Honda 08E95-MCA-102 Installation Instructions Manual 8 Pages
Honda 08E95-MCA-102 is a CB radio kit designed for the Honda GL1800 motorcycle. It allows for hands-free communication with other CB radios within range, enhancing safety and convenience during rides. The kit includes a CB radio, mounting hardware, and a detailed installation guide. With its user-friendly design and clear audio, the Honda 08E95-MCA-102 CB radio kit seamlessly integrates into your motorcycle, providing a reliable and efficient communication solution.
advertisement
Accessory Application Publications No.
INSTALLATION
INSTRUCTIONS
CB RADIO KIT
P/N 08E95-MCA-102
GL1800
Honda Dealer: Please give a copy of this instruction to your customer.
PARTS LIST
(5)
(6)
(7)
Issue Date
February 2007
TOOLS AND SUPPLIES REQUIRED
Phillips ® screwdriver
Electric drill motor
Drill bit (7, 10 mm)
Hole saw (28 mm)
Scissors
Wood block
Isopropyl alcohol
Torque wrench
(4)
(1)
USE AND CARE INFORMATION
The combined weight of the cargo and accessories must not exceed the maximum weight capacity of the trunk:
CB Radio Kit 1.6 lbs (0.7 kg)
(10)
(8)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
No.
(1)
(2)
(3)
(9)
(10)
CB radio
Owner’s Manual
Description
FCC Rule Book
Grommet
Cushion tape
Plate
Rivet
Capacitor (2P)
Capacitor (2P waterproof)
Wire tie
(9)
1
4
2
1
4
Qty
1
1
1
1
3
© 2007 American Honda Motor Co., Inc - All Rights Reserved.
08E95-MCA-1002-91
1 of 8
INSTALLATION
NOTE:
• These instructions are for installation of the CB radio.
For operation of the CB radio, refer to the Owner’s
Manual and FCC Rule Book furnished with the CB radio.
• Install the antenna which is sold separately between the installation of the rear trunk and the routing of the wire harness.
• It is not necessary to drill four 7 mm holes and install the plate when you are also installing the CD changer.
1.
Refer to the Service Manual to remove the right and left side covers and disconnect the negative terminal from the battery.
SEAT
RIGHT
PASSENGER
GRIP
BOLT
LEFT PASSENGER
GRIP
LEFT SIDE
COVER
2.
Remove the meter panel from the motorcycle as indicated in the Service Manual.
- Up to '05 model year -
LEFT SPEAKER
COVER
CLIP
RIGHT SPEAKER
COVER
BOLT
SWITCH COVER
METER PANEL
- From '06 model year -
METER PANEL
RIGHT SIDE
COVER
2 of 8
08E95-MCA-1002-91 © 2007 American Honda Motor Co., Inc - All Rights Reserved.
- Airbag Type -
METER PANEL
- From '06 model year -
CLIP
LEFT FRONT
SCREW
FRONT SHELTER
CENTER
SHELTER LID
Remove.
LEFT
SHELTER
SWITCH
PANEL
CLIP
SCREW
RIGHT
COWL TRIM
MOULDING
Also remove the left side.
3.
Remove the parts from the motorcycle as indicated in the Service Manual.
- Up to '05 model year -
CLIP
RIGHT FRONT POCKET
Also remove the left side.
- Airbag Type -
CLIP
AUDIO &
HAZARD
SWITCH
LEFT FRONT
NAVIGATION
PANEL SWITCH
SCREW
LEVELING
SWITCH
SCREW
RIGHT SHELTER
SWITCH PANEL
Also remove the left side.
SCREW
RIGHT COWL TRIM
MOULDING
Also remove the left side.
© 2007 American Honda Motor Co., Inc - All Rights Reserved.
08E95-MCA-1002-91
RIGHT
COWL TRIM
MOULDING
Also remove the left side.
3 of 8
4.
Remove the shelter from the motorcycle as indicated in the Service Manual.
- Up to '05 model year -
SCREW
SOCKET BOLT
Also remove the left side.
SOCKET BOLT
Also remove the left side.
- Airbag Type -
SOCKET BOLT
SOCKET BOLT
WASHER
LEFT TOP
SHELTER
Remove.
SHELTER
Remove.
SOCKET BOLT
Also remove the left side.
SOCKET
BOLT
Also remove the left side.
RIGHT
TOP
SHELTER remove.
