AWA JTM2792 Operating Instructions Manual

Add to My manuals
31 Pages

advertisement

AWA JTM2792 Operating Instructions Manual | Manualzz

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

PACKAGE CONTENTS

CONTROL BUTTONS AND TERMINALS

FRONT PANEL

REAR PANEL

REMOTE CONTROL

BASIC CONNECTIONS

BATTERY INSTALLATION

CONNECTING POWER CORD

CONNECTING THE AERIAL CABLE

CONNECTING TO SCART CONNECTOR

CONNECTING TO COMPONENT VIDEO TERMINAL

CONNECTING TO COMPOSITE VIDEO TERMINALS

CONNECTING TO S- VIDEO TERMINAL

CONNECTING TO DVI INPUT CONNECTOR

CONNECTING TO A PC

CONNECTING TO A HEADPHONE

BASIC OPERATION

SWITCHING THE LCD TV ON/OFF

ADJUSTING THE VOLUME

USING MUTE

USING MENU

SELECTING ON SCREEN LANGUAGE

CHOOSING A TV CHANNEL

SELECTING INPUT SOURCE

PICTURE MENU

SOUND MENU

SET UP MENU

TV MODE

SCART 、 VIDEO AND S-VIDEO MODE

YPBPR MODE

VGA MODE

DVI MODE

1

19

20

20

20

22

23

24

25

9

12

13

13

14

15

16

9

10

10

11

17

17

17

17

17

18

18

18

3

5

6

6

7

8

TABLE OF CONTENTS

TIMER MENU

FUNCTION MENU

TELETEXT FUNCTIONS(OPTION)

Display Teletext

Page Selection

HOLD

INDEX

Enlarging Text

Reveal Mode

MIX Mode

SUBPAGE

COLOR buttons (RED, GREEN, YELLOW, CYAN)

SUPPORTED OPERATING MODES

TROUBLESHOOTING

SPECIFICATIONS

26

27

29

30

31

28

28

28

28

28

28

28

28

28

28

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT

OPEN

TO REDUCE THE RISK OF

ELECTRIC SHOCK .

DO NOT REMOVE COVER .

NO USER-SERVICEABLE

PARTS INSIDE. REFER

SERVICING TO QUALIFIED

SERVICE PERSONNEL.

This symbol indicates

“dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Read this Manual

Read this manual throughly before operating the unit .

Keep this manual

Keep this manual for future reference

.

Observe all warnings

All warnings on the product and in the manual must be observed closely

.

Follow all instructions

All operating instructions in the manual must be followed .

Do not insert liquids or objects

Li quids or objects could result in fire or electrical shock

.

Use special caution in households where children are present

.

If liquids or objects should enter the LCD TV

, immediately turn off the power switch

, disconnect the power plug from the AC outlet and contact the qualified service personnel

.

● Do not place the LCD TV near the bathtub, bathroom

, kitchen sink

,

wet basement or swimming

pool , and the like .

● Do not expose the LCD TV to rain or moisture .

● Do not place flower vases, pots

,

cups

, cosmetics

, liquids as water, etc on or around the LCD TV

.

● Do not place metals, combustibles

, etc on or around the LCD TV.

● Do not drip or splash liquid of any kind on the LCD TV

.

Do not give the LCD TV any shock or impact

If the LCD TV should be shocked and/or broken , it could result in an injury , and continued use could result in fir or electrical shock .

If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the AC power outlet and contact the qualified service personnel

.

Prevent the unit from falling

● Fasten the LCD TV to a wall using a cord or chain which is sufficient to support the weight of the

LCD TV

.

Before moving the LCD TV, the cord or chain should be removed

.

● Avoid children to climb on the LCD TV

.

● Do not place the LCD TV on a bed, sofa, rug

, similar surface. Do not place the LCD TV on an un-

stable cart, stand, or table. The LCD TV may fall , causing serious damage to the LCD TV and/or

serious personal injury, death

.

● When the product is used on a trolley, care should be taken to avoid quick stops, excessive force,

and uneven surfaces that may cause the product and trolley to overturn.

3

IMPORTANT SAFETY INSTRUCTIONS

Do not block any ventilation openings

● The vents and other openings in the cabinet are designed to let hot air escape from the LCD TV.

Do not cover or block these vent s and openings since insufficient ventilation can cause over-

heating. Do not place the LCD TV on a bed, sofa, rug or other similar surface, since they can block ventilation openings, it may overheating and result in fire.

● Do not cover the LCD TV with cloth, such as curtains, or items such as news paper, etc.

● This unit is not designed for built-in installation, do not place the product in an enclosed place such

as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are

followed.

Avoid high temperature environment

The heat could adverse influence on the LCD TV and other parts, and could result transmutation, melting or fire.

● Do not place the LCD TV, the remote control and other parts in direct sunlight or near a hot object

such as heater, etc.

● Do not put the LCD TV in a place where the temperature is widely changing.

Avoid oils

Do not install the LCD TV in a place that use oil. Dust absorbing oil may enter into the unit and damage the unit .

Power cord protection

Incorrect connection of the power cord could result in fire or electrical shock .

● Do not connect too many appliances to the same mains socket as this could result in fire or electrical

shock .

