QSC K Series K8, K10, K12 Loudspeaker System, K Series KSub Subwoofer System User Manual
Below you will find brief information for K Series K8, K Series K10, K Series K12, K Series KSub. These powered loudspeakers offer high power output, versatile connectivity, and advanced DSP features for clear audio reproduction. Ideal for portable and installed sound reinforcement applications, they are equipped for various mounting options and feature protective limiting circuitry.
Advertisement
Advertisement
K Series
User Manual
K8
– 105° 1000 W active 8" (200 mm) 2-way loudspeaker system
K10
– 90° 1000 W active 10" (250 mm) 2-way loudspeaker system
K12
– 75° 1000 W active 12" (300 mm) 2-way loudspeaker system
KSub
– Dual 12" (300 mm) 1000 W active 4th-order bandpass subwoofer system
TD-000280-00-D
*TD-000280-00*
IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS
WARNING!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE AMPLIFIER
COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous” voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of shock to humans.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in this manual.
ENG
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Allow a minimum of 6" (152 mm) clearance behind cabinet for convection cooling. Keep anything that might restrict airflow from the rear of the enclosure (i.e. draperies, fabric, etc.). Do not block any ventilation opening. This product contains an internal power amplifier that produces heat.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the grounding-type plug on the three-pronged “Edison” style power cable. The grounding plug has two blades and a grounding prong. The third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for the replacement of the obsolete outlet. Do not cut off the grounding plug or use an adapter that breaks the grounding circuit. This apparatus must be properly grounded for your safety.
10. Protect the power cord from being walked on or pinched, particularly plugs, convenience receptacles, and the point where they exit from the apparatus.
11. The appliance coupler is the AC mains disconnect and should remain readily operable after installation.
12. Use only attachments/accessories specified by QSC Audio Products, LLC.
13. Use only with hardware, brackets, and components sold with the apparatus or by QSC Audio Products, LLC.
14. Unplug the apparatus during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped.
16. Before placing, installing, rigging or suspending any loudspeaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation and should be immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term unexpected overloading. Never exceed the rating of the hardware or equipment.
17. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.
18. The appliance shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
2
Warranty (USA only; other countries, see your dealer or distributor)
QSC Audio Products 3 Year Limited Warranty
QSC Audio Products, LLC (“QSC”) guarantees its products to be free from defective material and/or workmanship for a period of three (3) years from the date of sale and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use – provided the unit is returned to our factory or one of our authorized service stations via prepaid transportation with a copy of proof of purchase (i.e., sales receipt). This warranty provides that the examination of the returned product must indicate, in our judgement, a manufacturing defect. This warranty does not extend to any product which has been subjected to misuse, neglect, accident, improper installation, or where the date code has been removed or defaced. QSC shall not be liable for incidental and/or consequential damages. This warranty gives you specific legal rights.
This limited warranty is freely transferable during the term of the warranty period.
Customer may have additional rights, which vary from state to state.
In the event that this product was manufactured for export and sale outside of the United States or its territories, then this limited warranty shall not apply. Removal of the serial number on this product, or purchase of this product from an unauthorized dealer will void this limited warranty.
Periodically, this warranty is updated. To obtain the most recent version of QSC’s warranty statement, please visit www.qscaudio.com.
Contact us at 800-854-4079 or visit our website at www.qscaudio.com.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s2EORIENTORRELOCATETHERECEIVINGANTENNA s)NCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDRECEIVER s#ONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROMTHATTOWHICHTHERECEIVERISCONNECTED s#ONSULTTHEDEALERORANEXPERIENCEDRADIO46TECHNICIANFORHELP
Package Contents
K8, K10, K12
(1) Loudspeaker system
(1) Locking power cable
(1) Euro-style Connector Plug, 3-pin
(1) K Series Hookup Drawings
(1) Warning Information Sheet
KSub
(1) Subwoofer system
(1) Locking power cable
(1) Euro-style Connector Plug, 3-pin
(1) M20 threaded loudspeaker pole
(1) K Series Hookup Drawings
(1) Warning Information Sheet
ENG
3
Features
K8
ENG
3. Front power LED
4. Cast aluminum handles
6. M10 installation points
7. M5 yoke attachment points
8. Tilt-Direct™ dual angle pole socket
7
4
1 6
9
7 2
7
5
8
9
7
3 6
K10
3. Front power LED
4. Cast aluminum handles
6. M10 installation points
7. M5 yoke attachment points
8. Tilt-Direct™ dual angle pole socket
7
9
4
1
4
7
4
6
2
7
5
9
3
6
8
7
4
K12
3. Front power LED
4. Cast aluminum handles
6. M10 installation points
7. M5 yoke attachment points
8. Tilt-Direct™ dual angle pole socket
KSub
1. Birch plywood enclosure
2. Front power LED
4. Cast aluminum handles
6. M20 threaded pole receptacle
7. 3" heavy duty casters
9 7
9
7
1
4
4
6
2
7
5
9
3
6
8
7
7
6
1
4
4
2
3
5
4
7
ENG
8
7
5
ENG
Applications
The K Series has been primarily designed for portable audio reinforcement. This includes a variety of uses in reinforcement for entertainers and presenters. The K8, K10 and K12 are all designed to perform well on their own in full-range audio. They can be used singly, in stereo pairs or in distributed or delayed systems. They perform extraordinarily well as both main reinforcement systems and as floor monitors (K10 and K12 only). (Figure 1)
The K8, K10, and K12 are all equipped with a 35 mm pole socket that allows use on a speaker stand or on a pole over a subwoofer. The pole socket features the QSC Tilt-Direct™ system for tilting the enclosures down 7.5 degrees while on the pole. (Figure 2)
The K8, K10 and K12 also have features designed for various suspension methods. They feature M10 threaded inserts for suspension with eyebolts. There are also yoke accessories (model numbers: K8 YOKE,
K10 YOKE, K12 YOKE) for each model that can mount either to the sides of the cabinet or to the top and bottom. These yokes allow for rigid mounting to structures and rotation of the speaker system. (Figure 3)
For extra low-frequency extension and enhancement, the KSub is perfectly matched to the rest of the K Series. The K8, K10 and K12 all have a selectable high-pass filter for use with the subwoofer. The KSub includes a fixed low-pass filter so it will accept full-range input.
