Stanley SXAC1521121 air compressor User manual

AIR COMPRESSOR

1.5HP 21L

MODEL NO.

SXAC1521121

For service, spare parts or product information, please contact Smart Marketing Group Pty. Ltd.

AUST. 1300 660 457 N.Z. 0800 474 876

SUGGESTED APPLICATIONS

You may use some light duty air tools with this compressor.

Some examples of light duty tools are:

• Ball Inflator

• Toy Inflator

• Tyre Inflator

• Mini Air Brush

• Touch Up Spray Can

• Stapler

• Combo Nailer

• C-Bradder

• T-Nailer

This light duty air compressor is NOT recommended for use with a spray gun. Always check the air requirement of the tool wishing to be used to ensure that it is within this air compressor’s air output.

CONTENTS

Section

Contents

Suggested Applications

Introduction

Guarantee

General Safety Instructions

Electrical Information

Specific Safety Instructions

Components and Controls

Operating Instructions

Maintenance

Trouble Shooting

Parts Diagram

Technical Information

Contact Information

9

10 – 15

16

16

17

18

18

3 – 4

5 – 7

8

8

Page

2

2

3

Please take note of serial number and write here for ease of reference:

Serial Number:

Date of Purchase:

Place of Purchase:

Receipt Number:

2 3

2

INTRODUCTION

Dear Customer,

Thank you for purchasing this compressor which has passed through our extensive quality assurance processes.

Every care has been taken to ensure that it reaches you in perfect condition. However, in the unlikely event that you should experience a problem, or if you require any assistance, please do not hesitate to contact us;

If you have a problem, call customer service do not return this compressor to the place of purchase.

CUSTOMER SERVICE

Australia: 1300 660 457

New Zealand: 0800 474 876

Operating times: Monday – Friday

8.00am - 5.00 pm

Australian Eastern Standard Time (AEST)

EXPRESS WARRANTY

STATEMENT - COMPRESSOR

You are not required to do anything to register your compressor purchase. Please attach the purchase receipt to this manual and ensure both are kept safe. We hope you enjoy your new compressor, and if you have any problems call customer service on the above phone numbers. Do not return to place of purchase.

Smart Marketing Group Pty Ltd (SMG) warrants that this compressor will be free from manufacturing faults or defects for 24 months from the date of purchase, providing original purchase receipt is kept and shown when needed and is subject to the terms and conditions below.

If a warranty fault appears within the warranty period,

SMG reserves the right to replace or repair the product.

In the event that SMG chooses to replace the product, this original warranty will expire at the original date.

If the product includes various accessories or components, only the defective accessory or component will be replaced or repaired.

SMG reserves the right to replace defective parts of the product with parts and components of similar quality, grade and composition where an identical part or component is not available.

Products presented for repair may be replaced by refurbished products of the same type rather than being repaired. Refurbished parts may be used to repair the products.

What is covered.

• Manufacturing fault or defect.

How to claim under this warranty.

• Call customer service.

• Ensure you have the following: Original purchase receipt, Model of compressor, Serial number of compressor.

• Discuss the issue.

• Customer service will advise which authorised service agent to take the compressor to provided the issue is a warranty one.

• Take compressor to authorised service agent for repair.

What is not covered.

• Commercial use of compressor.

• Use of compressor for hire

• Use of compressor in a commercial premises.

• Damage or deterioration due to transport.

• Damage caused by negligence, misuse, abuse or accident or incorrect voltage and wattage.

• Any corrosion or rusting.

• Damage caused by incorrect set up and start up.

• Replacement parts due to general wear and tear.

• Compressors with serial number defacement, modification or removal.

• Compressors which have been serviced by other than an authorised SMG service agent.

• Compressors with no original purchase receipt.

• Compressors which have been on sold, not original purchaser.

• Damage due non-servicing of compressor as is required by this manual.

• Blockages / damage caused by dust, dirt, spiders webs or insects.

• Damage caused by the incorrect fitting of accessories.

• Damage caused by overloading, overworking the compressor.

• Damage to attached equipment or third party accessories.

• Damage caused by attached equipment or third party accessories.

CONTACT DETAILS

Smart Marketing Group Pty Ltd

33-35 Lionel Road, Mt. Waverley

Victoria 3149, Australia.

