Advertisement
Advertisement
AUTOMATIC HANDHELD
DIGITAL T
I
RE INFLATOR
MODEL NO. 10963
Automatic Handheld Tire Inflator
Thank you for selecting our Automatic Handheld T i re Inflator, please read this manual carefully before using.
This manual is an important part of this product and should stored safely for future reference. It should be made available for new operators and maintenance personnel.
We reserve the right to change product features at any time.
IMPORTANT
This tire inflator must only be connected to airline systems which have clean dry air. Any moisture in the airline system may cause damage to the operation of this tire inflator and void warranty.
2
Table of Contents
Components List
Features
Introduction
Control Panel
Function and Operation
Troubleshooting
Maintenance
Specifications
Calibration Certificate
5
5 -6
4
5
6-7
8
9
10
1 0
3
Components List
■
Inflator
■
1/4 '' BSP to 1/4 '' NPT adaptor
■
Plug
■
Electrical Adapters * and C harger
( AU, UK, EURO, USA )
■
Hose : 5 ft. | 1.5 m
■
Instruction Manual
* illustrative purposes only
✔
4
Features
■
■
■
■
■
■
■
Auto-off after 90 seconds
Max. pressure 174 psi
Ideal for cars, trucks, bikes etc
Large easy to read LCD display with audible warning
Rechargeable Lithium-ion battery
Tough ABS case
Individually calibrated and tested
(see calibration certificate pg 11)
Introduction
Through the manual the following symbols will be used, this information is for your safety and to prevent damage to this product.
WARNING
The hazard or unsafe practice could result in minor injury
WARNING
The hazard or unsafe practice could result in severe injury or death
Control Panel
KPA BAR PSI KGF O .
O .
O .
0
SET OPS
P1
SET
P2
Button Function
P1: Programmable button
(Initial value 15 psi /1 bar)
P2: Programmable button
(Initial value 30 psi /2.1 bar)
ON/OFF/LIGHT: Power on/
Power off/Light
(+): Increase target pressure, unit change, manual inflation
(-): Reduce target pressure, unit change
(SET): Function Select: Unit change/
OPS set/Manual inflation
5
6
LCD Display
1
2
3
O KPA BAR PSI KGF .
O
SET OPS
.
1. Unit display
2. Pressure display
3. Function select display
4. Working indicator
O .
0
Function and Operation
This device includes the OPS
(Over Pressure Setting) function used to inflate and seat t i res on the rim.
Operation
1. Unit select
The device has four different scales that can be chosen by the user which is kpa /psi /bar /kgf.
Setting the unit here will be the default unit for all future inflation, until changed.
1.1. Press (SET), (SET) will be shown on the LCD screen, and the unit will be flashing.
1.2. Press (+) or (-) to choose the unit.
1.3. Press (SET) to confirm.
4
2. Set OPS (Over Pressure Setting)
2.1. Press (SET) twice, (SET) and (OPS) will be shown on the LCD screen,
(OPS) will be flashing.
2.2. Press (+) or (-) to choose the
OPS value.
2.3. Press (SET) to confirm. If
OPS value is not zero, (OPS) will be displayed on the LCD screen.
3. Manual inflation
If t i re pressure is lower than 3 psi or 0.2 bar, the device will not start automatically.
3.1. Press (SET) three times, the current pressure will be shown on the LCD screen.
3.2 Press (+) to start manually.
4. Set programmable buttons
(P1) initial value is 15 psi /1 bar, (P2) initial value is 30 psi /2.1 bar. The preset pressure value can be reset by the user, setting it here will save it for following usage. But it reverts to the initial value after a unit set change.
1. Press (P1) or (P2), (P1) preset value or
(P2) preset value will be shown on the
LCD screen.
2. Press (+) or (-) to choose preset pressure value.
3. Press (SET) to confirm.
5. Inflation and Deflation
1.
Press (P1) or (P2) to select default preset pressure.
2.
Press (+) or (-) to adjust target pressure.
3.
Connect with t i re, ensure no air leaks, inflator will start automatically.
4.
When inflation is finished, the device will stop automatically and BEEP to remind the user.
5.
Disconnect the air hose from t i re.
6.
Power on/Power off/Backlight
When battery indicator is flashing on the
LCD screen please recharge the battery.
Press (ON/OFF/LIGHT) two seconds to turn on.
Press (ON/OFF/LIGHT) to turn on backlight when the device is on.
Press (ON/OFF/LIGHT) for three seconds to turn off.
