---HomeUse User Manual
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
FUTV4656 HD/SD Encoder & Modulator
HDMI/YPbPr/S-Video/AV to DVB-T Digital RF
-Ho
meUs
e
User Manual
1 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Thank you for buying this encoder modulator.
Please read this manual carefully to install, use and maintain the encoder modulator in the best conditions of
performance. Keep this manual for future reference.
Directory
CHAPTER 1 Product Introductions........................................................................... 3
General Description................................................................................................. 3
System Connection Chart ........................................................................................ 4
Technical Specifications........................................................................................... 4
CHAPTER 2 Safety Instruction and Installations ...................................................... 6
Safety Instructions................................................................................................... 6
Installations ............................................................................................................. 6
CHAPTER 3 Devices Operations and Management ................................................. 8
Chapter 4 Operations of Record TS and Play TS through USB Disk ....................... 14
Appendix ............................................................................................................... 17
2 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
CHAPTER 1 Product Introductions
General Description
FUTV4656 series encoder & modulator is FMUSER’s consumer electronics which allow audio/video signal
input in TV distributions and video recorded and playback from a USB port with applications in home
entertainment, surveillance control, hotel Digital Signage, shops etc.
It is an all-in-one device integrating MPEG-4 AVC/H.264 encoding and modulating to convert audio/video
signals into DVB-T RF out.
The signals source could be from satellite receivers, closed-circuit television cameras, Blue-ray players, and
antenna etc. its output signal is to be received by a DVB-T standard TV, DVB-T STB etc.
Air Vent
DC 12V HDMI in
Grounding
RF in
RF out
YPbPr/S-Video/AV in
Grounding: to connect the earth cable
DC 12V: power input
HDMI: HDMI stream input supporting HD signals
YPbPr/S-Video/AV: YPbPr/S-Video/AV signal input through a VGA adapter cable
RF in: RF Loop-through input (10 dB attenuation)
RF out: RF output to distribute modulated signal (30-960 MHz, 71~91 dbµV)
3 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
LCD Window
Indicators
Control Buttons
USB Port for Video Record,
Save and Playback
JTAG port for upgrade
System Connection Chart
Technical Specifications
Encoding Section
Encoding
Interface
Video
MPEG-4 AVC/H.264
HDMI
1920*1080_60P,1920*1080_50P;
Resolution
1920*1080_60i, 1920*1080_50i;
1280*720_60p, 1280*720_50P
HDMI
Audio
Bit rate
0.500~19.500 Mbps
Encoding
MPEG1 Layer II, MPEG2-AAC, MPEG4-AAC
Interface
HDMI
Sample rate
48KHz
Bit rate
64, 96,128, 192, 256, 320, 384kbps
4 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Encoding
MPEG-4 AVC/H.264
Interface
CVBS *1, YPbPr*1, S-Video*1
CVBS & S-Video: 720x576_50i (PAL);
Video
YPbPr/
Resolution
720x480_60i (NTSC)
YPbPr: 1920*1080_60i, 1920*1080_50i;
1280*720_60p, 1280*720_50P
CVBS/
S-Video
Audio
Bit rate
0.500~19.500 Mbps
Encoding
MPEG1 Layer II, MPEG2-AAC, MPEG4-AAC
Interface
1*Stereo /mono
Sample rate
48KHz
Bit rate
64, 96,128, 192, 256, 320, 384kbps
Modulator Section
Standard
DVB-T COFDM
Bandwidth
6M, 7M, 8M
Constellation
QPSK, 16QAM, 64QAM,
Code rate
1/2, 2/3, 3/4, 5/6, 7/8.
Guard Interval
1/32, 1/16, 1/8, 1/4.
Transmission Mode:
2K, 8K
MER
≥42dB
RF frequency
30~960 MHz, 1KHz step
RF output level
-16~ -36 dBm (71~91 dbµV), 0.1db step
System
Management
Local control: LCD + control buttons
Language
English
LCN Insertion
yes
Upgrade
JTAG
General
Power supply
DC 12V
Dimensions
153*110*50mm
Weight
< 1kg
Operation temperature
0~45℃
5 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
CHAPTER 2 Safety Instruction and Installations
Safety Instructions
WARNING: Hot plug is not allowed since it may cause system halted.
To prevent fire or electrical shock, do not expose the device to rain or moisture.
