Honda FOREMAN RUBICON TRX500FM6 2018 Owner's Manual 269 Pages
advertisement
Contents
Contents These pages give an overview of the contents of your owner’s manual.
The first page of each section lists the topics covered in that section.
ATV Safety ..................................................................................1
Important safety information you should know, plus a look at the safety related labels on your ATV.
Instruments & Controls ..............................................................9
The location and function of indicators and controls on your ATV and operating instructions for various controls and features.
Before Riding ............................................................................55
The importance of wearing a helmet and other protective gear, how to make sure you and your ATV are ready to ride, and important information about loading.
Basic Operation & Riding .........................................................71
How to start and stop the engine, shift gears, and brake. Also, riding precautions.
Contents
31HR5630 Rubicon (TRX500FM6 4x4 with PS) MOM 16267 (1 7 04)
Contents
Servicing Your Honda ............................................................105
Why your ATV needs regular maintenance, what you need to know before servicing your Honda, an owner maintenance schedule, and instructions for specific maintenance and adjustment items.
Tips ..........................................................................................193
How to store and transport your ATV and how to be an environmentally responsible rider.
Taking Care of the Unexpected .............................................203
What to do if you have a flat tire, your engine won’t start, etc.
Technical Information ............................................................225
ID numbers, technical specifications, and other technical facts.
Consumer Information ...........................................................241
Information on warranties, emission controls, how to get Honda service manuals.
Index ........................................................................................248
Handy facts about fuel, engine oil, tire sizes, and air pressures.
Contents
2018
Honda
TRX500FM6 4×4 with Power Steering
FOREMAN RUBICON
OWNER’S MANUAL
FOR OFF-ROAD USE ONLY
This vehicle is designed and manufactured for off-road use only.
USA only:
It conforms to US EPA Noise Emission regulations, but does not conform to Federal Motor Vehicle Safety Standards or US EPA On
Highway Exhaust Emission regulations, and operation on public streets, roads, or highways is illegal. The vehicle is equipped with a
USDA qualified spark arrester. Obey local laws and regulations.
It conforms to US EPA, California, and Environment Climate Change
Canada emission regulations for ATVs.
Introduction
Introduction Congratulations on choosing your Honda ATV.
When you own a Honda, you’re part of a worldwide family of satisfied customers — people who appreciate Honda’s reputation for building quality into every product.
Your Honda was designed as a recreational ATV for off-road use by one rider only.
Before riding, take time to get acquainted with your ATV and how it works. To protect your investment, we urge you to take responsibility for keeping your ATV well maintained. Scheduled service is a must, of course. But it’s just as important to observe the break-in guidelines, and perform all pre-ride and other periodic checks detailed in this manual.
We also recommend that you read this owner’s manual before you ride. It’s full of facts, instructions, safety information, and helpful tips. To make it easy to use, the manual contains a detailed list of topics at the beginning of each section and an index at the back of the book.
As you read this manual, you will find information that is preceded by a
NOTICE
symbol. This information is intended to help you avoid damage to your Honda, other property, or the environment.
Read the Warranties Booklet (page 243) thoroughly so you
understand the coverages that protect your new Honda and are aware of your rights and responsibilities.
Whenever you ride, tread lightly. By staying on established trails and riding only in approved areas, you help protect the environment and keep off-road riding areas open for the future.
Introduction
Introduction
If you have any questions, or if you ever need special service or repairs, remember that your dealer knows your ATV best and is dedicated to your complete satisfaction.
Please report any change of address or ownership to your dealer so we will be able to contact you concerning important product information.
You may also want to visit our website at
USA: www.powersports.honda.com.
Canada: www.honda.ca.
Happy riding!
Introduction
A Few Words About Safety
A Few Words About Safety Your safety, and the safety of others, is very important. And operating this ATV safely is an important responsibility.
To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining an ATV. You must use your own good judgment.
You will find important safety information in a variety of forms, including:
Safety Labels — on the ATV.
Safety Messages — preceded by a safety alert symbol
2
and one of three signal words: DANGER , WARNING , or CAUTION .
A Few Words About Safety
A Few Words About Safety
These signal words mean:
3 DANGER
3 WARNING
3 CAUTION
You WILL be KILLED or
SERIOUSLY HURT if you don‘t follow instructions.
You CAN be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be HURT if you don’t follow instructions.
Safety Headings — such as Important Safety Reminders or
Important Safety Precautions.
Safety Section — such as ATV Safety.
Instructions — how to use this ATV correctly and safely.
This entire manual is filled with important safety information — please read it carefully.
A Few Words About Safety
ATV Safety
ATV Safety This section presents some of the most important information and recommendations to help you ride your ATV safely. Please take a few moments to read these pages. This section also includes information about the location of safety labels on your ATV.
Important Safety Information........................................................ 2
Safety Labels ................................................................................ 5
ATV Safety
1
Important Safety Information
Your ATV can provide many years of service and pleasure if you take responsibility for your own safety and understand the challenges you can meet while riding.
There is much that you can do to protect yourself when you ride.
You’ll find many helpful recommendations throughout this manual.
The following are a few that we consider to be most important.
Follow the Age Recommendation
The minimum recommended age for this ATV model is 16. Children under age 16 should never operate this vehicle. Refer to the age warnings provided in this manual and on the ATV.
Always Wear a Helmet
It’s a proven fact: helmets significantly reduce the number and severity of head injuries. So always wear an approved motorcycle helmet. We also recommend that you wear eye protection, sturdy
boots, gloves, and other protective gear (page 56).
Never Carry a Passenger
Your ATV is designed for one person only. There are no handholds, footrests, or seat for a second person, so never carry a passenger. A passenger could interfere with your ability to move around to maintain your balance and control of the ATV.
2
ATV Safety
Important Safety Information
Ride Off-road Only
Your ATV is designed and manufactured for off-road use only. The tires are not made for pavement, and the ATV does not have turn signals and other features required for use on public roads. If you need to cross a paved or public road, get off and walk your ATV across.
Take Time to Learn & Practice
Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.
Because many crashes involve inexperienced or untrained riders, we urge all riders to take a ATV operator course approved by the ATV
Safety Institute (ASI). See page 58.
Contact an authorized ATV dealer or call 1-800-887-2887 (USA only) to find out about the training courses nearest you.
Be Alert for Off-road Hazards
The terrain can present a variety of challenges when you ride offroad. Continually “read” the terrain for unexpected turns, drop-offs, rocks, ruts, and other hazards. Always keep your speed low enough to allow time to see and react to hazards.
ATV Safety
3
Important Safety Information
Ride within Your Limits
Pushing limits is another major cause of ATV crashes. Never ride beyond your personal abilities or faster than conditions warrant.
Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgments and ride safely.
Don’t Drink and Ride
Alcohol and riding don’t mix. Even one drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. So don’t drink and ride, and don’t let your friends drink and ride either.
Keep Your Honda in Safe Condition
It’s important to keep your ATV properly maintained and in safe riding condition. Having a breakdown can be difficult, especially if you are stranded off-road far from your base. To help avoid problems, inspect your ATV before every ride and perform all recommended maintenance.
4
ATV Safety
Safety Labels
Your ATV comes with a hang tag and several labels containing important safety information. Anyone who rides the vehicle should read and understand this information before riding.
The labels should be considered permanent parts of the vehicle. If a label comes off or becomes hard to read, contact your dealer for replacements.
ATV Safety
5
Safety Labels
WARNING
Improper ATV use can result in SEVERE INJURY or DEATH
ALWAYS USE
AN APPROVED
HELMET AND
PROTECTIVE
GEAR
NEVER USE
ON PUBLIC
ROADS
NEVER CARRY NEVER USE
PASSENGERS WITH DRUGS
OR ALCOHOL
NEVER operate: without proper training or instruction at speeds too fast for your skills or the conditions on public roads - a collision can occur with another vehicle with a passenger - passengers affect balance and steering and increase risk of losing control
A LWAY S : use proper riding techniques to avoid vehicle overturns on hills and rough terrain and in turns avoid paved surfaces - pavement may seriously affect handling and control
LOCATE AND READ OWNER'S MANUAL.
FOLLOW ALL INSTRUCTIONS AND WARNINGS.
6
ATV Safety
Safety Labels
Improper tire pressure or overloading can cause loss of control.
Loss of control can result in severe injury or death.
Cold tire pressure :
Front : 4.4
psi
Rear : 4.4
psi (
( 30
30 kPa) kPa)
Maximum weight capacity : 573 lbs. ( 260 kg)
WARNING
Overloading this ATV or carrying cargo improperly can change handling, stability and braking performance and can lead to an accident.
Never exceed the maximum front cargo limit of : 99 lbs ( 45 kg).
Refer to instructions in the Owner’s
Manual.
ATV Safety
7
Safety Labels
DRIVELINE INFORMATION
Driving in Front Differential Lock Mode changes the way your vehicle handles and turns. Use this mode only at low speed. See owner’s manual for more information.
NEVER ride as a passenger.
Passengers can cause a loss of control, resulting in
SEVERE INJURY or DEATH.
BRAKING INFORMATION
With four-wheel drive, operating any brake control causes braking at both the front and rear wheels.
For detailed braking information, refer to the
Owner's Manual.
(For Canada)
Operating this ATV if you are under the age of 16 increases your chance of severe injury or death.
NEVER operate this ATV if you are
under age 16 .
WARNING
Improper ATV use can result in SEVERE INJURY or DEATH
Towing an improperly loaded trailer can cause loss of control.
Read towing instructions in owner's manual
Tow weight limit : 1322 lbs. ( 600 kg)
Tongue weight : 30 lbs. ( 14 kg)
WARNING
Overloading this ATV or carrying cargo improperly can change handling, stability and braking performance and can lead to an accident.
Never exceed the maximum rear cargo limit
(combined weight on the rear rack and in the storage area) of : 187 lbs ( 85 kg).
Refer to instructions in the Owner’s
Manual.
ALWAYS USE
AN APPROVED
HELMET AND
PROTECTIVE
GEAR
NEVER USE
ON PUBLIC
ROADS
NEVER CARRY NEVER USE
PASSENGERS WITH DRUGS
OR ALCOHOL
NEVER operate: without proper training or instruction at speeds too fast for your skills or the conditions on public roads - a collision can occur with another vehicle with a passenger - passengers affect balance and steering and increase risk of losing control
A LWAY S : use proper riding techniques to avoid vehicle overturns on hills and rough terrain and in turns avoid paved surfaces - pavement may seriously affect handling and control
LOCATE AND READ OWNER'S MANUAL.
FOLLOW ALL INSTRUCTIONS AND WARNINGS.
8
ATV Safety
Instruments & Controls
Instruments & Controls This section shows the location of all indicators and controls you would normally use before or while riding your ATV.
The items listed on this page are described in this section.
Instructions for other components are presented in other sections of this manual where they will be most useful.
Operation Component Locations ................................................ 11
Indicators & Displays ................................................................... 14
Multi-function Display.............................................................. 20
Speed and Mileage Unit Changing........................................... 22
4WD Indicator ......................................................................... 22
Gear Position Indicator............................................................. 23
Fuel Gauge .............................................................................. 24
Digital Clock ............................................................................ 26
Odometer................................................................................ 27
Tripmeter................................................................................. 27
Coolant Temperature Gauge ................................................... 28
Hourmeter............................................................................... 30
Maintenance Tripmeter/Maintenance Hourmeter ..................... 31
(cont’d)
Instruments & Controls
9
Instruments & Controls
Controls & Features .................................................................... 34
Ignition Switch......................................................................... 34
4WD Switch ............................................................................ 35
Front Differential Lock and Speed Limiter Over-Ride (Differential
Lock Switch and Start/Over Ride Button)................................. 36
Start/Over Ride Button ............................................................. 39
Engine Stop Switch.................................................................. 40
Headlight Switch ..................................................................... 41
Headlight Dimmer Switch ........................................................ 41
Recoil Starter (Canada only) ..................................................... 42
Throttle Lever .......................................................................... 43
Front Brake Lever..................................................................... 44
Rear Brake Lever/Parking Brake Lever ....................................... 44
Rear Brake Pedal...................................................................... 44
Parking Brake/Reverse Lever (P/R Lever) .................................... 45
Flag Pole Bracket ..................................................................... 47
Trailer Hitch ............................................................................. 48
Accessory Socket ..................................................................... 49
Utility Box ................................................................................ 51
Utility Pocket ........................................................................... 52
Storage Compartment ............................................................. 53
PS (Electric Power Steering)...................................................... 54
10
Instruments & Controls
Operation Component Locations rear brake lever/ parking brake lever
P/R lever headlight switch front brake lever
4WD switch ignition switch throttle lever engine stop switch start/over ride button differential lock switch headlight dimmer switch
Instruments & Controls
11
Operation Component Locations rear cargo rack front cargo rack flag pole bracket rear brake pedal recoil starter
(Canada only)
12
Instruments & Controls
Operation Component Locations accessory socket utility box utility pocket shift lever trailer hitch storage compartment
Instruments & Controls
13
Indicators & Displays
The indicators and displays on your ATV keep you informed, alert you to possible problems, and make your riding safer and more enjoyable. Refer to the indicators frequently. Their functions are described on the following pages.
(1) (2) (3) (4)
(8)
(1) neutral indicator
(2) reverse indicator
(3) differential lock indicator
(4) PGM-FI indicator
(7) (6) (5)
(5) high coolant temperature indicator
(6) PS (Electric Power Steering) indicator
(7) multi-function display
(8) mode select button
14
Instruments & Controls
Indicators & Displays
Lamp Check
Initial lamp check:
The indicators come on for a few seconds and then go off when you turn the ignition switch to ON ( q ).
The PS (Electric Power Steering) indicator comes back on and remains on until the engine is started after initial lamp check.
The high coolant temperature indicator and PGM-FI indicator comes back on for a few seconds and then go off after initial lamp check.
These indicators are identified in the table on page 17 with the
words: Lamp Check .
When applicable, the reverse or neutral indicators comes back on and remain on until you shift out of reverse or neutral after initial lamp check.
When applicable, the differential lock indicator comes back on and remains on until you shift out of the front differential lock mode after initial lamp check.
If one of these indicators does not come on when it should, have your dealer check for problems.
Instruments & Controls
15
Indicators & Displays
Display Check
When the ignition switch is turned on, the multi-function display (1) will temporarily show all the modes and digital segments and initial message. So you can make sure the liquid crystal display is functioning properly.
The displays are identified in the table on page 18 with the words:
Display Check .
If any part of these displays does not come on when it should, have your dealer check for problems.
(1)
(1) multi-function display
Meter Input Signal Failure
If the neutral indicator, reverse indicator, differential lock indicator,
PGM-FI indicator, high coolant temperature indicator stay on and the gear position indicator “–” and coolant temperature gauge
“C – – – – – H” blink, have your dealer check for problems.
16
Instruments & Controls
1 Neutral indicator
2 Reverse indicator
3 Differential lock indicator
4 PGM-FI indicator
5 High coolant temperature indicator
Indicators & Displays
Lights when the transmission is in neutral. Lamp Check .
Lights when the transmission is in reverse. Lamp Check .
Lights when the front differential lock mode is engaged. Should also light for a few seconds and go off when the ignition switch is turned on, and then come back on and remain on until the differential lock switch or the ignition switch is turned off. If the indicator blinks with the 4WD indicator, there is any abnormality in the differential
Lamp Check .
Lights when there is any abnormality in the PGM-FI (Programmed Fuel
Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned on. If the indicator comes on at any other time, reduce speed and take your vehicle to your dealer as soon as possible. Lamp
Check .
Lights when coolant temperature is high enough to adversely affect the service life of the engine.
If the high coolant temperature indicator comes on while you are riding, immediately bring the vehicle to a stop, turn the engine off and let it
Lamp Check .
(cont’d)
Instruments & Controls
17
Indicators & Displays
6 PS (Electric Power
Steering) indicator
7 Multi-function display
4WD indicator
Lights when there is an abnormality in the PS (Electric Power Steering)
Lamp Check .
The display includes the following functions. Display Check .
Shows when the 4WD drive mode is engaged. If the indicator blinks with the differential lock indicator when there is any abnormality in the
differential system. See page 38.
Shows the gear position (page 23).
Gear position indicator
Maintenance minder indicator
Speedometer
Fuel gauge
Digital clock
Odometer
Tripmeter
Coolant temperature gauge
Hourmeter
Shows when specified maintenance
interval is reached (page 32).
Shows riding speed.
Shows approximate fuel supply
Shows the time (hours and minutes)
Shows accumulated mileage
Shows mileage per trip (page 27).
Shows approximate coolant
Maintenance tripmeter
Maintenance hourmeter
Shows hours and tenths of hours of
Inform when the mileage or operating hours on your ATV approaches and passes the interval specified on the
maintenance schedule (page 31).
18
Instruments & Controls
8 Mode select button
Indicators & Displays
Selects display in the lower parts of multi-function display. Adjusts the
digital clock (page 26). Changes the
speed and mileage units (page 22).
Resets the tripmeter to zero (0)
(page 27). This button also used to
reset the maintenance tripmeter and
maintenance hourmeter (page 33).
Instruments & Controls
19
Indicators & Displays
Multi-function Display
The multi-function display (1) includes the following functions:
4WD indicator Odometer
Gear position indicator
Speedometer
Tripmeter
Coolant temperature gauge
Maintenance minder indicator Hourmeter
Fuel gauge Maintenance tripmeter
Digital clock Maintenance hourmeter
(1) (2) (3)
(7) (6)
(1) multi-function display
(2) gear position indicator
(3) speedometer
(4) maintenance minder indicator
(5) (4)
(5) lower part of the multi-function display
(6) 4WD indicator
(7) mode select button
The lower part of the multi-function display (5) shows the fuel gauge, digital clock, odometer, tripmeter, coolant temperature gauge, hourmeter, maintenance tripmeter or maintenance hourmeter. To change the lower part of the multi-function display, push the mode select button (7).
20
Instruments & Controls
Indicators & Displays
Each time you press the mode select button, mode will change as shown in the illustration.
Maintenance tripmeter
Coolant temperature
When ATV is moving
When ATV is not moving
Maintenance hourmeter
If there is a fuel warning with your ATV, the display will automatically change to the fuel gauge. If you try to change the display back to ordinary display, it will automatically return to the fuel gauge.
If there is a coolant temperature warning with your ATV, the display will automatically change to the coolant temperature gauge. If you try to change the display back to ordinary display, it will automatically return to the coolant temperature gauge.
Instruments & Controls
21
Indicators & Displays
Speed and Mileage Unit Changing
The speedometer, odometer, tripmeter, and maintenance tripmeter show in either “MPH” and “MILE” or “KM/H” and “KM”.
To change the speed and mileage units, press and hold the mode select button (1) for more than 5 seconds in the odometer mode
(page 21) with the ATV stopped.
(1)
(1) mode select button
4WD Indicator
The 4WD indicator (1) shows when the 4WD mode engages
(1)
(1) 4WD indicator
22
Instruments & Controls
Indicators & Displays
Gear Position Indicator
The gear position indicator (1) shows the gear position when the ignition switch is in the ON ( q ) position.
The indicator displays: N for neutral, R for reverse, and 1 – 5 for the five forward gears.
“–” will be displayed on the gear position indicator when the transmission is not shifted into gear properly. Before riding, check that the gear position is properly displayed on the gear position indicator.
If the gear position indicator shows “–” or blinks, turn the ignition switch to the OFF ( w ) position, and then turn it back to the ON ( q ) position again.
If the gear position indicator shows “–”, rock the vehicle back and forth and make sure the gear position indicator is displayed properly and then if the gear position indicator still shows “–” or blinks, see your dealer.
If the “–” on the gear position indicator is blinking, see your dealer.
(1)
(1) gear position indicator
Instruments & Controls
23
Indicators & Displays
Fuel Gauge
The fuel gauge (1) shows the approximate fuel supply available with the fuel mark (2). The fuel tank capacity is:
3.88 US gal (14.7 ℓ)
(2)
(1) fuel gauge
(1)
(2) fuel mark
Regardless of what mode the display is in, when the fuel level reaches 1st segment (3), the display will automatically switch to the fuel gauge display. You should refuel as soon as possible.
The amount of fuel remaining when the fuel gauge reaches the 1st segment is approximately:
1.82 US gal (6.9 ℓ)
(3)
(3) 1st segment
24
Instruments & Controls
Indicators & Displays
(4)
(4) “E _ _ _ _ _ F”
(5)
(5) “LO FUEL”
When the fuel gauge show “E _ _ _ _ _ F” (4) and “LO FUEL” (5) blink 3 times alternately and fuel mark blinks, you should refuel as soon as possible.
The amount of fuel reserve is approximately:
1.29 US gal (4.9 ℓ)
Fuel gauge failure:
If the fuel gauge E – – – – – F (6) is blinking, the fuel gauge function failed. See your dealer.
(6) “E – – – – – F”
(6)
Instruments & Controls
25
Indicators & Displays
Digital Clock
The digital clock (1) shows time with the clock mark (2) when the ignition switch is ON ( q ).
(3)
(1) digital clock
(2) clock mark
(1) (2)
(3) mode select button
To adjust the time, proceed as follows:
1. Turn the ignition switch ON ( q ) and select the digital clock mode.
2. Press and hold the mode select button (3) until the display start blinking.
3. To advance the display 1 minute at a time, press and release the mode select button for 0.5 seconds.
Press and hold the mode select button the display will begin advancing fast. Press and hold the button for:
• 0.5 – 5.5 seconds: advance one minute at a time.
• 5.5 – 10.5 seconds: advance five minutes at a time.
• 10.5 seconds or more: advance ten minutes at a time.
4. Release the mode select button when the display reaches the desired time.
5. To end the adjustment, press and release the mode select button for less than 0.5 seconds or turn the ignition switch to OFF ( w ).
After the battery is reconnected (page 185), check the clock.
Readjust the clock if necessary.
26
Instruments & Controls
Indicators & Displays
Odometer
The odometer (1) registers total distance traveled in mileage while the ignition switch is ON ( q ) with the “ODO” mark (2). The odometer locks at 999,999 when the readout exceeds 999,999.
(2)
(1) odometer
(1)
(2) “ODO” mark
Tripmeter
The tripmeter (1) shows mileage per trip since you last reset the tripmeter while the ignition switch is ON ( q ) with the “TRIP” mark
(2). The tripmeter returns to 0.0 when the readout exceeds 999.9. To reset the tripmeter to zero, press the mode select button (3) and hold it in for at least 2 seconds in the tripmeter mode.
(2)
(3)
(1) tripmeter
(2) “TRIP” mark
(1)
(3) mode select button
Instruments & Controls
27
Indicators & Displays
Coolant Temperature Gauge
The coolant temperature gauge (1) shows coolant temperature with the coolant temperature mark (2) while the ignition switch is ON ( q ).
The normal operating temperature range is within the section between the 1st segment (3) and 4th segment (4).
When coolant temperature is low, the coolant temperature gauge will display “Lo” (5).
