ERNT-AQB38/

ERNT-AQB38/
Installation Precautions
Renewal Tool Base Adapter
Model
ERNT-AQB38/-AQB35/-AQB32
ERNT-AQB68/-AQB65/-AQB62
ERNT-AQB58/-AQB55/-AQB52
User’s Manual
【安装注意事项】
3. Mounting and Installation
WARNING
Mitsubishi General-Purpose Programmable Controller

警 告
Be sure to shut off all phases of the external power supply before performing installation work.
Failure to do so could result in electric shock or product damage.
3.1 Handling Precautions
● 必须将外部供应电源全相断开后再进行安装作业等。如
果未全相断开,可能会导致触电或产品损坏。
(1)
Do not drop or apply heavy impact to the base adapter. Doing so could result in damage.
(2)
Fully secure the Q base unit and conversion adapter anchor base using the installation
CAUTION

screws, and securely tighten the screws within the specified torque range. Loose screws
could cause a short circuit, fire or malfunction.
Use the base adapter in an environment of the general specifications defined in the MELSEC-Q
注 意
series CPU module user’s manual. Failure to do so could lead to electric shock, fire, malfunction
or product failure or deterioration.

Fully secure the base adapter, Q base unit and conversion adapter anchor base using the
installation screws, and tighten the installation screws securely within the specified torque range.
Failure to do so could cause the product to fall, resulting in damage.
Startup and Maintenance Precautions
WARNING

Be sure to shut off all phases of the external power supply before cleaning and retightening the
Screw Location
● 应在MELSEC-Q系列CPU模块用户手册中记载的一般规格
环境下使用基板适配器。如果在一般规格范围以外的环
境中使用,可能导致触电、火灾、误动作、产品的损坏
或劣化。
● 基板适配器及Q系列基座单元、转换适配器固定台应通过
安装螺栓切实地加以固定,安装螺栓应在规定的扭矩范
围内切实地拧紧。可能因掉落而导致破损。
Tightening Torque Range
Q base unit installation screw (M4 screw)
Conversion adapter anchor base installation screw (M4 screw)
139 to 189N・cm
3.2 Installation Environment
For details of the installation environment, refer to the user’s manual of the MELSEC-Q series CPU
module to be used.
installation screws. Failure to do so could lead to electric shock. Excessively tightened screws
could result in damage, causing the product to fall, a short circuit or product malfunction.
【启动和维护注意事项】
警 告
Disposal Precautions
CAUTION
ERNT-AQB38/-AQB35/-AQB32
ERNT-AQB68/-AQB65/-AQB62
ERNT-AQB58/-AQB55/-AQB52
Model

