
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Note
• Menus vary among discs.
Refer to the information
accompanying the disc for
details.
Playing discs using the Title menu
DVD-V
TIMER
ZOOM
POWER
2
.@/:
Note
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
1
2
3
TIMER
ZOOM
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
2
K
{
B
L
REC
SPEED
POWER
PL AY OPEN/CLOSE
FWD
TIMER
g
REV
h
ZOOM
B
PROG.
Bx1.3/0.8
SKIP
PAUSE
A
SKIP
.@/:
H
ABC
F
DEF
G
1
3
2
CM SKIP
STOP
• [TOP REC/OTR
MENU]
will
not
always
CH
JKL
GHI
MNO
be active
with
all6 DVDs.
4
5
WXYZ
REPEAT
• MenusPQRSvaryTUVamong
discs.
7
9
8
Refer DISPLAY
to
the
information
SPACE
CLEAR
SETUP
accompanying
the disc for
0
ENTER
TOP MENU MENU/LIST RETURN
details.
C
K
Video
DVD-V
DVD-RW
DVD-R
CD
VR
DVD-RW
{
2
REC SPEED
Press [PLAY B] to resume play.
Bx1.3/0.8
1
REC/OTR
During playback, press
[PAUSE F].
Play will pause and sound will be
muted.
F
B
L
REV
PL AY
FWD
h
B
g
SKIP
PAUSE
H
F
SKIP
G
STOP
CM SKIP
2
1
C
Note
• On DVDs, set “Still Mode” to
“Field” in the Setup menu
if pictures in the pause mode
are blurred.
(Refer to page 70.)
40 EN
DVR91DG_E7A01UD.indd 40
2006/02/15 17:26:25
POWER
.@/:
Playing discs
Video
DVD-RW
DVD-R
CD
VR
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
During playback, press [STOP C].
The resume message will appear.
REPEAT
K
B
2
L
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
1
2
C
POWER
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
Getting started
To cancel the resume play and
start playing the disc from the
beginning, press [STOP C] the
second time while the play is
stopped.
Resume ON
CH
CH
REPEAT
0
Fast forward / Fast reverse
Video
DVD-RW
VR
DVD-RW
K
{
CD
DVD-R
1
REC SPEED
x40
g
REV
g
FWD
x20
g
REV
g
FWD
x5
g
REV
g
FWD
Normal
speed
playback
g
REV
g
FWD
x2
g
REV
g
FWD
x20
g
REV
g
x40
Skipping TV commercials during play
DVD-RW
VR
DVD-RW
You can skip TV commercials by pressing [CM SKIP], so that you can
enjoy the recorded programs without interrupting.
1
1
FWD
g
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
REC/OTR
C
Note
• Forward/reverse speed will
be indicated with icons as
follows.
Forward (Approx. Speed)
x2:
x20:
x40:
Reverse (Approx. Speed)
x5:
x20:
x40:
POWER
.@/:
DVD-R
B
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
Changing the
Setup menu
DVD-V
Video
PL AY
h
Editing
For Audio CDs, approximate speed is fixed at x8 with sound.
To return to the normal play, press [PLAY B].
Bx1.3/0.8
REV
Playing discs
During playback, press [FWD D] or [REV E].
Every time you press [FWD D] or [REV E], approximate speed will be
changed as follows.
Fast forward or fast reverse playback across titles (for DVD discs) or
tracks are not possible.
FWD
B
L
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
During playback, press [CM SKIP].
Normal play will start at 30 seconds ahead from the point you press
[CM SKIP].
K
{
B
L
REC SPEED
Bx1.3/0.8
REC/OTR
REV
PL AY
h
B
Others
Every time you press [CM SKIP], the searching point will be extended by
30 seconds ahead.
You can press up to 6 times (180 seconds).
FWD
g
SKIP
PAUSE
H
F
SKIP
G
STOP
CM SKIP
1
C
e.g. Press [CM SKIP] once.
(forwarding 30 seconds)
Español
CM Skip 30 sec.
B
Playback will restart automatically.
EN
DVR91DG_E7A01UD.indd 41
Recording
DVD-V
Connections
1
A
1
{
Press [PLAY B].
In a few seconds, play will resume
from the point at which it stopped
last. You can resume play at the
same point even if you turn off the
unit.
You can resume play from where
you stopped playing the disc last.
DEF
GHI
2
DVD-RW
ABC
OPEN/CLOSE
0
Resume play
DVD-V
PROG.
Before you start
Special playback
TIMER
ZOOM
41
2006/02/15 17:26:27
Playing discs
POWER
Special playback (cont’d)
.@/:
Rapid Play
DVD-V
Video
DVD-RW
VR
: Press [Bx1.3/0.8] once
during playback.
Plays back approximately
at 0.8 times of normal
playback.
B
DVD-RW
DVD-R
Rapid Play function is available
only during playback.
Available only on discs recorded
in the Dolby Digital format, Rapid
Play plays back in a slightly
faster/slower speed while keeping
the sound quality just as normal
playback.
: Press [Bx1.3/0.8] three
times to play back in
normal speed.
No effects.
B
1
During playback, press
[Bx1.3/0.8].
: Press [Bx1.3/0.8] twice
during playback.
Plays back approximately
at 1.3 times of normal
playback.
B
2
Press [PLAY B] to continue the
normal playback.
DVD-V
DVD-RW
DVD-R
1
During playback, press [PAUSE F].
Play will pause and sound will be
muted.
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
REC SPEED
1
Bx1.3/0.8
REV
PL AY
h
B
SKIP
PAUSE
H
REC/OTR
DVD-RW
DVD-RW
F
G
CM SKIP
To play step by step backward:
Press [SKIP H] repeatedly.
Every time you press the button,
the play will go backward by one
frame.
• Press and hold
[SKIP H / G] to reverse/
advance continuously.
.@/:
ABC
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
DEF
x1/4
REV
g
x1/8
g
REV
g
x1/16
7
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
K
{
B
L
REC SPEED
REV
PL AY
FWD
h
B
g
SKIP
ZOOM
TIMER
PAUSE
PROG.
F
G
ABC
STOP
DEF
CM SKIP
H
REC/OTR
.@/:
A
C
1
2
GHI
JKL
MNO
3
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
K
B
L
DVD-R
FWD
g
g
REV
OPEN/CLOSE
SKIP
3
1
2
0
FWD
g
CH
REPEAT
DISPLAY
POWER
Bx1.3/0.8
During playback, press [PAUSE F]. Then press [FWD D] or [REV E].
Every time you press [FWD D] or [REV E], approximate speed will be
changed as follows. (The sound will remain muted.)
g
2
Note
1
FWD
g
SKIP
• Audio (language) setting
cannot be changed while
using this mode.
• This feature may not work at
some point in a disc.
• Audio POWER
is PCM during
Rapid
OPEN/CLOSE
TIMER
play mode.ZOOM PROG.
A
Pause
REV
g
FWD
x1/16
To return to the normal play, press [PLAY B].
g
REV
g
FWD
x1/8
g
REV
g
x1/3
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
h
FWD
FWD
STOP
{
DVD-V
REPEAT
B
Slow forward / Slow reverse play
VR
CH
C
Press [SKIP G] repeatedly.
The play will advance one frame
(or step) at a time when you press
[SKIP G] with the sound muted.
Video
A
L
Press [PLAY B] to resume play.
2
DEF
OPEN/CLOSE
K
3
F
ABC
{
VR
DVD-RW
PROG.
0
Step by step playback
Video
TIMER
ZOOM
REC/OTR
B
FWD
g
1
C
Note
• Slow forward/slow reverse
speed will be indicated with
icons as follows.
Forward (Approx. Speed)
x1/16:
x1/8:
x1/3:
Reverse (Approx. Speed)
x1/16:
x1/8:
x1/4:
42 EN
DVR91DG_E7A01UD.indd 42
2006/02/15 17:26:28
Playing discs
Before you start
Special playback (cont’d)
Zoom
Video
DVD-RW
DVD-V
VR
DVD-RW
DVD-R
During playback, press [ZOOM].
Zoom menu will appear.
1
1
0:00:00
2
POWER
.@/:
Using [K / L], select a desired
zoom factor to zoom. Press
[ENTER].
The zoom area will be displayed.
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
Connections
1
1
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
DVD-Video
{
B
L
REC SPEED
Note Bx1.3/0.8
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
SKIP
H
F
G
C
There are four options
(x1.0, x1.2, x1.5 and x2.0), these
are displayed excluding the current
zoom rate.
3
Using [K / L / { / B], select a
desired zoom position. Press
[ENTER].
The zoom play will start.
DVD-V
Video
DVD-RW
POWER
VR
DVD-RW
<Audio CD>
1
0:00:00
CD
DVD-R
1
This feature allows you to assign a
specific point on a disc to be called
back later.
During playback, press
[DISPLAY].
The Display menu will appear.
1
0:00:00
DVD-Video
4
5
6
<DVD-Video>
1
1
0:00:00
1
2
3
4
5
6
-------------
DVD-Video
2
3
JKL
MNO
4
5
6
TUV
WXYZ
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
K
{
Using [K / L], select a desired
marker number. When it reaches the desired point, press
[ENTER].
The title (track) number and the
time will be displayed.
To return to the marker later:
Using [K / L], select the desired
marker number. Press [ENTER].
1
A
2
3
4
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Note
EN
DVR91DG_E7A01UD.indd 43
Español
• To clear a marker, select the
marker number to be cleared,
then press [CLEAR].
• All markers will be erased
when you operate these
operations listed below.
– Opening the disc tray
– Turning off the power
– Recording to a recordable
disc
– Changing the mode between
Original and Playlist (VR
mode)
• You can mark up to 6 points.
Others
Using [{ / B], select
.
Press [ENTER].
Marker Setup menu will appear.
1
DEF
GHI
PQRS
3
4
2
-------------
ABC
OPEN/CLOSE
Changing the
Setup menu
1
3
Audio CD
PROG.
Editing
1
2
.@/:
TIMER
ZOOM
Playing discs
Marker Setup
Recording
• When selecting a smaller
CM SKIP
STOP
factorREC/OTR
than the current
one,
the zoom area will not be
displayed.
• To exit the zoom menu, press
[ZOOM] again at step 1.
• To cancel the zoom function,
select “x1.0” using [K / L],
then press [ENTER].
Getting started
2
3
K
1.2
1.5
2.0
43
2006/02/15 17:26:30
Playing discs
Search
POWER
Title/Chapter search
Video
DVD-RW
DVD-V
.@/:
VR
DVD-RW
DVD-R
Using [SKIP H / G]
1
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
During playback, press [SKIP G] to skip the current title or chapter
and move to the next.
The title or chapter will move forward by one at a time.
• If there is no chapter in one title, the current title will be skipped.
K
{
B
L
REC SPEED
To go back to the beginning of the current title or chapter, press
[SKIP H].
Press it repeatedly to go to the previous title or chapter. The title or
chapter will move backward one title at a time.
Bx1.3/0.8
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
H
F
G
STOP
CM SKIP
REC/OTR
SKIP
1
C
Using [DISPLAY]
1
POWER
During playback, press [DISPLAY].
The Display menu will appear.
1
1
0:00:00
.@/:
2
DVD-Video
1
2
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
K
{
B
L
Using [{ / B], select
. Press [ENTER].
The number next to will be highlighted.
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
Title:
Using [K / L] or the Number buttons, enter a desired title number
to search. Press [ENTER].
Title search will start.
Chapter:
Press [B] to move to the number next to for chapter.
Using [K / L] or the Number buttons, enter a desired chapter number to search. Press [ENTER].
Chapter search will start.
Note
TIMER
ZOOM
01 /01
001/028
REC/OTR
PL AY
B
PAUSE
2
FWD
g
SKIP
F
G
STOP
CM SKIP
C
00:00:00/02:18:33
• In search mode display, total
numbers of each search contents
(title/chapter/time) are shown as a
denominator.
Total time
Total number
of titles
Total number
of chapters
44 EN
DVR91DG_E7A01UD.indd 44
2006/02/15 17:26:31
POWER
Playing discs
.@/:
Track search
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
Before you start
Search (cont’d)
TIMER
ZOOM
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
CD
Using [SKIP H / G]
K
{
REC SPEED
During playback, press [SKIP G] to skip the current track and
move to the next.
The track will move forward one at a time.
To go back to the beginning of the current track, press [SKIP H].
Press it repeatedly to go to the previous track. The track will move
backward one at a time.
Bx1.3/0.8
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
H
F
G
STOP
CM SKIP
REC/OTR
SKIP
1
C
Getting started
Using [DISPLAY]
POWER
1
1
0:00:00
.@/:
Audio CD
1
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
Recording
During playback, press [DISPLAY].
The Display menu will appear.
<Audio CD>
TIMER
ZOOM
REPEAT
0
K
Using [{ / B], select
. Press [ENTER].
The number next to will be highlighted.
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
Note
3
2
3
B
L
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Using [K / L] or the Number buttons, enter a desired track number
to search. Press [ENTER].
Track search will start.
Time search
POWER
Video
DVD-RW
DVD-R
CD
DVD-RW
1
During playback, press
[DISPLAY].
The Display menu will appear.
<DVD-Video>
1
1
0:00:00
DVD-Video
2
Using [{ / B], select
.
Press [ENTER].
The number next to will be
highlighted.
To move to the number next to ,
press [B].
When time search is not available,
and time count are not displayed.
.@/:
1
1
0:00:00
Audio CD
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
K
2
3
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Note
EN
Español
• Time search function is
available only in the same
track or title.
DVR91DG_E7A01UD.indd 45
Others
<Audio CD>
PROG.
{
3
Using [K / L] or the Number
buttons, enter a desired time to
search. Press [ENTER].
Time search will start.
TIMER
ZOOM
Changing the
Setup menu
DVD-V
VR
Editing
• During CD playback you can
enter a track number directly
using the Number buttons
for track search without
displaying the menu.
Playing discs
2
{
Connections
1
B
L
45
2006/02/15 17:26:32
Playing discs
POWER
Repeat/Random/Program playback
Repeat playback
DVD-V
Video
DVD-RW
VR
DVD-RW
CD
DVD-R
1
During playback, press
[REPEAT].
Repeat menu will appear.