(2)
(1) (3) (4)
(1) coolant temperature gauge (4) 4th segment
(2) coolant temperature mark (5) “Lo”
(3) 1st segment
(5)
28
Instruments & Controls
Indicators & Displays
When the coolant is over specified temperature, the 5th segment (6) appears and the high coolant temperature indicator (7) lights.
If this occurs, stop the engine and check the reserve tank coolant level.
Read pages 213 – 214 and do not ride the ATV until the problem has
been corrected.
NOTICE
Continuing to ride with an overheated engine can cause serious engine damage.
(6) (7)
(6) 5th segment (7) high coolant temperature indicator
If the “C – – – – – H” (8) blinks, the meter input signal fails. See your dealer.
(8) “C – – – – – H”
(8)
Instruments & Controls
29
Indicators & Displays
Hourmeter
The hourmeter (1) shows accumulated hours while the ignition switch is ON ( q ) with the hourmeter mark (2). The hourmeter provides accurate service period information for initial and regular maintenance. The hourmeter locks at 99,999.9 when the readout exceeds 99,999.9.
(1) hourmeter
(1) (2)
(2) hourmeter mark
30
Instruments & Controls
Indicators & Displays
Maintenance Tripmeter/Maintenance Hourmeter
The maintenance tripmeter (1) shows mileage to maintenance while the ignition switch is ON ( q ) with the maintenance minder indicator
(2).
The maintenance hourmeter (3) shows remaining time to maintenance while the ignition switch is ON ( q ) with the maintenance minder indicator.
(1) (2)
(1) maintenance tripmeter
(2) maintenance minder indicator
(3) (2)
(3) maintenance hourmeter
The maintenance tripmeter decreases from 600 miles (1,000 km) after reset. The maintenance hourmeter decreases from 100 hour after reset.
Initial setting of the maintenance tripmeter is 100 miles (150 km).
Initial setting of the maintenance hourmeter is 20 hour.
(cont’d)
Instruments & Controls
31
Indicators & Displays
Maintenance Minder Indicators:
Initial Maintenance
Appears at 100 miles (150 km) or 20 operating hours, whichever comes first.
Regular Maintenance Interval 1
Appears 600 miles (1,000 km) or 100 operating hours after the Initial Maintenance or Regular
Maintenance Interval 2 is performed and maintenance minder is reset, whichever comes first in the maintenance schedule.
Regular Maintenance Interval 2
Appears 600 miles (1,000 km) or 100 operating hours after Regular Maintenance Interval 1 is performed and maintenance minder is reset, whichever comes first in the maintenance schedule.
When the maintenance tripmeter or maintenance hourmeter amounts to 0, the display of the maintenance minder indicator changes. When selected the maintenance tripmeter or maintenance hourmeter, the maintenance minder indicator and lower part of the multi-function display (4) start blinking. When selected other mode, the maintenance minder indicator appears in the display.
(4) (4)
(4) lower part of the multi-function display
32
Instruments & Controls
Indicators & Displays
Reset the maintenance tripmeter/maintenance hourmeter after maintenances.
To reset the maintenance tripmeter/maintenance hourmeter, proceed as follows:
Press and hold the mode select button (5) and turn the ignition switch (6) to ON ( q ). The maintenance minder indicator will appear, then it will blinks twice, and the multi-function display will temporarily show all the modes and digital segments. The indicator message will disappear.
Reset operation will be cancelled, if the mode select button is released before the indicator blinks twice.
If the maintenance is done before the setting interval, be sure to reset the meters after the maintenance.
(5)
(6)
(2) maintenance minder indicator
(2)
(5) mode select button
(6) ignition switch
Instruments & Controls
33
Controls & Features
Ignition Switch
The ignition switch (1) is used for starting and stopping the engine
(page 78). Insert the key and turn it to the right for the ON (
q ) position.
The ignition switch is also used to reset the maintenance tripmeter/
maintenance hourmeter (page 33).
Key Position
ON ( q )
OFF ( w )
CENTER OF HANDLEBAR
OFF
Function
Electrical circuits on.
No electrical circuits function.
ON
(1)
(1) ignition switch q ON w OFF
34
Instruments & Controls
Controls & Features
4WD Switch
Your ATV is equipped with a 4WD switch (1), which permits a choice between the “2WD” and “4WD” drive modes. Select a drive mode that’s suitable for your riding.
Keep both hands on the handlebar while machine is in motion and come to a complete stop before using the 4WD switch.
The 4WD switch is located above the throttle lever. To select the drive mode, with your ATV stopped, push the 4WD switch.
To check your present drive mode, look at the 4WD indicator (2).
2WD mode: the 4WD indicator disappears when the 2WD mode engages.
4WD mode: the 4WD indicator appears when the 4WD mode engages.
If the 4WD indicator does not appear when selecting the 4WD mode, accelerate your ATV slowly until the 4WD indicator appears.
The 4WD indicator and differential lock indicator both flash together when there is any abnormality in the differential system. See Front
Differential Lock and Speed Limiter Over-Ride (Differential Lock
Switch and Start/Over Ride Button)
2WD mode
2WD mode
(2)
(1)
4WD mode
4WD mode
(1) 4WD switch
(1)
(2) 4WD indicator
Instruments & Controls
35
Controls & Features
Front Differential Lock and Speed Limiter Over-Ride
(Differential Lock Switch and Start/Over Ride Button)
Your ATV is equipped with a front differential lock feature that includes a speed limiter and speed limiter over-ride. This system is designed to provide maximum use of available traction to help you escape from situations where the vehicle might otherwise become stuck, in the mud for example. When the front differential lock mode is activated, the front differential gear is locked causing all four wheels to rotate at the same speed. Because locking all four wheels together changes the way the vehicle handles and increases the amount of room necessary to turn, a speed limiter restricts the speed to 20 mph (32 km/h). Pushing and holding the start/over ride button in this mode allows you to momentarily over-ride the 20 mph
(32 km/h) speed limiter, up to 40 mph (64 km/h), to help you free the vehicle in more severe conditions. You should only use this feature where maximum traction is required and only in low speeds. For normal riding, use 2WD and 4WD modes.
36
Instruments & Controls
Controls & Features
To select the front differential lock mode:
When the 4WD mode is engaged, reduce the speed of your ATV to below 10 mph (16 km/h) and slide the differential lock switch (1) over the 4WD switch. The differential lock indicator (2) will flash fast and the front differential locking process begins. When the locking is complete, the differential lock indicator stays on.
4WD mode front differential lock mode off
(1)
(2)
(in the locking process) fast flashing
(2)
(1)
(completed locking)
(2)
(speed above 10 mph
(16 km/h). Locking process interrupted) slow flashing
(2) solid light
(1) differential lock switch (2) differential lock indicator
If the speed of your ATV is above 10 mph (16 km/h), the locking process will be interrupted and the differential lock indicator will slowly flash.
If the differential lock indicator does not stay on when the front differential lock mode is selected, steer the handlebar either to the left or right all the way while your ATV is stopped. If the differential lock indicator is still flashing, move your ATV slowly while steering the handlebar all the way to right or left.
Instruments & Controls
37
Controls & Features
To activate the speed limiter over-ride mode:
Push the start/over ride button (3) when the front differential lock mode is activated.
LEFT HANDLEBAR
(3)
(3) start/over ride button
Differential system failure:
The differential lock indicator and 4WD indicator (4) will both flash when there is any abnormality in the differential system. If this occurs, the differential actuator will stop moving, and the differential system will be fixed in the current position, either 2WD mode, 4WD mode or front differential lock mode.
If both the differential lock indicator and 4WD indicator flash, reduce speed and take your ATV to your dealer as soon as possible.
(2) (4)
(2) differential lock indicator
38
Instruments & Controls
(4) 4WD indicator
Start/Over Ride Button
LEFT HANDLEBAR
Controls & Features
(1)
(1) start/over ride button
START or SPEED LIMITER
OVER-RIDE MODE
The start/over ride button (1) is used for starting the engine and activate the speed limiter over-ride mode.
Pushing the button in starts the engine. See Starting Procedure ,
When the engine is not running and the start/over ride button is pushed, the starter motor will crank the engine. The starter motor will not operate if the engine stop switch is in the OFF ( r ) position when the start/over ride button is pushed.
To activate the speed limiter over-ride mode, see Front Differential
Lock and Speed Limiter Over-Ride (Differential Lock Switch and Start/
Over Ride Button)
Instruments & Controls
39
Controls & Features
Engine Stop Switch
LEFT HANDLEBAR e r
(1)
(1) engine stop switch r OFF e RUN
The engine stop switch (1) is used to stop the engine in an emergency. To operate, slide the switch to the OFF ( r ) position. The switch must be in the RUN ( e ) position to start the engine, and it should normally remain in the RUN ( e ) position even when the engine is OFF.
If your ATV is stopped with the ignition switch ON ( q ) and the engine stop switch OFF ( r ), the battery will discharge. Turn the ignition switch to OFF ( w ) to prevent battery discharge.
40
Instruments & Controls
Headlight Switch
LEFT HANDLEBAR
(1)
Controls & Features y t
(2)
(1) headlight switch
(2) headlight dimmer switch y ON t OFF u HI i LO
The headlight switch (1) is used to turn the headlights and assist headlight ON ( y ) or OFF ( t ). The assist headlight turns on only when the dimmer switch (2) is in the HI ( u ) position.
To operate, turn the switch to ON ( y ) or OFF ( t ).
Headlight Dimmer Switch
u i
The headlight dimmer switch (2) is used to change between the high and low beams of the headlights and to activate the assist headlight.
To operate, turn the switch to HI ( u ) for high beam of the headlights and activate the assist headlight, LO ( i ) for low beam of the headlights and deactivate the assist headlight.
Instruments & Controls
41
Controls & Features
Recoil Starter (Canada only)
RIGHT SIDE
(1)
(1) recoil starter
The recoil starter (1) is used to start the engine when the battery is low. See Using the Recoil Starter (Canada only)
42
Instruments & Controls
Throttle Lever
RIGHT HANDLEBAR
Controls & Features
(A)
(1)
(A) to open the throttle (1) throttle lever
The throttle controls engine rpm (speed). To increase engine rpm, press the throttle lever (1) with your thumb. To reduce engine rpm, release pressure on the throttle lever. The throttle will automatically return to the closed position (engine idle) when you remove your thumb.
Instruments & Controls
43
Controls & Features
Front Brake Lever
The front brake lever is used to slow or stop your ATV. To operate,
pull the lever. For information on braking techniques, see page 89.
Rear Brake Lever/Parking Brake Lever
The rear brake lever/parking brake lever is used to slow or stop your
ATV. To operate, pull the lever. For information on braking
Rear Brake Pedal
The rear brake pedal is used to slow or stop your ATV. To operate, depress the pedal. For information on braking techniques, see
44
Instruments & Controls
Controls & Features
Parking Brake/Reverse Lever (P/R Lever)
LEFT HANDLEBAR
(1)
(2)
(1) P/R lever
(2) rear brake lever/parking brake lever
The P/R lever (1) on the rear brake lever/parking brake lever (2) is used to apply the parking brake or to shift the transmission into reverse.
(cont’d)
Instruments & Controls
45
Controls & Features
To apply the parking brake:
Bring the vehicle to a complete stop, then make sure the transmission is in neutral.
Squeeze the rear brake lever /parking brake lever (1), then rotate the
P/R lever (2) clockwise until it engages the slot on the rear brake lever/parking brake lever bracket.
For more information on Parking
(2)
(1)
(1) rear brake lever/parking brake lever
(2) P/R lever
To release the parking brake:
Squeeze the rear brake lever/parking brake lever until the P/R lever is released from the slot on the rear brake lever/parking brake lever bracket.
The brake light is activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch to OFF
( w ) to avoid discharging the battery.
To shift the transmission into reverse:
See Riding in Reverse
46
Instruments & Controls
Flag Pole Bracket
RIGHT REAR
Controls & Features
(1)
(1) flag pole bracket
Flag poles are optional equipment available from your dealer. To mount a pole in the bracket (1), follow the instructions that come with the flag pole kit.
Flag poles are required in some riding areas. Check local regulations before riding.
Instruments & Controls
47
Controls & Features
Trailer Hitch
REAR (2)
(1) trailer hitch
(1)
(2) ball
The trailer hitch (1) is located on the rear frame. To use the hitch, you’ll need a proper size ball (2) as specified by the trailer manufacturer.
To attach the ball and properly hook up a trailer, follow the trailer manufacturer’s instructions. For load limits and operational
48
Instruments & Controls
Accessory Socket
LEFT FRONT
(2)
Controls & Features
(3)
(1) accessory socket
(2) front center cover
(1)
(3) accessory socket cap
The accessory socket (1) is attached to the left side of the front center cover (2). You can use the accessory socket to power a trouble light, spotlight, CB radio, or cell phone, etc.
NOTICE
Do not plug in any heat-generating accessory, such as an automobile cigarette lighter, because it can damage the socket.
To use the accessory socket, turn the ignition switch to ON ( q ), start the engine. Then turn the headlights OFF ( t ), and open the accessory socket cap (3).
(cont’d)
Instruments & Controls
49
Controls & Features
Be sure the engine is on and the headlights are turned off before using the accessory socket, otherwise you may drain the battery.
The accessory socket’s rated capacity is DC 12 V, 120 Watts (10 A) or less. If you exceed this limit, you may blow a fuse. See If a Fuse
Blows
When you are done using an accessory, unplug it, and cover the socket with the cap.
Be careful not to flood this accessory socket when washing your
ATV.
50
Instruments & Controls
Controls & Features
Utility Box
The utility box (1) is located on the left side of the front fender. You may store small, lightweight items in the box.
To open:
Pull up the front of the utility box cover (2).
To close:
Push down the front of the utility box cover until it locks in place.
Make sure that the stud (3) is locked securely in position by pulling up lightly on the front of the utility box cover.
LEFT FRONT FENDER
(3)
(2)
(1) utility box
(2) utility box cover
(3) stud
(1)
Instruments & Controls
51
Controls & Features
Utility Pocket
The utility pocket (1) is located on the left side cover. You may store small, lightweight items in the pocket.
NOTICE
Do not store valuable item in the utility pocket.
LEFT SIDE COVER
(1) utility pocket
52
Instruments & Controls
(1)
Controls & Features
Storage Compartment
The storage compartment (1) is located below the rear cargo rack
(2).
To open the compartment, unhook the rubber strap (3).
Be careful not to flood this area when washing your ATV.
REAR
(2) (3)
(1) storage compartment
(2) rear cargo rack
(3) rubber strap
(1)
Instruments & Controls
53
Controls & Features
PS (Electric Power Steering)
This ATV is equipped with an electronically controlled, electricpower-assisted steering system.
While the engine is running, the PS (Electric Power Steering) system provides power from the electric motor, which helps you to turn the
ATV’s handlebar more easily.
The PS system on this ATV utilizes an overheat protection feature to prevent damage to system components. In certain extended, repetitive high-load situations, the system will reduce or even disable power steering assist. The steering will perform as a normal non-PS system during this brief period. After cooling down, it will then return to normal PS operation.
The PS indicator should light when the ignition switch is turned on and remain on until the engine is started.
The PS indicator also lights when there is any abnormality in the PS system. If this occurs, the electric power assist for turning will not be available, but the manual steering system will perform as usual.
If the PS indicator lights at any time while riding, reduce speed and take your ATV to your dealer as soon as possible. Continuing to ride with a PS system problem can cause system damage.
Do not modify your Electric Power Steering system. In case of a malfunction, take your ATV to your dealer.
54
Instruments & Controls
Before Riding
Before Riding Before each ride, you need to make sure you and your Honda are both ready to ride. To help get you prepared, this section discusses how to evaluate your riding readiness, what items you should check on your ATV, and adjustments to make for your comfort, convenience, or safety. This section also includes important information about loading.
Are You Ready to Ride? .............................................................. 56
Protective Apparel ................................................................... 56
Rider Training .......................................................................... 58
Age Recommendation ............................................................. 59
No Passengers ......................................................................... 59
No Alcohol or Drugs ................................................................ 60
Is Your ATV Ready to Ride? ........................................................ 61
Pre-ride Inspection ................................................................... 61
Load Limits & Guidelines............................................................. 65
Loading ................................................................................... 65
Load Limits .............................................................................. 66
Loading Guidelines .................................................................. 67
Accessories & Modifications........................................................ 68
Accessories .............................................................................. 68
Modifications........................................................................... 69
Before Riding
55
Are You Ready to Ride?
Before you ride your ATV for the first time, we urge you to:
• Read this owner’s manual and the labels on your ATV carefully.
• Make sure you understand all the safety messages.
• Know how to operate all the controls.
Before each ride, be sure:
• You feel well and are in good physical and mental condition.
• You are wearing an approved motorcycle helmet (with chin strap tightened securely), eye protection, and other protective clothing.
• You don’t have any alcohol or drugs in your system.
Protective Apparel
For your safety, we strongly recommend that you always wear an approved motorcycle helmet, eye protection, boots, gloves, long pants, and a long-sleeved shirt or jacket whenever you ride.
Although complete protection is not possible, wearing proper gear can reduce the chance of injury when you ride.
Following are suggestions to help you choose the proper gear.
Helmet and Eye Protection
Your helmet is your most important piece of riding gear because it offers the best protection against head injuries. A helmet should fit your head comfortably and securely.
56
Before Riding
Are You Ready to Ride?
An open-face helmet offers some protection, but a full-face helmet offers more. Regardless of the style, look for a DOT (Department of
Transportation) sticker on any helmet you buy (USA only). Always wear a face shield or goggles to protect your eyes and help your vision.
WARNING 3 WARNING
Operating this ATV without wearing an approved motorcycle helmet, eye protection, and protective clothing could increase your chances of severe injury or death in the event of a crash.
Always wear an approved motorcycle helmet that fits properly and wear eye protection
(goggles or face shield), gloves, boots, longsleeved shirt or jacket and long pants.
Additional Riding Gear
In addition to a helmet and eye protection, we also recommend:
• Sturdy off-road motorcycle boots to help protect your feet, ankles, and lower legs.
• Off-road motorcycle gloves to help protect your hands.
• Riding pants with knee and hip pads, a riding jersey with padded elbows, and a chest/shoulder protector.
Before Riding
57
Are You Ready to Ride?
Rider Training
Developing your riding skills is an on-going process. Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice riding the ATV in a safe area to build your skills. Do not ride in rough terrain until you get accustomed to the ATV’s controls, and feel comfortable with its size and weight.
We urge all riders to take an ATV operator course approved by the
ATV Safety Institute (ASI). For information about the ASI training course nearest you, call the national toll-free number; (800) 887-
2887 (USA only).
Other riding tips can be found in the Tips & Practice Guide for the
ATV Rider booklet that came with your ATV (USA only).
WARNING 3 WARNING
Operating this ATV without proper instruction could increase your risk of a crash which could lead to serious injury or death.
Beginning and inexperienced operators should complete the certified training course offered by Honda. They should then regularly practice the skills learned in the course and the operating techniques described in the owner’s manual.
58
Before Riding
Are You Ready to Ride?
Age Recommendation
The minimum recommended age for this ATV model is 16. For safety, never let children under 16 years old operate this vehicle.
WARNING 3 WARNING
A child using an ATV that is not recommended for their age could lose vehicle control while riding, resulting in severe injury or death.
A child under 16 should never operate an ATV with engine size greater than 90cc.
No Passengers
This ATV is designed as an operator-only vehicle. The long seat is designed to allow the rider to change body position, not for carrying a passenger. Never let a passenger ride on the seat or on the front or rear cargo racks.
WARNING 3 WARNING
Carrying a passenger on this ATV greatly reduces your ability to balance and control this ATV and could cause a crash and you or your passenger could be injured or killed.
Never carry a passenger on this ATV.
Before Riding
59
Are You Ready to Ride?
No Alcohol or Drugs
Alcohol, drugs and ATVs don’t mix. Even a small amount of alcohol can impair your ability to operate an ATV safely. Likewise, drugs — even if prescribed by a physician — can be dangerous while operating an ATV. Consult your doctor to be sure it is safe to operate a vehicle after taking medication.
WARNING 3 WARNING
Operating this ATV after consuming alcohol or drugs can seriously affect your judgment, cause you to react more slowly, affect your balance and perception, and result in serious injury or death.
Never consume alcohol or drugs before or while operating this ATV.
60
Before Riding
Is Your ATV Ready to Ride?
Before each ride, it’s important to inspect your ATV and make sure any problem you find is corrected. A pre-ride inspection is a must, not only for safety, but because having a breakdown, or even a flat tire, can be a major inconvenience.
If your ATV has overturned or been involved in a collision, do not ride the vehicle until it has been inspected by your dealer. There may be damage or other problems you cannot see.
WARNING 3 WARNING
Improperly maintaining this ATV or failing to correct a problem before riding can cause a crash in which you can be seriously hurt or killed.
Always perform a pre-ride inspection before every ride and correct any problems.
Pre-ride Inspection
Check the following items before you get on the ATV:
Engine Oil
Radiator Coolant
Check the level and add oil if needed
Check for leaks.
Check the coolant level and add coolant if
Check for leaks.
(cont’d)
Before Riding
61
Is Your ATV Ready to Ride?
Fuel
Tires
Check the level and add fuel (page 125) if
needed. Also make sure the fuel fill cap is securely fastened.
Check for leaks.
Use a gauge to check the air pressure. Adjust if needed. Also look for signs of damage or
Check for damage or looseness (pages 181).
Drivetrain Boots
Guards
Nuts & Bolts Check the wheels to see that the axle nuts are tightened. Use a wrench to make sure all accessible nuts, bolts, and fasteners are tight.
Underbody & Exhaust
System
Check for, and remove, any dirt, vegetation or other debris that could be a fire hazard or interfere with the proper operation of the vehicle.
Air Cleaner Housing
Drain Tube
Check for deposits in the drain tube. If
necessary, clean the tube (page 153) and
check the air cleaner housing.
Leaks, Loose Parts Walk around your ATV and look for anything that appears unusual, such as a leak or loose cable.
62
Before Riding
Is Your ATV Ready to Ride?
Cable
Lights
Check the cable housings for wear. Check the fittings for looseness. Replace or tighten as needed.
Make sure the headlights, brake light and taillight are working properly.
If you are carrying cargo, also check the following:
Loading Limits Make sure you do not exceed the load limits
Check that all cargo is secure.
Cargo
Check these items after you get on the ATV:
Throttle Check the freeplay and adjust if needed.
Press the throttle to make sure it moves smoothly without sticking, and snaps shut automatically when it is released, in all
steering positions (page 154).
Brakes Squeeze the front and rear brake levers and step on the rear brake pedal to check that the controls operate normally. Depress the rear brake pedal several times, then check for proper rear brake lever/parking brake
lever freeplay (pages 171). Make sure there
is no brake fluid leakage.
Reverse Assist Lever Check the freeplay and adjust if needed
(page 157). Make sure the lever operates
smoothly without sticking.
(cont’d)
Before Riding
63
Is Your ATV Ready to Ride?
Headlight and
Headlight Dimmer
Switch
Check for proper function (page 41).
Engine Stop Switch
Check for proper function (page 40).
