Stahl ET-xx7 Operating instructions

Stahl ET-xx7 is a line of high-performance HMI devices designed for use in hazardous areas. These devices offer a range of features that make them ideal for use in a variety of applications, including process control, monitoring, and data acquisition. Stahl ET-xx7 devices are available in a variety of configurations, including panel PCs, thin clients, and KVM systems. All devices are designed to meet the highest safety standards and are backed by Stahl's commitment to quality and reliability. With its rugged construction and advanced features, Stahl ET-xx7 is the perfect choice for demanding applications in hazardous areas.

PDF Download

Document

Operating Instructions

Device platform MANTA

ET-xx7

SERIES 400 Panel PC

SERIES 500 Thin Clients

SERIES 600 KVM Systems

Doc. No.: 6000076

HW-Rev. ET-6x7:

HW-Rev. ET-4x7-*-BT:

HW-Rev. ET-5x7-*-BT:

HW-Rev. ET-4x7-*-P2:

HW-Rev. ET-5x7-*-P2:

Operating Instructions version:

Issue date:

Order number:

01.03.05

01.03.04

01.03.22

30.09.2021

296926

Operating Instructions ET-xx7 Disclaimer

Disclaimer

Publisher and copyright holder:

R. STAHL HMI Systems GmbH

Adolf-Grimme-Allee 8

D 50829 Köln

Telephone: (Sales Support)

Fax:

E-mail:

(Technical Support)

(Sales Support)

+49 221 768 06 - 1000

- 5000

- 4100 [email protected]

[email protected]

(Technical Support)



This document may not be reproduced in whole or in part except with the written consent of the publisher.



Subject to alterations.

Any warranty claims are limited to the right to demand amendments. Liability for any damage that might result from the contents of these instructions or all other documentation is limited to clear cases of premeditation.

We reserve the right to change our products and their specifications at any time, provided it is in the interest of technical progress. The information in the current manual (online or on CD / DVD

/ USB stick) or in the operating instructions included in the delivery applies.

Trademarks

The terms and names used in this document are registered trademarks and / or products of the companies in question.

Page 2 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Specific markings Operating Instructions ET-xx7

Specific markings

The markings in these operating instructions refer to specific features that must be noted.

In detail, these are:

DANGER

This sign alerts users to hazards that will result in death or serious injury if ignored !

WARNING

This sign alerts users to hazards that may result in death or serious injury if ignored !

CAUTION

This sign alerts users to hazards that may damage machinery or equipment or result in injury if ignored !

ATTENTION

Information highlighted by this symbol indicates measures for the prevention of damage to machinery or equipment !

NOTICE

Information highlighted by this symbol indicates important information of which particular note should be taken !

DOCUMENTATION

Information highlighted by this symbol (with and without lettering) refers to a different chapter or section in this manual or other documentation or a web-page !

Warnings

Caution !

In ambient temperatures exceeding +45 °C the surface of the devices may heat up. Caution when touching !

Caution !

The laser diodes installed in our Exicom operator devices, media converters and switches emit invisible laser radiation:

100Base-FX - 1300 nm

FO-MM / 1000Base-SX - 770 … 860 nm

FO-SM / 1000Base-LX -

1270 … 1355 nm

Acc. to EN 60825-1 the laser diode is classified as a class 1M laser / Do not view directly with optical instruments. The viewing of the laser beam through certain optical instruments (e.g. magnifying glasses, telescopes and microscopes) from a distance of less than 100 mm may damage eyesight. (beam output at the emitting diode (TD-A, TD-B) or the fibre optic end).



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 3 of 92

Operating Instructions ET-xx7 Table of contents

8.1

9.1

4.2.1

4.2.2

4.2.3

4.2.4

4.3

5.1

5.2

6.1

9.2

9.3

10.1

10.2

10.3

10.4

3.1

4.1

4.1.1

4.1.2

4.1.3

4.1.4

4.2

2.1

2.2

2.3

2.4

2.5

2.6

2.7

Page 4 of 92

Description

Disclaimer

Specific markings

Warnings

Table of contents

Preface

Device function

Image sticking

Processor types

Activation pressure touchscreen

ET-4x7 (SERIES 400 Panel PC)

ET-5x7 (SERIES 500 Thin Clients)

ET-6x7 (SERIES 600 KVM Systems)

Overview hardware revision

Type allocation

Type marking

Technical data

Additionally for ET-4x7 (Panel PC)

All devices up to hardware revision 01.03.00

All devices starting from hardware revision 01.03.01

All devices starting from hardware revision 01.03.03

ET-477 devices starting from hardware revision 01.03.04

Additionally for ET-5x7 (Thin Clients)

All devices up to hardware revision 01.03.00

All devices starting from hardware revision 01.03.01

All devices starting from hardware revision 01.03.03

ET-577 devices starting from hardware revision 01.03.04

Resolution at ET-6x7 (KVM Systems) with DVI3

Conformity to standards

CEC / NEC / CSA

Mounting inside enclosure

Certificates

FSB notification

Marking

Power supply

HMI devices

Permitted maximum values

External, non-intrinsically safe circuits

External inherently safe optical interface

External intrinsically safe circuits

Type code

ET-4x7 (Panel PC)

ET-4x7-*-BT (Panel PC)

ET-477-*-P2 (Panel PC)

ET-5x7 (Thin Client)

Page



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Table of contents Operating Instructions ET-xx7

12.1

12.2

12.3

13.1

13.2

14.1

14.2

14.2.1

14.2.1.1

14.2.1.2

14.2.2

14.2.2.1

14.2.2.2

10.5

10.6

10.7

11.1

11.2

11.3

11.3.1

11.3.2

11.3.3

11.3.4

11.3.4.1

11.3.4.2

11.4

11.5

11.6

14.2.3

14.2.4

14.2.5

14.2.6

14.2.7

14.3

ET-5x7-*-BT (Thin Client)

ET-577-*-P2 (Thin Client)

ET-6x7 KVM System

Safety information

General Safety Information

Cautionary note

Installation safety information

Only for HMI devices with DVI3 30

HMI installation in enclosures with degree of protection "e" or "t" 30

Conditions of safe use according to CEC / NEC / CSA 31

Tightening torque

Terminals

Cable glands

Industrial Security

Safety information for operation

Special conditions

Assembly and disassembly

General information

Cut-out ET-xx7

Tightening torque

Operation

General information

Connections

General Information

Touch driver

ET-4x7 (Panel PC) and ET-5x7 (Thin Client)

Up to Windows 7 operating systems

Licensing issues

Note on Windows Embedded operating systems

Windows® 10 IoT Enterprise 2019 LTSC operating system

Recovery

Company-specific Windows installations

Initial start-up ET-4x7 (Panel PC)

Recovery Stick

Back-up

Switching off / closing down

Data loss

Teaming function

Maintenance, overhaul

15.1

16.1

Damaged sealing

Troubleshooting

Repairs / hazardous substances

Disposal / Restricted substances

17.1

17.1.1

17.1.2

Declaration of substances and restricted substances

Declarable substance groups

RoHS directive 2011/65/EC

17.1.3

IMO Resolution MEPC.269(68)



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Page 5 of 92

Operating Instructions ET-xx7

18.1

18.2

21.1

21.2

21.3

21.4

21.4.1

21.4.2

Defective pixels

Terminology

Display specification ET-x77

Control Drawing CEC / NEC / CSA

Mounting inside enclosure with ET-xx7 mounting-set

Declarations of conformity

RCM

EAC

CCC

English version

Chinese version

Release notes

Table of contents

Page 6 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Preface Operating Instructions ET-xx7

1 Preface

These Operating Instructions contain all aspects relevant to explosion protection for the ET-xx7 devices - device platform MANTA - (SERIES 400 Open HMI - Panel PC´s, SERIES 500 Thin

Clients and SERIES 600 KVM Systems). They also contain information on the connection and installation (etc.) of these devices.

All data relevant to explosion protection from the EC-type examination certificate were copied into these operating instructions.

NOTICE

For the correct operation of all associated components please note, in addition to these operating instructions, all other operating instructions enclosed in this delivery as well as the operating instructions of the additional equipment to be connected !

DOCUMENTATION

Please note that all certificates of the HMI devices can be found in a separate document (CE_ET-xx7).

You can find this document in the internet at r-stahl.com

or request it from R. STAHL HMI Systems

GmbH.

2 Device function

The ET-xx7 units are explosion-protected equipment for installation in hazardous areas and can be operated in zones 1 and 21 with interfaces for zones 0/1/2 and 20/21/22.

The devices are connected to a communication system via the serial interfaces (RS-232,

Ethernet) located in their connection box at the rear. The connection box also contains the USB interfaces for the connection of various peripheral devices. Furthermore, the interfaces for keyboard, mouse, video and audio signals are also located here.

2.1 Image sticking

Continuous displaying fixed pattern may include image sticking. It’s recommended to use screen saver or moving content periodically if fixed pattern is displayed on the screen.

2.2 Processor types

All devices of 400 and 500 SERIES are fitted with modern, powerful processors. Depending on the type of application, different processor types are used for the HMI devices (see Technical

Data).

Starting in 2016, a new Intel® ATOM ™ processor type of the Bay Trail (BT) platform will gradually replace all previous processor types in the HMI devices, up from HW Revision

01.03.01. This new processor type processes data four times as fast as the previous processors.

In addition to the Bay Trail (BT) processor, the devices of 400 and 500 SERIES will be equipped with an AMD GX processor, up from HW Revision 01.03.04.

2.3 Activation pressure touchscreen

To prevent damage to the touchscreen, activation pressure on the screen with polyester foil must be very low (0.1 to max. 1 N) and on the screen with glass surface must be medium (1.8 to max. 2.5 N) !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 7 of 92

Operating Instructions ET-xx7 Device function

2.4 ET-4x7 (SERIES 400 Panel PC)

The ET-4x7 HMI panel PCs are intelligent display and operating devices which can run any software and are thus easy to operate.

The devices are fitted with powerful processors and are thus able to process even large applications on-site. The devices have a back-up and recovery system which can be used to save complete images and load them onto new Panel PCs without requiring specific IT skills.

The X13 interface is provided for this purpose.

2.5 ET-5x7 (SERIES 500 Thin Clients)

The ET-5x7 devices of the 500 SERIES can be integrated into modern networks as Thin Clients or with a KVM box via KVM-over-IP. Digital Ethernet technology is used for the data transfer between KVM box and Remote System.

Up to four ET-5x7 devices can access one KVM box with one software license, thus costeffectively communicating with several PCs - for example, when monitoring the production process and simultaneously applying Condition Monitoring.

Multi-monitoring with several on-site terminals can as easily be implemented as the application as Thin Client in a server environment with virtual work stations.

2.6 ET-6x7 (SERIES 600 KVM Systems)

The KVM Classic transfer technology is used for the point-to-point connection between a PC and an ET-6x7 KVM device.

There are three versions (DVI1, DVI2 and DVI3) of this transfer technology that have slightly different functionality.