The encoder modulator is powered with a voltage of 12V DC. The power supply voltage
must not exceed the recommended voltage, which otherwise may cause irreparable damage to
the device and the invalidation of the warranty. Therefore:
lDo not replace power supply with a voltage greater than 12V DC.
lDo not connect the device to the power if the power cord is damaged.
lDo not plug the device into mains supply until all cables have been connected correctly.
lDo not cut the cord.
Avoid placing the device next to central heating components and in areas of high
humidity.
Do not cover the device with elements that obstruct the ventilation slots.
If the encoder modulator has been kept in cold conditions for a long time, keep it in a warm
room minimum 2 hours before plugging into the mains.
Mount the device in vertical position with the connectors located on the top side.
When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutes may result in fire, electric shock or other hazards.
Safety check- Upon completion of any service or repairs to this device, ask the service
technician to perform safety checks to determine that the device is in proper condition.
Installations
RISK OF damage to the unit
Mechanically handling the unit may result in damage. Do not connect the unit to the power
supply before or during assembly. Connect the unit as below instructed.
NO HOT PLUG!
6 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
1.
Mount
and
tighten
1
the
screws and plugs to secure
the unit to the wall. Left 10
cm of free space around
from each unit.
2.
Connect the signal input in the respective connectors. The signal source can be from a surveillance
monitor, DVD, set-top box, CCTV and etc.
3.
Optionally,
connect the
loop-through RF
input coaxial
5
cable.
4.
3
Connect cable to
RF output to
STB/TV.
2
4
5.
Power supply connection: a) Connect the earth cable; b) Connect the power plug to the unit mains
connector; c) Connect the power plug to the mains socket.
Cascade Installation
FUTV4652 unit has 1 TV signal to RF output encoded as DVB-T Digital TV signal.
Several FUTV4652 units can
be
cascaded
in
order
to
increase the capacity. The
maximum capacity of a series
of N units is 1xN incorporated
TV signals. To cascade 2 or
more units, connect the RF
output of the preceding unit to
the TV input (loop-through) of
the next unit (see right ).
7 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
CHAPTER 3 Devices Operations and Management
FUTV4652 is controlled and managed through the key board and LCD display.
LCD Display – It presents the selected menu and the parameter settings. The backlight in the
display is on when the power is applied.
LED – These lights indicate the working status
l
Power: It lights on when the power supply is connected.
l
Alarm: It lights on when the there is error, such as the signal source loss.
l
Lock: It lights on when the signal source connected and goes off when the signal lose.
Left/Right/Up/Down buttons – Use these buttons to turn the screen pages, shift the target
items by moving the triangle, or change the parameter settings in the program mode.
Enter – Use this button to enter a submenu or save a new setting after adjustment; press it to
start adjusting the value of certain items when the corresponding underline flash with Up and
Hue
+001
►
Enter
►
Hue
+001
►
Hue
1
►
Down buttons;
Hue
+002
Press it to activate the hidden selections and change the setting with Up and Down (or Left
Audio Bit rate Enter
*128
Audio Bit rate
►128
►
Audio Bit rate Enter
128
►
and Right) buttons.
Audio Bit rate
►192
Menu – Press this button to step back
Lock – Locking the screen / cancelling the lock state, and entering the main menu after the
initialization of the device. After pressing lock key, the system will question the users to save
present setting or not. If not, the LCD will display the current configuration state.
When the power is connected, the LCD will start to initialize the program. The LCD menu
goes as below chart.
8 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Initializing
DVB-T 650.000M U
1080 i
6.93Mbps
Main Menu
Status
Main Menu
Encoder
Main Menu
Modulator
Lock
Up
Enter
Down
Menu
1
Status
Alarm
2
Status
Uptime
3
Encoder
Video
Video
Interface
Video In Status
Resolution
.
.
.
Video Norm
Encoder
Audio
Audio
Audio Bitrate
Audio Format
Encoder
Program Info
Program Info
Program Output
Program Name
.
.
.
LCN
EIT Event
VCN
4
5
6
Modulator
Bandwidth
Bandwidth
►8M 7M 6M
7
Modulator
Constellation
Constellation
►64QAM
8
Modulator
FFT
FFT
►2K
9
Modulator
Guard Interval
Guard Interval
►1/32
10
Modulator
Code Rate
Code Rate
►7/8
11
Modulator
RF Frequency
RF Frequency
650.000 MHz
12
Modulator
RF Level
RF Level
-10.0 dBm
13
Modulator
RF On
RF On
Off
*On
14
Modulator
Bit Rate
Bit Rate(val/max)
6.986M/31.668M
15
8K
9 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Main Menu
Stream
Stream
TSID
16
Stream
ONID
17
Stream
NIT
Stream
VCT
Stream
EIT
Main Menu
USB Device
USB Device
Record TS
USB Device
Play TS
Main Menu
System
NIT
Network ID
Network Name
LCN Mode
Private Data
NIT Insert
18
VCT
Modulation mode
VCT insert
19
EIT
Language
EIT Insert
20
Record TS
Start Record
Advanced Config
21
Play TS
File browse
Play mode
22
USB Device
Disk Usage
Total: xx.xxx GB
Free: xx.xxx GB
23
USB Device
Update
Software update?
