Chile
5FT Bed
Assembly Instructions
- Please keep for future reference
498/7260
497/0648
Dimensions
Width - 158,1cm
Depth - 207.6cm
Height - 112,8cm
Important
– Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, c a l l t h e Customer Helpline: 03456 400 800
Issue 1 - 05/10/15
1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the components and tools listed on pages 2 and 3.
Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area, small parts could choke if swallowed.
Make sure you have enough space to layout the parts before starting.
Do not stand or put weight on the product, this could cause damage.
Assemble the item as close to its final position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your floor.
This product has been produced from natural timber; you may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
We do not recommend the use of power drill/drivers for inserting screws , as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be easier with 2 people.
The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture.
Dispose of all packaging carefully and responsibly.
On unpacking the furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time.
This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing or carpeted surfaces during assembly.
Care and maintenance
Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product.
Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age.
From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
1 Headboard (112.8 x 158.1cm)
2 Footboard (61.8 x 158.1cm)
3 Side rail x 2 (200.0 x 14.0cm)
4 Central rail (199.3 x 6.5cm)
5 Slats x 12 (152 x 7.0cm)
6 Middle support x 02 ( 26.0 x 6.5cm)
2
3
Components - Fittings
If you have damaged or missing components, call the Customer Helpline: 03456 400 800
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly.
In some cases more fittings may be supplied than are required.
A
Wooden dowel x 4
10 x 50mm
D
4 x 35mm Screw x 24
B
3.5 x 16mm Screw x 8
E
Headless bolt 1/4 x 75mm x 4
C
4.5 x 60mm Screw x 4
G
Half moon nut 1/4 x 4
K
Washer x 4
Cod. 330103
N
89mm Spacer x 2
H
Nut 1/4 x 4
L
Spanner
F
1/4 x 80mm Bolt x 4
Cab. 17
J
Metal bracket x 2
M
Allen key x 1
Tools required
Phillips screwdriver
(medium & large)
2 m
Ruler/tape measure
Small hammer
Eye protection
(when using a hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step
1
Fixing metal brackets.
the pre drilled holes in
1
J
B
J
B
Step
2
Screw headless bols E
E
E
E
4
5
Assembly Instructions
Step
3
Assembling central rail and inserting dowels.
Attach the pre drilled holes in the middle supports 6
C
4
C
6
6
Step
4
2x
3
A
A
Assembly Instructions
Step
5
Assembling side rails.
Important:
Two people are required for an easier assembly.
1
With help, fit one side 3
Insert half moon nuts G as shown, then fix parts using bolts F and allen key
M .
3 side rail.
M
F
3
G
3
Step
6 side rails. Fit the headless bolts in the footboard thought the washers. b: Fix headless bolts E
. a
L
K
K
H
H
L
L b
Assembling of will be easier with 2 people. It can also avoid damages or brakes of any part or component.
2
6
Assembly Instructions
Step
7 metal brackets in the headboard and footboard
B
B
4
B
Step
8
Assembling slats
Please fix the first slat at the end of the rail and work towards the middle of the bed using ensure correct spacing.
Fix slats in one side first, then fix them in the other side by pushing the rail against the slats if necessary.
D
D
D
D
D
D
D
N
D
D
D
D
D
D
D
D
D
D
D
D
D
D
5
D
D
D
D
Assembly is complete.
7
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