2.7 Overview hardware revision

HW-Rev. Device type

Changing date hardware

OI version

OI date

01.02.00 ET-xx7-*

01.03.00 ET-xx7-*

01.03.01

01.03.02

01.03.03

ET-4x7-*-BT-*

ET-5x7-*-BT-*

ET-4x7-*-BT-*

ET-5x7-*-BT-*

ET-4x7-*-BT-*

ET-5x7-*-BT-*

01.03.04

01.02.05

ET-4x7-*-P2-*

ET-5x7-*-P2-*

ET-4x7-*-BT-*

ET-5x7-*-BT-*

ET-4x7-*-BT-*

ET-5x7-*-BT-*

ET-6x7-*

Technical changing

Changing from T-Ex to ET-xx7

NEC / CEC approval

Bay Trail processor, quad core

SX with TX

M.2 memory

AMD processor

GX-222GC

BIOS update

BIOS-V1.63r4 no C6

Changing cable glands

01.01.2013

12.12.2014

01.07.2016

15.01.2018

14.06.2018

31.03.2019

29.06.2021

01.02.00 17.04.2013

01.03.00 08.01.2015

01.03.02 04.01.2016

01.03.09 21.12.2017

01.03.11 29.08.2018

01.03.21 27.09.2021

Page 8 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Type allocation Operating Instructions ET-xx7

3 Type allocation

Since the beginning of 2013, the T-series devices have been allocated new type names according to the following pattern:

To avoid having to re-write certifications, the names in the certificates remain the same, but the devices receive new names.

In the interest of a clear link between device type and certificate, both device names are listed on the type plate from 01.04.2013 onwards.

3.1 Type marking

Old (certificate)

T-Ex-##*-CAT7*-R2

New

ET-##7*-TX* / ET-##7-2TX*

ET-##7*-CAT*

T-Ex-##*-MM*-R2

T-Ex-##*-SM*-R2

ET-##7*-MM* / ET-##7-SX*

ET-##7*-SM* / ET-##7-LX*

* = alphanumeric or symbolic characters without relevance to explosion protection.

# = numeric character without relevance to explosion protection.

NOTICE

For the exact new device name and model please refer to the type code.



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 9 of 92

Operating Instructions ET-xx7 Technical data

4 Technical data

Function / Equipment

Display type

Display size

Resolution in pixels

Format

Viewing angle

Horizontal

Vertical

Display

Touchscreen (optional)

Backlight

Service life (MTBF) of backlight at

20 °C / 68 °F

Brightness

Contrast

Anti-reflective display

Touchscreen activation

Touchscreen input method

Touchscreen durability

Touchscreen scratch hardness MoHS

Touchscreen scratch hardness pencil hardness test ISO 15184

Touchscreen transmissivity / optics

Touchscreen surface contaminants

Touchscreen abrasive resistance

Additional keyboard (optional)

Power supply

Rated operational voltage AC

Voltage range AC

Frequency range

Rated operational voltage DC

Voltage range DC

Power

Current consumption AC

Current consumption DC

Connections

Recommended fuses

Max. operating voltage Um

ET-467

ET-567

ET-667

56 cm (22")

WSXGA+ 1680 x 1050

16:10 at CR ≥ 5

178°

170°

ET-477

ET-577

ET-677

TFT Color display

16.7 million colours

61 cm (24")

Full HD 1920 x 1080

16:9 at CR ≥ 5

178°

170°

Glass

Polyester foil or glass surface

5-wire analogue resistive

LED background lighting

Typically 50,000 h

ET-487

ET-587

ET-687

61 cm (24"WU)

WUXGA 1920 x 1200

16:10 at CR ≥ 10

178°

250 cd/m² 300 cd/m²

1000 : 1

Devices without touchscreen: chemically coated

Devices with foil touchscreen: lightly anti-reflective (foil is abraded for slight milky effect)

Device with glass touchscreen: not anti-reflective, glass is too thin for chemical or mechanical treatment

Foil touch: low activation pressure (0.1 up to max. 1 N)

Glass touch: medium activation pressure (1.8 up to max. 2.5 N)

Finger, gloved finger or stylus

Foil touch: Polyester foil is easily scratched, with high pressure force the spacer dots could be damaged.

Glass touch: Quite good, but with high pressure force the spacer dots could be damaged.

Foil touch: -

Glass touch: >5

Foil touch: 3H

Glass touch: 9H

Foil touch: small milky effect due to the foil

Glass touch: very good

Unaffected

36 million times with a silicone rubber of R8 finger, hitting rate 250 g at 2 times per second

107 keys with integrated trackball / joystick / mouse pad or touch pad

Directly in the integrated Ex e connection box

230 V

100 - 240 V

50 - 60 Hz

24 V

20 - 30 V

Typically 50 W / 100 W at O30 / max. 150 W

(typically 170 BTU / 341 BTU at O30 / max. 510 BTU)

1 A

3 A via screw terminals, green

Flexible cable up to 2.5 mm² (AWG14)

Fixed cable up to 4 mm² (AWG12)

4 AT

250 VAC

Page 10 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Technical data Operating Instructions ET-xx7

Interfaces

Ethernet at ET-4x7 and ET-5x7

Optical fibre (SX)

Optical fibre (LX)

* Note optical fibre (SX and

LX) at ET-6x7

Copper (CAT)

Optical fibre (FO) (MM / SM)

USB

Note on USB interfaces

Serial

Video in (optional)

Audio

Audio sound (optional)

Voltage output

** Note

Only for ET-4x7 and ET-5x7

Real-time clock

Data buffer

Battery

Capacitor

Cable type optical fibre

SX or MM

LX or SM

Data cable lengths

Optical fibre

SX or MM

LX or SM

Copper (TX)

Copper (CAT) for DVI1 for DVI2 for DVI3

Note CAT cable

Enclosure

Enclosure protection type

HMI Types

HMI Types comment

Cable glands

Type *

Number

Thread size

Cable diameter range

Width across flats

Mounting version keyboards

* Comment

* Comment a

Either copper or optical fibre * for information on copper, see sections 4.1 and 4.2

1000Base-SX, 1000 Mbit, multi-mode, intrinsically safe (Ex op is)

1000Base-LX, 1000 Mbit, single mode, intrinsically safe (Ex op is)

Up from HW-Rev. 01.03.02, all ET-4x7 and ET-5x7 devices with SX or LX Ethernet interface are fitted additional with an Ethernet 10/100/1000Base-TX interface !

Direct connection, Gigabit

Direct connection

2x Ex ia; 1x Ex e / USB 2.0, 480 Mbit/s for keyboard and mouse (Ex ia) / USB 2.0, 480 Mbit/s

The USB interfaces are based on USB 2.0. Due to explosion protection rules, the USB interface properties (such as speed or power supply) may be restricted.

RS-232, (Ex e)

FBAS (Ex e) (not AMD version)

Line out interface (Ex e) (Line in only at ET-6x7)

Audio amplifier (mono amplifier) 3.5 W, for 2x loudspeaker connection (Ex e)

(not AMD version)

12 VDC, max. 500 mA **

The voltage output has an internal fuse that cannot be replaced ! yes

Lithium battery and capacitor buffered, maintenance-free

> 5 years at least 4 days

Multi-mode optical fibre cable (50 µm core cross section and 125 µm external cross section)

Multi-mode optical fibre cable (62.5 µm core cross section and 125 µm external cross section)

Single mode optical fibre cable (9 µm core cross section and 125 µm external cross section) up to 550 m (1,804 ft) via 50/125 μm optical fibre cable up to 275 m (902 ft) via 62.5/125 μm optical fibre cable up to 10,000 m (33,000 ft) via 9/125 μm optical fibre cable up to 100 m (330 ft) via CAT7 installation cable AWG23 at 1x TX

2x up to 100 m (330 ft) via CAT7 installation cable AWG23 at 2TX up to 140 m (460 ft) via CAT7 installation cable AWG23 up to 500 m (1,640 ft) via CAT7 installation cable AWG23 up to 150 m (492 ft) via CAT7 installation cable AWG23

Minimum requirement is CAT5e, CAT7 recommended

Steel

Front IP66 / back IP65

PM = PanelMount = panel mount device

OS = Operator Station

Panel mount device (PM): devices without additional enclosure (HSG) and without additional accessories

Operator Station (OS): devices mounted inside additional enclosure (HSG)

HSK-M-Ex (Ex e)

2 x M16 / 1 x M20 / 3 x M25

M16 x 1.5 / M20 x 1.5 / M25 x 1.5

1x M16 = 4 … 8 mm / 1x M16 = 5 … 10 mm / M20 = 7 … 13 mm / M25 = 14 … 18 mm

M16 = SW20 / M20 = SW24 / M25 = SW30 when wiring KBDiUSB, use the cable glands 2x M16 4… 8 mm

(1x enclosed loose, exchange it for 1x M16 5… 10 mm) when wiring KB2, use the cable gland

1x M16 5… 10 mm (is pre-assembled)

Similar certified cable glands may be used.

Not used cable glands must be closed by certified screw plugs or stopping plugs !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 11 of 92

Operating Instructions ET-xx7 Technical data

Permitted ambient temperature range

Operating temperature range

Cold start temperature *

Operation **

Operation with heater version O30 ***

Storage temperature range

* Note on cold start temperature

** Note on operation

*** Note on the O30 version

HMI Types comment OS

-30 °C … +60 °C / [-22 °F … +140 °F]

-10 °C / [+14 °F]

-20 °C … +60 °C / [-4 °F … +140 °F]

-30

°C … +60 °C / [-22 °F … +140 °F]

-30

°C … +70 °C / [-22 °F … +158 °F]

If the device is switched on in an ambient temperature of below -10 °C / [+14 °F], the display will require some time warming up before everything is clearly visible. Depending on how low the actual temperature is, this process may take up to 3 hours.

Operation at +60 °C / [+140 °F] for a maximum of 5 hours, at +50 °C / [+122 °F] for continuous operation (24/7)

The O30 version is only available for the AC version devices ! (not AMD version)

If the HMI device is installed in an additional enclosure (HSG), the upper temperature limit is reduced by 5 °C / [41 °F], due to the device's own heating and lower temperature dissipation in the additional enclosure !

Thus, the operator stations offers "only" an operation temperature range of

-20 °C … +55 °C / [-4 °F … +131 °F] !

Operating temperature range for DVI1

Cold start temperature

Operation

Storage temperature range

Heat dissipation

Relative humidity for DVI1

Environmental conditions

+5 °C [+41 °F]

°C … +40 °C / [+41 °F … +104 °F]

-20

°C … +70 °C / [-4 °F … +158 °F]

About 40 % via the front plate and 60 % via the enclosure

10 to 90 % at +40 °C / [+104 °F], non-condensing

20 to 80 % at +40 °C / [+104 °F], non-condensing

Valid for all devices

Level Test specification

Damp heat (cyclic)

(only device with glass touch (TG))

Dry heat

+55 °C (±2 °C) ≥95 % IEC 60068-2-30 : 2005

+65 °C

IEC 60068-2-2 : 2007

IEC 60068-2-78 : 2012

Vibration (sinus) 5 up to 13.2 Hz: ±1 mm

13.2 up to 100 Hz: ±0.7 g

Sweep cycle 1 oct/min

Axis X, Y, Z

71.7 up to 79.2 Hz: ±0.7 g

120 min.

