JBL CINEMA SB170
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
Verify Line Voltage Before Use
The JBL CINEMA BAR 170 (soundbar and subwoofer) has been designed for use with 100-240 volt, 50/60 Hz AC current.
Connection to a line voltage other than that for which your product is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model or about the line voltage in your area, contact your retailer or customer service representative before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied with your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord that meets factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use this speaker for any considerable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product.
Opening the cabinet may present a shock hazard, and any modification to the product will void your warranty. If water accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.
TABLE OF CONTENTS
3.1 CONTROLS AND INDICATORS
3.2 CONNECTORS
3.3 SUBWOOFER
3.4 REMOTE CONTROL
4.1 DESKTOP PLACEMENT
4.2 WALL-MOUNTING
5.1 TV CONNECTION
5.2 BLUETOOTH CONNECTION
6.1 POWER-ON/AUTO STANDBY/AUTO WAKEUP
6.2 PLAY FROM THE TV SOURCE
6.3 PLAY FROM THE BLUETOOTH SOURCE
7.1 PRE-DEFINED EQ SETTINGS
7.2 VOICE MODE
11
11
11
9
10
10
8
8
5
6
5
6
7
7
www.jbl.com
1 INTRODUCTION
Thank you for purchasing the JBL CINEMA BAR 170 (soundbar and subwoofer) which is designed to bring an extraordinary sound experience to your home entertainment system. We encourage you to take a few minutes to read through this manual, which describes the product and includes step-by-step instructions for setting up and getting started.
To make the most of product features and support, you may need to update the product software through the USB connector in the future. Refer to the software update section in this manual to ensure that your product has the latest software.
Designs and specifications are subject to change without notice.
If you have any questions about the soundbar, installation or operation, please contact your retailer or customer service representative, or visit our website: www.jbl.com.
2 WHAT’S IN THE BOX
Unpack the box carefully and ensure that the following parts are included. If any part is damaged or missing, do not use it and contact your retailer or customer service representative.
Main unit
Subwoofer
Remote control (with 2 AAA batteries)
(AAA)
Power cord* x 2
* Power cord quantity and plug type vary by region.
HDMI cable
Wall-mounting kit
Product information & wall-mounting template
3 PRODUCT OVERVIEW
3.1 Controls and indicators
1 2 3 4
1. (Power)
• Switch on or to standby
2. -/+ (Volume)
• Decrease or increase the volume
• Press and hold to decrease or increase the volume continuously
• Press the two buttons together to mute or unmute
3. (Source)
• Select a sound source: Bluetooth (default) or HDMI
ARC (TV connected through the connector) connector), or Optical (TV / digital device connected through the
4. Status indicators
Solid red
Solid amber
Solid white
Solid blue
Fast flashing blue
Flashing blue
Slow flashing blue
Entering standby mode
Optical source selected
HDMI ARC source selected
Connected to Bluetooth
Entering Bluetooth pairing mode
Volume change ongoing
Maximum volume level reached
Sound muted
3.2 Connectors
1 2 3 4
AC~
SERVICE ONLY
USB HDMI ARC OPTICAL
1.
• Connect to power
2.
• USB connector for software update
• Connect to a USB storage device for audio play (for the
US version only)
3.
• Connect to the HDMI ARC input on your TV
4.
• Connect to the optical output on your TV or digital device www.jbl.com
3.3 Subwoofer
1
2
3
3.4 Remote Control
1
2
6
5
4
3
1.
• Connect to power
2. Connection status indicator
Solid amber
Fast flashing amber
Slow flashing amber
Connected to the soundbar
Pairing mode
Standby mode
3.
• Press and hold to reconnect the subwoofer with the soundbar
1.
• Switch on or to standby
2. Source selectors
• Select the HDMI ARC source
• Select the Optical source
• Select the Bluetooth source
• Press and hold to connect another Bluetooth device
3. Sound effect buttons
/ MUSIC / MOVIE
• Select the pre-defined EQ (equalizer) settings for news/ music/ movie
• Select the voice mode to enhance vocal clarity
4. Playback buttons
I / I
• Bluetooth source: Skip to the previous or next track
• Bluetooth source: Start or pause playback
5. + / -
• Increase or decrease the volume
• Press and hold to increase or decrease the volume continuously.
6. (Mute)
• Mute/unmute
4 PLACE
4.1 Desktop placement
Place the soundbar and subwoofer on a flat and stable surface.
Make sure that the subwoofer is at least 3 ft (1 m) away from the soundbar, and 4” (10 cm) away from a wall.
4.2 Wall-mounting
> 10cm/4”
1m/3ft
5 cm / 2”
2.5-3.0 m / 8.2-9.8 ft
5
>2” (50mm) 1a)
1b)
1
2
≤8 mm/0.31"
1c)
4mm/ 0.16"
≥30 mm/1.18"
3 4
Figure 1
5
NOTES:
− The power cord shall be properly connected to power.