● The apparatus shall be connected to a mains socket outlet with a protective earthing connection .

● The socket outlet for connecting mains plug shall be easily accessible and remain readily operable.

● Do not overload wall outlet as this can result in fire or electrical shock.

● Check that the connecting portion of the AC power cord is clean (with no dust), before using. Use a

soft and dry cloth to clean the power plug.

● AC power cord should be routed so that they are not likely to be walked on or pinched by items

placed upon or against it. Also do not put any heavy on the AC power cord .

● Do not touch the AC power cord with a wet hand .

● Pull out the AC power cord by the plug. Do not pull on the power cord .

● Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.

● Do not pinch, bend, or twist the cable excessively. The core lines may be bared or cut, causing a

short circuit which may induce fire or electrical shock .

● For your own safety, do not touch any part of the unit, power cord or aerial lead during lightning

storms .

● Do not modify the AC power cord .

● Disconnect the power cord if the LCD TV is not used for a long time.

● Switch off and with draw the power plug before making or changing connections.

Handing and cleaning the screen surface of display unit

To avoid screen degradation, follow the points me mentioned below. Do not push on or scratch with hard objects, or throw anything at the screen.

The screen may be damaged.

● Be sure to unplug the power cord from outlet before cleaning.

● Do not touch the display panel after operating continuously for a long period as the display panel

becomes hot.

● We recommend that the screen surface is touched as little as possible.

● To remove dust from the screen surface, wipe gently with a clean, soft and cotton-free dry cloth.

● Do not use any type of abrasive pad, alkaline/acid cleaner or strong solvent such as alcohol, thinner

or benzene etc, as the surface may be impaired.

Cleaning the cabinet

● Be sure to unplug the power cord from the outlet before cleaning.

● Clean the cabinet with a soft cloth.

● Note that material deterioration or screen coating degradation may occur if the display unit is ex-

posed to a volatile solvent, such as alcohol, thinner, benzine or insecticide, or if prolonged contact

is maintained with rubber or vinyl materials.

4

IMPORTANT SAFETY INSTRUCTIONS

Carrying and moving

● Be sure to always carry the LCD TV by two people holding it with two hands, one hand on each

side of the LCD TV. If you carry the unit in a manner other than that specified, it may drop and a

serious injury may be caused.

Servicing

Do not open the cabinet or remove the rear cover of the unit. If any of the following conditions occurs, unplug the AC power cord from the AC outlet, and contact a qualified service personnel.

● When the power cord or plug is damaged.

● When the LCD panel is damaged.

● When the liquid is spilled on the unit or when objects have fallen into the unit.

● When the unit has been exposed to rain or water.

● If the unit has been dropped or the cabinet has been damaged in any way.

● If the unit does not work properly even after you have refer to the

TROUBLESHOOTING

section.

Replacement parts

● In case the unit needs replacement parts, make sure that the service personnel uses replacement

parts specified by the manufacturer, or those with the same characteristics and performance as the

original parts. Use of unauthorized parts can result in fire, electrical shock and/or other danger.

● Upon completion of service or repair work, request the service technician to perform safety checks

to ensure that the unit is in proper operating condition.

Other notices

● Sometimes, the image may have some tiny red, green, blue, white or black sports. This is normal

and does not affect the performance of the LCD TV.

● Due to advanced technology of the LCD TV, giving you fine picture details. Occasionally, a few non-

active pixels may appear on the screen as a fixed point of blue, green, or red. Please note that this

is not affect the performance of your LCD TV.

● If the unit is used in a cold place, a smear may occur in the picture or the picture may become dark.

This does not indicate a failure. These phenomena improve as the temperature rises.

● In some case, residual images may remain after the short-term display of still images is displayed.

These will disappear in a few minutes, and the display will return to normal. However, if used in high

temperatures, it sometimes spends some tens of minutes to return to normal. Please note that this

is not a malfunction.

● LCD panel are made of finely processed glass, so please avoid pushing by fingers or hands and

giving strong impact on the panel. It may cause damage to the LC cells, and/or there is danger of

glass breakage.

● Do not use immediately after moving from a low temperature to a high temperature environment,

as this causes condensation, which may result in fire, electrical shock or other danger.

PACKAGE CONTENTS

Your LCD TV package includes:

1. LCD TV

2. Remote Control

3. Power Cord

4. RCA Cable (3 Pin)

5. Operation Manual

Note:

Your product may also include various other accessories depending on region of purchase.

5

CONTROL BUTTONS AND TERMINALS

FRONT PANEL

2

3

4

4

5

3

2

6

5

6 7

8

Button Name

VOL +/-

MENU

SOURCE

Increase or decrease the volume .

Adjust the values of the selected menu item in the OSD menu.

When you are watching the TV program, press these buttons to select channel in ascending or descending order. Select the upper or lower menu item in the OSD menu.

Enter or exit from the menu.

Select input signal among TV, SCART1, SCART2, Video, S-video,

YPbPr, VGA and DVI.

Switch on the LCD TV when at standby mode or vice versa.

Power Indicator

Illuminates red in standby mode .

Illuminates green when the LCD TV is switched on .

Remote Sensor

Infrared sensor for the remote control.

