Installation Note
Agilent Technologies
ESA Spectrum Analyzers and EMC Analyzers
Front Frame Assembly
Kit Number: E4401-60257 or E4401-60259
Part Number: E4401-90333 Supersedes: E4401-90308
Printed in USA September 2001
Notice.
The information contained in this document is subject to change without notice.
Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
© Copyright 2001 Agilent Technologies, Inc.
Introduction
Products Affected: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4401B ESA Spectrum Analyzer
E4402B ESA Spectrum Analyzer
E4403B ESA Spectrum Analyzer
E4404B ESA Spectrum Analyzer
E4405B ESA Spectrum Analyzer,
E4407B ESA Spectrum Analyzer
E4408B ESA Spectrum Analyzer
E4411B ESA Spectrum Analyzer
E7401A EMC Analyzer
E7402A EMC Analyzer
E7403A EMC Analyzer
E7404A EMC Analyzer
E7405A EMC Analyzer
Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . US00000000/US99999999
MY00000000/MY99999999
Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . all
To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Technologies Service Center
(X) Personnel Qualified by Agilent
(X) Customer
Estimated Installation Time:. . . . . . . . . . . . . . . . . . . . . . . 1.5 Hours
Installation Note E4401-90333 3
Model Identification and Connector Label Part Numbers
The model identification label and connector label were not shipped with new front frame kits. It is possible to re-use the existing labels. However, if one is damaged or the adhesive degrades, you can order one or both labels. The following table lists the part numbers for each of the labels depending on the model and option mix.
Model Number Option
E4408B
E4411B
E4411B
E7401A
E7402A
E7402A
E7403A
E7403A
E7404A
E7404A
E7405A
E7405A
E4401B
E4401B
E4402B
E4402B
E4403B
E4404B
E4404B
E4405B
E4405B
E4407B
E4407B
E4407B
Standard
Standard
1DP (75 ohm)
Standard
Standard
UKB
Standard
UKB
Standard
UKB
Standard
UKB
Standard
1DP (75 ohm)
Standard
UKB
Standard
Standard
UKB
Standard
UKB
Standard
UKB
AYZ
Model ID. Label
E4408-80003
E4411-80012
E4411-80013
E7401-80001
E7402-80001
E7402-80002
E7403-80001
E7403-80002
E7404-80001
E7404-80002
E7405-80001
E7405-80002
E4401-80027
E4401-80028
E4402-80002
E4403-80016
E4403-80008
E4404-80004
E4404-80008
E4405-80003
E4405-80006
E4407-80003
E4407-80006
E4407-80003
Connector Label
E4407-80001
E4401-80003
E4401-80002
E4401-80003
E4403-80002
E4403-80015
E4404-80001
E4404-80007
E4405-80001
E4405-80005
E4407-80001
E4407-80007
E4401-80003
E4401-80002
E4403-80002
E4403-80015
E4403-80002
E4404-80001
E4404-80007
E4405-80001
E4405-80005
E4407-80001
E4407-80007
E4407-80005
4 Installation Note E4401-90333
Kit Material Lists
Front Frame Kit (Standard), E4401-60257
Part Number
E4401-60257
E4401-60127
E4401-90333
Description
Frame
Lens/keypad
Installation note
Front Frame Kit (Option 060), E4401-60259
Part Number
E4401-60259
E4401-60256
E4401-90333
Description
Frame
Lens/keypad
Installation note
Installation Note E4401-90333 5
Installing the Lens Keypad
The display lens/keypad assembly will need to be installed into the front frame assembly.
1. Referring to Figure 1 , clean the inside of the lens
(1) to remove any fingerprints, lint, or dust.
CAUTION Avoid contaminating, by touching or cleaning, the black conductive pads (2) on the back of the keypad.
2. Remove the adhesive backing (3) from the front side of the lens/keypad assembly.
3. Position the lens/keypad assembly into the front frame as shown.
4. Inspect the 4 sides (4) of the lens/keypad to make sure the EMI gasket is properly positioned. Reseat it if necessary.
5. Press around the edges (5) of the lens/keypad to seat it into the front frame.
6. The front frame is ready for the next step in the assembly process.
Figure 1 Installing the Lens/Keypad Assembly
6 Installation Note E4401-90333
