71-1957-250
10-97
ready-to-run O-27 set
Owner’s Manual
CAUTION—ELECTRIC TOY
NOT RECOMMENDED FOR CHILDREN UNDER EIGHT YEARS
OF AGE. AS WITH ALL ELECTRIC PRODUCTS, PRECAUTIONS
SHOULD BE OBSERVED DURING HANDLING AND USE TO
REDUCE THE RISK OF ELECTRIC SHOCK.
TRANSFORMER RATINGS —INPUT:120 VAC;60 HZ ONLY.
AC OUTPUT:20 V;54 VA
Congratulations!
ou’re now the proud owner of the Y
Mobil ready-to-run O-27 train set.
Everything you need to get started is included. You’re already off to a great start by reading this instruction manual.
It has important information on train setup and operation. This booklet also covers proper maintenance procedures to help your Lionel trains live long, healthy lives.
If you have any questions after reading this booklet, contact your nearest Lionel Authorized Service
Center using the list included in a separate flier in this set or call Lionel
Service at 810-949-4100. And have fun!
Table of contents
Track layout
Getting started
Suggested track layouts
Joining the track sections
Attaching the lockon to the track
Controller operations
Stripping the wire
Attaching the controller wires to the lockon
Controller functions
Controller and short circuits
Train operation
Reverse unit procedure
Tire traction
Coupling
Maintaining and servicing your set
Replacing your 4-4-2’s headlamp
Lubricating your 4-4-2 locomotive
Adding smoke fluid to your 4-4-2’s smoke generator
Limited Warranty/Lionel Service
10
11
11
12
8
9
9
6
7
5
5
4
4
3
3
Track layout
Getting started
efore you do anything else, we B recommend you check the contents of your set box to ensure all of the parts of your set have been included and that the quantities (when applicable) are correct.
The parts list below will tell you what’s included and the correct quantities. If you find any discrepancies, contact the dealer you purchased your set from for more information or call Lionel Service at 810-949-4100.
• 4-4-2 locomotive
• 8652 tender
• Mobil boxcar
• Mobil tank car
• Mobil caboose
• Controller
• 40-watt power pack
Now comes the fun part—deciding what kind of layout you want.
Suggested track layouts
1
1
1
1
1
1
1
• Lockon
• Straight track
• Curved track
• 90° crossover
• Billboard
• Smoke fluid
• Service Center list
The only rule—let your imagination be your guide.
2
1
1
12
1
1
8
Here are some examples of layouts you can build with track included with your train set.
Remember—the more track you own, the more variations you can create in your train layout. And that means more action and more fun!
Track layout
Joining the track sections
oin the track sections together J by inserting the pins of one track section into the rail openings of another. For good electrical contact, pins must be carefully inserted and track joints tightly fitted.
If the track is difficult to connect, try this installation tip. You can “break in” O-27 track sections by inserting and withdrawing a track pin into one rail at a time before joining the entire track section.
If the openings become too open
(causing the track to fit loosely), pinch
Attaching the lockon to the track
the rail together around a track pin with a pair of pliers. If any pins fall out of the track and are missing, replace them with extras available from your Lionel dealer.
Maintenance tip: The rails should be kept clean, dry, and free from oil and grease.
Clean rust and dirt spots with a track eraser. Wipe the track using a cloth dampened with track cleaner from the Lionel maintenance kit
(no. 6-62927), available from your nearest Lionel Authorized Value
Added Dealer or Lionel Service. he lockon connects power from T your controller to the track.
Attaching the lockon to the track is quick and easy.
LIO
CTC
LOCKO
NEL
First, place the lockon on onto the edge of an outside rail. Press the lockon upward so that the spring contact snaps onto the center rail. The lockon should face outward when under any straight section of track.
Fit the center lip of the lock-
1
2
N setting up your track and make sure it is firmly connected. Use the illustrations below as a step-by-step guide.
1
Hook lip to the outside of the rail
2
Snap spring contact to the middle rail
Once the lockon is securely attached to the track, it’s time to insert the wires from the controller into the two spring clips on the lockon. See page 5 for easy-to-follow steps.
Controller operations
Stripping the wire
nce your track is assembled and O the lockon is securely attached, you can connect the wires from the controller to the lockon.
First you‘ll want to check the ends of the wires to make sure that the insulation is stripped back about 1 ⁄
4
" to
3 ⁄
8
". To strip the wires, use a pair of wire strippers or a sharp knife.
C a u t i o n :
Only an adult should perform this task!
Always use care when stripping wires.
Attaching the controller wires to the lockon
N ow you’ll need to insert a controller wire into each of the two spring clips on the lockon.
It’s easy! Depress the spring clip with your finger and insert the bare end of the wire into the exposed opening.
Release the spring clip. Give the wire a little tug to make sure it’s secure. Repeat these steps with the other spring clip.
Next, insert the small plug end of the power pack into the back of your controller, and plug the other end into a standard outlet.
Note!
If the whistle fails to operate when you press the whistle button on your controller (see page 7), remove the wires from the lockon and reinsert each one into the opposite clip to reverse polarity.