Yes
►No
24
USB Device
Remove device
Remove device?
Yes
►No
25
System
Save Config
Save Config?
Yes
►No
26
System
Load Saved CFG
Load SavedCFG?
Yes
►No
27
System
Factory Reset
Reset all sets?
Yes
►No
28
System
LCD Time-out
LCD Time-out
►30 s
29
System
Key Password
Set Password
000000
30
System
Lock Keyboard
Lock Keyboard
Yes
►No
31
System
Product ID
0035564905656
70ec8f7b0000f
32
System
Version
Encoder Modulator
SW:0.04 HW:1.5A
33
10 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
1) DVB-T: modulating standard; XX.XXX M: the current output frequency; U: symbol of the
USB disk insertion; 1080i: video resolution of signal source; X.XX Mbps: the current
encoding bit rate
2) Alarm Status: For example, if the signal cable disconnected, it will display Video 1 Not
Lock under this menu.
3) Uptime: It displays the working time duration of the device. It times upon power on.
4) Video Parameters: User can enter the items respectively to set the input interface and view
the video status. User can also adjust values of rest items (Bit rate: 0.500~19.500 Mbps;
Brightness & Contrast & Saturation: 0-255; Hue: -128 - +127).
5) Audio Bit rate: Select audio bit rate among 64, 96, 128, 192, 256, 320, 384 kbps.
Audio Format: Select audio format among MPEG2, MPEG2-AAC and MPEG4-AAC.
6) Program Information: User can enable or disable the program output under menu Program
Output. User can also enter the other items to edit the Service Name, Program Name,
Program Number, and PIDs of PMT, PCR, Video and Audio, and edit LCN (Logical channel
number). EIT Event – User can enter this menu to setup EIT (Event Information Table) for the
current and next program event. The EIT contains Start Year, Start Time, Duration, and Event
Name of the event. All the EIT information can be displayed on the TV screen on condition
that the EIT is chosen to insert (see explanation 20.). VCN – virtual channel number
7) Bandwidth: choose between 6M, 7M and 8M.
8) Constellation: DVB-T modulator contains 3 constellation modes – 64 QAM, QPSK and 16
QAM.
9) FFT (Transmission Mode): Select between 2K and 8K.
10) Guard Interval: Select among 1/32, 1/16, 1/8 and 1/4.
11) Code Rate: It refers to FEC-Forward Error Correction rate. It contains 1/2, 2/3, 3/4, 5/6
and 7/8.
Ø
NOTE: The different combination of bandwidth, constellation, guard interval and code
rate (FEC) will form a different output code rate. Please refer to appendix table 2.
12) RF Frequency: Adjust it at range of 30 to 999 MHz. Set it according your regional
situation or inquire your local services.
13) RF Level: Adjust it at range of -16~ -36dBm.
14) RF On: User can choose to turn on or turn off the RF under this menu.
11 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
15) Bit Rate: User can read the current modulating bit rate and the maximum bit rate
16) TSID: (Transport Stream ID) User can view or adjust after enter this menu.
17) ONID: (Original Network ID)-User can view or adjust after enter this menu.
18) NIT: (Network Information Table) NIT table is a very important table for describing the
network and TS. User can enter the submenus displayed and edit the values or select the LCN
(Logical channel number) mode, and choose whether to insert the NIT. If user chooses to
insert the NIT, information (Network ID, Network Name, LCN Mode, Private Data and LCN
number of the program mentioned in explanation 6) will be added to the transport stream.
Ø
NOTE: when the Private Data is set as 0*0, it is invalid.
19) VCT: Virtual Channel Table. This menu contains two sub-menus, Modulation Mode and
VCT Insert. User can edit modulation mode at the range of 0-255.
20) EIT: EIT Insert - As mentioned above (6), the event information table can be chosen
whether to insert into the TS or not under this menu. If yes, the EIT information set above (6)
will be displayed on the TV screen. Language Code – to set the EIT language For example,
code of the English language is eng. If you set the code as eng, the EIT displayed will be in
English language.
