advertisement
HIGHlite Laser 3D Series
27
Super High Brightness Digital Video Projector
超高亮度数字视频投影仪
重要信息
Rev B August 2014
114-914B
Important Information
Digital Projection
Digital Projection Limited
Greenside Way, Middleton
Manchester M24 1XX, UK
Registered in England No. 2207264
Registered Office: as above
Tel
Fax
(+44) 161 947 3300
(+44) 161 684 7674 [email protected] [email protected]
www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115
Kennesaw, GA 30144, USA
Tel
Fax
(+1) 770 420 1350
(+1) 770 420 1360 [email protected] www.digitalprojection.com
Digital Projection HIGHlite Laser 3D Series
Digital Projection China
中国 北京市 朝阳区 芍药居北里
101号
世奥国际中心
A座2006室(100029)
Rm A2006
ShaoYaoJu 101 North Lane
Shi Ao International Center
Chaoyang District
Beijing 100029, PR CHINA
Tel
Fax
(+86) 10 84888566
(+86) 10 84888566-805 [email protected] www.dp-china.com.cn
Digital Projection Asia
16 New Industrial Road
#02-10 Hudson Technocentre
Singapore 536204
Tel
Fax
(+65) 6284-1138
(+65) 6284-1238
Page 2 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
Super High Brightness Digital Video Projector
Important Information
Contents
Symbols used in the User Manual
...............................................................................................4
Electrical and physical specifications
........................................................................................5
Laser precautions
Product labels
Location of laser aperture
Interlock switches
Lens hoods
General precautions
Installation precautions
Operation and configuration precautions
...............................................................................12
Compliance with international standards
...............................................................................12
European Waste Electrical and Electronic Equipment (WEEE) Directive ..............................12
Basic Operation Instructions
Control Panel Reference
Remote Control Reference
Full information about operating, connecting and setting up the projector can be found in the User
Manual, located on the CD.
Rev B August 2014 Page 3
Important Information
Digital Projection HIGHlite Laser 3D Series
Symbols used in the User Manual
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Specifications are subject to change without notice.
Page 4 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
Electrical and physical specifications
Mains Voltage
Operating Temperature
Storage Temperature
Operating Humidity
Weight
Power Consumption
Thermal Dissipation
Laser precautions
200-240 VAC
50-60 Hz (single phase)
0°C to 35°C
-20°C to 60°C
20% to 90% non-condensing
46.5 kg (102.5 lb) without lens
1600 W
5027 BTU/hr
CLASS 3R LASER PRODUCT
This Laser Product is designated as Class 3R during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow laser light to be directed or reflected toward other people or reflective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included instructions are not followed.
Caution – use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Class 2 range. Class 3R laser product, per IEC 60825-1, has limited risk of laser hazard and is safe for non-intrabeam viewing. It is recommended to keep the audience 100 cm away from the exit plane of the lens hood and reduce the laser hazard to a much safer class 2.
Non-laser emission. There remains non-laser emission from the projection lens. This portion of emission has been tested per IEC/EN 62471 to be Risk Group 1 (Low Risk).
Laser Parameters:
Wavelength
Laser Power for classification
Total internal power
Apparent Source Size
Divergence
Mode of operation
Modulation, due to frame rate
445 nm - 470 nm
< 330 mW
> 35 W
> 10 mm at lens stop
1 Radian to 100 mRadian
CW
23 - 192 Hz
Rev B August 2014 Page 5
Important Information
Digital Projection HIGHlite Laser 3D Series
Product labels
(
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机 )
Model/Modèle
(型號 / 型号):
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
Made in China.
(製造地:中國/製造地:中國)
HIGHlite Laser WUXGA 3D
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机
)
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
Made in China.
( 製造地:中國/製造地:中國 )
(1) this device may not cause harmful interference, and
( 型號 / 型号 ):
HIGHlite Laser WUXGA 3D
警告: 此為
A 級產品,在生活環境中,該產品可能會造成無線電干擾。
AC Input / Entrée CA
( 輸入 / 输入 )
:
200-240Vac 9.2A 50/60Hz
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
This device complies with part 15 of the FCC rules.
CAN ICES-3 (A)/NMB-3(A)
Complies with FDA performance standards for laser products except for
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
AVOID DIRECT EYE EXPOSURE
警告: 此為 A 級產品,在生活環境中,該產品可能會造成無線電干擾。
在這種情況下,可能需要用戶對干擾採取切實可行的措施。
S/N: XXXXXXXXXXXX
1
Caution : Do not open the cover. No user-serviceable parts inside
Manufacturer’s ID Label and
Explanatory Label
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
2
Certification Statement Label
3
CAUTION – CLASS 4 LASER LIGHT WHEN OPEN
AVOID EYE OR SKIN EXPOSURE TO
CLASS 3R LASER PRODUCT
455-470nm <330mW
Protective Housing Label
3264601800
XXXX XXXX
4
Hazard Warning Symbol and
Aperture Label
Page 6 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机 )
Model/Modèle
(型號 / 型号): HIGHlite Laser WUXGA 3D
AC Input / Entrée CA (輸入 / 输入): 200-240Vac 8A 50/60Hz
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
CAN ICES-3 (A)/NMB-3(A)
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
interne réparable par l’utilisateur.