Tel (+613) 9543 7266

Fax (+613) 9543 9839 [email protected]

3

COMPLETE WARRANTY STATEMENT – COMPRESSOR

As soon as you have purchased the compressor, we recommend that you check to make sure it is intact and that you read the operating instructions carefully before using it. The purchase receipt for this product is to be retained and must be presented if making a claim under the terms of the Smart Marketing Group (SMG) warranty.

Bank account statements are not acceptable for proof of purchase.

This warranty does not cover compressors intended for hire or use in commercial applications or in commercial premises. The warranty will under no circumstances extend to reimbursement or payment of damages, whether direct, indirect or consequential. The warranty is void if there is evidence the compressor has been modified or tampered with in any way or used with unauthorised accessories without our consent.

SMG declines any responsibility or liability whatsoever arising from misuse or abuse, negligent handling of the compressor or if the product has not been installed or failure to comply with the relevant safety, operating, setting and maintenance instructions (see further in this manual).

The warranty does not extend to installation or disconnection costs.

Any item sent freight forward/collect for repair will be refused. Warranty repairs are free of charge, provided the appliance is delivered to our service department or authorised service agent. The compressor will need to be returned, adequately protected in a box. SMG will not be responsible for any in-transit loss or damage. Assistance under the warranty will only be made available if the request is made to our customer service team on the contact numbers listed below and proof of purchase is provided.

This is a repair only warranty you will need to take the compressor to the authorised service agent after contacting our customer service centre.

If the product includes various accessories or components, only the defective accessory or component will be replaced or repaired.

SMG reserves the right to replace defective parts of the product with parts and components of similar quality, grade and composition where an identical part or component is not available.

Products presented for repair may be replaced by refurbished products of the same type rather than being repaired. Refurbished parts may be used to repair the products.

Damage caused by third party accessories is not covered under this warranty.

Damage caused to attached equipment or third party accessories will not be covered under this warranty.

Rust and corrosion are not covered under this warranty.

If a warranty fault is found, the freight cost will be credited to the owner. If no fault is found, the product will be returned and any costs associated with the service will be charged to the owner.

Blockages caused by spider webs, insects, dirt or accumulated dust are not covered by warranty. SMG reserves the right to replace or repair the appliance within the warranty period. Parts found to be defective due to a manufacturing default will be replaced free of charge.

In the event of SMG choosing to replace the appliance, the warranty will expire at the original date of purchase. If no warranty fault is found the owner will be advised and the product will be returned and any costs associated with the service will be charged to the owner.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits of this warranty are in addition to any rights and remedies imposed by Australian State and Federal legislation that cannot be excluded.

In New Zealand, this SMG warranty is in addition to the conditions and guarantees which are mandatory as implied by the New Zealand Consumer Guarantee Act 1993.

CONTACT DETAILS

Smart Marketing Group Pty Ltd

33-35 Lionel Road, Mt. Waverley

Victoria 3149, Australia.

Tel (+613) 9543 7266

Fax (+613) 9543 9839 [email protected]

4 5

4

LUBRICATION OF COMPRESSOR

This compressor is OIL FREE. Therefore there is NO oil used for lubrication.

ASSEMBLY

This compressor MUST be fully assembled by you prior to use. Failure to do so will result in the warranty being VOID.

Failure to fully assemble this compressor may also result in personal injury.

WORK ENVIRONMENT

Do not expose your air compressor to rain or use in damp or wet conditions. Keep the work area well lit. Always ensure your compressor is level and stable. Using your compressor on unlevel or unstable ground may cause it to tip over, this damage will not be covered under warranty.

Do not use your air compressor in the same area that you are spray painting or sanding. Always use your compressor in clean air. If needed use a longer air hose to reach your work area.

SAFETY

Before attempting to operate this air compressor the following basic safety precautions should be taken to reduce the risk of fire, electric shock and personal injury.

It is important to read the instruction manual and to understand applications, limitations and potential hazards associated with the air compressor. This air compressor is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

GUARD AGAINST ELECTRIC SHOCK

Avoid body contact with earthed or grounded surfaces

(e.g. pipes and refrigerators).