21) – 25) Please refer to Chapter 4 for details.
26) Save Config: Yes/No-to save/give up the adjustment of setting.
27) Load Saved CFG: Yes/No-to load/ not to load the saved configuration.
28) Reset all sets: Yes/No-choose/not choose the factory’s default configuration.
29) LCD Time out: A time limit that LCD will light off. Choose among 5s, 10s, 45s, 60s, 90s
and 120s (seconds).
30) Key Password: User can set a 6-digital password used to unlock the keyboard.
31) Lock Keyboard: Choose Yes to lock the keyboard, then the keyboard cannot be applicable.
It is required to input the password to unlock the key board. This operation is one-off. (If
forgetting your password, please use the universal code “005599”.)
32) Product ID: User can view the serial number of this device. It is read-only and unique
33) Version: It displays the version information of this device. Encoder Modulator: the name
of the device; SW: software version number; HW: hardware version number. User can also
press ENTER again to view the published time of this device.
12 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
13 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Chapter 4 Operations of Record TS and Play TS
through USB Disk
The FUTV4656 encoder modulator has new functions of:
1.
*.ts Video Creation
Download and install the “Creator.exe” application on the PC, users can create a composition
of images, audio and video that can be played back through the device’s USB Port.
Video/Audio/Image files can be supported include:
Image: JPG, PNG, BMP, GIF
Audio: MP3, WAV
Video: MP4, WMV, MPG, TS, AVI
2.
TS Record and Save
Main Menu
USB Device
1)
USB Device
Record TS
Record TS
Start Record
Start Record
►Yes No
Record TS
Advanced Config
Advanced Config
File size
Filter Null PKT
File save mode
File name
Automatic record
Connect the signal source, enter “Start Record” and choose “Yes” to start recording the
encoded TS.
2)
Advanced Config:
File size: users can set the file size for the *.ts to be recorded. A single file can be
maximum 2000M in size.
Filter null PKT: Users can decide whether to filter the null packet for the *.ts files to be
recorded.
File save mode: there are 2 modes provided: “single file” (For example, when the file
size is set as 1000M and the *.ts is recorded up to 1000M, it automatically stops
recording TS.) and “segmented file” (For example, when the file size is set as 1000M and
the *.ts is recorded up to 1000M, it automatically saves the file and continues to record
TS and save it to next file.)
File name: Users can enter this menu to edit name for the *.ts files to be recorded. For
example, if users name it “Record-”, it will give name to the saved *.ts files
14 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
“Record-001.ts”, “Record-002.ts”… “Record-00N.ts”.
Automatic Record: Users can choose whether to set FUTV4656 record the TS
automatically or manually.
3.
TS Playback
Main Menu
USB Device
1)
USB Device
Play TS
Play TS
File Browse
►Record-001.ts
Record-002.ts
Play TS
Play Mode
Play mode
Play all
Loop all
Single file
Single loop
File browse: There is a video list under this menu, choose one file and press “Enter”
button to start play.
2)
Play mode: User can select a play mode for the saved *.ts files as needed before playing
the *.ts file.
When the *.ts is being playing, FUTV4656 LCD will present a playing interface as shown
below.
DVB-T 650.000M
Record-001.ts
DVB-T 650.000MHz
xx.x%
xx.xxM
F
i
l
en
a
m
eb
e
i
n
gp
l
a
y
i
n
g
T
h
ep
l
a
y
e
dp
e
r
c
e
n
t
a
g
eo
ft
h
e
c
u
r
r
e
n
tf
i
l
e
single loop;
A
play all;
A
loop all;
1
S
y
m
b
o
lo
fp
l
a
y-m
o
d
e
T
h
es
i
z
eo
ft
h
ec
u
r
r
e
n
tf
i
l
e
single file
At this time, the key board also plays a different rule
15 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Select file
Stop Playing
Rewind
/Forward
Play
/Pause
4.
Step back to
main menu
Disk Usage
Main Menu
USB Device
USB Device
Disk Usage
Total: xx.xxx GB
Free: xx.xxx GB
Users can enter this menu to view the USB disk’s capacity left.
5.
Update
Main Menu
USB Device
USB Device
Update
Software Update?
Yes
►No
Choose “Yes” to update the FUTV4656 with the update file stored in the USB disk.
6.
Remove Device
Main Menu
USB Device
USB Device
Remove device
Remove device?
Yes
►No
Choose “Yes” to safely remove the USB disk. FUTV4656 will then automatically resume
encoding and playing the program input from the encoder module.