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <330mW
CLASSIFIED IEC/EN 60825-1 2007
S/N: XXXXXXXXXXXX
Code39 of serial no.
Label locations
5
6
3
4
1
2
7
Location of Manufacturer’s ID
Label, Certification Statement
Label and Explanatory Label on the body of the projector
Manufacturer’s ID Label
(manufacturer’s name, address and projector model)
Certification Statement Label
Explanatory Label
Serial number
Protective Housing Label
(under the top cover and only visible to service personnel)
Location of Hazard Warning
Symbol and Aperture Label on the body of the projector
128.5
10mm
(
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机 )
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
Made in China.
(製造地:中國/製造地:中國)
Model/Modèle
(型號 / 型号): HIGHlite Laser WUXGA 3D
AC Input / Entrée CA (輸入 / 输入): 200-240Vac 8A 50/60Hz
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
CAN ICES-3 (A)/NMB-3(A)
(2) this device must accept any interference received,
including interference that may cause undesired operation.
警告: 此為
A 級產品,在生活環境中,該產品可能會造成無線電干擾。
在這種情況下,可能需要用戶對干擾採取切實可行的措施。
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
interne réparable par l’utilisateur.
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <330mW
CLASSIFIED IEC/EN 60825-1 2007
S/N: XXXXXXXXXXXX
Code39 of serial no.
3264601800
XXXX XXXX
Important Information
1
2
3
4
5
6
7
Rev B August 2014 Page 7
Important Information
Location of laser aperture
The laser aperture is located as indicated below.
Digital Projection HIGHlite Laser 3D Series
1
Laser aperture
1
Interlock switches
Five interlock switches installed at the main frame, inside the cover, will power-off the system individually when activated.
1 2
3
1
2
3
4
4
Will be activated when the top cover is removed.
Will be activated when the side cover is removed.
x2. Will be activated when the lens hood is removed.
Will be activated when the projection lens is removed.
Page 8 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Lens hoods
There are two types of lens hood, short and long.
Important Information
Projector with short lens hood fitted
The short lens hood is used with the following lenses:
Throw ratios
0.77 : 1 fixed lens
1.16 : 1 fixed lens
1.45 - 1.74 : 1 zoom lens
1.74 - 2.17 : 1 zoom lens
2.17 - 2.90 : 1 zoom lens
2.90 - 4.34 : 1 zoom lens
Part number
110-808
110-809
110-803
112-878
113-852
110-806
Projector with long lens hood fitted
The long lens hood must be used with the following long throw lens:
Throw ratios
4.34 - 6.76 : 1 zoom lens
Part number
110-807
Do not use the short lens hood with the long throw lens.
Rev B August 2014 Page 9
Important Information
Digital Projection HIGHlite Laser 3D Series
General precautions
The unit is never to be operated if the unit is defective or the cover or seal is damaged.
No maintenance allowed by end user.
Do not open the cabinet. There are no user serviceable parts inside.
No service is allowed except by authorized personnel.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling into the projector.
If this does happen, switch off immediately, and have the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power cable.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could cause a fire
Always allow the projector to cool for 5 minutes before disconnecting the power or moving the projector.
Never use strong detergents or solvents such as alcohol or thinners to clean the projector and lens.
Page 10 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar connectors may have a dangerously high voltage source.
The projector must be installed only by suitably qualified personnel, in accordance with local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the ventilation outlets and any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by its operational heat, for instance, polystyrene ceiling tiles, curtains etc.
Place the projector in a dry area away from sources of dust, moisture, steam, smoke, sunlight or heat.
The projector is heavy. Use safe handling techniques when lifting the projector.
Do not drop or knock the projector.
Before installation, make sure that the surface, ceiling or rigging that is to support the projector is capable of supporting the combined weight of the projector and lens.
When stacking projectors, the stack MUST be vertical, to ensure that the stresses are distributed to all four chassis corners.
Do not stack more than 3 projectors.
Do not place heavy objects on top of the projector chassis. Only the chassis corners and the optional rigging frame are capable of withstanding the weight of another projector.
Backup safety chains or wires should always be used with ceiling mount installations.
The projector can be operated in numerous positions.
The only non-workable angle is in portrait mode with inputs facing upward, as shown in the diagram:
30°
1
360°
2
1
2
Non-workable angle
Workable angles
Rev B August 2014
330°
Roll
2
Pitch
Page 11
Important Information
Digital Projection HIGHlite Laser 3D Series
Operation and configuration precautions
Do not make changes to the networking configuration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original settings, and any changes you have made.
Software update should NOT be carried out except by, or with the supervision of, Digital
Projection Service personnel.
Compliance with international standards
RF Interference
FCC
The Federal Communications Commission does not allow any modifications or changes to the unit
EXCEPT those specified by Digital Projection in this manual. Failure to comply with this government regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference.
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 48 dB (A) according to ISO 3744 or ISO 7779.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic
Equipment. Our products are designed with reuse, recycling and recovery of all components in mind. To this end, at end of life, your projector may be returned to Digital Projection Ltd or its agent so that the environmental impact can be minimised.
