Automotive Data Solutions Rockford Fosgate DSR1 Install Manual
Automotive Data Solutions Rockford Fosgate DSR1 is a seamless aftermarket amplifier installation solution that enables you to keep your original radio while upgrading your sound system. It works with the iDatalink Maestro aCH2 Installation Harness and offers various features to enhance your car audio experience. With this device, you can:
- Integrate your aftermarket amplifier with the factory system without replacing the head unit.
- Easily connect and configure the amplifier using the included T-harness and wiring diagram.
- Adjust the chime volume to your preference for parking assist and other alerts.
PDF
Download
Document
Advertisement
Advertisement
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your DSR1 module according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. INSTALL GUIDE Chrysler 200 2015-2016 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Chrysler 200 2015-2016 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Chrysler 200 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Chrysler 200 2015-2016 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Chrysler 200 2015-2016 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Mid (+) White/Black Left Front Mid (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Mid (+) Gray/Black Right Front Mid (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Mid (+) Green/Black Left Rear Mid (-) Green Subwoofer 1 (+) Green/Red Subwoofer 1 (-) Purple Right Rear Mid (+) Purple/Black Right Rear Mid (-) Purple Subwoofer 2 (+) Purple/Red Subwoofer 2 (-) Orange Left Rear Tweeter (+) Orange/Black Left Rear Tweeter (-) Black n/a Black/White n/a Black Right Rear Tweeter (+) Black/Red Right Rear Tweeter (-) Black n/a Black/Yellow n/a Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Right end of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Chrysler 300 2012-2016 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Chrysler 300 2012-2016 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Chrysler 300 2012-2016 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Chrysler 300 2012-2016 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Chrysler 300 2012-2016 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Left Rear Tweeter (+) Green/Red Left Rear Tweeter (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Right Rear Tweeter (+) Purple/Red Right Rear Tweeter (-) Orange Center Speaker (+) Orange/Black Center Speaker (-) Black Subwoofer 1 (+) Black/White Subwoofer 1 (-) Black Subwoofer 2 (+) Black/Red Subwoofer 2 (-) Black Subwoofer 3 (+) Black/Yellow Subwoofer 3 (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left end of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Dodge Challenger 2015-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Dodge Challenger 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Dodge Challenger 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Dodge Challenger 2015-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Dodge Challenger 2015-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Left Rear Mid (+) Green/Red Left Rear Mid (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Right Rear Mid (+) Purple/Red Right Rear Mid (-) Orange Center Speaker (+) Orange/Black Center Speaker (-) Black Subwoofer 1 (+) Black/White Subwoofer 1 (-) Black Subwoofer 2 (+) Black/Red Subwoofer 2 (-) Black n/a Black/Yellow n/a Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left end of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Dodge Charger 2012-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Dodge Charger 2012-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Dodge Charger 2012-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Dodge Charger 2012-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Dodge Charger 2012-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Left Rear Speaker (+) Green/Red Left Rear Speaker (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Right Rear Speaker (+) Purple/Red Right Rear Speaker (-) Orange Center Speaker (+) Orange/Black Center Speaker (-) Black Subwoofer 1 (+) Black/White Subwoofer 1 (-) Black Subwoofer 2 (+) Black/Red Subwoofer 2 (-) Black Subwoofer 3 (+) Black/Yellow Subwoofer 3 (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left side of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Dodge Durango 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Dodge Durango 2014-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Dodge Durango 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Dodge Durango 2014-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Dodge Durango 2014-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Subwoofer 2 (+) Green/Red Subwoofer 2 (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Subwoofer 1 (+) Purple/Red Subwoofer 1 (-) Orange Left Rear Tweeter (+) Orange/Black Left Rear Tweeter (-) Black Right Rear Tweeter (+) Black/White Right Rear Tweeter (-) Black n/a Black/Red n/a Black Center Speaker (+) Black/Yellow Center Speaker (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left side of cargo area Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Dodge Journey 2011-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Dodge Journey 2011-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Dodge Journey 2011-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Dodge Journey 2011-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Dodge Journey 2011-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Subwoofer 1 (+) Green/Red Subwoofer 1 (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Subwoofer 2 (+) Purple/Red Subwoofer 2 (-) Orange n/a Orange/Black n/a Black n/a Black/White n/a Black n/a Black/Red n/a Black n/a Black/Yellow n/a Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Center console Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Jeep Cherokee 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Jeep Cherokee 2014-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Jeep Cherokee 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Jeep Cherokee 2014-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Jeep Cherokee 2014-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Tweeter (+) Green/Black Left Rear Tweeter (-) Green Subwoofer 1 (+) Green/Red Subwoofer 1 (-) Purple Right Rear Tweeter (+) Purple/Black Right Rear Tweeter (-) Purple Subwoofer 2 (+) Purple/Red Subwoofer 2 (-) Orange Left Rear Speaker (+) Orange/Black Left Rear Speaker (-) Black n/a Black/White n/a Black Right Rear Speaker (+) Black/Red Right