Agilent 1680-Series
Logic Analyzers
Motherboard Upgrade
Assembly Guide
Agilent Technologies
Notices
© Agilent Technologies, Inc. 2004
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by
United States and international copyright laws.
Manual Part Number
01680-97013
Edition
First edition, November 2004
Printed in USA
Agilent Technologies, Inc.
1900 Garden of the Gods Road
Colorado Springs, CO 80907 USA agency regulation or contract clause. Use, duplication or disclosure of Software is subject to Agilent Technologies’ standard commercial license terms, and non-DOD
Departments and Agencies of the U.S. Government will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than
Limited Rights as defined in FAR 52.227-14
(June 1987) or DFAR 252.227-7015 (b)(2)
(November 1995), as applicable in any technical data.
Warranty
The material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. Should
Agilent and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control.
Technology Licenses
The hardware and/or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license.
Safety Notices
C A U T I O N
A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a
CAUTION notice until the indicated conditions are fully understood and met.
WA R N I N G
A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met.
Restricted Rights Legend
If software is for use in the performance of a U.S. Government prime contract or subcontract, Software is delivered and licensed as “Commercial computer software” as defined in DFAR 252.227-7014
(June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as “Restricted computer software” as defined in FAR
52.227-19 (June 1987) or any equivalent
Agilent 1680-Series Logic Analyzers Motherboard Upgrade
Assembly Guide
Upgrading a 1680-Series Logic
Analyzer’s Motherboard
Upgrade Kit Contents 4
Procedure 5
Agilent Technologies
3
4
Upgrading a 1680-Series Logic Analyzer’s Motherboard
Upgrade Kit Contents
The 01680-68720 1680-series logic analyzer motherboard upgrade kit contains the items shown in the following table.
Table 1
Part Number Description
01680-00203 Filler Panel
01680-61625
01680-61626
IDE Cable
Power Switch Cable
01680-68724
01680-83512
01680-87102
0380-4944
1680 Recovery CD Kit
Formatted Hard Disk Drive
Gasket-I/O
Hex Standoff
0515-0430
0960-2481
8160-1545
9010-0250
Screws
Motorola VP22 Motherboard
RFI Gasket
Microsoft Windows XP Professional Certificate of Authenticity
B3764-68714 16900/1680/1690 Software CD Kit
1
1
1
1
1
1
Qty
1
2
1
2
1
1
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
Procedure
1 Unplug the power cord from the back of the logic analyzer.
2 Unplug the keyboard and the mouse from the back of the logic analyzer.
Assembly Guide 5
Upgrading a 1680-Series Logic Analyzer’s Motherboard
3 Remove the five screws securing the logic analyzer cables.
4 Unplug the logic analyzer cables.
6 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
5 Remove the screws at each end of the handle; then, remove the handle.
6 Remove the screw from the center of each of the four feet, and remove the feet.
7
Upgrading a 1680-Series Logic Analyzer’s Motherboard
7 Remove all the screws which secure the case cover.
8 Slide the case off backwards.
It will be tight in order to maintain and EMI seal.
Please don't put great pressure on the acquisition card.
8 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
9 Unplug the IEEE 1394 (firewire) cable from the IEEE 1394 PCI card.
10 Remove all of the PCI cards.
Disconnect the display cable from the video card.
9
Upgrading a 1680-Series Logic Analyzer’s Motherboard
11 Remove the video PCI card.
12 Remove the LAN card.
10 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
13 Remove the IEEE 1394 PCI card.
14 Disconnect the CD cable from CD-IN LGGR of motherboard.
11
Upgrading a 1680-Series Logic Analyzer’s Motherboard
15 Disconnect cable from CD, P2 power.
16 Disconnect cable from CD, P3 Audio RGGL.
12 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
17 Disconnect cable from CD, P1 IDE.
18 Remove the five screws holding the CD in the back panel.
13
Upgrading a 1680-Series Logic Analyzer’s Motherboard
19 Lift the CD tray out of the unit.
20 Remove the four screws holding the HDD to the side on the unit.
14 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
21 Lift the HDD out of the unit and unplug the power cable.
22 Remove the IDE cable from the HDD.
15
Upgrading a 1680-Series Logic Analyzer’s Motherboard
23 Remove the power connector to the motherboard, CN1.
24 Remove the CD cable from IDE1 on the motherboard.
16 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
25 Remove the HDD cable from IDE2 on the motherboard.
26 Remove the power switch connector from J1 on the motherboard and remove the other end as well. Set this cable aside as a new power switch cable is supplied.
The new power switch cable has the wires reversed.
17
Upgrading a 1680-Series Logic Analyzer’s Motherboard
27 Remove the floppy drive cable from FDD1 on the motherboard.
28 Remove the three screws securing the back filler plate to the back panel.
18 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
29 Remove the screws securing the motherboard to the standoffs mounted on the floor of the unit. (There are 7 screws if you are upgrading from a Tyan motherboard, or 6 screws if upgrading from a Radisys motherboard.)
30 Lift the motherboard up and out of the unit.
19
Upgrading a 1680-Series Logic Analyzer’s Motherboard
31 Remove six of the screws with threaded heads on either side of the connectors on the back of the old motherboard for use on the new motherboard.
32 Fit the new filler panel to the back of the new motherboard.
20 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
33 Install the six screws removed from the back of the old motherboard on the new motherboard to hold the filler panel in place.
34 Cut a piece of the short EMI gasket to length to cover the top half of the filler plate.
21
Upgrading a 1680-Series Logic Analyzer’s Motherboard
35 Peel off the protective covering of the self adhesive on the EMI gasket.
36 Press the EMI gasket firmly onto the filler plate.
22 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
37 Repeat this process with the other short EMI gasket for the top left side of the filler plate and install the longer EMI gasket across the bottom of the filler plate.
38 Install the new standoff on the floor of the unit as indicated.
23
Upgrading a 1680-Series Logic Analyzer’s Motherboard
39 Tilt the new motherboard into the unit and place it on the floor.
40 Install the three screws securing the filler plate to the back panel. Leave slightly loose until all the other screws are in place and then tighten all of them.
24 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
41 Install eight screws to secure the new motherboard to the floor of the unit.
42 Connect the floppy drive cable to FDD on the motherboard.
25
Upgrading a 1680-Series Logic Analyzer’s Motherboard
43 Connect the power switch cable to proper pins of CN14.
Proper pins are the back row when viewed from the top when the front is toward you, the 4th and 5th pins.
000XX00000
0000000000 front of unit
26 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
44 Reinstall the CD tray with five screws to the back of the unit.
45 Reconnect the motherboard power supply cable in CN11.
27
Upgrading a 1680-Series Logic Analyzer’s Motherboard
46 Reconnect the CD cable to IDE1 of the motherboard.
47 Reconnect the HDD cable to IDE2 of the motherboard.
Use the newly supplied one because it is longer than the original.
28 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
48 Reconnect the other end of the HDD cable to the new 80G hard drive.
49 Reconnect the power cable to the new 80G hard drive.
29
Upgrading a 1680-Series Logic Analyzer’s Motherboard
50 Mount the new 80G hard drive to the side of the unit using the original four screws.
51 Reconnect the CD cable in the CD , P1 IDE.
30 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
52 Reconnect the Red/Black/White/Black cable in the CD-IN LGGR of the motherboard.
53 Reconnect the other end of the Red/Black/White/Black in the CD, P3 Audio
RGGL (lower connector).
31
Upgrading a 1680-Series Logic Analyzer’s Motherboard
54 Reconnect the Red/Black cable in the P2 Power (upper connector) of the
CD.
55 Reinstall the IEEE 1394 PCI card in the first PCI slot (nearest the CD tray).
32 Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
56 Install a filler panel opposite the second PCI slot.
The LAN PCI card is no longer required because the new motherboard has builtin 10/100 Ethernet.
Assembly Guide 33
Upgrading a 1680-Series Logic Analyzer’s Motherboard
57 Route the IEEE 1394 (firewire) cable through the cable stays as it was formerly, and include the Red/Black CD power cable as well. Plug the IEEE
1394 (firewire) cable into the top of the IEEE 1394 (firewire) PCI card.
Be certain that it seats fully and locks in place.
58 Reinstall the PCI slot video card in the next PCI slot.
34 Assembly Guide
Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
59 Connect the video cable from the front panel to the connector on the PCI video card.
60 Slide the case back onto the unit from the rear.
Be certain that it has fully seated in the front bezel.
35
Upgrading a 1680-Series Logic Analyzer’s Motherboard
61 Secure the case by reinstalling all the screws on the back.
62 Reinstall the four feet.
36 Assembly Guide
Assembly Guide
63 Reinstall the handle.
Upgrading a 1680-Series Logic Analyzer’s Motherboard
64 Plug the analyzer cables back in.
37
Upgrading a 1680-Series Logic Analyzer’s Motherboard
65 Secure the analyzer cables by reinstalling the five screws which hold them.
66 Plug in the keyboard and mouse.
38 Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
67 Plug the power cord in and start the unit.
N O T E
68 If the unit appears to hang after either “The volume is clean. Windows has finished checking the disk”, or “please wait while Windows starts”, then please note the following:
The Tyan motherboard only had one video device from which to choose; it was the PCI slot video card. There was an internal output from this video card which drove the 1680-series logic analyzer flat panel display, and there was an external monitor output on the back of the PCI video card. Both the internal output and the external monitor output on the back of the PCI video card always displayed the same data.
However, the Motorola VP22 motherboard has this same PCI video card plus a external monitor output on the motherboard.
Before concluding that the motherboard is failing to boot, check the external monitor output, and be certain that the output is not merely being sent to that output instead of the flat panel display. This is likely.
You may need to connect an external monitor while you are booting Windows XP on this motherboard for the first time in order to get through all the required inputs.
Assembly Guide 39
Upgrading a 1680-Series Logic Analyzer’s Motherboard
After accepting the End User License and answering all the other questions in the Windows XP welcome screens, load the Agilent Logic Analyzer application version 3.00.
After loading the Agilent Logic Analyzer application version 3.00, you will be able to choose between the external monitor output and the internal flat panel display as the main display device.
To set the LCD as the display device: a Right-click on the desktop and choose Properties .
b c
In the Display Properties dialog, select the Settings tab; then, choose a screen resolution of 800 by 600 pixels and select the Medium (16 bit) color quality.
Click Advanced ; in the Display Device tab, select CHIPS -> LCD. You will also need to Select monitor "2" and UNCHECK "Extend my Windows desktop onto this monitor"; then, select "1" and apply.
d e
Click OK to close the dialogs.
Reboot.
69 Start the Agilent Logic Analyzer application, and choose Help>Self Test...
from the main menu to run the self tests.
40 Assembly Guide
Upgrading a 1680-Series Logic Analyzer’s Motherboard
Assembly Guide 41
Upgrading a 1680-Series Logic Analyzer’s Motherboard
42 Assembly Guide
www.agilent.com
In This Book
Agilent Technologies, Inc. 2004
Printed in Malaysia 11/04
First edition, November 2004
*01680-97013*
*01680-97013*
01680-97013
Agilent Technologies
