Clarke 3110876 Operating & Maintenance Instructions
Clarke 3110876 provides ample torque and speed for a wide variety of applications. Its ½” square drive allows for easy socket changes and compatibility with various impact sockets. The forward and reverse button enables effortless direction control, while the speed control feature offers precise power adjustment. Additionally, the ¼” female inlet adaptor ensures compatibility with standard air hoses. Furthermore, the included oil port allows for easy lubrication, extending the tool's life.
Advertisement
Advertisement
43-PC AIR TOOL KIT
MODEL NO: CAT120
PART NO: 3110876
OPERATING & MAINTENANCE
INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC0420 - ISS 2
INTRODUCTION
Thank you for purchasing this CLARKE Air Tool Kit.
Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
Please keep these instructions in a safe place for future reference.
INVENTORY
When opening the case for the first time, check that all the items are present.
Any damage or deficiency should be reported to your CLARKE dealer immediately. Your CAT120 Air Tool Kit should include the following:
AIR TOOLS IN THE KIT
1 x ½” Square Drive Impact Wrench
1 x Air Hammer
1 x Reversible Drill
1 x
¼ ” Die Grinder
1 x Dual Acting Sander
GENERAL ACCESSORIES
1 x Air Inlet Adaptor ( ¼ ” male)
1 x Oil Bottle
1 x Hex Key 4mm
FOR THE DRILL
1 x Chuck key
4 x 6.35 mm Hex shank screwdriver bits:
Sizes: 4 & 6 mm straight; Phillips Nos. 2 & 3
FOR THE DIE GRINDER
5 x Assorted grinding stones - 6 mm shank
5 x Assorted grinding stones - 3 mm shank
1 x Pair of spanners
2
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
FOR THE CHIPPING HAMMER
4 x Chisels with various profiles (10.2 mm locating shank - 125 mm length)
FOR THE DUAL ACTION SANDER
1 x 150 mm Backing Pad (accepts 150 mm self-adhesive sanding discs)
FOR THE IMPACT WRENCH
10 x impact sockets, ½” Square drive sizes: 9,10,11,13,14,17,19,22,24,27 mm
TECHNICAL SPECIFICATIONS
The 5 x air tools supplied in this CAT120 kit have a 1/4” BSP female threaded connection for use with an maximum air supply pressure of 90 psi (6.2 bar).
IMPACT WRENCH
Air Consumption
Drive size
Max No Load Speed
Max Torque
8 cfm
1/2” square
7000 rpm @ 90psi
230 ft/lb
Sound Pressure Level (LpA dB)
Sound Power Level (LwA dB)
84.4 dB(A)
95.4 dB(A)
Vibration Levels
2.6 m/s
2
(uncertainty factor K= 0.72m/s
2
)
Dimensions (L x W x H) & Weight 220 x 75 x 180 mm Weight 2.2 kg
HAMMER/CHISEL
Air Consumption 3-16 cfm (84-452 l/min)
Max Blows per minute
Vibration Levels
4500
14.6 m/s
2
(uncertainty factor (K= 0.99m/s
2
)
84 dB LpA Sound pressure level
Sound power level 95 dB LWA
Dimensions (L x W x H) & Weight 153 x 48 x 152 mm Weight = 1.1 kg
3
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
REVERSIBLE DRILL
Chuck Size
Air Consumption
Max Speed
Sound Pressure Level (LpA dB)
1.5 - 10 mm
6 cfm
1800 rpm
87 dB(A)
Sound Power Level (LwA dB)
Vibration Levels
98 dB(A)
1.2 m/s
2
(K= 1.25 m/s
2 )
Dimensions (L x W x H) & Weight 191 x 42 x 144 mm Weight 1.15 kg
DIE GRINDER
Air Consumption
Max Speed
Sound Pressure Level (LpA dB)
Sound Power Level (LwA dB)
4 cfm (1151 l/min)
22000 rpm
83.5 dB(A)
94.5 dB(A)
Vibration Levels
1.2 m/s
2
(K=0.35 m/s
2
)
Dimensions (L x W x H) & Weight 173 x 46 x 68 mm Weight 0.64 kg
DUAL-ACTING SANDER
Air Consumption @ 6.3 bar
Pad size
Sound Power Level
Sound Pressure Level
Vibration Level
2-16 cfm (56-452 l/min)
150 mm
98.2 dB LWA
87.2 dBA
Uncertainty Factor (K)
2.5 m/s
2
1.25 m/s
2
Dimensions (L x D x H) & Weight 223 x 73 x 123 mm Weight = 1.81 kg
Max Speed 10,000 rpm
4
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
GENERAL SAFETY WARNINGS
CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN
PERSONAL INJURY AND/OR DAMAGE TO PROPERTY.