Page 12 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Basic Operation Instructions
Positioning the screen and projector
Important Information
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the fixing holes for ceiling mounting.
1
2
2
2
1
1
2
2
2
1
1
2
Four adjustable feet
Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into the body of the projector.
Rev B August 2014 Page 13
Important Information
Connecting the power supply
Digital Projection HIGHlite Laser 3D Series
Lift the cable lock up, push the mains connector in firmly and push the lock down to secure the cable.
1
AC mains inlet with cable lock
1
Use only the power cable provided.
Ensure that the power outlet includes a ground connection as this equipment MUST be earthed.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power cable.
Switching the projector on
1. Connect the power cable between the mains supply and the projector. (See Connecting the
power supply above.) Switch on at the switch next to the power connector.
Wait until the self-test has completed and the
STANDBY
indicator on the projector control panel shows blue. The system will be off and the projector will be in STANDBY mode.
The self-test is running when all the LEDs on the control panel are lit.
2. Press
ON
on the remote control or
STBY
on the control panel to switch the projector ON. The
ON
indicator on the control panel will show green, the system will light and the shutter will open.
Page 14 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Switching the projector off
Important Information
1. Press
OFF
on the remote control or
STBY
on the control panel. The
ON
indicator on the control panel will start flashing, the system will go out and the cooling fans will run for a short time until the projector enters STANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect the power cable from the projector.
Selecting an input signal
•
Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within two or three seconds.
•
If more than one signal is connected, then select the input you want to display:
•
Press one of the input buttons on the remote control, or
•
Open the On-screen display (OSD) by pressing
MENU
. Highlight
Input
from the main menu, press
ENTER/SELECT
and then select an input signal using the
UP
and
DOWN
arrow buttons. Press
ENTER/SELECT
to confirm your choice.
Selecting a test pattern
To display a test pattern:
•
Open the OSD by pressing
MENU
. Highlight
Test Patterns
from the main menu, then select a test pattern using the
LEFT
and
RIGHT
arrow buttons.
Rev B August 2014 Page 15
Important Information
Adjusting the lens
Digital Projection HIGHlite Laser 3D Series
The lens can be adjusted using the
Lens
menu, or using the
LENS
button on the remote control.
The
LENS
button opens the
Lens Control
setting, which adjusts zoom, focus and shift. The
Lens
menu gives you access to the
Lens Control
setting and the
Lens Center
command.
Lens Control
allows you to adjust
Zoom
,
Focus
and
Shift
using the arrow buttons. The setting operates in
Zoom/Focus Adjustment
and
Shift Adjustment
mode.
Press ENTER/SELECT to switch between modes as follows:
•
Zoom/Focus Adjustment
mode with the source image
•
Shift Adjustment
mode with the source image
•
Zoom/Focus Adjustment
mode with an alignment grid
•
Shift Adjustment
mode with an alignment grid
•
Zoom/Focus Adjustment
mode with an aspect test
•
Shift Adjustment
mode with an aspect test
•
Zoom/Focus Adjustment
mode with a screen layout pattern
•
Shift Adjustment
mode with a screen layout pattern
1.60:1 (16:10)
1.66:1
1.78:1 (16:9)
1.85:1
1.33:1 (4:3)
2.35:1
...
Page 16 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Adjusting the image
Important Information
•
This can be set from the
Setup
menu.
Highlight Projector Mode and choose from
Desktop Front
,
Ceiling Front
,
Desktop Rear
and
Ceiling Rear
.
•
This can be set from the
Geometry
menu.
•
Settings such as
Brightness,
Contrast
and
Gamma
can be set from the
Image
menu.
•
You can also set
Brightness
,
Contrast
or
Gamma
by pressing
BRIGHTNESS
,
CONTRAST
or
GAMMA
on the remote control.
Rev B August 2014 Page 17
Important Information
Digital Projection HIGHlite Laser 3D Series
Inserting a new lens
Before changing the lens, always make sure the projector is switched off and fully disconnected from its power supply.
When changing the lens, avoid using excessive force as this may damage the equipment.
Take care to preserve the original lens packaging and protective caps for future use.
The projector will not power on without the lens and lens hood fitted.
1. Insert the lens into the lens aperture, making sure that the plug on the zoom drive mechanism lines up with socket on the right of the lens aperture.
2. Rotate the lens clockwise until it clicks into place.
3. Secure the lens hood to the front of the projector with the screws.
Page 18 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
Removing the lens
Before changing the lens, always make sure the projector is switched off and fully disconnected from its power supply.
When changing the lens, avoid using excessive force as this may damage the equipment.
Take care to preserve the original lens packaging and protective caps for future use.
The projector will not power on without the lens and lens hood fitted.
1. Loosen the four screws securing the lens hood to the body of the projector.
Remove the lens hood.
2. Push down the lens holder tab.
3. Rotate the lens anti-clockwise.
4. Pull the lens forward to remove it from the lens aperture.
Rev B August 2014 Page 19
Important Information
Digital Projection HIGHlite Laser 3D Series
Changing the filters
Before changing the filters, always make sure the projector is switched off and fully disconnected from its power supply.
