Harken Radial Winch 40.2STE Owner's Manual
Advertisement
Advertisement
Installation and Maintenance Manual
MRW-02
Powered Radial Winch
40.2 ST E/HY
Index
Introduction
Technicalcharacteristics
Performance data
Weight
Maximum working load
Outline
Installation
Procedure 1
Procedure 2
Winch installation procedure
Positioning the self-tailing arm
Motorinstallationprocedure
Electric wiring diagrams
Maintenance
Washing
Maintenance table
Disassembly procedure
Exploded view with maintenance products
Assembly
Harken ® limitedworldwidewarranty
Orderingspareparts
Explodedview
PartsList
Radial Winch 40.2 STA
Radial Winch 40.2 STC
Radial Winch 40.2 STCW
Horizontal electric motor 12V/24V
11
12
15
15
15
15
19
20
21
21
22
24
24
25
26
27
5
8
10
6
7
11
3
4
4
3
3
Radial Winch 40.2 ST E/HY 2 Installation and Maintenance Manual
Introduction - Technical characteristics - Outline
Introduction
This manual gives technical information on winch installation and maintenance, including disassembling and reassembling.
This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.
Installation, disassembling and reassembling of the winch by personnel who are not experts may cause serious damage to users and those in the vicinity of the winch.
Harken ® accepts no responsibility for defective installation or reassembly of its winches.
In case of doubt the Harken ® Tech Service is at your disposal at [email protected]
This Manual is available only in English. If you do not fully understand the English language, do not carry out the operations described in this Manual.
Technicalcharacteristics
Powerratio
1stspeed 13,50 : 1
2ndspeed 39,90 : 1
The theoretical power ratio does not take friction into account.
Performance data
Winch 40.2 ST E (electric)
Gearratio
2,13 : 1
6,28 : 1 horizontalmotor
12 V (700 W)
1st speed 2nd speed
24 V (900 W)
1st speed 2nd speed
7,9 28,7 9,8 linespeed(m/min)** 23,2 maxload(Kg) 290
**Line speed is measured with no load
850 290 867 winch40.2STE
horizontal motornominalpower(W)
12 V
700
24 V
900 currentabsorptionat winchMWL(A)
12 V
170
24 V
90
Radial Winch 40.2 ST E/HY 3 Installation and Maintenance Manual
Installation
Weight
weight(Kg)
STAEH
13,5
STCEH
15,1
Versions:
A = drum in anodised aluminium
C = drum in chromed bronze
EH = horizontal electric winch
Maximum working load
WARNING!
The maximum working load (MWL) for the 40.2 ST Radial Winch is 850 Kg (1874 lb)
Subjecting the winch to loads above the maximum working load can cause the winch to fail or pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.
Radial Winch 40.2 ST E/HY 4 Installation and Maintenance Manual
Ø80,5
Outline
Winch 40.2 ST E/HY
Ø80,5
Ø80,5
Ø156
Ø156
Ø80,5
Ø156
Ø156
Horizontal electric motor (12 V / 24 V)
Ø156
Ø80,5
Ø156
Ø80,5
Radial Winch 40.2 ST E/HY 5 Installation and Maintenance Manual
130
Ø156
Ø80,5
Ø156
Ø80,5
Ø80,5
Ø156
130
Ø80,5
Ø154,0
Ø180
Ø80,5
Ø156
Ø80,5
Ø154,0
Ø180
Installation
The winch must be installed on a flat area of the deck, reinforced if necessary to bear a load equal to at least twice the maximum working load of the winch.
It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can bear the load.
Harken ® does not supply the screws needed to install the winch since these may vary depending on the deck on which it is to be installed.
It is the installer's responsibility to choose the correct screws taking account of the loads they will have to bear.
Harken ® assumes no responsibility for incorrect installation of its winches or for an incorrect choice of mounting screws.
DANGER!
Incorrect installation of the winch may cause severe injury or death. Consult the yard that built the boat in the case of doubt over the correct positioning of the winch.
WARNING!
Failure to use the correct number and type of mounting fasteners or failure to ensure the correct deck strength can result in the winch pulling off the deck suddenly and unexpectedly during high loads causing severe injury or death.