BEWARE OF CHILDREN AND PETS

Children and pets should be kept out of the work area.

Children should not be allowed to touch or operate the air compressor, tools or extension cords. This air compressor is not designed for use by young children or infirm persons without supervision. The air compressor and tools should be kept out of reach of children, preferably stored or locked in a secure cabinet or room when not in use.

USE THE RIGHT TOOL

Select the right tool for the job. Do not use a tool for a job for which it was not designed. Do not force a small air compressor to do the job of a heavy–duty air compressor.

Do not use the air compressor for purposes not intended.

WORK AREA

Work areas and benches should be kept tidy. Cluttered benches and work areas can cause accidents. Floors should be kept clean and free from rubbish. Special care should be taken when the floor is slippery due to sawdust or wax. Always leave sufficient distance, at least 5 metres between the air compressor and the work area, especially when using tools designed for sanding or spraying liquids.

If needed use a longer air hose to reach your work area.

DO NOT OVERLOAD AIR COMPRESSORS

The air compressor will do a better, safer job and give you much better service if it’s used at the duty cycle for which it was designed. The duty cycle will only take effect after the initial (1st ) tank fill for the day. This air compressor’s duty cycle is 75%. Duty cycle is the proportion of time during which the air compressor is operated. This means after 45 seconds of operation, motor pumping, the air compressor must be left for 15 seconds resting, motor not pumping.

When the motor is pumping the attached air tool can not be used. Only use the attached air tool while the compressor is not pumping. Stop using the attached tool as soon as the air compressor starts pumping.

5

DO NOT ABUSE

THE POWER CORD

Never yank or pull on the power cord to disconnect it from the mains supply socket. Never carry or pull your air compressor by its power cord. Keep the power cord away from heat, oil, solvents and sharp edges. If the power cord becomes damaged have it replaced by an authorised service facility.

EXTENSION CORDS AND REELS

This air compressor MUST be plugged directly into a 240V

AC wall socket.

This air compressor is NOT designed to be run off an extension cord/lead. If you need extra distance do NOT use an extension cord, USE A LONGER AIR HOSE.

The use of extension cords may cause power voltage loss and will result in damage to the motor. This will NOT be covered under warranty.

SECURE THE WORK PIECE

Whenever possible secure the work piece using clamps or a vice. It is safer than using your hands or feet and leaves both hands free to control the tool.

HOT COMPONENTS

Beware many of the components will get hot during use.

Never touch any of the metal pipes, pump or motor as these may burn.

DISCONNECT AIR COMPRESSOR

Ensure that the air compressor is disconnected from the mains supply when not in use, before servicing, cleaning, making adjustments or when changing any accessories.

REMOVE ADJUSTING KEYS

AND WRENCHES

Form the habit of always checking to see that any adjusting keys or wrenches have been removed from the air compressor before operating.

AVOID UNINTENTIONAL STARTING

Ensure that the switch is in the ‘OFF’ position before plugging the air compressor into the mains supply.

PROTECT FURNISHINGS

If using the air compressor inside your house, protect furnishings and floors with a suitable dust sheet.

FIRE PRECAUTIONS

When using the air compressor inside your house or workshop general fire precautions should be observed. As a precaution it is recommended that an expert is consulted on obtaining and using a suitable fire extinguisher.

MAINTAIN YOUR AIR

COMPRESSOR WITH CARE

Follow the instructions for cleaning and changing accessories. Check the air compressor power cord periodically and if damaged have it replaced by an authorised service facility. Keep handles clean, dry and free from oil and grease. Ensure that ventilation slots are kept clean and free from dust at all times. Blocked ventilation slots can cause overheating and damage to the motor.

CLEANING YOUR AIR COMPRESSOR

Always disconnect your air compressor from the mains power supply before you commence cleaning. Always ensure that your air compressor has cooled, about one (1) hour, before cleaning and storing. When cleaning your air compressor use only a damp soft cloth. NEVER use liquid or solvents of any type.

6 7

6

CHECK DAMAGED PARTS

Before using the air compressor it should be carefully checked to determine that it will operate properly and perform its intended function.