WORK ENVIRONMENT
1. ALWAYS keep the work area clean and tidy.
2. ALWAYS dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of the way.
3. ALWAYS keep children & visitors away - Do not let children handle the tools.
4. DO NOT operate the tool where there are flammable liquids or gases.
USE OF AIR POWERED TOOLS
1. ALWAYS stay alert and use common sense - do not operate air tools when you are tired or under the influence of alcohol, drugs or medication.
2. ALWAYS wear eye protectors when using the tool - Eye protection must provide protection from flying particles/objects from the front and the side.
Ear protectors should also be worn.
3. DO NOT overreach - Keep proper footing and balance at all times.
4. DO NOT use any type of bottled gas as a source of power for this tool.
5. DO NOT connect the air supply hose with your finger on the trigger.
6. DO NOT exceed the maximum pressure for the air tools 90 psi / 6.2 bar.
7. ALWAYS check hoses for leaks and ensure that all connections are secure.
8. ALWAYS keep the air supply hose away from heat, oil and sharp edges.
9. DO NOT use the tools for any purpose than that described in this manual.
10. DO NOT fit the tools to any stand or clamping device that may damage it.
11. ALWAYS disconnect from the air supply when:
• Performing maintenance
• The tools are not in use.
• The tools will be left unattended.
• Moving to another work area.
12. DO NOT use any tool if it is defective or operating abnormally.
5
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
13. ALWAYS avoid damaging the tools by applying excessive force.
14. ALWAYS maintain the tools. Keep them clean for the safest performance.
15. Quick change couplings should not be located at the tool. They add weight and could fail due to vibration.
16. DO NOT force or misuse the tools which will do a better and safer job at the rate for which they are designed.
17. These tools vibrates with use. Vibration may be harmful to your hands or arms. Stop using the tool if discomfort, a tingling feeling or pain occurs.
Seek medical advice before resuming use.
IMPACT WRENCH SPECIFIC HAZARDS
1. ALWAYS use the impact wrench as described in these instructions.
2. ALWAYS ensure the wrench is not moving and disconnected from the air supply when changing sockets etc. Use only impact wrench sockets....DO
NOT use standard sockets.
3. ALWAYS finish tightening nuts with a torque wrench or suitable spanner to the correct torque as recommended by the vehicle manufacturer.
4. ALWAYS avoid excessive use of the impact wrench. When tightening a nut or bolt, only allow the wrench to impact briefly to avoid overtightening.
5. ALWAYS ensure that the socket is correctly installed before switching on.
6. ALWAYS wear suitable respiratory protection due to the possible presence of asbestos dust from vehicle brake linings.
7. ALWAYS disconnect from the air supply when changing sockets or when the wrench is not required for immediate use to avoid accidental starting
8. DO NOT carry the wrench by the air supply hose.
9. ALWAYS use both hands to control the wrench.
10. ALWAYS ensure the wrench has stopped before putting it down.
AIR HAMMER SPECIFIC HAZARDS
1. Only use accessories designed for use with this tool.
2. DO NOT use any of the chisels supplied as a hand struck tool.
3. DO NOT use blunt chisels which require excessive pressure and can break from fatigue. Always use sharp tools.
4. DO NOT mis-use the tool by prising which can result in a broken chisel.
5. ALWAYS ensure there are no hidden electrical cables, gas pipes etc, which could cause a hazard if damaged by action of the chisels.