WARNING!
Verify the entry angle of the sheet. This must be 8° with tolerance of
±2°, to avoid sheet overrides and damaging the winch or making the winch inoperable leading to loss of control of the boat which can lead to severe injury or death.
WARNING!
Mount the winch on the deck so that the drive gear is positioned where the sheet enters the winch drum.
Incorrect position of drive gear can weaken winch leading to failure which can cause an accident leading to severe injury or death.
NOTICE
You can find the icon on the skirt to identify the drive gear position.
SHEET drive gear
8°
After correctly positioning the final drive gear with respect to the load, check that the motor, gearing, electrical wiring and/or hydraulic pipes can be housed below decks. To help find the optimal compromise, remember that, to make the installation of the motor easier, it can be coupled to the winch in any one of four different positions that differ by 40° from each other.
Once you have decided the correct mounting position for the winch on the deck and checked the space available below deck, proceed with the installation.
Radial Winch 40.2 ST E/HY 6 Installation and Maintenance Manual
The winch can be installed following one of the two procedures below (Procedure1 or Procedure 2):
Procedure 1
To install the winch you must remove the drum and use Socket Head (SH) bolts.
Tools needed: One medium flat-bladed screwdriver
To identify the various parts, refer to the exploded view at the end of this Manual.
Torque to apply when assembling
1. Pull out the disconnect rod n°30 2. Unscrew the central screw ( 2Nm/18 in-lb)
3. Slide off the assy socket n°28 and the cover n°29.
Pay attention to the o-ring in the socket.
4. Unscrew the three screws n°27
( 4Nm/35 in-lb)
Radial Winch 40.2 ST E/HY 7 Installation and Maintenance Manual
5. Remove the self-tailing arm n°26 by rotating and lifting it.
6. Lift off the drum n°22
Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 6 and using socket head (SH) bolts.
Procedure 2
To install, you must remove the winch skirt and use hexagonal headed bolts.
Tools needed: One medium flat-bladed screwdriver
To identify the various parts, refer to the exploded view at the end of this Manual.
See (paragraph on installation) the limits described on page 6 and using socket head (SH) bolts.
Torque to apply when assembling
1. Remove the skirt n°2 with the help of the screwdriver placed as shown by the symbol
2. Take off the base n°2
Radial Winch 40.2 ST E/HY 8 Installation and Maintenance Manual
3. Position the 5 M6 hexagonal headed bolts in their holes
4. Reposition the skirt n°2 in its housing 5. Press down the skirt to position it correctly
NOTICE
Make sure the skirt is correctly clipped on to the base of the winch.
Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 6 and using hexagonal headed bolts.
(See paragraph on winch installation)
Radial Winch 40.2 ST E/HY 9 Installation and Maintenance Manual
Winch installation procedure
Carry out Procedure 1 or Procedure 2, then install the winch on the deck in the chosen position.
NOTICE
Before drilling the deck, check the space available below deck for the flange and the motor
A.
Position the base of the winch on the deck and mark the position of the holes or use the drilling cut-out template at the point where you have decided to place the winch.
Below is a reduced scale diagram.
50°
105°
Ø80 cut out for powered winches
70° final pinion position
35°
Winch outside Ø157 Ø6 n°5
50°
50°
Ø123
The drilling cut out template is available on the Harken ® website, www.harken.com
B.
Remove the winch and drill the five 6.2 mm and a 80 mm diameter holes.
C.
Bolt the base of the winch to the deck using five M6 Socket Head (SH) bolts for Procedure
1 or five hexagonal headed M6 bolts for Procedure2 (neither is supplied by Harken ® ), correctly chosen for the thickness and type of the boat deck. Consult the yard that built the boat in case of doubt.
WARNING!
To install the winch on the deck, use only bolts in A4 stainless steel (DIN 267 part11).
Bolts made of other materials may not have sufficient strength or may corrode which can result in winch pulling off deck suddenly and unexpectedly during high loads causing severe injury or death.
NOTICE
To mount winches on the deck, do not use countersunk bolts.