8 Main Power Switch Switch on/off the LCD TV.

Note:

If there is no signal input from PC/DVI for 1 minute, or no signal input from other video source

(the blue background should be set to On) for over 15 minutes, the LCD TV will switch to standby automatically. The power indicator will light up in red.

6

CONTROL BUTTONS AND TERMINALS

REAR PANEL

1 2 3 4 5 6 7 8 9 10 11 12 13

AC IN DVI

1 AC Input Socket

2 DVI Input Connector

3 AV2-VIDEO Input Terminal

AV1-YPbPr Input Terminals

5 AV2-AUDIO Input Terminals

6 LINE IN (VGA Audio) Terminal

7 AV2-S-VIDEO Input Terminal

8 VGA Input Terminal

9 SCART1 Connector

10 SCART2 Connector

11 HEADPHONE Output Terminal

12 AV1-AUDIO Input Terminals

13 ANTENNA Input Terminal

7

CONTROL BUTTONS AND TERMINALS

REMOTE CONTROLLER

POWER:

Switch on the LCD TV when at standby mode or vice versa.

RETURN:

Return to previously selected program number.

MUTE:

Switch the sound on or off.

POWER MUTE

NICAM/A2

Switch among Stereo, Lang A,

Lang B or Mono.

DISPLAY:

Display the source and channel information.

Numeric Buttons

1.

Press these buttons to select

a TV program directly when

you are watching TV.

2. Press these button to enter

page number in teletext

mode.

MENU SELECT

Enter he OSD menu, or return to previous menu.

t u p q and ENTER

Use to select on screen menu items and change menu values.

SOURCE SELECT

Press to display and to select input source window.

VOL+ / VOL-

Press to increase or decrease volume.

SMODE

You may recall the sound mode by pressing this button. Each time pressed, sound mode is changed in folloing sequence.

Theater " Hall " News

< Memory 8

DISPLAY RETURN NICAM/A2 SYSTEM

1 2 3

4

7

5

8

6

9

MENU

0 -/--/---

EXIT

AV/TV

ENTER

SLEEP

+

VOL

-

TEXT

SMODE PMODE

HOLD

+

CH

-

INDEX PGUP

MIX SIZE SUBPAGE PGDN

RED GREEN YELLOW CYAN

SYSTEM

Select a corresponding sound system.

MENU SELECT

Press to exit the menu.

SLEEP

Press to select sleep time.

PMODE

You may recall the picture mode by pressing this button.

Each time pressed, picture mode is changed in following sequence.

Dynamic " Mild " Standard

< Memory 8

CH+/CH-

Select channel in ascending or descending order.

Teletext Buttons (Optional)

These buttons are used for certain modes with teletext functions only. For further details, refer to the TELETEXT

FUNCTION.

8

BASIC CONNECTION

BATTERY INSTALLATION

Insert the batteries while observing the correct (+) and (-) polarities as illustrated below.

About the batteries

● If the remote control unit fails to work even when it is operated near the LCD TV, please replace

the batteries.

● Use size UM 4 ( AAA ) batteries .

Note

:

● Do not use rechargeable (Ni-Cd) batteries.

● Do not attempt to recharge , short circuit , disassemble , heat or throw the batteries into the fire .

● Do not splash the remote control with water or put it on a wet object to avoid possible.

● Do not drop, step on or cause any impact to the remote control unit. This may damage it, resulting malfunction.

● Do not mix old and new batteries.

● If the remote control unit is not going to be used for a long time , remove the batteries .

● Strong light such as direct sunlight impinging on the remote sensor can cause operational failure.

Place the remote control to avoid direct contact with sunlight.

Caution

Keep batteries out of children’s reach. If batteries are swallowed, contact a physician immediately.

9

BASIC CONNECTION

CONNECTING POWER CORD

1. Connect the power cord to the AC input socket on the rear of the LCD TV, then plug the other

end of the power cord into a correctly wall outlet.

2. Press the POWER (ON/OFF) switch on the rear of your LCD TV to switch on the LCD TV main

power. The power indicator on the front panel turns red and the LCD TV enters into standby

mode automatically.

3. Press the STANDBY button on the remote control or the button on the front panel. The power

indicator turns green. Press the button to return to standby mode.

Note:

Use only the power cord provided.

AC IN DVI

Power cord

CONNECTING THE AERIAL CABLE

Connect a 75 Ω aerial cable to the “ RF IN ” socket on the rear of the LCD TV firmly.

AC IN DVI

Aerial cable

Note:

To view television channel correctly, a signal must be received by the set.

10

BASIC CONNECTION

● Before connecting any external video equipment, please familiarise yourself with the location

and type of each input. If incorrect connections are made, picture or color quality may be

adversely affected. Please ensure that all connectors firmly seated.

● Your external equipment such as DVD player, VCR or home theatre system can be connected

to the rear of the LCD TV so that you can enjoy a complete audio-visual experience.

Note:

Before connecting any external equipment, turn off all main power switch or remove the mains plug from the AC outlet for safety.

CONNECTING TO SCART CONNECTOR

1. Connect the SCART connector on the external video device to the SCART connector 1 or 2 on

the LCD TV using a SCART cable.

SCART1

connector supports full SCART functions (CVBS, RGB input, TV output).

SCART2

connector supports CVBS, Y/C input and Video output.