The KSub has four large casters for maximum portability. The pole socket on the top of the enclosure is fitted with an M20 threaded insert. The included speaker pole screws into the socket for a secure fit. (Figure 4)
– Figure 1 –
– Figure 2 –
– Figure 3 –
6
– Figure 4 –
Installation
Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation or placement. Any such condition severely reduces the safety of the installation and should be immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term, unexpected overloading.
Never exceed the rating of the hardware or equipment.
Consult a licensed, professional engineer regarding physical equipment installation. Ensure that all local, state and national regulations regarding the safety and operation of loudspeakers and related equipment are understood and adhered to.
Recommended Deployment
K8:
The K8 was designed to sit on the floor, stage, subwoofer enclosure, be suspended, or be pole mounted on a 35 mm diameter loudspeaker support pole. When pole-mounted to the KSub, pole length must not exceed 31 inch (787 mm).
K10:
The K10 was designed to sit on the floor, stage, subwoofer enclosure, be suspended, or be pole mounted on a 35 mm diameter loudspeaker support pole. When pole-mounted to the KSub, pole length must not exceed 28.5 inch (724 mm).
K12:
The K12 was designed to sit on the floor, stage, subwoofer enclosure, be suspended, or be pole mounted on a 35 mm diameter loudspeaker support pole. When pole-mounted to the KSub, pole length must not exceed 26.5 inch (673 mm).
KSub:
The KSub was designed to sit on the floor or on the stage. A threaded pole cup on the top of the enclosure accepts a M20 threaded 35 mm loudspeaker mounting pole. There are additional M20 speaker poles available from third party suppliers. Rubber feet on the enclosure’s bottom help to minimize enclosure movement during operation. Do not pole mount or stack more than one enclosure on top of the KSub enclosure. As the casters will wear during normal use, it may be required to insert small foam pieces between the wheels and frames to minimize rattling at high output levels.
K8 WARNING! Do not use a loudspeaker support pole longer than 31 inch (787 mm) when supported by the KSub subwoofer.
ENG
K10 WARNING! Do not use a loudspeaker support pole longer than 28.5 inch (724 mm) when supported by the KSub subwoofer.
K12 WARNING! Do not use a loudspeaker support pole longer than 26.5 inch (673 mm) when supported by the KSub subwoofer.
K8
24.5"
(622 mm)
K SERIES
POLE
KSub
K10
24.5"
(622 mm)
K SERIES
POLE
KSub
7
K12
24"
(612 mm)
K SERIES
POLE
KSub
ENG
Integrated Suspension Points (suspended installations)
The K8, K10 and K12 enclosures each feature three load-rated M10 installation points.
As shipped from the factory, each pick point has a rubber plug installed to retain the sleek look of the enclosure. These installation points are designed for use with the eyebolts included in the available accessory kit, model number K SERIES M10 KIT. The installation points may also be used with any forged shoulder eyebolt with an M10 thread, provided the length of the thread is no more than 0.8 inch (20 mm).
Ensure all pick-point fasteners are installed and correctly tightened in order to maintain enclosure’s rated strength. Use either
QSC’s M10 forged shoulder eye bolts contained in K SERIES M10 KIT or an M10 forged shoulder eyebolt with a thread length no more than 0.8 inch (20 mm). Contact QSC Technical Services department for complete information.
K8 K10 K12
Cooling in Installed Applications
This is a self-powered loudspeaker containing an internal power amplifier that produces heat. Allow a minimum of 6" (152 mm) clearance at cabinet back for convection cooling. Keep anything that might restrict airflow away from the rear of the enclosure (i.e draperies, fabric, etc...).
Do not install enclosures with their rear panels exposed to direct sunlight. Direct sunlight will heat the amplifier module and reduce its ability to produce full output. Install sunshades if the application merits. Maximum ambient temperature for full performance to specification is 50° C (122° F). Do not install enclosures where exposed to rain or other water sources. The enclosure is not weatherproof. Outdoor installations must provide protection from the elements.
8
AC Mains
Connect AC power to the IEC socket on the back of the amplifier by locating the IEC connector-end of the
AC power cord and inserting it fully into the IEC inlet on the power amplifier module. NOTE: Turn off the AC power switch before connecting AC power.