− Do not place any objects on the top of the soundbar or subwoofer.
− Make sure that the distance between the subwoofer and the soundbar is less than 20 ft (6 m).
1. Preparation: a) With a minimum distance of 2” (50mm) from your TV, stick the supplied wall-mounting template to a wall by using adhesive tapes.
b) Use your ballpen tip to mark the screw holder location.
Remove the template. c) On the marked location, drill a 4 mm/0.16” hole. Refer to
Figure 1 for the screw size.
2. Install the wall-mounting bracket.
3. As shown in the diagram, remove the fastening screw by using a screwdriver.
4. Fasten the wall-mounting screw included in the supplied mounting kit.
5. Mount the soundbar.
NOTES:
− Make sure that the wall can support the weight of the soundbar.
− Install on a vertical wall only.
− Avoid a location under high temperature or humidity.
− Before wall-mounting, make sure that cables can be properly connected between the soundbar and external devices.
− Before wall-mounting, make sure that the soundbar is unplugged from power. Otherwise, it may cause an electric shock.
www.jbl.com
5 CONNECT
5.1 TV connection
Connect the soundbar with your TV through the supplied HDMI cable or an optical cable (sold separately).
Through the supplied HDMI cable
An HDMI connection supports digital audio and video with a single connection. HDMI connectivity is the best option for your soundbar.
5.2 Bluetooth connection
Through Bluetooth, connect the soundbar with your Bluetooth device, such as a smartphone, tablet and laptop.
Settings Bluetooth
Bluetooth
DEVICES
JBL CINEMA SB170
Now Discoverable
HDMI ARC
< 10 m / 33 ft
HDMI (ARC)
1. Connect the soundbar with your TV by using the supplied
HDMI cable.
2. On your TV, check that HDMI-CEC and HDMI ARC have been enabled. Refer to the owner’s manual of your TV for more information.
NOTES:
− Full compatibility with all HDMI-CEC devices is not guaranteed.
− Contact your TV manufacturer if you have problems with the HDMI-
CEC compatibility of your TV.
Through an optical cable
OPTICAL
Connect a Bluetooth device
1. Press
to switch on (See ”6.1 Power-on/Auto standby/Auto wakeup” in the ”6 PLAY”
chapter).
2. To select the Bluetooth source, press on the soundbar or on the remote control.
→ Ready for pairing: The status indicator flashes blue.
3. On your Bluetooth device, enable Bluetooth and search for “
” within three minutes.
→ Connected: The status indicator lights up solid blue. A confirmation tone is heard.
To reconnect the last paired device
Your Bluetooth device is retained as a paired device when the soundbar goes to standby mode. Next time you switch to the
Bluetooth source, the soundbar reconnects the last paired device automatically.
OPTICAL
• Connect the soundbar with your TV by using an optical cable
(sold separately).
To connect to another Bluetooth device 6 PLAY
6.1 Power-on/Auto standby/Auto wakeup
2 1
AC~
3S
1. In the Bluetooth source, press and hold on the soundbar or
on the remote control until the status indicator flashes blue.
→ The soundbar enters the Bluetooth pairing mode. The status indicator flashes blue.
2. Follow Step 3 under ”Connect a Bluetooth device”.
• If the device has ever been paired with the soundbar, first unpair “ ” on the device.
NOTES:
− The Bluetooth connection will be lost if the distance between the soundbar and Bluetooth device exceeds 33 ft (10 m).
− Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the soundbar, such as microwaves and wireless LAN devices.
AC~
Switch on
1. Connect the soundbar and subwoofer to power by using the supplied power cords.
2. Press to switch on.
→ The subwoofer is connected to the soundbar automatically.
Connected: The connection status indicator turns solid amber( ).
NOTES:
− Use the supplied power cord only.
− Before switching on the soundbar, make sure that you have completed all other connections (See
”5.1 TV connection” in the ”5
CONNECT”chapter).
Auto standby
If the soundbar is inactive for more than 10 minutes, it will switch to standby mode automatically. The subwoofer also goes to standby, and the connection status indicator turns slow flashing amber ( ).
Next time you switch on the soundbar, it returns to the last selected source.
Auto wakeup
In standby mode, the soundbar will wake up automatically when
• the soundbar is connected to your TV through the HDMI
ARC connection and your TV is switched on;
• the soundbar is connected to your TV through an optical cable and audio signals are detected from the optical cable.
www.jbl.com
6.2 Play from the TV source
With the soundbar connected, you can enjoy TV audio from the soundbar speakers.
→ When the status indicator flashes amber on the soundbar, the function of the soundbar button is learnt by your TV remote control button.