D.
Fill the mounting holes with a suitable marine sealant.
E.
Remove the excess adhesive/sealant from the holes and base drainage channels
F.
Reassemble the winch following the steps in Procedure1 or Procedure2 in the reverse order, and apply the products indicated in the section on maintenance.
Radial Winch 40.2 ST E/HY 10 Installation and Maintenance Manual
NOTICE
Before closing the winch, make sure the holes and drainage channels in the base of the winch are not obstructed.
Positioning the self-tailing arm
Position the self-tailing arm so that the line leaving the winch is led into the cockpit.
Motorinstallationprocedure
Once you have installed the winch on the deck, proceed with motor installation. The motor can be coupled to the winch in different positions. Check the space available below deck and choose the suitable position.
Tools needed
A number five hex key
A number six hex key (only for vertical electric motor)
A number ten hex key (only for hydraulic motor)
Two number thirteen wrenches
1. Position the flange (see Page 12) 2. Tighten the six screws ( 8 Nm/ 71 in-lb)
3. Position the reduction gear and motor
Radial Winch 40.2 ST E/HY 11
4. Tighten the two screws ( 8 Nm/ 71in-lb).
Be sure to align the flange.
Installation and Maintenance Manual
Maintenance
NOTICE
Before positioning the flange, check to make sure that seals (the first one is above the flange and the second one is under the flange) are seated correctly.
After winch is assembled and before sailing, test the powered winch functioning: insert the lock-in winch handle in the handle socket and check that the disconnect rod must disconnect gearbox.
Electric wiring diagrams
To guarantee greater efficiency in terms of safety and long life, for certain winch models it is obligatory to install the WLC200R Load Controller.
WARNING!
Consult the table below to check for which winch models it is obligatory to install the
WLC200R and for which it is recommended.
WINCH
RADIAL
40.2
Horizontalmotor
12V 24V recommended recommended
For more information, refer to the WLC200R Manual.
Refer to the following diagrams for the electric wiring:
Horizontal 12 V / 24 V motor installed without WLC200R
1D1 A2 2D2
WINCH
&
MOTOR
Radial Winch 40.2 ST E/HY
ELECTRICAL
CONTROL BOX
M1 M2
A1 C A2
SWITCHES
CIRCUIT BREAKER
FUSE
12
BATTERY
Installation and Maintenance Manual
Horizontal 12 V / 24 V motor in right-hand configuration installed with WLC200R
WINCH
&
MOTOR
1D1 A2 2D2
M1 M2
A1 C A2
ELECTRICAL
CONTROL BOX
A1 C A2
WLC200R
B40 C. Box-
B44/B70 Motorbatt-
WLC200
SWITCHES
5 amp fuse
CIRCUIT
BREAKER
+ -
BATTERY
Horizontal 12 / 24V motor in left-hand configuration with WLC200R
1D1 A2 2D2
WINCH
&
MOTOR
M1 M2
A1 C A2
ELECTRICAL
CONTROL BOX
A1 C A2
WLC200R
B40 C. Box-
B44/B70 Motorbatt-
WLC200
SWITCHES
5 amp fuse
CIRCUIT
BREAKER
+ -
BATTERY
Radial Winch 40.2 ST E/HY 13 Installation and Maintenance Manual
Fasten electric control box containing solenoids to bulkhead or wall. Install remote circuit breaker between power supply and electric control box. Locate push-buttons on deck in a convenient spot for easy winch operation.
Refer to the following chart for wire size:
Winch size
40.2
40.2
Current voltage
12 V
24 V
Under16.4ft
AWG
2
5
Total distance between winch and battery
Under5m mm 2
32
16
16.4-32.8ft
AWG
0
3
5m-10m mm 2
50
25
32.8-49.2ft
AWG
00
2
10m-15m mm 2
70
35
49.2-65.6ft
AGW
000
0
15m-20m mm 2
95
50
NOTICE
To connect motor, attach cable terminals to clamps between nut and lock nut. Hold nut in contact with motor using a spanner and tighten other nut with second spanner. Take special care not to turn the central spindles. Be careful not to turn central spindles. These instructions apply when assembling and disassembling. We recommend using a torque wrench so as to obtain a torque equal to and no greater than 10 Nm (88 in-lb).
