TWIN SHOWER SYSTEM
Installation Guide
Technical Specifications:
Important Installation Considerations
Important Installation Considerations
1. NOTE: Some showers may not provide an effective shower when used with gravity fed heated water systems or where pressures are less than 150kPa at the outlet. Additionally showers with flow rates of less than 150kPa at the outlet. Additionally showers with flow rates of less than 9L/min may not allow the following to function correctly:
_ some tempering valves
_ some thermostatic mixing valves
2. Some shower heads only operate correctly when hot and cold water
2. Some shower heads only operate correctly when hot and cold water supplies are both mains pressure and may not be suitable for some instantaneous hot water services.
3. When water pressure is in excess of 500kPa a pressure limiting device is required in accordance with AS/NZS 3500 1.12 recommendation is required in accordance with AS/NZS 3500 1.12 recommendation
Operating Pressure:
Min: 150kPa/1.5bar
Max: 500kPa/5.0bar*
Optimum: 150kPa/1.5bar - 500kPa/5bar
Posh Domaine Twin Rail Shower Chrome (3*)
Operating Temperature:
Hot: Max 80°C*
Cold: Min 5°C
Inlet Connections:
Hot: Max 80°C*
Cold: Min 5°C
97-3057
Operating Pressure:
Min: 150kPa/1.5bar
Operating Temperature:
Inlet Connections:
All ½" BSP
NOTE:
- After installation all connections must be
checked for leaks - After installation all connections must be
- All installations must be carried out in
compliance with relevant water regulations*.
compliance with relevant water regulations*.
1.
WATER INLET: RECOMMENDED MINIMUM HEIGHT OF
1800mm FROM FLOOR LEVEL
Min 13±2mm
2.
* Regional specific regulations apply.
www.methven.com
Connector
3.
Please refer to your warranty statement at www.methven.com
Water Inlet
Connector
4.
Top Rail
Bracket
1.
WATER INLET: RECOMMENDED MINIMUM HEIGHT OF
1800mm FROM FLOOR LEVEL
Min 13±2mm
2.
Max
Methven warrants this product against manufacturing defects and that it is suitable for use under the general operating conditions specified in this instruction sheet. However, regional regulations apply and may affect your warranty. Please refer to customer service for full details.
customer service for full details.
New Zealand
0800 804 222
New Zealand
0800 804 222
98-0284
Australia
1300 638 483
Australia
1300 638 483
Install a ½" male threaded connection at the recommended height on wall, ensuring that a minimum of 13±2mm of thread protrudes past the finished wall.
Correct water proofing must be applied.
UK
0800 195 1602
UK
0800 195 1602
Loosen the 2 grub screws with the Allen Key supplied and remove Water Inlet Connector from diverter.
ISSUE A
DECEMBER 2015 and screw Water Inlet Connector onto the ½” connector.
ISSUE A
DECEMBER 2015
Bottom Rail
Connector
Bottom Rail
Bracket www.methven.com
making sure it is vertically in line with the top rail connector. Maximum centre distance between the top and bottom shower connections is 800mm.
www.methven.com
brackets onto the top and bottom rail connectors until they are against wall. Secure with grub screws.
Water Inlet
Connector Water Inlet
Connector
Top Rail
Bracket
CLEANING
Water contains lime which remains on the surface after the water has evaporated. These lime deposits can be prevented from forming by wiping immediately after use.
To clean the chrome-plated surfaces use a soft cloth, soap and warm water. Never use cleaning agents that contain a corrosive acid or a scouring additive.
Max
○ 25mm
Filter Washer
Ball Joint
Bottom Rail
Connector
Install a ½" male threaded connection at the recommended height on wall, ensuring that a minimum of 13±2mm of thread protrudes past the finished wall.
Correct water proofing must be applied.
5.
Bottom Rail
Bracket
Loosen the 2 grub screws with the Allen Key supplied and remove Water Inlet Connector from diverter.
Apply thread tape (or Similar) to the ½’” connection and screw Water Inlet Connector onto the ½” connector.
6.