4. Repeat Step 3 to complete the button learning.
5. To exit the TV remote control learning mode, press and hold and + on the soundbar until the status indicator flashes amber three times.
6.3 Play from the Bluetooth source
Through Bluetooth, stream audio from your Bluetooth device to the soundbar.
< 10 m / 33 ft
1. Make sure that your TV is set to support external speakers and the built-in TV speakers are disabled. Refer to the owner’s manual of your TV for more information.
2. Make sure that the soundbar has been properly connected to
your TV (See ”5.1 TV connection” in the ”5 CONNECT”chapter).
3. To select the TV source, press on the soundbar or
/ on the remote control.
→ The status indicator turns solid white ( ), if your TV is connected to the soundbar through the connector.
→ The status indicator turns solid amber ( ), if your TV is connected to the soundbar through the connector.
6.2.1 TV remote control setup
To use your TV remote control for both your TV and the soundbar, check that your TV supports HDMI-CEC. If your TV does not
support HDMI-CEC, follow the steps under ”TV remote control learning”.
HDMI-CEC
If your TV supports HDMI-CEC, enable the functions as instructed in your TV user manual. You can control the volume +/-, sound source, and power on/standby functions on your soundbar through the TV remote control.
TV remote control learning
Through IR learning, your Infra-red TV remote control can learn some commands of the soundbar.
1. Check that you have switched the soundbar to standby mode.
2. On the soundbar, press and hold and + until the status indicator flashes amber.
→ You enter the TV remote control learning mode.
3. Within seconds, do the following on the soundbar and your
TV remote control: a) On the soundbar: press and hold one of the following buttons: + , -, and , until the status indicator flashes red three times. b) On your TV remote control: double press the desired button.
1. Check that the soundbar has been properly connected to
your Bluetooth device (See ”5.2 Bluetooth connection” in the
”5 CONNECT” chapter).
2. To select the Bluetooth source, press on the soundbar or on the remote control.
3. Start audio play on your Bluetooth device.
4. Adjust the volume on the soundbar or your Bluetooth device.
7 SOUND SETTINGS
7.1 Pre-defined EQ settings
With the remote control, select the pre-defined EQ (equalizer) settings for your audio playback.
7.2 Voice mode
With the voice mode, vocal clarity is enhanced to allow you to easily hear and understand speech.
NEWS
: sound mode for music
: sound mode for movies
: sound mode for TV programs such as news and weather forecasts
• On the remote control, press mode.
to select the voice www.jbl.com
8 RESTORE FACTORY SETTINGS
By restoring the default settings defined at factories, you remove all your personalized settings from the soundbar.
• On the soundbar, press and hold and for more than 10 seconds.
9 SOFTWARE UPDATE
For optimal product performance and your best user experience,
JBL may offer software updates for the soundbar system in the future. Please visit www.jbl.com or contact JBL call center to receive more information about downloading update files.
1. Check that you have saved the software update file to the root directory of a USB storage device. Connect the USB device to the soundbar.
• Make sure that your USB storage device meets the following requirements:
- Maximum capacity: 64 GB
- File system: FAT32
Software update files
USB
2. To enter the software update mode, press and hold and - on the soundbar for more than 10 seconds.
→ When software updating is complete, you will hear a confirmation tone.
> 10S
NOTES:
− Keep the soundbar powered on and the USB storage device mounted before software updating is complete.
10 RE-CONNECT THE SUBWOOFER
The soundbar and subwoofer are paired at factories. After poweron, they are paired and connected automatically. In some special cases, you may need to pair them again.
2
AC~
1
AC~
To re-enter the subwoofer pairing mode
1. On the subwoofer, press and hold until t he connection status indicator turns fast flashing amber ( ).
2. On the soundbar, press to switch on.
→ The subwoofer is connected to the soundbar automatically.
Connected: The connection status indicator turns solid amber ( ).
NOTES:
− If the wireless connection fails again, check if there is a conflict or strong interference (e.g. interference from an electronic device) around the location. Remove these conflicts or strong interferences and repeat the above procedures.
11 PRODUCT SPECIFICATIONS
General specification:
• Power supply: 100 - 240 V~, 50/60 Hz
• Total speaker power output (Max. @THD 1%): 220 W
• Soundbar power output (Max. @THD 1%): 2 x 52 W
• Subwoofer power output (Max. @THD 1%): 116 W
• Soundbar transducer: 2x (48 x 90) mm racetrack driver +
2x 0.5” tweeter
• Subwoofer transducer: 5.25”, wireless sub
• Standby consumption: 0.5 W
• Operating temperature: 0°C - 45°C
HDMI specification:
• HDMI Video output (With Audio return channel): 1
• HDMI HDCP version: 1.4
Audio specification:
• Frequency response: 40 Hz - 20 kHz
• Max SPL: 82 dB
• Audio inputs: 1 Optical, Bluetooth, USB (USB playback is available in US version. For other versions, USB is for Service only.)