NOTICE
Note that correct electrical contact sequence is:
Nut – Cable Terminal – Self-Locking Washer –
Lock Nut
Radial Winch 40.2 ST E/HY 14 Installation and Maintenance Manual
Maintenance
Washing
Winches must be washed frequently with fresh water, and in any case after each use.
Do not allow teak cleaning products or other cleaners containing caustic solutions to come into contact with winches and especially anodised, chrome plated or plastic parts.
Do not use solvents, polishes or abrasive pastes on the logos or stickers on the winches. Do not use polishes or abrasive pastes on anodised, chromed plated or plastics surfaces.
Make sure that the holes and drainage channels in the base of the winch are not obstructed so that water does not collect.
Maintenance table
Winches must be visually inspected at the beginning and end of every season of sailing or racing.
In addition they must be completely overhauled, cleaned and lubricated at least every 12 months.
After an inspection, replace worn or damaged components. Do not replace or modify any part of the winch with a part that is not original.
WARNING!
Periodic maintenance must be carried out regularly. Lack of adequate maintenance shortens the life of the winch, can cause serious injury and also invalidate the winch warranty.
Installation and maintenance of winches must be carried out exclusively by specialized personnel.
WARNING!
Make sure that the power is switched off before installing or carrying out maintenance on the winch.
In the case of doubt contact Harken ® Tech Service at [email protected]
Disassembly procedure
Tools needed:
One medium flat-bladed screwdriver
A number five hex key
Brush
Rags
To identify the various parts refer to the exploded view at the end of this Manual.
Torque to be applied in assembly phase
Carry out Procedure1 as shown in the paragraph on winch installation and then do the following:
Radial Winch 40.2 ST E/HY 15 Installation and Maintenance Manual
6. Completely unscrew the three screws n° 27 and remove the stripper arm support n°21
7. Slide out the central shaft n°19
8. Unscrew the 5 hex screws n°16
( 20Nm/177 in-lb)
9. Remove the assy housing n°15
Important: washer n°13 may remain inside the drum support!
10. Remove the washer n°13
Radial Winch 40.2 ST E/HY
11. Remove the gear n°7
16 Installation and Maintenance Manual
12. Remove the pawls carrier n°4 13. Remove the gear n°3
14. Remove the gear n°14 15. Remove the gear n°10
16. Remove the pawls carrier n°11 18. Remove the washer n°9
Radial Winch 40.2 ST E/HY 17 Installation and Maintenance Manual
I. Unscrew the 4 screws n°25
( 4Nm/35 in-lb)
II. Remove the jaws n°24
If it is necessary to replace any jaws of the winch, proceed as follows:
Inspect balls inside the drum and carefully check the correct position; if it is necessary to put back any balls, push balls in the race (as shown below):
Once the winch is completely disassembled, clean the parts: use a basin of diesel oil to soak metal components and rinse plastic parts in fresh water. Once you have done this, dry the parts with cloths that do not leave residue.
Inspect gears, bearings, pins and pawls for any signs of wear or corrosion.
Carefully check the teeth of gears and ring gears to make sure there are no traces of wear.
Check the roller bearings and check there are no breaks in the bearing cages.
Replace worn or damaged components.
Carry out maintenance on components using the products listed below.
For more information on which products to use where, refer to the exploded diagram below.
Use a brush to lightly lubricate all gears, gear pins, teeth and all moving parts with grease.
Radial Winch 40.2 ST E/HY 18 Installation and Maintenance Manual
Lightly lubricate the pawls and springs with oil. Do not use grease on the pawls!
G
1
G
A
G
O
Anti-seize
Harken ® Grease
Harken ® Pawl Oil
A
A
A
A
G
2
G
G
G
G
G
O
G
G
O
G
1. Apply Harken ® grease on assy socket screw - 2. Apply Harken ® grease on drum gear
Radial Winch 40.2 ST E/HY 19 Installation and Maintenance Manual
Exploded view with maintenance products
Assembly
Make sure that the holes and drainage channels in the base of the winch are not obstructed.