2. Press the TV/AV button on the remote control to display

AV Switch menu

, then press p / q

buttons to select SCART1 or SCART2 which corresponds with your connection.

SCART cable

DVD or VCR

Input/Output specification:

Connector

SCART1

SCART2

CVBS

ü

ü

Y/C

Input

RGB Audio (L/R) TV

ü ü ü

ü ü

Output

VIDEO Audio (L/R)

ü

ü ü

11

BASIC CONNECTION

CONNECTING TO COMPONENT VIDEO TERMINAL

1. Connect the component output terminals of the external video equipment and the “AV1-YPbPr”

terminals of the rear of the LCD TV using a component video cable.

2. Connect the audio output terminals of the external equipment and the “L” and “R” ports of “AV1-

AUDIO IN” of the rear of the LCD TV using a RCA audio cable.

3. Press the TV/AV button on the remote control to display

AV Switch menu

, then press p / q

buttons to select

YPbPr

which corresponds with your connection, and press the ENTER button

to perform your selection.

Component video cable

RCA audio cable

DVD or VCR

Note:

The Y, Pb, Pr terminals on your external equipment are sometimes labeled Y, B-Y and R-Y or Y, Cb, Cr.

If so, connect the component cable to their matching color terminals.

12

BASIC CONNECTION

CONNECTING TO COMPOSITE VIDEO TERMINALS

1. Connect the composite video output terminal of the external equipment and “AV2-VIDEO” of

the rear of the LCD TV using a RCA video cable.

2. Connect the audio output terminals of the external equipment and the “L” and “R” port of “AV2-

AUDIO IN” of the rear of the LCD TV using a RCA audio cable.

3. Press the TV/AV button on the remote control to display

AV Switch menu

, then press p / q

buttons to select Video which corresponds with your connection, press the ENTER button to

perform your selection.

RCA audio cable

RCA video cable

DVD or VCR

CONNECTING TO S-VIDEO TERMINAL

When connecting an S-VIDEO external equipment to the “AV2-S-VIDEO” terminal of the LCD TV, the picture quality will be further improved.

1. Connect the S-VIDEO output terminal of the external video equipment and the “AV2-S-VIDEO”

terminal of the rear of the LCD TV using a S-Video cable.

2. Connect the audio output terminals of the external equipment and the “L” and “R” port of “AV2-

AUDIO IN” of the rear of the LCD TV using a RCA audio cable.

3 .

Press the TV/AV button on the remote control to display

AV Switch menu

, then press p / q

buttons to select

S-video

which corresponds with your connection, press the ENTER button to

perform your selection.

S-Video cable

RCA audio cable

13

DVD or VCR

BASIC CONNECTION

CONNECTING TO DVI CONNECTOR

Connecting a DVD or set top box via DVI

1 . Connect a DVI D cable or DVI-A cable between the LCD TV and the DVI D or DVI A terminal on the DVD or Set top box .

2 . Connect the audio out terminal of DVD or Set-top-box and the LINE IN terminal of the rear of your LCD TV .

3 . Press the TV/AV button on the remote control to display

AV Switch menu

, then press p / q

buttons to select DVI which corresponds with your connection, press the ENTER button to

perform your selection.

DVI cable

SET-TOP BOX

14

BASIC CONNECTION

CONNECTING TO A PC

1. Connect the VGA output terminal of your computer and the “VGA IN (D-SUB 15PIN)” of the rear

of your LCD TV using a VGA cable.

2. Connect the Line out terminal of your computer and the LINE IN terminal of the rear of your LCD

TV.

3. Press the TV/AV button on the remote control to display

AV Switch menu

, then press p / q

buttons to select

VGA

which corresponds with your connection, press the

ENTER

button to

perform your selection.

Stereo audio cable

PC

VGA cable

CONNECTING TO A HEADPHONE

You can connect a headphone to your LCD TV if you wish to watch a TV program without disturbing the other people in the room.

Insert a headphone into the 3.5mm mini-jack terminal on the LCD TV, the sound is heard through the headphone.

Headphone

Note :

1. Prolonged use of headphones at a high volume may damage your hearing.

2. You will not receive sound from the speakers when you connect headphones to the system.

15

BASIC OPERATION

SWITCHING THE LCD TV ON/OFF

To switch the LCD TV on:

1. Connect the power cord to the LCD TV. Press the main power switch located at the bottom of

the LCD TV. Then the LCD TV switches itself to standby mode and the power indicator on the

front of the LCD TV lights up in red.

2. To switch on the LCD TV from standby:

Press the STANDBY button on the remote control or the button on the front panel of the LCD

TV, the LCD TV switches to on and the power indicator lights up in green.

To switch the LCD TV off:

Press the STANDBY button on the remote control or the button on the front of the unit, the LCD

TV switches to standby mode and the power indicator lights up in red.

To switch the LCD TV off completely, press the POWER ON/OFF switch on the rear of the LCD TV.

ADJUSTING THE VOLUME

Press the t / u button to increase or decrease the volume.

Volume 36

USING MUTE

At any time, you can temporarily cut off the sound using the MUTE button.

1. Press the MUTE button and the sound cuts off.

"Sound mute" will display on the top left corner of the screen.

2. Press the MUTE button again to turn mute off.

USING MENU

1. Press the MENU button on the front panel or on the remote control to display the main menu.

Picture Mode

Contrast

Brightness

Color

Tint

Sharpness

MENU Back EXIT Watch TV

Dynamic

60

50

50

0

0

2. Press the t / u on the front panel or on the remote control to select a sub-menu which you

preform to adjust.

3. In the sub-menu, press p / q on the front panel or on the remote control to select a option which

you want to adjust.

4. After selected a option, press t / u on the front panel or on the remote control to adjust.

5. Press the MENU button to return to provious menu, or press the EXIT button to exit the menu.

Note:

Some options are disabled in gray when they are unavailable in a certain mode. Those items are enabled when corresponding modes are activated.

16

BASIC OPERATION

SELECTING ON SCREEN LANGUAGE

When you start using your LCD TV for the first time, you must select the language which will be used for displaying menus and indications.

1. Press the MENU button to display the menu.

2. Press the t / u button to select SET UP.

3. Press the p / q button to select Language.

4. Then press the t / u button to select your language.

5. When you are satisfied with your choice, press the MENU button to return to normal TV viewing.

CHOOSING A TV CHANNEL

Using the CH ∧ /CH ∨ button on the front panel

, or the p / q button on the remote control

Press the CH ∧ or p button to increase channel number.

Press the CH ∨ or q button to decrease channel number.

Using 0-9 digital buttons and -/--/--- button

You can select the channel number directly by pressing 0 to 9 buttons or -/--/--- buttons.

Example:

To select 1-digit channel (e.g. Channel 5):

● Press the 5 button.

To select 2-digit channel (e.g. Channel 20):

● Press the -/--/--- button repeatedly to display “__” then press 2, follow by 0.

To select 3-digit channel (e.g. Channel 103):

● Press the -/--/--- button repeatedly to display “___” then press 1, follow by 0, then 3.

Note:

After select the digit button, the digit will be memorized.

SELECTING INPUT SOURCE

You can select the input source by press the SOURCE button on the front panel, the source menu will display on the screen, then press the

CH

Ú

/CH

Ù button to select a input source, and press the

ENTER

button to perform the selection.

AV Switch

TV

SCART1

SCART2

Video

S-video

YPbPr

VGA

DVI

17

Picture Mode

Contrast

Brightness

Color

Tint

Sharpness

MENU Back EXIT Watch TV

Dynamic

60

50

50

0

0

PICTURE MENU

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select

PICTURE in the main menu.

3. Press the p / q button to select your option what

you want to adjust in the PICTURE menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the EXIT button to return to the previous

menu or press the MENU button to exit the main

menu.

Picture Mode

Select the type of picture which best corresponds to your viewing requirements by selecting Picture

Mode in PICTURE menu. The following picture effects are available: Dynamic, Standard, Mild and

Memory. Dynamic, Standard and Mild are the factory preset mode. If you want to change the value of Contrast, Brightness, Color, Tint (NTSC only), Sharpness or Color temperature on the picture menu, the Memory option is selected automatically.

& You may select the picture mode directly by pressing the PMODE button on the remote control.

Contrast

Adjust the contrast of the picture.

Brightness

Adjust the brightness of the picture.

Color

Adjust the color saturation.

Note: This option is invalid in PC and DVI mode, and it will be shown in gray.

Tint

Adjust the tone of color when your system is in NTSC.

Sharpness

Adjust sharpness level of the picture.

Color temperature

Select a optimum color temperature mode to suit your eyes for viewing among Normal (balance),

Warm (reddish) Cold (bluish).

DNR (Digital Noise Reduction)

If the broadcast signal received is weak, you can select the DNR option to reduce the video noise level between Auto, Low, Mid, High and off.

Advanced

This option allows you to select the level of Flesh tone, Green tone, Blue tone or Cinema mode.

Note:

If cinema mode is set to Auto, cinema mode will be detected automatically when you are playing a movie with cinema mode.

18

SOUND MENU

Volume

Sound Mode

Bass

Treble

Balance

MENU Back EXIT Watch TV

34

Theater

+35

+45

0

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select SOUND in

the main menu.

3. Press the p / q button to select your

option what you want to adjust in the SOUND

menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Volume

Adjust the sound level.

Sound Mode

You can select the type of sound which best corresponds to your listening requirements by selecting

Sound in SOUND menu. The following sound effects are available: Theater, Hall, News and Memory.

Theater, Hall and News are the factory preset sound mode. If you want to change the value of Bass and Treble on the Sound menu, the Memory option is selected automatically.

& You may select the picture mode directly by pressing the SMODE button on the remote control.

Bass

Increase or decrease the level of the lower-pitched sounds.

Treble

Increase or decrease the level of the higher-pitched sounds.

Balance

Adjust the audio output between left and right speakers.

NICAM/A2 reception

According to the type of sound signal, you can select a appropriate mode among mono, stereo,

Lang A or Lang B.

l When a monaural program is received, you can only choose mono.

l When a stereo program is received, you can switch between stereo and mono.

l When a bilingual or dual program is received, you can switch among Lang A, Lang B and mono.

Lang A

sends the primary broadcast language to loudspeakers.

Lang B

sends the secondary broadcast language to the loudspeakers.