Check for the correct alignment of moving parts ensuring that they do not bind. Check for broken or missing parts and have them replaced or repaired at an authorised service facility. Check any other condition that may affect the operation of the air compressor. A guard or any other part of the air compressor that is damaged should be properly repaired or replaced by an authorised service facility unless otherwise indicated in this instruction manual.

Any switch that does not operate correctly must be replaced by an authorised service facility.

DO NOT use the air compressor if the ‘ON / OFF’ switch does not turn the air compressor ‘ON’ and ‘OFF’.

DO NOT use the power point switch to operate the air compressor as this will cause damage and injury may occur.

Any damage will not be covered under warranty.

PERSONAL SAFETY

Clothing

Do not wear loose clothing, jewellery or anything that could get caught in moving machinery.

Hair

Long hair should be tied back or contained in a protective covering.

Eye Protection

The use of safety goggles is highly recommended

(normal glasses are not sufficient for eye protection) when using an air compressor. Prescription glasses do not have safety lenses.

Footwear

Where there is the risk of heavy objects or if there is a risk of slipping on wet or slippery floors, suitable non–slip safety footwear should be worn. Protect your feet from dropping accidents.

Ear Protection

The use of ear protection is highly recommended when using air compressors. The continual noise may damage your ears.

Respiratory Protection

When operating any machinery that creates dust or when spray painting, an approved dust / filter mask must be worn. When machining concrete, man made fibres, especially MDF (Medium Density Fibre board), the resin used in these materials can be hazardous to your health.

Use an approved face mask with replaceable filter.

Do Not Over Reach

Do not over reach. Keep a proper footing and maintain your balance at all times. Avoid using abnormal stances and awkward body positions.

Stay Alert

Watch what you are doing, use common sense and never operate an air compressor when you are tired, drinking alcohol, taking drugs or if taking medication that causes drowsiness.

WARNING

Only use compressor when fully assembled

Do not attempt to modify the air compressor in any way; this will VOID your warranty.

The use of any attachment or accessory other than those recommended in this instruction manual could result in damage to the air compressor and could cause injuries to the operator.

This electric air compressor complies with Australian / New Zealand and International standards and safety requirements. Repairs should only be carried out by qualified persons using original spare parts. Failure to do so may result in considerable danger to the operator.

7

IMPORTANT

ELECTRICAL DATA

This air compressor is fitted with a sealed electrical connection plug that is compatible with the mains power supply for Australia / New Zealand and meets the requirements of international standards. This air compressor must be connected to a supply voltage that is equal to that stated on the rating label. If the mains power connection plug or power cord becomes damaged it must be replaced with a complete assembly that is identical to the original, and this must be replaced by an authorised service centre. Always follow the Australian / New Zealand requirements for connection to the mains supply. If in doubt always consult a qualified electrician.

SPECIFIC SAFETY INSTRUCTIONS

Warning!

Do not use the air compressor in areas where there is a risk of explosion or fire from combustible materials. The sparks generated from certain tools attached to air compressor can ignite combustible materials as well as flammable liquids, paint, varnish, petrol, flammable gases and dust of an explosive nature.

As a precaution it is recommended that you consult an expert on a suitable fire extinguisher and its use.

• Do not attempt to modify the air compressor, guards or the supplied accessories in any way.

• Domestic air compressors are designed for intermittent operation. Ideally a 75% duty cycle. (Meaning: 45 seconds ON motor pumping and 15 seconds OFF, motor not pumping). When the motor is pumping the attached air tool can not be used. Only use the attached air tool while the compressor is not pumping.

• Stop using the attached tool as soon as the air compressor starts pumping.

• Fully assemble compressor before use.

• Always ensure your compressor is level and stable.

Using your compressor on unlevel or unstable ground may cause it to tip over, this damage will not be covered under warranty.

• Never run this compressor without the wheels and rubber stopper being correctly fitted.

• Never use an extension cord with this compressor always use a longer air hose.

• Never connect to a generator which does not produce sufficient power, at least 3000W and has pure sine wave power output.

• Domestic air compressors are not designed for industrial / commercial applications.

• Domestic air compressors are not designed for continuous running. Always follow duty cycle - 75%.

• Avoid touching the pump area as it can become very hot and may burn.