6
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPRESSED AIR REQUIREMENTS
WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF
COMPRESSORS AND COMPRESSED AIR SYSTEMS.
A typical air line layout is shown below. If an automatic in-line filter/regulator is used, it will keep the tool in good condition, but should be regularly checked
& topped up with oil. CLARKE air-line oil should be used and the lubricator adjusted to approx 2 drops per minute.
Use only clean, dry, regulated compressed air as a power source.
Air compressors used with the tool must comply with the appropriate
European Community Safety Directives.
7
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
A build-up of moisture or oil in the air compressor will accelerate wear and corrosion in the tool. ensure any moisture is drained from the compressor daily and the inlet filter is kept clean.
If an unusually long air hose is required, (over 8 metres), the line pressure or the hose inside diameter may need to be increased.
The air hose must be rated at least 150% of the maximum operating pressure of the air tool.
Never exceed the maximum operating pressure for the air tool. It is recommended that air pressure to this tools does not exceed 90 psi at the tool when running. Higher pressures and unclean air will shorten the life of an air tool due to faster wear and is a possible safety hazard.
CONNECTING THE TOOLS TO THE AIR LINE
1. Remove the plastic blanking plug from the air inlet connection.
2. Pour 2-3 drops of CLARKE airline oil into the oil filling port. This should be done regardless of whether or not a lubricated air supply is to be used.
3. If required, connect an in-line mini oiler to the tool to prolong the life of any air tool.
4. Connect a suitable hose as shown or use the connector supplied to connect directly to the hose.
• PTFE tape may be useful for sealing threaded connections
5. Connect the other end of the hose to the compressor.
6. Turn on the air supply and check for air leaks. Rectify any found before proceeding.
7. If using a mini oiler, place a sheet of paper next the exhaust port and hold the throttle open for approximately 30 seconds. The oil volume is correctly set when a light stain of oil can be seen on the paper. Excessive oil should be avoided.
Your air tool is now ready for use.
8
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
THE IMPACT WRENCH
1 1/2” Square Drive
2 Forward/reverse button
3 Trigger
4 Speed Control
5 ¼ ” female inlet adaptor
6 Handle
7 Oil port
FITTING THE IMPACT SOCKET
WARNING: NEVER USE STANDARD SOCKETS. THESE MAY SHATTER WITH
SERIOUS CONSEQUENCES. ONLY USE IMPACT SOCKETS DESIGNED FOR
USE WITH IMPACT TOOLS.
1. Select the impact socket you require, which must be in good condition and fit the tool exactly.
2. Push the socket onto the square drive shaft as shown.
9
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
ADJUSTING THE DIRECTION AND SPEED
WARNING: WAIT UNTIL THE WRENCH HAS STOPPED ROTATING BEFORE
OPERATING THE FORWARD/REVERSE SWITCH.
THE FORWARD/REVERSE BUTTON SHOULD BE USED AS FOLLOWS:
1. For normal tightening, the impact wrench should be operated in the forward (F) direction.
2. For loosening, the he impact wrench should be operated in the reverse (R) direction.
NOTE: Where the torque setting is critical, the final tightening of nuts or bolts, must be by hand using a correctly calibrated torque wrench.
ADJUSTING THE POWER
To adjust the power, set the air regulator to one of the 4 settings available.
1 (Low) - 4 (High)
USING THE IMPACT WRENCH
WARNING: NEVER USE STANDARD SOCKETS. THESE MAY SHATTER WITH
SERIOUS CONSEQUENCES. ONLY USE IMPACT SOCKETS DESIGNED FOR
USE WITH IMPACT TOOLS.
LOOSENING A WHEEL NUT/BOLT
1. Remove any wheel trim, before selecting the appropriate socket and placing firmly on the square drive of the wrench.
10
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
2. With the FORWARD/REVERSE switch in the REVERSE running position, and holding the wrench firmly in BOTH HANDS, pull the trigger. The nut/bolt will be impacted repeatedly until it is loosened.
IMPORTANT: Release the trigger as soon as the nut begins to loosen.
3. Jack up the vehicle according to the vehicles handbook so that the wheel is clear of the ground, then proceed to fully undo the wheel nuts/bolts.