Rear Speaker (-) Black Center Speaker (+) Black/Yellow Center Speaker (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Right end of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Jeep Grand Cherokee 2014-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Jeep Grand Cherokee 2014-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Jeep Grand Cherokee 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Jeep Grand Cherokee 2014-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Jeep Grand Cherokee 2014-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Subwoofer 2 (+) Green/Red Subwoofer 2 (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Subwoofer 1 (+) Purple/Red Subwoofer 1 (-) Orange Left Rear Speaker (+) Orange/Black Left Rear Speaker (-) Black Right Rear Speaker (+) Black/White Right Rear Speaker (-) Black n/a Black/Red n/a Black Center Speaker (+) Black/Yellow Center Speaker (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left side of cargo area Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Ram 1500 2013-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Ram 1500 2013-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Ram 1500 2013-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Ram 1500 2013-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Ram 1500 2013-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Subwoofer 1 (+) Green/Red Subwoofer 1 (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Center Speaker (+) Purple/Red Center Speaker (-) Orange Left Rear Tweeter (+) Orange/Black Left Rear Tweeter (-) Black Right Rear Tweeter (+) Black/White Right Rear Tweeter (-) Black n/a Black/Red n/a Black Subwoofer 2 (+) Black/Yellow Subwoofer 2 (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left end of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 INSTALL GUIDE Ram 2500 & 3500 2013-2017 ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION, WITHOUT CHANGING YOUR RADIO. PRODUCTS REQUIRED Rockford Fosgate DSR1 iDatalink Maestro aCH2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-DSR1-CHR03 NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Ram 2500 & 3500 2013-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifier replacement solution. You are now a few simple steps away from enjoying your new car amplifier. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Vehicle Wire Reference Chart 5 Before starting your installation, please ensure that your module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 2 Ram 2500 & 3500 2013-2017 INSTALLATION INSTRUCTIONS STEP 1 • For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” • Remove the factory amplifier (refer to wire chart for amplifier location). • Configure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram. STEP 2 • Connect the factory amplifier harnesses to the aCH2 T-harness. STEP 3 • Connect the wires from the aCH2 T-harness to the aftermarket amplifier. Note 1: If you are running your own speaker wires from the amplifier to the speakers, this step is not necessary. Note 2: The amplifier output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, see the wiring chart. • Plug the RCA cables in the aftermarket amplifier. STEP 4 • Connect all the harnesses to the DSR1 module. CHIME ADJUSTMENT This is only needed when the vehicle supports chimes (ex: Parking assist, Blind spot detection, Lane sense, etc.). • Set the audio source to OFF (if there is no way to turn the radio OFF, set the source to AUX). • The OEM radio will have 3 volume settings for parking assist (Low/Med/High), it is recommended to choose medium volume. • Activate any chime (ex: rear parking assist). • Adjust the chime volume using the volume knob. 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 3 Ram 2500 & 3500 2013-2017 WIRING DIAGRAM STEP 3 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK GREEN GREEN/RED PURPLE PURPLE/RED BLACK BLACK/WHITE BLACK BLACK/RED WHITE WHITE/RED GRAY GRAY/RED BLACK BLACK/YELLOW ORANGE ORANGE/BLACK AMPLIFIER STEP 2 LEFT FRONT 1 FACTORY AMPLIFIER HARNESSES RIGHT FRONT 1 LEFT REAR 1 WIRES FROM VEHICLE RIGHT REAR 1 LEFT REAR 2 RIGHT REAR 2 SUB 1 SUB 2 LEFT FRONT 2 RIGHT FRONT 2 SUB 3 CENTER 1 aCH2 T-HARNESS STEP 4 STEP 1 GRAY GRAY WHITE WHITE PURPLE GREEN BLUE RED DSR1 MODULE PURPLE GREEN N.C. N.C. RCA CABLES LEFT FRONT OUT 1 RIGHT FRONT OUT 2 LEFT SPARE OUT 3 RIGHT SPARE OUT 4 LEFT REAR OUT 5 RIGHT REAR OUT 6 LEFT SUB OUT 7 RIGHT SUB OUT 8 CONNECTIONS NOT REQUIRED 1 Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 4 Ram 2500 & 3500 2013-2017 VEHICLE WIRE REFERENCE CHART T-Harness Wires Vehicle Wires Wire Tag LEFT FRONT 1 LEFT FRONT 2 RIGHT FRONT 1 RIGHT FRONT 2 LEFT REAR 1 LEFT REAR 2 RIGHT REAR 1 RIGHT REAR 2 CENTER 1 SUB 1 SUB 2 SUB 3 Wire Color Speaker Wire Description White Left Front Speaker (+) White/Black Left Front Speaker (-) White Left Front Tweeter (+) White/Red Left Front Tweeter (-) Gray Right Front Speaker (+) Gray/Black Right Front Speaker (-) Gray Right Front Tweeter (+) Gray/Red Right Front Tweeter (-) Green Left Rear Speaker (+) Green/Black Left Rear Speaker (-) Green Subwoofer 1 (+) Green/Red Subwoofer 1 (-) Purple Right Rear Speaker (+) Purple/Black Right Rear Speaker (-) Purple Center Speaker (+) Purple/Red Center Speaker (-) Orange Left Rear Tweeter (+) Orange/Black Left Rear Tweeter (-) Black Right Rear Tweeter (+) Black/White Right Rear Tweeter (-) Black n/a Black/Red n/a Black Subwoofer 2 (+) Black/Yellow Subwoofer 2 (-) Note: The amplifier output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specific wiring designation, follow this wiring chart. Amplifier location: Left end of dash Automotive Data Solutions Inc. © 2019 ADS-DSR1-CHR02B-AR maestro.idatalink.com 5 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Frequently asked questions
The Automotive Data Solutions Rockford Fosgate DSR1 enables a seamless aftermarket amplifier installation without changing the radio.
Rockford Fosgate DSR1 and iDatalink Maestro aCH2 Installation Harness are required for the installation.
Programmed firmware ADS-DSR1-CHR03 is available as an optional accessory.
Open the Bookmarks menu or scroll down until you find the installation guide for your vehicle.
Use the advanced options in the Print menu to print only the pages for your vehicle.
Follow the installation guide for your vehicle to install the DSR1 module.
Pressing the printer icon or quick printing the document will print all of the guides in this compilation.
Contact customer support at 1 866 427-2999, email [email protected], visit maestro.idatalink.com/support, or visit www.12voltdata.com/forum for assistance.