• Ensure that the air compressor is disconnected from the mains supply when not in use, before servicing, lubricating, making changes and when changing attachments such as air hoses / tools.

• Always use the correct type of tool for the operation to be carried out.

• Never use the air compressor if any part of the unit is damaged. Always have the air compressor serviced by an authorised service agent.

• Always wear safety eye, ear and respiratory protection when operating the air compressor.

• Allow the tank to completely fill before using the air compressor.

• If the air compressor makes an unfamiliar sound or vibrates excessively, switch the air compressor ‘OFF’ immediately and disconnect from the mains power supply. Investigate the possible cause or consult your authorised service facility.

• Always move the air compressor using the handle and wheels.

• Always use the air compressor on stable ground.

• This air compressor is designed to compress normal air.

Never use to compress any other type (s) of gases.

• Never direct the jet of air or other liquids / gases towards your body, other persons or animals.

• Never direct the jet of air or other liquids / gases towards this air compressor.

• This air compressor is not suitable for pharmaceutical, food or sanitary purposes.

• This air compressor is not to be used to for filling scuba or oxygen air bottles or tanks.

• Always follow the instructions relating to the tools attached to this air compressor

8 9

8

1

2

3

4 5

COMPONENTS AND CONTROLS

1. Rear handle

2. Tank

3. Wheels

4. Tank drain tap

5. Rubber stopper

6. Safety Valve

7. Tank pressure gauge

8. Front handle

9. Pressure switch

10. On / Off button – red colour

11. Outlet pressure gauge

12. Air outlet - nitto style socket

13. Outlet pressure regulator

14. Water filter

15. Air filter

10

9

7

8

6

9

6

7

15

13

12

11

14

9

OPERATING INSTRUCTIONS

Unpacking

Carefully unpack your air compressor. This air compressor is bulky and heavy, two (2) person lift required.

Dispose of all packing material in an environmentally responsible manner.

Assembly

Your air compressor requires minor assembly before initial operation. Check that you have all required components required for assembly and initial use.

RUBBER STOPPER

To attach the rubber stopper to the bracket located on the bottom of the tank;

1. Undo the nut and remove the washer.

2. Push through the bracket and replace the washer.

3. Tighten the nut, Pic. 1

PIC. 1

WHEELS

1. Insert a bolt through the wheel.

2. Push through the tank wheel bracket.

3. Tighten the nut, Pic. 2

PIC. 2

WARNING

Do not attempt to operate this compressor until it is fully assembled.

Damage caused due to incomplete assembly will not be covered under warranty.

Ensure the air compressor is disconnected from the power supply before carrying out any assembly, maintenance or adjustments on the machine

10 11

10

HANDLE

1. Loosen bolts in tubes welded to the tank.

2. Push handle into tubes welded on the tank.

3. Tighten the bolts to hold handle in place, Pic. 3.

PIC. 3

Tighten bolts to hold handle

Slide handle into tubes

AIR FILTER

The supplied air filter must be used.

Failure to do so may result in irreparable damage and will void the warranty, Pic. 4

To install;

1. Carefully screw supplied air filter into the threaded hole on the top of the pump head. This only needs to be done up by hand. Do not use tools to tighten air filter.

NOTE: Do not OVER TIGHTEN as this may damage the air filter or cylinder head which will NOT be covered under warranty.

PIC. 4

STARTING AND STOPPING YOUR AIR

COMPRESSOR

Pic. 5

NOTE: Always ensure that you plug your air compressor into a standard 240V AC power point. Never use an extension cord as this can lead to a voltage drop which may cause power loss and over heating. Use a longer air hose if you need to get closer to your work area.

Always start and stop the compressor using the ON/OFF switch on the Pressure Switch (Pic. 1 Item 9 and 10 as well as Pic. 5). Damage caused by not using this switch will not be covered by warranty.

To turn your air compressor ON;

Lift up the red ON / OFF switch on top of the pressure switch

To turn your air compressor OFF;

Push down the red ON / OFF switch on top of the pressure switch

11

PIC. 5

Lift switch up for on

Push switch down for off

USING THE AIR COMPRESSOR

Your compressor does not require running in. Before use ensure you have read and understood these instructions.

Before use ensure this compressor is fully assembled as per pages 10 and 11.