4. Soak rusted nuts/bolts in penetrating oil, and break rust seal before twisting off with the wrench.
WARNING: ENSURE THAT THE CORRECT SOCKET IS BEING USED FOR THE
NUTS/BOLTS ON YOUR PARTICULAR VEHICLE. AN INCORRECT SOCKET
SIZE IS LIKELY TO DAMAGE THE HEADS OF THE BOLTS/NUTS.
TIGHTENING A NUT/BOLT
1. Start the nut by hand, ensuring it is not cross threaded, then with the appropriate socket installed on the wrench, place it on the nut/bolt.
2. With the FORWARD/REVERSE selector in the clockwise (FORWARD) running position and holding the wrench firmly in BOTH HANDS, pull the trigger.
3. Run each nut/bolt up in turn until it is ‘nipped’ up only - do not tighten.
When all nuts are nipped up, tighten progressively by pulling the trigger fully and allowing the action to operate briefly to prevent overtightening.
4. ALWAYS finish tightening with a torque wrench. The weight of the vehicle will need to be placed on the wheel to prevent it from rotating while the nuts are tightened. Ensure the final torque applied to the nuts/bolts meets the vehicle manufacturer’s recommendations.
DISCONNECTING THE AIR SUPPLY
1. Do not disconnect the hose until the supply is isolated at a shut-off valve.
2. Once the pressure has been isolated, disconnect the air supply hose.
3. Shut down the compressor at the end of the session.
11
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
THE HAMMER/CHISEL
1 Outboard lug
2 Retaining spring
3 Inboard lug Air Inlet
4 Trigger
5 ¼ ” female inlet adaptor
6 Speed controller
7 Chisels (flat & pointed)
FITTING THE CHISEL
1. Select which chisel is best suited to the task.
2. First remove the retaining spring from the nose by unscrewing it.
• Use the inboard lug to gain purchase.
3. Insert the chisel into the air hammer as shown.
4. Replace the retaining spring.
• Use the lugs to help tighten.
12
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
ADJUSTING THE FORCE
Chisel force may be adjusted by turning the regulator knob, located at the base of the handle.
• Turn anticlockwise to increase force.
• Turn clockwise to reduce the force.
USING THE CHIPPING HAMMER
1. Hold the tool firmly, then bring the tool towards the work at an angle of approximately 60-70 degrees.
2. Squeeze the trigger with the chisel in light contact with the work.
3. Move slowly across the work surface. To remove scale, rust or other contaminants, only a light force should be required.
4. Release the trigger to stop operation whilst maintaining contact with the work.
5. The tool may operate briefly after the trigger is released.
NOTE: The retaining spring has a life expectancy, depending upon the intensity of usage. It is recommended that you procure a spare spring for use in the event of failure occurring during the course of a particular job.
DISCONNECTING THE AIR SUPPLY
1. Do not disconnect the air hose until the supply is isolated at a shut-off valve.
2. Once the pressure has been isolated, disconnect the air supply hose.
3. Shut down the compressor at the end of the work session.
13
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
THE REVERSIBLE DRILL
NO DESCRIPTION
1 Chuck
2 Trigger
3 Direction control switch
INSERTING/REMOVING THE DRILL BIT
1. Open the chuck jaws by inserting the chuck key in one of the holes in the chuck and turning it as shown.
• Make sure that the head of the chuck key is located on the cog barrel of the chuck.
NO DESCRIPTION
4 Handle
5 ¼ ” female inlet adaptor
14
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
2. Open sufficiently to take the drill bit.
3. Place the drill bit in the jaws of the chuck as far as it will go.
4. Close the chuck jaws and tighten to grip the drill bit by turning the chuck key as shown.
5. Make sure that the chuck jaws are fully closed and that the drill bit is firmly held.
DIRECTION CONTROL SWITCH
WARNING: WAIT UNTIL THE CHUCK HAS STOPPED ROTATING BEFORE
OPERATING THE DIRECTION CONTROL SWITCH.
The direction control switch should be used as follows.