When changing the filters, avoid using excessive force as this may damage the equipment.
1. Loosen the screws holding the filter cover.
2. Remove the old filter.
Page 20 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
3. Insert the new filter. Make sure the air flow arrow on the side of the filter panel points toward the projector, as shown in the illustration.
4. Replace the filter cover and tighten the screws.
Rev B August 2014 Page 21
Important Information
Control Panel Reference
1
2
ON
ERROR
MENU
Digital Projection HIGHlite Laser 3D Series
6
3
4
ENTER
5
STANDBY
STBY INPUT
7
8
Page 22 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
2
1
ON indicator (green)
Behavior Meaning
Off The projector is switched off.
Flashing The projector is warming up or cooling down.
On The projector is switched on (NORMAL mode).
ERROR indicator (red)
Behavior
Flash three times, then pause
Flash four times, then pause
Flash five times, then pause
Meaning
Fan failure.
Over temperature.
Filter failure.
3
4
ENTER button
Confirm your choice when navigating the OSD.
Arrow buttons
Navigate the OSD, edit settings.
5
STANDBY indicator (blue)
Behavior Meaning
On The projector is in STANDBY mode.
6
MENU button
Access the projector OSD (on-screen display).
7
8
INPUT button
Select input source.
STANDBY button
Switch the projector on and off (in STANDBY mode)
Rev B August 2014 Page 23
Important Information
Remote Control Reference
1
2
Digital Projection HIGHlite Laser 3D Series
1
4
ON
|
POWER OFF
SOURCE
2
PIC
MUTE
3
5
10
3
ENTER
4
5
6
7
8
9
MENU
A
USER MEMORY
B
ASPECT
RATIO
C
SHARP
GAMMA
LENS
2D/3D
O-SCAN
C-TEMP
3D
SWAP
NR
TEST
3D
FORMAT
11
12
13
14
15
16
17
18
19
Page 24 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
Important Information
1
2
3
Power ON / OFF
Input selection
Select input source.
Navigation
Navigate through the menus with the arrows, confirm your choice with
ENTER
.
The
ENTER
button also accesses lens controls.
4
5
6
CONTRAST
Contrast
control, then adjust the value with
LEFT
and
RIGHT
.
7
GAMMA
Gamma
value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
8
9
10
11
ASPECT RATIO
...16:9, TheaterScope, 4:3, 4:3 Narrow, 16:10, 5:4, Source...
12
BRIGHTNESS
control, then adjust the value with
LEFT
and
RIGHT
.
13
SHARP
Sharpness
control, then adjust the value with
LEFT
and
RIGHT
.
14
O-SCAN
Overscan
mode:
...Off, Crop, Zoom...
15
NR
Noise Reduction
control, then adjust the value with
LEFT
and
RIGHT
.
16
C-TEMP
...3200K, 5400K, 6500K, 7500K, 9300K, Native...
17
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, ChessBoard, CrossHatch, V Burst, H Burst, ColorBar...
18
19
3D FORMAT
...Off, Auto, Side-by-Side, Top-and-Bottom, Dual
Pipe...
Rev B August 2014 Page 25
Important Information
Digital Projection HIGHlite Laser 3D Series
This page is intentionally left blank.
Page 26 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
超高亮度数字视频投影仪
重要信息
目录
用户手册中使用的符号..........................................................28
电气和物理规格................................................................29
激光警示......................................................................29
产品标签......................................................................30
标签位置 ............................................................................31
激光光圈的位置................................................................32
联锁开关......................................................................32
镜头盖........................................................................33
一般注意事项..................................................................34
安装注意事项..................................................................35
操作和配置注意事项............................................................36
国际标准合规情况..............................................................36
射频干涉 ............................................................................36
欧盟废弃电气或电子设备指令 ..........................................................36
基础操作说明..................................................................37
屏幕与投影仪的摆放位置 ..............................................................37
连接电源 ............................................................................38
接通投影仪电源 ......................................................................39
关闭投影仪电源 ......................................................................39