Notes:
1.
Press (SET) to enter the function setting mode. After selecting the unit, press
(SET) again to enter the (OPS) setting.
2.
Press (SET) four times and the device will exit out of the setting mode without saving any selection.
3.
When OPS function is selected the device will inflate to target pressure plus the OPS value first, then deflate to t i re pressure desired, for example: A final target of 32 psi or 2.2 bar with an OPS setting of 16 psi or 1.1 bar gives a sum of
48 psi or 3.3 bar. This sum of 48 psi or
3.3 bar is the Over Pressure Setting for t i re. The t i re will inflate to the sum value and deflate to the final target pressure.
4. During inflation, the device will check t i re pressure automatically, the working indicator will be on, left to right means inflating, right to left means deflating.
WARNING
To avoid the risk of personal injury, especially to the eyes, face or skin.
DO NOT direct the air stream at any person
WARNING
This equipment is not intended for use by children without adult supervision
WARNING
When using the OPS function the sum pressure must not exceed the tyre manufacturer’s maximum inflation pressure.
7
Troubleshooting
PROBLEM
Air leak
The inflator works, but no air is flowing
No display
Inflation does not start, although the pressure is set and the hose is connected with tyre
Err1
Err2
Err3
Err4
Err5
Err8
POSSIBLE CAUSE
Leak in the connection
Obstruction in filters or in air system
Flat battery
Air hose improperly connected
SOLUTION
Check the connection
Clean the filters and check the air source
Recharge battery
Check the hose connection, make sure that no air leaks
T i re pressure is below
0.2 bar (3 psi)
Pressure sensor broken
Manual inflation
Power off, change pressure sensor
Replace hose connector or re-connect hose to the t i re
Unstable pressure, faulty hose connector
Connected tyre pressure is too high 12.5 bar (180 psi)
Wrong connections at air inlet and outlet
Stop inflating this t i re
Refer to wiring diagram and connect magnetic valve accordingly
Battery low
Air supply lower than set inflate pressure
Please recharge the battery
Stop inflating this t i re
Maintenance
The device does not require particular maintenance, routine check of the air connections is suggested.
In the event that maintenance is required it should be carried out by qualified personnel.
Warranty Note
■
This unit must be used with clean dry air. Therefore an air filter and or water trap must be used with this unit to ensure its continued reliability.
■
Moist air entering this unit will affect the pressure sensors and may cause the electronics to fail.
■
Please ensure only airline systems with clean dry air are connected to this t i re inflator.
■
Product warranty will be void if moisture enters the t i re inflator.
Specifications
■
■
■
■
■
■
■
■
■
Scale
0.5-12 bar /1200 kpa
174 psi /12 kgf
Accuracy
± 2 psi @ 25-75 psi
Max Inlet Air Supply
12.5 bar (180 psi)
Supply Voltage
DC 12V rechargeable battery (Li-ION)
Charger Voltage
AC 110~240 V (50~60Hz)
Watt
12W Max.
Working Temperature
-10~50 ° C (14~122 ° F)
Auto Off
90 seconds
Hose Length
5 ft. | 1.5 m
■
■
■
■
■
■
■
■
■
Inlet Size
1/4'' BSP
Chuck Type
Clip on
Chuck Style
Single straight
Reader Unit
Digital display with audible warning
Dimensions
380 x 125 x 135 mm
Weight
2 kg
Operation
Auto inflate/deflate
Inflation Flow
2500 l/m @ 145 psi
Work Time Hrs
10-15 hrs (from fully charged continual use)
Calibration Certificate
This Automatic Handheld T i re Inflator has been calibrated in its normal working position on test equipment with an accuracy that is traceable to International Standards according to: 86/217/EEC.
ALLOWABLE TOLERANCE
BAR
±0.08
±0.16
up to and including 4 bar between 4 bar and 10 bar inclusive
PSI
±0.25
±1.2
±2.3
±3.6
greater than 10 bar up to and including 58 psi between 58 and 145 psi inclusive greater than 145 psi
TEST RESULT
REFERENCE PRESSURE
BAR PSI
DISPLAY PRESSURE
BAR PSI
Serial Number:
Date:
Distributed by
ESCO - Equipment Supply Co.
15270 Flight Path Drive, Brooksville FL, 34604 [email protected]
1-800-352-9852
For more information contact Customer Service on
10 www.
esco .net

Public link updated
The public link to your chat has been updated.
Advertisement