DoorHan RCBLACK-4 Installation Manual
DoorHan RCBLACK-4 is a 12V, 4-channel remote control transmitter with a working frequency of 433.25 MHz. It can be used to operate up to four different DoorHan devices, including gates, barriers, and other automatics. The transmitter has a range of up to 100 meters and can be programmed with up to 16 different codes. It also features a low battery indicator and a built-in LED flashlight.
Here are some possible use cases for the DoorHan RCBLACK-4:
- Controlling gates and barriers: The RCBLACK-4 can be used to open and close gates and barriers from a distance of up to 100 meters. This can be useful for controlling access to a property or for automating the opening and closing of gates and barriers.
Advertisement
Advertisement
иНсТрукция По
ПрограммироваНию раДиоПульТа RCBLACK-4
1. НазНачеНие
Радиопульт DoorHan предназначен для дистанционного управления автоматикой DorrHan, а также автоматикой других производителей при условии использования внешнего приёмника DoorHan
DHRE2. Пульт имеет 4 радиоканала и позволяет управлять четырьмя устройствами.
2. ТехНические харакТерисТики модель
Батарея питания частота количество каналов
Диапазон рабочих температур
RCBLACK-4
12V, type 27A
433,25 MHz
4
-20 °С ... +50 °С
3. ПрограммироваНие
Программирование пультов с приемником DHRE-2
1) Перед началом программирования можно очистить память приемника от записанных ранее кодов пультов (рекомендуется при первой настройке). Для этого после включения питания удерживайте кнопку записи пультов нажатой 10 секунд (SW1 - если используется разъем приемника CH1, SW2 - если используется CH2). Индикатор
LED1 будет мигать 10 секунд, затем потухнет на 2 секунды и снова дважды мигнет в подтверждение стирания записанных в память кодов.
2) Для записи кода пульта нажмите и удерживайте в течение
3 секунд кнопку «SW1»на плате радиоприемника - для настройки электропривода, подключенного к выходу CH1, кнопку «SW2» - для настройки электропривода, подключенного к выходу CH2, при этом загорится индикатор LED1 на приемнике. После этого нажмите необходимую кнопку на пульте ДУ на 2-3 секунды. Внимание! после проведения процедуры в память радиоприемника записывается только одна кнопка.
3) Для настройки нескольких пультов повторите запись кода для других пультов.
1
3
2
4
Программирование пультов со встроенным приемником электропривода SE-750/1200
1) Перед началом программирования можно очистить память приемника от записанных ранее кодов пультов (рекомендуется при первой настройке). Для этого нажмите и удерживайте кнопку «R». У
Вас на дисплее появится «0». Держите кнопку «R» нажатой до тех пор, пока «0» не пропадет с дисплея.
2) Каждой из кнопок на пульте соответствует определенный канал управления (рис.), выбор которого осуществляется в 5-м пункте программирования («Установка кнопки управления»). По умолчанию привод настроен на 1 или 2 кнопку - в зависимости от программы контроллера.
3) Для записи кода пульта нажмите кнопку «R». В левой части дисплея появится «0» и сразу исчезнет. Дважды нажмите кнопку на пульте.
4) Остальные пульты программируются аналогично.
Компания “DoorHan” благодарит Вас за приобретение нашей продукции. Мы надеемся, что Вы останетесь довольны качеством данного изделия. По вопросам приобретения, дистрибьюции и технического обслуживания обращайтесь в офисы региональных представителей или центральный офис компании по адресу: россия, 143002 московская обл., одинцовский район, с. акулово, ул. Новая, д. 120
Тел: +7 (495) 933–2400, 981–1133
E-mail: [email protected]
www.doorhan.ru
InStALLAtIon mAnUAL
RCBLACK-4
EC DECLARAtIon of ConfoRmItY
We: DoorHan Europe s.r.o.
Bozeny Nemcove 1689, 43201 Kadan, Ceska Respublika Herewith declare under sole responsibility that:
• Declares that:
The device model RCBLACK-4
• complies with the essential safety requirements of the following directives:
73/23/EEC and subsequent amendment 93/68/EEC
89/336/EEC and subsequent amendment 92/31/EEC and
93/68/EEC
Additional note:
These products have undergone tests in a typical uniform configuration
(all products manufactured by DoorHan Europe s.r.o.)
01/03/2010 Mikhail Kiselev Managing Director
Date signature
1. DESCRIptIon
Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter.
2. tECHnICAL SpECIfICAtIonS model
Battery
Working frequency
Quantity of channels
Working temperature range
RCBLACK-4
12V, type 27A
433,25 MHz
4
-20 °С ... +50 °С
3. pRogRAmmIng programming of the remote controls with reciever DHRE-2
1) Before programming the former codes can be erased from the memory of the recipient (it is recommended by the first setting). In order to do that, hold down the key 10 sec (SW1 for connector CH1, SW2 for connector CH2). The indicator LED1 will blink for 10 sec, then it will go out for 2 sec and blink twice to confirm erasing of the codes.
2) To record the new code hold down for 3 sec the key «SW1» on the recipient card, to make settings of the electric operator connected to the output CH1 and the key «SW2» - to make settings of the electric operator connected to the output CH2, at that the indicator LED1 will light. After that press the necessary key on the remote control unit for 2-3 sec. Attention! after the operation is completed only one key can be stored in the memory of the recipient.
3) To make settings for other remote controller repeat record procedures with other remote controllers.
1
3
2
4 programming of the remote control units with build-in electric operator SE-750(1200) reciever.
1) Before programming the former codes can be erased from the memory (it is recommended by the first setting). In order to do that, press and hold down the key «R». The «0» will appear on the display. Hold down the key «R» until the «0» disappears.
2) For each of the buttons there is a certain control channel (pic.), which selection operation is described in Item 5 («Control key setting»).
The operator's default control button is key 1 or key 2 depending on the controller's program.
3) To record the code of the remote controller press the key «R». On the left part of the display the “0” will appear and disappear immediately.
Press the key on the remote controller twice.
4) Other remote control units are programmed in a similar way.
For removal of transmitter from memory of the receiver: Press and keep during 8 with pressed button R, the indicator (zero in the bottom of the display will not go out yet, the short sound signal will thus be distributed. For other information use the manual of door operator.

Public link updated
The public link to your chat has been updated.
Advertisement