选择输入信号 ........................................................................39
选择测试模型 ........................................................................39
调整镜头 ............................................................................40
调整图像 ............................................................................41
插入新的镜头 ........................................................................42
取下镜头 ............................................................................43
更换过滤器 ..........................................................................44
控制面板......................................................................46
遥控器........................................................................48
有关投影仪操作、连接和设置的完整信息,可以查看光盘上的《用户手册》。
Rev B August 2014 Page 27
Digital Projection HIGHlite Laser 3D Series
用户手册中使用的符号
激光警告:该符号表示除非严格遵守使用说明,否则眼睛可能受到激光辐射。
电击警告:该符号表示除非严格遵守使用说明,否则存在电击危险。
警告:该符号表示除非严格遵守使用说明,否则您本人或设备可能遭受物理伤害危险。
注释:该符号表示您应当阅读一些重要信息。
相关规格可能不经通知而发生变更。
Page 28 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
电气和物理规格
电源电压
工作温度
保存温度
工作湿度
重量
功耗
散热
激光警示
200-240 交流电压,
50-60 赫兹(单向)
0°C 至 35°C
-20℃ 至 60℃
20% 至 90%,无凝露
46.5 千克(102.5 英磅)(不含镜片)
1600 瓦
5027 BTU/小时
3R 级激光产品
在所有操作过程中,本激光产品的设计为 3R 级产品。
激光 - 避免眼睛直接暴露。
不要也不得允许他人将激光器或激光指向或反射到其他人或反射性物体上。
直射光或散射光可能给眼睛和皮肤造成危险。
如果没有遵守所附说明书,可能使眼睛暴露于激光辐射之下。
小心——如果在使用控制、调整设备或执行相关程序时,没有遵守本手册规定,则可能受到危
险的激光辐射。
2 级范围。3R 级激光产品根据 IEC 60825-1 标准,可以产生少量激光辐射危险,对于非光束
内观看而言是安全的。推荐观众距离镜头盖出口平面 100 厘米之外,并将激光辐射危险降低至
更为安全的 2 级辐射。
非激光放射。投影镜头还存在非激光放射。这部分放射已经根据 IEC/EN 62471 标准进行测
试,属于 1 号风险组(低风险)。
激光参数:
波长
激光功率分类
总内部功率
表观光源大小
发散角
工作模式
调制(帧速)
445 纳米 - 470 纳米
< 330 兆瓦
> 35 瓦
> 10 毫米,透镜光阑位置
1 弧度至 100 微弧度
CW
23 - 192 赫兹
Rev B August 2014 Page 29
Digital Projection HIGHlite Laser 3D Series
产品标签
(
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机 )
Model/Modèle
(型號 / 型号):
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
Made in China.
(製造地:中國/製造地:中國)
HIGHlite Laser WUXGA 3D
DLP P ROJECTOR / DLP Projecteur
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
AC Input / Entrée CA
(
(輸入 / 输入):
200-240Vac 8A 50/60Hz
數 位 投 影 機 / 数 字 投 影 机
(1) this device may not cause harmful interference, and
( 型號 / 型号 ):
)
Made in China.
( 製造地:中國/製造地:中國 )
HIGHlite Laser WUXGA 3D
警告: 此為
A 級產品,在生活環境中,該產品可能會造成無線電干擾。
AC Input / Entrée CA
( 輸入 / 输入 )
:
200-240Vac 9.2A 50/60Hz
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
This device complies with part 15 of the FCC rules.
CAN ICES-3 (A)/NMB-3(A)
Complies with FDA performance standards for laser products except for
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
AVOID DIRECT EYE EXPOSURE
警告: 此為 A 級產品,在生活環境中,該產品可能會造成無線電干擾。
在這種情況下,可能需要用戶對干擾採取切實可行的措施。
S/N: XXXXXXXXXXXX
1
2
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
认证声明标签
3
CAUTION – CLASS 4 LASER LIGHT WHEN OPEN
AVOID EYE OR SKIN EXPOSURE TO
CLASS 3R LASER PRODUCT
455-470nm <330mW
保护性外壳标签
3264601800
XXXX XXXX
4
危险警示符号和光圈标签
Page 30 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
标签位置
5
6
7
3
4
1
2
制造商 ID 标签、认证声明标签
和说明标签位于投影仪机身
制造商 ID 标签(制造商名称、
地址和投影仪型号)
认证声明标签
说明标签
序列号
保护外壳标签(位于顶盖下方,
仅维修人员可见)
危险警告标志和光圈标签位于投
影仪机身
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机 )
Model/Modèle (型號 / 型号): HIGHlite Laser WUXGA 3D
AC Input / Entrée CA (輸入 / 输入): 200-240Vac 8A 50/60Hz
Made in China.
(製造地:中國/製造地:中國 )
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
CAN ICES-3 (A)/NMB-3(A)
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
interne réparable par l’utilisateur.
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
警 告 : 請 勿 打 開 外 殼 , 設 備 內 無 服 務 性 維 修 之 元 件
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <330mW
CLASSIFIED IEC/EN 60825-1 2007
S/N: XXXXXXXXXXXX
Code39 of serial no.
(
DLP P ROJECTOR / DLP Projecteur
數 位 投 影 機 / 数 字 投 影 机 )
製造商:
Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
Made in China.
(製造地:中國/製造地:中國)
Model/Modèle (型號 / 型号): HIGHlite Laser WUXGA 3D
AC Input / Entrée CA
(輸入 / 输入): 200-240Vac 8A 50/60Hz
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
CAN ICES-3 (A)/NMB-3(A)
including interference that may cause undesired operation.
警告: 此為
A 級產品,在生活環境中,該產品可能會造成無線電干擾。
在這種情況下,可能需要用戶對干擾採取切實可行的措施。
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
interne réparable par l’utilisateur.
Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <330mW
CLASSIFIED IEC/EN 60825-1 2007
S/N: XXXXXXXXXXXX
Code39 of serial no.