<DVD-Video>
1
1
0:00:00
DVD-Video
OFF
Title
Chapter
A-B
<Audio CD>
1
0:00:00
Audio CD
OFF
Track
All
A-B
2
Using [K / L], select a desired
option to repeat. Press [ENTER].
The selected repeat play will start.
Title:
The current title will be played
repeatedly. (DVD only)
ABC
DEF
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
REPEAT
1
B
2
L
REC SPEED
Bx1.3/0.8
REV
PL AY
h
B
SKIP
PAUSE
H
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Note
• The A-B Repeat playback can
only be set with in the current
title (for DVDs), or current
track (for Audio CDs).
• To cancel the repeat
playback, select “OFF” at
step 2. The repeat setting will
also be canceled when you
stop playback.
.@/:
3
Using [K / L], select “Random
Play”. Press [ENTER].
Random play will start.
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
1
K
{
B
L
Press [SETUP].
REC SPEED
REV
Bx1.3/0.8
SKIP
h
2
Using [K / L], select “CD
Playback Mode”. Press [ENTER].
CD Playback Mode menu will
appear.
CH
K
Random play
With this function, you can play a
disc randomly instead of playing in
the original order.
A
1
POWER
CD
OPEN/CLOSE
GHI
{
All:
The current disc will be played
repeatedly. (CD, DVD-RW (VR
mode) only)
Track:
The current track will be played
repeatedly. (CD only)
PROG.
0
Chapter:
The current chapter will be played
repeatedly. (DVD only)
A-B:
The A-B point will be played
repeatedly.
When pressing [ENTER] while A-B
is highlighted, A-B repeat is set.
Press [ENTER] again to decide
the starting point (A).
Press [ENTER] after setting point
A to select the ending point (B).
.@/:
TIMER
ZOOM
H
REC/OTR
PL AY
B
PAUSE
FWD
1
2
3
g
SKIP
F
G
STOP
CM SKIP
C
Note
• To cancel random play,
press [STOP C] twice during
random play. “Playmode OFF”
appears on the screen.
46 EN
DVR91DG_E7A01UD.indd 46
2006/02/15 17:26:33
Playing discs
TIMER
Repeat/Random/Program playback (cont’d)
.@/:
Program play
CD
1
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
4
PROG.
TUV
WXYZ
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
09
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total
REC SPEED
REV
Bx1.3/0.8
SKIP
H
5
Press [PLAY B] to start
program playback.
Program playback will start.
Note
• To erase tracks you selected,
press [CLEAR].
• You can make program
settings up to 50.
• To cancel program play,
press [STOP C] twice during
program play. “Play mode
OFF” appears on the screen.
• You may also select a desired
track using the Number
buttons
POWER at step 4.OPEN/CLOSE
TIMER
0:00:00
DVD-Video
1
2
3
JKL
MNO
4
5
6
TUV
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
{
2
3
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
DVD-Video
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
OFF
1.English
2.Japanese
Note
• Some discs will only allow you
to change the subtitle from
the Disc menu. Press
[TOP MENU] or [MENU / LIST]
to display the Disc menu.
• If a 4-digit language code
appears in the subtitle
menu at step 2, refer to the
“Language code” on page 75.
EN
DVR91DG_E7A01UD.indd 47
Español
Using [K / L], select a desired
subtitle language. Press
[ENTER].
Subtitle will be displayed in the
selected language.
When selecting “OFF”, subtitle will
disappear.
CH
K
Using [{ / B], select
.
Press [ENTER].
Subtitle menu will appear.
3
WXYZ
A
Others
1
DEF
Changing the
Setup menu
1
PROG.
ABC
2
1
During playback, press
[DISPLAY].
The Display menu will appear.
ZOOM
GHI
PQRS
1
0:00:00
G
CM SKIP
Editing
Switching subtitles
1
F
STOP
5
You can select the format of audio and video as you prefer depending on
the contents of the disc you are playing.
1
g
SKIP
C
Selecting the format of audio and video
Many DVD-Video discs have
subtitles in one or more languages
– the case usually tells you which
subtitle languages are available.
You can switch subtitle languages
anytime during playback.
PAUSE
REC/OTR
.@/:
VR
B
h
FWD
0:06:11
0:00:00
DVD-RW
PL AY
Playing discs
--
--
DVD-V
B
L
Program Play
--
2
3
4
K
Recording
Using [K / L], select “Program
Play”. Press [ENTER].
Program Play list will appear.
1
Getting started
3
REPEAT
7
{
Using [K / L], select “CD
Playback Mode”. Press [ENTER].
CD Playback Mode menu will
appear.
CH
DISPLAY
Program Play
2
A
0
Using [K / L], select a desired
track. Press [ENTER] or [B].
A cursor will move to next.
Press [SETUP].
OPEN/CLOSE
Connections
You can program the disc to play
in your desired order.
ZOOM
Before you start
POWER
47
2006/02/15 17:26:34
Playing discs
Selecting the format of audio and video (cont’d)
Switching audio soundtrack
DVD-V
VR
DVD-RW
CD
When playing a DVD-Video
disc recorded with two or more
soundtracks (these are often in
different languages), you can
switch them during playback.
On DVD-RW discs recorded in VR
mode, you can switch to main (L),
sub audio (R) or a mix of both (L/R).
When playing Audio CDs files you
can switch between stereo, just
the left channel or just the right
channel.
1
<Audio CD>
1
1
1
0:00:00
.@/:
3
Using [K / L], select a desired
audio soundtrack or audio channel. Press [ENTER].
<DVD-Video>
Audio soundtrack will switch.
1
0:00:00
1
0:00:00
DEF
4
Using [K / L], select a desired
DVD-RW
1.Dolby Digital Dual L/R
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
DVD-RW
DVD-RW
B
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
PAUSE
REC/OTR
1
1
DVD-Video
1
OFF
Type 1
Type 2
0:00:00
G
CM SKIP
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
JKL
MNO
4
5
6
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
2
K
{
<DVD-RW VR mode>
1
1
0:00:00
B
L
REC SPEED
DVD-RW
VR Playlist
The Display menu will appear.
1
F
STOP
GHI
PQRS
0:00:00
You can enjoy stereophonic virtual
space through your exciting 2
channel stereo system.
1
During playback, press [DISPLAY].
g
SKIP
2
3
4
Note
.@/:
CD
DVD-R
FWD
• Some discs will only allow
you to change the soundtrack
from the Disc menu. Press
[TOP MENU] or
[MENU / LIST] to display the
Disc menu.
• On DVD-RW discs recorded
in VR mode that may have
both a main and a sub audio
channel, you can switch to
main (L), sub audio (R) or a
mix of both (L/R).
• This unit CANNOT record
in both stereo and SAP
(Secondary Audio Program)
at the same time.
<DVD-Video>
1
REPEAT
L
Switching virtual surround system
DVD-V
CH
0
POWER
VR
A
C
VR Playlist
Video
OPEN/CLOSE
GHI
1. L/R
2. L
3. R
<DVD-RW VR mode>
1
ABC
H
audio channel. Press [ENTER].
Audio channel will switch.
1.Dolby Digital 5.1ch English
2.Dolby Digital 2ch Japanese
PROG.
K
VR Playlist
<Audio CD>
Audio channel will switch.
DVD-Video
TIMER
ZOOM
{
DVD-RW
Audio channel menu will appear.
Follow step 4.
.
1
<DVD-RW VR mode>
During playback, press
[DISPLAY].
The Display menu will appear.
Using [{ / B], select
Press [ENTER].
Audio menu will appear.
<DVD-Video>
POWER
Audio CD
1. L/R
2. L
3. R
1
2
0:00:00
Bx1.3/0.8
OFF
Type 1
Type 2
REV
PL AY
h
B
SKIP
H
REC/OTR
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
DVD-Video
<Audio CD files>
2
Using [{ / B], select
.
Press [ENTER].
Virtual Surround menu will appear.
1
1
0:00:00
OFF
Type 1
Type 2
Audio-CD
Note
• Select Virtual Surround OFF
in a case sound is distorted.
• The setting will be kept OFF
when the unit is turned off.
48 EN
DVR91DG_E7A01UD.indd 48
2006/02/15 17:26:36
POWER
.@/:
Playing discs
TIMER
ZOOM
PROG.
ABC
DEF
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
Selecting the format of audio and video (cont’d)
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
3
Using [K / L], select “OFF”,
“Type 1” or “Type 2”.
Press [ENTER].
• OFF: no effect
• Type 1: Natural effect
• Type 2: Emphasized effect
3
K
{
B
L
REV
Bx1.3/0.8
SKIP
PL AY
B
h
Switching camera angles
PAUSE
H
REC/OTR
FWD
g
Connections
REC SPEED
SKIP
F
G
STOP
CM SKIP
C
DVD-V
Using [{ / B], select
.
Press [ENTER].
Angle will switch each time you
press [ENTER].
.@/:
1
2
3
MNO
4
5
6
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
2
K
{
B
L
DVD-Video
Bx1.3/0.8
REV
PL AY
h
B
SKIP
PAUSE
H
REC/OTR
Recording
0:00:00
DEF
JKL
REC SPEED
1
ABC
1
During playback, press
[DISPLAY].
The Display menu will appear.
1
PROG.
GHI
PQRS
1
TIMER
ZOOM
Getting started
Some DVD-Video discs feature
scenes shot from two or more
angles, check the case for details:
it should be marked with Angle
icon if it contains multi-angle
scenes.
2
POWER
Before you start
1
GHI
OPEN/CLOSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Angle icon appears when a
switching camera angle is available.
Playing discs
Note
Angle icon does not appear on
the screen in a case you have
selected Angle as “OFF” in the
Display setting.
Refer to pages 67-68.
Reducing block noise
Video
DVD-RW
VR
DVD-RW
Noise Reduction menu will appear.
1
1
0:00:00
POWER
DVD-Video
DVD-R
.@/:
OFF
Type 1
Type 2
During playback, press
[DISPLAY].
The Display menu will appear.
1
1
0:00:00
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
1
PROG.
TUV
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
2
3
DVD-Video
3
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
.
REC/OTR
B
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Español
Using [{ / B], select
Press [ENTER].
This function reduces noise in the
playback picture. When playing
back discs recorded in long time
mode such as SLP or SEP mode,
select “Type 1” or “Type 2”.
(“Type 2” is more effective.)
When playing back discs with a
few noises such as DVD-Video
discs, select “OFF”.
PL AY
PAUSE
Others
Using [K / L], select a desired
option. Press [ENTER].
Your setting will be activated.
2
WXYZ
OPEN/CLOSE
EN
DVR91DG_E7A01UD.indd 49
Changing the
Setup menu
1
TIMER
ZOOM
Editing
DVD-V
49
2006/02/15 17:26:37
Editing
Information on disc editing
Guide to a title list
Editing discs in Video mode
Title list allows you to check the titles recorded on
the disc easily. You can choose a title to play from
this screen and easily edit the titles as you prefer.
You can edit discs in Video mode for the following
items. Be sure that once you edit titles, they will not
remain as original.
• Deleting titles (Refer to page 51)
• Putting names on titles (Refer to page 52)
• Setting or clearing chapter markers (Refer to page
53)
Press [TOP MENU].
Original
1
2
Note
3
JAN/ 1/06 1:00AM CH12 XP
4
3 1
5
6
2
3
• Once a disc is finalized, editing the disc or
recording to the disc will not be available. (Except
DVD-RW discs in VR mode.)
• A Playlist is not available with the DVD-R discs
and DVD-RW discs in Video mode.
Editing discs in VR mode
Original
6
For discs in VR mode, you can edit from Original
menu or Playlist menu, which is created from the
original.
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Protect
Editing Original titles
JAN/ 1/06 1:00AM CH12 XP
0:00:59
8 7
6
5
4
1. Titles recorded on the disc can be selected to edit
or play by pressing [ENTER] with the cursor on the
title.
2. The protect icon, which appears when the title has
been protected. (Original titles only)
3. The arrow icon, which means the Title list includes
a next or a previous page. Press [{ / B] by
following direction of the icon.
4. The menus in here for editing titles as you prefer.
The available menus depend on the disc type and
the format type. An item which is not available is
grayed.
5. The details of the title, which can be changed to
the title name you will edit.
6. Time status bar of the title.
Time status will be held even after exiting the edit
mode, and you can resume playback from that
point.
7. The selected title thumbnail from the title list.
8. Playback status of the current disc.
The following items can be used to edit the Original
titles.
• Deleting titles (Refer to page 54)
• Setting titles to protect (Refer to page 55)
• Releasing titles from protecting (Refer to page 56)
Editing Playlists
You can create a Playlist from Original titles, so that
you can edit as you prefer without losing Original
titles.
The following items you can edit with a Playlist.
• Deleting titles (Refer to page 57)
• Dividing a title (Refer to page 58)
• Combining titles (Refer to page 59)
• Adding titles to a Playlist (Refer to page 60)
• Deleting a Playlist (Refer to page 60)
Editing Original titles / Playlists
The following items can be used to edit both the
Original titles and the Playlists.
• Deleting parts of titles (Refer to page 61)
• Putting names on titles (Refer to page 62)
• Setting or clearing chapter markers (Refer to page
63)
• Setting pictures for thumbnails (Refer to page 64)
Note
• Original titles once edited will not remain as
recorded originally. When you want to leave the
original as it is, edit the Playlist as you prefer.
Once all editings are made, press [RETURN
] in several times to exit the editing mode. “Writing to Disc”
appears momentarily. This is true also when opening the disc tray, pressing [POWER] to turn the unit off.
50 EN
DVR91DG_E7A01UD.indd 50
2006/02/15 17:26:37
Editing
Before you start
Editing discs in Video mode
Deleting titles
DVD-R
Video
DVD-RW
POWER
.@/:
4
Using [K / L], select “Title
Delete”. Press [ENTER].
Confirmation window will appear.
1
1
PROG.
ABC
DEF
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
1
{
REC SPEED
REV
Bx1.3/0.8
SKIP
H
5
6
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
5
JAN/ 1/06 1:00AM CH12 XP
Playing discs
2
Using [K / L], select “Yes”.
Press [ENTER].
After that, “Are you sure?” will
appear, so that select “Yes” with
[K / L] and then press [ENTER].
Title List - Title Delete
Using [K / L / { / B], select the
desired title. Press [ENTER].
Option window will appear.