Steering Check that the wheels turn properly as you steer the handlebar. Move the handlebar right and left and check that there is no excessive backlash.
Remember, be sure to take care of any problem you find, or have your dealer correct it before you ride.
64
Before Riding
Load Limits & Guidelines
Your Honda was designed as a rider-only ATV. It was not designed to carry a passenger. It can carry cargo on the cargo racks, however, carrying cargo anywhere else or carrying a passenger could interfere with your balance and control of the ATV.
In addition, exceeding the weight limits or carrying an unbalanced load can seriously affect your ATV’s handling, braking and stability.
Adding accessories or making modifications that change this ATV’s design and performance can also make it unsafe. Also, the weight of any accessories will reduce the maximum load the ATV can carry.
More specific information on load limits, accessories, and modifications follows.
Loading
How much weight you put on your ATV, and how you load it, are important to your safety. If you decide to carry cargo, you should be aware of the following information.
WARNING 3 WARNING
Overloading, improper loading, or carrying a passenger can cause a crash and you can be seriously hurt or killed.
Follow all load limits and other loading guidelines in this manual.
Before Riding
65
Load Limits & Guidelines
Load Limits
Following are the load limits for your ATV:
There are limits to how much weight can be carried on your ATV and be pulled in a trailer.
The following load limits apply to standard equipment only.
Modifying your ATV, using non-standard equipment, or riding on terrain that is not flat and smooth could further reduce these limits.
maximum weight capacity
(includes the weight of the rider, all cargo, and accessories.)
573 lb (260 kg) front cargo rack weight limit rear cargo rack weight limit
= 99 lb (45 kg)
= 187 lb (85 kg) tow weight limit
(Combined weight of the trailer
= 1322 lb (600 kg) and all cargo in the trailer) tongue weight = 30 lb (14 kg) recommended
(Weight on the trailer tongue) tongue and rear cargo weight = 187 lb (85 kg) maximum
(Combined weight on the trailer tongue and on the rear cargo rack)
Tongue weight can be measured with an ordinary bathroom scale.
Place the scale under the tongue, using either a tongue jack or other support to keep the trailer level.
The weight of added accessories will reduce the maximum cargo weight you can carry.
66
Before Riding
Load Limits & Guidelines
Loading Guidelines
Carrying cargo or pulling a trailer will affect how your ATV handles and greatly reduce its ability in accelerating, braking and making turns and other maneuvers.
Be sure to observe the weight limits and follow these guidelines:
• Check that the tires are properly inflated.
• Do not place cargo anywhere on the ATV other than on the front and rear racks. Otherwise, operating stability may be adversely affected.
• Never ride with a passenger on the front or rear cargo racks. The
ATV is not designed to carry a passenger.
• Use the trailer hitch to tow another vehicle or trailer. Do not tow by tying a rope or cable to the rear rack.
• Load cargo on the rear rack as far forward as possible. Make sure cargo on the front rack does not interfere with handlebar movement.
• Do not allow cargo to extend beyond the edges of either the front or rear racks.
• Make sure all cargo is secured before riding.
• Balance cargo weight evenly on both sides.
• Never exceed the maximum weight limit.
• When towing a trailer, take care to maintain balance and stability. Distribute cargo between the front and rear of the trailer to obtain the recommended tongue weight.
• Allow extra room for starting, stopping and turning whenever you carry cargo or pull a trailer.
• Avoid riding on steep slopes when carrying cargo or pulling a trailer.
• Never cross a slope when towing a trailer.
Before Riding
67
Accessories & Modifications
Modifying your ATV or using non-Honda accessories can make your
ATV unsafe.
Before you consider making any modifications or adding an accessory, be sure to read the following information.
WARNING 3 WARNING
Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding accessories and modifications.
Accessories
We strongly recommend that you use only Honda Genuine or Honda
Signature Accessories that have been specifically designed and tested for your ATV. Because Honda cannot test all other accessories, you must be personally responsible for proper selection, installation, and use of non-Honda accessories.
Check with your dealer for assistance and always follow these guidelines:
• Make sure the accessory does not obscure any lights, reduce ground clearance, limit suspension travel or steering travel, or interfere with operating any controls.
• Make sure the accessory does not interfere with your ability to shift body position on the seat or operate hand and foot controls.
• Do not add any electrical equipment that will exceed the vehicle’s
electrical system capacity (page 231). A blown fuse can cause a
loss of lights or engine power (page 215).
68
Before Riding
Accessories & Modifications
Modifications
We strongly advise you not to remove any original equipment or modify your ATV in any way that would change its design or operation. Such changes could seriously impair your ATV’s handling, stability, and braking, making it unsafe to ride.
We also advise you not to make any modifications or remove any equipment (such as the USDA qualified spark arrester or emission control system components) that would make your ATV illegal in your area.
Removing or modifying your lights, exhaust system, emission control system, or other equipment can also make your ATV illegal.
Before Riding
69
70
Before Riding
BLANK PAGE
Basic Operation & Riding
Basic Operation & Riding This section gives basic riding instructions, including how to start and stop your engine, and how to use the throttle and brakes. It also provides important information on riding with cargo.
To protect your new engine and enjoy optimum performance and
service life, refer to Break-in Guidelines (page 233).
Safe Riding Precautions .............................................................. 73
Off-road Use Only.................................................................... 73
Keep Hands and Feet on Controls............................................ 74
Control Speed ......................................................................... 75
Use Care on Unfamiliar or Rough Terrain ................................. 76
Do Not Perform Stunts............................................................. 77
Starting & Stopping the Engine................................................... 78
Preparation.............................................................................. 79
Starting Procedure ................................................................... 80
Flooded Engine........................................................................ 81
Bank Angle Sensor Ignition Cut-off System .............................. 81
Stalled Engine.......................................................................... 82
How to Stop the Engine........................................................... 83
Using the Recoil Starter (Canada only) ..................................... 84
Shifting Gears............................................................................. 85
Riding in Reverse ........................................................................ 87
(cont’d)
Basic Operation & Riding
71
Basic Operation & Riding
Braking....................................................................................... 89
Riding Your ATV ......................................................................... 91
Making Turns .......................................................................... 91
Skidding or Sliding................................................................... 93
Riding Up Hills ......................................................................... 94
Riding Down Hills .................................................................... 98
Crossing or Turning on Hills or Slopes ...................................... 99
Riding Over Obstacles ............................................................ 101
Riding Through Water ........................................................... 102
Parking ..................................................................................... 104
72
Basic Operation & Riding
Safe Riding Precautions
Before riding your ATV for the first time, please review the ATV
Safety
section beginning on page 1, and the
Before Riding section
Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.
Off-road Use Only
Your ATV and its tires are designed and manufactured for off-road use only, not for pavement. Riding on pavement can affect handling and control. You should not ride your ATV on pavement.
WARNING 3 WARNING
Operating this ATV on paved surfaces may seriously affect handling and control of the
ATV, and may cause the vehicle to go out of control.
Never operate the ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets.
When riding off-road, also remember to always obey local off-road riding laws and regulations. Obtain permission to ride on private property. Avoid posted areas and obey “no trespassing” signs.
(cont’d)
Basic Operation & Riding
73
Safe Riding Precautions
You should never ride your ATV on public streets, roads or highways, even if they are not paved. Drivers of street vehicles may have difficulty seeing and avoiding you, which could lead to a collision. In many states it is illegal to operate ATVs on public streets, roads and highways.
WARNING 3 WARNING
Operating this ATV on public streets, roads or highways could cause you to collide with another vehicle.
Never operate this ATV on any public street, road or highway, even a dirt or gravel one.
Keep Hands and Feet on Controls
Always keep both hands on the handlebars and both feet on the footpegs when riding your ATV. This is important to maintain your balance and to control the vehicle. Removing even one hand from the handlebars or one foot from the footpegs can reduce your ability to control the ATV or could cause you to lose your balance and fall off the ATV.
WARNING 3 WARNING
Removing hands from handlebars or feet from footpegs during operation can reduce your ability to control the ATV or could cause you to lose your balance and fall off of the
ATV.
Always keep both hands on the handlebars and both feet on the footpegs of your ATV during operation.
74
Basic Operation & Riding
Safe Riding Precautions
Control Speed
Riding at excessive speed increases the chance of a crash. In choosing a proper speed, you need to consider the capability of your vehicle, the terrain, visibility and other operating conditions, plus your own skills and experience.
WARNING 3 WARNING
Operating this ATV at excessive speeds increases your chances of losing control of the
ATV, which can result in a crash.
Always go at a speed that is proper for your vehicle, the terrain, visibility and other operating conditions, and your experience.
Basic Operation & Riding
75
Safe Riding Precautions
Use Care on Unfamiliar or Rough Terrain
Before riding in a new area, always check the terrain thoroughly.
Don’t ride fast on unfamiliar terrain or when visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or holes in time to react.)
WARNING 3 WARNING
Failure to use extra care when operating this
ATV on unfamiliar terrain could result in the
ATV overturning or going out of control.
Go slowly and be extra careful when operating on unfamiliar terrain. Always be alert to changing terrain conditions when operating the ATV.
76
Basic Operation & Riding
Safe Riding Precautions
Never ride past the limit of visibility. Maintain a safe distance between your ATV and other off-road vehicles. Always exercise caution, and use extra care on rough, slippery and loose terrain.
WARNING 3 WARNING
Failure to use extra care when operating on excessively rough, slippery or loose terrain could cause loss of traction or vehicle control, which could result in a crash, including an overturn.
Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control the
ATV on such terrain. Always be especially cautious on these kinds of terrain.
Do Not Perform Stunts
You should always operate your ATV in a safe and reasonable manner. When riding, always keep all four wheels on the ground.
WARNING 3 WARNING
Attempting wheelies, jumps, and other stunts increases the chance of a crash, including an overturn.
Never attempt stunts, such as wheelies or jumps. Don’t try to show off.
Basic Operation & Riding
77
Starting & Stopping the Engine
Always follow the proper starting procedure described below.
For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your ATV’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death.
WARNING 3 WARNING
Running the engine of your vehicle while in an enclosed or even partially enclosed area can cause a rapid build-up of toxic carbon monoxide gas.
Breathing this colourless, odorless gas can quickly cause unconsciousness and lead to death.
Only run your vehicle's engine when it is located in a well ventilated area outdoors.
78
Basic Operation & Riding
Starting & Stopping the Engine
Preparation
(2)
(1)
(1) ignition switch
(2) neutral indicator
(3)
(3) engine stop switch
1. Before starting, make sure the vehicle is on a level surface and
lock the parking brake (page 45).
2. Turn the ignition switch (1) to ON ( q ).
Confirm the following:
• The transmission is in neutral, the neutral indicator (2) is ON and the gear position indicator shows “N”.
• The engine stop switch (3) is set to RUN ( e ).
Basic Operation & Riding
79
Starting & Stopping the Engine
Starting Procedure
This ATV is fuel-injected with an automatic choke.
Follow the procedure indicated below.
Any Air Temperature
• Press the start/over ride button with the throttle completely closed.
The engine will not start if the throttle is fully open (because the electronic control module cuts off the fuel supply).
Snapping the throttle or fast idling for more than 5 minutes may cause exhaust pipe and muffler discolorations.
80
Basic Operation & Riding
Starting & Stopping the Engine
Flooded Engine
If the engine fails to start after repeated attempts, it may be flooded with excess fuel. To clear a flooded engine:
1. Leave the engine stop switch set to RUN ( e ).
2. Open the throttle fully.
3. (USA)
Press the start/over ride button for 5 seconds.
(Canada)
Press the start/over ride button for 5 seconds (or operate the recoil starter several times).
4. Follow the normal starting procedure.
5. If the engine starts, then open the throttle slightly if idling is unstable.
If the engine does not start, wait 10 seconds, then follow steps
1 – 4 again.
If the engine still won’t start, refer to If Your Engine Quits or Won’t
Start
Bank Angle Sensor Ignition Cut-off System
Your vehicle’s banking (lean angle) sensor system is designed to automatically stop the engine if the vehicle is overturned.
Before restarting the engine, you must turn the ignition switch to the
OFF ( w ) position and then back to ON ( q ). The engine will not restart until you perform this procedure.
Basic Operation & Riding
81
Starting & Stopping the Engine
Stalled Engine
You can restart the engine while the vehicle is stopped by squeezing the front brake lever and pressing the start/over ride button.
Do not press the throttle lever while starting in gear. The engine will not start if the throttle is fully open (because the electronic control module cuts off the fuel supply).
Once you have started the engine, release the front brake lever, then apply throttle gradually.
82
Basic Operation & Riding
Starting & Stopping the Engine
How to Stop the Engine
Normal Engine Stop
To stop the engine, make sure the transmission is in neutral by checking that the neutral indicator light is on, then turn the ignition switch to OFF ( w ).
The engine stop switch should normally remain in the RUN ( e ) position even when the engine is OFF.
If your ATV is stopped with the engine stop switch OFF ( r ) and the ignition switch ON ( q ), the battery will discharge.
Emergency Engine Stop
To stop the engine in an emergency, use the engine stop switch. To operate, slide the switch to either OFF ( r ) position.
Basic Operation & Riding
83
Starting & Stopping the Engine
Using the Recoil Starter (Canada only)
The recoil starter is used to start the engine when the battery is low.
To operate the recoil starter:
1. Turn the ignition switch to ON and engine stop switch to RUN.
2. Check that the transmission is in neutral.
3. Grasp the starter grip (1) firmly, then pull it out slowly approximately 4 in (100 mm).
4. Pull the grip up briskly and fully.
5. After the engine starts, allow the starter grip to return slowly.
Pull the recoil starter grip straight out so that the cord does not touch the side cover. Repeated contact with the side cover can damage the starter cord.
If the starter grip does not return smoothly (because of dirt in the assembly), see your dealer.
RIGHT SIDE
(1)
(1) starter grip
84
Basic Operation & Riding
UPSHIFTING SEQUENCE
DOWNSHIFTING SEQUENCE
Shifting Gears
Your ATV has five forward gears: 1, 2, 3, 4, and 5.
The shift lever is located near the left footpeg. One full stroke of the shift lever shifts the transmission to the next higher or lower gear in the shifting sequence. The shift lever automatically returns to the horizontal position when released.
To upshift to a higher gear, put the toe of your boot under the shift lever and raise it one full stroke. To downshift, step on the shift lever and depress it one full stroke.
To select reverse, see Riding in Reverse
After starting the engine and letting it warm up, follow this procedure:
1. With the transmission in neutral, release the parking brake, but continue squeezing the rear brake lever/parking brake lever.
Basic Operation & Riding
85
Shifting Gears
2. With the throttle closed, raise the shift lever one full stroke to shift into 1st (first) gear.
3. Release the rear brake lever/parking brake lever and increase engine speed by gradually opening the throttle.
4. When speed increases, release the throttle and shift to 2nd gear by raising the shift lever one full stroke.
5. Repeat this sequence to progressively upshift to 3rd, 4th and 5th
(top) gear.
6. To downshift, reverse this sequence. Remember to close the throttle each time you shift to the next lower gear.
Learning when to shift gears comes with experience. Keep the following tips in mind:
• As a general rule, shift while moving in a straight line.
• Close the throttle (release) completely before shifting. Improper shifting may damage the engine, transmission, and drivetrain.
• Upshift to a higher gear or reduce throttle before engine rpm
(speed) gets too high. Learn the relationship between engine sound and the normal shifting points.
• Downshift to a lower gear before you feel the engine laboring
(lugging) at low rpm.
• Avoid downshifting to help slow your ATV when engine rpm is high. Downshifting when engine speed is near its allowable maximum may over-rev the engine and possibly cause damage.
• To prevent transmission damage, do not coast or tow the ATV for long distances with the engine off.
Recommended Shift Points
Ride in the highest gear that lets the engine run and accelerate smoothly.
This will give you good fuel economy and effective emissions control.
86
Basic Operation & Riding
Riding in Reverse
If you need to ride in reverse, make sure the area behind you is clear and only operate the ATV at low speed.
WARNING 3 WARNING
Improperly operating in reverse could cause you to hit an obstacle or person behind you, resulting in serious injury.
Make sure there are no obstacles or people behind you before selecting reverse gear.
When it is safe to proceed, go slowly.
1. Bring the vehicle to a complete stop, then make sure the transmission is in neutral.
2. Be sure there are no obstacles or people in the way.
3. Fully rotate the P/R lever (1) counterclockwise to engage the P/R lever with the reverse assist lever (2).
4. While continuing to hold the P/R lever, squeeze the rear brake lever/parking brake lever (3), then depress the shift lever once to shift into “R” (reverse) gear.
5. Make sure that the reverse indicator comes on and the gear position indicator shows “R”.
LEFT HANDLEBAR
(1)
(2)
(3)
(1) P/R lever
(2) reverse assist lever
(3) rear brake lever/parking brake lever
Basic Operation & Riding
87
Riding in Reverse
NOTICE
Your ATV may be equipped with a reverse speed limiter, which helps the vehicle to maintain a safe speed while riding in reverse gear.
6. Release the rear brake lever/parking brake lever.
7. Open the throttle gradually and ride slowly. Do not open the throttle suddenly or make abrupt turns.
8. To stop, close the throttle and gradually apply both the front and rear brakes. Do not abruptly apply the rear brake by alone.
9. To shift out of reverse and into neutral, raise the shift lever one stroke to shift into “N” (neutral) gear.
(the neutral indicator is on and the gear position indicator shows
“N”)
WARNING 3 WARNING
Applying only the rear brake abruptly when operating in reverse gear could cause the front wheels to lift off the ground and the
ATV could overturn backwards.
Carefully apply both the front and rear brakes when stopping in reverse gear.
88
Basic Operation & Riding
Braking
Your ATV is equipped with disc brakes on both front wheels which are hydraulically activated by operating the right brake lever. The single disc brake of the rear drivetrain is hydraulically activated by pressing down on the brake pedal and mechanically activated by operating the left brake lever.
Although the front and rear brakes have separate controls, all four wheels are interconnected when your ATV is in the 4WD mode. So operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.
As a general rule, the front braking system provides about 70 percent of total stopping power.
For full braking effectiveness, use both the pedal and lever simultaneously. Using both braking systems will stop your ATV faster with greater stability.
To slow or stop, apply the brake lever and brake pedal smoothly, while downshifting to match your speed.
Gradually increase braking as you feel the brakes slowing your speed. The increase in engine compression from downshifting will help slow your ATV.
Applying the brakes too hard may cause the wheels to lock and slide, reducing control of your ATV. If this happens, release the brake controls, steer straight ahead until you regain control, then reapply the brakes more gently.
Basic Operation & Riding
89
Braking
When possible, reduce your speed or complete braking before entering a turn. Avoid braking or closing the throttle quickly while turning. Either action may cause one or more wheels to slip and reduce your control of your ATV.
Your ability to brake in a turn and to brake hard in an emergency situation are important riding skills.
When descending a long, steep grade, use engine compression braking by downshifting, with intermittent use of both brakes.
Continuous brake application can overheat the brakes and reduce their effectiveness.
Riding with your foot resting on the brake pedal or your hands on the brake levers may overheat the brakes, reducing effectiveness.
For information on how to apply the brakes in various riding situations, see the following section,
90
Basic Operation & Riding
Riding Your ATV
Making Turns
Learn how to turn your ATV properly. Practice the techniques outlined in this section on level ground and at low speeds until you are confident in making turns.
WARNING 3 WARNING
Turning improperly can make the ATV go out of control, causing a collision or overturn.
• Always follow proper procedures for turning as described in this owner’s manual.
• Practice turning at low speeds before attempting to turn at faster speeds.
• Do not turn at excessive speeds.
Remember that steering the handlebar in the front differential lock mode will cause steering to be heavy and increase turning radius.
Basic Operation & Riding
91
Riding Your ATV
Lean your body to the inside of a turn and forward.
To make a turn on level ground: Steer the handlebar and lean your body toward the inside of the turn. Leaning helps balance the vehicle, and it feels more comfortable. Leaning into a turn is an important technique to master in riding an ATV.
To make a sharp turn at low speed: It helps to shift your body slightly forward on the seat, and lean inside, as you steer the handlebar.
Shifting weight forward allows the rear wheels to turn easier, and it also improves front-wheel steering.
To make a turn from a full stop: Apply the throttle gradually when you turn and start at the same time. Remember to shift your body forward to make sharp low-speed turns and whenever you turn while accelerating from a full stop.
92
Basic Operation & Riding
Riding Your ATV
Skidding or Sliding
The terrain surface can be a major factor affecting turns. Skidding during a turn is more likely to occur on slippery surfaces, such as snow, ice, mud and loose gravel. If you skid on ice, you may lose all directional control. To avoid skidding on slippery terrain, keep your speed low and ride with caution.
WARNING 3 WARNING
Skidding or sliding improperly may cause you to lose control of this ATV. You may also regain traction unexpectedly, which may cause the ATV to overturn.
Learn to safely control skidding by practicing at low speeds and on level, smooth terrain.
If your ATV skids sideways during a turn, steer in the direction of the skid. Avoid hard braking or accelerating until you have regained directional control.
Remember that steering the handlebar in the front differential lock mode will cause steering to be heavy and increase turning radius.
(cont’d)
Basic Operation & Riding
93
Riding Your ATV
Riding Up Hills
The ATV’s ability to safely climb hills largely depends on the rider’s skill and judgment. Begin by practicing on smooth, gentle slopes. As you gain experience, you’ll learn the hazards and your own limitations. You may then proceed to ride on more difficult terrain.
However, you must be able to decide which hills or hazards might cause the ATV to overturn. Avoid excessively steep hills.
WARNING 3 WARNING
Operating on excessively steep hills can cause the vehicle to overturn more easily than operating on level surfaces or small hills.
Never operate the ATV on hills too steep for the ATV or for your abilities.
When climbing hills, you must shift weight toward the front wheels to help keep them on the ground. To do this, shift your body slightly forward on the seat and lean forward. For greater weight shift, move your body farther forward and lean forward.
WARNING 3 WARNING
Climbing hills improperly could cause loss of control or cause the ATV to overturn.
Always follow proper procedures for climbing hills as described in this owner’s manual.
94
Basic Operation & Riding
Riding Your ATV
Shift weight forward when climbing hills.
• Always check the terrain carefully before you start up any hill.
• Never climb hills with excessively slippery or loose surfaces.
• To climb a hill, take a running start in an appropriate gear and speed for the conditions. Maintain a steady speed as you ascend the hill.
• Never open the throttle suddenly or make sudden gear changes.
The ATV could flip over backward.
• Never go over the top of any hill at high speed. An obstacle, a sharp drop, or another vehicle or person could be on the other side of the hill.
Basic Operation & Riding
95
Riding Your ATV
Stalling the ATV and/or Rolling Backwards:
If you incorrectly estimate climbing capability or terrain conditions, the ATV may not have enough power or traction to continue uphill.
If this happens, the ATV can stall and/or roll backwards.
WARNING 3 WARNING
Stalling, rolling backwards or improperly dismounting while climbing a hill could result in the ATV overturning.
Always follow proper procedures for climbing a hill as described in this owner’s manual.
What to do if the ATV stalls or rolls backwards when climbing a hill:
If you are about to lose all forward speed:
1. Using the front and rear brakes together, bring the ATV to a stop with the vehicle pointed straight uphill.
2. Get off the ATV while you continue holding the brakes.
3. Shift into neutral, set the parking brake and turn the engine off.
4. Then assess the situation.
If the ATV starts rolling backwards before you begin braking:
1. Keep your weight uphill.
2. Carefully apply the front brakes first, then carefully apply the rear brake. Do not apply either brake abruptly if you are rolling backwards, or the vehicle may overturn.
If the ATV continues sliding backwards:
After you’ve applied the brakes, get off and away from the vehicle.
Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.
96
Basic Operation & Riding
Riding Your ATV
What to do after the ATV has stalled or rolled backwards:
If the hill is too steep or too slippery, or if you have any doubt whether you can safely walk the ATV back down the hill, leave the vehicle where it is and get help. If possible, block the wheels so the vehicle doesn’t roll backwards.
If the hill is not too steep and you have good footing, you may be able to walk the ATV back down the hill. Make sure your intended path is clear in case you lose control of the ATV.
Be sure your legs are clear of the wheels.
Body position for backing down a hill.
1. Stand with your body facing downhill, beside the vehicle so you can reach the rear brake lever/parking brake lever with your right hand.
2. Be sure your legs are clear of the wheels.
Check your footing.
3. Slowly and carefully back the ATV down the hill using the rear brake lever/parking brake lever to control speed.
4. If you lose control of the ATV, for your safety, get away from the vehicle.
(cont’d)
Basic Operation & Riding
97
Riding Your ATV
Riding Down Hills
It’s usually advisable to descend hills with the ATV pointed straight downhill. Avoid angles that would cause the vehicle to lean sharply to one side.
WARNING 3 WARNING
Going down a hill improperly could cause loss of control or cause the ATV to overturn.
Always follow proper procedures for going down hills as described in this owner’s manual.
On downhills, shift your weight back.
As you approach a downhill, stop and survey the terrain below.
Never ride past the limit of your visibility. Never go down a hill at high speed.
98
Basic Operation & Riding
Riding Your ATV
When you’ve selected a safe downhill path, shift into a lower gear, shift your weight back with your arms extended and braced against the handlebar, then go down slowly with the throttle closed.
Use mainly the rear brake to control speed. Avoid using either the front brake or rear brake hard or abruptly when riding down hills.
Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.
Remember, braking effectiveness is reduced on any hill with a loose surface.
Crossing or Turning on Hills or Slopes
Riding on hills or slopes is different from riding on level terrain. Be careful when riding on any hill. Make sure that you practice on gentle, smooth slopes before attempting to ride on steeper or more difficult terrain.
WARNING 3 WARNING
Improperly crossing hills or turning on hills could cause loss of control or cause the ATV to overturn.
Always follow proper procedures for crossing or turning on slopes as described in this owner’s manual. Avoid crossing steep hills if possible.
Remember that steering the handlebar in the front differential lock mode will cause steering to be heavy and increase turning radius.
Basic Operation & Riding
99
Riding Your ATV
Crossing Hills or Slopes
• To maintain balance and stability when riding across a slope, you need to shift weight toward the uphill side of the vehicle. To do this, move your body off the center of the seat and lean toward the uphill side.
• On a slippery or loose surface, you may also need to steer slightly uphill to maintain a straight course across the slope.
• Avoid crossing hills that are excessively steep, slippery or rough.
Shift weight uphill when crossing slopes.
Making Turns on Slopes
• Compared to riding on level ground, you may need to shift more weight and lean more when making turns on slopes.
• Do not make turns on any slopes until you have first mastered the techniques for making turns on level terrain.
100
Basic Operation & Riding
Riding Your ATV
Riding Over Obstacles
Before operating in a new area, check for obstacles. Watch out for bumps, rain ruts, potholes and other obstacles in the terrain. When you approach any obstacle, reduce your speed and be prepared to stop.
Never try to ride over large obstacles, such as large rocks or fallen logs.
WARNING 3 WARNING
Improperly operating over obstacles could cause loss of control or a collision and could cause the ATV to overturn.
When you go over obstacles, always follow proper procedures as described in this owner’s manual.
(cont’d)
Basic Operation & Riding
101
Riding Your ATV
Riding Through Water
Your ATV is designed to travel through water up to approximately
10 inches (254 mm) deep. Before crossing a stream, make sure the water is not too deep or flowing too fast.
WARNING 3 WARNING
The ATV tires have some ability to float.
Operating this ATV through deep or fastflowing water may cause a loss of traction and loss of control, which could lead to a crash.
Never operate this ATV in fast-flowing water or in water deeper than that specified in this owner’s manual.
NOTICE
Water entering the muffler may damage the oxygen sensor and result in emissions control system malfunction. Have your ATV dealer inspect the oxygen sensor immediately after water enters the muffler.
102
Basic Operation & Riding
Riding Your ATV
1. Choose a path where both banks have gradual slopes.
2. Proceed through the water at a slow, steady speed.
3. Watch out for submerged obstacles and slippery rocks.
4. Avoid getting the spark plug or air cleaner wet, as this would cause the engine to stop.
5. After leaving the water, always test both the front and rear brakes.
• Riding through water can make the brakes less effective than normal, and may reduce stopping ability.
• If necessary, apply the brakes repeatedly until they dry out and operate normally.
Basic Operation & Riding
103
Parking
1. Look for level parking area. Make sure the ground surface is firm.
2. After bringing your ATV to a stop, hold the brakes while you shift into neutral.
3. Set the parking brake (page 46).
4. Turn the ignition switch to OFF ( w ).
If it is necessary to start the engine when your ATV in gear and is stopped on a grade, rock the vehicle back and forth to allow shifting the transmission into neutral.
The brake light is activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch to OFF
( w ) to avoid discharging the battery.
Parking on a Steep Incline or a Loose or Slippery Surface
If you must park your ATV on a steep incline or loose or slippery surface, use the following procedure:
1. While holding the brakes, set the parking brake.
2. Turn the ignition switch to OFF ( w ) and release the brakes.
3. If the ATV begins to move, either while sitting on it or after you dismount, find a better parking location.
4. If rocks or other objects are available, you can block the wheels as shown for additional security.
104
Basic Operation & Riding
Servicing Your Honda
Servicing Your Honda To help keep your ATV in good shape, this section includes a
Maintenance Schedule for required service and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on fuels and oils, and tips for keeping your Honda looking good.
For information about replacing fuses, see page 215.
For information about the exhaust emission and noise requirements of the U.S. Environmental Protection Agency (EPA), the California Air
Resources Board (CARB), and Environment Climate Change Canada
USA only
Maintenance, replacement or repair of the emission control devices and systems may be performed by any ATV repair establishment or individual using parts that are “certified” to
EPA standards.
Before You Service Your Honda
The Importance of Maintenance ............................................... 107
Maintenance Safety .................................................................. 108
Important Safety Precautions ................................................. 109
Maintenance Schedule ............................................................. 110
Maintenance Record................................................................. 114
Service Preparations
Maintenance Component Locations ......................................... 115
Tool Kit .................................................................................... 118
Owner’s Manual Storage .......................................................... 119
Seat Removal............................................................................ 120
Rear Fender Cover Removal ...................................................... 121
Tank Cover Assembly Removal ................................................. 122
(cont’d)
Servicing Your Honda
105
Servicing Your Honda
Clip Removal ............................................................................ 123
Service Procedures
Fluids & Filters
Fuel .......................................................................................... 124
Engine Oil & Filter ..................................................................... 127
Rear Final Gear Oil .................................................................... 136
Front Final Gear Oil................................................................... 138
Coolant .................................................................................... 140
Air Cleaner ............................................................................... 148
Engine
Throttle .................................................................................... 154
Clutch System .......................................................................... 156
Reverse Inhibitor System ........................................................... 157
Spark Plug ................................................................................ 158
Valves....................................................................................... 161
Spark Arrester .......................................................................... 162
Chassis
Suspension ............................................................................... 163
Brakes ...................................................................................... 166
Tires ......................................................................................... 174
Guards ..................................................................................... 181
Drivetrain Boots ........................................................................ 182
Electrical
Battery ..................................................................................... 183
Appearance Care...................................................................... 188
106
Servicing Your Honda
Before You Service Your Honda
The Importance of Maintenance
A well-maintained ATV is essential for safe, economical, and troublefree riding. It will also help reduce air pollution. Careful preride inspections and good maintenance are especially important because your ATV is designed to be ridden over rough off-road terrain.
To help you properly care for your ATV, this section of the manual provides a Maintenance Schedule. The service intervals in this schedule are based on average riding conditions.
WARNING 3 WARNING
Improperly maintaining this ATV or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed.
Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.
Frequent servicing of the air cleaner is especially important to help you avoid a possible costly engine repair.
If your ATV overturns or is involved in a crash, be sure your dealer inspects all major parts, even if you are able to make some repairs.
Servicing Your Honda
107
Maintenance Safety
This section includes instructions on how to perform some important maintenance tasks. If you have basic mechanical skills, you can perform many of these tasks with the tools provided with your ATV.
Other tasks that are more difficult and require special tools are best performed by professionals. Removing the wheels should normally be handled only by a Honda technician or other qualified mechanic.
Instructions are included in this manual only to assist in emergency service.
Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
WARNING 3 WARNING
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this owner’s manual.
108
Servicing Your Honda
Maintenance Safety
Important Safety Precautions
• Make sure the engine is off before you begin any maintenance or repairs. This will help eliminate several potential hazards:
Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate the engine.
Burns from hot ATV parts.
Let the engine and exhaust system cool before touching.
Injury from moving parts. Do not run the engine unless instructed to do so.
• Read the instructions before you begin, and make sure you have the tools and skills required.
• To reduce the possibility of a fire or explosion, be careful when working around gasoline. Use only non-flammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from all fuel-related parts.
Remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new Honda Genuine Parts or other equivalents for repair and replacement. If you have the tools and skills required for additional maintenance jobs, you can purchase an official Honda
Servicing Your Honda
109
Maintenance Schedule
The required Maintenance Schedule that follows specifies how often you should have your ATV serviced, and what things need attention.
It is essential to have your ATV serviced as scheduled to maintain safe, dependable performance and proper emission control.
The service intervals in this Maintenance Schedule are based on average riding conditions. Some items will need more frequent service if you ride in unusually wet or dusty areas or at full throttle.
Consult your dealer for recommendations applicable to your individual needs and use.
Some items in the Maintenance Schedule can be performed with basic mechanical skills and hand tools. Procedures for these items are provided in this manual. Other items involve more extensive procedures and may require special training, tools, and equipment.
We recommend that you have your dealer perform these tasks unless you have advanced mechanical skills and the required tools and equipment. Procedures for such items in this schedule are provided in an official Honda Service Manual available for purchase
If you do not feel capable of performing a given task or need assistance, remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. If you decide to do your own maintenance, use only Honda Genuine Parts or their equivalents for repair or replacement to ensure the best quality and reliability.
110
Servicing Your Honda
Maintenance Schedule
Perform the pre-ride inspection (page 61) and owner maintenance
on this section at each scheduled maintenance period.
Each item on the maintenance schedule requires some mechanical knowledge. Certain items (particularly those marked * and ** ) may require more technical information and tools. Consult your dealer.
* Should be serviced by your dealer, unless the owner has proper tools and service data and is mechanically qualified. Refer to the
official Honda Service Manual (page 242).
** In the interest of safety, we recommend these items be serviced only by your dealer.
Summary of Maintenance Schedule Notes & Procedures:
NOTES:
1. Service more frequently when riding in dusty areas, sand or snow.
2. Service more frequently after riding in very wet or muddy conditions.
3. Replace every 2 years. Replacement requires mechanical skill.
Servicing Your Honda
111
Maintenance Schedule
Maintenance Procedures:
I: inspect and clean, adjust, lubricate, or replace, if necessary
C: clean
A: adjust
L: lubricate
R: replace
FREQUENCY WHICHEVER
COMES FIRST mi km
MONTH
NOTE HOURS ITEMS
*
*
FUEL LINE
THROTTLE OPERATION
*
AIR CLEANER
AIR CLEANER HOUSING
DRAIN TUBE
SPARK PLUG
VALVE CLEARANCE
ENGINE OIL
NOTE 1
NOTE 2
*
*
ENGINE OIL FILTER
ENGINE IDLE SPEED
RADIATOR COOLANT
COOLING SYSTEM
NOTE 3
NOTE 2
INITIAL
MAINT.
100
150
1
20
REGULAR
MAINT. INTERVAL
600
1000
6
100
C
I
1200
2000
12
200
I
I
C
I
I
I
I
I
I
INITIAL=
100 mi (150 km), 20 operating hours or 1 month: R
REGULAR=
Every 600 mi (1,000 km),
100 operating hours or 12 months: R
I I I
I
I
I
I
Refer to page
—
—
—
* Should be serviced by your dealer, unless the owner has proper tools and service data and is
mechanically qualified. Refer to the official Honda Service Manual (page 242).
112
Servicing Your Honda
Maintenance Schedule
*
*
*
*
**
**
*
*
*
ITEMS
*
**
**
FREQUENCY WHICHEVER
COMES FIRST mi km
MONTH
NOTE HOURS
DRIVETRAIN BOOTS
FRONT/REAR FINAL GEAR
OIL
BRAKE FLUID
BRAKE PADS WEAR
BRAKE LIGHT SWITCH
BRAKE SYSTEM
REVERSE INHIBITOR
SYSTEM
GUARDS
CLUTCH SYSTEM
SUSPENSION
SPARK ARRESTER
NUTS, BOLTS, FASTENERS
WHEELS/TIRES
TIE-ROD AND JOINT
BOOTS
STEERING SHAFT HOLDER
BEARINGS
STEERING SYSTEM
NOTE 3
NOTE 1, 2
INITIAL
MAINT.
100
150
1
20
I
I
I
REGULAR
MAINT. INTERVAL
600
1000
6
100
I
(R: EVERY
2 YEARS)
I
I
I
I
I
I
I
I
I
1200
2000
12
200
I
I
I
I
I
I I
I
I
C
I
I
I
I
I
C
I
I
I
I
I
Refer to page
—
—
—
—
* Should be serviced by your dealer, unless the owner has proper tools and service data and is
mechanically qualified. Refer to the official Honda Service Manual (page 242).
** In the interest of safety, we recommend these items be serviced only by your dealer.
Servicing Your Honda
113
Maintenance Record
Keeping an accurate maintenance record will help ensure that your
ATV is properly maintained. Retain detailed receipts to verify the maintenance was performed. If the ATV is sold, these receipts should be transferred with the ATV to the new owner. Make sure whoever performs the maintenance completes this record. All scheduled maintenance, including the 100 mile (150 km) or 1 month or
20 hours initial maintenance, is considered a normal owner operating cost and will be charged for by your dealer. Use the space under
Notes to record anything you want to remind yourself about or mention to your dealer.
Date Miles (km) or months or hours
100 (150) or
1 or 20
600 (1,000) or
6 or 100
1,200 (2,000) or
12 or 200
1,800 (3,000) or
18 or 300
2,400 (4,000) or
24 or 400
3,000 (5,000) or
30 or 500
3,600 (6,000) or
36 or 600
4,200 (7,000) or
42 or 700
4,800 (8,000) or
48 or 800
ODO or
HOUR
Performed
By:
Notes
114
Servicing Your Honda
Service Preparations
Maintenance Component
Locations
P/R lever reverse assist lever front brake fluid reservoir front brake lever rear brake lever/ parking brake lever throttle lever
Servicing Your Honda
115
Maintenance Component
Locations battery fuse box main fuse 1 main fuse 2
PS fuse rear brake fluid reservoir rear brake light switch front suspension spring pre-load adjusters coolant reserve tank fuel fill cap rear brake caliper rear brake pedal engine oil filter front brake calipers rear brake lever/parking brake lever adjuster front final gear oil fill cap front final gear oil drain bolt rear final gear oil fill cap rear final gear oil drain bolt
116
Servicing Your Honda
Maintenance Component
Locations clutch adjuster air cleaner spark plug seat latch owner’s manual air pressure gauge
40 A spare fuse coolant reserve tank spark arrester engine oil fill cap/ dipstick engine oil drain bolt tool kit air cleaner housing drain tube rear suspension spring pre-load adjusters
Servicing Your Honda
117
Tool Kit
The tool kit (1) is stored in the storage compartment (page 53).
After using the tools, be sure to use the rubber band (2) to fasten the tool kit securely.
An optional, larger tool kit may be available. Check with your dealer’s parts department.
REAR
(2)
(1) tool kit
(1)
(2) rubber band
118
Servicing Your Honda
Owner’s Manual Storage
Your ATV provides storage for the owner’s manual so you’ll have it with you for easy reference. Store your owner’s manual (1) in the plastic document bag (2) underside of the rear fender cover (3).
The owner’s manual, air pressure gauge (4) and 40 A spare fuse (5) should be stored in the plastic document bag and fastened with the rubber band (6).
To remove the rear fender cover, see page 121.
Be careful not to flood this area when washing your ATV.
REAR FENDER COVER UNDERSIDE
(6)
(3)
(5)
(1)
(2)
(4)
(1) owner’s manual
(2) plastic document bag
(3) rear fender cover
(4) air pressure gauge
(5) 40 A spare fuse
(6) rubber band
Servicing Your Honda
119
Seat Removal
Refer to Safety Precautions
The seat must be removed for the engine oil filter, air cleaner, spark plug, battery and fuse maintenance and to remove the rear fender cover and tank cover assembly, to access the owner’s manual, air pressure gauge and 40 A spare fuse.
(3)
(6)
(4) (2)
(5)
(1) seat latch
(2) seat
(3) front prongs
(4) tank cover
(7)
(5) hooks
(6) studs
(7) grommets
(1)
Removal
1. Pull the seat latch (1) at the rear of the seat.
2. Slide the seat (2) back and lift it.
Installation
1. Insert the front prongs (3) into the backside of the tank cover (4) and hooks (5) on the frame, and press the studs (6) into the grommets (7).
2. Press down on the seat until locks.
120
Servicing Your Honda
Rear Fender Cover Removal
Refer to Safety Precautions
The rear fender cover must be removed for the battery and fuse maintenance and to access the owner’s manual, air pressure gauge and 40 A spare fuse.
(4) (5)
(2)
(1)
(3)
(1) rubber strap
(2) studs
(3) grommets
(4) rear fender cover
(5) tabs
Removal
1. Remove the seat (page 120).
2. Unhook the rubber strap (1).
3. Firmly pull the studs (2) from the grommets (3).
4. Slide the rear fender cover (4) forward to disengage the tabs (5).
5. Remove the rear fender cover.
Installation
Install the rear fender cover in the reverse order of removal.
Servicing Your Honda
121
Tank Cover Assembly Removal
Refer to Safety Precautions
The tank cover assembly must be removed for the engine oil filter and spark plug maintenance.
(1)
(2)
(1)
(3)
(3)
(1) right studs
(2) tank cover assembly
(3) right tabs
Removal
1. Remove the seat (page 120).
2. Carefully remove the right studs (1) and left studs from the grommets.
3. Remove the tank cover assembly (2) by releasing the right tabs (3) and left tabs from the slits.
Installation
Install the tank cover assembly in the reverse order of removal.
122
Servicing Your Honda
Clip Removal
Removal
1. Pull up the center pin to release the lock.
2. Pull out the clip of the hole.
1.
2.
Installation
1. Insert the clip into the hole.
2. Press down the center pin securely to lock the clip.
1.
2.
Servicing Your Honda
123
Fuel
Refer to Safety Precautions
Fuel Recommendation
type pump octane number unleaded
86 (or higher)
Use only unleaded fuel in your Honda. If you ride your Honda in a country where leaded fuel might be available, take precautions to use only unleaded fuel.
Your engine is designed to use any unleaded gasoline that has a pump octane number of 86 or higher. Gasoline pumps at service stations normally display the pump octane number. For information
on the use of oxygenated fuels, see page 238.
Use of lower octane gasoline can cause persistent “pinging” or
“spark knock” (a loud rapping noise) which, if severe, can lead to engine damage. Light pinging experienced while operating under a heavy load, such as climbing a hill, is no cause for concern.
If pinging or spark knock occurs at a steady engine speed under normal load, change brands of gasoline. If pinging or spark knock persists, consult your dealer.
Never use stale or contaminated gasoline or an oil/gasoline mixture.
Avoid getting dirt, dust, or water in the fuel tank.
124
Servicing Your Honda
Fuel
Fuel Capacity
Fuel tank capacity, including reserve:
3.88 US gal (14.7 ℓ)
Reserve capacity:
1.29 US gal (4.9 ℓ)
When there is only one segment left in the fuel gauge (page 24), fuel
will be low and you should refuel as soon as possible.
Refueling Procedure
Refer to Safety Precautions
(2)
(1)
(1) fuel fill cap
(2) lower edge of filler neck
(cont’d)
Servicing Your Honda
125
Fuel
1. To open the fuel fill cap (1), turn it counterclockwise.
2. Add fuel until the level reaches the lower edge of the filler neck
(2).
Avoid over filling the tank. There should be no fuel in the filler neck.
WARNING 3 WARNING
Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
• Stop the engine and keep heat, sparks and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.
3. After refueling, turn the fuel fill cap clockwise securely.
If you replace the fuel fill cap, use only a Honda Genuine replacement part.
NOTICE
Gasoline can damage the camouflage coating.
Do not allow spilled gasoline to pool on camouflage colored bodywork. Also, do not allow gasoline soaked rags to be placed on camouflage bodywork.
126
Servicing Your Honda
Engine Oil & Filter
Engine oil quality is a major factor that affects both the performance and the service life of the engine.
Using the proper oil (page 128) and filter, and regularly checking,
adding, and changing oil will help extend your engine’s life. Even the best oil wears out. Changing oil helps get rid of dirt and deposits in the engine. Operating the engine with old or dirty oil can damage your engine. Running the engine with insufficient oil can cause serious damage to the engine and transmission.
Change the engine oil as specified in the maintenance schedule on
page 112. When running in very dusty conditions, oil changes
should be performed more frequently than specified in the maintenance schedule.
Servicing Your Honda
127
Engine Oil & Filter
Oil Recommendation
API classification viscosity (weight)
JASO T 903 standard suggested oil *
SG or higher except oils labeled as energy conserving or resource conserving on the circular API service label
SAE 10W-30
MA
Pro Honda GN4 4-stroke oil (USA &
Canada), or Honda 4-stroke oil, or an equivalent motorcycle oil.
* Suggested oils are equal in performance to SJ oils that are not labeled as energy conserving or resource conserving on the circular API service label.
• Your ATV does not need oil additives. Use the recommended oil.
• Do not use oils with graphite or molybdenum additives. They may adversely affect clutch operation.
• Do not use API SH or higher oils displaying a circular API “energy conserving” or “resource conserving” service label on the container. They may affect lubrication and clutch performance.