Assemble the winch in the reverse order of the sequence in the section on disassembly.
When positioning the stripper arm, align the peeler with it.
OIL
If the jaws have been disassembled, insert peeler between the two jaws, taking care that the letters TOP on the peeler are facing upwards.
To assemble the pawls
Correctly position the spring in its housing as shown at left. Hold the spring closed and slide the pawl into its housing. Once in position, check that the pawls can be easily opened and closed with a finger.
NOTICE
Before screw the central screw, check the correct position of the o-ring in the assy socket.
To tighten bolts, use the torque indicated in the disassembly procedure.
Radial Winch 40.2 ST E/HY 20 Installation and Maintenance Manual
Harken
®
limited worldwide warranty - Ordering spare parts
In case of doubt concerning the assembly procedure contact Harken® Tech Service: [email protected]
Harken
®
limitedworldwidewarranty
Refer to the Harken ® Limited Worldwide
Warranty in the Harken ® Catalogue and on the website www.harken.com
Orderingspareparts
Spare parts can be requested from Harken ® as described in the Harken ® Limited Worldwide
Warranty, indicating the part number in the
Parts List and including the serial number of the winch for which the parts are required.
The serial number of the winch is printed on a plate on the drum support of the winch.
W XXXXX
XXXXXXXXX
Manufacturer
Harken
®
Italy S.p.A.
Via Marco Biagi, 14
22070 Limido Comasco (CO) Italy
Tel: (+39)031.3523511
Fax: (+39)031.3520031
Email: [email protected]
Web: www.harken.com
TechService
Email: [email protected]
CustomerService
Tel: (+39)031.3523511
Email: [email protected]
Headquarters
Harken
®
, Inc.
1251 East Wisconsin Avenue
Pewaukee, Wisconsin 53072-3755 USA
Tel: (262)691.3320
Fax: (262)691.3008
Email: [email protected]
Web: www.harken.com
Radial Winch 40.2 ST E/HY
TechService
Email: [email protected]
CustomerService
Tel: (262)691-3320
Email: [email protected]
21 Installation and Maintenance Manual
14
13
1
2
12
7
4
6
5
3
30
19
Exploded view
Explodedview
8
9
10
11
6
5
20
15
18
17
16
22
23
28
29
27
26
21
25
24
Radial Winch 40.2 ST E/HY 22 Installation and Maintenance Manual
30
19
14
13
1
2
12
7
4
6
5
3
8
9
10
11
6
5
20
Radial Winch 40.2 ST E/HY 23 Installation and Maintenance Manual
22
23
15
18
17
16
28
29
27
26
21
25
24
Parts lists
PartsList
Radial Winch 40.2 STA
A= drum in anodised aluminium
Pos.
Q.ty Code
1
2
3
4
5
6
7
8
9
10
11
12
Description
1 A 941896 00 Assy Base Winch 40 EL/HY
Base W40
Heli-coil M6x9
Roller Ø6x19
Bushing Ø22xØ25x8.5
Bushing Ø9xØ11x12*
Bushing Ø12xØ14x11*
1 A94141400 Assembly Skirt Winch 40
Skirt W40
Winch Product Sticker**
1 S 41302 00 04 Gear Z12
1 S 41303 00 04 Pawls Carrier Ø8xN2
4 S 00008 00 03 Pawl Ø8
4 S 00038 00 01 Pawl Spring Ø8
1 S 41283 00 41 Gear Z23
1 S 41300 00 04 Pin Ø9x55
1 S279090002 Washer 36x9,5x1*
1 S 41297 00 04 Gear Z20
1 S 41285 00 41 Pinion Z13
1 S 41312 00 02 Washer Ø22.5xØ45x1*
13
14
15
1 S 41307 00 04 Pin Ø9-Ø12x32.5
1
1
A94130500
A94141500
Assy Gear Z20
Gear Z20
Bushing Ø12xØ14x8*
Assy Housing W40
Support W40
Bushing Ø9xØ11x7*
Heli-coil M6x9
Bushing Ø22xØ25x8.5
Pos.
Q.ty Code
16
17
18
Description
6 M0635103 Socket head screw M6x16 UNI 5931*
1 S 41315 00 82 Washer Ø62xØ80x1.5*
2 A74136000 Bearing Ø56xØ68x24*
19
20
21
22
23
24
25
26
27
28
29
30
1 A94149800 Assy Central Shaft W40 EL/HY
Central Shaft Pred. W40
Washer Ø17.2xØ32x1.5
1 S 41876 00 63 Winch Serial Number Sticker
1 S 41294 00 A0 Stripper arm support
1 S414170053 Drum A W40
1 S281680097 Red line*
1 A94131800 Assy Winch 40 Jaws
Lower Jaw W40
Upper Jaw W40
Peeler W40
Spring
4 M0601803 Screw UNI EN ISO 1207:1996 - M6x35
- A4*
1 S 41420 00 19 Stripper Arm W35/40
3 M6007103 Screw M6x50 UNI6107*
1 A 941493 00 Assy Socket W40 EL/HY
Socket Handle W40
Washer ø25xø15x4
Nut Screw for Disconnect Rod
O ring RC 2025 series*
1 S 41419 00 A5 Cover 2 speed W40
1 S 41506 00 02 Disconnect Rod W40
*Service kit available; see winch kit section on the website www.harken.com
**Winch product sticker
Radial Winch 40.2 ST E/HY 24 Installation and Maintenance Manual
Radial Winch 40.2 STC
C=drum in chromed bronze
Pos.
Q.ty Code
1
2
3
4
5
6
7
8
9
10
11
Description
1 A 941896 00 Assy Base Winch 40 EL/HY
Base W40
Heli-coil M6x9
Roller Ø6x19
Bushing Ø22xØ25x8.5
Bushing Ø9xØ11x12*
Bushing Ø12xØ14x11*
1 A94141400 Assembly Skirt Winch 40
Skirt W40
Winch Product Sticker**
1 S 41302 00 04 Gear Z12
1 S 41303 00 04 Pawls Carrier Ø8xN2
4 S 00008 00 03 Pawl Ø8
4 S 00038 00 01 Pawl Spring Ø8
1 S 41283 00 41 Gear Z23
1 S 41300 00 04 Pin Ø9x55
1 S279090002 Washer 36x9,5x1*
1 S 41297 00 04 Gear Z20
1 S 41285 00 41 Pinion Z13
12
13
14
15
1 S 41312 00 02 Washer Ø22.5xØ45x1*
1 S 41307 00 04 Pin Ø9-Ø12x32.5
1
1
A94130500
A94141500
Assy Gear Z20
Gear Z20
Bushing Ø12xØ14x8*
Assy Housing W40
Support W40
Bushing Ø9xØ11x7*
Heli-coil M6x9
Bushing Ø22xØ25x8.5*
Pos.
Q.ty Code
16
17
Description
6 M0635103 Socket head screw M6x16 UNI 5931*
1 S 41315 00 82 Washer Ø62xØ80x1.5*
18
19
20
21
22
23
24
25
26
27
28
29
30
2 A74136000 Bearing Ø56xØ68x24*
1 A94149800 Assy Central Shaft W40 EL/HY
Central Shaft Pred. W40
Washer Ø17.2xØ32x1.5
1 S 41876 00 63 Winch Serial Number Sticker
1 S 41294 00 A0 Stripper arm support
1 S414180043 Drum C W40
1 S281680097 Red line*
1 A94131800 Assy Winch 40 Jaws
Lower Jaw W40
Upper Jaw W40
Peeler W40
Spring
4 M0601803 Screw UNI EN ISO 1207:1996 - M6x35
- A4*
1 S 41420 00 19 Stripper Arm W35/40
3 M6007103 Screw M6x50 UNI6107*
1 A 941493 00 Assy Socket W40 EL/HY
Socket Handle W40
Washer ø25xø15x4
Nut Screw for Disconnect Rod
O ring RC 2025 series*
1 S 41419 00 A5 Cover 2 speed W40
1 S 41506 00 02 Disconnect Rod W40
*Service kit available; see winch kit section on the website www.harken.com
**Winch product sticker
Radial Winch 40.2 ST E/HY 25 Installation and Maintenance Manual
Radial Winch 40.2 STCW
C=drum in chromed bronze W=components RAL 9003
Pos.
