CE™: .
HE™: .
cat Gui
1 3 nk or Suppl
A568B 1 Mi
1 2
1 Power
1 Angl
Power y nk
Power Cont ol Audi
SCTLi must al wi h or i mpor ant of Ci QuadCam, t act ce t ze SCT’ aci t
RCvent l on.
shel nt t
H001 [2]
RC8-CQC™ Installation Instructions
Updated: 7/17/2020
Supporting the Cisco Quad Camera and
Cisco SX80, Plus & Pro Codecs
TEST YOUR SCTLink™ CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your
SCTLink™ wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1. Test and verify your CAT6 STP or FUTP SCTLink™ cable for EIA568A/EIA568B.
The SCTLink™ cable must be between 10m (minimum) and 100m (maximum) length.
2. Connect one end of the SCTLink™ cable to the “ SCTLink™ ” connection on the Head End module.
3. Connect the other end of your SCTLink™ cable to the provided PowerSniffer.
4. Connect the WPS-48 power supply to the Head End module.
5. Connect the WPS-48 power supply to AC mains.
6. If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable .
7. Once your SCTLink™ cable has been tested, please disconnect the WPS-48 power supply from the RC8-HE module, and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1. Connect the RCC-C014 HDMI cables between the Quad
Camera’s HDMI 1 & 2 connectors (angled end) and the
RC8-CE’s “HDMI 1” and “HDMI 2” ports.
2. Connect the RCC-C037-0.3M UTP cable between the
Quad Camera’s RJ45 Ethernet port (angled end) and the
RC8-CE’s Ethernet port.
3. Connect the PPC-018 power cable between the Quad
Camera’s power connector and the RC8-CE’s “+12VDC
Output” port.
Connect the codec-end cables: corresponding “HDMI Out 1 A” and “HDMI Out 2 A” port.
5. Connect the 3ft RCC-H016 UTP control cable between the codec’s RJ45 camera Ethernet port and the RC8-
HE’s “Ethernet 1”.
Connect and Initiate the Extended System:
6. Connect one end of your SCTLink™ cable to the RC8-HE module’s blue “ SCTLink™ ” port.
7. Connect the other end of the SCTLink™ cable to the
RC8-CE module’s blue “ SCTLink™ ” port.
8. Connect the WPS-48 power supply to the RC8-HE.
4. Connect two 3ft RCC-H001 HDMI cables between the codec’s HDMI camera inputs and the RC8-HE’s
RC8-CE
RC8-HE
• ALLOW UP TO TWO MINUTES FOR THE QUAD CAMERA SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
OK LED 1 & 2
OK LED 1 & 2
INACTIVE
Blinking Green (~1 second interval)
Blinking Green (~1 second interval)
Blinking or Solid Red
Blinking or Solid Red
& Blinking
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC8-CQC™.
This kit is also inclusive of [1] RC-RKL™ Rack Shelf .
DESCRIPTION
[2] RCC-C014 1’ Angled HDMI Cables
RCC-C037-0.3M 1’ Angled UTP Cable
Video connection between Quad Camera and RC8-CE module.
Control connection (Ethernet) between Quad Camera and RC8-CE module.
PPC-018 1’ Power Cable
[2] RCC-H001 3’ HDMI Cables
RCC-H016 3’ UTP Cable
Power connection between Quad Camera and RC8-CE module.
Video connection between the codec and RC8-HE module.
Control connection (Ethernet) between the codec and RC8-HE module.
Power Supply Specifications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • © SOUND CONTROL TECHNOLOGIES, INC