NOT RECOMMENDED RECOMMENDED
• Do not use non-detergent, vegetable, or castor based racing oils.
128
Servicing Your Honda
Engine Oil & Filter
Other viscosities shown in the following chart may be used when the average temperature in your riding area is within the indicated range.
JASO T 903 standard
The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines.
There are two classes: MA and MB.
Oil conforming to the standard is labeled on the oil container. For example, the following label shows the MA classification.
(1)
(2)
(1) oil code
(2) oil classification
Servicing Your Honda
129
Engine Oil & Filter
Checking & Adding Oil
Refer to Safety Precautions
Check the engine oil level each day before operating your ATV and add if needed.
The oil fill cap/dipstick is located at the front left crankcase.
Before riding your ATV, check the engine oil level.
1. Park your ATV on a firm, level surface.
2. Start the engine in a well-ventilated area and let it idle for 3 – 5 minutes. If the air temperature is below 10°C (50°F), let the engine idle for an additional 5 minutes (a total of 10 minutes).
3. Stop the engine and wait 2 – 3 minutes.
4. Remove the oil check/fill door (1) by disengaging the stud (2) from the grommet and releasing the tabs (3) from the slits.
LEFT SIDE
(2)
(1)
(1) oil check/fill door
(2) stud
(3)
(3) tabs
130
Servicing Your Honda
Engine Oil & Filter
5. Remove the oil fill cap/dipstick (4) from the front crankcase and wipe it clean.
6. Insert the oil fill cap/dipstick without screwing it in, then remove the oil fill cap/dipstick and check the oil level. The oil level should be between the upper level mark (5) and the lower level mark (6) on the oil fill cap/dipstick.
7. If the oil level is near or below the lower level mark, then add the specified oil into the fill cap hole, up to the upper level mark on the oil fill cap/dipstick. Do not overfill.
8. Reinstall the oil fill cap/dipstick.
9. Install the oil check/fill door.
NOTICE
Running the engine with an improper oil level can cause serious engine damage.
LEFT SIDE
(4)
(4) oil fill cap/dipstick (5) upper level mark
(6) lower level mark
(5)
(6)
Servicing Your Honda
131
Engine Oil & Filter
Changing Engine Oil & Filter
Refer to Safety Precautions
Your ATV’s oil filter has very specific performance requirements. Use a new Honda Genuine oil filter specified for your model or a filter of equal quality.
NOTICE
Using the wrong oil filter may result in leaks or engine damage.
This procedure requires mechanical skill and professional tools such as a torque wrench as well as a means for disposing of the drained
fluid (page 202). If you do not have the skills or the tools, see your
dealer.
Change the oil with the engine warm to assure complete and rapid draining.
Drain the Engine Oil:
1. With the ATV on level ground, remove the oil check/fill door
(page 130) and the oil fill cap/dipstick from the front crankcase.
132
Servicing Your Honda
Engine Oil & Filter
2. Place an oil drain pan under the crankcase and remove the engine oil drain bolt (1) and sealing washer (2).
UNDER ENGINE
(2)
(1)
(1) engine oil drain bolt (2) sealing washer
(cont’d)
Servicing Your Honda
133
Engine Oil & Filter
Install a New Engine Oil Filter:
Place shop towels under the oil filter cover because oil will flow out.
1. Remove the seat (page 120) and tank cover assembly (page 122).
2. Remove the oil filter cover (3) and O-rings (4) by removing the bolts (5). Let the remaining oil drain out. Discard the oil filter (6)
in an approved manner (page 202).
3. Apply engine oil to new O-rings and install them to the oil filter cover and crankcase cover.
4. Reposition the spring (7) to the crankcase cover and install a new oil filter with the rubber seal (8) facing out, away from the engine. You will see the “OUT-SIDE (TOWARDS FILTER COVER)” mark (9) on the filter body, near the seal. Use only the Honda
Genuine oil filter or a filter of equivalent quality specified for your model. Using the wrong Honda filter or a non-Honda filter which is not of equivalent quality may cause engine damage.
NOTICE
Improper installation of the oil filter can cause serious engine damage.
RIGHT SIDE
(4)
(5)
(3)
(3) oil filter cover
(4) O-rings
(5) bolts
(6) oil filter
134
Servicing Your Honda
(7)
(6) (8)
(9)
(7) spring
(8) rubber seal
(9) “OUT-SIDE” mark
Engine Oil & Filter
5. Reinstall the oil filter cover, making sure the bolts are tightened to the specified torque:
7 lbf·ft (10 N·m, 1.0 kgf·m)
6. Pour the drained oil into a suitable container and dispose of it in
an approved manner (page 202).
NOTICE
Improper disposal of drained fluids is harmful to the environment.
7. Install the tank cover assembly and seat.
Add Engine Oil:
1. Reinstall the oil drain bolt with the new sealing washer and tighten it to the specified torque:
18 lbf·ft (25 N·m, 2.5 kgf·m)
2. Fill the crankcase with the recommended grade oil approximately:
3.2 US qt (3.0 ℓ)
3. Reinstall the oil fill cap/dipstick.
4. Start the engine and let it idle for 3 – 5 minutes.
5. Stop the engine, wait 2 – 3 minutes and check the oil level. Make sure the oil is between the upper and lower level marks on the oil fill cap/dipstick. If necessary, add more oil but do not overfill.
6. Check that there are no oil leaks.
7. Install the oil check/fill door.
If a torque wrench is not used for installation, see your dealer as soon as possible to verify proper assembly.
Servicing Your Honda
135
Rear Final Gear Oil
Oil Recommendation
type viscosity (weight) suggested oil hypoid gear oil
SAE 80W-90
Honda shaft drive oil or equivalent
Changing Oil
Refer to Safety Precautions
Change the oil with the rear final gear at normal operating temperature to assure complete and rapid draining.
136
Servicing Your Honda
Rear Final Gear Oil
1. Park your ATV on a firm, level surface.
2. Place an oil drain pan under the oil drain bolt (1).
3. Remove the oil fill cap (2), O-ring (3), drain bolt and sealing washer (4).
4. After the oil has completely drained, reinstall the drain bolt with a new sealing washer and tighten it to the specified torque:
9 lbf·ft (12 N·m, 1.2 kgf·m)
5. Pour the drained oil into a suitable container and dispose of it in
an approved manner (page 202).
NOTICE
Improper disposal of drained fluids is harmful to the environment.
6. Fill the rear final gear case with the recommended oil.
4.2 US oz (125 cm 3 )
Make sure the oil level is at the lower edge of the oil fill inspection hole (5).
7. Coat a new O-ring with grease and install it into the fill cap groove and tighten it to the specified torque:
9 lbf·ft (12 N·m, 1.2 kgf·m)
REAR
(5)
(2)
(4)
(3)
(1)
(1) oil drain bolt
(2) oil fill cap
(3) O-ring
(4) sealing washer
(5) oil fill inspection hole
Servicing Your Honda
137
Front Final Gear Oil
Oil Recommendation
type viscosity (weight) suggested oil hypoid gear oil
SAE 80W-90
Honda shaft drive oil or equivalent
Changing Oil
Refer to Safety Precautions
Change the oil with the front final gear at normal operating temperature to assure complete and rapid draining.
138
Servicing Your Honda
Front Final Gear Oil
1. Park your ATV on a firm, level surface.
2. Place an oil drain pan under the oil drain bolt (1).
3. Remove the oil fill cap (2), O-ring (3), drain bolt and sealing washer (4).
4. After the oil has completely drained, reinstall the drain bolt with a new sealing washer and tighten it to the specified torque:
9 lbf·ft (12 N·m, 1.2 kgf·m)
5. Pour the drained oil into a suitable container and dispose of it in
an approved manner (page 202).
NOTICE
Improper disposal of drained fluids is harmful to the environment.
6. Fill the front final gear case with the recommended oil.
11.0 US oz (325 cm 3 )
Make sure the oil level is at the lower edge of the oil fill inspection hole (5).
7. Coat a new O-ring with grease and install it into the fill cap groove and tighten it to the specified torque:
9 lbf·ft (12 N·m, 1.2 kgf·m)
FRONT
(5)
(2)
(4)
(1) oil drain bolt
(2) oil fill cap
(3) O-ring
(1)
(3)
(4) sealing washer
(5) oil fill inspection hole
Servicing Your Honda
139
Coolant
Your ATV’s liquid cooling system dissipates engine heat through the coolant jacket that surrounds the cylinder and cylinder head.
Maintaining the coolant will allow the cooling system to work properly and prevent freezing, overheating, and corrosion.
Coolant Recommendation
Use Pro Honda HP Coolant or an equivalent high quality ethylene glycol antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines. Check the antifreeze container label.
Use only distilled water as a part of the coolant solution. Water that is high in mineral content or salt may be harmful to the aluminum engine.
NOTICE
Using coolant with silicate inhibitors may cause premature wear of water pump seals or blockage of radiator passages. Using tap water may cause engine damage.
The factory provides a 50/50 solution of antifreeze and water in this
ATV. This coolant solution is recommended for most operating temperatures and provides good corrosion protection.
Decreasing the concentration of antifreeze to less than 40% will not provide proper corrosion protection.
140
Servicing Your Honda
Coolant
Increasing the concentration of antifreeze is not recommended because it decreases cooling system performance. Higher concentrations of antifreeze (up to 60%) should only be used to provide additional protection against freezing. Check the cooling system frequently during freezing weather.
Checking & Adding Coolant
Refer to Safety Precautions
Check the engine coolant level each day before operating your ATV and add if needed.
LEFT FRONT
(2)
(3)
(1)
(1) reserve tank
(2) UPPER level mark
(3) LOWER level mark
1. Make sure the vehicle is on level ground.
2. With the engine at normal operating temperature, check the coolant level in the reserve tank (1). It should be between the
UPPER (2) and LOWER (3) level marks.
If the reserve tank is empty, or if coolant loss is excessive, check for leaks and see your dealer for repair.
(cont’d)
Servicing Your Honda
141
Coolant
3. Remove the radiator cap lid (4) by disengaging the stud (5) from the grommet (6).
4. Remove the reserve tank cap (7).
Always add coolant to the reserve tank. Do not attempt to add coolant by removing the radiator cap.
5. Add coolant to the reserve tank as required to bring the coolant level to the UPPER level mark.
FRONT
(4)
(7)
(5)
(4) radiator cap lid
(5) stud
(6)
(6) grommet
(7) reserve tank cap
6. After adding coolant, reinstall the reserve tank cap.
7. Install the radiator cap lid.
142
Servicing Your Honda
Coolant
Coolant Replacement
Refer to Safety Precautions
Coolant should be replaced by your dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer
to the official Honda Service Manual (page 242).
WARNING 3 WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
To properly dispose of drained coolant, refer to You & the
Environment
NOTICE
Improper disposal of drained fluids is harmful to the environment.
Servicing Your Honda
143
Coolant
Radiator Core
Refer to Safety Precautions
Check the air passages for clogging or damage. Remove insects, mud, or any obstruction with low water pressure. Have the radiator checked by your dealer if the air flow is restricted over more than
20% of the radiator surface.
Clean the radiator core after riding the ATV in mud.
The left and center radiator grill covers must be removed to clean the radiator core.
144
Servicing Your Honda
Coolant
To clean the radiator core and radiator grill plate:
1. Remove the radiator cap lid (page 142).
2. Remove the reserve tank (1) by removing the bolt (2) and clips (3)
3. Release the hoses (4) from the guides.
4. Hold the reserve tank being careful not to spill the coolant.
LEFT FRONT
(1)
(2) (3)
(3)
(1) reserve tank
(2) bolt
(3) clips
(4) hoses
(4)
(cont’d)
Servicing Your Honda
145
Coolant
5. Remove the clips.
6. Remove the left radiator grill cover (5) by releasing the tab A (6), tab B (7), tab C (8), hook A (9) and hook B (10).
LEFT FRONT
(3) (9)
(8)
(5)
(7)
(3) clips
(5) left radiator grill cover
(6) tab A
(6) (10)
(7) tab B
(8) tab C
(9) hook A
(10) hook B
146
Servicing Your Honda
Coolant
7. Remove the center radiator grill cover by releasing the tab A, tab
B, hook A and hook B.
FRONT
(9) (12)
(11)
(7)
(6)
(6) tab A
(7) tab B
(9) hook A
(10)
(10) hook B
(11) center radiator grill cover
(12) radiator core
8. Wash the radiator core (12) and radiator grill covers.
NOTICE
Do not apply pressured water directly to the radiator core.
The pressured water can damage the radiator core.
9. Install the removed parts in reverse order of removal.
Servicing Your Honda
147
Air Cleaner
Refer to Safety Precautions
Proper air cleaner maintenance is very important for off-road vehicles.
A dirty, water-soaked, worn-out, or defective air cleaner will allow dirt, dust, mud, and other impurities to pass into the engine.
Service the air cleaner more frequently if you ride in unusually wet or dusty areas. Your dealer can help you determine the correct service interval for your riding conditions.
Your ATV’s air cleaner has very specific performance requirements.
Use a new Honda Genuine air cleaner specified for your model or an air cleaner of equal quality.
NOTICE
Using the wrong air cleaner may result in premature engine wear.
Proper air cleaner maintenance can prevent premature engine wear or damage, expensive repairs, low engine power, poor gas mileage, and spark plug fouling.
NOTICE
Improper or lack of proper air cleaner maintenance can cause poor performance and premature engine wear.
148
Servicing Your Honda
Cleaning
1. Remove the seat (page 120).
UNDER SEAT
(1) (3)
Air Cleaner
(1) spring hooks
(2) retainer clips
(2) (2)
(3) air cleaner housing cover
2. Unlatch the spring hooks (1) and retainer clips (2).
3. Remove the air cleaner housing cover (3).
(cont’d)
Servicing Your Honda
149
Air Cleaner
4. Loosen the screw (4) and remove the air cleaner assembly (5) from the air cleaner housing.
5. Remove the clamp (6).
6. Remove the air cleaner (7) from the air cleaner body (8).
7. Gently wash the air cleaner in clean, non-flammable (high flash point) solvent such as kerosene — not gasoline. After cleaning, gently squeeze out the remaining solvent. Avoid twisting or wringing the air cleaner. This can tear the foam.
8. Inspect for tears or cracks in the foam or seams of the air cleaner.
Replace the air cleaner if it is damaged.
9. Allow the air cleaner to dry thoroughly before applying oil. A wet air cleaner will not fully absorb the oil.
10. Pour clean Pro Honda Foam Filter Oil or an equivalent (Canada:
Honda Foam Filter Oil or an equivalent) over the entire surface of the air cleaner. Use both hands to evenly spread the oil into the air cleaner. Gently squeeze out any excess oil. (To keep your hands dry, place the air cleaner in a clean plastic bag before spreading the oil into the air cleaner.)
UNDER SEAT
(8)
(6) (7)
(4)
(4) screw
(5) air cleaner assembly
(6) clamp
150
Servicing Your Honda
(7) air cleaner
(8) air cleaner body
(5)
Air Cleaner
11. Install the air cleaner on the air cleaner body.
12. Install the clamp.
13. Insert the air cleaner assembly into the air cleaner housing.
14. Fasten the screw.
15. Reassemble by reversing the disassembly sequence.
• Install the air cleaner housing cover with the FRONT mark (9) facing forward and fit the cut out of the tab (10) at the end of the air cleaner.
UNDER SEAT
(9) (10)
(9) FRONT mark
(10) tab
(10)
Servicing Your Honda
151
Air Cleaner
Dust Cover
UNDER SEAT
(1)
(2)
(1) dust cover (2) breather joint
Do not push the dust cover (1) too far into the breather joint (2).
If the dust cover is dirty, clean it.
152
Servicing Your Honda
Air Cleaner
Air Cleaner Housing Drain Tube
The air cleaner housing drain tube should be serviced in accordance with the Maintenance Schedule. (Riding through water may require more frequent inspection.) If deposits can be seen in the drain tube, the tube must be cleaned before starting the vehicle.
REAR
(1) drain tube
(2) clip
(3) (1) (2)
(3) air cleaner housing
1. Remove the drain tube (1) by removing the clip (2) under the air cleaner housing (3).
2. Drain the deposits.
3. Reinstall the drain tube, securing it with the clip.
Servicing Your Honda
153
Engine
Throttle
Throttle Freeplay
Refer to Safety Precautions
RIGHT HANDLEBAR
(2) (4)
(B)
(A)
1/8 – 5/16 in
(3 – 8 mm)
(3) (1)
(1) throttle lever
(2) rubber sleeve
(3) throttle cable adjuster
Inspection
Check freeplay at the throttle lever (1).
Freeplay:
1/8 – 5/16 in (3 – 8 mm)
(4) lock nut
(A) decrease freeplay
(B) increase freeplay
Adjustment
1. Slide the rubber sleeve (2) back to expose the throttle cable adjuster (3).
2. Loosen the lock nut (4).
3. Turn the adjuster to obtain the correct freeplay.
4. Tighten the lock nut and reinstall the sleeve.
5. After adjustment, check for smooth operation of the throttle lever from fully closed to fully open in all steering positions.
154
Servicing Your Honda
Throttle
Throttle Inspection
Refer to Safety Precautions
1. Check that the throttle assembly is positioned properly and the securing bolts are tight.
2. Check for smooth operation of the throttle lever from fully open to fully closed in all steering positions. If there is a problem, see your dealer.
3. Inspect the condition of the throttle cable from the throttle lever down to the throttle body. If the cable is kinked or chafed, have it replaced.
4. Check the throttle cable for tension or stress in all steering positions.
5. Lubricate the throttle cable with a commercially available cable lubricant to prevent premature wear and corrosion.
Servicing Your Honda
155
Clutch System
Your ATV’s shift-activated, wet, multiplate clutch is part of the primary drive system. Proper adjustment allows a smooth, gradual engagement when shifting gears.
Clutch Adjustment
Refer to Safety Precautions
LEFT FRONT
(2)
(1) lock nut
(1)
(2) clutch adjuster
1. Make sure the engine is cool.
2. Make sure the ignition switch is OFF ( w ).
3. Loosen the lock nut (1).
4. Turn the clutch adjuster (2) counterclockwise until you feel slight resistance.
5. Turn the adjuster 1/4 turn clockwise, then tighten the lock nut to hold the adjuster in this position.
6. After adjustment, start the engine and test ride your ATV to be sure the clutch is operating properly.
If you cannot get proper adjustment, or the clutch does not work properly, the clutch friction discs may be worn. See your dealer or
refer to official Honda Service Manual (page 242).
156
Servicing Your Honda
Reverse Inhibitor System
Reverse Inhibitor System Adjustment
Refer to Safety Precautions
LEFT HANDLEBAR
(1)
(4)
(5)
(3)
(1) dust cover
(2) reverse assist lever
(3) rubber sleeve
1/16 – 3/16 in
(2 – 4 mm)
(4) lock nut
(5) adjusting nut
(2)
1. Turn over the dust cover (1).
2. Check the reverse assist lever (2) freeplay, measured at the reverse assist lever end near the cable:
1/16 – 3/16 in (2 – 4 mm)
3. To adjust, slide the rubber sleeve (3), loosen the lock nut (4) and turn the adjusting nut (5) to obtain the correct freeplay.
After adjustment, tighten the lock nut securely.
4. Return the dust cover and rubber sleeve.
Other Checks
Check the reverse assist lever and cable for loose connections or other damage. If the cable is worn or kinked, have it replaced by your dealer.
Servicing Your Honda
157
Spark Plug
Spark Plug Recommendation
standard spark plug BKR5E-11 (NGK) or
K16PR-U11 (DENSO)
Use only the recommended type of spark plug in the recommended heat range.
NOTICE
Using spark plugs with an improper heat range can cause engine damage.
Spark Plug Inspection & Replacement
Refer to Safety Precautions
1. Remove the seat (page 120) and tank cover assembly (page 122).
2. Clean any dirt from around the spark plug base.
3. Disconnect the spark plug cap (1). Take care to avoid damaging the spark plug wire when disconnecting the cap.
4. Using a spark plug wrench provided in the tool kit, remove the spark plug.
LEFT SIDE
(1)
(1) spark plug cap
158
Servicing Your Honda
Spark Plug
5. Inspect the electrodes and center porcelain for deposits, corrosion, or carbon fouling. If the corrosion or deposits are heavy, replace the plug. Clean a carbon or wet-fouled plug with a plug cleaner, if available, or a wire brush. Inspect the spark plug electrodes for wear. The center electrode (2) should have a flat tip and sharp edges, and the side electrode (3) should not be eroded.
If the electrodes and insulator tip appear unusually fouled or burned, we suggest that you contact your dealer.
6. Discard the spark plug if there is apparent wear or if the insulator is cracked or chipped.
7. Using a wire-type feeler gauge, check the spark plug gap (4). If adjustment is necessary, bend the side electrode carefully.
The gap should be:
0.039 – 0.043 in (1.00 – 1.10 mm)
(4)
(3)
0.039 – 0.043 in
(1.00 – 1.10 mm)
(2)
(2) center electrode
(3) side electrode
(4) spark plug gap
(cont’d)
Servicing Your Honda
159
Spark Plug
8. With the plug washer attached, thread the spark plug in by hand to prevent cross-threading.
9. Tighten the spark plug:
• If the old plug is good:
1/8 turn after it seats.
• If installing a new plug, tighten it twice to prevent loosening: a) First, tighten the plug:
NGK: 3/4 turn after it seats.
DENSO: 1/2 turn after it seats.
b) Then loosen the plug.
c) Next, tighten the plug again:
1/8 turn after it seats.
NOTICE
An improperly tightened spark plug can damage the engine. If a plug is too loose, the piston may be damaged. If a plug is too tight, the threads may be damaged.
10. Connect the spark plug cap. Take care to avoid pinching any cables or wires.
11. Install the remaining parts in the reverse order of removal.
160
Servicing Your Honda
Valves
Valve Inspection
Refer to Safety Precautions
Valve clearance should be: intake: 0.006 in (0.15 mm) exhaust: 0.009 in (0.23 mm)
Excessive clearance will cause noise. Insufficient clearance will cause loss of power and possibly damage the valves.
For those who are mechanically proficient and have the proper tools, instructions on adjusting valve clearances are given in the official
Honda Service Manual. Otherwise, the valves should be adjusted by your dealer.
Servicing Your Honda
161
Spark Arrester
Refer to Safety Precautions
The spark arrester must be serviced every 100 operating hours to maintain its efficiency.
Regular servicing prevents carbon build up (which can diminish engine performance) and also complies with USDA regulations for regular maintenance to assure proper function. The spark arrester prevents random sparks from the combustion process in your engine from reaching the environment.
The use of safety glasses is recommended for this procedure.
Because of the possible fire hazard, check that there are no combustible materials in the area before purging the spark arrester.
REAR
(1)
(1) bolt
1. Select a well-ventilated area free of combustible materials and make sure the exhaust pipe is cool.
2. Remove the bolt (1).
3. Start the engine and rev it up approximately twenty times while momentarily creating exhaust system back pressure by blocking the end of the muffler with a shop towel.