3264601800
XXXX XXXX
1
2
3
4
5
6
128.5
10mm
7
Rev B August 2014 Page 31
Digital Projection HIGHlite Laser 3D Series
激光光圈的位置
激光光圈的位置如下所示。
1
激光光圈
1
联锁开关
主机封盖内安装有五个联锁开关,这些开关一旦激活,将独立切断系统电源。
1 2
3
1
2
3
4
4
当顶盖打开时,将被激活。
当侧盖打开时,将被激活。 x2。当镜头盖打开时,将被激活。
当投影仪镜头被取下时,将被激活。
Page 32 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
镜头盖
镜头盖有两种:短盖和长盖。
装配短镜头盖的投影仪
短镜头盖用于以下镜头:
投射比
0.77 : 1 固定镜头
1.16 : 1 固定镜头
1.45 - 1.74 : 1 缩放镜头
1.74 - 2.17 : 1 缩放镜头
2.17 - 2.90 : 1 缩放镜头
2.90 - 4.34 : 1 缩放镜头
部件编号
110-808
110-809
110-803
112-878
113-852
110-806
长镜头盖必须用于以下长投射比镜头:
投射比
4.34 - 6.76 : 1 缩放镜头
部件编号
110-807
不得将短镜头盖用于长投射镜头。
装配长镜头盖的投影仪
Rev B August 2014 Page 33
Digital Projection HIGHlite Laser 3D Series
一般注意事项
当本设备出现缺陷时,或者封盖或密封件受损时,不得使用本设备。
本设备不可由最终用户自行维护。
不得打开机壳。机壳内部没有用户可以自行维修的部件。
非经过授权的人员,不得进行设备维修。
请仅使用我们提供的电缆。
由于本设备必须接地,因此请确保电源输出口设有接地线。
小心避免纸张或铁丝等小型物体落入投影仪。如果发生这种情况,应立即关闭,并请求经过授
权的维修人员将物体取出。
不要使投影仪淋雨或受潮,不得在投影仪上方放置任何液体。
在清洁之前拔下插头,使用有潮气但没有浸湿的布擦净。
不要用湿手接触电源插头。
不要在雷雨天触碰电源插头。
请小心使用电源电缆,避免过度弯折。禁止使用已经损坏的电缆。
不要触碰出风口,出风口在设备使用期间将会变热。
不得遮盖或阻挡出风口或进风口。
当投影仪开机时,不得遮盖镜头。否则可能引发火灾。
在切断电源或移动投影仪之前,总要让投影仪冷却 5 分钟。
清洁投影仪和镜头时,千万不要使用酒精或稀释剂等强力清洁剂或溶剂。
Page 34 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
安装注意事项
局域网电缆应当仅连接到计算机的局域网接口。其他类似连接器可能存在危险的高压电源。
投影仪的安装必须由具有适当资格的人员完成,并且遵守当地的建筑规范。
投影仪的安装位置应当尽量靠近电源插座。
电源连接应当方便使用,以便在紧急情况下切断电源。
确保出风口与墙壁之间保持至少 30 厘米(12 英寸)的空间,所有其他侧面保持至少 10 厘米
(4 英寸)的空间。
投影仪的安装位置不要靠近可能受到投影仪工作热量影响的任何东西,例如,聚苯乙烯天花
板、窗帘等。
投影仪应当放置在干燥区域,远离尘土、潮湿、蒸汽、烟气、日光或热量的源头。
投影仪较重。在搬运投影仪时,应使用安全的搬运技术。
不得摔落或敲击投影仪。
在安装之前,确保支承投影仪的表面、天花板或索具能够支承投影仪和镜头的合并重量。
当将投影仪叠放时,堆栈必须垂直,确保应力分散到机架的所有四个角。
不要将超过 3 台投影仪堆叠在一起。
不得在投影仪机架上方放置较重物体。只有机架的四个角和选配的装配架才能承受另一台投影
仪的重量。
如果安装在天花板上,应当总是使用后备保险链或保险绳。
投影仪在许多位置都可操作。
唯一不能工作的角度是在纵向模式下,输入端朝上的时候,具体如下图所示:
30SDgr
1
360SDgr
2
1
无法工作的角度
2
可以工作的角度
330SDgr
滚动
2
倾斜
Rev B August 2014 Page 35
Digital Projection HIGHlite Laser 3D Series
操作和配置注意事项
不得修改网络配置,但是您知道自己的行为或者征求了网络管理员意见的情况除外。一旦您出
错,可能您将失去与投影仪的联系。在按下 APPLY(应用)按钮之前,总要再次检查您的设
置。对于原始配置和您做出的修改,总要保留书面记录。
软件更新必须由 Digital Projection 维修人员亲自完成或者在其监督下完成。
国际标准合规情况
射频干涉
美国联邦通讯委员会
除非 Digital Projection 在本手册中做出说明,否则美国联邦通讯委员会不允许对本设备进行任何修
改或变更。如果未能遵守本项政府规定,则可能使您丧失操作本设备的权利。