1. For normal drilling the drill must be operated in the forward (F) direction.
2. If the drill bit jams whilst drilling, release the trigger switch.
3. When the drill has come to a complete stop, move the direction control switch to the reverse (R) position.
USING THE REVERSIBLE DRILL
WARNING: MAKE SURE THAT THE CHUCK KEY HAS BEEN REMOVED
BEFORE USING THE DRILL.
1. Squeeze the trigger switch to start the air drill.
2. Wait until the air drill is running at its maximum speed before applying it carefully to the workpiece.
3. Release the trigger switch to stop the air drill.
DISCONNECTING THE AIR SUPPLY
1. Do not disconnect the hose until the supply is isolated at a shut-off valve.
2. Once the pressure has been isolated, disconnect the air supply hose.
3. Shut down the compressor at the end of the session.
15
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
THE DIE GRINDER
NO DESCRIPTION
1 Collet
2 Spindle
3 Trigger lock
INSTALLING THE COLLET
1. Select the grinding stone you require.
2. Two collets of different sizes are provided. Select whichever fits the shank of the stone you have chosen.
• The larger collet is already installed in the grinder.
NO DESCRIPTION
4 Trigger
5 ¼ ” female inlet adaptor
16
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
3. If another collet is to be used, undo the screw cap completely and pull out the collet from the collet seat. Replace it with the new collet and screw the cap loosely back on.
FITTING THE GRINDING STONE
IMPORTANT: Never use chipped or cracked grindstones.
1. Slip the shank of the chosen stone into the collet and tighten the screw cap finger tight.
2. Place the smaller of the two wrenches over the collet seat to stop the tool from rotating.
3. Use the larger wrench to fully tighten the collet and grip the stone in position as shown.
OPERATING THE DIE GRINDER
1. Slide the throttle locking lever forward while squeezing the trigger against the body of the tool.
2. Allow the tool to reach full working speed before presenting the grinding stone to the workpiece.
Do not use excess pressure on the grinding stone as this will shorten its life.
3. Release the trigger to stop the grinder.
• The tool will continue to rotate for a short time after the trigger has been released.
4. Always ensure the grinder has stopped before putting it down.
DISCONNECTING THE AIR SUPPLY
1. Do not disconnect the hose until the supply is isolated at a shut-off valve.
2. Once the pressure has been isolated, disconnect the air supply hose. Shut down the compressor at the end of the session.
17
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
THE DUAL ACTION SANDER
NO DESCRIPTION
1 Trigger
2 Speed control
3 Balancer
NO DESCRIPTION
4 Locking nut
5 Backing pad
6 ¼ ” female inlet adaptor
FITTING THE BACKING PAD
1. Turn spindle lock until the knurled portion contacts the flat surface on the spindle.
2. Thread the backing pad into the spindle, by grasping the balancer, with one hand and the pad with the other. Do not over tighten.
3. Now turn the spindle lock so that the knurled portion is away from the flat on the spindle, and the spindle turns freely.
18
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
4. DO NOT operate tool with spindle in locked mode as performance would be severely affected and a hazardous situation may result.
FITTING THE SANDING SHEET
1. Peel off the back of the self adhesive sanding sheet and stick it to the backing pad.
ADJUSTING THE SPEED
Adjust the operating speed if required, by twisting the speed control.
• Clockwise to increase the sanding speed.
• Anticlockwise to decrease the sanding speed.
USING THE SANDER
1. Place the sander on the workpiece and press down on the trigger to start the sander.
2. Release pressure from the trigger to stop the sander.
3. Always ensure the sander has stopped before putting it down on any surface after use.
4. Avoid contact with the moving sanding pad and wear suitable gloves to protect the hands.
5. Never start the sander unless the abrasive pad is applied to the workpiece.
6. Always wear a face mask when using the sander as protection from airborne particles of sanded material. Avoid disturbing existing dust and minimise the scattering of dust in the workplace environment. Take steps to control the dust at the point of emission.
DISCONNECTING THE AIR SUPPLY
1. Do not disconnect the hose until the supply is isolated at a shut-off valve.
2. Once the pressure has been isolated, disconnect the air supply hose.
3. Shut down the compressor at the end of the session.
19
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
MAINTENANCE
WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE
AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE.