1
Recording
6
0:00:59
4
2
3
4
5
B
L
JAN/ 1/06 1:00AM CH12 XP
3
REPEAT
K
Yes
h
2
CH
0
Press [TOP MENU].
Title List will appear.
1
A
GHI
No
Title List
OPEN/CLOSE
Getting started
Title List - Title Delete
TIMER
ZOOM
Connections
You can delete titles which you do
not need anymore.
Be advised that the titles once
deleted cannot be brought back to
the disc.
When the last title in the title list on
DVD-RW disc is deleted, the disc
space to record will be increased.
For DVD-R disc, the disc space to
record will not be changed.
You cannot select “Chapter Mark”
when a DVD-R disc is inserted into
the unit.
“Chapter Mark” does not work on
the title less than 5 minutes.
Are you sure?
Yes
No
Title List
3
JAN/ 1/06 1:00AM CH12 XP
Editing
2
Play
Edit
Wait for a moment.
JAN/ 1/06 1:00AM CH12 XP
4
5
6
Title will be deleted.
6
Using [K / L], select “Edit”.
Press [ENTER].
Edit menu will appear.
Title List
1
Title List
2
3
Title Delete
Edit Title Name
Chapter Mark
Others
1
Changing the
Setup menu
3
Press [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
JAN/ 1/06 1:00AM CH12 XP
4
5
JAN/ 1/06 1:00AM CH12 XP
0:00:59
Español
EN
DVR91DG_E7A01UD.indd 51
51
2006/02/15 17:26:39
Editing
Editing discs in Video mode (cont’d)
Putting names on titles
DVD-R
3
Video
DVD-RW
You can put title names on the
titles and change the names from
this menu.
The names you put on the titles
will be displayed on a Title List.
POWER
Using [K / L], select “Yes”.
Press [ENTER].
The name you entered will be
activated for the title.
.@/:
2
1
Title List - Edit Title Name
1
A B C
a b c
1 2 3
@ !
?
JAN/ 1/06 1:00AM CH12 XP
0:00:59
ABC
DEF
OPEN/CLOSE
A
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
Yes
No
Follow steps 1 to 3 on page 51 to
display the Edit menu.
Using [K / L], select “Edit Title
Name”. Press [ENTER].
A window for entering a title name
will appear.
PROG.
GHI
Title List - Edit Title Name
1
TIMER
ZOOM
1
2
3
K
{
B
L
MY FAVORITE
REC SPEED
0:00:59
Bx1.3/0.8
REV
PL AY
h
B
SKIP
H
4
Press [RETURN ] and then
[RETURN ] or [STOP C] to
exit.
Data will be written onto the disc
momentarily.
REC/OTR
4
FWD
g
PAUSE
SKIP
F
G
STOP
CM SKIP
C
This operation may take a
while to be completed.
[ Guide to edit title name ]
2
To enter a title name, follow
the steps for “Guide to edit title
name” on this page.
character set
[Step1]: Select a desired character set using [K/L], then
press [ENTER].
[Step2]: Follow the list below, press the Number buttons
repeatedly until the desired letter appears.
Select
Title List - Edit Title Name
1
A B C
a b c
1 2 3
@ !
Press
0
ABC
abc
123
@!?
<space>
<space>
0
<space>
?
1
(*1)
(*1)
1
M
When you finish entering a title
name, press [ENTER].
Confirmation window will appear.
e.g. character set :
ABC
press 2
A B C A...
! ”# $ % & ’( )
* + , - . / : ; < = > Note:
?@[]^_{|}
Undefined letters in a
0:00:59
area for entering title names
ABC
abc
123
@!?
2
ABC
abc
2
(*2)
3
DEF
def
3
(*2)
4
GHI
ghi
4
(*2)
5
6
JKL
jkl
5
(*2)
MNO
mno
6
(*2)
7
8
PQRS
pqrs
7
(*2)
TUV
tuv
8
(*2)
9
WXYZ
wxyz
9
(*2)
title name are shown
by “*”. If you delete
them, adjoining letters
letters may change to
“*” or other.
*1 Press 1 , character set will be changed to the “ @!? ” mode automatically.
*2 Press 2 to 9 , character set will be changed to the previous input mode
automatically.
• To delete letters, press [CLEAR] repeatedly. Holding [CLEAR] to delete
all letters.
• Press [s / B] to move the cursor to the left or right.
• You can enter up to 30 letters.
52 EN
DVR91DG_E7A01UD.indd 52
2006/02/15 17:26:40
Editing
Before you start
Editing discs in Video mode (cont’d)
Setting or clearing chapter markers
3
Video
DVD-RW
Follow steps 1 to 3 on page 51 to
display the Edit menu.
Using [K / L], select “Chapter
Mark”. Press [ENTER].
Option window will appear.
Title List - Chapter Mark
OFF
5 minutes
.@/:
This operation may take a
while to be completed.
4
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
After this operation is completed, press [RETURN ] and
then [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
1
2
3
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
4
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Recording
1
POWER
Getting started
1
Using [K / L], select “Yes”.
Press [ENTER].
The marker will be added or deleting.
Connections
You can put chapter markers
in each title. Once a chapter is
marked, you can use it for the
chapter search feature.
You can set chapter markers at
a specified time you selected for
titles with more than 5 minutes.
10 minutes
15 minutes
30 minutes
60 minutes
JAN/ 1/06 1:00AM CH12 XP
0:00:59
Playing discs
2
Using [K / L], select a desired
time period. Press [ENTER].
Confirmation window will appear.
Title List - Chapter Mark - 5 minutes
Yes
Editing
1
No
JAN/ 1/06 1:00AM CH12 XP
0:00:59
Changing the
Setup menu
DVR91DG_E7A01UD.indd 53
Español
EN
Others
Note
• You cannot select a chapter
mark interval that exceeds
the length of a title.
• The interval of chapter marks
may be slightly longer or
shorter than the one specified at step 2.
53
2006/02/15 17:26:40
Editing
Editing discs in VR mode (Original)
Deleting titles
VR
DVD-RW
When a title is deleted from an
Original list in VR mode, the disc
space to record will be increased.
Be advised that the titles once
deleted cannot be brought back to
the disc.
4
Using [K / L], select “Title
Delete”. Press [ENTER].
Confirmation window will appear.
POWER
.@/:
Original - Title Delete
1
Yes
No
1
1
Press [TOP MENU], and then
press [MENU / LIST] to change
“Playlist” to “Original”.
Original list will appear.
Using [K / L / { / B], select the
desired title. Press [ENTER].
Option window will appear.
Original
2
Play
Edit
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
K
{
0:00:59
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Using [K / L], select “Yes”.
Press [ENTER].
After that, “Are you sure?” will
appear, so that select “Yes” with
[K / L] and then press [ENTER].
H
6
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
2
3
4
5
Original - Title Delete
3
1
Are you sure?
Yes
JAN/ 1/06 1:00AM CH12 XP
4
PROG.
JAN/ 1/06 1:00AM CH12 XP
5
2
TIMER
ZOOM
5
No
6
JAN/ 1/06 1:00AM CH12 XP
Wait for a moment.
3
Using [K / L], select “Edit”.
Press [ENTER].
Original menu will appear.
Original
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Protect
JAN/ 1/06 1:00AM CH12 XP
0:00:59
Title will be deleted.
This operation may take a
while to be completed.
6
After this operation is completed, press [RETURN ] or
[STOP C] to exit.
Data will be written onto the disc
momentarily.
Note
• Original titles once edited
will not remain as recorded
originally. When you want to
leave the original as it is, edit
the Playlist as you prefer.
54 EN
DVR91DG_E7A01UD.indd 54
2006/02/15 17:26:41
Editing
Before you start
Editing discs in VR mode (Original) (cont’d)
Setting titles to protect
VR
DVD-RW
1
Original - Protect
1
OFF
ON
POWER
After this operation is completed, press [RETURN ] and
then [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
To protect a whole disc
(DVD-RW VR mode Only):
Select “Disc Protect OFF → ON”
from the Disc menu, then select
“Yes”. Refer to “Setting a disc to
protect” on page 34.
1
2
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
B
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Recording
3
REC/OTR
PL AY
PAUSE
JAN/ 1/06 1:00AM CH12 XP
0:00:59
2
Playing discs
Confirm the indication
“OFF
ON”. Press [ENTER].
Original - Protect
1
OFF
Getting started
Follow steps 1 to 3 on page 54 to
display the Original menu.
Using [K / L]], select “Protect”.
Press [ENTER].
Option window will appear.
3
Connections
To prevent accidental editing, or
erasing the titles, you can protect
them from the Original menu.
ON
JAN/ 1/06 1:00AM CH12 XP
Editing
Wait for a moment.
This operation may take a
while to be completed.
Changing the
Setup menu
The protect icon will appear on the
title in the Original list.
Others
Español
EN
DVR91DG_E7A01UD.indd 55
55
2006/02/15 17:26:42
Editing
Editing discs in VR mode (Original) (cont’d)
Releasing titles from protecting
VR
DVD-RW
You are allowed to release the
titles protecting feature once
protected.
1
Follow steps 1 to 3 on page 54 to
display the Original menu.
Using [K / L], select “Protect”.
Press [ENTER].
Option window will appear.
3
POWER
After this operation is completed, press [RETURN ] and
then [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
K
{
B
L
Original - Protect
1
ON
REC SPEED
REV
Bx1.3/0.8
SKIP
h
OFF
H
3
REC/OTR
PL AY
B
PAUSE
FWD
g
1
2
SKIP
F
G
STOP
CM SKIP
C
JAN/ 1/06 1:00AM CH12 XP
0:00:59
2
Confirm the indication
“ON
OFF”. Press [ENTER].
Original - Protect
1
ON
OFF
JAN/ 1/06 1:00AM CH12 XP
Wait for a moment.
This operation may take a
while to be completed.
The protect icon will disappear
from the title in the Original list.
56 EN
DVR91DG_E7A01UD.indd 56
2006/02/15 17:26:42
Editing
Before you start
Editing discs in VR mode (Playlist)
Deleting titles
VR
DVD-RW
4
POWER
Using [K / L], select “Title
Delete”. Press [ENTER].
Confirmation window will appear.
.@/:
Playlist - Title Delete
1
1
Yes
No
2
Playlist
2
Play
Edit
3
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
2
3
4
5
K
JAN/ 1/06 1:00AM CH12 XP
{
B
0:00:59
L
5
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
Using [K / L], select “Yes”.
Press [ENTER].
After that, “Are you sure?” will
appear, so that select “Yes” with
[K / L] and then press [ENTER].
6
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Recording
Using [K / L / { / B], select the
desired title. Press [ENTER].
Option window will appear.
PROG.
Playlist - Title Delete
JAN/ 1/06 1:00AM CH12 XP
4
5
1
6
Are you sure?
Yes
Playing discs
No
3
JAN/ 1/06 1:00AM CH12 XP
Wait for a moment.
Using [K / L], select “Edit”.
Press [ENTER].
Playlist menu will appear.
Title will be deleted.
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Title Combining
JAN/ 1/06 1:00AM CH12 XP
0:00:59
6
After this operation is completed, press [RETURN ] or
[STOP C] to exit.
Data will be written onto the disc
momentarily.
Changing the
Setup menu
Title Dividing
Editing
This operation may take a
while to be completed.
Playlist
1
Getting started
1
Press [TOP MENU] , and then
press [MENU / LIST] to change
“Original” to “Playlist”.
Playlist will appear.
TIMER
ZOOM
Connections
In VR mode, even when a title is
deleted from a Playlist, the original
title will remain in an Original list.
The disc space to record will not
be increased.
Others
Español
EN
DVR91DG_E7A01UD.indd 57
57
2006/02/15 17:26:43
Editing
Editing discs in VR mode (Playlist) (cont’d)
Dividing a title
VR
DVD-RW
You can divide a title into two new
titles.
1
Follow steps 1 to 3 on page 57 to
display the Playlist menu.
Using [K / L], select “Title
Dividing”. Use [SKIP H / G],
[REV E], [FWD D],
[PLAY B] and [PAUSE F] to
decide the point at which you
will divide the title.
Press [ENTER].
Confirmation window will appear.
POWER
After this operation is completed, press [RETURN ] or
[STOP C] to exit.
Data will be written onto the disc
momentarily.
.@/:
Yes
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
3
Playlist - Title Dividing
1
3
REC/OTR
PL AY
B
PAUSE
FWD
1
2
g
SKIP
F
G
STOP
CM SKIP
C
No
F
JAN/ 1/06 1:00AM CH12 XP
0:00:59
2
Using [K / L], select “Yes”.
Press [ENTER].
The title will be divided into two
new titles.
Both title names are identical, and
index pictures are reset to first
scene at this point.
Playlist - Title Dividing
1
Yes
No
JAN/ 1/06 1:00AM CH12 XP
Wait for a moment.
This operation may take a
while to be completed.
Note
• You cannot divide a title of
the disc on which the number
of recording title comes up to
the maximum (99), and the
number of recording chapter
comes up to the maximum
(999).
58 EN
DVR91DG_E7A01UD.indd 58
2006/02/15 17:26:44
Editing
Before you start
Editing discs in VR mode (Playlist) (cont’d)
Combining titles
VR
DVD-RW
1
1
Yes
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
3
1 + 2
No
1
2
3
K
{
B
L
Wait for a moment.
This operation may take a
while to be completed.
3
1 +
2
TIMER
ZOOM
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
4
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Recording
2
.@/:
Playlist - Title Combining
Playlist - Title Combining
1
POWER
Using [s / B], select “Yes”.
Press [ENTER].
Two titles will combine into a
single title.
4
JAN/ 1/06 1:00AM CH12 XP
Playing discs
After this operation is completed, press [RETURN ] or
[STOP C] to exit.
Data will be written onto the disc
momentarily.
2
Getting started
Follow steps 1 to 3 on page 57 to
display the Playlist menu.
Using [K / L], select “Title
Combining”. Press [ENTER].
Title Combining setting window will
appear.
Selected title grays out, and the
frame of the next title becomes
yellow.
3
Connections
You can combine two titles into a
single title.
Using [K / L / s / B], select
another title to combine. Press
[ENTER].
Confirmation window will appear.
Playlist - Title Combining
2
3
Editing
1
1 + 2
Yes
No
Changing the
Setup menu
Note
DVR91DG_E7A01UD.indd 59
Español
EN
Others
• You cannot combine the
same titles into a single title.