4. Stop the engine and allow the exhaust pipe to cool.
5. Reinstall the bolt securely.
162
Servicing Your Honda
Chassis
Suspension
Your front and rear suspension systems use springs and hydraulic damping devices that suspend your weight and most of the weight of your ATV.
The oil damper systems hydraulically control the natural compression and rebound of the suspension springs so that traction and comfort are maintained as the wheels ride over rough terrain.
The spring pre-loads for your front and rear suspension systems adjust the amount of force required to begin compression of the spring.
Consider adjusting your suspensions pre-load whenever you change your normal load, by adding or subtracting cargo, accessories, or when riding conditions change.
The way you ride your ATV and the type of ride you want to experience can also influence your suspension needs.
Lower spring pre-load provides a softer ride and is usually preferred for light loads and smooth terrain. Higher spring pre-load provides a firmer ride and is recommended for heavy loads and rough terrain.
Suspension Adjustment
Using a pin spanner, which is available from your dealer, the suspensions can be adjusted for rider weight and riding conditions by changing the spring pre-load.
Do not attempt to disassemble, service, or dispose of the damper; see your dealer. The instructions found in this owner’s manual are limited to adjustments of the shock assembly only.
Servicing Your Honda
163
Suspension
Suspension Spring Pre-Load
Refer to Safety Precautions
REAR FRONT
(1) (1)
1 2 3 4 5
(2)
(1) spring pre-load adjuster
(2) pin spanner
(2)
1 2 3 4 5
The spring pre-load adjuster (1) has 5 positions for different load or riding conditions.
Use the pin spanner (2) to adjust the shock spring pre-load.
164
Servicing Your Honda
Suspension
Position 1: for a light load and smooth terrain.
Position 2: standard position.
Positions 3 to 5: for when the ATV is more heavily loaded. (Also increase spring pre-load for stiffer suspension.)
Make sure that both shock absorbers are adjusted to the same position.
Always adjust the shock absorber position in sequence (1-2-3-4-5 or
5-4-3-2-1). Attempting to adjust directly from 1 to 5 or 5 to 1 may damage the shock absorber.
Servicing Your Honda
165
Brakes
The hydraulic disc brakes (front) and a single hydraulic/mechanical disc brake (rear) on your ATV dissipate the heat generated by the friction of the brake pads on the disc as the wheels are slowed.
As the brake pads wear, the brake fluid level will drop. A leak in the system will also cause the level to drop.
There are no adjustments to perform, but fluid level and pad wear must be inspected periodically. The system must be inspected frequently to ensure there are no fluid leaks.
If the brake lever or brake pedal freeplay does not feel within the normal range while riding, check the brake pads for wear
Worn pads should be replaced. If the pads are not worn beyond the recommended limit, there is probably air in the brake system. See your dealer to have the air bled from the system.
Brake Fluid Recommendation
brake fluid Honda DOT 4 Brake Fluid
The recommended brake fluid is Honda DOT 4 Brake Fluid, or any brake fluid of equal quality and performance. Use fresh brake fluid from a sealed container. Be sure to read the label before opening the sealed container. An opened container may be contaminated or may have absorbed moisture from the air.
166
Servicing Your Honda
Brakes
Fluid Level Inspection
Refer to Safety Precautions
If your inspection indicates a low fluid level, have your dealer add the recommended fluid.
Do not add or replace brake fluid, except in an emergency. If you do add fluid, have your dealer check the system as soon as possible.
NOTICE
Brake fluid can damage plastic and painted surfaces. Handle with care.
Wipe up spills immediately. Avoid brake fluid contact with skin or eyes. If it comes in contact with your eyes, wash them out with clean water and immediately call a doctor. If it comes in contact with your skin, wash with clean water and, if necessary, call a doctor.
Front Brake Fluid Level
RIGHT HANDLEBAR
(1) LOWER level mark
(1)
(cont’d)
Servicing Your Honda
167
Brakes
With the ATV on a level surface, check the fluid level.
It should be above the LOWER level mark (1). If the level is at or below the LOWER level mark, check the brake pads for wear
Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks.
Rear Brake Fluid Level
RIGHT SIDE
(2)
(3)
(2) UPPER level mark (3) LOWER level mark
With the ATV on a level surface, check the fluid level.
It should be between the UPPER (2) and LOWER (3) level mark. If the level is at or below the LOWER level mark, check the brake pads for
Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks.
Other Inspections
• Make sure there are no fluid leaks.
• Check for deterioration or cracks in the hoses and fittings. If the hoses are worn or cracked, have them replaced by your dealer.
168
Servicing Your Honda
Brakes
Brake Pad Wear
Refer to Safety Precautions
Brake pad wear will depend upon the severity of usage and riding conditions. The pads will wear faster in wet or muddy conditions.
Inspect the pads visually during all regular service intervals to determine the pad wear.
RIGHT FRONT (Left side similar)
(1)
(1)
(2)
(1) wear indicator
(2)
(2) edge of reference mark
Check the wear indicator (1). If the wear indicator aligns with the edge of the reference mark (2), both pads must be replaced, see your dealer for this replacement.
Always inspect both pads in both the right and left front brake calipers.
(cont’d)
Servicing Your Honda
169
Brakes
REAR
(4)
(3)
(4) reference mark (3) wear indicator
Check the wear indicator. If the wear indicator (3) aligns with the reference mark (4), replace both pads as a set, see your dealer for this service.
170
Servicing Your Honda
Brakes
Rear Brake Lever Freeplay
LEFT HANDLEBAR
(1)
1 – 1 3/16 in
(25 – 30 mm)
(1) rear brake lever/parking brake lever
Inspection
1. Press down on the rear brake pedal several times.
2. Measure the distance the rear brake lever/parking brake lever (1) moves before the brake starts to take hold. Freeplay
(measurement at the tip of the end of the brake lever) should be:
1 – 1 3/16 in (25 – 30 mm)
3. If necessary, adjust to the specified range.
(cont’d)
Servicing Your Honda
171
Brakes
Adjustment
RIGHT REAR
(3)
(B)
(A)
(2)
(2) brake lever adjusting nut
(3) brake arm pin
(A) increase freeplay
(B) decrease freeplay
Adjust the freeplay of the rear brake lever/parking brake lever with the front wheels pointed straight ahead.
Turn the brake lever adjusting nut (2), located on the brake operating rod at the brake caliper. Make sure the cutout on the adjusting nut is properly seated on the brake arm pin (3).
Other Inspections
• Check that the brake lever and brake pedal assemblies are positioned properly and the securing bolts are tight.
• Make sure that the brake cable, brake arm, spring, P/R lever, and fasteners are in good condition.
172
Servicing Your Honda
Brakes
Brake Light Switch Adjustment
Refer to Safety Precautions
Rear Brake Only:
Check the operation of the rear brake light switch (1) at the right side behind the engine from time to time. Adjustment is done by turning the adjusting nut (2). Hold the rear brake light switch and turn the nut in direction (A) if the switch operates too late and in direction (B) if the switch operates too soon.
RIGHT REAR
(2)
(A)
(B)
(1)
(1) rear brake light switch (2) adjusting nut
Servicing Your Honda
173
Tires
To safely operate your ATV, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.
WARNING 3 WARNING
Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
This ATV is equipped with low pressure tubeless tires. Although the tires are designed specifically for off-road use, they are not immune to punctures. Always select your riding area with care.
The following pages give detailed information on how and when to check your air pressure, how to inspect your tires for wear and damage, and our recommendations for tire repair and replacement.
174
Servicing Your Honda
Tires
Air Pressure
Refer to Safety Precautions
Properly inflated tires provide the best combination of handling, tread life, and riding comfort. Generally, underinflated tires wear unevenly, adversely affect handling, and are more likely to fail from being overheated. Overinflated tires make your ATV ride harshly, are more prone to damage from surface hazards, and wear unevenly.
Make sure the air valve caps are secure. If necessary, install new caps.
(cont’d)
Servicing Your Honda
175
Tires
Always check air pressure when your tires are “cold.” If you check air pressure when your tires are “warm” — even if your ATV has only been ridden for a few miles — the readings will be higher. If you let air out of warm tires to match the recommended cold tire pressures, the tires will be underinflated. Be sure to check tire pressure at the riding site, since changes in altitude can affect air pressure.
The recommended “cold” tire pressures are:
RECOMMENDED
PRESSURE
FRONT
4.4 psi (30 kPa)
REAR
4.4 psi (30 kPa)
176
Servicing Your Honda
Tires
A manually operated tire pump should be used rather than the high pressure system found in service stations. This will minimize the possibility of tire damage from overinflation. If you use a high pressure system at a service station, add air in small amounts and check the pressure increase frequently to prevent possible tire damage from overinflation.
WARNING 3 WARNING
Operating this ATV with improper tires, or with uneven tire pressure may cause loss of control, and you could be seriously injured or killed.
• Always use the size and type tires specified in this owner’s manual for this vehicle.
• Always maintain proper tire pressure as described in this owner’s manual.
Inspection
Refer to Safety Precautions
Whenever you check the tire pressures, you should also look for:
• Bumps or bulges in the side of the tire or the tread. Replace any tire that has a bump or bulge.
• Cuts, slits, or cracks in the tires. Replace the tire if you can see fabric or cord.
• Nails or other foreign objects embedded in the side of the tire or tread.
• Excessive tread wear.
(cont’d)
Servicing Your Honda
177
Tires
Also, if you hit a pothole or other hard object while riding, stop as soon as you safely can and carefully inspect the tires for damage.
Tread Wear
(2)
NEW
(1)
3/16 in
(4 mm)
Replace
(3)
(1) groove depth
(2) wear indicator
(3) wear indicator location mark
To check the condition of a tire tread, measure the groove depth (1) in the center of the tire, or check the wear indicator (2).
For best performance, you should replace a tire before the tread depth at the center reaches the following limits: front rear
3/16 in (4 mm)
3/16 in (4 mm)
178
Servicing Your Honda
Tires
Tire Repair
Refer to Safety Precautions
A tire that is repaired, either temporarily or permanently, will have lower speed and performance limits than a new or undamaged tire.
A temporary repair can sometimes be made in an emergency situation. However, since a temporary repair may not hold, you must ride very slowly, preferably without any cargo, and have the tire replaced or permanently repaired as soon as possible. (For more information on temporary repairs, see If You Have a Flat Tire ,
A permanent repair, such as an internal plug patch, can be made if a tire has only a small puncture in the tread area. However you may not be able to safely carry as much weight. If you choose to have a tire repaired, be sure the repair work is performed by a professional.
If you have a tire professionally repaired at a non-Honda facility, we recommend that you have the work checked by your dealer.
Servicing Your Honda
179
Tires
Tire Replacement
Refer to Safety Precautions
The tires that came on your ATV were designed to match the performance capabilities of your ATV and provide the best combination of handling, braking, and comfort.
It is best to replace all four tires, however if that is not possible, you must replace the tires in pairs (front or rear) with tires of the same size and type as the originals. Never replace just one tire.
WARNING 3 WARNING
Installing improper tires on your ATV can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in this owner’s manual.
The recommended tires for your ATV are: front rear
AT25 × 8-12 11
AT25 × 10-12 11
MAXXIS MU25
MAXXIS MU26
When you replace a tire, remember:
Have the tire replaced by your dealer if possible.
If you have a tire professionally replaced at a non-Honda facility, we recommended that you have the work checked by your dealer.
180
Servicing Your Honda
Refer to Safety Precautions
Guards
(1) (2)
(3)
(4)
(1) engine guard
(2) skid plate
(5)
(3) front boot guards
(4) front driveshaft guards
(5) rear driveshaft guards
The engine guard (1) protects the engine crankcase.
The skid plate (2) protects the frame.
The front boot guards (3) protect the rubber driveshaft boots, and the front driveshaft guards (4) protect the front driveshafts.
The rear driveshaft guards (5) protect the rubber driveshaft boots and the rear driveshafts.
Check the guards and plate for cracks, damage or looseness at intervals shown in the Maintenance Schedule.
Have the guards and skid plate replaced if they are cracked or damaged. If the guard and plate bolts are loose, tighten them securely.
Servicing Your Honda
181
Drivetrain Boots
Refer to Safety Precautions
FRONT REAR
(1)
(1) rubber driveshaft boots
(1)
(2)
(2) rubber propeller shaft boots
(3) rubber yoke joint boot
(3) (2)
Check the rubber driveshaft boots (1), rubber propeller shaft boots
(2) and rubber yoke joint boot (3) for cuts, damage or leaking grease.
If necessary, have your dealer replace them.
182
Servicing Your Honda
Electrical
Battery
Your ATV has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water as you would with a conventional-type battery.
NOTICE
Your battery is a maintenance-free type and can be permanently damaged if the cap strip is removed.
Electrical accessories use current from the battery, even when the ignition is OFF ( w ). Limited operation also allows the battery to discharge.
If you have electrical accessories on your ATV or do not ride frequently, we recommend that you charge the battery frequently
(see Battery Charging
If you do not expect to ride your ATV for at least two weeks, we recommend you remove the battery, or at least disconnect the battery cables (negative cable first).
If you plan to store your ATV, see Battery Storage
If your battery seems weak and/or is leaking electrolyte (causing slow starting or other electrical problems), see your dealer.
WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash your hands after handling.
Servicing Your Honda
183
Battery
Battery Storage
Refer to Safety Precautions
If you plan to store your ATV, we recommend you remove the battery and store it where it can be charged at least every 30 days to maintain its service life.
If you do not remove the battery, we recommend disconnecting the battery cables (negative cable first).
You will get the best storage results from removing the battery and slow charging it every 30 days (see Battery Charging
Before you remove the battery, be sure to read all the information that follows, as well as the information on the battery label.
WARNING 3 WARNING
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.
Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.
184
Servicing Your Honda
Battery
The battery is located in a compartment under the rear fender cover.
UNDER REAR FENDER COVER
(2) (1)
(4)
(5)
(5)
(3)
(1) rubber band
(2) negative (–) terminal lead
(3) battery
(4) positive (+) terminal lead
(5) terminal nuts
Removal
1. Make sure the ignition switch is OFF ( w ).
2. Remove the seat (page 120).
3. Remove the rear fender cover (page 121).
4. Release the rings and remove the rubber band (1).
5. Disconnect the negative (–) terminal lead (2) from the battery (3) first, then disconnect the positive (+) terminal lead (4).
6. Remove the battery taking care not to drop the terminal nuts (5).
(cont’d)
Servicing Your Honda
185
Battery
7. Charge the battery (see following section).
8. Store your battery in an easy-to-reach location off the floor, in an area protected from freezing temperature and direct sunlight.
9. Clean the compartment after removing the battery for storage.
Dry the compartment.
10. Slow charge the battery (see following section) once every
30 days.
Installation
1. Check that the battery rubber (6) for damage. If necessary, replace the battery rubber.
2. Make sure the battery rubber is properly installed.
3. Reinstall the battery in the reverse order of removal.
Be sure to connect the positive (+) terminal first, then the negative (–) terminal.
4. Make sure all bolts and other fasteners are secure.
5. Install the removed parts in reverse order of removal.
(6)
(6) battery rubber
After the battery is reconnected, check the clock. Readjust the clock
186
Servicing Your Honda
Battery Charging
Refer to Safety Precautions
(1)
Battery
(1) charger
Be sure to read the information that came with your battery charger and follow the instructions on the battery. Improper charging may damage the battery.
We recommend using a charger (1) designed specifically for your
Honda, which can be purchased from your dealer. These units can be left connected for long periods without risking damage to the battery. However, do not intentionally leave the charger connected longer than the time period recommended in the charger’s instructions. Avoid using an automotive-type battery charger. An automotive charger can overheat an ATV battery and cause premature damage.
Servicing Your Honda
187
Appearance Care
Frequent cleaning and polishing will keep your Honda looking newer longer.
Frequent cleaning also identifies you as an owner who values his ATV.
A clean ATV is also easier to inspect and service.
General Recommendations
Refer to Safety Precautions
• To clean your ATV, you may use:
– water
– Hondabrite
– a mild, neutral detergent and water
– a mild spray and wipe cleaner/polisher
– a mild spray and rinse cleaner/degreaser and water
• Avoid products that contain harsh detergents or chemical solvents that could damage the metal, paint, plastic, and camouflage coating on your ATV (Honda SxS).
• If your ATV is still warm from recent operation, give the engine and exhaust system time to cool off.
• Park in a shady area. Washing your ATV in bright sunlight may cause the finish to fade because water droplets intensify the sun’s brightness.
• Spotting is also more likely because surface water can dry before you have time to wipe it off.
• Clean your ATV regularly to protect surface finishes.
• We recommend the use of a low pressure garden hose to wash your ATV. High pressure washers (like those at coin-operated car washers) can damage certain parts of your ATV.
NOTICE
High pressure water (or air) can damage certain parts of your ATV.
Water entering the muffler may damage the oxygen sensor.
• After cleaning, inspect for damage, wear, and leaks (fuel, oil, coolant and brake fluid).
188
Servicing Your Honda
Appearance Care
Washing Your ATV with a Mild Detergent
Refer to Safety Precautions
1. Cover or plug the exhaust outlet prior to washing your ATV.
2. Rinse your ATV thoroughly with cool water to remove loose dirt.
3. Fill a bucket with cool water. Mix in a mild, neutral detergent, such as dish washing liquid or a product made especially for washing motorcycles or automobiles.
4. Wash your ATV with a sponge or soft towel. As you wash, check for heavy grime. If necessary, use a mild cleaner/degreaser to remove the grime.
5. After washing, rinse your ATV thoroughly with plenty of clean water to remove any residue. Detergent residue can corrode alloy parts.
6. Dry your ATV with a chamois or a soft towel. Leaving water on the surface to air dry can cause dulling and water spots. As you dry, inspect for chips and scratches.
7. Remove the cover or the plug from exhaust outlet. Then, start the engine and let it idle for several minutes. The engine heat will help dry moist areas.
8. As a precaution, ride your ATV at a slow speed and apply the brakes several times. This will help dry the brakes and restore normal braking performance.
If the inside of the headlight lens appears clouded immediately after washing, it should clear after a few minutes of riding.
Servicing Your Honda
189
Appearance Care
Spray Cleaning Your ATV
Refer to Safety Precautions
Avoid using spray cleaner products on the tires or suspension components.
Suggestions for using spray cleaner(s) follow:
ATV condition
Dust and fingerprint smudges.
Light road grimes.
Heavy grime. Oil leaks.
Brake dust.
Dull, corroded chrome or aluminum.
Recommended Cleaning
Apply a spray cleaner/polish and wipe paint, chrome, glass, and clear plastic.
Spray any difficult-to-reach or very dirty areas with a spray cleaner/degreaser.
Rinse and dry.
Apply a spray cleaner/polish and wipe with a non-abrasive cloth.
Use a spray cleaner/degreaser.
If necessary, rub with a sponge.
Rinse and dry.
Apply a spray cleaner/polish and wipe with a non-abrasive cloth.
Apply a high quality chrome/ aluminum polish and wipe with a non-abrasive cloth.
190
Servicing Your Honda
Appearance Care
Exhaust Pipe and Muffler Maintenance
Refer to Safety Precautions
The exhaust pipe and muffler are stainless steel but may become stained by mud or dust.
To remove mud or dust, use a wet sponge and a liquid kitchen abrasive, then rinse well with clean water. Dry with chamois or a soft towel.
If necessary, remove heat stains by using a commercially available fine texture compound. Then rinse by the same manner as removing mud or dust.
Servicing Your Honda
191
Appearance Care
Finishing Touches
Refer to Safety Precautions
After washing your ATV, consider using a commercially available spray cleaner/polish or quality liquid or paste wax to finish the job.
Use only a non-abrasive polish or wax made specifically for motorcycles or automobiles. Apply the polish or wax according to the instructions on the container.
If a surface on your ATV is chipped or scratched, your dealer has touch-up paint to match your ATV’s color. Be sure to use your ATV’s
color code (page 227) when you buy touch-up paint.
If the frame has a chip that exposes the metal, first apply primer (to prevent corrosion) and then apply the touch-up paint. Several thin layers of touch-up paint are better than one thick coat.
192
Servicing Your Honda
Tips
Tips Here’s helpful advice on how to prepare for an off-road adventure, how to transport and store your Honda, and how to be an environmentally responsible ATV owner.
Preparing for a Ride .................................................................. 194
What to Take to the Riding Area............................................ 194
What to Take on the Trail ...................................................... 195
Transporting Your Honda ......................................................... 196
Storing Your Honda.................................................................. 198
Preparation for Storage.......................................................... 199
Removal from Storage ........................................................... 201
You & the Environment ............................................................ 202
Tips
193
Preparing for a Ride
A safe and enjoyable ride begins with good planning and preparation. Always ride with at least one other person in case you have trouble, and let someone know where you’re going and when you expect to return.
Before riding in an unfamiliar area, find out in advance if you need special permits, get maps so you can study the terrain, and talk to other riders who know the area. The Forest Service and the Bureau of Land Management (USA only), the Ministry of Natural Resources
(Canada only), riding clubs, and off-road magazines are good sources of information.
What to Take to the Riding Area
Along with your ATV and riding gear, you should take along some tools and supplies in case you have a problem. For some of the difficulties you might encounter, see Taking Care of the Unexpected ,
We recommend that you always take water, food, a first aid kit, and your owner’s manual. Other items you should consider loading on your truck or trailer include:
• a tool kit
• tire repair supplies and tools, and tires
• extra parts, control levers, cables, and spark plugs
• wire, duct tape, and rope
• extra gasoline
For safety, all refueling should be done at a gas station on the way to the riding area or at your base camp.
194
Tips
Preparing for a Ride
What to Take on the Trail
What you take with you during a ride depends on the kind of terrain, how long you expect to ride, how far you might go from your base camp or help, and how experienced you or your companions are in making repairs.
If you decide to take some tools, spare parts, or other supplies on the trail, be sure you can carry them safely and know how to use them.
Also, be sure to follow the loading guidelines and weight limit
Tips
195
Transporting Your Honda
Do not tow your ATV behind a car or other vehicle.
When you transport your ATV, we recommend that you carry the vehicle in its normal operating position (on all four wheels). Do not incline the vehicle upright on its rear end. This can damage the vehicle, and leaking gasoline could be a hazard.
Follow these procedures:
1. Set the parking brake and place the transmission in gear.
196
Tips
Transporting Your Honda
2. Secure the vehicle with tie-down straps in the areas shown.
• Suitable tie-down straps are available from your dealer.
• Ordinary rope is not recommended because it can stretch under load.
• Using tie-down straps in any other areas can damage your ATV.
3. Rock the vehicle back and forth to make sure the tie-down straps are tight and the vehicle is secure.
(1)
(2)
(3)
(1) front cargo rack
(2) front carry pipe
(4)
(3) rear cargo rack
(4) trailer hitch
Tips
197
Storing Your Honda
If you won’t be riding for an extended period, such as during the winter, thoroughly inspect your ATV and correct any problem before storing it. That way, needed repairs won’t be forgotten and it will be easier to get your ATV running again.
For more information about storage, refer to the Honda Winter
Storage Guide , available from your dealer (USA only).