DAILY
1. Before use, drain water from the airline filter and compressor.
2. If no line lubricator or mini oiler is used, ensure that oil is applied to the tool on a daily basis through the air inlet connection. Run a few drops of
CLARKE airline oil through the tool before use. It may be entered into the tool air inlet, (ensuring the strainer is clear), or into the hose at the nearest connection to the air supply.
3. This procedure should be repeated after every two to three hours of use, or at the start of the working day.
4. Check the air inlet screen filter for blockage and clean if necessary.
5. Keep the body of the tool clean and free from debris.
CLEANING & OVERHAUL
1. Grit or gum deposits in the tool may reduce efficiency.
2. After extensive use, remove the inlet screen filter and flush out the mechanism with gum solvent oil or an equal mixture of air-line oil and paraffin. Allow to dry before use.
3. If the tool still runs erratically or becomes inefficient, and the air supply is of good quality, it may be necessary to dismantle the air motor and replace worn or damaged parts. You may prefer to take the tool to your CLARKE dealer if internal maintenance is required.
4. The air tool may be dismantled by unfastening the bolts and removing the rear cover prior to replacing any worn or damaged parts.
5. While the impact wrench or air hammer is a dismantled state, it may be desirable to grease the hammer mechanism and applying a small amount of good quality bearing grease.
This may be better left to your CLARKE dealer.
20
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
TROUBLESHOOTING
SYMPTOM PROBLEM SOLUTION
Tool runs at normal speed but slows down under any load.
Tool runs slowly. Air flows weakly from exhaust.
Tool will not run. Air flows freely from exhaust.
1. Excessive pressure on
tool.
2. Motor parts worn.
3. Worn or sticking
mechanism due to
lack of lubricant.
1. Reduce the force
applied to the tool.
2. Return to CLARKE dealer
for repair.
3. Drip air tool lubricating
oil into air inlet. Allow oil
to soak moving parts
before using.
1. Motor parts jammed
with gum/dirt.
2. Regulator in closed
position.
3. General airflow
blocked by dirt.
1. Motor vanes stuck
due to buildup of
foreign material.
1. Examine inlet air filter for
cleanliness.
2. Adjust regulator to open
position.
3. Operate tool in short
bursts.
1. Disconnect air supply
and rotate tool assembly
manually.
2. Try operating tool in
short bursts.
3. Tap motor housing gently
with a rubber mallet.
4. Drip a few drops of air
tool lubricating oil into air
inlet to soak moving
parts.
Tool will not shut off.
1. O-rings damaged or
ill-fitting in seat.
1. Return to CLARKE dealer
for repair.
STORAGE
If the tool is to be stored or is idle for longer than 24 hours, run a few drops of air-line oil into the air inlet and depress the trigger in order to lubricate the internal parts.
When not in use, the tool should be disconnected from the air supply and stored in a dry place out of the reach of children. Avoid storing in a damp environment.
Avoid storing air tools where the temperature is below 0 o
C.
21
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
PERFORMANCE
Please note that outside factors may affect the operation and efficiency of the air tool.
These include reduced compressor output, excessive drain on the airline, moisture ingress, restrictions in the air-line such as the use of connectors of incorrect size or poor condition which will reduce the air supply.
Your air tool has been designed to give long & trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local CLARKE dealer.
ACCESSORIES
A wide range of accessories is available including filter/regulators, lubricators, high-pressure hoses (5 to 50 metres) etc.
Contact your CLARKE dealer for further information or CLARKE International
Service Department on 01992 565333.
CLARKE Air Line Oil (part no. 3050825) is available from your CLARKE dealer.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL RECYCLING POLICY
If disposing of broken tools or any damaged components, do not dispose of with general waste. This products contains valuable raw materials. Metal products should be taken to your local civic amenity site for recycling of metal products.