• If one of two titles in the
original is deleted, the
combined new title will be
deleted automatically.
• Selection order for the
combining is affected in the
combined new title.
59
2006/02/15 17:26:44
Editing
Editing discs in VR mode (Playlist) (cont’d)
Adding titles to a Playlist
VR
DVD-RW
You can add or delete a title in the
Playlist as you prefer.
You can add titles to a Playlist up to 99.
The added title will appear as the
final title.
.@/:
1
Follow step 1 on page 57 to display
the Playlist.
Next to the final title, “Add New Title”
“Delete Playlist” menu is shown.
1
2
3
2
3
JAN/ 1/06 1:00AM CH12 XP
4
5
Using [K / L / s / B], select “Add
New Title”. Press [ENTER].
2
Using [K / L / s / B], select a
desired title. Press [ENTER].
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
1
2
Wait for a moment.
K
This operation may take a
while to be completed.
{
After this operation is completed,
press [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
To delete a title from Playlist, refer
to “Deleting titles” on page 57.
To delete a Playlist, refer to
“Deleting a Playlist” on this page.
B
L
REC SPEED
3
Add New
Title
Delete
Playlist
TIMER
ZOOM
Playlist - Add New Title
1
Playlist - Add New Title
POWER
Bx1.3/0.8
REV
PL AY
h
B
SKIP
PAUSE
H
3
REC/OTR
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Note
• When a Playlist contains 99
titles or more, or 999 chapters
or more, “Add New Title”
cannot be selected.
Deleting a Playlist
Final confirmation window will appear.
VR
DVD-RW
Playlist
A Playlist can be deleted if no
longer needed.
POWER
1
1
2
.@/:
Follow step 1 on page 57 to display
the Playlist.
Next to the final title, “Add New Title”
“Delete Playlist” menu is shown.
Using [K / L / s / B], select
“Delete Playlist”. Press [ENTER].
Confirmation window will appear.
Playlist
1
2
Are you sure?
4
ABC
DEF
1
2
3
GHI
JKL
MNO
Add New
Title
Delete
Playlist
4
5
6
PQRS
Wait for a moment.
TUV
Using [s / B], select “Yes”.
Press [ENTER].
A Playlist will be erased.
4
5
Add New
Title
Delete
Playlist
Add New
Title
Delete
Playlist
CH
REPEAT
7
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
1
2
3
K
{
B
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Playlist
No
A
DISPLAY
H
Yes
WXYZ
OPEN/CLOSE
0
3
3
PROG.
No
Yes
5
TIMER
ZOOM
3
4
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
2
Using [s / B], select “Yes”.
Press [ENTER].
This operation may take a
while to be completed.
4
After this operation is completed,
press [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
Note
• Deleting a Playlist will not
increase the available
recording time on disc.
60 EN
DVR91DG_E7A01UD.indd 60
2006/02/15 17:26:45
Editing
Deleting parts of titles
VR
DVD-RW
1
2
Using [K / L / { / B], select the
desired title. Press [ENTER].
Option window will appear.
<Playlist>
Playlist
Start point End point
3
8
After this operation is completed, press [RETURN ] and
then [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
POWER
.@/:
1
6
ABC
DEF
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Edited
Using [K / L], select “Delete”.
Press [ENTER].
Confirmation window will appear.
<Playlist>
8
5
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Playlist - Scene Delete
1
Playlist
Yes
No
Title Delete
Editing
1
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
JAN/ 1/06 1:00AM CH12 XP
Title Dividing
0:00:59
Title Combining
JAN/ 1/06 1:00AM CH12 XP
4
Using [K / L], select “Scene
Delete”. Press [ENTER].
Option window will appear.
<Playlist>
Playlist - Scene Delete
7
Changing the
Setup menu
0:00:59
Using [K / L], select “Yes”.
Press [ENTER].
After that, “Are you sure?” will
appear, so that select “Yes” with
[K / L] and then press [ENTER].
<Playlist>
Playlist - Scene Delete
Start
1
End
No
Delete
JAN/ 1/06 1:00AM CH12 XP
Are you sure?
Yes
Preview
JAN/ 1/06 1:00AM CH12 XP
0:00:59
Wait for a moment.
EN
Español
Part of a title will be deleted.
This operation may take a
while to be completed.
Note
• Original titles once edited
will not remain as recorded
originally. When you want to
leave the original as it is, edit
the Playlist as you prefer.
• You cannot select “Scene
Delete” when the number of
chapter markers is more than
900.
Others
1
DVR91DG_E7A01UD.indd 61
Playing discs
2
3
4
5
6
7
B
L
6
Using [K / L], select “Edit”.
Press [ENTER].
Original or Playlist menu will appear.
<Playlist>
A
1
H
3
OPEN/CLOSE
GHI
{
JAN/ 1/06 1:00AM CH12 XP
5
PROG.
K
Before
editing
4
TIMER
ZOOM
Recording
2
Play
Edit
Use [SKIP H / G], [REV E],
[FWD D], [PLAY B] and
[PAUSE F] to decide the start
point, then press [ENTER].
Then use [SKIP H / G],
[REV E], [FWD D], [PLAY B]
and [PAUSE F] again to move
to the end point, and press
[ENTER].
A cursor will move to “Preview”.
The bar at the bottom of the
screen indicates the total and the
elapsed time of the title, and the
area selected for deletion will be
indicated in red.
Press [ENTER] again to start
the preview.
You can check the result of
deletion by “Preview”.
Getting started
Press [TOP MENU], and then
press [MENU / LIST] to select
“Original” or “Playlist”.
5
Connections
You can delete a specific part of
a title.
Even when parts of title are
deleted from the Playlist, the
original title will remain as it is.
The disc space to record will not
be increased.
Before you start
Editing discs in VR mode (Original / Playlist)
61
2006/02/15 17:26:47
Editing
Editing discs in VR mode (Original / Playlist) (cont’d)
Putting names on titles
4
VR
DVD-RW
You can put title names on the
titles and change the names from
this menu.
The names you put on the titles
will be displayed on a Title List.
POWER
Using [K / L], select “Yes”.
Press [ENTER].
The name you entered will be
activated for the title.
<Playlist>
.@/:
3
Playlist - Edit Title Name
1
A B C
a b c
1 2 3
@ !
?
A
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
Yes
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
2
3
4
K
{
B
L
REC SPEED
1
DEF
GHI
MY FAVORITE
Playlist - Edit Title Name
ABC
OPEN/CLOSE
No
2
Using [K / L], select “Edit Title
Name”. Press [ENTER].
A window for entering a title name
will appear.
<Playlist>
PROG.
0
1
Follow steps 1 to 3 on page 61
to display Original or Playlist
menu.
TIMER
ZOOM
Wait for a moment.
Bx1.3/0.8
REV
PL AY
h
B
SKIP
H
5
Press [RETURN ] and then
[RETURN ] or [STOP C] to
exit.
Data will be written onto the disc
momentarily.
REC/OTR
5
FWD
g
PAUSE
SKIP
F
G
STOP
CM SKIP
C
This operation may take a
while to be completed.
[ Guide to edit title name ]
JAN/ 1/06 1:00AM CH12 XP
0:00:59
3
To enter a title name, follow
the steps for “Guide to edit title
name” on this page.
character set
<Playlist>
[Step1]: Select a desired character set using [K/L], then
press [ENTER].
[Step2]: Follow the list below, press the Number buttons
repeatedly until the desired letter appears.
Select
Press
0
ABC
abc
123
@!?
<space>
<space>
0
<space>
Playlist - Edit Title Name
1
A B C
1
(*1)
(*1)
1
a b c
?
M
0:00:59
area for entering title names
When you finish entering a title
name, press [ENTER].
Confirmation window will appear.
e.g. character set :
ABC
press 2
A B C A...
! ”# $ % & ’( )
* + , - . / : ; < = > Note:
?@[]^_{|}
Undefined letters in a
1 2 3
@ !
ABC
abc
123
@!?
2
ABC
abc
2
(*2)
3
DEF
def
3
(*2)
4
GHI
ghi
4
(*2)
5
6
JKL
jkl
5
(*2)
MNO
mno
6
(*2)
7
8
PQRS
pqrs
7
(*2)
TUV
tuv
8
(*2)
9
WXYZ
wxyz
9
(*2)
title name are shown
by “*”. If you delete
them, adjoining letters
letters may change to
“*” or other.
*1 Press 1 , character set will be changed to the “ @!? ” mode automatically.
*2 Press 2 to 9 , character set will be changed to the previous input mode
automatically.
• To delete letters, press [CLEAR] repeatedly. Holding [CLEAR] to delete
all letters.
• Press [s / B] to move the cursor to the left or right.
• You can enter up to 30 letters.
62 EN
DVR91DG_E7A01UD.indd 62
2006/02/15 17:26:47
Editing
Before you start
Editing discs in VR mode (Original / Playlist) (cont’d)
Setting or clearing chapter markers
<Playlist :Delete>
VR
DVD-RW
Playlist - Chapter Mark - Delete
1
POWER
Yes
No
Chapter
.@/:
2/ 2
F
JAN/ 1/06 1:00AM CH12 XP
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0:00:59
Using [K / L], select “Chapter
Mark”. Press [ENTER].
Option window will appear.
<Playlist>
0
• You cannot delete the first
chapter of each title.
2
3
4
K
4
B
L
Using [K / L], select “Yes”.
Press [ENTER].
When you select “Add” at step 3, a
new chapter marker will be created
at the point you have decided.
<Playlist :Add>
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
5
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
3
C
Playlist - Chapter Mark - Add
1
Yes
No
Chapter
2/ 2
Playing discs
Playlist - Chapter Mark
1
REPEAT
Add
Delete
Chapter
JAN/ 1/06 1:00AM CH12 XP
2/ 2
Wait for a moment.
JAN/ 1/06 1:00AM CH12 XP
0:00:59
1
1
Yes
No
Chapter
2/ 2
JAN/ 1/06 1:00AM CH12 XP
Wait for a moment.
This operation may take
a while to be completed.
5
Yes
No
Chapter
Playlist - Chapter Mark - Delete
Others
Playlist - Chapter Mark - Add
When you select “Delete” at step
3, the chapter marker you have
selected will be deleted.
<Playlist :Delete>
Changing the
Setup menu
Use [SKIP H / G],
[REV E], [FWD D],
[PLAY B] and [PAUSE F] to
decide the point at which you
will create a new chapter marker.
Or, use [SKIP H / G] to
decide a chapter marker that
you will delete. Select “Add” or
“Delete” accordingly using
[K / L] . Press [ENTER].
Confirmation window will appear.
<Playlist :Add>
This operation may take a
while to be completed.
Editing
3
2/ 2
F
0:00:59
After this operation is completed,
press [RETURN ] twice and
then [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
Español
JAN/ 1/06 1:00AM CH12 XP
EN
DVR91DG_E7A01UD.indd 63
Recording
2
CH
Getting started
Follow steps 1 to 3 on page 61
to display Original or Playlist
menu.
A
GHI
{
1
OPEN/CLOSE
Connections
You can put chapter markers
in each title. Once a chapter is
marked, you can use it for the
chapter search feature.
You can put a chapter marker
anywhere you want.
When the number of chapter
markers in the Playlist comes to
999 in total, you cannot add any
more chapter markers.
63
2006/02/15 17:26:49
Editing
Editing discs in VR mode (Original / Playlist) (cont’d)
Setting pictures for thumbnails
VR
DVD-RW
You can set a picture to each title
for a thumbnail. It helps you to
remember the contents of the title
you are playing. The beginning
picture has been selected as the
default.
4
POWER
After this operation is completed, press [RETURN ] and
then [RETURN ] or [STOP C]
to exit.
Data will be written onto the disc
momentarily.
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
0
1
Follow steps 1 to 3 on page 61
to display Original or Playlist
menu.
B
L
2
REC SPEED
REV
Bx1.3/0.8
SKIP
h
Use [SKIP H / G],
[REV E], [FWD D], [PLAY B]
and [PAUSE F] to decide the
picture you want to select as a
thumbnail. Using [K / L], select
“Index Picture”. Press [ENTER].
Confirmation window will appear.
<Playlist>
2
3
K
{
H
4
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Playlist - Index Picture
1
Yes
No
F
JAN/ 1/06 1:00AM CH12 XP
0:00:59
3
Using [K / L], select “Yes”.
Press [ENTER].
A picture for thumbnail will be set.
<Playlist>
Playlist - Index Picture
1
Yes
No
JAN/ 1/06 1:00AM CH12 XP
Wait for a moment.
This operation may take a
while to be completed.
Note
• If a selected picture for a
thumbnail is deleted by
deleting a part of a title,
a default picture will be
selected.
64 EN
DVR91DG_E7A01UD.indd 64
2006/02/15 17:26:49
Changing the Setup menu
The following table is the contents which you can set and the default settings.
Refer to the following table for useful operation.
Setup
Items (highlight is the default)
English
French
Spanish
Set the language for the Disc menu.
Audio
Original
English
French
Set the language for audio.
Subtitle
OFF
English
French
Set the language for subtitle.
Digital Out
ON
OFF
ON
OFF
Progressive
Auto
Field
Frame
Parental Lock
All
level 8 to 1
Enter the current
four-digit password
(Change password)
Set whether the sound recorded
in 96kHz will be down sampled in
48kHz.
Set the type of sound signal which
outputs from the digital audio output
jack.
Compressing the range of sound
volume.
Set to the progressive scan mode
(set to “ON”) or to the interlace scan
mode (set to “OFF”).
Set the type of still image in pausing
playback.
Others
Still Mode
Set the brightness of the front panel
display.
Changing the
Setup menu
5.Parental setting
Pages 70-71
Set the display or undisplay of multiangle icon in a case the DVD in
playback mode contains multi-angle
scenes.
Set the time to work the screen
saver on the screen.
Editing
Dynamic Range
Control
4.Video setting
Pages 69-70
ON
OFF
OFF
5 minutes
10 minutes
Auto
Bright
Dark
PCM
48kHz
96kHz
Dolby Digital
PCM
Stream
FL Dimmer
3.Audio setting
Pages 68-69
Set the language for OSD
(On Screen Display).