We suggest you perform the following procedures to keep your ATV in top condition. These storage procedures will reduce the deterioration that can occur during storage.
198
Tips
Storing Your Honda
Preparation for Storage
Refer to Safety Precautions
1. Change the engine oil and filter (page 132).
2. Make sure the cooling system is filled with a 50/50% antifreeze
3. Fill the fuel tank. Make sure the fuel fill cap is properly installed.
4. To prevent rusting in the cylinder, perform the following:
• Remove the spark plug cap from the spark plug (page 158).
• Remove the spark plug.
Do not connect the spark plug to the spark plug cap.
• Pour a tablespoon (15 – 20 cc) of clean engine oil into the cylinder and cover the spark plug hole with a piece of cloth.
• With the engine stop switch in the RUN ( e ) position, press the start/over ride button several times to crank the engine and distribute the oil.
• Reinstall the spark plug and spark plug cap.
(cont’d)
Tips
199
Storing Your Honda
5. Remove the battery and charge it fully. Store it in an area protected from freezing temperatures and direct sunlight. Slow
charge the battery (page 187) once a month.
WARNING 3 WARNING
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.
Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.
6. Wash and dry your ATV. Wax all painted surfaces.
7. Inflate the tires to their recommended pressures (page 176).
8. Store your ATV in an unheated area, free of dampness, away from sunlight, with a minimum of daily temperature variation.
9. Place your ATV on blocks to lift all tires off the floor.
10. Cover your ATV with a porous material. Avoid using plastic or similar non-breathing, coated materials that restrict air flow and allow heat and moisture to accumulate.
NOTICE
Do not store your ATV in an upright position for extended periods of time. The ATV should be stored with all four tires on the ground. This can damage the vehicle, and leaking gasoline could be a hazard.
200
Tips
Storing Your Honda
Removal from Storage
Refer to Safety Precautions
1. Uncover and clean your ATV.
2. If your ATV has been stored for more than four months —
change the engine oil (page 132).
3. If your ATV has been stored for more than two months — ask your dealer to drain and replace the fuel.
4. Charge the battery (page 187) as required. Install the battery.
5. Perform a pre-ride inspection (page 61), then test-ride your ATV
at low speeds.
Tips
201
You & the Environment
Owning and riding an ATV can be enjoyable, but you must do your part to protect nature. When you show respect for the land, wildlife, and other people, you also help preserve the sport of off-road riding.
Following are tips on how you can be an environmentally responsible
ATV owner.
• Tread Lightly.
Stay on existing roads and trails, avoid surfaces that are easily damaged, and ride only in areas approved for offroad vehicles.
• Keep the Noise Down.
Loud vehicles can be offensive. Ride as quietly as possible, don’t remove your spark arrester, and don’t modify the muffler or any other part of your air intake and exhaust systems. Such modifications not only increase noise, they also reduce engine performance and may be illegal.
• Choose Sensible Cleaners.
Use a biodegradable detergent when you wash your ATV. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Don’t throw cleaning solvents away; see the following guidelines for proper disposal.
• Recycle Wastes.
It’s illegal and thoughtless to put used engine oil in the trash, down a drain, or on the ground. Used oil, gasoline, and cleaning solvents contain poisons that can hurt refuse workers and contaminate our drinking water, lakes, rivers, and oceans. Before changing your oil, make sure you have the proper containers. Put oil and other toxic wastes in separate sealed containers and take them to a recycling center. Call your local or state office of public works or environmental services to find a recycling center in your area, and to get instructions on how to dispose of non-recyclable wastes.
202
Tips
Taking Care of the Unexpected
Taking Care of the Unexpected With all the challenges you can encounter off-road, there’s a chance that sometime something may go wrong. This section gives practical advice to help you deal with a wide range of problems. Take time to read this section before you ride. Also review the tips in Preparing for a Ride
General Guidelines ................................................................... 204
If Your Engine Quits or Won’t Start .......................................... 206
If You Have a Flat Tire............................................................... 209
If the High Coolant Temperature Indicator Lights ...................... 213
If a Fuse Blows.......................................................................... 215
If You Crash ............................................................................. 220
If You Lose Your Key ................................................................ 221
If the Battery Is Low (or Dead)................................................... 222
If a Component Fails................................................................. 223
Taking Care of the Unexpected
203
Taking Care of the Unexpected
General Guidelines
Keeping your ATV well-maintained is the best way to reduce the possibility of having a problem while riding. However, problems can arise even with well-maintained machines.
Remember to take along your owner’s manual, the tool kit that came with your ATV, and any other items (such as tire repair supplies and additional tools) that might help you solve a problem on your own.
If something goes wrong during a ride, the first thing to do is stop as soon as you safely can. Do not continue riding if you have a flat tire, or you hear an unusual noise, or your ATV just doesn’t feel right. If you continue riding, you could cause more damage and endanger your own safety.
After stopping, take time to assess the situation. Carefully inspect your ATV to identify the problem, then consider your options before you decide what to do.
If a problem is relatively minor and you have the tools, supplies, and skills to make a permanent repair, you may be able to fix it on the trail and continue riding. Or, you may be able to make a temporary repair that allows you to slowly ride back to your base where you can make a permanent repair or get help.
When a problem is more serious — or you don’t have the tools, supplies, experience, or time to deal with it — you need to choose the safest way to get yourself and your ATV back to base. For example, if you are close enough, you (or you and another person) might be able to push it back.
204
Taking Care of the Unexpected
Taking Care of the Unexpected
Should you ever have a problem while riding, please follow these guidelines:
• Always put personal safety first.
• Take time to assess the situation and your options before deciding what to do.
• If the problem is relatively minor and you have the tools, supplies, and skills to make a temporary repair, be sure to have permanent repairs made as soon as possible.
• Do not continue riding if you are hurt or your ATV is not in safe riding condition.
Additional recommendations for specific problems follow.
Taking Care of the Unexpected
205
If Your Engine Quits or Won’t
Start
Proper operation and maintenance can prevent starting and engine performance problems. In many cases, the cause of the problem may be a simple operational oversight.
If you have a problem starting the engine — or experience poor engine performance — the following information may help you. If you can’t correct the problem, see your dealer.
If your ATV won’t start, listen as you press the start/over ride button.
If you don’t hear the starter motor turning, refer to the Starter motor doesn’t operate symptom. If you can hear the starter motor working normally, refer to the
Starter motor works, but the engine won’t start
symptom.
206
Taking Care of the Unexpected
If Your Engine Quits or Won’t
Start
SYMPTOM: Starter motor doesn’t operate.
POSSIBLE CAUSE WHAT TO DO ignition switch OFF engine stop switch OFF
Turn the ignition switch ON.
Slide the engine stop switch to transmission not in neutral blown fuse
RUN.
Shift into neutral or squeeze the front brake lever.
Replace with a new fuse of the battery lead loose low (or dead) battery faulty starter motor
Tighten the battery lead.
Charge the battery (page 187).
If charging doesn’t help, see your dealer.
If all possible causes are negative, the starter motor may be faulty. See your dealer.
SYMPTOM: Starter motor works, but the engine won’t start.
POSSIBLE CAUSE out of fuel
WHAT TO DO
Fill the fuel tank.
flooded engine loose or unconnected spark plug cap
See Flooded Engine
Install the spark plug cap securely. If the engine still won’t start, see your dealer.
loose battery cables weak battery
Tighten the battery terminal bolts.
Charge the battery (page 187).
If charging doesn’t help, see your dealer.
Taking Care of the Unexpected
207
If Your Engine Quits or Won’t
Start
SYMPTOM: Engine starts, but runs poorly.
POSSIBLE CAUSE WHAT TO DO high coolant temperature
Check the coolant temperature gauge and high runs erratically, misfires blubbers (rich fuel mixture) sooty exhaust (rich fuel coolant temperature indicator.
Refer to If the High Coolant
Temperature Indicator Lights ,
See your dealer.
See your dealer.
See your dealer.
mixture) detonates or pings under load afterfires (backfires) pre-ignition (runs on after ignition switched
OFF)
If applicable, switch to the recommended octane gasoline
brand of gasoline. If the problem persists, see your dealer.
See your dealer.
See your dealer.
SYMPTOM: Engine starts, but runs poorly or dies when hot.
POSSIBLE CAUSE poor or inadequate
WHAT TO DO
See your dealer. fuel flow due to clogged fuel filter
(ensure clean fuel supply)
208
Taking Care of the Unexpected
If You Have a Flat Tire
How you handle a flat tire on the trail depends on how serious the tire damage is, and what tools and supplies you have with you.
If you have a slow leak or a minor puncture, use the plug method to make a temporary repair. (The plug method is applied from the outside of the tire and is the same as that for conventional tubeless tires.)
A plug-type repair kit, available at most auto parts stores or service stations, provides a plug, an installation tool, tire cement, and an instruction sheet. Follow the instructions provided with the repair kit to make a temporary repair.
As soon as possible, have the tire permanently repaired by your dealer. Any tire that cannot be repaired should be replaced.
Whenever the ATV is to be operated far from service facilities or available transportation, we recommend that you carry a tire pump and a repair kit with the vehicle.
If the leak is more serious, or a temporary repair doesn’t hold, the tire must be replaced. The tire will also need to be replaced if it is
damaged (page 180). Replacing a tire involves removing and re-
installing the wheel (page 211).
If you are unable to repair a flat tire on the trail, you will need to send for help. We strongly recommend that you do not try to ride with a flat tire. The ATV will be hard to handle, and if the tire comes off the rim, it may lock up the wheel and cause you to crash.
(cont’d)
Taking Care of the Unexpected
209
If You Have a Flat Tire
WARNING 3 WARNING
Riding your ATV with a temporary tire repair can be risky.
If the temporary repair fails, you can crash and be seriously injured or killed. If you must ride with a temporary tire repair, ride slowly and carefully until the tire is permanently repaired or replaced.
210
Taking Care of the Unexpected
If You Have a Flat Tire
Emergency Wheel Removal/Installation
Refer to Safety Precautions
(1)
(1)
(2)
(1) wheel nuts (2) wheel rim
Removal
1. Park your ATV on a firm, level surface.
2. Loosen — but do not remove — the wheel nuts (1).
3. Raise the front (or rear) wheels off the ground and place a support block under the vehicle.
4. Remove the wheel nuts.
5. Remove the wheel.
• Avoid getting grease, oil, or dirt on the front brake disc or pad surfaces when removing and installing each wheel. Any contamination can cause poor brake performance or rapid pad wear after reassembly.
(cont’d)
Taking Care of the Unexpected
211
If You Have a Flat Tire
Installation
1. Position the wheel.
2. Position each wheel nut so that the tapered side faces the wheel rim (2).
3. Hand-tighten the wheel nuts on the wheel, then lower the ATV to the ground before tightening the nuts in a crisscross (rather than circular) pattern to the specified torque:
47 lbf·ft (64 N·m, 6.5 kgf·m)
If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capability.
212
Taking Care of the Unexpected
If the High Coolant Temperature
Indicator Lights
Normally, the high coolant temperature indicator will only light momentarily when you turn the ignition to ON ( q ).
High coolant temperature may be caused by restriction of air flow to the radiator (such as mud caked on the radiator), extended idling, an oil leak, a coolant leak, a low oil level, a low coolant level, or extended operation under adverse conditions.
If the all segment of the coolant temperature gauge and high coolant temperature indicator are on while you’re riding, don’t ignore it. Pull safely to a stop. Stop the engine as soon as it’s safe to do so, and let it cool.
NOTICE
Continuing to ride with high coolant temperature or an overheated engine can cause serious engine damage.
• A steaming engine indicates a coolant leak. Shut the engine off and wait until the steaming stops. Look for a leak, but don’t touch the engine or radiator system. Let everything cool off first.
• Check for any restriction of air flow to the radiator.
• If there’s no obvious problem, leave the engine on so the fan and coolant circulating system can continue working. Monitor the coolant temperature gauge and high coolant temperature indicator. The indicator may turn off after a brief stop with no load on the engine.
• Check the radiator fan.
If the fan is not working, turn the engine off. Open the fuse box
(page 216) and check the radiator fan fuse. If the fuse is blown,
replace it with the proper (same rating) spare fuse. Start the engine. If the all segment of the coolant temperature gauge and high coolant temperature indicator stays on, turn the engine off.
If the radiator fan is working, visually check the coolant level in the reserve tank, located under the left front fender. It isn’t necessary to touch the radiator system.
(cont’d)
Taking Care of the Unexpected
213
If the High Coolant Temperature
Indicator Lights
• If the reserve tank is low or empty, don’t ride without adding
coolant (page 141). After adding coolant, turn the engine on and
check the coolant temperature gauge and high coolant temperature indicator.
If the indicator doesn’t turn off, do not ride. The engine needs repair.
Transport your ATV to your dealer (page 196).
If the temperature drops to normal, check the coolant level. If it has gone down, add more coolant.
• Check for an oil leak.
• Check the oil level. If necessary, add the recommended oil
(page 130) to the upper level mark. If you must leave your ATV to
get oil, secure it as much as possible.
• Start the engine, and check that the coolant temperature gauge and high coolant temperature indicator goes off.
If you are able to resume riding, continue to monitor the coolant temperature gauge and high coolant temperature indicator frequently.
If there is an oil leak — do not ride the ATV until the leak is repaired
If there’s a mild coolant leak, you can ride for awhile, carefully watching the coolant temperature gauge and indicator. Be prepared to stop and add more coolant or water. If the leak is bad, transport
your ATV to your dealer (page 196).
214
Taking Care of the Unexpected
If a Fuse Blows
All of the electrical circuits on your ATV have fuses to protect them from damage caused by excess current flow (short circuit or overload).
If something electrical on your ATV stops working, the first thing you should check for is a blown fuse (1).
Check all the fuses before looking elsewhere for another possible cause of the problem. Replace any blown fuses and check component operation.
(1)
(1)
(1) blown fuse
The main fuse and the circuit fuses are located under the rear fender cover.
The PS (Electric Power Steering) fuse is located under the rear fender cover.
Recommended Fuses main fuse 1 main fuse 2 other fuses
PS (Electric Power
Steering) fuse
40 A
10 A
20 A × 4, 10 A
40 A
(cont’d)
Taking Care of the Unexpected
215
If a Fuse Blows
Main Fuses Access
1. To prevent an accidental short circuit, turn the ignition switch to
OFF ( w ) before checking or replacing the fuses.
2. Remove the seat (page 120).
3. Remove the rear fender cover (page 121).
4. To access the main fuse 1 (2), remove the fuse cover (3).
5. To access the main fuse 2 (4), remove the fuse box cover (5).
UNDER REAR FENDER COVER
(3) (5)
(2)
(4)
(6)
(2) main fuse 1
(3) fuse cover
(4) main fuse 2
(5) fuse box cover
(6) spare fuse
6. Pull the main fuses out.
If the main fuse 1 is blown, install the spare fuse (page 119).
If the main fuse 2 is blown, install the spare fuse (6).
7. Install the fuse cover.
216
Taking Care of the Unexpected
Circuit Fuses Access
(7)
If a Fuse Blows
(8)
(7) circuit fuses (8) spare fuses
8. To check or replace a circuit fuse (7), pull the old fuse out of its retaining clips.
If the fuse is blown, replace it with a spare fuse (8) of the same rating.
If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating.
NOTICE
Replacing a fuse with one that has a higher rating greatly increases the chance of damage to the electrical system.
9. Install the fuse box cover.
10. Install the rear fender cover.
11. Install the seat.
(cont’d)
Taking Care of the Unexpected
217
If a Fuse Blows
PS (Electric Power Steering) Fuse Access
1. Turn the ignition switch to OFF ( w ) before checking the fuse.
2. Remove the seat (page 120).
3. Remove the rear fender cover (page 121).
4. To access the PS fuse (1), remove the fuse cover (2).
If the PS fuse is blown, install the spare fuse (page 119).
5. Install the fuse cover.
6. Install the rear fender cover.
7. Install the seat.
UNDER REAR FENDER COVER
(2)
(1) PS fuse
(1)
(2) fuse cover
218
Taking Care of the Unexpected
If a Fuse Blows
If you do not have a spare fuse and you cannot ride the ATV without fixing the problem, take a fuse of the same rating or a lower rating from one of the other circuits that you can do without temporarily.
If you replace a blown fuse with a spare fuse that has a lower rating, replace the fuse with the correct rating as soon as you can. Also remember to replace any spare fuses that were installed.
If the replacement fuse of the same rating burns out in a short time, there is probably a serious electrical problem on your ATV. Leave the blown fuse in that circuit and have your ATV checked by your dealer.
Taking Care of the Unexpected
219
If You Crash
Personal safety is your first priority after a crash. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. If you cannot ride safely, send someone for help. Do not ride if you will risk further injury.
If you decide you are capable of riding safely, carefully inspect your
ATV for damage and determine if it is safe to ride. Check the tightness of critical nuts and bolts securing such parts as the handlebar, control levers, brakes, and wheels.
If there is minor damage, or you are unsure about possible damage but decide to try riding the ATV back to your base, ride slowly and cautiously.
Sometimes, crash damage is hidden or not immediately apparent.
When you get home, thoroughly check your ATV and correct any problems you find. Also, be sure to have your dealer check the frame and suspension after any serious crash.
220
Taking Care of the Unexpected
If You Lose Your Key
Be sure to record your key number (1). Store the spare key and recorded key number in a safe location. You’ll need this number to have a duplicate key made.
If you lose your key and aren’t carrying a duplicate, either get your spare or have one made. If you don’t know your key number, call the dealer where you purchased your Honda ATV. They may have it listed in their records. If they don’t, transport your ATV to them or the nearest dealer. The dealer will probably have to remove the ignition switch assembly to find the key number so they can make a key for you.
(1) key number
(1)
Taking Care of the Unexpected
221
If the Battery Is Low (or Dead)
Jump starting is not recommended, especially if you use an automobile battery. The greater amperage of an automobile battery when the car engine is running can damage your ATV’s electrical system.
Bump starting is also not recommended.
If you can’t charge the battery or it appears unable to hold a charge, contact your dealer.
(Canada only)
Your ATV will operate even if the battery is low (or dead), as long as the engine is running. If the engine is not running, it may be started using the recoil starter.
1. Shift the shift lever in neutral position.
2. Apply the parking brake.
3. Turn the ignition switch to the ON ( q ) position.
4. Use the recoil starter (page 84) to start the engine.
222
Taking Care of the Unexpected
If a Component Fails
The brake levers or pedal, control cables, and other components can be damaged as you ride in dense brush or over rocky terrain. Making a trailside repair depends on how serious the damage is and what tools and supplies you have with you.
• If any component of the brake system is damaged, you may be able to ride carefully back to your base using the other brake components for slowing or stopping.
• If you damage a throttle cable or other critical component, your
ATV may be unsafe to ride. Carefully assess the damage and make any repairs that you can. But if there is any doubt, it’s best to be conservative and safe.
Taking Care of the Unexpected
223
BLANK PAGE
224
Taking Care of the Unexpected
Technical Information
Technical Information This section contains dimensions, capacities, and other technical data, plus information on government requirements and how to break-in your ATV.
Vehicle Identification ................................................................ 226
Specifications ........................................................................... 228
Break-in Guidelines................................................................... 233
Emission Control Systems ......................................................... 234
Oxygenated Fuels ..................................................................... 238
Technical Information
225
Vehicle Identification
Serial Numbers
The VIN and engine serial number may be required when ordering
replacement parts. You may record these numbers in the Quick
Reference section at the rear of this manual.
The VIN (1) is stamped on the front of the frame.
Remove the radiator cap lid (page 142).
FRONT
(1)
(1) VIN
The engine number (2) is stamped on the upper side of the rear crankcase.
REAR
(2)
(2) engine number
226
Technical Information
Vehicle Identification
Color Label & Code
The color label (1) is attached on the left side of the frame.
The color code is helpful when ordering replacement parts. You may record the color and code in the Quick Reference section at the rear of this manual.
LEFT SIDE
(1)
(1) color label
Technical Information
227
Specifications
Dimensions overall length overall width overall height wheelbase ground clearance
Fuel & Lubricants fuel recommendation fuel tank capacity fuel tank reserve engine oil capacity engine oil recommendation
84.5 in (2,147 mm)
47.4 in (1,205 mm)
48.6 in (1,235 mm)
50.9 in (1,292 mm)
9.4 in (239 mm) unleaded gasoline, pump octane number of 86 or higher
3.88 US gal (14.7 ℓ) including reserve
1.29 US gal (4.9 ℓ) after disassembly:
3.5 US qt (3.3 ℓ) after draining:
3.1 US qt (2.9 ℓ) after draining & oil filter change:
3.2 US qt (3.0 ℓ)
API Service Classification SG or higher except oils labeled as energy conserving or resource conserving on the circular API service label, SAE
10W-30, JASO T 903 standard MA,
Pro Honda GN4 4-stroke oil (USA &
Canada), or Honda 4-stroke oil, or an equivalent motorcycle oil
228
Technical Information
Specifications
Fuel & Lubricants (cont’d) cooling system Pro Honda HP Coolant or an recommendation equivalent high quality ethylene glycol antifreeze containing cooling system capacity corrosion protection inhibitors specifically recommended for use in aluminum engines
1.7 US qt (1.6 ℓ)
Capacities passenger capacity maximum weight capacity operator only
573 lb (260 kg) rider, all cargo and accessories
Engine Specifications displacement bore & stroke compression ratio spark plug
(standard) spark plug gap valve clearance
(cold) idle speed
29.0 cu-in (475 cm 3 )
3.62 × 2.81 in (92.0 × 71.5 mm)
9.5 : 1
BKR5E-11 (NGK) or
K16PR-U11 (DENSO)
0.039 – 0.043 in (1.00 – 1.10 mm) intake: exhaust:
0.006 in (0.15 mm)
0.009 in (0.23 mm)
1,400 ± 100 rpm
(NO ADJUSTMENT)
Technical Information
229
Specifications
Power Transmission primary reduction secondary reduction final reduction transmission ratio front rear
1st
2nd
3rd
4th
5th reverse final drive
Chassis & Suspension caster trail tire size, front tire size, rear tire pressure,
1°
-0.04 in (-1 mm)
AT25 × 8-12 11
AT25 × 10-12 11 front: front & rear (cold) 4.4 psi (30 kPa) rear:
4.4 psi (30 kPa)
MAXXIS MU25
MAXXIS MU26
2.103
1.875
3.231
3.154
4.230
2.388
1.608
1.178
0.848
5.743
shaft
230
Technical Information
Specifications
Electrical battery generator
Lights headlight assist headlight brake/tail light neutral indicator reverse indicator high coolant temperature indicator
PGM-FI indicator differential lock indicator
PS (Electric Power
Steering) indicator
Fuses main 1 main 2 other
PS (Electric Power
Steering)
GYZ16H
12 V – 16 Ah (10HR)
0.481 kW/5,000 rpm
12 V 35/35 W × 2
12 V 50 W
LED
LED
LED
LED
LED
LED
LED
40 A
10 A
20 A × 4, 10 A
40 A
Technical Information
231
Specifications
Torque Specification engine oil drain bolt engine oil filter cover bolts rear final gear oil drain bolt rear final gear oil fill cap front final gear oil drain bolt front final gear oil fill cap wheel nuts
18 lbf·ft (25 N·m, 2.5 kgf·m)
7 lbf·ft (10 N·m, 1.0 kgf·m)
9 lbf·ft (12 N·m, 1.2 kgf·m)
9 lbf·ft (12 N·m, 1.2 kgf·m)
9 lbf·ft (12 N·m, 1.2 kgf·m)
9 lbf·ft (12 N·m, 1.2 kgf·m)
47 lbf·ft (64 N·m, 6.5 kgf·m)
232
Technical Information
Break-in Guidelines
Help assure your ATV’s future reliability and performance by paying extra attention to how you ride during the first operating day or
15 miles (25 km).