Sweep cycle 1 oct/min

Axis X

30 Hz: ±0.7 g

90 min.

Sweep cycle 1 oct/min

Axis Y, Z

IEC 60068-2-6 : 2008

Dwell test

Dimensions

Front (w x h)

Cut-out

(w x h) (+/-0.5 mm) (0.002")

Depth of cut-out

Wall thickness

Cut-out dimension for rear mount module

(w x h)

475.7 mm x 298.1 mm

660 mm x 475 mm (25.98” x 18.70”)

615 mm x 435 mm (24.21” x 17.13”)

110 mm (4.33")

≤5 mm (0.02")

523 mm x 295 mm

(18.73" x 11.74")

Mounting position

Weight

4.1 Additionally for ET-4x7 (Panel PC)

(20.59" x 11.61")

Vertical or horizontal

32.00 kg (70.55 lbs)

520.4 mm x 326 mm

(20.49" x 12.83")

4.1.1 All devices up to hardware revision 01.03.00

Processor

RAM

Data memory

Type of data memory

Operating system

Global language support

Interface copper (TX)

Intel ATOM N270; 1.6 GHz

1 or 2 GB

4 or 16 GB

128 GB MLC

128 GB SLC

Flash memory (SATA)

Windows XP Embedded / Windows XP Professional / Windows 7 Ultimate (32 bit)

Via Multi-Language interface of Windows XP Embedded (25 languages)

1x 10/100Base-TX, 10/100 Mbit (Ex e)

Page 12 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Technical data Operating Instructions ET-xx7

4.1.2 All devices starting from hardware revision 01.03.01

Processor

RAM

Data memory

Type of data memory

Graphics controller

Operating system

Global language support

Interface copper (TX)

Note copper

Intel Bay Trail (BT) ATOM E3845 Quad Core; 1.91 GHz

4 GB

Size

64 GB MLC

TBW

18.75

Test profile

JESD218 Client profile

128 GB MLC 37.5

Flash memory (Solid state drive - SSD) (internal via CF-Slot)

Integrated Intel Gen. 7 HD Graphics

Windows Embedded Standard 7 (64 bit) / Windows 7 Ultimate (64 bit)

Via Windows operating system

1x 10/100Base-TX, 10/100 Mbit (Ex e) or

2x 10/100Base-TX, 10/100 Mbit (Ex e)

If the customer installs an operation system, the driver for the "USB-SK-LAN-Adapter" must be installed. For this, please contact [email protected]

(Driver is part of STAHL images)

4.1.3 All devices starting from hardware revision 01.03.03

Type of data memory

Operating system

Flash memory M.2 (Solid State Drive - SSD) (internal via SATA)

Windows 10 IoT Enterprise (64 bit) (included in standard delivery)

Windows 10 IoT Enterprise (32 bit) (optional on USB stick)

4.1.4 ET-477 devices starting from hardware revision 01.03.04

Processor type

Processor details

Graphics controller

Interface copper (TX)

AMD GX-222GC

2.2 GHz; Dual Core, 10W TDP i ntegrated AMD Radeon R5E graphics

1x 10/100Base-TX, 10/100 Mbit (Ex e) or

2x 10/100Base-TX, 10/100 Mbit (Ex e)

4.2 Additionally for ET-5x7 (Thin Clients)

4.2.1 All devices up to hardware revision 01.03.00

Processor

RAM

Data memory

Operating system

Interface copper (TX)

NOTICE

AMD Geode LX 800; 266 MHz

512 MB

2 GB *

1 GB

16 GB *

Windows Embedded Standard 2009 and Remote Firmware

Windows Embedded Standard 7, Remote Firmware and Delta V *

1x 10/100Base-TX, 10/100 Mbit (Ex e)

* The combination of 2 GB RAM with 16 GB data memory is only available for the operating system with Delta V !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 13 of 92

Operating Instructions ET-xx7 Technical data

4.2.2

Processor

RAM

Data memory

Type of data memory

Graphics controller

Operating system

Interface copper (TX)

Note copper

All devices starting from hardware revision 01.03.01

Size

Intel Bay Trail (BT) ATOM E3845 Quad Core; 1,91 GHz

4 GB

64 GB MLC

TBW

18.75

Test profile

JESD218 Client profile

128 GB MLC 37.5

Flash memory (SATA)

Integrated Intel Gen. 7 HD Graphics

Windows 10 IoT Enterprise and Remote Firmware

1x 10/100Base-TX, 10/100 Mbit (Ex e) or

2x 10/100Base-TX, 10/100 Mbit (Ex e)

If the customer installs an operation system, the driver for the "USB-SK-LAN-Adapter" must be installed. For this, please contact [email protected]

(Driver is part of STAHL images)

4.2.3 All devices starting from hardware revision 01.03.03

Type of data memory

4.2.4

Flash memory M.2 (Solid State Drive - SSD) (internal via SATA)

ET-577 devices starting from hardware revision 01.03.04

Processor type

Processor details

Graphics controller

Interface copper (TX)

AMD GX-222GC

2.2 GHz; Dual Core, 10W TDP i ntegrated AMD Radeon R5E graphics

1x 10/100Base-TX, 10/100 Mbit (Ex e) or

2x 10/100Base-TX, 10/100 Mbit (Ex e)

4.3 Resolution at ET-6x7 (KVM Systems) with DVI3

Function / Equipment

Resolution in pixels

ET-667

1680 x 1050

1280 x 1024

1280 x 960

1152 x 864

1024 x 768

800 x 600

ET-677

1920 x 1080

1600 x 1200

1600 x 1000

1400 x 1050

1360 x 768

1280 x 1024

1280 x 920

1280 x 800

1152 x 864

1024 x 768

800 x 600

ET-687

1920 x 1200

1920 x 1080

1680 x 1050

1600 x 1200

1280 x 1024

1280 x 960

1280 x 800

1152 x 864

1024 x 768

800 x 600

Page 14 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Conformity to standards Operating Instructions ET-xx7

5 Conformity to standards

The ET-xx7 devices comply with the following standards and directive:

Standard

2. Supplement

Classification

ATEX directive 2014/34/EU

EN 60079-0 : 2009

EN 60079-5 : 2007

EN 60079-7 : 2007

General requirements

Powder filling "q"

Increased safety "e"

EN 60079-11 : 2007

EN 60079-26 : 2007

EN 60079-28 : 2004

EN 60079-31 : 2009

Intrinsic safety "i"

Device protection (EPL) "Ga"

Optical radiation

Protected by enclosures "tD" (dust)

EN 61241-11 : 2006 Intrinsic safety "iD" (dust)

The product corresponds to requirements from:

EN 60079-0 : 2012 + A11 : 2013

EN IEC 60079-0 : 2018

EN 60079-5 : 2015

EN 60079-7 : 2015

EN IEC 60079-7 : 2015 + A1 : 2018

General requirements

Powder filling "q"

Increased safety "e"

EN 60079-11 : 2012

EN 60079-26 : 2015

EN 60079-28 : 2016

EN 60079-31 : 2014

Intrinsic safety "i"

Device protection (EPL) "Ga"

Optical radiation

Protected by enclosures "tD" (dust)

Electromagnetic compatibility

EMV directive

2014/30/EU

EN 61000-6-2 : 2006

EN 61000-6-4 : 2007

EN 61010-1 : 2001+

EN 62368-1 : 2016

IEC 62368-1 : 2014

Classification

Interference resistance

Interference emission

Low voltage directive

Directive 2014/35/EU

General requirements

Audio / video, information and communication technology equipment - Safety requirements

RoHS directive

2011/65/EU

EN IEC 63000 : 2018

Classification

Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 15 of 92

Operating Instructions ET-xx7 Conformity to standards

5.1 CEC / NEC / CSA

Standard

CAN/CSA-C22.2 No. 0-10

August 2011

CAN/CSA-C22.2 No. 61010-1-12

CAN/CSA-C22.2 No. 60079-0 : 11

(December 2011)

CAN/CSA-C22.2 No. 60079-5 : 11

(December 2011)

CAN/CSA-C22.2 No. 60079-7 : 12

(February 2012)

CAN/CSA-C22.2 No. 60079-11 : 11

(December 2011)

CAN/CSA-C22.2 No. 60529:05

(Reaffirmed 2010)

ANSI/UL 61010-1

(2012)

ANSI/UL 60079-0

(sixth edition July 2013)

ANSI/UL 60079-5

(third edition November 2013)

ANSI/UL 60079-7

(fourth edition May 2013)

ANSI/UL 60079-11

(sixth edition March 2014)

ANSI/IEC 60529-2004

Classification

General requirements

Canadian Electrical Code, Part II

Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory

Use - Part 1: General Requirements

(Third Edition)

Explosive atmospheres

– Part 0: Equipment

General requirements

Explosive atmospheres – Part 5: Equipment protection by powder filling “q”

Explosive atmospheres – Part 7: Equipment protection by increased safety “e”

Explosive atmospheres – Part 11: Equipment protection by intrinsic safety “i”

Degrees of protection provided by enclosures

(IP Code)

Electrical Equipment for Measurement,

Control, and Laboratory Use - Part 1: General

Requirements (Third Edition)

Explosive atmospheres –

Part 0: Equipment – General requirements

Explosive atmospheres –

Part 5: Equipment protection by powder filling “q”

Explosive atmospheres

–

Part 7: Equipment protection by increased safety “e”

Explosive atmospheres –

Part 11: Equipment protection by intrinsic s afety “i”

Degrees of protection provided by enclosures

(IP code)

5.2 Mounting inside enclosure

The ET-xx7 devices can be mounted in an enclosure with suitable cut-out using an mounting kit.

This mounting kit is approved for mounting in an Ex e, Ex p or Ex tb protected enclosure and consist of a sealing fixed at the HMI device and 24 nuts.

The assembly is shown in drawing “10410300 T-Ex - xx7 Mounting Assembly Overview”.

The sealing must be in correct position and must not be damaged.

The nuts must be mounted with a torque of 1.0 Nm ... 1.4 Nm.