Note:

If the stereo signal is weak, it will be switched to mono automatically.

19

SET UP MENU

TV MODE

Language

Auto tuning

Manual tuning

Program Label

Program Edit

MENU Back EXIT Watch TV

English

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select SET UP in

the main menu.

3. Press the p / q button to select your

option what you want to adjust in the SET UP

menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Language

This option allows you to select the language of OSD (on screen display) by pressing the t / u .

Auto tuning

This option allows you to Tuning the stations that can be received automatically. It’s recommended that you use Auto tuning during installation of this unit.

Tips: Before perform Auto tuning, you must select a country where you are by selecting Country option in the FUNCTION menu.

1.Press the p / q button to select Auto tuning in SET UP menu.

2. Press the t / u button to perform your selection, sound system will be displayed on the screen.

Auto tuning

Choose Sound Mode

!

B/G

Press ENTER key to start.

MENU Back EXIT Watch TV

3. In Auto tuning menu, press the t / u button to select a corresponding TV system.

4. Press the ENTER button to start auto tuning. A brand of tuning progress will displayed on the bottom

side of the screen.

Auto tuning

Searching

Pos: 4

EXIT

Stop

135.25MHz

5. During searching, you can press the EXIT button to stop searching at any moment, and return

to the previous menu.

20

SET UP MENU

Manual tuning

This option allows you manually tune for your broadcast stations or fine tune the channels received.

Tips: Before perform Manual tuning, you must select a country where you are by selecting Country option in the FUNCTION menu.

1. Press the p/q button to select Manual tuning in SET UP menu.

2. Press the t/u button to perform your selection, and the menu of Manual tuning will be displayed

on the screen.

Program

Sound System

Color system

Skip

AFT

Manual search

Manual tuning

34

B/G

Auto

On

Auto

865.25MHz

MENU Back EXIT Watch TV ENTER SAVE

Program

The current program number. Press the t / u button to select the upper or lower program.

Sound System

The sound system. Press the t / u button to select a corresponding sound system.

Color system

The color system. Press the t / u button to select a corresponding color system.

Skip

Skip option allows you to skip the current channel. When set On, the program number will be skipped when you select the skipped channel with the CH+/CH- button. But you can select the skipped channel by pressing the numeric buttons directly.

AFT (Auto fine tune)

Due to weak signals or a wrong antenna configuration, some of the channels may not be turned to the best reception condition. AFT function allows you to fine tune the selected channel.

Manual search

Manual search option allows you to preset channels one by one, in the program order of your choice.

Program Label

This option allows you to name for a selected channel, you can also rename the program which you have named.

1. Select a channel which you would like to operate for it.

2. Press the p / q button to select Program Label in SET UP menu.

3. Press the t / u button to perform your selection, and the menu of bar of program label will

display on the bottom side of the screen.

Program Label

21

SET UP MENU

4. Press the numeric buttons to input the numbers directly or press the p / q button to select the

letters.

5. Press the t / u button move the cursor.

6. After completed, press the ENTER button to return the previous menu or press the EXIT button

to exit the main menu.

Program Edit

This function allows you to reorganize the order of the TV programs according to your preferences.

1. Press the p / q button to select Program edit in SET UP menu.

2. Press the t / u button to enter into the sub menu, and a channel list will be appeared on the

screen.

3. Press the p / q to select a channel in the list which you would like to sort.

4. Press the u button to perform your selection.

5. Press the p / q button to select a channel in the list where you would like to place at.

6. Press the t to perform your selection.

7. After completed, press the MENU button to return to the previous menu or press the EXIT button

to exit the main menu.

SCART, VIDEO and S-VIDEO MODE

Language

Color system

SET UP

English

Auto

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select SET UP in

the main menu.

3. Press the p / q button to select your option what

you want to adjust in the SET UP menu.

4. Press the t / u button to adjust.

MENU Back EXIT Watch TV

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Language

This option allow you to select the language of OSD (on screen display) by pressing the t / u .

Color system

Select a corresponding color system.

22

SET UP MENU

YPBPR MODE

Language

YPbPr position

MENU Back

SET UP

EXIT Watch TV

English

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select SET UP in

the main menu.

3. Press the p / q button to select your option what

you want to adjust in the SET UP menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Language

This option allows you to select the language of OSD (on screen display) by pressing the t / u .

YPbPr position

This option allows you to adjust the position in YPbPr mode. In SET UP menu, press the p / q button to select YPbPr position, then press the u button to enter into the sub menu, YPbPr position menu will appear on the screen.

H Position

V Position

Reset

YPbPr Position

+2

+2

MENU Back EXIT Watch TV

H (Horizontal) position

Adjust the screen horizontal position.

V (Vertical) position

Adjust screen vertical position.

Reset

Replace H position and V position with the factory default values.

23

SET UP MENU

VGA MODE

Language

VGA position

SET UP

MENU Back EXIT Watch TV

English

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select SET UP in

the main menu.

3. Press the p / q button to select your option what

you want to adjust in the SET UP menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Language

This option allows you to select the language of OSD (on screen display) by pressing the t / u .

VGA position

This option allows you to adjust the position in VGA mode. In SET UP menu, press the p / q button to select VGA position, then press the u button to enter into the sub menu, VGA position menu will appear on the screen.

VGA Position

Auto Sync

Phase

Clock

V Position

H Position

Reset

MENU Back

3

3

0

0

EXIT Watch TV

Auto Sync

Adjust screen settings automatically for optimized picture position.

Phase

Remove any horizontal interference.

Clock remove any vertical interference.

V (Vertical) Position

Adjust screen horizontal position.

H (Horizontal) Position

Adjust screen vertical position.

Reset

Replace Phase, Clock, V Position and H Position with the factory default values.

24

SET UP MENU

DVI MODE

Language

DVI position

SET UP

MENU Back EXIT Watch TV

English

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select SET UP in

the main menu.

3. Press the p / q button to select your option what

you want to adjust in the SET UP menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Language

This option allows you to select the language of OSD (on screen display) by pressing the t / u .

DVI position

This option allows you to adjust the position in DVI mode. In SET UP menu, press the p / q button to select PC position, then press the u button to enter into the sub menu, PC position menu will appear on the screen.

H Position

V Position

Reset

DVI Position

+2

+2

MENU Back EXIT Watch TV

H (Horizontal) position

Adjust the screen horizontal position.

V (Vertical) position

Adjust screen vertical position.

Reset

Replace H position and V position with the factory default values.

25

Sleep Timer

Off timer

On timer

On timer position

TIMER

MENU Back EXIT Watch TV

Off

00:00

00:00

03

TIMER MENU

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select TIMER in

the main menu.

3. Press the p / q button to select your option what

you want to adjust in the TIMER menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Sleep timer

Select the sleep time to automatically to standby. Time is set in increments of 10 minutes, from off to 120 minutes.

& You may select the sleep time directly by pressing the SLEEP button repeatedly on the remote control.

Off timer

This LCD TV can be set to turn itself off after a certain time.

On timer

This LCD TV can be set to turn itself on after a certain time.

On timer position

This option allows you to set a channel number which you desire to play when the TV is tuned on.

Note:

This option is activated when On time option has been set.

26

Aspect

Blue screen

KeyLock

Country

FUNCTION

MENU Back EXIT Watch TV

FUNCTION MENU

16:9

On

Off

Croatia

1. Press the MENU button to display the OSD main

menu.

2. Press the t / u button to select

FUNCTION in

the main menu.

3. Press the p / q button to select your option what

you want to adjust in the

FUNCTION

menu.

4. Press the t / u button to adjust.

5. When you are satisfied with your adjustment,

press the MENU button to return to the previous

menu or press the EXIT button to exit the main

menu.

Aspect

This option allows you to select the screen display mode which best corresponds to your viewing requirement, 5 kinds of aspect mode are available: Original, 16:9, 16:9 Zoom, 16:9SUB and 14:9.

Note:

The available aspect mode may be different in difference input signal.

Blue screen

This option allows you to select the blue background on or off. If on, the screen background will turn blue at very weak or no signal condition.

KeyLock

This option allows you to lock the function buttons on the front panel , so that a childmay not accidentally change your viewing preferences.

Country

This option allows you to select a country where you are.If your local county doesn’t list on the menu,you can select other.

Note:

It is strongly recommended that select a corresponding country where you are before start to search channel.

27

TELETEXT FUNCTION (OPTION)

Teletext is an optional function, therefore only certain models can receive the teletext broadcast.

Teletext is a free broadcast service by most TV stations which gives up-to-the-minute information on news, weather, television program, share prices and many other topics.

Display Teletext

1. Select a TV station with teletext signal.

2. Press the TEXT button to enter Teletext signal.

3. Press the TEXT button again to return to the normal TV mode.

Page Selection

1. Enter the page number (three digit) using the number buttons.

If you press a wrong number during input, you must complete the three digit number and then

re-enter the correct page number.

2. The PGUP/PGDN button can be used to select the preceding or following page.

HOLD

You can press the HOLD button to hold a page, and press this button again to release the page.

INDEX

Press the INDEX button to enter the main index page directly.

You may enter the main index page number directly using the number buttons.

Enlarging Text

When a page is displayed, you can double the size of the text to make it easier to read.

1. Press the SIZE button to enlarge the top half of the page.

2. Press the SIZE button again to enlarge the bottom half of the page.

3. Press this button once more to return to the normal display.

Reveal mode

You can display concealed teletext information (e.g. Answer to puzzles or riddles etc.) by pressing this button. Press this button again to remove the information from the display.

MIX Mode

This function enables you to superimpose the Teletext page over the TV program, or allocate the

Teletext page and TV program side by side.

1. When a page is displayed, press the MIX button. The TV page will appear with the text page.

2. Press the MIX button again, the text page and TV program will allocate side by side.

3. The third time, press the MIX button to return to the normal text mode.

SUBPAGE

Some teletext page may contain several sub-pages which are automatically paged in a certain cycle by the TV station.

1. You can enter to a certain sub page by pressing the SUBPAGE button directly and select the

page number with the number buttons. Enter the subpage number (e.g. 0003) for the third sub-

page.

2. Press the SUBPAGE button again to exit the sub page mode.

3. Press the TEXT button to return to the normal TV mode.

COLOR buttons (RED, GREEN, YELLOW, CYAN)

Press these buttons to access directly to the corresponding color pages displayed at the lower part of the teletext screen.