During this period, avoid full-throttle starts, rapid acceleration, and constant rpm operation.
Technical Information
233
Emission Control Systems
Exhaust Emission Requirements
The U.S. Environmental Protection Agency (EPA), the California Air
Resources Board (CARB), and Environment Climate Change Canada
(ECCC) require that your ATV comply with applicable exhaust emissions standards during its useful life, when operated and maintained according to the instructions provided.
The Vehicle Emission Control Information Label (1) is attached on the left front of the frame.
(Canada only)
The Vehicle Emission Control Information Label (2) is attached on the left side of the frame.
LEFT FRONT LEFT SIDE
(1) (2)
(1) vehicle emission control information label
(2) vehicle emission control information label (Canada only)
234
Technical Information
Emission Control Systems
Source of Exhaust Emissions
The combustion process produces carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
Honda Motor Co., Ltd. utilizes various systems to reduce carbon monoxide, oxides of nitrogen and hydrocarbons.
Exhaust Emission Control System
The exhaust emission control system includes a PGM-FI system and oxygen sensor.
No adjustment to this system should be made although periodic inspection of the components is recommended.
The exhaust emission control system is separate from the crankcase emission control system.
Crankcase Emission Control System
The engine is equipped with a closed crankcase system to prevent discharging crankcase emissions into the atmosphere. Blow-by gas is returned to the combustion chamber through the air cleaner.
Technical Information
235
Emission Control Systems
Problems That May Affect ATV Exhaust Emissions
If you are aware of any of the following symptoms, have the vehicle inspected and repaired by your ATV dealer.
Symptoms:
1. Hard starting or stalling after starting
2. Rough idle
3. Misfiring or backfiring during acceleration
4. After-burning (backfiring)
5. Poor performance (driveability) and poor fuel economy
Federal regulations prohibit removing or disabling a device or element of design that may affect your engine’s emission performance unless your ATV will be used exclusively in competition.
If you modify your engine for use in sanctioned competition events, you must deface or destroy the emission control information label.
If you loan, sell, or give your competition modified Honda ATV to someone else, under applicable law, you must inform the new owner/operator in writing that the vehicle is to be used for competition only.
236
Technical Information
Emission Control Systems
Noise Emission Control System
TAMPERING WITH THE NOISE CONTROL SYSTEM IS PROHIBITED:
State laws prohibit, or Canadian provincial laws may prohibit, the following acts or the causing thereof: (1) The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use; or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE
THE FOLLOWING ACTS:
• Removal of, or puncturing the muffler, baffles, header pipes or any other component which conducts exhaust gases.
• Removal of, or puncturing of any part of the intake system.
• Lack of proper maintenance.
• Removing or disabling any emissions compliance component, or replacing any compliance component with a non-compliant component.
Fuel Permeation Emission Control System
This vehicle complies with the Fuel Permeation Emission Control regulations of the U.S. Environmental Protection Agency (EPA), the
California Air Resources Board (CARB), and Environment Climate
Change Canada (ECCC).
The fuel tank, fuel hoses, and fuel vapor charge hoses used on this vehicle incorporate fuel permeation control technologies.
Tampering with the fuel tank, fuel hoses, or fuel vapor charge hoses to reduce or defeat the effectiveness of the fuel permeation technologies is prohibited by federal regulations.
Technical Information
237
Oxygenated Fuels
Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the
United States and Canada use oxygenated fuels to help reduce emissions.
If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.
Before using an oxygenated fuel, try to confirm the fuel’s contents.
Some states/provinces require this information to be posted on the pump.
The following are the EPA-approved percentages of oxygenates for non-road vehicles:
ETHANOL (ethyl or grain alcohol) up to 10% by volume
You may use gasoline containing up to 10% ethanol by volume.
Gasoline containing ethanol may be marketed under the name
“Gasohol”.
Do not use gasoline containing more than 10% ethanol by volume.
The use of gasoline containing a higher percentage (e.g. E15, E20,
E85) of ethanol has not been approved for use in this vehicle and may cause starting and/or performance problems and can also damage metal, rubber, and plastic parts of the fuel system and are not be covered by the Distributor’s Limited Warranty.
238
Technical Information
Oxygenated Fuels
METHANOL (methyl or wood alcohol) up to 5% by Volume
You may use gasoline containing methanol containing up to 5% methanol by volume as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by volume may cause starting and/or performance problems. It may also damage metal, rubber, and plastic parts of your fuel system.
If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.
Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates mentioned above are not covered under warranty.
Oxygenated fuels can damage paint and plastic. Be careful not to spill fuel when filling the fuel tank. Wipe up any spills immediately.
NOTICE
Oxygenated fuels can damage paint and plastic. Damage caused by spilled fuel is not covered by warranty.
Technical Information
239
240
Technical Information
BLANK PAGE
Consumer Information
Consumer Information This section contains information on your warranty and how to get an official Honda service manual.
Authorized Manuals ................................................................. 242
Warranty Coverage .................................................................. 243
Warranty Service ...................................................................... 244
Contacting Honda .................................................................... 245
Your Honda Dealer ................................................................... 246
The Honda Rider’s Club (USA only) ........................................... 247
Consumer Information
241
Authorized Manuals
The Service Manual used by your authorized dealer is available from your Honda dealer or Helm, Inc. (USA only, Canada: See your dealer to order authorized manuals.)
Also available but not necessary to service your model is the Honda
Common Service Manual which explains theory of operation and basic service information for various systems on Honda motorcycles, scooters, ATVs, SxSs and PWCs.
The Winter Storage Guide in conjunction with the Owner's Manual and Service Manual can help you prepare your Honda motorcycle, scooter, ATV, and SxS for winter storage.
These Honda manuals are written for the professional technician, but most mechanically capable owners should find them easy to use if they have the proper tools and observe proper safety standards.
Special Honda tools are necessary for some procedures.
Publication Item No.
61HR404
61CSM00
S9507
31HR5630
Description
2018 TRX500FM1/FM2/FM5/FM6/FM7/
FE1/FE2/FA5/FA6/FA7
Service Manual
Common Service Manual
Winter Storage Guide
2018 TRX500FM6
Owner’s Manual
Order On-Line: www.helminc.com
Order Toll Free: 1-888-CYCLE93 (1-888-292-5393)
(NOTE: For Credit Card Orders Only)
Monday - Friday 8:00 AM - 6:00 PM EST
242
Consumer Information
Warranty Coverage
Your new Honda is covered by these warranties:
• TRX Limited Warranty
• Emission Control System Warranty
There are responsibilities, restrictions, and exclusions which apply to these warranties. Please read the Warranties Booklet given to you by your Honda dealer at the time of purchase. Be sure to keep your
Honda owner’s card with your Warranties Booklet.
Canada: Please refer to the Warranty Booklet posted on our website at www.honda.ca.
It is important to realize that your warranty applies to defects in material or workmanship of your Honda. Your warranty coverage does not apply to normal wear or deterioration associated with using the ATV.
Your warranty coverage will not be voided if you choose to perform your own maintenance. However, you should have the proper tools and service information, and be mechanically qualified. Failures that occur due directly to improper maintenance are not covered.
Almost all of your warranty coverage can be extended through the
Honda Protection Plan (USA only). For more information, see your dealer.
Consumer Information
243
Warranty Service
Please remember that recommended maintenance interval servicing is not included in your warranty coverage. Additionally, your warranty does not apply to the normal wear of items (such as brakes, tires, etc.).
If you believe you have a problem with your ATV, call the service department of your dealer. Make an appointment for an inspection and diagnosis. Remember, as the owner of the ATV, you will be asked to authorize that inspection. Your dealer will give you the results of the inspection. If the problem is covered under warranty, your dealer will perform the warranty repairs for you.
If you have questions about warranty coverage or the nature of the repair, it is best to talk to the Service Manager of your dealer.
Sometimes, in spite of the best intentions of all concerned, a misunderstanding may occur. If you aren’t satisfied with your dealer’s handling of the situation, we suggest you discuss your problem with the appropriate member of the dealership’s management team. If the problem has already been reviewed with the Service Manager, Parts Manager, Sales Manager, etc., contact the Owner of the dealership or their designated representative.
244
Consumer Information
Contacting Honda
Your owner’s manual was written to cover most of the questions you might ask about your Honda. Any questions not answered in the owner’s manual can be answered by your dealer. If your dealer doesn’t have the answer right away, they will get it for you.
If you have a difference of opinion with your dealer, please remember that each dealership is independently owned and operated. That’s why it’s important to work to resolve any differences at the dealership level.
If you wish to comment on your experiences with your Honda or with your dealer, please send your comments to the following address:
Motorcycle Division, American Honda Motor Co., Inc., P.O. Box
2200, Torrance, CA 90509-2200, mailstop: 100-4C-7B, telephone:
(866) 784-1870.
Canada: Honda Canada Inc., Customer Relations Dept, 180 Honda
Boulevard, Markham, Ontario L6C 0H9, telephone: (888) 946-6329, facsimile: (877) 939-0909.
E-mail: [email protected]
Please include the following information in your letter:
• name, address, and telephone number
• product model, year, and VIN
• date of purchase
• dealer name and address
We will likely ask your dealer to respond, or possibly acknowledge your comments directly.
Consumer Information
245
Your Honda Dealer
Once you purchase your new Honda, get familiar with the organization of your Honda dealer so you can utilize the full range of services available.
The service department is there to perform regular maintenance and unexpected repairs. It has the latest available service information from Honda. The service department will also handle warranty inspections and repairs.
The parts department offers Honda Genuine Parts, Pro Honda products, Honda Genuine Accessories (USA only), and Honda accessories and products (Canada only). The same quality that went into your Honda can be found in Honda Genuine replacement parts.
You’ll also find comparable quality in the accessories and products available from the parts department.
The sales department offers the Honda Protection Plan to extend almost all of your warranty coverage (USA only).
Your Honda dealer can inform you about competition and other riding events in your area. You’ll also find that your dealer is a source of information about safety training available in your local area and the Honda Rider’s Club of America (USA only).
We’re sure you’ll be as pleased with the service your Honda dealer continues to provide after the sale as you are with the quality and dependability of your Honda.
246
Consumer Information
The Honda Rider’s Club (USA only)
The Honda Rider’s Club of America (HRCA) sponsors local riding chapters at Authorized Honda Dealerships across the country.
Consumer Information
247
Index
Index
A
accessories .................................................................................68
accessory socket .........................................................................49
age recommendation .................................................................59
air cleaner,
dust cover .............................................................................152
filter ......................................................................................148
housing drain tube ................................................................153
air pressure,
gauge ....................................................................................119
tire ........................................................................................175
American Honda, contacting ....................................................245
apparel, protective ......................................................................56
appearance care .......................................................................188
authorized manuals ..................................................................242
B
bank angle sensor ignition cut-off system ...................................81
battery .....................................................................................183
brake light switch adjustment ...................................................173
brakes,
cable .....................................................................................172
fluid ......................................................................................166
front brake lever ......................................................................44
pad wear ...............................................................................169
parking ....................................................................................45
rear brake lever freeplay ........................................................171
rear brake lever/parking brake lever .........................................44
rear brake pedal ......................................................................44
braking .......................................................................................89
break-in guidelines ...................................................................233
248
Index
Index button,
mode select .................................................................14, 19, 20
start/over ride ..........................................................................39
C
capacity, fuel ............................................................................125
care, appearance ......................................................................188
cargo,
loading and operational guidelines ..........................................67
weight limit .............................................................................66
cleaning, appearance care ........................................................188
climbing hills ..............................................................................93
clip ...........................................................................................123
clutch system ............................................................................156
color label ................................................................................227
compartment,
owner’s manual .....................................................................119
tool kit ..................................................................................118
component fails ........................................................................223
consumer information ..............................................................241
controls & features .....................................................................34
coolant temperature gauge ........................................................28
crash, if you ..............................................................................220
crossing or turning on hills or slopes ...........................................98
customer service .......................................................................245
Index
249
Index
D
differential lock switch ................................................................36
digital clock ................................................................................26
dimmer switch, headlight ...........................................................41
dipstick .....................................................................................130
display check ..............................................................................16
display, multi-function ................................................................20
drivetrain boots ........................................................................182
E
electric power steering (PS) .........................................................54
emission control systems ..........................................................234
engine,
flooded ...................................................................................80
guard ....................................................................................181
number .................................................................................226
oil ..........................................................................................127
pinging ..................................................................................124
starting ....................................................................................78
stop switch ..............................................................................40
stopping ..................................................................................83
won’t start ............................................................................206
environment .............................................................................202
exhaust system,
cleaning ..................................................................................62
purging .................................................................................162
F
flag pole bracket ........................................................................47
flat tire .....................................................................................209
flooded engine ...........................................................................81
front boot guards .....................................................................181
front differential lock ..................................................................36
250
Index
Index
front driveshaft boots ...............................................................182
front driveshaft guards .............................................................181
front final gear oil .....................................................................138
fuel,
fill cap ...................................................................................125
gauge ......................................................................................24
oxygenated ...........................................................................238
recommendation ...................................................................124
refueling ................................................................................125
reserve fuel supply .................................................................125
tank capacity .........................................................................125
fuses ........................................................................................215
G
gap, spark plug ................................................................158, 229
gasohol ....................................................................................238
gasoline ....................................................................................124
gear shifting ...............................................................................85
guards ......................................................................................181
H
headlight dimmer switch ............................................................41
headlight switch .........................................................................41
high coolant temperature indicator ...............................14, 17, 213
hills,
crossing or turning on slopes ...................................................99
riding down hills ......................................................................98
riding up hills ...........................................................................94
stopping on hills ......................................................................96
Honda service manual ..............................................................242
Index
251
Index
Honda,
contacting .............................................................................245
dealer ....................................................................................246
Rider’s Club ...........................................................................247
hourmeter ..................................................................................30
I
identification, vehicle ................................................................226
ignition switch ............................................................................34
indicators,
4WD indicator .............................................................18, 20, 35
differential lock indicator .............................................14, 17, 36
gear position indicator .......................................................18, 23
high coolant temperature indicator ............................14, 17, 213
maintenance minder indicator ...........................................20, 31
neutral indicator ................................................................14, 17
PGM-FI indicator ................................................................14, 17
PS (Electric Power Steering) indicator ..................................14, 18
reverse indicator ................................................................14, 17
inspection, pre-ride .....................................................................61
K key,
lost ........................................................................................221
number .................................................................................221
kit, tool ....................................................................................118
L
labels, safety .................................................................................5
lamp check .................................................................................15
limit, weight ...............................................................................66
load limits ...................................................................................66
loading guidelines ......................................................................67
252
Index
Index lubrication,
engine oil ..............................................................................127
front final gear oil ..................................................................138
rear final gear oil ...................................................................136
M maintenance,
component locations .............................................................115
hourmeter ...............................................................................31
importance ............................................................................107
minder indicator ................................................................20, 31
precautions ...........................................................................109
record ...................................................................................114
safety ....................................................................................108
schedule ................................................................................110
tripmeter .................................................................................31
manual, service .........................................................................242
maximum weight limit ................................................................66
modifications ..............................................................................69
multi-function display .................................................................20
N
neutral indicator ...................................................................14, 17
noise emission control system ...................................................237
numbers, serial .........................................................................226
O
obstacles, riding over ................................................................101
odometer ...................................................................................27
oil,
engine ...................................................................................127
front final gear ......................................................................138
rear final gear ........................................................................136
Index
253
Index
operation component locations ..................................................11
owner’s manual storage ...........................................................119
oxygenated fuels ......................................................................238
P
parking .....................................................................................104
parking brake/reverse lever (P/R lever) .........................................45
passengers, no carrying ..............................................................59
pavement, no riding on ..............................................................73
pinging, engine ........................................................................124
plug, spark ...............................................................................158
pre-ride inspection ......................................................................61
problems, unexpected ..............................................................204
propeller shaft boots & yoke joint boot .....................................182
protective apparel .......................................................................56
PS (Electric Power Steering)..........................................................54
R
rear driveshaft boots .................................................................182
rear driveshaft guards ...............................................................181
rear fender cover removal .........................................................121
rear final gear oil ......................................................................136
recoil starter (Canada only) ...................................................42, 84
removal,
rear fender cover ...................................................................121
seat .......................................................................................120
tank cover assembly ..............................................................122
reverse,
assist cable ............................................................................157
assist lever .............................................................................157
gear, shifting into ....................................................................86
indicator ............................................................................14, 17
riding in ...................................................................................87
254
Index
Index
rider training ..............................................................................58
Rider’s Club Honda ...................................................................247
riding,
basic operation ........................................................................71
clothing ...................................................................................56
over obstacles ........................................................................101
precautions .............................................................................73
preparing for .........................................................................194
safety ........................................................................................2
safety precautions ...................................................................73
through water .......................................................................102
S safety,
important precautions ...........................................................109
labels .........................................................................................5
riding precautions ....................................................................73
schedule, maintenance .............................................................110
seat removal .............................................................................120
serial numbers ..........................................................................226
service,
customer ...............................................................................245
manuals ................................................................................242
warranty ................................................................................244
shifting gears ..............................................................................85
skidding or sliding ......................................................................93
spark arrester ...........................................................................162
spark knock ..............................................................................124
spark plug ................................................................................158
specifications ............................................................................228
speed limiter over-ride ................................................................36
speedometer ........................................................................18, 20
stalled engine .............................................................................82
Index
255
Index
stalling on a hill ..........................................................................95
start/over ride button ..................................................................39
starting, engine .....................................................................................78
troubleshooting .....................................................................206
stop switch, engine ....................................................................40
stopping engine .........................................................................83
storage,
ATV .......................................................................................198
owner’s manual .....................................................................119
suspension,
adjustment ............................................................................163
spring pre-load ......................................................................164
switch,
4WD .......................................................................................35
differential lock .......................................................................36
engine stop .............................................................................40
headlight .................................................................................41
headlight dimmer ....................................................................41
ignition ....................................................................................34
T
tank cover assembly removal ....................................................122
throttle,
tires,
air pressure ............................................................................175
flat ........................................................................................209
repairing ................................................................................179
replacing ...............................................................................180
thread conditions ..........................................................177, 178
tool kit .....................................................................................118
256
Index
Index
trailer hitch .................................................................................48
trailer towing,
operational guidelines .............................................................67
weight limits ............................................................................66
training, rider .............................................................................58
transporting your ATV ..............................................................196
tripmeter ....................................................................................27
trouble, unexpected .................................................................203
troubleshooting, starting ..........................................................206
turning,
on hills or slopes ......................................................................99
on level ground .......................................................................91
U
utility box ...................................................................................51
utility pocket ..............................................................................52
V
valve clearance .........................................................................161
vehicle identification no. (VIN) ..................................................226
W
warning labels ..............................................................................5
warranty,
coverage ...............................................................................243
extended ...............................................................................243
service ...................................................................................244
washing your ATV ....................................................................189
water,
riding through .......................................................................102
weight limit ................................................................................66
wheel removal ..........................................................................211
Index
257
Quick Reference
Quick Reference The following is a brief, but important collection of information you need to know about your Honda. You’ll also find space to record important notes.
How To Avoid Costly Repairs
The engine of your Honda can be the most expensive component to repair. Proper maintenance, especially the use of the recommended fluids and filters, prevents premature wear and damage.
Frequent causes of costly repairs are:
• Engine oil — insufficient quantity, improper oil.
• Air cleaner — dirty, leaking because of improper installation
(poor seal).
Record important information on the following page:
Quick Reference
Engine No.
VIN
Color Label
Owner’s Name
Address
City/State
Phone
Dealer’s Name
Address
City/State
Phone
Service Mgr.
Quick Reference
Quick Reference
Quick Reference
Scheduled
Maintenance
Pre-ride
Inspection
Fuel/Capacity
Engine Oil/
Capacity
Maximum
Weight Capacity
Initial: 100 miles (150 km)
Regular: every 600 miles (1,000 km)
Check the following items each time
before you ride (page 61): engine oil,
radiator coolant, fuel, tires, drivetrain boots, guards, nuts & bolts, underbody & exhaust system, air cleaner housing drain tube, leaks, loose parts, cables, lights, throttle, brakes, reverse assist lever, switches, steering.
unleaded gasoline, pump octane number
86 or higher
3.88 US gal (14.7 ℓ) reserve:
1.29 US gal (4.9 ℓ)
API Service Classification SG or higher except oils labeled as energy conserving or resource conserving on the circular API service label, SAE 10W-30, JASO T 903 standard MA, Pro Honda GN4 4-stroke oil or equivalent after draining:
3.1 US qt (2.9 ℓ) after draining & oil filter change:
3.2 US qt (3.0 ℓ)
573 lb (260 kg) rider, all cargo and accessories
Quick Reference
Tires
Tire Pressure
(cold)
Spark Plugs
Coolant
Fuses
Quick Reference
Front:
Rear:
Front:
Rear:
AT25 × 8-12 11
MAXXIS MU25
AT25 × 10-12 11
MAXXIS MU26
4.4 psi
(30 kPa)
4.4 psi
(30 kPa) standard:
BKR5E-11 (NGK) or
K16PR-U11 (DENSO) ethylene glycol antifreeze (silicate-free) for aluminum engines in 50/50 solution with
Pro Honda HP Coolant or an equivalent distilled water main 1: main 2: other:
40 A
10 A
20 A × 4, 10 A
PS (Electric Power Steering) 40 A
Quick Reference
Quick Reference
These symbols are used in Controls & Features section:
SYMBOL q w e r y t u i
COMPONENT
ON — ignition switch
OFF — ignition switch
4WD switch differential lock switch differential lock indicator — lights when the front differential lock mode engages start/over ride button
RUN — engine stop switch
OFF — engine stop switch
ON — headlight switch
OFF — headlight switch
HI — headlight dimmer switch
LO — headlight dimmer switch
Parking Brake/Reverse Lever
(P/R lever):
P — parking brake
R — riding in reverse
SEE PAGE
Quick Reference
advertisement
Related manuals
advertisement
Table of contents
- 1 Contents
- 8 ATV Safety
- 16 Instruments & Controls
- 62 Before Riding
- 78 Basic Operation & Riding
- 112 Servicing Your Honda
- 200 Tips
- 210 Taking Care of the Unexpected
- 232 Technical Information
- 248 Consumer Information
- 255 Index
- 265 Quick Reference