Q.ty Code
1
2
3
4
5
6
7
8
9
10
11
Description
1 A 941896 00 Assy Base Winch 40 EL/HY
Base W40
Heli-coil M6x9
Roller Ø6x19
Bushing Ø22xØ25x8.5
Bushing Ø9xØ11x12*
Bushing Ø12xØ14x11*
1 A 941414 00 W Assembly Skirt Winch 40 RAL 9003
Skirt W40 RAL 9003
Winch Product Sticker**
1 S 41302 00 04 Gear Z12
1 S 41303 00 04 Pawls Carrier Ø8xN2
4 S 00008 00 03 Pawl Ø8
4 S 00038 00 01 Pawl Spring Ø8
1 S 41283 00 41 Gear Z23
1 S 41300 00 04 Pin Ø9x55
1 S279090002 Washer 36x9,5x1*
1 S 41297 00 04 Gear Z20
1 S 41285 00 41 Pinion Z13
12
13
14
15
1 S 41312 00 02 Washer Ø22.5xØ45x1*
1 S 41307 00 04 Pin Ø9-Ø12x32.5
1
1
A94130500
A94141500
Assy Gear Z20
Gear Z20
Bushing Ø12xØ14x8*
Assy Housing W40
Support W40
Bushing Ø9xØ11x7*
Heli-coil M6x9
Bushing Ø22xØ25x8.5*
Pos.
Q.ty Code
16
17
Description
6 M0635103 Socket head screw M6x16 UNI 5931*
1 S 41315 00 82 Washer Ø62xØ80x1.5*
18
19
20
21
22
23
24
25
26
27
28
29
30
2 A74136000 Bearing Ø56xØ68x24*
1 A94149800 Assy Central Shaft W40 EL/HY
Central Shaft Pred. W40
Washer Ø17.2xØ32x1.5
1 S 41876 00 63 Winch Serial Number Sticker
1 S 41294 00 A0 Stripper arm support
1 S414180043 Drum C W40
1 S281680097 Red line*
1 A 941318 00 W Assy Winch 40 Jaws RAL 9003
Lower Jaw W40 RAL 9003
Upper Jaw W40 RAL 9003
Peeler W40 RAL 9003
Spring
4 M0601803 Screw UNI EN ISO 1207:1996 - M6x35
- A4*
1 S 41420 00 19 Stripper Arm W35/40
3 M6007103 Screw M6x50 UNI6107*
1 A 941493 00 Assy Socket W40 EL/HY
Socket Handle W40
Washer ø25xø15x4
Nut Screw for Disconnect Rod
O ring RC 2025 series*
1 S 41419 00 A5 W Cover 2 speed W40 RAL 9003
1 S 41506 00 02 Disconnect Rod W40
*Service kit available; see winch kit section on the website www.harken.com
**Winch product sticker
Radial Winch 40.2 ST E/HY 26 Installation and Maintenance Manual
Horizontal electric motor 12V/24V
3
Pos.
Q.ty Code
1
1
1
A 931279 00
A 941949 00
2
Description
KIT Gear Reduction VF49*
KIT LM Gear Reduction VF49**
1 A 941492 00 KIT Assy Electric Motor Flange
3
4
5
1
1
1 A 941495 00 KIT EL HO Motor Flange
1 A 941616 00 KIT EL HO Motor Clutch
A 960154 00
A 960157 00
KIT EL Motor 12V 0,7kW HO
KIT EL Motor 24V 0,9kW HO
4
2
1
Radial Winch 40.2 ST E/HY
5
*
Motor installed in right-hand configuration.
27
**
Motor installed in left-hand configuration.
Installation and Maintenance Manual

Public link updated
The public link to your chat has been updated.
Advertisement