16 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Appendix
Australia Air Channels
Australia Air Channels
Frequency
Ch.
Start
Center
Frequency
End
VHF
C00
C01
C02
C03
C04
C05
C5A
C06
C07
C08
C09
C9A
C10
C11
C12
45
56
63
85
94
101
137
174
181
188
195
202
209
216
223
48.5
59.5
66.5
88.5
97.5
104.5
140.5
177.5
184.5
191.5
198.5
205.5
212.5
219.5
226.5
52
63
70
92
101
108
144
181
188
195
202
209
216
223
230
UHF
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
470
477
484
491
498
505
512
519
526
533
540
547
554
561
568
575
582
589
473.5
480.5
487.5
494.5
501.5
508.5
515.5
522.5
529.5
536.5
543.5
550.5
557.5
564.5
571.5
578.5
585.5
592.5
477
484
491
498
505
512
519
526
533
540
547
554
561
568
575
582
589
596
Ch.
Start
Cente
r
End
C38
596
599.5
603
C39
603
606.5
610
C40
C41
C42
C43
C44
C45
C46
C47
C48
C49
C50
C51
C52
C53
C54
C55
610
617
624
631
638
645
652
659
666
673
680
687
694
701
708
715
613.5
620.5
627.5
634.5
641.5
648.5
655.5
662.5
669.5
676.5
683.5
690.5
697.5
704.5
711.5
718.5
617
624
631
638
645
652
659
666
673
680
687
694
701
708
715
722
C56
722
725.5
729
C57
729
732.5
736
C58
C59
C60
C61
C62
C63
C64
C65
C66
C67
C68
C69
C70
C71
C72
C73
C74
C75
736
743
750
757
764
771
778
785
792
799
806
813
820
827
834
841
848
855
739.5
746.5
753.5
760.5
767.5
774.5
781.5
788.5
795.5
802.5
809.5
816.5
823.5
830.5
837.5
844.5
851.5
858.5
743
750
757
764
771
778
785
792
799
806
813
820
827
834
841
848
855
862
Table 1 Australia Television Frequency/Channels (MHz)
17 / 18
FMUSERI
NTERNATI
ONALGROUPI
NC.广州市汉婷生物技术开发有限公司
Modulation
Constellation
1/4
1/2
2/3
QPSK
16QAM
64QAM
6MHz Bandwidth
Guard Interval
FEC
1/16
1/32
1/4
1/8
1/16
8MHz Bandwidth
Guard Interval
1/4
1/8
1/16
1/32
The weak ability of error-correcting and anti-interference in this area
6.03
5.80 6.45
6.83
7.03
6.64
7.37
7.81
6.03
8.04
3/4
1/8
7MHz Bandwidth
Guard Interval
1/32
6.22
6.58
6.78
6.53
7.25
7.68
7.91
7.46
8.29
8.78
9.05
5/6
6.22
6.91
7.31
7.54
7.25
8.06
8.53
8.79
8.29
9.22
9.76
10.05
7/8
6.53
7.25
7.68
7.91
7.62
8.46
8.96
9.23
8.71
9.68
10.25
10.56
1/2
2/3
7.46
9.95
8.29
11.05
8.78
11.70
9.04
12.06
8.70 9.67
11.61 12.90
10.24
13.66
10.55
14.07
9.95
13.27
11.06
14.75
11.71
15.61
12.06
16.09
3/4
11.19
12.44
13.17
13.57
13.06 14.51
15.36
15.83
14.93
16.59
17.56
18.10
5/6
12.44
13.82
14.63
15.08
14.51 16.12
17.07
17.59
16.59
18.43
19.52
20.11
7/8
13.06
14.51
15.36
15.83
15.24 16.93
17.93
18.47
17.42
19.35
20.49
21.11
1/2
11.19
12.44
13.17
13.57
13.06 14.51
15.36
15.83
14.93
16.59
17.56
18.10
2/3
14.92
16.58
17.56
18.09
17.41 19.35
20.49
21.11
19.91
22.12
23.42
24.13
3/4
16.79
18.66
19.76
20.35
19.59 21.77
23.05
23.75
22.39
24.88
26.35
27.14
5/6
18.66
20.73
21.95
22.62
21.77 24.19
25.61
26.39
24.88
27.65
29.27
30.16
7/8
19.59
21.77
23.05
23.75
22.86 25.40
26.89
27.71
26.13
29.03
30.74
31.67
Table 2 Recommended MPEG-2 Code Rate
18 / 18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising