#58401E
110-120V~60Hz, 2.4A
4006936
TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
Tel: 1-855-838-3888 [email protected]
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit www.bestway-service.com
FLOWCLEAR
TM
Sand Filter
OWNER’S MANUAL
www.bestway-global.com
www.bestway-service.com
S-S-004028
2
S-S-004028
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING -
TO REDUCE THE RISK OF INJURY do not permit children to use this product unless they are closely supervised at all times.
WARNING -
RISK OF ELECTRIC SHOCK Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of the plug is needed, use only identical replacement parts.
WARNING -
The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI,push the test button. The
GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a qualified service representative before using.
CAUTION -
To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
WARNING -
To reduce the risk of electric shock, replace damaged cord immediately.
WARNING -
To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION:
This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
•THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
• CAUTION:
TO ENSURE CONTINUED PROTECTION AGAINST SHOCK HAZARD,USE ONLY IDENTICAL
REPLACEMENT PARTS WHEN SERVICING.
• WARNING:
RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A GROUNDING TYPE RECEPTACLE.
• CAUTION:
THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED
POOLS.
• CAUTION:
CONNECT ONLY TO GROUNDING TYPE RECEPTACLE PROTECTED BY A CLASS A GROUND FAULT
CIRCUIT INTERRUPTER.
• CAUTION:
FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC SHOCK THIS UNIT IS TO BE MOUNTED
TO THE BASE IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
• WARNING -
RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin.
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground.
4) Do Not Touch Plug With Wet Hands.
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
3
S-S-004028
CONTROL VALVE
OVERVIEW
WARNING:
To prevent equipment damage and possible injury, always switch off the sand filter before changing the Control Valve function.
Changing valve positions while the pump is running can damage the Control Valve, which may cause personal injury or property damage.
How to Use the Control Valve:
Press down on the Control Valve handle and rotate to desired function.
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter functions: Filter, Rinse, Circulate, Backwash,
Closed and Drain.
Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool.
Backwash: This function is used to clean the sand bed; water is pumped down through the Collector Hub, upwards through the sand bed, and deposited out of Port D.
Rinse: This function for initial startup, cleaning, and sand bed leveling after
Backwash; water is pumped downwards through the sand bed, up through the
Collector Hub and deposited out of the valve Port D.
Circulate: This function circulates pool water bypassing the sand filter; use this function if the filter is broken to collect debris in the Debris Screens.
23
SPECIFICATIONS
348mm
27
568mm
Drain: This function drains water from the pool; another filter bypass setting, water is pumped and deposited out of Port D, instead of returning it to the pool.
PARTS REFERENCE OVERVIEW
Before assembling the sand filter, take a few minutes to become familiar with all the sand filter parts.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
12
18
12
20
21
22
23
24
23
REF.NO.
21
22
23
24
26
15
16
17
18
19
20
11
12
13
14
1
2
3
4
5
6
7
8
9
10
DESCRIPTION
Control Valve
Pressure Gauge
Top Flange Clamp
Top Tank
Hub
Flange Clamp
O-ring
Bottom Tank
Drain Washer
Drain Valve Cap
Garden Hose Adapter
Washer
Port D Cap
O-ring
Piping
Strainer Cover
Strainer
Seal Ring
Pump
Adapter Nut
Hose Adapter
O-ring
Hose Clamps
Hose( Ø32mm 1.5M
)
GFCI
QTY.
SPARE PART NO.
2
2
5
2
1
1
1
2
1
1
1
1
1
5
1
1
1
1
1
1
1
1
P6905
P6581
P6580
P6614
P6029
P6540
P6149
P6560
P6561
P6562
1 P6563
1
3
P6848
P6615
P61140
P61138
P6553
P6620
P6621
P6622
P6623
P6618
P6005
P6124
P61139
P6783
19 26
23
22
28
(P6680) (P61318)
23
25
27 23
Filter Diameter:
Effective Filter Area:
Max. Operating Pressure:
Working sand filter pressure:
Max. Water Temperature :
Sand:
Sand Size:
Sand Capacity:
27
28
20
21
Optional Parts
22
23
O-ring
Hose Clamps
25
Debris Screen
Debris Screen piping
T-joint
Adapter Nut
Hose Adapter
348m m
0.095m
2 (1.02ft
2 )
0.84Bar (12PSI)
< 0.45Bar (6.5PSI)
35° C
Not included
#20 silica sand, 0.45-0.85mm
Approximately 18 kg
1
3
3
2
2
2
6
6
P6005
P6124
P6680
P61318
P6132
P6362
P6615
P6618
Closed: This function stops water flowing between the sand filter and the pool.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
GFCI Test
A
RESET
TEST
B
RESET
TEST
C
RESET
TEST
D
A. To test the GFCI plug, insert it into a grounding type receptacle.
B. Press the “RESET” button; the indicator turns red.
NOTE:
If the indicator light is not on, the test has failed.
C. Press the “TEST” button. The indicator turns off.
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales Service.
4
S-S-004028
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф3.8cm)
21 20
23
Pool Pool
1.
Connect the Hose Adaptor (21) with Adapter Nut (20) to both two ends of the hoses and tighten with the hose clamps (23).
2.
Attach the Hoses to the Sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position.
3.
Attach the Hoses to the connection valves on the pool. Ensure the corresponding letters on both the pool and the Sand filter match (A to A, B to B).
GARDEN HOSE ADAPTOR FUNCTIONS
1
1.
Assemble the garden hose adaptor.
2.
Screw the garden hose adaptor onto port D of the sand filter.
3.
Attach garden hose to the garden hose adaptor.
2 3
NOTE:
1.
Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2.
Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3.
Ensure the washer is in position before assembling the garden hose adaptor.
110mm Section I: Assembly (You will need a Phillips screwdriver.)
1.
Carefully remove all components from the package and check to ensure nothing is damaged. If equipment is damaged,
immediately notify the retailer from where the equipment was purchased.
2.
The sand filter should be placed on solid, level ground, preferably a concrete slab. Position the sand filter so the Ports
and Control Valve are accessible for operation, servicing and winterizing.
3.
The sand filter must be vertically fixed on ground or a certain pedestal made of wood or concrete before use to prevent the
sand filter from accidentally falling. Fully assembled sand filter will exceed 18kg. The mounting holes should be 8mm in
diameter and spaced 110mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to
the pedestal.
Ø8mm
Load pool-grade filter sand
NOTE:
Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one 18kg bag should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, thereby voiding the warranty.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the collector Hub.
NOTE:
SAND NOT INCLUDED.
O-r ing Nut
Nut
MAX.
MIN .
1. Turn the nut counter clockwise to
release the flange clamp and remove
the Top Tank.
Nut
2. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. Do not pour the sand into the pipe of the Hub. #20 Silica sand 0.45-0.85mm, approximately 18kg.
5
3. Ensure the O-ring is in place on the rim of the Bottom
Tank, make sure the O-ring and the rim of the Bottom
Nut over the seam and turn the Nut clockwise to fasten it.
S-S-004028
C
C
C
C
O-ring
4. Attach the Control Valve to the Top
Tank, ensuring the O-ring is in place on the rim of the Top Tank. Make sure the
O-ring and the rim of the Top Tank are clean without nicks, tears, scrapes or sand, and that the vertical pipe of the
Hub is inserted into the base of the
Control Valve.
5. Make sure Port C on the Control Valve is aligned with Port C on the Pump. Attach the
Top Flange Clamp and screw into position.
6. Attach the Piping to Pump Port C and to
Control Valve Port C, screw the threaded
locking rings into position.
Make sure the Washer is properly positioned on both ends of the Piping.
Section II: Hose Configuration for Backwashing and
Rinsing
NOTE:
Ensure the Control Valve is set to the Closed function.Your pool should be filled with water, make certain all of the pool’s Debris
Screens (25) are fully submerged in water.
Please check if your product includes a T-Joint (28) (see Fig. E).If yes,assemble your sand filter referring to method A; if no, assemble your sandfilter referring to method B.
Method A(see Fig.A-1)
1.
Attach one end of the hose (24) to the sand filter’s Port B; screw the
threaded locking ring into position.
2.
Attach the T-joint(28) to the other end of the long hose (24).
3.
Attach one end of both the pipings (27) to the T-joint (28), and the other
Fig.E
end to the pool’s Outlet “B”. Tighten the Hose clamps (23) of the T-joint (28).
4.
Remove the Stopper Plug from the pool’s Outlet B and insert Debris
Screen (25) supplied with your kit.
5.
With the Hose and the Debris Screen (25) in position, secure and tighten the
Hose Clamp (23).
Method B(see Fig.B-1)
1.
Attach one Hose (24) to the sand filter’s Port B; screw the threaded locking ring
28
A
D
A
D
A
B
27
A
B
B
23
23
23
B
23
24
into position.
2.
Connect the other end of the Hose (24) to the pool’s Outlet B.
3.
Remove the Stopper Plug from the pool’s Outlet B and insert Debris Screen (25)
24
B
supplied with your kit.
4.
With the Hose and the Debris Screen in position, secure and tighten the Hose
Clamp (24).
NOTE:
It is important to ensure all elements: Hose, Debris Screen and pool outlet are properly aligned.
5.
Screw the other Hose to Port D; and place the opposite end in drain area.
6.
With the Hoses attached, you can proceed to fill the pool, refer to pool owner’s manual for filling instructions.
28
23
27
Fig.A-1
Fig.B-1
>1/2 in
>1/2 in
P61318
P61318
A
A
P6680
>1/2 in
P6680
>1/2 in
B
B
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION:
DO NOT DRY RUN THE SAND FILTER
1.
Press down on the Control Valve handle and rotate to the Backwash function.
2.
Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3.
Unplug the sand filter and set the Control Valve to the Rinse function.
4.
Insert the plug and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5.
Unplug the sand filter. Set the Control Valve to the Closed function.
6.
Top up pool water.
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Unplug the sand filter immediately if water levels near the pool’s Inlet and Outlet valves. DO NOT DRY RUN THE SAND FILTER.
6
S-S-004028
Section IV:
Complete Sand Filter Installation
Connect the Fourth Hose
NOTE:
It is imperative to check that the hydraulic connectors are not closed.
NOTE:
Ensure the Control Valve is set to the
Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig.E), and referring to B-2 if not. The assembly methods are the same.
1.
Detach the Hose from Port D.
2.
Attach the Hose(24) to the Control Valve’s Port A; screw
the threaded locking ring into position.
3.
Connect the other end of Hose(24) to the pool’s Inlet A.
4.
Remove the Stopper Plug from the pool’s Inlet A and
insert Debris Screen(25) supplied with your kit.
5.
With the Hose and the Debris Screen in position, secure and tighten the Hose Clamp(23).
NOTE:
It is important to ensure all elements:
Hose, Debris Screen and pool Inlet are properly aligned.
Fig.E
A
28
24
A
23
B
23
B
27
23
23
B
23
28
23
27
Fig.A-2
24
23
>1/2 in
P61318
A
>1/2 in
P6680
B
>1/2 in
P61318
A
>1/2 in
B
P6680
Fig.B-2
24
24
Section V:
Sand Filter Operation
1.
Now the sand filter is ready for use. Set the
Control Valve to the Filter function.
NOTE:
To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2.
Swith on the sand filter, press the “RESET”
button to run it.
NOTE:
The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on
Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.45Bar (6.5PSI) when it is running.
Sand Filter Maintenance
CAUTION:
You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the
Pressure Gauge is 0.45Bar (6.5PSI) or higher, or water flow to the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in
Section II and Section III: Backwash and Rinsing.
NOTE:
1.
The Pressure Gauge is just used for measuring the water pressure, not used for
precision measurement.
2.
We recommend you clean the sand bed once a month or less regularly depending
on how often the pool is used. Do not clean the sand too frequently.
Cleaning the Strainer
1.
Switch off the sand filter and set the Control
Valve to the Closed function.
2.
Replace the Debris Screens with Stopper
Plugs to prevent water from escaping.
3.
Remove the Strainer Cover by unscrewing it.
4.
Take out the Strainer, remove any debris.
5.
Put the Strainer back into position. Ensure
the hole in the strainer is aligned.
6.
Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Remove the Stopper Plugs and insert the Debris Screens
NOTE:
The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1.
Switch off the sand filter and set Control Valve to the Drain function.
2.
Detach the Hose from the connection valve’s Port A and sand filter Port A and
attach to Port D.
NOTE:
Remember to replace the Debris Screen with Stopper Plug to prevent water from escaping.
3.
Switch on the sand filter and press the “RESET” button to run the filter and remove
the pool water.
WARNING:
DO NOT DRY RUN THE SAND FILTER.
7
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty.
1.
Backwash the sand filter as previously outlined in Section II and Section III.
2.
Drain the pool according to the pool owner’s manual.
3.
Unscrew the drain valve cap at the bottom of the tank and release the remaining
water.
4.
Disconnect the two Hoses from the pool and the sand filter.
5.
Completely pour the sand out of the tank and dry all components.
6.
Store the sand filter in a dry location out of child’s reach.
S-S-004028
TROUBLESHOOTING
Problems
Sand Filter does not operate - GFCI broken
Probable Causes
Sand is flowing to the pool
- Sand is too small
- Move the control valve from the backwash to the filter
function without stop the sand filter
- The level of the sand is too high
- The skimmer is broken
Solutions
- Contact your local Bestway Aftersales Service point to get instructions
- Recommend 0.45mm to 0.85mm #20 silica sand
- Stop the sand filter every time set the control valve
- Check if the level of the sand is between the marked “MAX” and “ MIN” on the hub
- Replace the skimmer
No water flow
- Stopper plugs were not removed
- The control valve is set to Closed
- The strainer is blocked
- Sand filter broken
Excessive filter pressure
- Dirty filter
- Calcified sand bed
- Insufficient backwashing
- The pressure gauge is broken
Control Valve leaks from the port D
Connectors leaks
- Control Valve is set between two functions
- The gasket is broken
- Washer of the connectors not in place
- Washer of the connectors broken
- O-ring on the hose connection is broken
- Loose Hoses
- Remove the stopper plugs and insert the debris screens
- Set to filter function
- Clean the strainer
- Call for service
- Backwash
- Inspect sand and change if necessary
- Backwash until water runs clear
- Replace the pressure gauge
- Set to one function
- Replace the gasket
- Reposition the washer
- Replace the washer
- Replace the o-ring
- Tighten them
8
S-S-004028
Limited BESTWAY
®
Manufacturer’s Warranty
The product you have purchased comes with a limited warranty. Bestway ® stands behind our quality guarantee and assures, through a replacement warranty, your product will be free from manufacturer’s defects that result in leaks. If a Manufacturer defect is found within:360 days for the motor pumps from the original date of purchase for 30 days for hoses, fitting and accessories included in the package from the original data of purchase.
To enact a warranty claim, this form must be completed and supplied with a copy of your purchase receipt to your local Bestway After Sales Center.
Please contact your local Bestway After Sales Center before sending any documents, they will provide full instructions of what is needed for your claim.
Bestway ® is not responsible for economic loss due to water or chemical costs and Bestway ® will not replace any products deemed to have been damaged due to negligence or having been used outside of the owner’s manual guidelines.
Bestway’s warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within the user manual, this
parties. The product must be stored and handled in accordance with the warranty applies only to products which have not been modified by any 3 rd technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of incorrect voltage, excessive heat exposure, improper installation, improper wiring or testing, or improper storage.
Replacements and repairs don’t extend the duration of the warranty. The date to be considered as the start of the warranty is only the one shown in the original receipt/purchase invoice.
Please copy the Batch Number located on the body of the sand filter.
Batch
Number
/DD
Batch
Number
Batch
Number
Batch Number:
TO: BESTWAY ® SERVICE DEPARTMENT DATE:
Date of purchase receipt:
Customer Code Number:
FAX/E-MAIL/TEL: Please refer to your country according to the information you find on the back cover or on our website: www.bestway-service.com
Please provide your address details in full. Note: Incomplete address details will result in delayed shipments.
Bestway reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
REQUIRED INFORMATION -- PLEASE WRITE THE DELIVERY ADDRESS
Name: Address: Zip code:
Country:
Telephone:
Retailer:
City:
Fax:
Please Clearly Write Your Item Code:
Mobile:
E-mail:
Item Code
Batch
Number
SAND FILTER MODEL #XXXXXX
SAND FILTER WITH OZONATOR MODEL #XXXXXX
All drawings for illustration purpose only. Not to scale.
Description of problem
Water leaking
Stopped working
Item is incomplete, Which part is missing – Please put the code you find on the instruction manual
Others, please describe
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
Bestway reserves the right to request photographic evidence of defective parts, or to require the sending of the item for additional testing.
In order to best assist you, we request all information you provide is complete.
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE WWW.BESTWAY-SERVICE.COM.
VIDEOS ARE ALSO AVAILABLE ON OUR BESTWAY CHANNEL ON YOU TUBE: http://youtube.com/user/BestwayService.
9
S-S-004028
10
S-S-004028
11
S-S-004028
Authorized Service Centers
Albania
Phone: (+355) 682003429
Fax: (+386) 056621203
E-mail: [email protected]
Argentina
Phone: (+54) 1159843871
E-mail: [email protected]
Australia
Phone: (+61) 290371388
Fax: (+61) 297379423
E-mail: [email protected]
Austria
Phone: (+43) 720882434
Fax: (+43) 720882435
E-mail: [email protected]
Belgium
Phone: 0 800 20 132
Fax: (+32) 026104411
E-mail: [email protected]
Bosnia
Phone: (+387) 039670935
Fax: (+386) 056621203
E-mail: [email protected]
Brasil
Phone: 0800 001 8400
E-mail: [email protected]
Bulgaria
Phone: (+359) 879012892
Fax: (+359) 29250232
E-mail: [email protected]
Canada
Phone: 1 855 838 3888
Fax: 1 480 838 1888
E-mail: [email protected]
Chile
Phone: (+56) 2232036438
E-mail: [email protected]
Colombia
Phone: (+57) 13441717
E-mail: [email protected]
Croatia
Phone: (+385) 0997930168
Fax: (+386) 056621203
E-mail: [email protected]
Cyprus
Phone: (+357) 22 426803
(+357) 22 423824
Fax: (+357) 22 495137
E-mail: [email protected]
Czech Republic
Phone: (+420) 0387020573
E-mail: [email protected]
Denmark
Phone: (+45) 33321019
Fax: (+45) 33321036
E-mail: [email protected]
Finland
Phone: (+358) 504104403
E-mail: [email protected]
France
Phone: 0892707709 (0,34 TTC/MINUTE)
Fax: (+33) 0489069991
E-mail: [email protected]
Germany
Phone: (+49) 6946001281
Fax: (+49) 6946001282
E-mail: [email protected]
Greece
Phone: 00.800.391.275.300
Fax: (+39) 0291390361
E-mail: [email protected]
Hungary
Phone: (+36) 0640204624
E-mail: [email protected]
Iceland
Phone: (+46) 8 506 691 90
Fax: (+46) 506 690 99
E-mail: [email protected]
Ireland
Phone: 8006120457
Fax: (+44) 01626835736
E-mail: [email protected]
Italy
Phone: (+39) 0236265839
Fax: (+39) 0291390361
E-mail: [email protected]
Macedonia
Phone: (+389) 032386235
Fax: (+386) 056621203
E-mail: [email protected]
Malta
Phone: (+356) 27438201/21499101
Fax: (+356) 21496206
E-mail: [email protected]
Mexico
Phone: (+52) 5541693920
Fax: (+52) 8183463416
E-mail: [email protected]
Moldova
Phone: (+373) 68535552
E-mail: [email protected]
Netherlands
Phone: 8002378929
Fax: (+31) 887878969
E-mail: [email protected]
New Zealand
Phone: 0800 142 101
E-mail: [email protected]
Norway
Phone: (+47) 22650122
Fax: (+47) 22721127
E-mail: [email protected]
Peru
Phone: (+51) 17089795
E-mail: [email protected]
Poland
Phone: (+48) 327505320 / 322326040
Fax: (+48) 327505330
E-mail: [email protected]
Portugal
Phone: (+351) 707506692
Fax: (+34) 902602705
E-mail: [email protected]
Romania
Phone: (+40) 212525354 / 213362858
Fax: (+40) 212525353 / 213362854
E-mail: [email protected]
Russia ( Россия )
Phone: +7 (495) 978-90-88
E-mail: [email protected]
Serbia and Montenegro
Phone: (+381) 0656644962
(+386) 056621206
Fax: (+386) 056621203
E-mail: [email protected]
Slovak Republic
Phone: (+421) 0415078833
Fax: (+421) 0415078808
E-mail: [email protected]
Slovenia
Phone: (+386) 056621206
Fax: (+386) 056621203
E-mail: [email protected]
South Africa
Phone: (+27)-21-5771401
Toll-Free ： 0800 224 881
Fax: (+27)-21-5774400
E-mail: [email protected]
Spain
Phone: (+34) 902351045
Fax: (+34) 902602705
E-mail: [email protected]
Sweden
Phone: (+46) 8 506 691 90
Fax: (+46) 506 690 99
E-mail: [email protected]
Switzerland
Phone: (+41)(0)719290000
Fax: (+41)(0)719290090
E-mail: [email protected]
Turkey
Phone: (+90) 02126444600
Fax: (+90) 02125550224
E-mail: [email protected] [email protected]
Ukraine
Phone: (+38) 0577597227
(+38) 0677033206
E-mail: [email protected]
United Kingdom
Phone: 08455760116
Fax: (+44) 01626835736
E-mail: [email protected]
USA
Phone: 1 855 838 3888
Fax: 1 480 838 1888
E-mail: [email protected]
S-S-004028