When disposing of the product, treat it as industrial waste.
● 在清扫或重新紧固端子螺栓时,必须将外部供应全相断
开后再进行。如果未全相断开,可能会导致触电。如果
螺栓拧得过紧,可能会导致掉落、短路或误动作。
【废弃注意事项】
注 意
ERNT-AQB38/-AQB35/-AQB32
ERNT-AQB68/-AQB65/-AQB62
ERNT-AQB58/-AQB55/-AQB52
50EM8557-E(1407)
● 废弃时请将本产品作为工业废弃物处理。
HEAD OFFICE: Hulic KUDAN BLDG.1-13-5,KUDANKITA CHIYODA-KU,TOKYO 102-0073,JAPAN
NAGOYA ENGINEERING OFFICE:139 SHIMOYASHIKICHO-SHIMOYASHIKI,KASUGAI,AICHI 486-0906,JAPAN
4
(25)
1
Q base unit installation screws (M4 x 8)
CPU
200
250
Base adapter
conditions, resulting in medium or minor injury and/or property
CAUTION level instructions may lead to a serious consequence
Please keep this manual in an easy-to-access location for future reference, and be sure to provide the
C
Specifications
表示错误操作可能造成危险后果,引起中度
伤害、轻伤及财产损失。
according to the circumstances. Always follow the precautions of both levels because they are important
to personal safety.
2. Product Specifications
另外,根据情况不同,即使是 注意中记载的事项,也可能
引发严重后果。不管哪个记载的都是非常重要的内容,请务必
遵守。
请妥善保管本手册,以便需要时取阅,并请将本手册交给最终
用户。
Base Adapter Model
ERNT-AQB38
ERNT-AQB68
MELSEC-A Series
Compatible Module
MELSEC-Q Series
Compatible Module
Installable
Conversion Adapter
Anchor Base
A38B
Q312B
ERNT-AQF12
A38HB
Q38B
ERNT-AQF8
A68B
Q612B
Weight
(g)
970
930
Q68B
(C)
B
A
25
表示错误操作可能造成危险后果,引起死亡
或重伤事故。
25
警告
注意
manual to the end user.
(Reference) MELSEC-A Series
Quantity
conditions, resulting in death or severe injury.
damage.
Note that failure to observe the
MELSEC-Q Series
Product
I/O
CAUTION
Indicates that incorrect handling may cause hazardous
machining on the control panel.
Once you have opened the packaging, verify that it contains the following products.
I/O
WARNING
Indicates that incorrect handling may cause hazardous
those of the MELSEC-A series base unit. There is no need for additional screw hole
series installation using the MELSEC-A series installation holes. (Additional hole machining not required)
I/O
In this manual, the safety precautions are ranked as “WARNING” and “CAUTION”.
The base adapter installation holes (4 locations) have the same installation dimensions as
ERNT-AQB58, ERNT-AQB55, ERNT-AQB52). The base adapter is a product that enables MELSEC-Q
I/O
to be used.
The width dimension is smaller than that of the MELSEC-A series.
(2)
I/O
Controller system safety precautions, refer to the user’s manual of the MELSEC-Q series CPU module
(1)
adapter (ERNT-AQB38, ERNT-AQB35, ERTN-AQB32, ERNT-AQB68, ERNT-AQB65, ERNT-AQB62,
I/O
The precautions presented in this manual are concerned with this product only. For Programmable
This manual describes the Mitsubishi general-purpose Programmable Controller renewal tool base
I/O
the product is used correctly.
使用本产品时,请仔细阅读本手册,并充分注意安全,正确地
使用产品。
本手册中标注的注意事项仅记载了与本产品相关的内容。关于
可编程控制器系统的安全注意事项,请参阅所使用的MELSEC-Q
系列CPU模块的用户手册。
在本●安全注意事项●中,安全注意事项的等级分为「警告」
和「注意」。
4. Installation Dimensions
I/O
Before using this product, please read this manual carefully and pay full attention to safety to ensure that
1. Overview
電源
(使用前请务必阅读)
CPU
(Always read these precautions prior to use.)
(15)
● 安全注意事项 ●
200
240
 SAFETY PRECAUTIONS 
C
(C)
B
A
Base Adapter Model
A
B
C
MELSEC-A Series Base
Unit Model
A
B
C
ERNT-AQB38
480
460
10
A38B, A38HB
480
460
10
ERNT-AQB68
466
446
10
A68B
466
446
10
ERNT-AQB58
A58B
Q68B
ERNT-AQF8
870
ERNT-AQB58
411
391
10
A58B
411
391
10
ERNT-AQB35
A35B
Q38B
ERNT-AQF8
795
ERNT-AQB35
382
362
10
A35B
382
362
10
Q35B
ERNT-AQF5
ERNT-AQB65
352
332
10
A65B
352
332
10
ERNT-AQB55
297
277
10
A55B
297
277
10
ERNT-AQB32
247
227
10
A32B
247
227
10
ERNT-AQB62
238
218
10
A62B
238
218
10
ERNT-AQB52
183
163
10
A52B
183
163
10
ERNT-AQB65
A65B
Q68B
790
Q65B Q55B
ERNT-AQB55
A55B
Q65B
ERNT-AQF5
655
Q55B
ERNT-AQB32
A32B
Q33B
ERNT-AQB62
A62B
Q63B
ERNT-AQF3
675
650
Q52B
ERNT-AQB52
A52B
Q52B
505
5. Q Base Unit and Conversion Adapter Anchor Base
5.3 ERNT-AQB58
5.6 ERNT-AQB55
6. External Dimensions
Installation Locations
(15)
Unit:mm
5.1 ERNT-AQB38
A
B
200
B
Conversion adapter anchor base
ERNT-AQF8 installation location
25
a
Conversion Adapter
Anchor Base
5.4 ERNT-AQB35
a
B
A
A
Q65B
b
a
ERNT-AQF12
Q Base Unit
Q312B
A
a
a
Combination not possible
Upper half :
Q base unit installation location
Lower half :
Conversion adapter anchor base screw tightening location
a
ERNT-AQF8
A
A
Upper half :
Q base unit installation location
Lower half :
Conversion adapter anchor base screw tightening location
B
B
5.7 ERNT-AQB32
b
a
Conversion Adapter
Anchor Base
Q Base Unit
b
ERNT-AQF8
ERNT-AQF5
A
A
a
a
Q38B
Q35B
5.2 ERNT-AQB68
Combination not possible
Upper half :
Q base unit installation location
Lower half :
Conversion adapter anchor base screw tightening location
11.8
B
Q55B
Conversion Adapter
Anchor Base
Q38B
ERNT-AQF5
Q Base Unit
11.8
A
240
Q base unit Q68B
installation location
Base Adapter Model
A
B
ERNT-AQB38
480
460
ERNT-AQB68
466
446
ERNT-AQB58
411
391
ERNT-AQB35
382
362
ERNT-AQB65
352
332
ERNT-AQB55
297
277
ERNT-AQB32
247
227
ERNT-AQB62
238
218
ERNT-AQB52
183
163
Q base unit Q33B
installation location
B
b
Conversion adapter anchor base
ERNT-AQF3 installation location
Duplication Prohibited
This manual may not be reproduced in any form, in part or in whole, without written permission
from Mitsubishi Electric Engineering Company Limited.
©2014 MITSUBISHI ELECTRIC ENGINEERING COMPANY LIMITED ALL RIGHTS RESERVED
MELSEC is a registered trademark of Mitsubishi Electric Corporation.
5.5 ERNT-AQB65
5.8 ERNT-AQB62
Product Warranty Details
Please confirm the following product warranty details prior to product use.
Gratis Warranty Terms and Gratis Warranty Range
A
A
B
B
If any fault or defect (hereinafter referred to as “Failure”) attributable to Mitsubishi Electric Engineering
Company Limited (hereinafter referred to as “MEE”) should occur within the gratis warranty period, MEE shall
repair the product free of charge via the distributor from whom you made your purchase.
C
A
a
Conversion Adapter
Anchor Base
b
ERNT-AQF12
a
Conversion Adapter
Anchor Base
ERNT-AQF8
Q Base Unit
b
ERNT-AQF8
A
Q68B
a
Combination not possible
Upper half :
Q base unit installation location
Lower half :
Conversion adapter anchor base screw tightening location
A
a
b
Conversion Adapter
Anchor Base
ERNT-AQF5
A
a
Q65B
Combination not possible
Q55B
Combination not possible
Upper half :
Q base unit installation location
Lower half :
Conversion adapter anchor base screw tightening location
A
ERNT-AQF3

a
a
B
Q52B
b
Gratis Warranty Range
The gratis warranty range shall be limited to normal use based on the usage conditions, methods and
environment, etc., defined by the terms and precautions, etc., given in the instruction manual, user’s
manual and caution labels on the product.
A
Q63B
B
Gratis Warranty Period
The gratis warranty period of this product shall be one (1) year from the date of purchase or delivery to
the designated place.
Note that after manufacture and shipment from MEE, the maximum distribution period shall be six (6)
months, and the gratis warranty period after manufacturing shall be limited to eighteen (18) months.
In addition, the gratis warranty period for repaired products shall not exceed the gratis warranty period
established prior to repair.
Q Base Unit
Q68B
B

a
Q Base Unit
Q612B
B
a
C
Upper half :
Q base unit installation location
b
Lower half :
Conversion adapter anchor base screw tightening location
Warranty Period after Discontinuation of Production
(1)
(2)
5.9 ERNT-AQB52
MEE shall offer product repair services (fee applied) for seven (7) years after production of the product
has been discontinued. Discontinuation of production shall be reported via distributors.
Product supply (including spare parts) is not possible after production has been discontinued.
Exclusion of Opportunity Loss and Secondary Loss from Warranty Liability
Regardless of the gratis warranty period, MEE shall not be liable for compensation for damages arising from
causes not attributable to MEE, opportunity losses or lost profits incurred by the user due to Failures of MEE
products, damages or secondary damages arising from special circumstances, whether foreseen or
unforeseen by MEE, compensation for accidents, compensation for damages to products other than MEE
products, or compensation for other work carried out by the user.
Q base unit Q52B
installation location
Conversion adapter anchor base
ERNT-AQF3 installation location
Changes in Product Specifications
The specifications given in the catalogs, manuals and technical documents are subject to change without
notice.
This document is a new publication, effective July 2014. Specifications are subject to change without notice.
Developed July 2014
50EM8557-E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement