Sminn BOX M 440 Instruction Manual
Advertisement
Advertisement
USAGE RESTRICTIONS
Operation is not guaranteed when installed in different equipment than the specified one.
THE USAGE INSTRUCTIONS OF THIS DEVICE SHALL BE HANDED TO THE USER, WHO WILL
HAVE THEM IN THEIR POSSESSION. IF THEY ARE MISLAID, THE USER CAN ASK FOR A COPY
OR DOWNLOAD IT DIRECTLY FROM WWW.SMINN.COM
The manufacturer reserves the right to change the specifications of these systems as well as this manual without prior warning. The equipment must be manipulated only by specialized and/or skilled personnel.
WARRANTY
This product has undergone a complete TEST during its manufacturing process that guarantees its reliability and proper operation. The manufacturer provides 24 months of warranty to the product from the date printed in the product and against any anomaly that it may present in its appearance or operation.
Any damage caused by third parties, natural causes (flooding, fire, lightning, etc), arising from improper handling or installation, vandalism or any other cause non attributable to the manufacturer will void the warranty. The warranty only covers repairs or replacement of the damaged device.
Any expenses derived from assembling, travelling, transport, natural wear of parts, etc., and, in general, any expenses that are not part of the repairs or replacement of the damaged element of the system are excluded.
The installer/provider will ask the manufacturer for a RMA number or authorization for transport of the system in warranty. Without this previous requisite, the manufacturer will not be able neither to process nor provide warranty service.
WARNING
This product must be used in installations which has been conceived for, considering any other as improper use. The packaging must not be dumped in the environment. Keep products, packaging, wrapping, documentation, etc., out of the reach of children. Follow the current local, national or European regulations. The information contained in this document may have some mistakes that will be corrected in future editions. The manufacturer reserves the right to modify the contents of this document or the product without any prior warning.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
In accordance with the European Directive 2002/96/EC about waste electrical and electronic equipment (WEEE), the presence of this symbol (see symbol at the bottom of this text) in the product or in the packaging, means that this article shall not be disposed in local non-classified waste streams. It is the user’s responsibility to dispose this product taking it to a collection point designed for waste recycling of electrical and electronic devices. The separate collection of this product helps optimize the waste sorting and recycling of any recyclable material and also decreases the impact on health and the environment. For more information about the correct wasting of this product, please contact the local authority or the distributor where you acquired this product.
BOX M 440
RECEIVER + BASE STATION
INSTRUCTION MANUAL
CE DECLARATION OF CONFORMITY
The company ELSON SISTEMAS, S.L
Pol. Torrelarragoiti, P6-A3-1ª
48170 Zamudio - Bizkaia (SPAIN)
Declares
The product: Receiver + Base Station BXM-440
ELSON ELECTRÓNICA, S.A.
Manufactures by
Under the trademark:
For use in: enviroments.
SMINN
Residential, Commercial or light industry
This device meets the provisions as long as its usage is compilant to what was envisaged, having applied the following regulations:
Telecommunications:
Electromagnetic compatibility:
Low Voltage
EN 300 220-1 v1.3.1 (2000-09)
EN 300 220-1 v1.1.1 (2000-09)
EN 301489-1 v1.3.1 (2001-09)
EN 301489-3 v1.3.1 (2001-11)
EN 60730-1:2000
2011-03-30 Zamudio
Jose Miguel Blanco Perez
Chief Technical Officer innovative in electronics
T. 944 525 120 www. sminn.com
Pol. Torrelarragoiti, P6 A3 - 1ª
48170 Zamudio Bizkaia innovative in electronics
DESCRIPTION
SMINN's receivers + base station controllers are developed with state-of-the-art electronic devices. They provide a high degree of operating reliability and security.Equipped with a solid communication bus RS 485 that allows more mounting versatility and makes them more immune to interference.
They are designed to provide the activation and movement order to SMINN motor controllers, alarms, access control and home automation systems, etc.
These devices are built using high quality materials and components and the latest technology. They are devices that observe the current regulations for usage in residential, commercial and light industry environments.
OPERATION
.
When a code from a SMINN key-tag or emitter is received, the receiver + base station controller checks if it is already registered in the memory. If it is registered and not blocked, the relay will
.
activate.
ERASE MEMORY
.
The memory can only be erased using SMINN's programming console and knowing its PIN,
.
avoiding accidental or malicious erasures.
.
BLOCKING A CODE IN THE MEMORY
A transmitter code cannot be simply erased from the memory, but it can be blocked so it won't work anymore. Blocking codes in the memory can only be done using a SMINN
..
programming console and knowing its PIN.
.
MANUAL PROGRAMMING
Step by step instructions on how to program a receiver are detailed next. The first code must be stored following all these steps.
TRANSMITTERS
1. Press and hold the MEMO RADIO PROG button (Fig.1 Item 4).
2. Press the button of the transmitter channel we want to learn that will be assigned to the corresponding relay. When receiving the code and channel sent by the transmitter, the receiver will store it in its memory and beep twice as a validation signal.
3. Release the programming button of the receiver.
Repeat this process with as many transmitter codes as you want to manually register in the memory, using the same channel as with the first transmitter. Pressing any other channel will not have any effect.
TAGS
1. Press and hold the MEMO KEY-TAG PROG button (Fig.1 Item 14).
2. Position the TAG to learn near the reader. When receiving the code sent by the TAG, the receiver will store it in its memory and beep twice as a validation signal.
3. Repeat this process for all the TAGS to learn.
4. Release the programming button of the receiver.
Holding a KEY-TAG near the reader for 10 sec. opens the memory enabling the user to learn new TAGS just by positioning them near the reader one by one without pressing the PROG button.
REGISTRATION VIA RADIO
Depending on the level of security configured in the receiver's memory it is possible to register transmitter codes via radio.
Security level 1 (Basic).- Transmitter can be programmed in invitation mode knowing the PIN
(the certified number of the installation) using a SMINN programming console. Invited transmitters are automatically registered by level 1 receivers.
Security level 2 (Intermediate).- Transmitters already in use can INVITE new transmitters that share the same PIN (the certified number of the installation).
Security level 3 (Advanced).- Emitters will be registered in the receiver manually. Radio-based registration is disabled.
CODE REPLACEMENT DUE TO LOSS
This function allows to replace a transmitter code stored in the receiver with a new one, be it due to loss or mislaying. The replacement of a transmitter code is only possible with a SMINN programming console. Knowing the PIN of the installation and the code number of the lost transmitter is required.
Note: This function is not available for Key Tags.
BACKUP COPY
Although the device is protected against power line disturbances and electrical surges, it is important to keep a backup of the memory card in case of breakdown or damages caused by external circumstances such as electric storms, theft, improper handling, etc.
INSTALLATION
.
SMINN's Base-Station controller is designed to be easily fixed on a wall using the supplied wall plugs and screws. Before connecting or operating the device, the power supply switch or differential shall be disconnected. Specialized and/or skilled personnel will do the installation, using properly protected cable of enough gauge. Take into account that devices permanently connected to the mains need to have an accessible connection device
(i.e. a magnetothermic switch). The wiring should be done following the instructions printed in the serigraphy of the circuit board. Make sure that the memory is inserted and properly configured. After programming and verifying the equipment, close the case with the supplied top.
SMINN'S BASE STATION CONTROLLERS ARE EQUIPPED WITH A LED TO LET KNOW
IF THE DEVICE IS POWERED.
Note: Reinforced concrete, metallic components and/or any other receiving device reduce dramatically the radiofrequency signal, so installation close to these elements should be avoided.
WIRING
.
Wiring is easy using the terminal block for three circuits.
Readers are connected using just 4 wires on the terminals 3 to 6,
.
with two wires for power and two for the RS485 data BUS.
Terminal Function Note
1
2
3
4
5
6
7-8
9-10
11-12
13-14
Power
Positive (+)
Negative (-)
Line (A)
Line (B)
NO contacts
NO contacts
NO contacts
NO contacts
230V AC power input
Power output to readers/keypads
Apply to the BUS RS485 line
Cannal 1 relay
Cannal 2 relay
Cannal 3 relay
Cannal 4 relay
The RS485 BUS is used in Half / Duplex mode with two wires: A and B.
All elements of the BUS must have the same connection. A wires connected to A,
.
and B to B (they must not be exchanged).
TECHNICAL CHARACTERISTICS
BOX M 440
BOX M 480
BOX M 444
BOX M 484
RADIO
Sensibility
Radio
Encoding
Antenna
Min./Max. consumption at 12/24VDC
TAG
Type
Energy consumption
Comunication
Encryption
Wiring
Max. capacity of peripherals
Maximun distance
COMMON
Power suply
Code memorization
Memory expansion
Operation temp.
Dimensions
Watertight
433.92 MHz
868.3 MHz
433.92 MHz
868.3 MHz
230 VAC
230 VAC
12/24 VAC/DC
12/24 VAC/DC
< -115 dBm
Superheterodine
High security Cryptocode
Internal helicoidal
20mA / 80mA (without readers)
Read-write 125KHz
< 5W
BUS RS485 Half / Duplex
High security encryption
4 wire (recommended shielded cable CAT5)
2 RD125 readers + 2 KB120 keyboards
> 200m
230VAC (125VAC optional)
Plug-in memory of 250 codes
500 / 1000 / 2000
-20ºC / +85º C
182 x 145 x 65 mm (antenna not included)
Ip54 - (IP65 with cable glands)
Fig.1
Fig.2
GENERAL WIRING
L
230
VAC
N
15
14
13
12
11
10
9
COMPONENTS
1.
ON Led
2. RUN/Status/Error Leds
3. Radio Module
4. Radio PROG button
5. Radio memory card
6. Register card (optional)
7. Relays
+ -
B A
RD 125
1 2
3
6
7
8
4
5
12.
13.
14.
15.
8. Terminal strip
9. 230VAC power connector
10. Fuse 0.3A
11. Buzzer
Selector Switch
Transformer
Key-TAG memory card
Key-TAG programming button
Activation signals to control pannel
+ -
B A
RD 125
+ -
B A
KB 120
B
A
-
+

Public link updated
The public link to your chat has been updated.
Advertisement