FILTER REGULATOR

Pic. 6

This air compressor comes with a filter regulator, which will filter some water and other particulates from the air as it passes through the regulator.

Before starting run through this simple list;

1. Fully assembled.

2. Drain tap – open and drain tank.

3. Drain tap – close fully.

4. Check power lead for any damage. If damaged have replaced by an authorised service centre.

5. Plug compressor into a standard 240V 10Amp AC power point and turn ON.

6. Lift the red button to turn ON, see page 11, Pic. 5.

7. Allow the compressor to fill the air tank.

8. Turn the compressor OFF.

9. Turn the power point OFF and disconnect the power lead from the power point.

10. Connect your air hose and air tools.

11. Reconnect to the power lead to the power point and turn ON.

12. Turn your compressor ON.

13. Once turned on and you begin using the connected air tools the compressor will start and stop without warning. This is controlled by the pressure switch.

These pressure settings are factory set and should not be changed.

To drain any fluid from the filer regulator;

1. Gently pull the nipple down.

2. Allow fluid to drain.

3. Allow nipple to seal.

To clean bowl (no tools required);

1. Unscrew the clear bowl.

2. Rinse the bowl in clear water.

3. Allow to air dry fully.

4. Screw the clear bowl back into place.

PIC. 6

Regulator

Air outlet

Water filter bowl

Pull down to drain/empty

IMPORTANT

Pumping starts at (minimum) 115PSI and stops at

(maximum) 145PSI. Once the initial pump up stage has finished you can use the compressor.

This compressor has a maximum pressure of 10 bar.

Always regulate the outlet air pressure to match your air tool.

Different air tools require different operating pressures. Always check with the air tool manufacturer if unsure.

12 13

12

PIC. 7

The configuration of tools and accessories can be varied to suit your particular requirements. A basic recommended set up is shown in Pic. 7.

When you have finished using your air compressor follow these simple steps;

1. Turn your air compressor OFF, using the ON/OFF switch.

2. Turn the power point OFF and disconnect the power lead.

3. Disconnect your air tools and air hose.

4. Clean your air hose and air tools.

5. Store your air hose and air tools in a secure well ventilated cabinet.

6. Slowly open the tank drain tap, see page 16.

This allows excess air and moisture, water, to vent.

7. Leave the tank drain tap open. This allows any moisture to drain while the air compressor is stored.

NOTE: Use of a water trap may be of benefit to ensure no water or moisture reaches your air tool.

IMPORTANT

Pumping starts at (minimum) 115PSI and stops at

(maximum) 145PSI. Once the initial pump up stage has finished you can use the compressor.

This compressor has a maximum pressure of 10 bar.

Always regulate the outlet air pressure to match your air tool.

Different air tools require different operating pressures. Always check with the air tool manufacturer if unsure.

13

Not supplied, purchased separately.

ADJUSTING THE PRESSURE

To adjust the outlet air pressure, use the red coloured regulator knob and check the pressure on the outlet pressure gauge, Pic. 8.

If the pressure needs to be lower, turn anti clockwise.

If the pressure needs to be higher, turn clockwise.

Use the gauge to ensure you set the correct working pressure.

Note: Different air tools require different operating pressures. Always check with the tool manufacturer if unsure.

SAFETY VALVE

Pic. 9

NOTE: When checking the safety valve ALWAYS wear safety glasses.

To check the operation of the safety valve the air tank will need to be full. Gently pull the ring outwards. This should release air under pressure. Release the ring and this should stop the air out flow immediately.

If the safety valve does NOT work in this manner,

STOP the air compressor immediately and have the air compressor checked / serviced by an authorised service centre.

PIC. 9

PIC. 8

Regulator

Air Outlet

Tank pressure gauge

Outlet

Pressure

Gauge

Pull to check operation

IMPORTANT

This compressor has a maximum pressure of 145PSI

(10 bar). Always regulate the outlet air pressure to match your air tool.

Different air tools require different operating pressures. Always check with the air tool manufacturer if unsure.

14 15

14

AIR FITTING

Pic. 10

This air compressor is fitted with a ‘Nitto style’

(female) socket.