Page 16 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Certificates Operating Instructions ET-xx7

6 Certificates

The ET-xx7 devices are certified for installation in the following areas:

Synonym Scope Certificate number

CE / ATEX Europe BVS 11 ATEX E 102 X

IECEx

EAC

NEC

CEC

Global

Russia

USA

Canada

IECEx BVS 11.0075X

TC RU C-DE.HA91.B.00166/20

CSA 70011698

PESO

CCE

India

A/P/HQ/TN/104/5768 (P438244)

P438244/1

KCC

KGS

CCC

CNEX

RCM

DNV / GL

Korea

China

Australia

Marine- / ship certification

12-GA4BO-0617X

2021312309000500

CNEx21.1938X

TAA00000BK

Comment see notice CEC

Identification number

Device restriction see notice

KCC

According to declaration of conformity

Device restriction see notice

DNV / GL

DOCUMENTATION

You can access all IECEx certificates on the official website of the IEC under their certificate number. http://iecex.iec.ch/iecex/iecexweb.nsf/welcome?openform

NOTICE

Note CEC:

The HMIs are certified according to Ex e q [ia] IIC T4 Gb.

According to the CEC Part 1 each device with these protection types may be operated in Class I, Division 2 areas.

For more details on this, please refer to the CEC.

NOTICE

Note KCC:

In order to be able to operate these HMI devices in Korea, each device type additionally requires a KCC certificate.

Actually the following devices has such a certificate:

T-Ex-22 (ET-x67), T-Ex-22-DVI3 (ET-667-DVI3), T-Ex-24T (ET-x77 with touch screen (foil))

NOTICE

Note DNV / GL:

Only the HMI devices type:

ET-667-DVI3-yM-FO-TFT-TG-AC-O30-AL

ET-677-DVI3-yM-FO-TFT-TG-AC-O30-AL

ET-687-DVI3-yM-FO-TFT-TG-AC-O30-AL have DNV / GL certification! with y: M = FO direct connection multi-mode

S = FO direct connection single mode



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 17 of 92

Operating Instructions ET-xx7 Marking

6.1 FSB notification

The FSB notification of the MANTA field systems can be reviewed under this link: https://portal.eaeunion.org/sites/odata/_layouts/15/Portal.EEC.Registry.Ui/DirectoryForm.aspx?ViewId=859e c98d-f4fe-423a-b6bc-d01b53fd4b7c&ListId=0e3ead06-5475-466a-a340-

6f69c01b5687&ItemId=232#f=STAHL

7 Marking

Manufacturer

Type code

CE classification:

Testing authority and certificate number:

Ex classification:

ATEX

IECEx

EAC

NEC

R. STAHL HMI Systems GmbH

ET-4x7 / ET-5x7 / ET-6x7 c

0158

BVS 11 ATEX E 102 X

CEC

PESO

KGS

CCC / CNEX e

II 2(1) G Ex eb q [ia op is Ga] IIC T4 Gb

II 2(1) D Ex tb IIIC [ia op is Da] IP65 T110°C Db

Ex eb q [ia op is Ga] IIC T4 Gb

Ex tb IIIC [ia op is Da] IP65 T110°C Db

1Ex e q [ia op is Ga] IIC T4 Gb X

Ex tb IIIC [ia op is Da] T110°C Db X

Class I, Zone 1 AEx e q [ia] IIC T4 Gb

Class I, Division 2, Groups A, B, C, D

(according to NEC 501.5)

Ex e q [ia] IIC T4 Gb

Class I, Division 2, Groups A, B, C, D

(according to CEC J18-150)

Ex eb q [ia op is Ga] IIC T4 Gb

Ex e q IIC T4

Ex tb IIIC IP64 T110°C

Ex ia IIC T4

Ex ia IIIB T110°C

Ex e q [ia op is Ga] IIC T4 Gb

Ex tD [iaD op is] A21 IP65 T110°C

Page 18 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Power supply Operating Instructions ET-xx7

8 Power supply

8.1 HMI devices

Power supply: 24 VDC or 100 – 240 VAC, 50 – 60 Hz max. power consumption: at 24 VDC at 100 - 240 VAC max. 3 A max. 1 A

9 Permitted maximum values

9.1 External, non-intrinsically safe circuits

Input voltage “PWR” (X10):

Nominal voltage:

Power consumption I max

Power P max

Max. operating voltage U m

Short-circuit current I

USB (X13):

Rated voltage

Max. operating voltage U m

12 V (X14):

Rated voltage

Power consumption Imax

Max. operating voltage U m

RS-232 "SER" (X97):

20 ...240 VAC/VDC (depending on type)

≤ 5 A

≤ 150 W

≤ 250 VAC

≤ 1500 A

5 VAC/VDC (±10 %)

≤ 250 VAC

12 VAC/VDC (±10 %)

≤ 400 mA

≤ 250 VAC

Rated voltage

Max. operating voltage U m

Video "CAM" (X101):

Rated voltage

Max. operating voltage U m

Audio "AUD" (X105):

15 VAC/VDC (±10 %)

≤ 250 VAC

5 VAC/VDC (±10 %)

≤ 250 VAC

Rated voltage

Max. operating voltage U m

Copper Ethernet (CAT7 1) (X16):

Rated voltage

Max. operating voltage U m

100 VAC/VDC (±10 %)

≤ 250 VAC

5 VAC/VDC (±10 %)

≤ 250 VAC



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 19 of 92

Operating Instructions ET-xx7 Permitted maximum values

9.2 External inherently safe optical interface

Ethernet optical fiber (FO 1) (X18)

Multi-mode

Wavelength

Radiant power max. radiant power:

850 nm

0.22 mW

35 mW

Single mode

Wavelength

Radiant power max. radiant power:

1310 nm

0.22 mW

35 mW

9.3 External intrinsically safe circuits

Keyboard (X11)

The maximum values are:

I i i

P i

C i

L i

5.5

= negligible

µF mH

Pointer device (X12):

The maximum values are:

U i

I i

P i

C i

L i

5.5

= negligible

µF mH

USB1i (X24):

The maximum values are:

U i

I i

P i

C i

L i

5.5

= negligible

µF mH

USB2i (X25):

The maximum values are:

U i

= 5.5

I i

P i

C i

L i

= negligible µF

= negligible mH

U o

= 5.5 l o

= 309

P o

= 629

C o

= 50

L o

= 40

U o

= 5.5 l o

= 309

P o

= 629

C o

= 50

L o

= 40

U o

= 5.5 l o

= 309

P o

= 629

C o

= 50

L o

= 40

U o

= 5.5 l o

= 309

P o

= 629

C o

= 50

L o

= 40

V mA mW

µF

µH

V mA mW

µF

µH

V mA mW

µF

µH

V mA mW

µF

µH

Page 20 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Type code Operating Instructions ET-xx7

10 Type code

10.1 ET-4x7 (Panel PC)

NOTICE

These versions apply to all Panel PC's up to hardware revision

01.03.00, with ATOM N270 processor.

ET-4x7-aa-bb-cc-dd-ee-ff-gg-hh

Device variant:

Classification product key

ET-4x7SX -bb-cc-dd-ee-ff-gg-hh

ET-4x7TX

ET-4x7-aa-

-bb-cc-dd-ee-ff-gg-hh

TFT

ET-4x7-aa-bbT

-cc-dd-ee-ff-gg-hh

-dd-ee-ff-gg-hh

ET-4x7-aa-bbTG -dd-ee-ff-gg-hh

ET-4x7-aa-bb-ccR1 -ee-ff-gg-hh

ET-4x7-aa-bb-ccR2 -ee-ff-gg-hh

ET-4x7-aa-bb-cc-dd4GB -ff-gg-hh

ET-4x7-aa-bb-cc-dd16GB -ff-gg-hh

ET-4x7-aa-bb-cc-dd128GBM -ff-gg-hh

ET-4x7-aa-bb-cc-dd128GBS -ff-gg-hh

Front design

Outdoor option

Voltage supply

Data memory

RAM

Touch screen

Display type

Ethernet interface

467 / 477 / 487 middle digit = display size

6 = 56 cm / 22" display

7 = 61 cm / 24" display

8 = 61 cm / 24"WU display

Description

Type with

Optical fiber Ethernet interface 1000Base-SX

(Ex op is), multi-mode

Copper Ethernet interface 10/100Base-TX (Ex e)

TFT display (standard)

Touch screen (membrane)

Touch screen glass

1 GB RAM

2 GB RAM

4 GB Solid State Drive

16 GB Solid State Drive

128 GB Solid State Drive MLC

128 GB Solid State Drive SLC

100 GB hard disk (internal) ET-4x7-aa-bb-cc-dd100GB -ff-gg-hh

ET-4x7-aa-bb-cc-dd-eeAC -gg-hh

ET-4x7-aa-bb-cc-dd-eeDC -gg-hh

ET-4x7-aa-bb-cc-dd-ee-ffO30 -hh

ET-4x7-aa-bb-cc-dd-ee-ff-ggAL

ET-4x7-aa-bb-cc-dd-ee-ff-ggRM

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Outdoor installation -30 °C [-22 °F] *

Aluminium front plate

Rear mount module

NOTICE * The O30 option is only available for AC devices !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 21 of 92

Operating Instructions ET-xx7 Type code

**10.2 ET-4x7-*-BT (Panel PC)**

NOTICE

These versions apply to all Panel PC's starting from hardware revision 01.03.01, with Bay Trail ATOM E3845 processor.

ET-4x7-aa-BT-bb-cc-dd-ee-ff-gg-hh-ii

Device variant:

Classification product key

ET-4x7SX -BT-bb-cc-dd-ee-ff-gg-hh-ii

Front design

Outdoor option

Voltage supply

Audio

Data memory

RAM

Touch screen

Display type

Processor type (fixed to BT = Bay Trail)

Ethernet interface

467 / 477 / 487 middle digit = display size

6 = 56 cm / 22" display

7 = 61 cm / 24" display

8 = 61 cm / 24"WU display

ET-4x7LX -BT-bb-cc-dd-ee-ff-gg-hh-ii

ET-4x7TX -BT-bb-cc-dd-ee-ff-gg-hh-ii

ET-4x72TX -BT-bb-cc-dd-ee-ff-gg-hh-ii

ET-4x7-aa-BTTFT -cc-dd-ee-ff-gg-hh-ii

ET-4x7-aa-BT-bbT -dd-ee-ff-gg-hh-ii

ET-4x7-aa-BT-bbTG -dd-ee-ff-gg-hh-ii

ET-4x7-aa-BT-bb-ccR3 -ee-ff-gg-hh-ii

ET-4x7-aa-BT-bb-cc-dd64GB -ff-gg-hh-ii

ET-4x7-aa-BT-bb-cc-dd128GB -ff-gg-hh-ii

ET-4x7-aa-BT-bb-cc-dd-eeSND -gg-hh-ii

ET-4x7-aa-BT-bb-cc-dd-ee-ffAC -hh-ii

ET-4x7-aa-BT-bb-cc-dd-ee-ffDC -hh-ii

ET-4x7-aa-BT-bb-cc-dd-ee-ff-ggO30 -ii

ET-4x7-aa-BT-bb-cc-dd-ee-ff-gg-hhAL

ET-4x7-aa-BT-bb-cc-dd-ee-ff-gg-hhRM

NOTICE

Description

Type with

Optical fiber Ethernet interface 1000Base-SX

(Ex op is), multi-mode

Additional with 1x copper Ethernet interface

10/100/1000Base-TX up from HW-Rev. 01.03.02

Optical fiber Ethernet interface 1000Base-LX

(Ex op is), single mode

Additional with 1x copper Ethernet interface

10/100/1000Base-TX up from HW-Rev. 01.03.02

Copper Ethernet interface 10/100Base-TX

(Ex e)

2x Copper Ethernet interface 10/100Base-TX

(Ex e)

TFT display (standard)

Touch screen (membrane)

Touch screen glass

4 GB RAM

64 GB Solid State Drive

128 GB Solid State Drive

Audio amplifier (mono amplifier) 3.5 W

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Outdoor installation -30 °C [-22 °F] *

Aluminium front plate

Rear mount module

* The O30 option is only available for AC devices !