Plug power pack into standard wall outlet
Make sure that the bare end of each wire is securely attached to the spring clip.
R
OF
F
FULL
SPEED
Plug this end into back of controller.
Controller functions
Controller functions
s you turn the throttle control knob A to the right, power to the track is increased. When the indicator reaches the green band, there should be sufficient power to operate the locomotive.
The further into the green area the knob is turned, the faster your train will go.
Remember that the greater the load on the engine (adding more cars for the engine to pull, for example), the farther into the green the knob must be turned before it will operate the locomotive.
The yellow band indicates the average power range that the train will be operating in. The red band represents maximum power output.
Press this button to produce a realistic whistle sound.
Press this button to go forward or reverse, or to place the locomotive in
“neutral” (no movement, headlight is on).
Turn the throttle control knob to the right for more power.
R
The LED indicator shows when your controller is O N .
Green band
Yellow band
Red band
OFF FULL
SPEED
Controller operations
Controller and short circuits
our Lionel power pack is listed by Y
Underwriters Laboratories Inc. and has been carefully designed and tested to ensure peak performance. The controller is equipped with a built-in electronic circuit breaker that alternately cuts off and restores the flow of power to the track whenever a short circuit exists—for example, when the train derails. The circuit breaker’s action continues until the cause of the short circuit is eliminated. This circuit breaker is incorporated into the controller to protect it from possible damage. It will not protect the locomotive or electrically operated accessories, so it’s important to eliminate short circuits as soon as possible.
Note!
The power pack must be unplugged from the wall socket when a short circuit is noticed, and the short circuit must be corrected.
A short circuit is caused by a direct connection between the center rail and one of the outside rails or by a direct connection between bare wires. The axles of a derailed car or locomotive are the most frequent cause of short circuits, so make sure that all wheels are properly set on the rails. Some other causes of short circuits might be staples, nails, paper clips, or other metallic objects lying across the rails, or two bare wires touching each other.
If too many cars or accessories are used, your controller will exceed its power limit and begin to cycle on and off. To correct this problem, cars or accessories must be removed before normal operation can resume. For more power, see the line of Lionel high-output transformers at your Authorized
Lionel Value Added Dealer.
The same condition can occur if the power is turned up too quickly. This also could cause your train to move too fast and derail.
After your power pack has been operating for a while, you will find it warm to the touch. It is the nature of all electrical power equipment to become warm when in use. If your controller is loaded to capacity, it is a good idea to let it cool down after an hour or two of continuous use. Unplug the power pack from the wall when the controller is not in use.
Train operation
Reverse unit procedure
T he reverse unit inside your Lionel locomotive is an electronic device that acts like the transmission in your car. When you apply power to the track, the locomotive moves in the direction specified by the reverse unit—or it sits in neutral, awaiting another power interruption.
Power interruptions locked in the next mode of operation in the sequence. For instance, if the locomotive is moving forward, then is stopped and the switch is thrown back, the locomotive will be “locked” in neutral. If the switch is thrown back while the locomotive is under power, the locoare the signal that tells the reverse unit to sequence to the next operational state. motive will remain in the mode it was in when the switch was thrown. The controller direction control will then have no affect on
To interrupt power and sequence the loco-
Reverse unit on/off switch motive’s reverse unit, press the direction control button or the direction of the locomotive.
Additionally, this reverse unit has a “power-up reset” featurn the throttle to the O FF position and
O N again. The reverse unit alternates between three states: forward, neutral, and reverse.
Also, the locomotive can be “locked” into a certain mode of operation by throwing the switch located on the underside of the frame (see illustration above). When the switch is thrown to the O FF position, the locomotive will be ture, which means that should the locomotive sit without power for a short period of time, the reverse unit will automatically reset and start in the forward direction when the transformer is turned on or “powered up,” regardless of the locking switch position. If the locking switch is in the O
FF position, the locomotive will start in the forward direction and be “locked” there.
R
Whistle control button
Direction control button
OFF
FULL
SPEED
Train operation
Tire-Traction ™
Y our locomotive is equipped with
Tire-Traction. This means that one of the drive wheels is fitted with a rubber traction tire to enhance tractive effort so your locomotive can
Coupling
fter you have assembled the track, A place the locomotive and rolling stock on the track. Before coupling the cars, make sure the wheels are properly set on the rails.
When coupling your cars, at least pull many cars at once.
Lionel locomotives with Tire-
Traction grip the track, enabling them to pull heavy loads at higher speeds. one of the mating couplers must be open as shown below at the left. Now simply push the cars toward each other until they lock together.
Now you’re ready to pull out of the station. All aboard!
Push down the lock release to open the coupler.
Keep in mind that it’s easier to couple cars on a straight stretch of track.
Note: Your observation car has only a front coupler, so it should be placed at the end of the train.
Maintaining and servicing your set
Replacing your 4-4-2 locomotive’s headlamp
our 4-4-2 locomotive lights the way Y with headlamp illumination.
During the course of normal operation, the lamp may require replacement.
First remove the two front truck screws and carefully slide the front truck assembly off the linkage rods.