根据《美国联邦通信委员会规定》第 15 篇规定,本设备经过测试,符合 A 级数字设备限值。这些限
值的设置旨在确保相关设备在商业环境下工作时,合理地防止有害干扰。本设备生成、使用并且能够辐
射射频能量,如果安装和使用不符合说明手册,本设备可能对无线电通信造成有害干扰。在住宅区域操
作本设备,可能造成有害干扰,此时使用者将有责任修正任何干扰。
噪音
GSGV 声噪声信息法令
根据 ISO 3744 或 ISO 7779 标准,本设备的声压等级低于 48 分贝。
欧盟废弃电气或电子设备指令
Digital Projection 公司全力减少废弃的电气和电子设备。我们的产品在设计时,着眼于重
复利用、循环和回收。为此,您的投影仪设备在使用寿命结束时,可以退回 Digital
Projection 公司或其代理商,以此尽量减少环境影响。
Page 36 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
基础操作说明
屏幕与投影仪的摆放位置
1. 安装屏幕,确保屏幕处于最佳观看位置。
2. 安装投影仪,确保投影仪距离合适,使图像填满整个屏幕。调整可调底脚,使投影仪保持水平,并
与屏幕垂直。
下图所示为桌面安装时的底脚位置,以及悬挂安装时的固定孔位置。
1
2
2
2
1
1
2
四个可调底脚
六个悬挂安装用 M6 固定孔
螺钉插入投影仪内部的长度不应超过 15 毫米。
Rev B August 2014
1
2
2
2
1
Page 37
Digital Projection HIGHlite Laser 3D Series
连接电源
开启电缆锁,将主电源接头插入并保持牢固,将电缆锁下压,将电缆锁牢。
1
交流主电源入口,配电缆锁
请仅使用我们提供的电缆。
由于本设备必须接地,因此请确保电源输出口包括接地线。
请小心使用电缆,避免过度弯折。禁止使用已经损坏的电缆。
1
Page 38 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
接通投影仪电源
1. 使用电源电缆连接干线电源与投影仪。打开电源接头一侧的开关。
2. 等待自检完成,并且投影仪控制面板上的
STANDBY
指示灯显示蓝色。系统将处于关闭状态,投影
仪将处于待机模式。
3. 按下遥控器上的
ON
按钮,或者控制面板上的
STBY
按钮,打开投影仪。控制面板上的
ON
指
示灯将显示绿色,系统将亮起,光闸将打开。
关闭投影仪电源
1. 按下遥控器上的
OFF
按钮,或者控制面板上的
STBY
按钮。控制面板上的
ON
指示灯将开始闪
动,系统将熄灭,冷却风扇将运行一会儿,直至投影仪进入待机模式。
2. 如果您想彻底关闭电源,则请关闭电源接口旁边的主电源开关,然后从投影仪上拔下电缆。
选择输入信号
•
将图像源接入投影仪。投影仪将自动检测输入信号,并且在三至三秒内显示。
•
如果连接的信号不止一个,则选择您想显示的输入信号:
•
按下遥控器上的一个输入按钮,或者
•
按下
MENU
,打开屏幕显示功能 (OSD)。高亮选中主菜单的
Input
选项 ,按下
ENTER/
SELECT
,然后使用
上下箭头按钮选择输入信号。按下
ENTER/SELECT
,确定您的选择。
选择测试模型
要显示一个测试模型:
•
按下
MENU
按钮,打开屏幕显示功能。高亮选中主菜单上的
Test Patterns
选项,然后使用
左左
箭头按钮选择测试模型。
Rev B August 2014 Page 39
Digital Projection HIGHlite Laser 3D Series
调整镜头
调整镜头时,可以使用
Lens
菜单,或者使用遥控器上的
LENS
按钮。
按钮
LENS
打开
Lens Control
设置,该设置可以调整缩放、焦距和位移。使用
Lens
菜单,您可进
入
Lens Control
设置和
Lens Center
命令。
Lens Control
Adjustment
选项可以让您使用箭头按钮,调整
Zoom
、
Focus
和
Shift
。该设置分为
Zoom/Focus
模式和
Shift Adjustment
模式。
按下
ENTER/SELECT
按钮,在不同模式之间切换:
•
Zoom/Focus Adjustment
模式,使用源图像
•
Shift Adjustment
模式,使用源图像
•
Zoom/Focus Adjustment
模式,使用校直格栅
•
Shift Adjustment
模式,使用校直格栅
•
Zoom/Focus Adjustment
模式,使用纵横测试
•
Shift Adjustment
模式,使用纵横测试
•
Zoom/Focus Adjustment
模式,使用屏幕布置模型
•
Shift Adjustment
模式,使用屏幕布置模型
1.60:1 (16:10)
1.66:1
1.78:1 (16:9)
1.85:1
1.33:1 (4:3)
2.35:1
...
Page 40 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
调整图像
•
可从
Setup
菜单进行设置。
高亮选中
Orientation
选项,然后从
Desktop Front
、
Ceiling Front
、
Desktop Rear
和
Ceiling Rear
中进行选择。
•
可从
Geometry
菜单进行设置。
•
亮度
、
对比度
和
伽马
等,可从
Image
菜单设置。
•
您也可按下遥控器上的
BRIGHTNESS
、
CONTRAST
或
GAMMA
,设置
亮度
、
对比度
或
伽马
。
Rev B August 2014 Page 41
Digital Projection HIGHlite Laser 3D Series
插入新的镜头
在更换镜头之前,总要确保投影仪已经关闭,并且电源完全断开。
在更换镜头时,避免用力过大,以免损坏设备。
如果镜头和镜头盖没有安装,投影仪不会加电。
注意保存原始的镜头包装和保护盖,以备将来使用。
1. 将镜头插入镜头光圈,确保变焦驱动机构
上的插头与镜头光圈右侧的插口对齐。
2. 按顺时针方向旋转镜头,直至卡嗒一声
到位。
3. 使用螺钉,将镜头盖固定到投影仪前部。
Page 42 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
取下镜头
在更换镜头之前,总要确保投影仪已经关闭,并且电源完全断开。
在更换镜头时,避免用力过大,以免损坏设备。
注意保存原始的镜头包装和保护盖,以备将来使用。
如果镜头和镜头盖没有安装,投影仪不会加电。
1. 松开固定镜头盖的四颗螺钉。
取下镜头盖。
2. 按下镜头的卡头。
3. 按逆时针方向旋转镜头。 4. 将镜头外拉,从光圈上取下镜头。
Rev B August 2014 Page 43
Digital Projection HIGHlite Laser 3D Series
更换过滤器
在更换过滤器之前,总要确保投影仪已经关闭,并且电源完全断开。
在更换过滤器时,避免用力过大,以免损坏设备。
在正常环境下,过滤器应当每 2000 小时更换一次。
1. 松开过滤器盖板的固定螺钉。
2. 取下旧过滤器。
Page 44 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
3. 插入新过滤器。确保过滤器板上的气流箭头指向投影仪(如图所示)。
4. 重新装上过滤器盖板,拧紧螺钉
Rev B August 2014 Page 45
控制面板
Digital Projection HIGHlite Laser 3D Series
3
4
1
2
ON
ERROR
MENU
ENTER
6
5
STANDBY
STBY INPUT
7
8
Page 46 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
2
1
3
4
ON 指示灯(绿)
行为
关闭
闪动
打开
ERROR 指示灯(红)
行为
闪动三次,然后暂停
闪动四次,然后暂停
闪动五次,然后暂停
打开
含义
投影仪已经关闭。
投影仪正在预热或冷却。
投影仪已经打开(普通模式)。
含义
风扇故障。
过热。
过滤器故障。
系统错误。
ENTER 按钮
在使用 OSD 导航功能时,确定您的选择。
进入
Lens Control
设置:调整镜头、缩放和图像聚焦。
箭头按钮
5
6
7
8
STANDBY 指示灯(蓝)
行为 含义
打开 投影仪进入待机模式。
MENU 按钮
进入投影仪的 OSD 功能(屏幕显示功能)。
INPUT 按钮
选择输入源。
STBY 按钮
打开和关闭(待机模式)投影仪
Rev B August 2014 Page 47
遥控器
Digital Projection HIGHlite Laser 3D Series
1
2
ON
|
POWER OFF
1
4
SOURCE
2
PIC
MUTE
3
5
10
3
ENTER
4
5
6
7
8
9
MENU
A
USER MEMORY
B
ASPECT
RATIO
C
SHARP
GAMMA
LENS
2D/3D
O-SCAN
C-TEMP
3D
SWAP
NR
TEST
3D
FORMAT
11
12
13
15
16
17
14
18
19
Page 48 Rev B August 2014
Digital Projection HIGHlite Laser 3D Series
1
2
电源开关
输入选择
选择输入源。
3
4
5
6
7
8
9
10
11
12
导航
使用箭头按钮选择菜单,使用
ENTER
按钮确定选择。
MENU
进入投影仪的 OSD 功能(屏幕显示功能)。
User Memory
载人预先设置选项 A、B 或 C。
对比度
开启
Contrast
控件,然后使用
左左
箭头按钮调整数值。
GAMMA
调整到下一个
伽马
值:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
LENS
调整镜头位置、缩放和焦距。
2D/3D
切换 2D 与 3D 模式。
PIC MUTE
关闭和打开光闸。
ASPECT RATIO
切换至下一个纵横比:
...16:9、TheaterScope、4:3、4:3 Narrow, 16:10、5:4、Source...
BRIGHTNESS
开启
Brightness
控件,然后使用
左左
箭头按钮调整数值。
13
14
15
O-SCAN
切换到
过扫描
模式:
...Off, Crop, Zoom...
C-TEMP
切换至下一个色温:
...3200K, 5400K、6500K、7500K、9300K、Native...
3D SWAP
将 3D 信号源的主要位置在左右眼之间切换(左眼优先)。
16
17
18
SHARP
开启
Sharpness
控件,然后使用
左左
箭头按钮调整数值。
NR
开启
Noise Reduction
控件,然后使用
左左
箭头按钮调整数值。
TEST
...Off, White, Black, Red, Green, Blue, CheckerBoard, CrossHatch, V Burst, H
Burst, ColorBar....
19
3D FORMAT
在各种 3D 格式之间切换:
...Off、Auto、Side-by-Side、Top-and-Bottom、Dual Pipe...
Rev B August 2014 Page 49
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project