Page 22 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Type code Operating Instructions ET-xx7

**10.3 ET-477-*-P2 (Panel PC)**

NOTICE

ET-477-aa-P2-bb-cc-dd-ee-ff-gg-hh-ii

Device variant:

Classification product key

ET-4772TX -P2-bb-cc-dd-ee-ff-gg-hh-ii

ET-477-

These versions apply to all Panel PC's starting from hardware revision 01.03.04, with AMD GX processor.

-P2-bb-cc-dd-ee-ff-gg-hh-ii

ET-477-aa-P2TFT

ET-477-aa-P2-bb-

-cc-dd-ee-ff-gg-hh-ii

-dd-ee-ff-gg-hh-ii

TG -dd-ee-ff-gg-hh-ii

ET-477-aa-P2-bb-ccR3 -ee-ff-gg-hh-ii

ET-477-aa-P2-bb-cc-dd64GB -ff-gg-hh-ii

ET-477-aa-P2-bb-cc-dd128GB

ET-477-aa-P2-bb-cc-dd-ee-ff-

-ff-gg-hh-ii

-hh-ii

ET-477-aa-P2-bb-cc-dd-ee-ff-gg-hhAL

Front design

Outdoor option

Voltage supply

Audio

Processor type (P2 = AMD GX)

(unavailable)

Data memory

RAM

Touch screen

Display type middle digit

(unavailable)

Ethernet interface

display size

61 cm / 24" display

Description

Type with

2x Copper Ethernet interface 10/100Base-TX

(Ex e)

Optical fiber Ethernet interface 1000Base-SX

(Ex op is), multi-mode, additional 1x copper Ethernet interface

10/100/1000Base-TX

Optical fiber Ethernet interface 1000Base-LX

(Ex op is), single mode, additional 1x copper Ethernet interface

10/100/1000Base-TX

TFT display (standard)

Touch screen (membrane)

Touch screen glass

4 GB RAM

64 GB Solid State Drive

128 GB Solid State Drive

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Aluminium front plate



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 23 of 92

Operating Instructions ET-xx7 Type code

10.4 ET-5x7 (Thin Client)

NOTICE

These versions apply to all Thin Client's up to hardware revision

01.03.00, with AMD Geode LX processor.

ET-5x7-aa-bb-cc-dd-ee-ff

Device variant:

Classification product key

ET-5x7SX -bb-cc-dd-ee-ff

Front design

Outdoor option

Voltage supply

Touch screen

Display type

Ethernet interface

567 / 577 / 587 middle digit = display size

6 = 56 cm / 22" display

61 cm / 24" display

61 cm / 24"WU display

Description

Type with

Optical fiber Ethernet interface 1000Base-SX (Ex op is), multi-mode

Copper Ethernet interface 10/100Base-TX (Ex e)

TFT display (standard)

ET-5x7TX -bb-cc-dd-ee-ff

ET-5x7-aaTFT -cc-dd-ee-ff

ET-5x7-aa-bbT -dd-ee-ff

ET-5x7-aa-bbTG -dd-ee-ff

ET-5x7-aa-bb-ccAC -ee-ff

ET-5x7-aa-bb-ccDC -ee-ff

ET-5x7-aa-bb-cc-ddO30 -ff

ET-5x7-aa-bb-cc-dd-eeAL

ET-5x7-aa-bb-cc-dd-eeRM

Touch screen (membrane)

Touch screen glass

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Outdoor installation -30 °C [-22 °F] *

Aluminium front plate

Rear mount module

NOTICE * The O30 option is only available for AC devices !

Page 24 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Type code Operating Instructions ET-xx7

**10.5 ET-5x7-*-BT (Thin Client)**

NOTICE

These versions apply to all Thin Client's starting from hardware revision 01.03.01, with Bay Trail ATOM E3845 processor.

ET-5x7-aa-BT-bb-cc-dd-ee-ff-gg-hh-ii

Device variant:

Classification product key

ET-5x7SX -BT-bb-cc-dd-ee-ff-gg-hh-ii

Front design

Outdoor option

Voltage supply

Audio

Data memory

RAM

Touch screen

Display type

Processor type (fixed to BT = Bay Trail)

Ethernet interface

567 / 577 / 587 middle digit = display size

6 = 56 cm / 22" display

7 = 61 cm / 24" display

8 = 61 cm / 24"WU display

ET-5x7LX -BT-bb-cc-dd-ee-ff-gg-hh-ii

ET-5x7TX -BT-bb-cc-dd-ee-ff-gg-hh-ii

ET-5x72TX -BT-bb-cc-dd-ee-ff-gg-hh-ii

ET-5x7-aa-BTTFT -cc-dd-ee-ff-gg-hh-ii

ET-5x7-aa-BT-bbT -dd-ee-ff-gg-hh-ii

ET-5x7-aa-BT-bbTG -dd-ee-ff-gg-hh-ii

ET-5x7-aa-BT-bb-ccR3 -ee-ff-gg-hh-ii

ET-5x7-aa-BT-bb-cc-dd64GB -ff-gg-hh-ii

ET-5x7-aa-BT-bb-cc-dd128GB -ff-gg-hh-ii

ET-5x7-aa-BT-bb-cc-dd-eeSND -gg-hh-ii

ET-5x7-aa-BT-bb-cc-dd-ee-ffAC -hh-ii

ET-5x7-aa-BT-bb-cc-dd-ee-ffDC -hh-ii

ET-5x7-aa-BT-bb-cc-dd-ee-ff-ggO30 -ii

ET-5x7-aa-BT-bb-cc-dd-ee-ff-gg-hhAL

ET-5x7-aa-BT-bb-cc-dd-ee-ff-gg-hhRM

NOTICE

Description

Type with

Optical fiber Ethernet interface 1000Base-SX

(Ex op is), multi-mode

Additional with 1x copper Ethernet interface

10/100/1000Base-TX up from HW-Rev. 01.03.02

Optical fiber Ethernet interface 1000Base-LX

(Ex op is), single mode

Additional with 1x copper Ethernet interface

10/100/1000Base-TX up from HW-Rev. 01.03.02

Copper Ethernet interface 10/100Base-TX

(Ex e)

2x Copper Ethernet interface 10/100Base-TX

(Ex e)

TFT display (standard)

Touch screen (membrane)

Touch screen glass

4 GB RAM

64 GB Solid State Drive

128 GB Solid State Drive

Audio amplifier (mono amplifier) 3.5 W

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Outdoor installation -30 °C [-22 °F] *

Aluminium front plate

Rear mount module

* The O30 option is only available for AC devices !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 25 of 92

Operating Instructions ET-xx7 Type code

**10.6 ET-577-*-P2 (Thin Client)**

NOTICE

ET-577-aa-P2-bb-cc-dd-ee-ff-gg-hh-ii

Device variant:

Classification product key

ET-5772TX -P2-bb-cc-dd-ee-ff-gg-hh-ii

ET-577-

These versions apply to all Thin Client's starting from hardware revision 01.03.04, with AMD GX processor.

-P2-bb-cc-dd-ee-ff-gg-hh-ii

ET-577-aa-P2TFT

ET-577-aa-P2-bb-

-cc-dd-ee-ff-gg-hh-ii

-dd-ee-ff-gg-hh-ii

TG -dd-ee-ff-gg-hh-ii

ET-577-aa-P2-bb-ccR3 -ee-ff-gg-hh-ii

ET-577-aa-P2-bb-cc-dd64GB -ff-gg-hh-ii

ET-577-aa-P2-bb-cc-dd128GB -ff-gg-hh-ii

ET-577-aa-P2-bb-cc-dd-ee-ffAC -hh-ii

ET-577-aa-P2-bb-cc-dd-ee-ffDC -hh-ii

ET-577-aa-P2-bb-cc-dd-ee-ff-gg-hhAL

Front design

Outdoor option

Voltage supply

Audio

Processor type (P2 = AMD GX)

(unavailable)

Data memory

RAM

Touch screen

Display type middle digit

(unavailable)

Ethernet interface

display size

61 cm / 24" display

Description

Type with

2x Copper Ethernet interface 10/100Base-TX

(Ex e)

Optical fiber Ethernet interface 1000Base-SX

(Ex op is), multi-mode, additional 1x copper Ethernet interface

10/100/1000Base-TX

Optical fiber Ethernet interface 1000Base-LX

(Ex op is), single mode, additional 1x copper Ethernet interface

10/100/1000Base-TX

TFT display (standard)

Touch screen (membrane)

Touch screen glass

4 GB RAM

64 GB Solid State Drive

128 GB Solid State Drive

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Aluminium front plate

Page 26 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Type code Operating Instructions ET-xx7

10.7 ET-6x7 KVM System

ET-6x7-aa-bb-cc-dd-ee-ff-gg

Device variant:

Classification product key

ET-6x7DVI1-CAT -bb-cc-dd-ee-ff-gg

Front design

Outdoor option

Voltage supply

Audio

Touch screen

Display type

Transfer technology

667 / 677 / 687 middle digit = display size

6 = 56 cm / 22" display

7 = 61 cm / 24" display

8 = 61 cm / 24"WU display

ET-6x7DVI1-MM -bb-cc-dd-ee-ff-gg

ET-6x7DVI1-SM -bb-cc-dd-ee-ff-gg

ET-667DVI2-CAT -bb-cc-dd-ee-ff-gg

ET-6x7DVI3-CAT -bb-cc-dd-ee-ff-gg

ET-6x7DVI3-MM-FO -bb-cc-dd-ee-ff-gg

ET-6x7DVI3-SM-FO -bb-cc-dd-ee-ff-gg

ET-6x7-aaTFT -cc-dd-ee-ff-gg

ET-6x7-aa-bbT -dd-ee-ff-gg

ET-6x7-aa-bbTG -dd-ee-ff-gg

ET-6x7-aa-bb-ccSND -ee-ff-gg

ET-6x7-aa-bb-cc-ddAC -ff-gg

ET-6x7-aa-bb-cc-ddDC -ff-gg

ET-6x7-aa-bb-cc-dd-eeO30 -gg

ET-6x7-aa-bb-cc-dd-ee-ffAL

ET-6x7-aa-bb-cc-dd-ee-ffRM

NOTICE

Description

Type with

DVI1 KVM, with direct copper connection, Gigabit

(Ex e)

DVI1 KVM, with direct optical fibre connection

(Ex op is), multi-mode

DVI1 KVM, with direct optical fibre connection

(Ex op is), single mode

DVI2 ** KVM, with direct copper connection,

Gigabit (Ex e)

DVI3 KVM, with direct copper connection, Gigabit

(Ex e)

DVI3 KVM, with direct optical fibre connection

(Ex op is), multi-mode

DVI3 KVM, with direct optical fibre connection

(Ex op is), single mode

TFT display (standard)

Touch screen (membrane)

Touch screen glass

Audio amplifier (mono amplifier) 3.5 W

Power supply 100 - 240 VAC, 50 - 60 Hz

Voltage supply 24 VDC

Outdoor installation -30 °C [-22 °F] *

Aluminium front plate

Rear end module

* The O30 option is only available for AC devices !