1. Push in the ‘Nitto style’ male plug (not included).

2. Fully and completely push the ‘Nitto style’ male plug

(not included) into the ‘Nitto style’ female socket until

it clicks and the collar locates forward.

To remove

1. Push collar down and remove male fitting,

collar will stay retracted.

NOTE: For ease of connection and disconnection use regulator to reduce outlet pressure to 0PSI.

This compressor has a maximum pressure of 145PSI

(10 bar).

Always regulate the outlet air pressure to match your air tool.

Different air tools require different operating pressures.

Always check with the air tool manufacturer if unsure.

PIC. 10

Tank pressure gauge

Outlet pressure gauge

Nitto style outlet socket

(Air Outlet)

DRAIN TAP

Pic. 11

After use open the drain tap to drain excess air and any moisture. The excess air will also help purge the moisture.

Leave the drain tap open when air compressor is not in use, so any moisture can continue to drain

To open the drain tap pull the lever down to vertical.

To seal the drain tap push the lever up to horizontal.

NOTE: Remember to seal the drain tap before starting the compressor.

PIC. 11

Drain Tap Sealed

OR

To close and seal push lever up Right or left

Drain tap opened un-sealed

15

MAINTENANCE

Daily: Before use

1. Seal the tank drain tap,see page 15, Pic. 11.

2. Check safety valve operation,see page 14, Pic. 9.

After Use

1. Open the tank drain tap,see page 15, Pic. 11. and leave open to allow to drain

2. Wipe down the compressor.

3. Store safely and securely

TROUBLE SHOOTING

If your compressor does not start

• Check that you have plugged the power lead into a standard 240V 10Amp power point and turned the switch ON.

• Check that you have turned the air compressor ON/OFF switch ON.

• The air tank may be full. Use your air tool and the air compressor should start when the pressure decreases to 115PSI.

If these tips do not work please have your unit checked by an authorised service centre.

Call Smart Marketing Group for your closest centre,

Australia. 1300 660 457 N.Z. 0800 474 876.

16 17

PARTS DIAGRAM

16

10

11

8

9

3

4

Part

1

7

Description

Air Filter

Exhaust Elbow

Exhaust Tube Set

Wheel Set

One Way Valve

Drain Tap

Cushion Foot Set

Unloading Tube Set

1

1

1

1

1

1

Qty

1

2

SMG Part No.

95 BRC95AF

95 BRC95EE

95 STDDSMET

95 STSMWH

95 BRC95OWV

95 BRC95DT

95 BRC95RS

95 STDDUT

18

19

20

15

16

Part

14

17

Description

Filter Regulator

Outlet Nitto Style Socket (Female) 1

Safety Valve 1

Pressure Switch (10 Bar)

Qty

1

1

Pressure Gauge Outlet

Pressure Gauge Tank

Handle

1

1

1

SMG Part No.

95 STREGWT

95 STNSF

95 ST10SPV

95 ST10PS

95 STOPG

95 STTPG

95 STDDH

17

TECHNICAL INFORMATION

Specifications

Inflator

Voltage

Motor

Wattage

No Load Speed

Free Air Delivery (FAD)

Tank Size

Duty Cycle

Max. Tank Pressure

Outlet Pressure

Minimum Generator Size

Noise Rating

Motor/Pump

Pressure Cycle

Number of Outlets

SXAC1521121

240V AC ~ 50Hz

Electric 1.5 HP

1100W

2850 RPM

85L per minute

21L

75%

145PSI (10 Bar)

1PSI - 145 PSI Adjustable

Pure Sine Wave 3000W

80dB@5m

Kicks in 115PSI

Stops 145PSI

1

*

For any queries or assistance call

Customer Service

AUST. 1300 660 457

NZ 0800 474 876

Hours of operation:

Monday to Friday 8.00am - 5.00pm AEST

Do not return to place of purchase.

Keep your purchase receipt, this will be required to make any claims under the 24 month warranty.

STANLEY®, The STANLEY Logo, The Notched Rectangle and the Yellow and Black Diagonal Package

Design are all trademarks of the Stanley Black & Decker, Inc or an affiliate thereof and are used under license. Product manufactured and distributed by Smart Marketing Group Pty Ltd.

Manufactured in China.

18