Screw the bottom rail connector to a wall stud
Connect the round nut at the bottom of the overhead tube to the upside outlet of the diverter top and bottom shower connections is 800mm.
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on wet rail, attach handset and place firmly in holder. Tilt and rotate until they are against wall. Secure with grub screws.
CLEANING
Instructions are left with the end user for future reference
Water contains lime which remains on the surface after the water has evaporated. These lime deposits can be prevented from forming by wiping immediately after use.
To clean the chrome-plated surfaces use a soft cloth, soap and warm water. Never use cleaning agents that contain a corrosive acid or a scouring additive.
Page 1 of 2
Do not use any sharp objects to clean nozzles
Clean filter washer periodically.
Filter Washer
Ball Joint
Clean filter washer periodically.
Do not use any sharp objects to clean nozzles
Connect the round nut at the bottom of the overhead tube to the upside outlet of the diverter valve body.
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on wet rail, attach handset and place firmly in holder. Tilt and rotate head to the desired position.
1.
WATER INLET: RECOMMENDED MINIMUM HEIGHT OF
1800mm FROM FLOOR LEVEL
Min 13±2mm
2.
Water Inlet
Connector
3.
Water Inlet
Connector
4.
Top Rail
Bracket
Bottom Rail
Connector
Install a ½" male threaded connection at the recommended height on wall, ensuring that a minimum of 13±2mm of thread protrudes past the finished wall.
Correct water proofing must be applied.
5.
Bottom Rail
Bracket
Loosen the 2 grub screws with the Allen Key supplied and remove Water Inlet Connector from diverter.
Apply thread tape (or Similar) to the ½’” connection and screw Water Inlet Connector onto the ½” connector.
6.
Screw the bottom rail connector to a wall stud making sure it is vertically in line with the top rail connector. Maximum centre distance between the top and bottom shower connections is 800mm.
CLEANING
Water contains lime which remains on the surface after the water has evaporated. These lime deposits can be prevented from forming by wiping immediately after use.
Check the grub screws are wound out. Push the rail brackets onto the top and bottom rail connectors until they are against wall. Secure with grub screws.
To clean the chrome-plated surfaces use a soft cloth, soap and warm water. Never use cleaning agents that contain a corrosive acid or a scouring additive.
Filter Washer
Ball Joint Clean filter washer periodically.
Do not use any sharp objects to clean nozzles
1.
WATER INLET: RECOMMENDED MINIMUM HEIGHT OF
1800mm FROM FLOOR LEVEL
Min 13±2mm
2.
Water Inlet
Connector
3.
valve body.
Water Inlet
Connector
Make sure a washer is in both ends of the hose.
4.
head to the desired position.
Top Rail
Bracket
Max
○ 25mm
Bottom Rail
Connector
Install a ½" male threaded connection at the recommended height on wall, ensuring that a minimum of 13±2mm of thread protrudes past the finished wall.
Correct water proofing must be applied.
5.
Bottom Rail
Bracket
Loosen the 2 grub screws with the Allen Key supplied and remove Water Inlet Connector from diverter.
Apply thread tape (or Similar) to the ½’” connection and screw Water Inlet Connector onto the ½” connector.
6.
Screw the bottom rail connector to a wall stud making sure it is vertically in line with the top rail connector. Maximum centre distance between the top and bottom shower connections is 800mm.
CLEANING
Water contains lime which remains on the surface after the water has evaporated. These lime deposits can be prevented from forming by wiping immediately after use.
Check the grub screws are wound out. Push the rail brackets onto the top and bottom rail connectors until they are against wall. Secure with grub screws.
To clean the chrome-plated surfaces use a soft cloth, soap and warm water. Never use cleaning agents that contain a corrosive acid or a scouring additive.
Filter Washer
Ball Joint
Clean filter washer periodically.
Do not use any sharp objects to clean nozzles
Connect the round nut at the bottom of the overhead tube to the upside outlet of the diverter valve body.
Make sure a washer is in both ends of the hose.
Screw hose onto lower outlet on wet rail, attach handset and place firmly in holder. Tilt and rotate head to the desired position.
Page 2 of 2