* * The DVI2 KVM solution is only available together with the ET-667

HMI device !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 27 of 92

Operating Instructions ET-xx7 Safety information

11 Safety information

CAUTION

The notes listed in section 11. must be heeded to avoid injury and damage to equipment !

11.1 General Safety Information



All relevant accident prevention regulations and the rules for electric installations have to be observed during installation, maintenance and operations. All persons involved in installation, commission, maintenance and repairs of this device and its accessories must be qualified accordingly and must have familiarised themselves with this manual and any associated documentation.



In case of non-compliance or contravention of the above explosion-protection is no longer guaranteed and all warranty claims shall be null and void.



National safety and accident prevention rules apply.



Use the device for its intended purpose only.



No changes to the device are permitted. The enclosure may only be opened by R. STAHL

HMI Systems GmbH.

ATTENTION

For reasons of explosion protection, there is, due to the design, a small gap between the touch surface and the cover. Therefore, the devices should not be used in high pollution environments !

Under conditions of high pollution the manufacturers understand areas in which solid particles, smaller than 100 μm, form sludge and incrustations and thus can clog the gap.

11.2 Cautionary note

ATTENTION

This is an EN 55022 Class A product.

In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

11.3 Installation safety information



The in each case valid national assembly and installation rules and the generally accepted technical rules must be observed. The device and its accessories must be connected and operated according to applicable standards, directives and installation guidelines. Only qualiﬁed personnel or personnel that has been instructed accordingly are allowed to install the device.



The HMI device has been certified as a fixed installed device. It must be fixed with a bracket or be secured in another way at a specified position.



The HMI device must be disconnected from the mains for a change of position. The EPL must be adhered to.



The HMI device's front should be protected by a canopy against permanent exposure to

UV light. This increases the front membrane's lifespan. The canopy MUST NOT be too close to the front plate and sufficient air circulation must be ensured.



Only appropriate tools must be used for the installation.



According to IEC 60950, a suitable, easily accessible circuit breaker must be installed outside of the xx7 (version AC) which can cut the power line.



The screws on the lid of the Ex e connection box must be fastened with a torque of 1 Nm.

Page 28 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Safety information Operating Instructions ET-xx7



The cable connections of the connection box must be in line with country-specific regulations and may have to be adapted accordingly. Potential changes to the ambient parameters such as temperature must be taken into account.



The cable entries in the connection box must have ingress protection IP66 or may have to be adapted to meet country-specific requirements. The pre-assembled cable entry threads are:

- 2x M16x1,5

- 1x M20x1,5

- 3x M25x1,5

The wall of the terminal box where the cable entries are mounted has a thickness of at least 4 mm.



The cable connections must be tightened fast according to regulations. Unused cable connections must be sealed with appropriate blind plugs. Only permanently laid cables may be connected to the pre-mounted ATEX cable connections.



The outer cable diameters must correspond to the cable connection specifications.

- Cable entry M16 for round cable, outside cable cross-section

4...8 mm (0.16"...0.31") or 5...10 mm (0.197"...0.39")

- Cable entry M20 for round cable, outside cable cross-section

6...12 mm (0.24"...0.47")

- Cable entry M25 for round cable, outside cable cross-section

14…18 mm (0.55"…0.71")



The HMI device must not be opened, maintained or repaired in hazardous atmospheres

(sole exception: the Ex e connection box).



Before opening the Ex e connection box, ensure that all Ex e and Ex i circuits are fully de-energised and isolated. You must also ensure that the power supply circuit is isolated.

The cable diameter must meet the terminal specifications. The Ex e connection box must be tightly sealed.



All Ex e and Ex i circuits must be completely de-energised before the HMI device is connected. After the Ex e and Ex i circuits have been de-energised, wait for at least seven minutes before opening the Ex e connection box. The Ex e connection box must not be opened if the HMI device is energised.



The earth / ground (equipotential bonding) connector at the back of the HMI's enclosure must be connected to the equipotential bonding conductor of the hazardous area. The earthing cable must have a minimum cross section of 4 mm² and be fitted properly. To prevent equalizing currents flowing to the earth / ground (equipotential bonding) system of the HMI device it is necessary to safely isolate any connected devices from earth or to integrate them into the earth / ground (equipotential bonding) system of the HMI device.



We recommend you use screened cables with the HMI device. Routing of the data cable may reduce performance. Cables for intrinsically safe wiring have to pass a test voltage of

AC 500 V / DC 750 V. Use the values 200 pF/m and 1 μH/m at unknown cable properties.



We recommend you use a PG fitting (e.g. UNI_Dicht_HF TM ) for the screen connection over a large surface of the data cable between the 6x7-KVM-DVI3 transmission unit and the HMI device. In this case, the data cable's scree must not be connected again inside the HMI device at the screen connection rail.



If display types ET-xx7-DVI1-MM or ET-xx7-DVI1-SM are used, terminal X16 remains unused.



To establish a secure earthed connection between HMI device and plant and to prevent inadvertent loosening of the cables, each cable with its screen must be connected to the corresponding earthing bracket located in the Ex e connection box close to the associated terminal.



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 29 of 92

Operating Instructions ET-xx7 Safety information



At the place of installation voltage must not exceed 250 V and short-circuit current must not exceed 1500 A.



A tick close to the X10 terminal indicates the voltage type (AC / DC). For the 24 VDC types the cable cross-sections depend on the cable length of the voltage supply cable, as follows:

Cable length in metres (ft) Cable cross-section in mm² (AWG) max. 55 m (180 ft) max. 90 m (295 ft) max. 150 m (492 ft) max. 225 m (738 ft) max. 375 m (1230 ft) max. 600 m (1968 ft)

1.5 mm² (AWG16)

2.5 mm² (AWG14)

4 mm² (AWG12)

6 mm² (AWG10)

10 mm² (AWG8)

16 mm² (AWG6)

If the cable's cross section is greater than the maximum possible for the terminals, the cable needs to be routed according to regulations via a smaller cable cross section before being inserted into the connection box (possibly using the Ex e terminal box).



When the interface of intrinsically safe devices / partial intrinsically safe devices was or is connected to not intrinsically safe interfaces, the license will become void and it must be operated as a not intrinsically safe device. If the device was operated on an intrinsically safe interface with a lower level of international protection (e.g. an Ex ia device on an

Ex ib interface), it must not be operated afterwards in applications for a higher level of international protection (e.g. Ex ia).



If the HMI device is being used in a dust atmosphere and must be replaced, the device or the enclosure in which it is mounted must be disconnected from the mains first and then, according to regulations, be left to cool down. Before opening the HMI device or its enclosure and whilst they are open, the environment must be kept dust-free so that no dust can intrude into the inside of the enclosure. When mounting new components please ensure that all seals are undamaged and fit tightly.



Before starting up the HMI device you must ensure that it has been installed according to regulations and that neither the device nor its cables are damaged.

ATTENTION

The audio Interface (X105) can handle high voltage up to 100 V. For installation and wiring the national standards must be observed and a properly insulation needed to prevent a hazard.

11.3.1 Only for HMI devices with DVI3



The USB interfaces of the ET-6x7-DVI3 devices are only certified for the connection of keyboards and pointer units from R. STAHL HMI Systems GmbH.

11.3.2 HMI installation in enclosures with degree of protection "e" or "t"

If the ET-xx7 HMI devices are mounted inside an enclosure with degree of protection Ex e or

Ex t, the mechanical impact protection and the IP of the enclosure (up to IP65) is retained even after the device has been installed. The internal separation requirements and the temperature conditions of the Ex e enclosure must adhere to the applicable directives. The distance between the terminals of the HMI devices and other, insulated, conductive parts (except earth) within the

Ex e enclosure must be at least 50 mm.

Page 30 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Safety information Operating Instructions ET-xx7

11.3.3 Conditions of safe use according to CEC / NEC / CSA



Application supporting devices connected to the intrinsically safe input / outputs of connection points X101, X105, X97, X13, X14, and X16 shall be installed in a nonhazardous location (see control drawing 11100024) or must be suitable protected by an explosionproof or Ex p enclosure.



Connection point X10 shall be connected to a Class 2 supply for the DC model.



All connections to the display unit shall be installed using a CSA certified or us ULc listed

Ex e cable gland suitable for the end installation and shall carry a minimum IP rating of

IP65.



Any non-metallic parts of the HMI device that can accumulate static electricity must be cleaned only with a damp cloth.

11.3.4 Tightening torque

11.3.4.1 Terminals

NOTICE

11.3.4.2 Cable glands

The stipulated tightening torques of the connection terminals must be observed and applied. Again, they must be checked and possibly adjusted before commissioning !



The tightening torques for the cable glands may vary depending on the cables and wires used. The users have to determine and apply the required torques themselves.



In the case of ex-factory systems, all components are installed correctly and in accordance with applicable standards. Since storage or temperature etc. can have an impact on the cables and cable glands, the pre-installed screw connections must be checked and possibly tightened before commissioning.



If they are too loose or too tight, the type of protection, sealing or strain relief might be negatively impacted.



Cable glands with cap nut and without strain relief clamp should only be used for permanently installed cables and electrical lines. Installation of the required strain relief is the responsibility of the system set-up engineer.

11.4 Industrial Security

Our products with Industrial Security functions support the secure operation of plants, systems and equipment. Protection against cyber threats requires an all-encompassing Industrial

Security concept. The key to a successful concept is integrated implementation, continuous maintenance and state-of-the-art technology. This is the responsibility of the plant operator.

The following are key issues for an effective Industrial Security concept:



Prevention of unauthorised access to plants, systems, equipment and networks



Systems, equipment and components should only be connected to the company intranet or the internet if and when required



Employ protective measures such as firewalls and network segmentation



Only use the latest software product versions



Carry out software updates as soon as new versions are available



Use standard user accounts for regular operation



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 31 of 92

Operating Instructions ET-xx7 Safety information



Use secure passwords



Appropriate safeguarding of administrator accounts



Application of security guidelines



Other measures to be taken as required

R. STAHL is constantly working on enhancing its products, thereby contributing to plant security and to minimizing the risk of cyber threats.