USB specification:
• USB port: Type A
• USB rating: 5 V DC / 0.5 A
• Supporting file format: mp3
• MP3 Codec: MPEG 1 Layer 1/2/3, MPEG 2/2.5 Layer 1/2/3
• MP3 sampling rate: 8 kHz - 48 kHz
• MP3 bitrate:
MPEG 1 Layer 1: 32 kbps - 448 kbps;
MPEG 1 Layer 2: 32 kbps - 384 kbps;
MPEG 1 Layer 3: 32 kbps - 320 kbps;
MPEG 2/2.5 Layer 1: 32 kbps - 256 kbps;
MPEG 2/2.5 Layer 2/3: 8 kbps - 160 kbps
Wireless specification:
• Bluetooth version: 4.2
• Bluetooth profile: A2DP V1.3, AVRCP V1.5
• Bluetooth frequency range: 2402 – 2480 MHz
• Bluetooth Max. transmitting power: <0dBm (EIRP)
• Bluetooth modulation: GFSK, π/4 DQPSK
• 2.4G wireless frequency range: 2400 – 2483.5 MHz
• 2.4G Max. transmitting power: 3 dBm
• 2.4G wireless modulation: FSK
Dimensions:
• Dimensions (W x H x D):
900 x 62 x 67 mm / 35.4” x 2.44” x 2.64” (soundbar);
200 x 320 x 280 mm / 7.87” x 12.6” x 11” (subwoofer)
• Weight: 1.7 kg (soundbar); 4.2 kg (subwoofer)
• Packaging dimensions (W x H x D):
995 x 235 x 405 mm / 39.17” x 9.25” x 15.94”
• Packaging weight (Gross weight): 8.0 kg www.jbl.com
12 TROUBLESHOOTING
Never try to repair the product yourself. If you have problems using this product, check the following before you request services.
System
The unit will not turn on.
• Check if the power cord is plugged into power and the soundbar.
The soundbar has no response to button pressing.
• Restore the soundbar to factory settings (See the
”8 RESTORE FACTORY SETTINGS”
chapter).
Sound
No sound from the soundbar
• Make sure that the soundbar is not muted.
• Select the correct audio input source on the remote control.
• Connect the soundbar to your TV or other devices properly.
• Restore the soundbar to its factory settings by pressing and holding and on the soundbar for more than 10 seconds.
Distorted sound or echo
• If you play audio from your TV through the soundbar, make sure that your TV is muted or the built-in TV speaker is disabled.
Bluetooth
A device cannot be connected with the soundbar.
• Check if you have enabled Bluetooth on the device.
• If the soundbar has been paired with another Bluetooth
device, reset Bluetooth (see ”To connect to another
Bluetooth device” under ”5.2 Bluetooth connection”).
• If your Bluetooth device has ever been paired with the soundbar, reset Bluetooth on the soundbar, unpair the soundbar on the Bluetooth device, and then, pair
the Bluetooth device with the soundbar again (see ”To
connect to another Bluetooth device” under ”5.2 Bluetooth connection”).
Poor audio quality from a connected Bluetooth device
• The Bluetooth reception is poor. Move the source device closer to the soundbar, or remove any obstacle between the source device and the soundbar.
The connected Bluetooth device connects and disconnects constantly.
• The Bluetooth reception is poor. Move the source device closer to the soundbar, or remove any obstacle between the source device and the soundbar.
• For some Bluetooth devices, the Bluetooth connection can be deactivated automatically to save power. This does not indicate any malfunction of the soundbar.
Remote control
The remote control does not work.
• Check if the batteries are drained. If so, replace them with new ones.
• Reduce the distance and angle between the remote control and the main unit.
Failed to complete the TV remote control learning.
• Check if you are using an infra-red TV remote control. The IR learning is not supported by a Bluetooth TV remote control.
13 TRADEMARKS
The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective owners.
14 OPEN SOURCE LICENSE NOTICE
This product contains open source software licensed under
GPL. For your convenience, the source code and relevant build instruction are also available at http://www.jbl.com/opensource.html
.
Please feel free to contact us at:
Harman Deutschland Gmb
HATT: Open Source, Gregor Krapf-Gunther, Parkring 3
85748 Garching bei Munchen, Germany or [email protected] if you have additional question regarding the open source software in the product.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing Administrator, Inc.
Manufactured under license from Dolby Laboratories. Dolby,
Dolby Audio, and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
www.jbl.com
HARMAN International Industries,
Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA www.jbl.com
© 2021 HARMAN International Industries, Incorporated.
All rights reserved.
JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, specifications and appearance are subject to change without notice.