SOCKET BOLTS
Also remove the left side.
SOCKET BOLT
Also remove the left side.
NUT
Also remove the left side.
- From '06 model year -
SCREW
SOCKET BOLT
Also remove the left side.
SOCKET
BOLT
Also remove the left side.
NUT
Also remove the left side.
5.
Remove the rear trunk as indicated in the Service
Manual.
BOLT
WASHER
REAR TRUNK
SHELTER
Remove.
SOCKET BOLTS
Also remove the left side.
NUT
Also remove the left side.
4 of 8
08E95-MCA-1002-91 © 2007 American Honda Motor Co., Inc - All Rights Reserved.
6.
Locate the mark on the back of the trunk. Using an electric drill motor and hole saw, drill a 28 mm hole through the mark as shown.
• Remove any burrs from the edge of the hole.
8.
Attach the cushion tapes on the CB radio as shown.
ISOPROPYL
ALCOHOL
CUSHION TAPE
Remove the paper backings from the adhesive before attaching.
ELECTRIC DRILL MOTOR
(28 mm HOLE SAW)
MARK
7.
Inside the rear trunk, locate the four marks. Drill a hole through each mark using an electric drill motor and 7 mm drill bit.
• Do not drill the 7 mm holes if you are installing the CD changer.
• Remove any burrs from the edge of the hole.
MARKS
CB RADIO
9.
Install the CB radio in the rear trunk.
GROMMET
Insert into the drilled hole.
CB RADIO
ELECTRICAL TAPE
150 mm
REAR TRUNK
SLIT
GROMMET
10. Install the plate on the rear trunk if you are installing the CD changer.
ELECTRIC DRILL
MOTOR (7 mm BIT)
© 2007 American Honda Motor Co., Inc - All Rights Reserved.
08E95-MCA-1002-91
5 of 8
11. Reinstall the trunk lid being careful not to pinch the wire harness.
HOLES drilled in step 7.
RIVET
PLATE
13. Route the CB radio harness as shown.
ANTENNA LEAD
(Sold separately)
CB RADIO ANTENNA
MOTORCYCLE’S
3-PIN CONNECTOR
(White)
HOLES drilled in step 7.
CB RADIO
12. Remove the right and left duct as shown.
• This step is for airbag type only.
CLIP
Right side
RIGHT DUCT
CB RADIO 3-PIN
CONNECTOR
MOTORCYCLE’S
13-PIN CONNECTOR
(White)(unused)
CB RADIO HARNESS
Left side
CLIP
LEFT DUCT
CB RADIO HARNESS
Airbag Type (right side)
13-PIN CONNECTOR
13-PIN
CONNECTOR
6 of 8
08E95-MCA-1002-91 © 2007 American Honda Motor Co., Inc - All Rights Reserved.
14. Connect the capacitor as shown.
CAPACITOR
(2P WATERPROOF)
MOTORCYCLE’S
2-PIN CONNECTOR
CAPACITOR (2P)
After the connection, store the capacitor in the harness boot.
Airbag Type (left side)
MOTORCYCLE’S
2-PIN CONNECTOR
(White)
CAPACITOR (2P)
After the connection, store the capacitor in the harness boot.
MOTORCYCLE’S
2-PIN CONNECTOR
(White)
Airbag Type (right side)
CAPACITOR (2P)
After the connection, store the capacitor in the harness boot.
CAPACITOR (2P)
After the connection, store the capacitor in the harness boot.
© 2007 American Honda Motor Co., Inc - All Rights Reserved.
08E95-MCA-1002-91
MOTORCYCLE’S
2-PIN CONNECTOR
(White)
7 of 8
15. Cut the two cushion tapes into halves.
CUSHION TAPE
SCISSORS
16. Secure the wire harness with the wire ties and cushion tapes in the areas shown.
CUSHION TAPE
Thoroughly clean the area where the cushion tape will be attached and remove the adhesive backing before attaching.
WIRE TIE
Secure the CB radio harness to the frame.
17. Reinstall the fuel tank cover, meter panel, side moldings and side covers being careful not to pinch the wire harness.
18. Reconnect the negative cable to the battery.
19. Reinstall the seat in the reverse order of removal.
8 of 8
08E95-MCA-1002-91 © 2007 American Honda Motor Co., Inc - All Rights Reserved.
advertisement
Related manuals
advertisement