11.5 Safety information for operation



Operate the HMI device only if it is clean and undamaged. If the HMI device is in any way damaged, do not touch it to avoid injury. In the case of any damage that may compromise ingress protection (e.g. cracks, holes or broken components) the HMI device must be taken out of commission immediately. Before the device is recommissioned the damaged components must be replaced.



If you want to use the device in zone 20, 21 or 22 as EPL Da/Db/Dc, dust deposits of a thickness exceeding 5 mm must be removed and you have to ensure that no high-energy loading mechanisms at the operating surface of the unit (e.g. pneumatic particle transport) occur during operation. The HMI device may not be used in environments where propagating brush discharges may occur.



In general, and particularly when opening and closing enclosures, users must take care not to get injured by getting caught / trapped.



In case of non-compliance or contravention of the above explosion-protection is no longer guaranteed and all warranty claims shall be null and void.

11.6 Special conditions



Along the intrinsically safe circuits between the display unit and pointing device potential equalization must exist.



The pointing device shall not be used in areas where charging mechanism creating propagating brush discharges have to be regarded.

Page 32 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Assembly and disassembly Operating Instructions ET-xx7

12 Assembly and disassembly

12.1 General information

NOTICE

Assembly and disassembly are subject to general technical rules.

Additional, specific safety regulations apply to electronic and pneumatic installations.

12.2 Cut-out ET-xx7

Make a cut-out with the following dimensions:

Width Height

615 ± 0.5 435 ± 0.5

24.21" ± 0.002" 17.13" ± 0.002"

Depth of cutout

110

4.33"

12.3 Tightening torque

Material thickness up to 5 up to 0.02"

Unit of mesurement mm inch (")

NOTICE

The tightening torque of the nuts for the fixing bolts of the

ET-4x7/5x7/6x7 panel mount devices is 1.2 Nm (+- 0.2 Nm) !



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 33 of 92

Operating Instructions ET-xx7 Operation

13 Operation

13.1 General information

NOTICE

13.2 Connections

When operating the devices, particular care shall be taken that:



the HMI device has been properly installed according to instructions,



the HMI device is undamaged,



the terminal compartment is clean,



all screws are tightened fast,



before switching the HMI device on, its external equipotential bonding terminal is properly connected to the equipotential bonding system at its place of use,



the cover of the terminal compartment is completely closed.

Terminal Pin

X10

PWR

Definition / typical cable color

Power supply HMI device +24 VDC or 100 - 240 VAC

2 Power supply HMI device 0 VDC or 100 - 240 VAC

3 Earth connection

X11

KBi

X12

X13

2 D-

3 D+

+UB

D-

D+

GND

+UB

GND

+UB

D-

D+

GND

Red

White

Green

Black

Red

White

Green

Black

Red

White

Green

Black

Connection

Power supply of the HMI device.

Ex e

USB interface

Ex ia for

External keyboard

USB interface

Ex ia for

Mouse

USB Ex e

X14 1 +12 V

2 GND

Red

Black

12 VDC output

Ex e, max. 500 mA

X16 TX 2TX TX 2TX Ethernet copper

CAT7 / 1 TRD0+ TxD + 1 White / Orange White / Orange 1 connection *

CAT5

Data

TRD0-

TRD1+

TxD - 1

RxD + 1

Orange

White / Green

Orange 1

White / Green 1

Ex e either *

TRD1-

TRD2+

TRD2-

RxD - 1

TxD + 2

TxD - 2

Green

Blue / White

Blue

Green 1

White / Orange 2

Orange 2

TX or 2TX

7 TRD3+ RxD + 2 White / Brown White / Green 2

8 TRD3- RxD - 2 Brown Green 2

9 SHLD SHLD Screen Screen

(2TX not for

600 SERIES)

X18

FO 1

Data

Optical fibre connection type LC

Duplex connector

Ethernet optical fibre interface *

Ex op is

Page 34 of 92

Tx Rx



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

X105

AUD

X105

AUD

Operation

X24

USB1i

X25

USB2i

X97

SER

X101

CAM

1 +UB

2 D-

3 D+

4 GND

1 +UB

2 D-

3 D+

4 GND

1 TxD

2 RxD

3 RTS

4 CTS

5 GND

1 Signal FBAS

2 Screen (GND)

1 CH1 / line out left

2 CH2 / line out right

3 CH3 / line in left

4 CH4 / line in right

5 GND

1 LS1+

2 LS1-

3 LS2+

4 LS2-

5 GND

Red

Black

Red

Black

Black or

Red

Black

Red

Black

Red

White

Green

Black

Red

White

Green

Black

Blue / White

Blue

White / Orange

Orange

Black

White

Black

Operating Instructions ET-xx7

USB interface

Ex ia

USB interface **

Ex ia

Serial

Ex e interface

RS-232

Video

Ex e interface

(optional) not for ET-x77-*-P2 devices

Audio

Ex e interface

(Line in only

600 SERIES)

Audio sound

Ex e interface

(optional) not for ET-x77-*-P2 devices



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 35 of 92

Operating Instructions ET-xx7

NOTICE

Operation

The following applies to all terminals:

0.2 - 2.5 mm² / AWG24 - AWG14 for flexible cable

0.2 - 4 mm² / AWG24 - AWG12 for rigid cable

Strip cable of 7 mm (0.28 in) insulation max. one cable per terminal

Recommended cable length for terminals X11, X12, X13, X14,

X24, X25: max. 3 m (10 ft)

* Please note that the Ethernet connection is either for an optical fibre connection (X18) or for a copper connection (X16), depending on the version ordered !

Up from HW-Rev. 01.03.02, all ET-4x7 and ET-5x7 devices with

SX and LX Ethernet interface are fitted additional with an

Ethernet TX interface !

The option 2TX is only possible at devices with Bay Trail (BT) and

AMD processor and NOT at 600 SERIES !

The device ET-x77-*-P2 has a second Ethernet TX (copper) interface in the TX version (1TX not available).

If display types ET-xx7-DVI1-MM or ET-xx7-DVI1-SM (optical fibre versions) are used, terminal X16 remains unused.

In the case of an optical fibre connection the following cable is recommended:

Multi-mode optical fibre cable:

50 µm core cross section and 125 µm external cross section

Single mode optical fibre cable:

9 µm core cross section and 125 µm external cross section

** The USBi2 connection (X25) is NOT available for devices with touch screen and may NOT be connected.

The unused wires of X16 at version 2TX must be isolated according to applicable regulations. This may be by means of double isolation and mechanical fixing by shrink sleeving or vulcanisation. The shrink sleeving or the vulcanisation must be suitable for at least 500 V and be within the temperature parameters of the device. The shrink sleeving / vulcanisation must NOT be light blue. When the data cables are shortened, this must also be kept in mind.

Page 36 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

General Information Operating Instructions ET-xx7

14 General Information

14.1 Touch driver

NOTICE

The UPDD touch driver is copyrighted licensed software supplied strictly for use with original R. STAHL HMI Systems GmbH touch systems and under no circumstances should this driver be downloaded or used on any other equipment !

14.2 ET-4x7 (Panel PC) and ET-5x7 (Thin Client)

14.2.1 Up to Windows 7 operating systems

14.2.1.1 Licensing issues

The HMI devices SERIES 400 and 500 which are pre-installed with a Windows operating system are equipped with a license sticker.

The license sticker is affixed on the back of the HMI device, next to the type plate.

Please note that according to the license issued for Windows the application of this system as an Office PC is not permitted.

DOCUMENTATION

Please also note the information on the licensing stipulations for Windows operating systems contained in the "TechNote Windows Operating Systems" file located on the CD / DVD / USB stick, which is part of the delivery.

14.2.1.2 Note on Windows Embedded operating systems

When using the Windows Embedded operating systems (XP or Windows Standard 2009 / 7) on the Panel PC devices SERIES 400, the C:\ system drive can be protected from unauthorised writing (EWF).

NOTICE This is NOT the case with other Windows operating systems !

ATTENTION

R. STAHL HMI Systems GmbH recommends you leave the write protection filter on at all times !

DOCUMENTATION

For further information regarding this Write Protection

(EWF), please refer to the OpenHMI_help_en.chm help file in the "STAHL" folder on the device or on the CD / DVD /

USB stick that is included in the delivery.

14.2.2 Windows® 10 IoT Enterprise 2019 LTSC operating system

The operating system is based on Windows 10 for PC platforms with 64 bit x86 processors. For the LTSC (Long Term Servicing Channel) versions, Microsoft guarantees 10 years of security updates and new builds with feature updates only every 2-3 years, with these being optional.

The LTSC versions are ideal for industrial applications and feature additional security components such as write filters (UWF) and HORM (start of a system snapshot from the RAM plus write protection).

From 2016 LTSB onwards, Microsoft has tied its licensing model to the processor performance:

ENTRY for AMD® GX and ATOM™

VALUE for Intel® Core i5™

HIGH for Intel® Core i7™



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 37 of 92

Operating Instructions ET-xx7 General Information

The Panel PC SERIES 400 HMI devices with Windows 10 IoT Enterprise 2019 LTSC operating systems have the license provided as part of the image, with the corresponding label affixed to the back of the device. When delivered, the devices have already been registered and activated.

The EOL (End of Life) date for Windows 10 IoT Enterprise 2019 LTSC for support and updates has been set by Microsoft to 09.01.2029.

14.2.2.1 Recovery

NOTICE

If a Panel PC is reset to the factory state (recovered) it will remain registered but will have to be reactivated !

This requires an active internet connection to a Microsoft server !

14.2.2.2 Company-specific Windows installations

NOTICE

The Windows 10 IoT license key is tied to STAHL images !

The installation of own Windows 10 IoT operating systems requires a separate license key !

All necessary drivers are provided by R.STAHL HMI Systems GmbH.

Please contact our Support department.

14.2.3 Initial start-up ET-4x7 (Panel PC)

When the device is started for the first time, the Windows installation assistant starts where users have to select certain settings.

Please follow the instructions of the installation assistant.

14.2.4 Recovery Stick

NOTICE

To restore your Panel PC device to its original state you will need a

Recovery Stick, which is part of the delivery. This recovery stick

(USB-drive) contains the factory image, with which the system can be restored to delivery status within a very short time.

Please note that you can restore the HMI devices to their original state only with the aid of the Recovery Stick

As an option, the recovery stick can also contain a backup software, with which you can back up your own device configuration.

The optionally available intrinsically safe recovery stick (USB i -drive) can not be used at the interfaces of the ET-xx7 devices !

14.2.5 Back-up

NOTICE

Please note that it is the sole responsibility of the operator to generate a back-up of the HMI devices and their overall function.

We strongly recommend such a back-up to be stored on an external storage medium or on the company network.

Page 38 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

General Information Operating Instructions ET-xx7

14.2.6 Switching off / closing down

NOTICE

The Microsoft Windows operating system stores key data in the main memory, regardless of the application, and has to store this data on the hard disk before the HMI device is switched off.