Playing discs
Screen Saver
English
Français
Español
Recording
Angle Icon
Getting started
2.Display setting OSD Language
Pages 67-68
Connections
1.Language setting Disc Menu
Pages 66-67
Contents
Before you start
Tour of the Setup menu
Set the parental level of your DVD
discs.
Set and change the password.
Note
EN
DVR91DG_E7A01UD.indd 65
Español
• If you change the setting in the Setup menu, the information of
contents stays on even when the power is switched off.
• An item which is not currently available is grayed in Setup menus.
65
2006/02/15 17:26:50
Changing the Setup menu
Language setting
Press [STOP C] if you are playing a disc.
POWER
1
TIMER
ZOOM
PROG.
ABC
DEF
Press [SETUP].
.@/:
1
2
3
2
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
Using [K / L], select “Playback”. Press [ENTER].
Playback menu will appear.
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
3
Using [K / L], select “Language”. Press [ENTER].
Language menu will appear.
K
{
B
L
4
REC SPEED
Using [K / L], select a desired item. Press [ENTER].
Bx1.3/0.8
REC/OTR
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
H
F
SKIP
G
STOP
CM SKIP
1
2
3
4
C
Disc Menu Language (Default : English)
Set the language for Disc Menu.
Language - Disc Menu
Language
OPEN/CLOSE
Disc Menu
English
English
Audio
Original
French
Subtitle
OFF
Spanish
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
Other
Audio Language (Default : Original)
Set the Audio language.
Language
Language - Audio
Disc Menu
English
Original
Audio
Original
English
Subtitle
OFF
French
Spanish
Other
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
• When Original is selected, the
audio language will be in the
disc’s default language.
Subtitle Language (Default : OFF)
Set the Subtitle language.
Language - Subtitle
Language
Disc Menu
English
OFF
Audio
Original
English
Subtitle
OFF
French
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
Spanish
Other
Note
If “Other” is selected, press 4-digit code using the Number buttons.
Language - Subtitle
Code Input
-
-
-
-
• When you finish entering
the code, press [ENTER].
Refer to “Language code”
on page 75.
• Only the languages supported
by the disc can be selected.
• Audio Language setting may
not be available to some
discs.
• You can change or switch off
the subtitles on a DVD disc
also from the Disc menu if it
is available.
• Press [CLEAR] or [s] to erase
numbers entered incorrectly.
66 EN
DVR91DG_E7A01UD.indd 66
2006/02/15 17:26:51
POWER
Language setting (cont’d)
.@/:
5
Press [SETUP] to exit.
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
5
0
POWER
Press [STOP C] if you are playing a disc.
PROG.
ABC
L
DEF
OPEN/CLOSE
A
B
1
2
REC GHI
SPEED
REV
JKL
PL
AY
MNO
4
h
5
B
g
Bx1.3/0.8
PQRS
SKIP
TUV
PAUSE
WXYZ
SKIP
REPEAT
7
3
6
FWD
CH
H
F
9
G
SPACE
STOP
CLEAR
CMSETUP
SKIP
0
C
8
REC/OTR
DISPLAY
TOP MENU MENU/LIST RETURN
1
ENTER
Press [SETUP].
2
3
K
2
{
B
L
Using [K / L], select “Display”. Press [ENTER].
Display menu will appear.
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
3
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
Recording
C
Using [K / L], select a desired item. Press [ENTER].
OSD Language (Default : English)
Set the language for OSD.
OSD Language
English
English
Angle Icon
ON
Français
Screen Saver
10 minutes
Español
FL Dimmer
Bright
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
Display
OSD Language
Angle Icon
English
ON
OFF
ON
10 minutes
FL Dimmer
Bright
Changing the
Setup menu
Angle Icon
Screen Saver
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
Screen Saver (Default : 10 minutes)
Set the time to work the screen saver function on the screen.
Screen Saver
Display
English
OFF
Angle Icon
ON
5 minutes
Screen Saver
10 minutes
10 minutes
FL Dimmer
Bright
15 minutes
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
Others
OSD Language
Editing
Angle Icon (Default : ON)
Set to ON or OFF.
Playing discs
Display
OSD Language
Getting started
1
K
Connections
Display setting
{
.@/:
TIMER
ZOOM
Before you start
Changing the Setup menu
30 minutes
EN
DVR91DG_E7A01UD.indd 67
Español
Instructions continue on the next page.
67
2006/02/15 17:26:52
Changing the Setup menu
Display setting (cont’d)
FL Dimmer (Default : Bright)
Set the brightness of front panel display.
You can choose one among “Auto”, “Bright” and “Dark”.
Display
OSD Language
• Using [K / L], select a
setting. Press [ENTER].
Your setting will be activated.
• If “Auto” is selected, the
display is shown brighter when
OPEN/CLOSE
POWER
TIMER
the power is
darker when
ZOOMon,
PROG.
A
the power is off.
FL Dimmer
English
Auto
Angle Icon
ON
Bright
Screen Saver
10 minutes
Dark
FL Dimmer
Bright
ABC
.@/:
4
Press [SETUP] to exit.
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
CH
REPEAT
4
SETUP
0
POWER
TOP MENU MENU/LIST RETURN
TIMER
ZOOM
PROG.
Audio setting
Choose the appropriate Audio settings for your equipment.
It will only affect DVD discs during playback.
.@/:
1
ABC
2
{
GHI
JKL
4
5
RECPQRS
SPEED
7
DISPLAY
Bx1.3/0.8
K
L
A
DEF
3
MNO
B
CH
6
TUV
REV
WXYZ
PL
AY
h
8
B
9
g
CLEAR
PAUSE
SETUP
SKIP
SPACE
SKIP
H
0
Press [STOP C] if you are playing a disc.
OPEN/CLOSE
ENTER
F
STOP
TOP MENU MENU/LIST RETURN
REC/OTR
REPEAT
FWD
1
2
3
G
CMENTER
SKIP
C
1
K
{
B
L
Press [SETUP].
REC SPEED
REV
Bx1.3/0.8
SKIP
h
2
H
Using [K / L], select “Playback”. Press [ENTER].
Playback menu will appear.
REC/OTR
Note
Using [K / L], select “Audio”. Press [ENTER].
Digital Out
Set the digital audio output.
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Audio - Digital Out
Digital Out
Dynamic Range Control
A
B
• Dynamic Range Control
function is available only
on the discs which are
recorded in the Dolby
Digital format.
3
Audio
PL AY
PAUSE
ON
PCM
48kHz
Dolby Digital
Stream
• Using [K / L], select a
setting. Press [ENTER].
Option window will appear.
Proceed to step A or B.
Settings for PCM (Default : 48kHz)
Digital Out - PCM
48kHz
96kHz
• Using [K / L], select a setting. Press [ENTER]. Note
Your setting will be activated.
When playing disc with
48kHz :If your amplifier/decoder is NOT
copyright protection
compatible with 96kHz PCM, select
• Even if you select
“96kHz”, the sound will
“48kHz”. 96kHz sound will be output in
be down sampled at
48kHz.
48kHz.
96kHz :If your amplifier/decoder is compatible
with 96kHz PCM, select “96kHz”. 96kHz
sound will be output.
68 EN
DVR91DG_E7A01UD.indd 68
2006/02/15 17:26:53
Changing the Setup menu
B
Settings for Dolby Digital (Default : Stream)
PCM
Stream
Audio
Dynamic Range Control
• Using [K / L], select a setting.
Press [ENTER].
OPEN/CLOSE
POWER
Your setting
will be
TIMER activated.
Audio - Dynamic Range Control
Digital Out
ON
ON
OFF
4
PROG.
ABC
DEF
A
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
CH
REPEAT
4
0
K
Video setting
{
B
L
POWER
REC SPEED
OPEN/CLOSE
ZOOM
REV
TIMER
PROG.
PL AY
h
B
g
G
FWD
A
Progressive (Default : OFF)
ABC
.@/:
DEF
Bx1.3/0.8 SKIP
PAUSE
SKIP
This unit is compatible with the Progressive Scan System. The feature provides you with the
definition
images
1 higher
3
2
CH
JKL
GHI
MNO
than the traditional output system does. To utilize this feature, you must set Progressive Scan
CM SKIP
STOP “ON”.
REC/OTR mode to
Press [SETUP].
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
REPEAT
1
3
Using [K / L], select “Video”. Press [OK].
K
{
B
L
REC SPEED
Bx1.3/0.8
REV
PL AY
h
B
SKIP
H
REC/OTR
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Note
4
Using [K / L], select “Progressive”. Press [OK].
Activating progressive scan:
Check your TV has progressive scan
and connect with component video cable.
NOTE: If there is no picture or picture is
distorted after selecting “Yes”,
Wait about 15 seconds for auto recovery.
Activate?
Yes
No
EN
DVR91DG_E7A01UD.indd 69
Español
Instructions continue on the next page.
Others
Video - Progressive
• If your TV is compatible with Progressive
Scan (525p / 480p), you must use the
Component video cable (commercially
available) to connect this unit to the TV. (See
Method 2 on page 13.) If not, use the video
cable and set the Progressive Scan to
“OFF” or press and hold [SETUP] for more
than 3 seconds during DVD playback.
• When selecting “No” or not pressing any
keys on the unit or remote control within 15
seconds at step 5, Progressive Scan remains
to be “OFF” (interlace scan.)
Changing the
Setup menu
2
3
4
5
Using [K / L], select “Playback”. Press [OK].
Your setting will be activated.
Using [K / L], select “ON”.
Press [OK].
Confirmation window will appear.
6C
0
2
5
F
5
Editing
1
H
4
Playing discs
Press [SETUP] to exit.
Recording
.@/:
ZOOM
Getting started
Dynamic Range Control (Default : ON)
Set to ON to compress the range between soft and loud sounds.
Note
When playing a DVDRW disc recorded in VR
mode
• If the audio source on
a disc is Dolby Digital
format, set “Dolby
Digital” to “PCM” so
that you can switch to
main (L), sub audio
(R), or a mix of both
(L/R) with your
amplifier/decoder.
Connections
• Using [K / L], select a setting. Press [ENTER].
Your setting will be activated.
PCM
:Convert the Dolby Digital into PCM(2
channel).
When your amplifier/decoder is NOT
compatible with Dolby Digital, set to
“PCM”.
Stream :Outputs Dolby Digital signals.
When your amplifier/decoder is compatible
with Dolby Digital, set to “Stream”.
Digital Out - Dolby Digital
Before you start
Audio setting (cont’d)
69
2006/02/15 17:26:54
POWER
Changing the Setup menu
Video setting (cont’d)
6
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
Using [s / B], select “Yes”. Press [OK].
7
K
{
B
L
Using [K / L], select “Yes” within 15 seconds. Press [OK].
8
Press [SETUP] to exit.
Still Mode (Default : Auto)
Set the type of still image in pausing playback.
REC SPEED
REV
POWER
h
PL AY
FWD
B
g
OPEN/CLOSE
TIMER
Bx1.3/0.8
ZOOM
SKIP
H
F
SKIP
A
G
.@/:
REC/OTR
ABC
DEF
STOP
CM SKIP
PROG.
PAUSE
1
2
3C
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
1
REPEAT
K
{
B
L
Press [SETUP].
2
REC SPEED
REV
Bx1.3/0.8
SKIP
PL AY
B
h
PAUSE
H
Using [K / L], select “Playback”. Press [ENTER].
3
Using [K / L], select “Video”. Press [ENTER].
4
Using [K / L], select “Still Mode”. Press [ENTER].
5
Using [K / L], select a setting. Press [ENTER].
Your setting will be activated.
REC/OTR
6
7
CH
0
Press [STOP C] if you are playing a disc.
8
FWD
g
SKIP
F
G
STOP
CM SKIP
C
1
2
3
4
5
Auto:
Field:
Optimum setting is selected.
Flicker-free images are played back
in pause playback mode.
Frame: Higher-resolution images are played
back in pause playback mode.
Note
• Frame is 1 completed video image made
up of 2 fields (There are 30 frame per
second of NTSC video).
Settings for Parental lock level
Some DVD-Video discs feature a Parental Lock level. Playback
will stop if the ratings exceed the levels you set, it will require you
to enter a password before the disc will playback. This feature
prevents your children from viewing inappropriate material.
POWER
.@/:
Press [STOP C] if you are playing a disc.
1
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
Using [K / L], select the desired level. Press [ENTER].
CH
REPEAT
7
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
K
Using [K / L], select “Playback”. Press [ENTER].
Playback menu will appear.
4
A
DISPLAY
2
Using [K / L], select “Parental Lock”. Press [ENTER].
OPEN/CLOSE
0
Press [SETUP].
3
TIMER
ZOOM
{
B
L
REC SPEED
Note
Bx1.3/0.8
REV
PL AY
h
B
FWD
4
1
2
3
4
g
SKIP
PAUSE
SKIP
H
F
G
• Parental lock function may not be
REC/OTR
available to some
discs. STOP CM SKIP
• With some DVDs, it may be difficult to find
if they are compatible with parental lock. Be
sure to check if the parental lock function
operates in the way that you have set.
• Record the password in case you forget it.
C
70 EN
DVR91DG_E7A01UD.indd 70
2006/02/15 17:26:55
Changing the Setup menu
Before you start
Settings for Parental lock level (cont’d)
Parental Lock (Default : All)
Set the Parental Lock level.
All
Video
8
7
Language
Parental Lock
6
All
5
4
Connections
• Using [K / L], change
the parental level. Press
[ENTER].
Option window will appear
Proceed to step A or B.
Parental Lock
Playback
Audio
3
2
1
A
Parental Lock
Getting started
A password has not been set yet.
Parental Lock
Change Password?
Yes
Yes
No
Password Input
-
-
-
Recording
Playing discs
• Using the Number buttons,
enter a new password. Press
[ENTER].
Your setting will be activated.
• Using [K / L], select “Yes”.
Press [ENTER].
If you select “No”, proceed
to step 5.
B
-
A password has been set already.
<Change the password>
Parental Lock
Parental Lock
Change Password?
* * * *
Yes
Password Input
No
• Using [K / L], select “Yes”.
Press [ENTER].
If you select “No”, proceed to
step 5.
-
-
-
• Using the Number buttons,
OPEN/CLOSE
POWER
TIMER
enter a new
Press
ZOOM password.
PROG.
A
[ENTER]. ABC
.@/:
DEF
Your setting
1
2 will 3be activated.
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
5
0
Press [SETUP] to exit.
K
{
Others
5
-
Changing the
Setup menu
• Using the Number buttons,
enter the current password.
Yes
Editing
Password Input
Parental Lock
B
L
REC SPEED
Note
Bx1.3/0.8
REV
PL AY
h
B
FWD
g
SKIP
PAUSE
SKIP
H
F
G
C
EN
DVR91DG_E7A01UD.indd 71
Español
• Press [CLEAR] to erase numbers entered incorrectly.
CM SKIP
STOP
REC/OTR
• When you forget the password or you want to clear all settings in Parental lock, enter
4,7,3,7 using
the
Number buttons in Password Input window. Password will be cleared and parental levels will be set to “All”.
71
2006/02/15 17:26:56
Others
Troubleshooting
Before requesting service for this unit, check the table below for a possible cause of the problem you are
experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore
proper operation.
Symptom
Power
The power does not turn on.
Picture
There is no picture.
Remedy
• Check that the AC power cord is connected securely.
• (In case of power failure) Check the breaker.
• Re-connect the connecting cords securely.
• Check if the connecting cords are damaged.
• If Setup menu appears on the TV screen, press [RETURN ] to
exit the menu.
• Check the connection to your TV (page 13).
• Check if the INTERLACE/PROGRESSIVE mode is set correctly
according to your TV (page 13).
• Switch the input selector on your TV (such as to “LINE1”) so that
the signal from the unit appears on the TV screen.
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output signal from the unit passes through your VCR
to get to your TV, or if you are connected to a combination TV/
VIDEO player, the copy-protection signal applied to some DVD
programs could affect picture quality. If you still experience this
problem even when you connect the unit directly to your TV, try
connecting the unit to your TV’s S-VIDEO input.
TV program reception does not fill
the screen.
• Try to set the channels with “Auto Preset” in the Setup menu (page 18).
• Select a channel of any TV program using [CH K / L].
TV program pictures are distorted.
• Adjust TV antenna.
• Adjust the picture (see the TV’s instruction manual).
• Place the unit and TV farther apart.
• Place the TV and any bunched antenna cables farther apart.
TV channels cannot be changed.
• Switch the input to TV.
• Connect the antenna cable correctly (page 13).
Playback picture is distorted
• Keep the equipment which may cause electrical disturbances,
such as a cellular phone, away.
The playback picture or TV program
from the equipment connected
through the unit is distorted.
• If the playback picture output from a DVD player, VCR or tuner
goes through the unit before reaching your TV, the copy-protection
signal applied to some programs could affect picture quality.
Disconnect the playback equipment in question and connect it
directly to your TV.
Sound
There is no sound.
• The disc is dirty or flawed.
• Re-connect all connections securely.
• Check if the connecting cord is damaged.
• Check the connections to the amplifier input.
• The input source setting on the amplifier is incorrect.
• The recorder is in pause mode or in slow forward / slow reverse play.
• The recorder is in fast forward or fast reverse mode.
• If the audio signal does not come through the DIGITAL OUT
(COAXIAL) jack, check the Audio settings (pages 68-69).
Sound is noisy.
• The disc is dirty or flawed.
No DTS sound is output.
• This unit is not compatible with DTS sound.
Remote control
The remote control does not work.
• Check the antenna or cable connection to the main unit.
• Check the battery life of the remote control.
• Check if there is an obstacle between the sensor and the remote
control.
• Test the signal output. If OK, then possible remote sensor trouble.
(Refer to “IR SIGNAL CHECK” on page 5.)
72 EN
DVR91DG_E7A01UD.indd 72
2006/02/15 17:26:56
Others
Symptom
Remedy
Playback
• During the playback of two layered disc, picture may freeze for a
moment when the 1st layer switches to the 2nd layer. This is not a
malfunction.
The disc does not start playback
from the beginning.
• Resume play was activated (page 41). Press [STOP C] twice.
• You have inserted a disc whose Title menu or DVD menu
automatically appears on the TV screen when it is first insert.
The unit starts playing from the disc
automatically.
• The DVD-Video features an auto playback function.
Some functions such as Stop,
Search, or Slow-motion Play cannot
be performed.
• Depending on the disc, you may not be able to do some of the
operations above. See the instruction manual supplied with the
disc.
The language for the sound track
cannot be changed.
• Multilingual tracks are not recorded on the DVD-Video, DVD-R or
DVD-RW being played.
• The DVD-Video prohibits the changing of the language for the
sound track.
• Try changing the language using the DVD-Video’s menu.
The subtitle language cannot be
changed or turned off.
• Multilingual subtitle are not recorded on the DVD-Video.
• The DVD-Video prohibits changing of the subtitles.
• Try changing the subtitle using the DVD-Video’s menu.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD-Video being played.
• The angle-change operation is whenever possible as long as
the disc contains a multi-angle portion. Actual change will be
performed when the portion has come up.
• The DVD-Video prohibits changing angles.
• Try changing the angle using the DVD-Video’s menu.
Recording
Playback image freezes for a
second.
Playing discs
Editing
Recording does not start immediately • An unused DVD-R or DVD-RW has been inserted. It takes a while
for the unit to automatically format a DVD-RW.
after you press [REC/OTR].
Others
• There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted
for more than 30 seconds. Reset the clock (pages 21- 22).
• Disconnect the AC power cord from the AC outlet, and connect it
again.
• The program contains copy protection signals that restricts
copying.
• The timer setting overlapped with another setting that was set later
or has priority.
Changing the
Setup menu
Recording/Timer Recording/Editing
The channel cannot be changed from • Set the TV’s input to “TV”.
the channel you are recording.
Nothing was recorded even though
you set the timer setting correctly.
Getting started
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side
facing up.
• The disc is not correctly inserted.
• The unit cannot play certain discs (such as a CD-ROM) (page 37).
• The region code on the DVD-Video does not match the unit (page
37).
• Moisture has condensed inside the unit. Remove the disc and
leave the unit turned on for about two hours until the moisture
evaporates (page 4).
• If the disc was recorded on another recorder, the unit cannot play
the disc if it was not finalized (page 35).
Connections
The disc does not play.
Before you start
Troubleshooting (cont’d)
Recording does not stop immediately • It will take a few seconds for the unit to input disc data before
recording can stop.
after you press [STOP C].
• The timer setting overlapped with another setting that was set
previously has priority (page 32).
• Disc space was not enough.
EN
DVR91DG_E7A01UD.indd 73
Español
Timer Recording is not completed or
did not start from the beginning.
73
2006/02/15 17:26:57
Others
Troubleshooting (cont’d)
Symptom
Remedy
Others
The unit does not operate properly.
The disc tray does not open when
you press [OPEN/CLOSE A].
• When static electricity, etc., causes the unit to operate abnormally,
unplug the unit and then plug it in again.
• It may take a few seconds for the disc tray to open after you have
recorded or edited a disc.
“Repairing” appears on the TV screen. • If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after “Wait for a moment.” message
is disappeared), a Repairing process will begin automatically just
Repairing
after turning the unit on again.
It may take several minutes up to about four hours.
In a case you intend to cancel the
• If you intend to cancel the Repairing process, press
Repairing process.
[OPEN/CLOSE A] on the front panel, then select “Yes” with
[{ / B] and press [ENTER]. After that, the disc tray will
Do you want to cancel a repairing process ?
When selecting “Yes”, the disc may not be
automatically open. In case the Repairing process is canceled,
usable.
the disc MAY NOT work.
Yes
No
Repairing
Error message
Cause
Solution
Disc Error
--- Please eject the disc. --Playback feature may not be
available on this Disc.
• Unplayable disc is inserted in the
unit.
• The disc is upside down.
• Insert the standardized disc which
bear the marks on page 37.
• Insert the disc with the labeled
side facing up.
Region Error
--- Please eject the disc. --Playback is not authorized in your
region.
• Playback is not authorized in the
region of the DVD-Video disc
which you inserted in the unit.
• Insert the DVD-Video disc with
region codes 1 or ALL.
Parental Lock On
The current selected parental level
prohibits playback.
• The current selected parental
level in the Setup menu prohibits
playback.
• Check the “Parental Lock” setting
(pages 70-71).
Recording Error
This program is not allowed to be
recorded.
• The recording function
encountered the copy prohibited
program.
• You cannot record copy prohibited
programs.
Recording Error
This program is not recordable in
Video mode.
• You are trying to record the copyonce program onto the DVD-RW
disc in Video mode.
• Set “Format mode” to “VR mode”
(page 26).
Recording Error
Can not record on this disc.
• You are trying to record onto the
disc which is unrecordable, or the
disc status is unable to record.
• The disc is dirty.
• The disc is damaged.
• Insert the recordable disc, and
ensure the disc status satisfies the
recording requirements
(pages 24-25).
• Clean the disc with a cleaning cloth.
• Replace the disc.
Recording Error
This program is not allowed to be
recorded on this disc.
• You are trying to record the copyonce program onto the DVD-RW
disc which is not compatible with
CPRM.
• Insert the DVD-RW disc in VR
mode (ver.1.1 or 1.2 compatible
with CPRM).
Recording Error
This disc is protected and not
recordable.
• You are trying to record on to the
protected disc which is set in the
Disc menu.
• Release the disc protect setting in
the Disc menu (page 34).
Recording Error
Disc is full.
(No area for new recording)
• You are trying to record onto
the disc which has no space for
recording.
• Insert the recordable disc with
enough recording space.
74 EN
DVR91DG_E7A01UD.indd 74
2006/02/15 17:26:58
Others
Before you start
Troubleshooting (cont’d)
Error message
Cause
Solution
Recording Error
You cannot record more than 999
chapters on one disc.
(The maximum is 999)
You are trying to record onto the
VR mode DVD-RW disc on which
the number of recording chapters
comes up to the maximum (999).
Delete unnecessary chapter
markers (page 63).
Recording Error
You cannot record on this disc as
Control Information is full.
This disc has no space to write the Delete unnecessary titles
Control Information when recording (pages 51, 54).
or deleting contents.
When editing has been repeatedly
performed, the control Information
area may come up to be full even the
recording area has enough space.
Recording Error
You cannot record on this disc as
Power Calibration Area is full.
When recordings are performed
repeatedly onto an unstable disc,
this area may come up to be full.
Getting started
Delete unnecessary titles
(pages 51, 54).
Connections
Recording Error
You cannot record more than 99
titles on one disc.
(The maximum is 99)
You are trying to record onto
the disc on which the number of
recording titles comes up to the
maximum (99).
Insert a new disc.
You are trying to record onto
the disc already finalized.
Release the finalizing for this
disc (page 35).
* If you are still having trouble with the unit after checking “Troubleshooting”, write down the error code and the
error description for calling our help line mentioned on the front page to locate an Authorized Service Center.
Language code
Language
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Occitan
Oriya
Oromo (Afan)
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Romanian
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Code
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
Language
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
EN
DVR91DG_E7A01UD.indd 75
Español
Code
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
Others
Language
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Lingala
Changing the
Setup menu
Code
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
Editing
Language
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
Playing discs
Recording Error
This disc is already finalized.
Recording
Every time you insert a disc for
recording, the disc’s working area
will be taken up. And if you repeat
this frequently, it will be used up
sooner and you may not be able to
record full 99 titles.
75
2006/02/15 17:26:59
Others
Glossary
Analog audio
Dolby Digital
Regions code
An electrical signal that directly
represents sound. Compare this
to digital audio which can be an
electrical signal, but is an indirect
representation of sound. See also
Digital audio.
The system to compress digital
sound developed by Dolby
Laboratories. It offers you sound of
stereo(2ch) or Multi-channel audio.
Regions associate discs and
players with particular areas of the
world. This unit will only play discs
that have compatible region codes.
You can find the region code of
your unit by looking on the rear
panel. Some discs are compatible
with more than one region (or all
regions).
Aspect ratio
The width of a TV screen relative
to its height. Conventional TVs
are 4:3 (in other words, the screen
is almost square); widescreen
models are 16:9 (the screen is
almost twice as wide as it is high).
Chapter
Just as a book is split up into
several chapters, a title on a
DVD disc is usually divided into
chapters. See also Title.
Component video output
Each signal of luminance(Y)
and component(Pb/Cb, Pr/Cr) is
independent to output so that you
can experience picture color as it is.
Also, due to compatibility with
progressive video (525p/480p),
you can experience higher-density
picture than that in interlace
(525i/480i).
CPRM
(Content Protection for
Recordable Media)
CPRM is a copy protection system
with scramble system regarding
the recording of “copy-once”
broadcast programs (e.g. some
satellite broadcasts).
Digital audio
An indirect representation of sound
by numbers. During recording,
the sound is measured at discrete
intervals (44,100 times a second
for CD audio) by an analog-todigital converter, generating a
stream of numbers. On playback,
a digital-to-analog converter
generates an analog signal based
on these numbers. See also
Sampling frequency and Analog
audio.
Finalize
To make DVD discs, which have
been recorded on, possible to play
in DVD players. With this unit, it is
possible to finalize DVD-R/DVDRW discs.
PCM
(Pulse Code Modulation)
The most common system of
encoding digital audio, found on
CDs and DAT. Excellent quality,
but requires a lot of data compared
to formats such as Dolby Digital
and MPEG audio. For compatibility
with digital audio recorders (CD,
MD and DAT) and AV amplifiers
with digital inputs, this unit can
convert Dolby Digital and MPEG
audio to PCM. See also Digital
audio.
Sampling frequency
The rate which sound is measured
by a specified interval to turn into
digital audio data. The numbers of
sampling in one second defines
as sampling frequency. The higher
the rate, the better the sound
quality as possible as it is.
SAP
(Secondary Audio Program)
Sub audio channel which is
delivered separately from mainaudio channel. This audio channel
is used as an alternate in bilingual
broadcasting.
Playlist
S-Video output
From this list you can play
contents of a disc as your desired
order or in sequence. Also it is
allowed to search a specific scene
directly.
It delivers independently
each signal of color(C) and
luminance(Y) to TV as video
signals, so that higher-quality
picture will be gained.
Progressive Scan (525p/480p)
Title (DVD only)
A type of display that does not
split each frame into fields, and
instead scans directly through
all the scanlines of each frame
in order. Progressive Scan
provides less flickering and higher
image resolution than traditional
(525i/480i) TV signals. Refer
to page 13 for instructions on
selective Progressive Scan mode.
A collection of chapters on DVD
disc. See also chapter.
Track
Audio CDs use tracks to divide up
the content of a disc. The DVD
equivalent is called a chapter. See
also Chapter.
Frequently Asked Questions
–– Can I record to CD-R/RW?
No, this unit records only DVDs.
–– Can I play DVD-Video that is bought in another country?
Possible when the region code of the disc is 1 and All.
–– Is this unit JPEG compatible?
No.
–– Can I connect the unit to my PC?
No, you cannot control the unit by PCs.
76 EN
DVR91DG_E7A01UD.indd 76
2006/02/15 17:26:59
Others
Before you start
Specifications
13.5MHz
MPEG
48kHz
Dolby Digital
Recording
2-13ch
14-69ch
C1-C125ch
VHF/UHF set 75W
Input 1 (rear), 2 (front)
1 Vp-p (75W)
RCA jacks
Output 1 (rear)
1 Vp-p (75W)
RCA jack
Input 1 (rear), 2 (front)
1 Vp-p (75W)
286 mVp-p (75W)
4 pin mini DIN
Output 1 (rear)
1 Vp-p (75W)
286 mVp-p (75W)
4 pin mini DIN
Output 1 (rear)
Y: 1.0 Vp-p (75W), PB/CB, PR/CR: 0.7 Vp-p (75W)
RCA jacks
Input 1 (rear), 2 (front) L/R
2V rms (Input impedance: more than 22kW)
RCA jacks
Output 1 L/R (rear)
2V rms (Output impedance: less than 1kW)
RCA jacks
Output 1 (rear) COAXIAL
500 mVp-p (75W)
RCA jack
Playing discs
Editing
Changing the
Setup menu
Others
Tuner
Receivable channels
VHF
UHF
CATV
Input / Output
VHF/UHF antenna input/output terminal
Video input
Input level
Jacks
Video output
Output level
Jack
S-Video input
Y (Iuminance) - Input level
C (color) - Input level
Jacks
S-Video output
Y (Iuminance) - Output level
C (color) - Output level
Jack
Component video output
Output level
Jacks
Audio input
During audio input
Jacks
Audio output
During audio output
Jacks
Digital audio output
Output level
Jack
Video Recording format (DVD-RW only),
Video format (DVD-RW, DVD-R)
DVD-Rewritable, DVD-Recordable
Getting started
Recordable discs
Video recording format
Sampling frequency
Compression format
Audio recording format
Sampling frequency
Compression format
DVD-Video, DVD-RW/R, CD-DA, CD-RW/R
AC120 V, 60 Hz
20 W (standby: 2.8 W)
5.1 lbs ( 2.3 kg )
17 3/16” x 2 5/8” x 9 5/8” (435 x 66 x 244 mm)
41Fº to 104Fº (5ºC to 40ºC)
Less than 80% (no condensation)
NTSC
Connections
General
System
Power requirements
Power consumption
Weight
Dimensions (width x height x depth)
Operating temperature
Operating humidity
TV format
Recording
Recording format
Español
Note:
The specifications and design of this product are subject to change without notice.
EN
DVR91DG_E7A01UD.indd 77
77
2006/02/15 17:26:59
Español
Fácil grabación de DVD
Estas instrucciones le ayudarán a entender fácilmente cómo grabar discos DVD.
Nota:
Asegúrese que las pilas están en el mando a distancia y que ha conectado correctamente esta unidad y el TV.
Paso 2: Coloque un disco en blanco.
Paso 1: Elija un tipo de disco.
Puede elegir entre distintos tipos de discos DVD
grabables. Elija un tipo de disco DVD grabable de
acuerdo con sus necesidades de reproducción/
grabación. Vea los “Tipos de discos DVD” en la parte
inferior de esta página para más detalles sobre las
diferencias entre los distintos medios compatibles.
Este grabador de DVD puede grabar los
siguientes tipos de discos.
Mando a distancia
POWER
1
TIMER
ZOOM
PROG.
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
TUV
WXYZ
Para
PQRS
7
encender DISPLAY
OPEN/CLOSE
A
CH
REPEAT
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
3
0
(o)
2
Para abrir
K
{
B
L
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
H
F
Por ejemplo, cuando desea grabar repetidamente en el mismo disco o cuando desea editar
el disco después de grabar, seleccione el
disco de tipo regrabable DVD-RW.
Cuando desea guardar grabaciones sin alterarlos, un DVD no regrabable DVD-R puede ser
más conveniente.
REC/OTR
POWER
.@/:
TIMER
ZOOM
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
STOP
OPEN/CLOSE
C
g
SKIP
G
CM SKIP
A
4
Para cerrar
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
FWD
B
h
Cargando
EstaK operación puede
B
demorar en
reconocerse.
{
L
REC SPEED
REV
h
Bx1.3/0.8
SKIP
H
REC/OTR
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
Tipos de discos DVD
: Más adecuado
: Puede utilizar
Desea
Formato del disco
: Algunas funciones son limitadas
DVD-RW VR
: No puede utilizar
DVD-RW Video
DVD-R
DVD-RW VR
DVD-RW Video
DVD-R
¿Regrabable?
Sí
Sí
No
Puede crear capítulos a intervalos fijos (auto.)
Sí
Sí
Sí
Puede crear capítulos donde desee (manual)
Sí
No
No
Puede grabar imágenes de tamaño 16:9
Sí
Sí
Sí
Puede grabar un programa de Copia-una-vez
Sí
No
No
Grabar programas de TV
Volver a utilizar borrando partes no deseadas
Editar las grabaciones
Editar/grabar de equipos conectados
Copiar discos para distribución
*1
Reproducir en otro equipo de DVD
*1
Detalles
Grabación
Edición
*1
Puede hacer funciones de edición básica
Sí
Sí
Sí
Puede hacer funciones de edición avanzadas (edición de lista a reproducir)
Sí
No
No
El DVD-RW (modo VR) sólo puede reproducirse
en equipos de DVD compatibles con VR.
Nota:
Para más detalles sobre las funciones anteriores y las
limitaciones implícitas, lea las explicaciones en este manual.
Coloque el disco en el
grabador. Haga el formato
del disco del menú SETUP,
existen los formatos de
video (modo de Video) o de
grabación de video (modo
VR) según el tipo de disco
colocado.
Esto es necesario para
preparar el disco para grabación. Vea los detalles
en las páginas 26-27.
* Al formatear, todo el
contenido de ese disco se
borrará.
* La unidad empieza
a formatear
automáticamente cuando
se inserta un disco DVDRW no usado.
78 ES
DVR91DG_E7A01UD.indd 78
2006/02/15 17:27:00
Español
.@/:
1
TIMER
ZOOM
PROG.
ABC
DEF
OPEN/CLOSE
A
Fácil grabación de DVD (cont.)
.@/:
3
2
CH
Paso 3:Seleccione la
velocidad de
grabación.
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
Paso 4:Seleccione el
canal des
eado.
PROG.
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
OPEN/CLOSE
A
CH
Paso 5: Grabe en discos DVD.
TUV
PQRS
WXYZ
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
Connections
POWER
B
PL AY
TIMER
ZOOM
L
PROG.
REC SPEED
REV
g
1
2
3
Bx1.3/0.8
SKIP
PAUSE
SKIP
GHI
JKL
MNO
H
F
G
4
5
6
STOP
CM SKIP
PQRS
TUV
WXYZ
REC/OTR
TIMER
ZOOM
K
K
{
h
POWER
B
FWD
.@/:
ABC
OPEN/CLOSE
B
L
A
DEF
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
H
F
G
STOP
CM SKIP
REC/OTR
REPEAT
FWD
g
B
h
CH
SKIP
C
8
9
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
Getting started
7
DISPLAY
C
{
0
K
B
CH
{
12
L
REC SPEED
REV
Bx1.3/0.8
SKIP
h
H
XP
REC/OTR
0:58
PL AY
B
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
C
POWER
Sugerencia 1: Reproduzca el contenido grabado
Inicio de grab.
¿Qué son títulos y capítulos?
Parada grab.
ABC
DEF
1
2
3
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
OPEN/CLOSE
A
CH
REPEAT
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
Capítulo 1 Capítulo 2 Capítulo 3 Capítulo 1 Capítulo 2
Sugerencia 2: Edite el disco grabado
.@/:
GHI
Título 2
El contenido de un disco DVD se divide generalmente en títulos. Los títulos pueden dividirse a su vez en capítulos.
Start Rec.
PROG.
Paso 6: Pare la K
grabación.
{
B
L
REV
Bx1.3/0.8
SKIP
PAUSE
H
F
G
STOP
CM SKIP
REC/OTR
La edición de discos es fácil. Esta unidad ofrece convenientes funciones de
Track 1 Track 2 Track 3 Track 4 Track 5
edición que sólo son posibles con discos DVD-RW/R.
PL AY
REC SPEED
h
Stop Rec.
B
FWD
g
SKIP
C
Editing
Puede editar lo siguiente de la lista de títulos.
Poniendo nombres en títulos
Seleccionando imágenes para índices
Seleccionando/borrando marcadores de capítulos
Borrado de títulos o escenas
Changing the
Setup menu
•
•
•
•
(Las funciones editables dependen del modo de grabación y forma de edición.)
Original y Playlist (modo VR)
Puede editar las grabaciones en la lista a reproducir sin cambiar las grabaciones
originales. Cualquier lista a reproducir no ocupa mucho espacio en el disco.
¿Qué significa “Original” o “Playlist”?
Escrit de datos
90%
Others
A lo largo de este manual encontrará Original y Playlist que se refieren a las grabaciones reales y la versión editada.
• La grabación Original se refiere a la grabación real en el disco.
• El Playlist se refiere a la versión editada del disco; cómo se va a reproducir la
versión Original.
Finalización de un disco
C
Esta operación puede
demorar en completarse.
ES
DVR91DG_E7A01UD.indd 79
Español
• Esto permitirá que un disco que se grabe en nuestra unidad pueda ser
reproducido en un reproductor DVD diferente. Un disco sin finalizar no se podrá
reproducir en otro reproductor.
• Después de finalizar un disco, si la grabación se hizo en el modo de vídeo,
usted no podrá editar ninguna información que se encuentre en ese disco.
• Si ha grabado en el modo VR en un disco DVD-RW, la edición podrá realizarse
incluso después de la finalización.
Playing discs
Título 1
Parada/inicio
TIMER
ZOOM
Recording
I
Puede seleccionar el título que desea
reproducir de un menú indicado y empiece
a reproducir inmediatamente. El contenido
grabado se puede acceder fácilmente con un
simple procedimiento de elegir un título en un
capítulo en la pantalla del menú.
Before you start
POWER
79
2006/02/15 17:27:01
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Certain parts are excluded from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from
the date of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original
retail purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,
missing or if service was attempted by an unauthorized service center. This limited warranty does not
apply to any product not purchased and used in the United States.
This product is produced for home use and this warranty only covers failures due to defects in material
or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or
failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage
which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation,
improper maintenance, commercial use such as hotel, rental or office use of this product or damage which
results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT
REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR
MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR
ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED
BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE
PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS
MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID
WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD,
YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE
CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid,
in either its original packaging or packaging affording an equal degree of protection, to any
AUTHORIZED SERVICE CENTER. FUNAI CORP. will not reimburse you for any service done
by unauthorized service providers without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at:
FUNAI CORPORATION
Customer Service
Tel :1-800-605-8453
http://www.SylvaniaConsumerElectronics.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
DVR91DG_E7A01UD.indd 80
1VMN22666 / E7A01UD ★★★★★
2006/02/15 17:27:01
1
Connections
Antenna
Cable
TV signal
(Back of TV)
VIDEO
or
IN
DVD Recorder
RF cable (not supplied)
Connect
Video
cable
(supplied)
S-VIDEO
OUT
IN
R
PR/CR
AUDIO IN
Disc
I Both A/V and RF cables must be connected to the TV for operation.
I See front page of the Owner's Manual for the connection with the RF modulator.
Logo
DVD-VIDEO
CD-DA (AUDIO CD)
DVD-RW (VIDEO/VR mode)
CD-RW (CD-DA FORMAT)
2
Watching TV/DVD
2 – 1 DVD Playback
Press [POWER] to
turn the unit on.
DVD-R (VIDEO mode)
COAXIAL
AUDIO OUT
(Back of this unit)
This unit is compatible to play the following discs.
Logo
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
L
PB/CB
R
ANTENNA
(L1)
Disc
VIDEO OUT
Y
L
OUT
Connect
P l a y ab le dis c s
Connect
Audio
cable
(supplied)
COMPONENT
VIDEO OUTPUT
VIDEO IN
IN
1
4
3
2
OUT
Connect
RF
cable
(supplied)
DVR91DG
AUDIO IN
(Cable box or
Satellite box)
POWER
ZOOM
CD-R (CD-DA FORMAT)
.@/:
is a trademark of DVD Format/Logo Licensing Corporation.
I DVD+R/+RW discs can be played back only on this unit.
ABC
TIMER
OPEN/CLOSE
PROG.
Insert a disc.
Press [OPEN/CLOSE] to
open the disc tray.
A
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
PL AY
FWD
CH
disc tray
guide
REPEAT
After you have completed connections;
ENTER
TOP MENU MENU/LIST RETURN
Press the input selector
button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input
channel (usually near channel 0) for viewing the picture from this unit.
K
Please refer to “Input Mode Names
for Common TV Brands” on page 15 of the Owner's manual or the manual accompanying
{
B
your TV.
L
0
R e g ion c od e s
The number inside the globe refers to region of the world.
This unit can play DVDs that are labeled for ALL regions or for Region 1.
REC SPEED
h
Bx1.3/0.8
REC/OTR
R e co rd ab le d is c s
Disc format
Functions
Attributes
Playing, limited recording,
limited editing
8cm/12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB) (for 12cm)
180 minutes (1.4GB) (for 8cm)
DVD-RW
VR mode
VR
DVD-RW
Video mode
DVD-R
DVD-R: 2x.4x.8x
• We strongly recommend using any DVD-R 8x,
MAXELL DVD-R 16x and DVD-RW 4x
disc to assure good recording quality.
• Discs that have been tested and are proven to be
compatible with this recorder:
VERBATIM DVD-R 8x VERBATIM DVD-RW 2x
MAXELL DVD-R 16x
JVC DVD-RW 4x
Video mode
Video
DVD-RW: 1-4x
g
B
SKIP
PAUSE
H
F
G
STOP
CM SKIP
SKIP
1. Turn on the TV and the unit in Cthe
first time. “Initial Setting” will appear.
Using [K / L], select your desired
language for the OSD. Then press
[ENTER] to go to next step.
This unit can record to DVD-R and DVD-RW discs.
DVD-R discs can only be recorded to once, and cannot
be erased. DVD-RW discs can be recorded to and erased
many times.
DVD-R discs can only be recorded in Video mode, while
DVD-RW discs can select a recording format between Video
mode and VR mode.
Disc type
REV
2 – 2 Initial Setting
Playing, recording,
Original/Playlist editing
Playing, limited recording,
limited editing
8cm/12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB) (for 12cm)
180 minutes (1.4GB) (for 8cm)
2. Press [ENTER] to start Channel
Preset. The unit will start getting
channels available in your area.
3. Clock Setting menu will appear.
Press [ENTER] twice, default date
will appear.
Initial Setting
Initial Setting
CH 1
English
Français
Español
Auto Presetting Now
4. Using [K / L], enter the date
(month / day / year).
Press [{ / B] to move the cursor.
Initial Setting
5. Using [K / L], enter the time
(hour / minute). Press [{ / B].
A cursor will move on AM.
Initial Setting
FEB/ 01 / 2006(WED)
12: 00 AM
FEB/ 01 / 2006(WED)
12: 00 AM
JAN/ 01 / 2006(SUN)
12: 00 AM
6. Press [K / L] to select “AM” or
“PM”. Press [ENTER].
TV Program will automatically
appear. (usually near channel 0)
Playing, recording, and editing discs
are available on this unit.
Follow to the back side of this sheet.
DVR91DG_E7A01UD_QG_EN.indd 1
2006/02/08 13:42:11
POWER
3
3 –1
TIMER
ZOOM
PROG.
.@/:
ABC
DEF
1
2
3
JKL
MNO
5
6
PQRS
TUV
WXYZ
7
8
9
GHI
4
OPEN/CLOSE
Easy Recording
CH
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
REC SPEED
REV
Bx1.3/0.8
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
B
REC/OTR
Disc Size
FWD
8cm Disc
g
C
Select the desired
channel.
POWER
.@/:
1
TIMER
ZOOM
PROG.
ABC
DEF
JKL
MNO
4
5
6
PQRS
POWER
TUV
WXYZ
7
DISPLAY
A
3
2
GHI
OPEN/CLOSE
TIMER
9
PROG.
CLEAR
8
ZOOM
SPACE
CH
A
SETUP
0
ABC
.@/:
DEF
RETURN
TOP 1MENU MENU/LIST
3
2
ENTER
GHI
JKL
MNO
CH
4
5
6
PQRS
TUV
7{
DISPLAY
K
9
8
SPACE
WXYZ
L CLEAR
0
REC SPEED REV
PL AY
TOP MENU MENU/LIST RETURN
FWD
ENTER
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
B
B
h
Bx1.3/0.8
K
REC/OTR
{
C
g
18 min
SP (2H)
36 min
LP (4H)
72 min
EP (6H)
108 min
SLP (8H)
144 min
(good)
SP (2H)
120 min
12cm Disc LP (4H)
EP (6H)
240 min
PROG.
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
7
TUV
WXYZ
REPEAT
ENTER
Recording times appear on the TV screen
(30 minutes to 8 hours).
Recording will start.
K
B
L
REV
PL AY
B
h
PAUSE
H
REC/OTR
FWD
g
I
0:30
SKIP
F
G
STOP
CM SKIP
POWER
B
h
TIMER
PROG.
PAUSE
H
F
.@/:
REC/OTR
ABC
DEF
STOP
1
2
3
C
0:30
GHI
JKL
(Normal Recording) 1:00
MNO
8:00
9
ZOOM
CLEAR
SETUP
.@/:
RETURN
ABC
ENTER
CM SKIP
7:30
6
WXYZ
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
--:--
-----
1
5.
---
6.
-----
After all recordings, finalize your disc.
Bx1.3/0.8
SKIP
PAUSE
SKIP
H
F
G
B
MNO
5A
CH
SPACE
CLEAR
TIMER
CM SKIP
TIMER
0
ABC
ABC
2SETUP
OPEN/CLOSE
JKL K
5ENTER
A
L
TUV
PQRS
DEF
7
3
2 REC SPEED
Playable
CM SKIP
CHANNEL
REC SPEED
REV
FWD
STOP
PLAY
POWER
REC/OTR
S-VIDEO
VIDEO
REPEAT
SETUP
OPEN/CLOSE
DEF
L AUDIO R
C
6
WXYZ
CH
B
REPEAT
A
CH
6
5
SPACE
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
GHI
2.
---
3.
---
4.
---
5.
---
6.
---
7.
---
8.
---
1
0
SKIP
PAUSE
TIMER
End
CH
Speed
ZOOM
PROG.
GHI
{
H
F
RETURN
TOP
MENU MENU/LIST
--:-L1
Start
12:57AM
4
STOP
ABC
DEF
PQRS
C
REC SPEED
REC/OTR
.@/:
1
2
JKL
GHI
K
7 3
MNO
DISPLAY
Move
{ to next
POWER
4
6
5 Bx1.3/0.8
2 K 3
OPEN/CLOSE
SKIP
JKL
MNO
G
ENTER
A
5
L 6
CM SKIP
TUV
WXYZ
REV
PL AY
8
9
CH
SPACE
B
SKIP
CLEAR
PAUSE
B
h
0
TIMER
H
F
L WXYZ ZOOM
PROG.
TUV TOP MENU
REPEAT RETURN
MENU/LIST
STOP
REC/OTR
PQRS
2.
---
3.
---
4.
---
5.
---
6.
---
7.
---
Start
12:57AM
1
0
SKIP
PAUSE
GHI F
End
CH H Speed
RETURN
TOP MENU MENU/LIST
1:57AM CH 8
4{
STOP
REC/OTR
PQRSC
Bx1.3/0.8
g
B
2.
---
3.
---
4.
-----
End
CH
8
1H
CM SKIP
TUV L WXYZ
REPEAT
6
5
g
FWD
g
SETUP
SKIP
G
ENTER
CM SKIP
C
SKIPK
G
F
{
STOP
TIMER
ZOOM
PROG.
OPEN/CLOSE
B
CM SKIP
L
ABC
2
3
GHI
JKL
MNO
DEF
CH
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
PL AY
REV
Bx1.3/0.8
SKIP
PAUSE
SKIP
H
F
G
STOP
CM SKIP
h
REC/OTR
Set the Timer Program.
DVD player
Not Playable
{
B
L
REC SPEED
Bx1.3/0.8
REC/OTR
REV
PL AY
h
B
FWD
1
2
GHI
JKL
4
5
PQRS
TUV
B
DEF
L
PL AY
h
B
FWD
g
3
Bx1.3/0.8
SKIP
PAUSE
CH
H
F
G
STOP
CM SKIP
MNO
6
REC/OTR
REPEAT
WXYZ
SKIP
C
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
0
K
B
When pressing L at the current date,
Timer Recording mode will change as follows:
e.g. January 1st at present
PL AY
REC SPEED
REV
Bx1.3/0.8
SKIP
FWD
g
B
h
PAUSE
H
REC/OTR
SKIP
F
G
STOP
CM SKIP
C
JAN/01
L
Daily
L
MON-SAT
L
MON-FRI
L
SAT
L
FRI
SUN
L
JAN/31
Set the Timer Standby mode
Turn the unit off.
POWER
TIMER
ZOOM
PROG.
.@/:
ABC
DEF
1
2
3
GHI
JKL
MNO
OPEN/CLOSE
A
CH
4
5
6
PQRS
TUV
WXYZ
7
8
9
DISPLAY
SPACE
CLEAR
SETUP
TOP MENU MENU/LIST RETURN
ENTER
REPEAT
0
B
FWD
g
C
REPEAT
K
ABC
REV
indicator will appear on the front panel display.
REC SPEED
A
---
7. .@/:--8. 1 ---
.@/:
OPEN/CLOSE
PROG.
REC SPEEDA
G
ENTER
A
CM SKIP
CH
B
PAUSE
CH H Speed
1:57AM
REC/OTR
TIMER
ZOOM
g
C
POWER
5.
SKIP
Bx1.3/0.8
Start
K
{
POWER
SETUP
SKIP
OPEN/CLOSE
SKIPK
JKL G
MNO
ENTER
{
Move
to next
12:57AM
Speed
L
REPEAT
FWD
3
2
B
CH
L
BCH
C
7
8
REC SPEED
REV
PL9AY
K
B
h
DISPLAY
SPACE
CLEAR
B
0
Bx1.3/0.8 SKIP
PAUSE
L
H
F
RETURN
TOP MENU MENU/LIST
---
End
9
8
K
{
B
L
REC SPEED
REV
PL AY
h
B
Bx1.3/0.8 SKIP
Hints for DVD Recording
H
PAUSE
FWD
g
SKIP
F
G
STOP
CM SKIP
REC/OTR
I Formatting is not needed
when inserting a blank
disc. UNIT AUTOMATICALLY PREPARES THE
DISC FOR RECORDING.
I For playback on other DVD players, be sure to
record in Video mode and to finalize the disc once
recording is finished. OTHER PLAYER MUST
PLAY BACK DVD-R or DVD-RW.
C
0
This Unit
OPEN/CLOSE
CLEAR
{
3
MNO
Start
A
ENTER
REV
PL AY
FWD
K
DISPLAY
SPACE
CLEAR
SETUP
g
B
hCH
JKL
MNO
0B
OPEN/CLOSE
POWER6
5 Bx1.3/0.8
SKIP
PAUSE
SKIP
TIMER
RETURN
ENTER
TOP
MENU MENU/LIST
L
ZOOM
PROG.
H
G
F
TUV
WXYZ
REPEAT
A
8 REC/OTR
CM SKIP
STOP
REV
PL9AY
FWD
ABC
.@/:
DEF
C
g
B
h
SPACE
CLEAR
SETUP
PQRS
Date
1. JAN/01
6.
g
CH
6
{
Move
to next
4
Date
FWD
OPEN/CLOSE
STOP
JKL
9
0
DISPLAY
Timer Programming POWER
Bx1.3/0.8
1. JAN/01
B
PL AY
---
8
h
L
Stop the recording.
REV
8.
A
7 end time.
REC SPEED
Set start and
8.
After recording, you must finalize the disc in order to play on other
units.
REC SPEED
FWD
SPACE
g
STOP
4.
---
---
7 3
ZOOM
PROG.
G
RETURN
T--:-OP MENU MENU/LIST
4{
L1
3.
7.
---
7.
WXYZ
F
.@/:C
8.
---
6.
TUV
GHI
EndPAUSE CH SKIP Speed
---
5.
6
5
ZOOM
PROG.
TUV TOP MENU
WXYZ MENU/LIST
REPEAT RETURN
DISPLAY
B
POWER
Timer Programming
K
{
H
4.
3
PQRS
DEF
.@/: 9
1CLEAR
---
DEF
B
8
---
3.
PROG.
4
DISPLAY
MNO
POWER
2.
ABC
SPEED REV REC/OTR
PL AY
FWD
STOP
Select theRECrecording
speed.
REPEAT
0
JKL
OPEN/CLOSE
---
ZOOM
GHI
PROG.
2
PL AY
REV
--- REC/OTR
1. JAN/01
CH
5
TUV
1
TIMER
1
2
OPEN/CLOSE
TIMER
REPEAT
PQRS
h
Timer Programming
.@/:
h
When the unit reaches the specified time,
the unit will be turned off automatically.
G
7
REC/OTR
8
SPACE
Timer Programming
SKIP
A
4
h
7
DISPLAY
DateBx1.3/0.8
Start SKIP
POWER
1.
7SPEED REV
8
PL9AY
FWD
Select theREC
channel
number
to record.
ABC
.@/:
DEF
DISPLAY
SPACE
CLEAR
SETUP
C
FWD
g
OPEN/CLOSE
PQRS
POWER
WXYZ
TUV
Date
PL AY
REV
ZOOM
SKIP
Bx1.3/0.8
CH
PQRS
REC SPEED
CH
TOP MENU MENU/LIST RETURN
SKIP
6
TOP MENU MENU/LIST
2.
SETUP
Bx1.3/0.8
3
MNO
5
1. JAN/01
CLEAR
REC SPEED
2
JKL
4
0
(poor)
SEP
(10H) 600 min
A
Date
DEF
1
GHI
7
Set the date.
0
{
ABC
A
GHI
9
8
PROG.
L
Press repeatedly to select desired recording time.
SPACE
ZOOM
K4
480 min
OPEN/CLOSE
3
MNO
4
OPEN/CLOSE
TIMER
{
360 min
SLP (8H)
TIMER
ZOOM
POWER
.@/:
60 min
POWER
2
JKL
Timer Programming
(good)
L
REC SPEED
DEF
Timer Programming list appears.
DISPLAY
XP (1H)
SETUP
Record on DVD disc.
PROG.
ABC
TUV
PQRS
WXYZ
REPEAT
Select any blank line with [K / L] and press
[ENTER].
7
9
8
(poor)
REPEAT
B
XP (1H)
TIMER
ZOOM
GHI
Recording Recording Video/Sound
Quality
speed
time
SEP (10H) 180 min
DISPLAY
REPEAT
OPEN/CLOSE
Press [TIMER PROG.].
How to select the recording speed:
L
PL AY
POWER
1
B
h
Timer Recording
.@/:
K
{
3 –2
• You can set up to 8 programs (once, daily or weekly).
• Be sure to set the clock before starting a timer programming.
REPEAT
Select the recording
speed.
DISPLAY
DVD Recording
A
Timer Recording
is now set.
g
SKIP
PAUSE
H
F
G
STOP
CM SKIP
SKIP
1VMN22667 / E7A01UD_QG ★★★★★
C
DVR91DG_E7A01UD_QG_EN.indd 2
2006/02/08 13:42:14

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project