22
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
DECLARATION OF CONFORMITY
23
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - IMPACT WRENCH
24
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - IMPACT WRENCH
No Description
6
7
4
5
1
2
3
Protecting rubber
Housing
Bolt
Anvil bush
Anvil collar
O-ring
Anvil
8
9
Hammer pin
Hammer cage
10 Hammer dog
11 Drive Cam
12 Ball bearing
13 Oil seal
14 Front end plate
15 Rotor blade
16 Rotor
17 Pin
18 Cylinder
19 Bolt
20 Rear end plate
21 Gasket
22 Rear cover
23 Washer
No Description
24 Bolt
25 Protecting rubber
26 Valve sleeve
27 Reverse valve
28 O-ring
29 Valve stem
30 Washer
31 Steel ball
32 Inlet spring
33 Air inlet plug
34 Dust free cover
35 Spring
36 O-ring
37 Air regulator
38 Bolt
39 Pin
40 Trigger
41 Exhaust cover
42 Bolt
43 Screw
44 Spring
45 Pin
25
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - DIE GRINDER
26
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - DIE GRINDER
No Description
6
7
4
5
1
2
3
Housing
Valve stem seat
Trigger
Throttle trigger
Spring
Hinge pin
Hinge pin
8
9
O-ring
O-ring
10 Valve stem
11 Spring
12 Air regulator
13 O-ring
14 O-ring
15 Screw cap
16 Muffler cover
17 Air inlet plug
18 Bearing
19 End plate
No Description
20 Pin
21 Rotor
22 Rotor blade
23 Cylinder
24 Washer
25 Bushing
26 Front plate
27 Pin
28 Bearing
29 Collet seat
30 Locking ring
31 Front cap
32 Collet (small)
Collet (large)
33 Collet screw cap
34 Wrench (small)
Wrench (large)
35 Male connector
36 Grinders (set of 10)
27
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - AIR CHISEL
No Description
7
8
5
6
3
4
1
2
Housing
Rubber Gasket
O-Ring
Regulator
Control Pin
O-Ring
Ball Valve
Spring
9 Air Inlet Connector
10 Rear Valve
11 Valve Disc
12 Front Valve
13 Pin
No Description
14 Pin
15 Piston
16 Cylinder
17 Retainer Spring
18 Trigger
19 Roll Pin
20 Roll Pin
21 Piercing chisel
22
23
24
25
26
Rivet cutting chisel
Panel cutting chisel
Spot weld chisel
Bush splitting chisel
Sleeve grip
28
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - DRILL
No Description
6
7
4
5
1
2
3
Housing
Roll Pin
Exhaust Deflector
O-Ring
Air Inlet
Valve Stem
O-Ring
8
9
O-Ring
O-Ring
10 Bush
11 Reverse Selector
12 O-Ring
13 Spring
14 Trigger
15 End Plate
16 Bearing
No Description
17 End Plate
18 Cylinder
19 Rotor Blade
20 Steel Wire
21 Rotor Body
22 Front Support
23 Gear Wheel
24 Idler Gear
25 Pin
26 Drive Shaft
27 Bearing
28 Bearing
29 Nose Clamping Nut
30 Washer
31 Chuck (3/8”)
32 Chuck Securing Screw
29
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - DUAL ACTING SANDER
30
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
COMPONENT PARTS - DUAL ACTING SANDER
No Description
6
7
4
5
1
2
3
Bolt
Washer
Connector
Joint
Nut
6” Sanding pad
Circlip
8
9
Wave washer
Drive spindle
10 Bearing
11 Bolt
12 Orbital drive
13 Bolt
14 Woodruffe key
15 Anvil
16 Bearing
17 Cylinder end cap
18 Rotor
19 Rotor blade
20 Cylinder
21 Pin
22 O-ring
23 Bolt
24 Circlip
No Description
25 Motor housing
26 Bolt
27 Gasket
28 Housing
29 Housing grip
30 Circlip
31 O-ring
32 Speed regulator
33 Hand grip
34 O-ring
35 Air inlet plug
36 Spring
37 Valve stem
38 O-ring
39 O-ring
40 O-ring
41 Valve seat
42 Bracket
43 Washer
44 Washer
45 Nut
46 Screw
47 Nut
48 Trigger
31
Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]
Advertisement