ATTENTION

It is therefore important for the safe and correct operation that the

HMI device is closed down properly (see illustration below) and NOT simply switched off.

Otherwise the existing image of the device may be damaged, rendering the HMI device non-functioning.

14.2.7 Data loss

NOTICE

In the case of applications that require constant writing into memory,

R. STAHL HMI systems recommends you use external storage media (USB sticks, network servers) for these write processes.

ATTENTION

Try and avoid cyclical writes (log files, databases, etc.) to the SSD !

The endurance of an SSD depends on the number of write cycles

(TBW / terabytes written).

Writing to the SSD with a simultaneous drop in voltage is most likely going to result in data loss !

14.3 Teaming function

NOTICE For SERIES 500 only

Processor

ATOM 3845

AMD

2TX

Yes

Teaming function

Interface

SX and TX

LX and TX



Providing redundancy due to automatic switch to a different network adapter.



Using the Ethernet adapters in the team as standby adapters, realising redundancy, making the system more fail-safe.



Bundling the speed of the Ethernet adapters in order to increase performance.

DOCUMENTATION

For a description of the function and its settings refer to the Remote HMI V6 software manual (industrial-grade

Thin Client firmware).



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 39 of 92

Operating Instructions ET-xx7 Maintenance, overhaul

15 Maintenance, overhaul

Because the transmission of the devices remains reliable and stable over long periods of time, regular adjustments are not required.

Keep the units clean so that the enclosure locks and screws remain accessible. Maintenance may be required for the enclosure seal.

System maintenance should focus on the following: a. Seal wear b. Display damage c. All screws are tightened fast d. All cables and lines are properly connected and undamaged

CAUTION

If the device in its factory state is damaged or altered in any way, decommission it immediately and contact the R. STAHL HMI

Systems GmbH !

If small glass beads (filling material) escape the device, immediately decommission the device !

15.1 Damaged sealing

NOTICE

If a defective seal is found on a device that has been returned to the manufacturer, an agreement is made with the customer as to whether it should be repaired (replaced).

If this exchange is not necessary, the option "No hazloc approved panel mount" is marked on the device by the manufacturer.

The device is only approved for installation inside an Ex e or Ex tb enclosure if no "No hazloc approved panel mount" option is indicated on the device !

16 Troubleshooting

Devices operated in hazardous areas must not be modified. Repairs may only be carried out by qualified, authorized staff specially trained for this purpose.

NOTICE

Repairs may only be carried out by specially trained staff who are familiar with all basic conditions of the applicable user regulations and – if requested – have been authorized by the manufacturer.

16.1 Repairs / hazardous substances

An error description must be enclosed with any units returned to R. STAHL HMI Systems GmbH for repairs.

Remove all material residues. Please pay particular attention to the seal grooves and slits where material residues may be lodged. We have to ask you not to return a unit if you are unable to completely remove any hazardous substances. We shall bill you for any costs arising from insufficiently cleaned units, such as disposal or damage to persons (chemical burns, etc.).

Page 40 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Disposal / Restricted substances Operating Instructions ET-xx7

17 Disposal / Restricted substances

Disposal of old electric and electronic devices, packaging and used parts is subject to regulations valid in whichever country the device has been installed.

For countries under the jurisdiction of the EU the corresponding WEEE directive applies.

The devices are classified according to the table below:

Directive

Valid

17.1 Declaration of substances and restricted substances

The present declaration is based on the procedure described in the international standard and directives as listed in the table below:



IEC 62474 : 2018 (DIN EN IEC 62474 : 2019-09)



(EG) Nr. 1907/2006 (REACH)



Directive 2011/65/EU (RoHS)



Resolution MEPC.269(68) "International Maritime Organization" (IMO); particularly

"2015 Guidelines for the Development of the Inventory of the Hazardous Materials" (IHM)

17.1.1 Declarable substance groups

ECHA Legal Entity UUID of the R. STAHL HMI Systems GmbH:

ECHA-a4dd94d5-bcd2-405d-8fdd-010a535d7e87

SCIP number: c335aec6-42c1-4204-8edf-b5b8d26ee81e

Component Designation

Mass

(g)

Declarable Substance

Groups and Substances

(IEC 62474 database)

CAS Nr. Mass %

Exemption

(acc. to directive)

BR2032

Lithium coin cell

2.6

Ethylenglycoldimethylether

(1.2-Dimethoxyethan /

EGDME)

BR2330

Lithium coin cell

3.2

Ethylene glycol dimethyl ether

(1.2-Dimethoxyethan /

EGDME)

17.1.2 RoHS directive 2011/65/EC

110-71-4

The devices meet the requirements of RoHS Directive 2011/65/EU.

3.6104

3.8100



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 41 of 92

Operating Instructions ET-xx7 Defective pixels

17.1.3 IMO Resolution MEPC.269(68)

The devices meet the requirements of the MEPC.269(68) Resolution of the "International

Maritime Organization" (IMO), in particular the "2015 Guidelines for the Development of the

Inventory of the Hazardous Materials" (IHM).

18 Defective pixels

As a result of the manufacturing process (production tolerances and errors) for the displays they may be delivered with defective pixels. Provided they are within the range of the specification below these potential defective pixels are not a display or HMI error or defect.

18.1 Terminology

Defective pixels Pixels or sub-pixels that do not perform as expected and are either always on or always off

Pixel Image point on the display consisting of 3 sub-pixels in the basic colours red, green and blue

R G B

Dot

Bright

Sub-pixel in the basic colour red, green or blue

R or G or B

Sub-pixel (dot) to which light is passing through, creating a bright dot that is on

Dark Sub-pixel (dot) to which no light is passing through, creating a dark dot that is off adjacent dots dots positioned next to one another, horizontally, vertically or diagonally, bright or dark

(e.g. the following pattern and sub-pixels)

R G B R G B R G B R G B

Page 42 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Defective pixels Operating Instructions ET-xx7

Distance between

Dots

Definition of distance between two defective dots horizontal, vertical or diagonal, bright or dark

(e.g. the following pattern and sub-pixels)

R G B R G B R G B R G B

18.2 Display specification ET-x77

Type of defect / description

Linear defect (horizontal, vertical, diagonal)

Defective pixels bright dots dark dots total number of dots adjacent dots

2 bright dots more than 3 bright dots

2 dark dots more than 3 dark dots

Distance between the dots between 2 bright dots between 2 dark dots

between 1 bright and 1 dark dot

ND filter for mura effects, bright and dark dots max. number of permitted defects

24" display not permitted

≤ 2

≤ 5

≤ 1 pair not permitted

≤ 2 pairs not permitted

≥ 15 mm

≥ 15 mm view with 8% filter



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 43 of 92

Operating Instructions ET-xx7

19 Control Drawing CEC / NEC / CSA

Control Drawing CEC / NEC / CSA

Page 44 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Control Drawing CEC / NEC / CSA Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 45 of 92

Operating Instructions ET-xx7 Mounting inside enclosure with ET-xx7 mounting-set

20 Mounting inside enclosure with ET-xx7 mounting-set

Page 46 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Mounting inside enclosure with ET-xx7 mounting-set Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 47 of 92

Operating Instructions ET-xx7

21 Declarations of conformity

21.1 EC

Declarations of conformity

Page 48 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 49 of 92

Operating Instructions ET-xx7

21.2 RCM

Declarations of conformity

Page 50 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 51 of 92

Operating Instructions ET-xx7

21.3 EAC

Declarations of conformity

Page 52 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 53 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 54 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 55 of 92

Operating Instructions ET-xx7

21.4 CCC

21.4.1 English version

Declarations of conformity

Page 56 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 57 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 58 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 59 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 60 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 61 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 62 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 63 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 64 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 65 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 66 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 67 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 68 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 69 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 70 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 71 of 92

Operating Instructions ET-xx7

21.4.2 Chinese version

Declarations of conformity

Page 72 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 73 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 74 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 75 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 76 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 77 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 78 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 79 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 80 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 81 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 82 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 83 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 84 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 85 of 92

Operating Instructions ET-xx7 Declarations of conformity

Page 86 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

Declarations of conformity Operating Instructions ET-xx7



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021 Page 87 of 92

Operating Instructions ET-xx7 Release notes

22 Release notes

The chapter entitled "Release Notes" contains all the changes made in every version of the operating instructions.

Version 01.03.21



Changing HW rev. at cover



Addition of table "Overview hardware revision"



Addition of "FSB notification"



Changing text (with and without lettering) according to documentation note in "Specific markings"



Addition of "cable glands" in "Technical Data"



Changing values according to "cable gland M16" in "Installation safety information"



Changing text in notice "No hazloc approved panel mount"



Addition of safety information "protection by a canopy" in "Installation safety information"



Adaption of data according to "optical fiber" in "Technical Data"



Moving information on "Interface copper" from chapter 4 "Technical Data" to subsection

4.1 "ET-4x7" and 4.2 "ET-5x7"



Adaptation of data for "Interface copper" in the subsections



Changing of P2 into AMD at "Video, Audio and O30 Option" in "Technical Data"



Addition of "USB standard 2.0" and "Note USB interfaces" in "Technical Data"



Addition of "Class I, Division 2 and according information" at "Marking" at NEC and CEC



Addition of CCC and CNEX certification



Formal changes

Version 01.03.22



Removal of previous release notes



Changing values "cable glands" in "Technical Data"



Changing values according to "cable gland M16" in "Installation safety information"

Page 88 of 92



R. STAHL HMI Systems GmbH / OI_ET_xx7_en_V_01_03_22.docx / 30.09.2021

R. STAHL HMI Systems GmbH

Adolf-Grimme-Allee 8

D 50829 Köln

T: (Sales Support)

(Technical Support)

E: (Sales Support)

(Technical Support) r-stahl.com exicom.de

+49 221 768 06 - 1000

+49 221 768 06 - 5000

+49 221 768 06 - 4100 [email protected]

[email protected]

Hi there! I've read the Stahl ET-xx7 Operating Instructions. This manual covers the installation, operation, and maintenance of the MANTA platform devices (SERIES 400 Panel PCs, SERIES 500 Thin Clients, and SERIES 600 KVM Systems). It includes safety information, technical specifications, and troubleshooting guides. I'm ready to assist you.

Show related prompts

Assistant typing

Assistant terminated

Key Features

Designed for use in hazardous areas
Available in a variety of configurations
Meet the highest safety standards
Backed by Stahl's commitment to quality and reliability
Rugged construction
Advanced features

Frequently Answers and Questions

What are the different types of Stahl ET-xx7 devices?

Stahl ET-xx7 devices are available in a variety of configurations, including panel PCs, thin clients, and KVM systems.

What safety standards do Stahl ET-xx7 devices meet?

Stahl ET-xx7 devices are designed to meet the highest safety standards, including ATEX, IECEx, and CSA.

What is the warranty on Stahl ET-xx7 devices?

Stahl ET-xx7 devices are backed by a 2-year warranty.