Lift the smoke unit out far enough from the cab to allow lamp extraction.
Pull the lamp straight out and replace it with Lionel part no. 600-0161-300, available from your nearest Lionel
Authorized Service Center or from
Lionel Service. Be careful not to twist the lamp or it may break.
Now, reinstall the smoke unit, making sure that the smoke stack lines up with the cab top opening. Reassemble the front truck, making sure that the linkage rods go into the holes in the front truck. The lug wire from the smoke unit must be reinserted through the slot in the front truck assembly and secured under one of the two front screws. Tighten the screws firmly but do not over tighten.
Smoke unit
Linkage rods
Front truck screws
Smoke unit lug wire
Lionel part no.
600-0161-300
Maintaining and servicing your set
Lubricating your 4-4-2 locomotive
H elp your 4-4-2 steam locomotive lead a long and productive life on your railroad by maintaining it properly.
We recommend you purchase a
Lionel Lubrication and Maintenance Kit
(no. 6-62927), available from your Lionel dealer. Two basic rules to keep in mind:
Never over-lubricate (a small amount will do), and avoid getting grease or oil on the 4-4-2’s wheels, contact rollers, or your track.
You’ll know your 4-4-2 requires lubrication when visual inspection reveals dryness on the parts indicated in the illustration. Remove accumulated dirt and dust before lubricating, and always lubricate any locomotive emerging from prolonged storage.
Lubricate drive axles on both sides of locomotive (between the wheels and the locomotive at the bushings)
Lionel oil sparingly
Lubricate axle ends with Lionel oil sparingly
Lubricate gears with
Lionel grease sparingly
Lubricate with
Lionel oil sparingly
Adding smoke fluid to your 4-4-2’s smoke generator
Y our 4-4-2 locomotive is equipped with a smoke generator that produces safe, clean white smoke during operation.
The smoke generator requires the periodic addition of Lionel smoke fluid in order to function. Pierce the smoke fluid tube end with a pin, then add 4 to 8 drops of fluid directly into the locomotive’s stack. Smoke production commences momentarily, faster if you run your locomotive at high speed. When smoke production wanes, add more fluid (4 to 8 drops).
An idle locomotive will not smoke.
NOTE: Always keep a small amount of smoke fluid in the locomotive’s smoke generator; the generator ’s element can become damaged if operated without smoke fluid. This is particularly true if your locomotive sits in neutral for an extended period of time without smoke fluid in the generator.
Smoke production is greater at higher voltages and when the locomotive is pulling a heavy load or a long consist.
Limited Warranty/Lionel Service
his Lionel product including all mechaniT cal and electrical components, moving parts, motors and structural components, except for light bulbs, is warranted to the original consumer-purchaser, for 1 year against original defects in materials or workmanship when purchased through an authorized Lionel merchant.
This warranty does NOT cover normal wear and tear, light bulbs, defects appearing in the course of commercial use, or damage resulting from abuse or misuse of the product by the purchaser. Transfer of this product by the original consumer-purchaser to another person voids this warranty. Modification of this product voids this warranty.
Any warranted product which is defective in original materials or workmanship and is delivered by the original consumer-purchaser to
Lionel L.L.C. or an authorized Lionel L.L.C.
service center, together with proof of original purchase, will at the option of Lionel L.L.C. be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted. Any products on which warranty service is sought must be sent freight or postage prepaid, as transportation and shipping charges are not covered by the warranty.
IN NO EVENT SHALL LIONEL L.L.C. BE
LIABLE FOR INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you.
This limited warranty gives you specific legal rights, and you may have other rights which vary from state to state.
INSTRUCTIONS FOR OBTAINING SERVICE
If service for this Lionel L.L.C. product is required, bring the item, along with your dated sales receipt and completed warranty information to the nearest Authorized Lionel Service
Center. Your nearest Lionel Service Center can be found by calling 1-800-4-Lionel, or by contacting our Website @ www.Lionel.com
If you prefer to send it back to Lionel L.L.C.
for factory repair, you must first call 810-949-
4100 or FAX 810-949-5429 or write to Customer
Service, P.O. Box 748 New Baltimore, MI 48047-
0748 stating what the item is, when it was purchased and what seems to be the problem. You will be sent a return authorization letter and label to assure your merchandise will be properly handled upon receipt.
Once you have received your return authorization and label, make sure that the item is packed to prevent damage during shipping and handling. We suggest that you use the products original packaging. This shipment must be prepaid and we recommend that it be insured.
Please make sure you have followed all of the above instructions carefully before returning any merchandise for service.
WARRANTY INFORMATION
Please complete the information below and keep it, along with your dated sales receipt.
You must present this and your dated sales receipt when requesting warranty service.
NAME___________________________________
ADDRESS________________________________
PLACE OF PURCHASE____________________
DATE OF PURCHASE _____________________
PRODUCT NUMBER _____________________
PRODUCT DESCRIPTION
_________________________________________
© 1997 L
IONEL
LLC, C
HESTERFIELD
MI 48051-2493
U
NITED
S
TATES OF
A
MERICA