4HE6,/#+POWERCORDHASASPECIALLATCHINGFEATURETOPREVENTTHEPOWERCORDFROMBEINGUNINTENTIONALLY removed. The IEC plug and socket are both blue in color so the power cord can be identified as a K Series loudspeaker cord. If the QSC supplied cord becomes lost or damaged, a standard replacement 18 gauge IEC
POWERCORDMAYBEUSED(OWEVERTHELATCHINGSYSTEMWILLONLYFUNCTIONWITHA6,/#+POWERCORDAVAILABLE from QSC Audio Products, LLC.
The K Series is fed by a universal power supply. This power supply is capable of operating the system with input AC power voltages ranging
FROM6!#ATn(Z
Use only the power cable that is correct for your location.
You may discard any other power cables, find an appropriate recycling opportunity or keep them if travel to other regions with the K Series product is likely.
AC Mains Disconnection
Turn the AC power switch to the off position. To remove the AC mains cord, grasp the IEC connector’s plastic body, press the yellow latch release button and pull, removing the connector from the socket.
Power Switch
Push in on the top of the rocker switch to apply AC mains power to the powered loudspeaker. Push in on the bottom of the rocker switch to turn the powered loudspeaker off.
When turned on, the green STANDBY indicator LED and the red LIMIT (limiter) indicator LED on the rear panel will illuminate; after a few seconds the red LIMIT indicator and the green STANDBY will extinguish, and the blue POWER indicator LED will illuminate.
Rear LED POWER Indicator
The blue LED POWER indicator on the rear panel will illuminate when the AC Power switch is in the “ON” position, the unit is not in standby, the
AC mains power cord is connected properly, and the AC mains are functioning properly. The rear LED POWER indicator will extinguish when the AC
Power switch is in the “off” position, AC mains power has been removed from the loudspeaker, or the amplifier enters standby.
If the rear LED POWER indicator does not illuminate when the Power switch is placed in the “on” position during the first 5 minutes of power being
APPLIEDVERIFYTHE!#MAINSLINECORDISPROPERLYATTACHEDTOTHELOUDSPEAKERANDPLUGGEDINTOTHE!#OUTLET6ERIFYTHEOUTLETISFUNCTIONINGPROPERLY
If the AC mains cordset is serviceable and the AC mains outlet is operating properly, but the loudspeaker fails to operate, the loudspeaker may require servicing. Contact QSC’s Technical Services department.
System Power Sequencing
Proper power turn on/turn off sequencing can help to prevent unexpected sounds from being produced by the system (pops, clicks, thumps). These unintended sounds can be unpleasant and take away from the overall professionalism of the presentation. Always follow the rule that speakers are “last on, first off”.
Power On Sequence: Bring the output level control of the mixer (or other audio source) feeding your speakers to its minimum position. Turn on all source devices (CD players, mixers, instruments), turn on subwoofer, then turn on the “top-boxes” (K8, K10, K12). The level controls on your mixer may now be brought up.
Power Off Sequence: Turn off “top boxes,” turn off subwoofer, then turn off all source devices.
If a K Series speaker is being driven from the output of another K Series unit, it should be turned on after the unit feeding it signal, and turned off before the unit feeding signal.
ENG
9
ENG
Input Connections
K8, K10, K12
Channel A MIC/Line Input
Combination XLR-M and
1/4" Phone Jack
Channel A MIC Level
Yellow LED Indicator
Channel A MIC/Line
Level Switch
Channel A Green
Signal Present LED
Channel A Gain
The K8, K10 and K12 are designed to accept MIC Level and Line Level inputs with several different connectors.
There are three input connection points on the input panel. Channel A will accept MIC or Line Level inputs by connecting a male XLR cable or a male 1/4" phone cable (either TS or TRS type may be used). For MIC Level, the
MIC/LINE selector switch must be in the “MIC” position. (Figure 5) When the selector switch is in the MIC position, activating the MIC Pre-amp, the yellow MIC level LED indicator will turn on. The MIC setting should only be used if a microphone is connected directly to the MIC/LINE input. Note that the input does not provide phantom power. The LINE setting should be used for most other audio inputs. (Figure 6)
The MIC setting should only be used if a microphone is connected directly to the MIC/LINE input. Using the MIC setting for other purposes may introduce distortion. Care should be taken when switching to the MIC position as the output level will increase significantly when the switch is flipped.
Gain for signal delivered on the Channel A XLR/1/4" combination jack is set using the Channel A Gain knob. This control sets the sensitivity of Channel A, and thereby the amount of signal sent to the power amplifier and, in turn to the loudspeaker components. It also sets the amount of signal sent to the Post-Gain Line Output. The green
SIGNAL LED will illuminate when signal is present, regardless of the amount of gain as set by the Gain knob. If the
LED does not illuminate, the input is not receiving any signal or the level of the signal is significantly low. Check all connections and the status of the device delivering the signal.
Channel B will accept Line Level input only, by connecting a male XLR cable or a male 1/4" phone cable (either TS or
TRS type may be used). Channel B will also accept mono or stereo Line Level input on a pair of RCA (phono) jacks.*
Gain for signal delivered on the Channel B line level XLR/1/4" combination jack and RCA (phono) jacks is set using the Channel B Gain knob. The Channel B Gain knob will control the input gain of Channel B, as well as the amount of signal sent to the Post-Gain Line Output. The green SIGNAL LED will illuminate when signal is present, regardless of the amount of gain as set by the Gain knob. If the LED does not illuminate, the input is not receiving any signal, or the level of the signal is significantly low. Check all connections and the status of the device delivering the signal.
Note: Unless the gain controls associated with all active inputs are set to 0 dB, the output signal from the
Post-Gain Line Output will not be at the same level as the input signal. If a “slave” speaker is intended to playback at the same level as the “master” speaker, the gain control on the “slave” speaker should be set to 0 dB.
10
Channel B Line Input
Combination XLR-M and 1/4" Phone Jack
Channel B Line Input
Phono (RCA) Jacks
Channel B Green
Signal Present LED
Channel B Gain
– Figure 5 –
– Figure 6 –
*Stereo input received at the RCA input jacks will be summed to mono.
Balanced Inputs:
Connect to the plug as shown.
1 = Shield (ground)
3 = Minus (-)
2 = Plus (+)
Ground
Inverting Input
Non-inverting Input
Unbalanced Inputs:
Connect to the plug as shown. If a 3 conductor (TRS) plug is used to connect an unbalanced source, Pin 3 and pin 1 must be connected with a jumper as shown.
1 = Shield (ground)
3 = Minus (-)
2 = Plus (+)
Ground
Non-inverting Input
Input Connections
KSub
ENG
Channel A Line Input
Combination XLR-M and 1/4" Phone Jack
Channel B Line Input
Combination XLR-M and 1/4" Phone Jack
Green Signal
Present LED
Channel A and B
Mixed Gain Knob
The KSub is designed to accept Line Level inputs connected either by male XLR or 1/4" phone (TS or TRS) jack. If signal is connected to both Channel
A and Channel B, they will be summed together. The gain of the summed signal is then controlled using the Gain knob. This affects the amount of signal sent to the amplifier and then to the loudspeaker components. The green SIGNAL LED will illuminate when signal is present, regardless of the amount of gain as set by the Gain knob. If the LED does not illuminate, the input is not receiving any signal, or the level of the signal is significantly low. Check all connections and the status of the device delivering the signal.
11
Output Connections
K8, K10, K12
Channel A Line
Level Direct Output
Channel A
Gain Knob
Channel B Line
Level Direct Output
Channel B
Gain Knob
ENG
Post-Gain
Line Output
Both Channel A and Channel B have discreet direct outputs on male XLR connectors. The signal on this output is exactly equivalent to the signal from the corresponding input. The level of the output signal is not affected by the gain setting for that channel. Additionally, signal delivered on the RCA
(phono) jacks is not present on the Channel B direct line level output.
The Post-Gain Line out male XLR connector is a mixed output of Channel A, Channel B and the RCA (phono) jacks. This mix is affected by gain knobs on both Channel A and Channel B and the MIC/LINE switch on Channel A, but the output level is still Line Level.
WARNING! Do not connect the POST-GAIN LINE OUTPUT of a K Series system to any INPUT of the SAME UNIT. This output is designed to send signal to OTHER K Series units or to other audio equipment. Failure to follow this warning may result in very unpleasant sounds produced at extremely high output volumes.
Output Connections
KSub
Channel B Line
Level Direct Output
Channel A Line
Level Direct Output
Channel A and B
Mixed Gain Knob
Both Channel A and Channel B have discrete direct outputs on male XLR connectors. The signal on this output is exactly equivalent to the signal from the corresponding input. The level of the output signal is not affected by the gain set on the subwoofer gain knob.
12
DSP Features
The K Series features advanced DSP (digital signal processing) circuitry that performs many functions. Some functions are set at the design/production level and are not user accessible. These functions include crossovers, time alignment, limiting and protection, thermal management and a number of proprietary features. QSC has designed exclusive DSP functions that greatly enhance the capabilities and performance of the K Series systems.
Proprietary DSP Functions
Excursion Limiting: In addition to signal limiting to protect the amplifier and transducers from overload, the K Series utilizes a proprietary limiter that prevents woofer over-excursion. Over-excursion occurs when a voltage presented to the woofer causes the cone to physically travel too far. This builds up excessive heat, stresses the moving parts of the woofer, produces audible artifacts and distortion and reduces the woofer’s lifespan. The proprietary
ALGORITHMCONTAINEDIN%XCURSION,IMITINGPREVENTSOVEREXCURSION6OLTAGESTHATWILLHARMTHEWOOFERTHROUGHOVEREXCURSIONAREREDUCEDENOUGHTO prevent over-excursion without any audible compression, limiting or loss.
DEEP™: Taking advantage of the Excursion Limiter, the DEEP (Digital Extension and Excursion Processing) algorithm functions as a highly musical and non-distorting low-frequency EQ circuit. More on the DEEP function is available in the EQ section of this manual.
Intrinsic Correction™: Introduced on QSC Concert/Touring products, Intrinsic Correction is a proprietary process and set of signal processing algorithms that address correctable characteristics of transducers and waveguides. The net result is that any K Series system will present extraordinarily even and consistent energy throughout the physical listening area of the loudspeaker, resulting in a very musical, acoustically transparent system.
ENG
DSP User Functions
Low-frequency EQ
On the K8, K10 and K12, there are three low-frequency settings. From the factory, the switch is set to “NORM.”
This means that the loudspeaker system is producing a normal low-frequency signal through the woofer. This is the standard setting for most applications. (Figure 7)
When using one of the top boxes with a subwoofer, the switch should be moved to the “EXT SUB” position to engage the 100 Hz high-pass filter. It is also recommended that the 100 Hz high-pass filter be engaged when using the K10 or K12 as a floor monitor to prevent excessive bass build up on the stage.
For extra low-frequency extension and low-end presence when using one of the top boxes without a sub, move the switch to the “DEEP” setting. This will engage the proprietary DEEP algorithm, providing increased lowfrequency extension without causing distortion or woofer over-excursion.
On the KSub there are two low-frequency settings. From the factory, the switch is set to “NORM.” This means that the subwoofer system is producing a non-EQ’d low-frequency signal through the woofer. This is the standard setting for most applications. (Figure 8)
For extra low-frequency extension and low-end presence, move the switch to the “DEEP” setting. This will engage the proprietary DEEP algorithm, providing increased low-frequency extension without causing distortion or woofer over-excursion.
High-frequency EQ
On the K8, K10 and K12 there are two high-frequency settings. From the factory, the switch is set to “FLAT.” This means that the loudspeaker system is producing a flat response through the vocal band. This is the standard setting for most applications. (Figure 9)
)NVOICEONLYREPRODUCTIONTHESWITCHCANBESETTOTHEh6/#!,"//34vSETTING4HISWILLENGAGE%1THATGIVESA stronger presence for vocal intelligibility and presence. It is generally not recommended to use this setting when playing full-range music through the system.
– Figure 7 –
– Figure 8 –
– Figure 9 –
13
Subwoofer Polarity
Polarity (sometimes improperly referred to as phase) refers to the voltage of an input signal and whether it is a positive or negative voltage at any given time. In most cases a positive voltage causes a woofer cone to move forward with respect to the cabinet orientation, and a negative voltage then moves the woofer cone backward.
Most importantly, speakers reproducing the same signal or signals that are adjacent in frequency must have the same polarity to get the maximum output. This is most important for low frequencies. Polarity can be altered by incorrect wiring or mixer control settings. (Figure 10)
When using the KSub with K Series full range loudspeakers, NORMAL polarity will result in the best bass response
IF the full range loudspeakers are sitting on or very close to the subwoofers. If the subwoofers are some distance away from the full range loudspeakers, polarity change may be of benefit. Start with all subwoofer POLARITY switches in the NORMAL position. Then, with the system at or near expected operating levels, change the polarity
OFEACHSUBWOOFER).$)6)$5!,,97ALKAROUNDTHEVENUEANDASSESSTHEOVERALLBASSRESPONSE3ELECTTHEPOLARITY that results in the best overall system bass response.
When using only one KSub and connecting a LEFT and RIGHT stereo signal, start with the polarity switch in the
NORMAL position. With the system at a reasonable level, change the POLARITY switch and evaluate which polarity results in the most low-frequency output.
ENG
Additional Features
Standby
All K Series models are equipped with an automatic standby feature to conserve energy when the systems are not in use. If no signal is present on any input of a K Series system or the gain knob is turned to off for five minutes, the power amplifier will go into standby and the green STANDBY LED will illuminate. No other LEDs will illuminate when the unit is in standby; this includes both the Rear Power LED and the Front Power LED. In this mode, the amplifier will be powered down. A small amount of voltage will continue to flow from the AC power source into the power supply of the K Series power module. This voltage will keep the power supply and DSP “awake” to reduce turn on time when the system is brought out of standby. The power up time of the amplifier is negligibly small and is shorter than the latency of the DSP, so no signal will be cut off when the K Series system is brought out of standby. A K Series loudspeaker can also be brought out of standby manually by turning the power switch off and then back on.
Front Power LED Functions
The Front Power LED may be set to any of three modes by the rear-mounted Power LED switch. (Figure 11) s From the factory, the Power LED switch is set to the PWR position. The Front Power LED will illuminate when the power switch is in the ON position and the unit is not in Standby. s In the “OFF” position, the Front Power LED will not illuminate. This setting is recommended in applications where the Front Power LED may be visually objectionable while the unit is operating. s In the LIMIT setting the Front Power LED will track the LIMIT LED on the rear of the unit. When the K Series is in Limiting (meaning that one or more of the limiters is engaging to protect some part of the system) the
Front Power LED will glow brighter in response to the limiting function. This allows the system operator to have awareness of the status of the limiters without needing to see the rear of the unit. For more information see the section below on the Rear LIMIT LED. When not in limiting and when the unit is not in standby, the front power
LED will be illuminated dimly.
Rear LIMIT LED
The red LIMIT LED can indicate that limiting has taken place to protect and avoid damage to the amplifier or loudspeaker. (Figure 12) If the signal level at any frequency is too high, the DSP will limit the signal to prevent damage and the red LIMIT LED will illuminate. If the amplifier is too hot because the SPL is too high or the environment is too hot, the red LIMIT LED will be illuminated. If the red LIMIT LED is on when both Gain controls are at minimum, your K Series loudspeaker requires service by qualified personnel.
14
– Figure 10 –
– Figure 11 –
– Figure 12 –
Remote Gain Attenuator
A 3 pin “Euro” connector has been provided to adjust the volume of the K Series loudspeaker or put the system into standby. (Figure 13) By varying the voltage on the PINBETWEEN6PROVIDEDON pin) and ground ( pin), the volume can be linearly controlled. The voltage on the pin can be created by using a potentiometer or provided from an external source. Many K Series systems can be controlled from a single potentiometer by connecting the pins of multiple K Series speakers together.
A relay or manual connection can be made between the pin and the pin to put the K Series system into standby mode after 5 minutes.
WARNING: Do not put more than +5V or less than ground on the pin or else damage may occur. Do not connect the pin directly to the pin.
Schematics of Proper Wiring for Gain Attenuator
When using a single potentiometer for one loudspeaker. (Figure 14)
When using a single potentiometer for multiple loudspeaker. (Figure 15)
Wiring to the 3 pin “Euro” connector. (Figure 16)
– Figure 14 – – Figure 15 – – Figure 16 –
– Figure 13 –
ENG
15
ENG
Applications
Input Hookup
Output Hookup
16
Output Hookup
17
OR
ENG
Common Standalone Small System (Mono)
ENG
Common Stereo System
LEFT RIGHT
18
Dimensions
K8
11"
280 mm
Top
10.6"
269 mm
K10
12.6"
320 mm
Top
11.8"
300 mm
17.7"
450 mm
20.4"
519 mm
Front Side Front
K12 KSub
14"
356 mm
Top
14"
356 mm
23.7"
603 mm
Front Side
19
14"
356 mm
Front
Top
26"
665 mm
28.1"
714 mm
Side
Side
ENG
Specifications
ENG
K8 K10 K12 KSub
Configuration
Transducers
Low-frequency
High-frequency
Trapezoidal 2-way
8" cone transducer
1.75" diaphragm compression driver
Frequency Response (-6 dB) 66 Hz – 18 kHz
Multipurpose 2-way
10" cone transducer
1.75" diaphragm compression driver
60 Hz – 18 kHz
Multipurpose 2-way
12" cone transducer
1.75" diaphragm compression driver
2 x 12" cone transducers
52 Hz – 18 kHz
4th Order Bandpass
48 Hz – 134 Hz
Frequency Range (-10 dB) 61 Hz – 20 kHz
Nominal Coverage (-6 dB) 105° conical
127 dB peak Maximum SPL (1 meter)
Amplifiers
Power Output
Impedance )
1000 W Class D
Controls
Indicators
Connectors
56 Hz – 20 kHz
90° conical
129 dB peak
48 Hz – 20 kHz
75° conical
131 dB peak
44 Hz – 148 Hz
130 dB peak
8,2©KBALANCEDKUNBALANCEDs8,2©-)#MODEBALANCEDs2#!K
0OWERs'AIN!s'AIN"s-IC,INEs,&-ODE%XT3UB.ORM$%%0» s(&-ODE&LAT6OCAL"OOST
Front LED (On/Off/Limit)
0OWERs'AINs,&-ODE.ORMAL
$%%0» s0OLARITY.ORMAL2EVERSE s&RONT,%$/N/FF,IMIT
0OWERs3IGNALs3TANDBYs,IMIT 0OWERs3IGNAL!s3IGNAL"s3TANDBYs,IMITs-IC
"ALANCEDFEMALE8,2©LINEMICLEVELINPUTs"ALANCEDFEMALE8,2©LINELEVELINPUTs$UAL"ALANCEDMALE8,2
FULLRANGELINELEVELOUTs"ALANCEDMALE8,2hMIXvOUTs3TEREO2#!LINELEVELINPUTs2EMOTEGAINCONTROLs,OCKING
IEC power connector
Dual balanced female XLR / ¼"
LINELEVELINPUTs$UAL"ALANCED
MALE8,2FULLRANGELINELEVELOUTs
2EMOTEGAINCONTROLs,OCKING)%# power connector
Cooling On demand, 50 mm variable speed fan
4HERMALLIMITINGs/UTPUTOVERCURRENTs/VERTEMPERATUREMUTINGs'UARD2AIL»
AC Power Input
4HERMALLIMITINGs%XCURSIONLIMITING
5NIVERSALPOWERSUPPLY6!#(Z
AC Power Consumption 6!#!s6!#!s6!#!
Enclosure
Finish
Grille
Dimensions (HWD)
Weight (Net)
Available Accessories
Impact resistant ABS
Black powder coated 18 gauge steel
17.7" x 11" x 10.6"
450 mm x 280 mm x 269 mm
27 lb (12.2 kg)
+4/4%s+9/+%s
K SERIES M10 KIT
20.4" x 12.6" x 11.8"
519 mm x 320 mm x 300 mm
32 lb (14.5 kg)
+4/4%s+9/+%s
K SERIES M10 KIT
23.7" x 14" x 14"
603 mm x 356 mm x 356 mm
41 lb (18.6 kg)
+4/4%s+9/+%s
K SERIES M10 KIT
Painted birch plywood
Black textured paint
26" x 14" x 28.1" (including casters)
665 mm x 356 mm x 714 mm
74 lb (33.6 kg)
+3UB#/6%2
Specifications subject to change without notice.
20
Mailing Address:
QSC Audio Products, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626-1468 USA
Telephone Numbers:
Main Number: 714-754-6175
Sales & Marketing: 714-957-7100 or toll free (USA only) 800-854-4079
Customer Service: 714-957-7150 or toll free (USA only) 800-772-2834
Facsimile Numbers:
Sales & Marketing FAX: 714-754-6174
Customer Service FAX: 714-754-6173
World Wide Web:
qscaudio.com
E-mail:
© Copyright 2009 – 2011, QSC Audio Products, LLC., US D591724, US D609216, Worldwide Patent Pending
QSC™ is a registered trademark of QSC Audio Products, LLC., “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office.
Tilt-Direct, Intrinsic Correction, DEEP and GuardRail are all trademarks of QSC Audio Products, LLC., All trademarks are the property of their respective owners.
K Series User Manual 07/21/11
ENG
K Series
Active Loudspeakers
K8 | K10 | K12 | KSub
Features s ,IGHTWEIGHTPORTABLEPOWEREDSPEAKERSWITHLEGENDARY
13#AMPLIFIERPOWERANDRELIABILITY s WATTCONTINUOUS#LASS$POWERMODULESIN
ALLMODELSX7 s %XTENSIVE$30ENHANCESSYSTEMPERFORMANCE s !TTRACTIVEANDPROFESSIONALAPPEARANCE
s 2UGGED!"3ENCLOSURES++AND+ s 4OURGRADEGAUGESTEELGRILLES s #OMFORTABLEERGONOMICHANDLES s MMPOLESOCKETSWITH4ILT$IRECT ™
FULLRANGEMODELS s -RIGGINGPOINTSFORSUSPENDEDINSTALLATION
FULLRANGEMODELS s +AND+PERFORMASMAIN0!ORSTAGEMONITORS
The QSC K Series is quite simply The New
Standard in lightweight powered loudspeaker systems. For starters, each of the four models features an all new, Pat Quilter designed
1000 watt continuous QSC Class D power module. Next, breaking from the traditional loudspeaker paradigm, every model is fitted with the identical 1.75" HF device (full-range models) and woofers of the same high quality for unparalleled performance, regardless of speaker size.
The LF switch can be set to NORM, DEEP™ for additional bass extension, or EXT SUB (full-range models) for use with an external subwoofer. The rear panel LED switch can be set to POWER, illuminating the front-mounted LED when the unit is powered on, OFF for applications where it is not desirable to illuminate the front LED, or
LIMIT which indicates to the system operator that the clip limiter circuit has been engaged during operation.
Extensive DSP processing is employed throughout, providing levels of sonic clarity and total output that defy the system’s size and weight.
Premium-grade materials, advanced construction processes and multiple mounting and suspension options allow for a wide range of live and installed applications.
Full-range models are housed in rugged ABS enclosures with a professional appearance that is at home in any application. ABS is a far more robust material than conventional speaker plastics and offers an additional measure of sonic clarity due to its internal rigidity.
Ergonomic aluminum handles and a highly protective steel grille complete the package for ease of transport and long term durability.
Combo XLR and 1/4" TRS inputs accept both
Mic and Line Level input while a set of RCA phono inputs (except KSub) allow additional connectivity to portable MP3 players, CD players and line-level mixers. Up to three audio sources can be mixed internally and summed to a balanced output for ”daisychaining” of multiple units. Separate direct outputs are also provided on each channel for additional output flexibility.
The K Series full-range models feature a unique
Tilt-Direct™ pole cup mounting system. A simple turn of the dial engages a 7.5 degree downward tilt of the speaker allowing acoustic energy to be kept on the audience and off reflective surfaces for applications where maximum coverage from a high-positioned speaker is desired. Integrated
M10 suspension points allow for suspended applications with a K SERIES M10 KIT (sold separately) or Yoke bracket (sold separately).
On-board switches provide preset EQ settings.
The HF setting (full-range models) can be set to VOCAL BOOST for additional presence in the critical mid-frequency area or FLAT for accurate reproduction of the incoming signal.
The KSub is a dual-12" bandpass design, constructed of premium birch and includes high-quality, low-noise casters. The subwoofer features a threaded pole receptacle for a positive, wobble free connection to a threaded speaker pole (included).
Remote gain control capability is offered via a potentiometer (not included) connected to the on-board Euroblock connector. In an installed application, multiple K Series speakers can be ”daisy-chained” for total gain control from a single remote pot. Auto-standby mode is engaged after 5 minutes of inactivity.
Extensive DSP s$-4»$IRECTIVITY-ATCHED4RANSITION provides for matched LF and HF coverage across the entire listening area, eliminating unnatural ”dead” or ”hot” frequency zones.
s Intrinsic Correction™, first featured in our high-end line-array products maps 65-75 spacially-averaged measurements to IIR and
FIR filters that actively adjust time, frequency and amplitude response to a maximally flat bandpass target. The result is a speaker that behaves equally well across the entire sound field.
s$%%0»ANDEXCURSIONLIMITINGALLOWFOR extended low-frequency response by actively managing low-frequency transients without degradation of the underlying signal or adjacent frequencies.
s'UARD2AIL»PROTECTIONFIRSTINTRODUCEDON
OUR'83ERIESAMPLIFIERSPROTECTSBOTHTHE amplifier module and your performance from unnatural and destructive clipping.
K Series
Specifications
K8 K10 K12 KSub
Configuration
Transducers
Low-frequency
High-frequency
Trapezoidal 2-way
8" cone transducer
1.75" diaphragm compression driver
Frequency Response (-6 dB) 66 Hz – 18 kHz
Frequency Range (-10 dB) 61 Hz – 20 kHz
Multipurpose 2-way
10" cone transducer
1.75" diaphragm compression driver
60 Hz – 18 kHz
56 Hz – 20 kHz
Nominal Coverage (-6 dB) 105° conical
Maximum SPL 1 127 dB peak
Amplifiers
90° conical
129 dB peak
1000 W continuous Class D (500 W LF, 500 W HF), 2000 W peak
Multipurpose 2-way
12" cone transducer
1.75" diaphragm compression driver
52 Hz – 18 kHz
48 Hz – 20 kHz
75° conical
131 dB peak
4th Order Bandpass
2 x 12" cone transducers
48 Hz – 134 Hz
44 Hz – 148 Hz
130 dB peak
Input Impedance (
Controls
Indicators
Connectors
Ω )
1000 W continuous Class D
(2 x 500 W), 2000 W peak
8,2©KBALANCEDKUNBALANCEDs8,2©-)#MODEBALANCEDs2#!K
0OWERs'AIN!s'AIN"s-IC,INEs,&-ODE%XT3UB.ORM$%%0» s(&-ODE&LAT6OCAL"OOST
&RONT,%$/N/FF,IMIT
0OWERs3IGNAL!s3IGNAL"s3TANDBYs,IMITs-IC
"ALANCEDFEMALE8,2©LINEMICLEVELINPUTs"ALANCEDFEMALE8,2©LINELEVELINPUTs$UAL"ALANCEDMALE8,2
FULLRANGELINELEVELOUTs"ALANCEDMALE8,2hMIXvOUTs3TEREO2#!LINELEVELINPUTs2EMOTEGAINCONTROLs,OCKING
)%#POWERCONNECTOR
0OWERs'AINs,&-ODE.ORMAL
$%%0» s0OLARITY.ORMAL2EVERSE s&RONT,%$/N/FF,IMIT
0OWERs3IGNALs3TANDBYs,IMIT
Dual balanced female XLR / ¼" line
LEVELINPUTs$UAL"ALANCEDMALE
8,2FULLRANGELINELEVELOUTs
2EMOTEGAINCONTROLs,OCKING)%# power connector
Cooling On demand, 50 mm variable speed fan
4HERMALLIMITINGs/UTPUTOVERCURRENTs/VERTEMPERATUREMUTINGs'UARD2AIL»
AC Power Input
4HERMALLIMITINGs%XCURSIONLIMITING
5NIVERSALPOWERSUPPLYn6!#n(Z
AC Power Consumption 6!#!s6!#!s6!#!
%NCLOSURE
Finish
'RILLE
Dimensions (HWD)
Impact resistant ABS
Black powder coated 18 gauge steel
17.7" x 11" x 10.6"
450 mm x 280 mm x 269 mm
27 lb (12.2 kg)
20.4" x 12.6" x 11.8"
519 mm x 320 mm x 300 mm
32 lb (14.5 kg)
23.7" x 14" x 14"
603 mm x 356 mm x 356 mm
41 lb (18.6 kg)
Painted birch plywood
Black textured paint
26" x 14" x 28.1" (including casters)
665 mm x 356 mm x 714 mm
74 lb (33.6 kg) Weight (Net)
Available Accessories +4/4%s+9/+%s
+3%2)%3-+)4
+4/4%s+9/+%s
+3%2)%3-+)4
+4/4%s+9/+%s
+3%2)%3-+)4
+3UB#/6%2
1 For comparison purposes and in accordance with common industry practice, maximum peak SPL specifications are theoretical calculations based upon transducer sensitivity and peak available amplifier power.
2 Independent of limiters and driver protection circuits.
Specifications subject to change without notice.
Amplifier Modules | Applications
K8 | K10 | K12 KSub
K12 Suspended from integrated
M10 installation points.
K12 on speaker stand with Tilt-Direct™ engaged for 7.5 degree down-angle.
K12 and K10 shown in floor monitor position.
K8 over KSub, using K Series speaker pole (included with KSub).
K Series
K8
4OP
11"
280 mm
10.6"
269 mm
K10
12.6"
320 mm
4OP
Dimensions
11.8"
300 mm
17.7"
450 mm
20.4"
519 mm
Front Side Front Side
K12 KSub
4OP 4OP
14"
356 mm
14"
356 mm
14"
356 mm
28.1"
714 mm
23.7"
603 mm
26"
665 mm
Front Side Front Side
Specifications subject to change without notice.
PLEASERECYCLE
© 2009-2011 QSC Audio Products, LLC. All rights reserved. QSC and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries. Tilt-Direct, DMT, Intrinsic Correction, DEEP and GuardRail are all trademarks of QSC Audio Products, LLC. All other trademarks are the property of their respective owners. Patents may apply or be pending.
-AC!RTHUR"OULEVARDs#OSTA-ESA#!s0HORs&AX
K Series Spec Sheet 04/06/11 qscaudio.com

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 1000W Class D power amplifiers
- Advanced DSP processing
- Versatile connectivity options
- Rugged construction
- Multiple mounting and suspension options
- Tilt-Direct™ pole cup mounting system (full-range models)
- Excursion Limiting and DEEP™ algorithms
- Protective limiting circuitry