28

SUPPORTED OPERATING MODES

COMPONENT VIDEO (YPbPr) INPUT

Mode Resolution

576i

480i

576p

480p

1080i/50

1080i/60

720p/60

SXGA

DVI INPUT

Mode

DOS

VGA

VGA

VGA

SVGA

SVGA

SVGA

XGA

XGA

XGA

SXGA

RGB INPUT

Mode

DOS

VGA

VGA

VGA

SVGA

SVGA

SVGA

XGA

XGA

XGA

WXGA

576

480

576

480

1080

1080

720

Resolution

720X400

640X480

640X480

640X480

800X600

800X600

800X600

1024X768

1024X768

1024X768

1280X768

1280X1024

Resolution

720X400

640X480

640X480

640X480

800X600

800X600

800X600

1024X768

1024X768

1024X768

1280X1024

Horizontal Frequency (K Hz)

15.63

15.73

31.26

31.47

28.13

33.75

44.96

Horizontal Frequency (K Hz)

31.5

31.5

37.9

37.5

37.9

48.1

46.9

48.4

56.5

60.0

47.8

64.0

Horizontal Frequency (K Hz)

31.5

31.5

37.9

37.5

37.9

48.1

46.9

48.4

56.5

47.8

64.0

Vertical Frequency (Hz)

50.00

59.94/60.00

50.00

59.94/60.00

50.00

59.94/60.00

59.94/60.00

Vertical Frequency (Hz)

70.0

60.0

72.0

75.0

60.0

72.0

75.0

60.0

70.0

75.0

60.0

60.0

Vertical Frequency (Hz)

70.0

60.0

72.0

75.0

60.0

72.0

75.0

60.0

70.0

75.0

60.0

● Modes, which are not listed in the above table, may not be supported. For an optimal picture is

recommended to choose a mode listed in the table.

● The incoming display modes compatible with WINDOWS as shown in the table above.

● Sometimes, the image may be disrupted due to the frequency standard from the VGA card.

However, this is not an error. You may improve this situation by activating the automatic

adjustment or by manually changing the phase and the clock settings in the menu.

● T o extend the service life of the product, we recommend that you use your computer’s power

management function.

29

TROUBLESHOOTING

Before contrast the service technician, perform the following simple checks. If any problem still persists, unplug the LCD TV and calling for serving.

Problem

No sound or picture

Normal picture but no sound

Sound is too low

Possible Solution

● Check that the main plug has been connected to a wall let.

● Check that you have pressed the button on the front of

the TV.

● Check the picture contrast and brightness settings.

● Check the volume .

● Check the volume.

● Check whether then MUTE button has been pressed on the

remote control.

● Check the volume .

● If the volume is still too low after setting the volume level to its

maximum, check the volume control on computer sound card

or software program.

No picture or black and white picture

● Adjust the colour settings .

● Check that the broadcast system selected is correct.

“Unknown” message

Sound and picture interference

Blurred or snowy picture, distorted sound

● Make sure that the power cord is firmly connected to the

PC or the video sources.

● Make sure that the PC or video sources are switched on.

● Try to identify the electrical appliance that is affecting the

set and move it further away.

● Check the direction, location and connections of your aerial.

Remote control does not work

● The battery in the remote control may be exhausted.

● The battery may be improperly installed.

● Check that there is no obstruction between the remote control

and the remote (infrared) sensor.

● Ensure that there is no strong light shining on the remote

control’s infrared sensor.

The LCD TV does not turn on ● Be sure the power cord is plugged on.

The image is too light or too dark

On PC mode, horizontal bars appear to flicker, jitter or shimmer on the image

● Adjust the brightness and Contrast.

● Adjust the Phase.

On PC mode, vertical bars appear to flicker, jitter or shimmer on the image

● Adjust the Clock.

On PC mode, image is not stable and may appear to vibrate

● Check that the display resolution and frequency from you

PC or video board is a valid mode for your LCD TV.

Control Panel g Display g Settings.

● If the setting is not correct, use your computer utility program

to change the display settings.

Your monitor supports multiscan display function within the

follow-ing frequency domain:

Horizontal frequency:30KHz~75KHz

Vertical frequency: 56~75Hz

Maximum refresh rate:1280X1024 @ 60Hz

On PC mode, image is not centred on the screen.

● Adjust the horizontal and vertical position.

30

SPECIFICATIONS

LCD Panel

Size

Display size

Pixel Pitch

View Angle

Frequency

Horizontal

Vertical

Display color

Display Resolution

Maximum Mode

Optimum Mode

Input Source

Sync .

Video Signal

RGB Signal

TV

Color System

Sound System

Video

Color System

Video Format

Power Supply

Input

Power Consumption

Working

Standby

Environmental Considerations

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

Audio Characteristics

Audio Input

Audio Input

Frequency

Response

Dimension ( WXDXH ) mm

Without Stand

With Stand

Weight ( Kg )

Net Weight

Gross Weight

27

1280 X 1024 @ 60Hz

1280 X 768 @ 60Hz

H/V separate, TTL, P. or N.

1Vp-p @ 75 ohm

0.7 Vp-p @ 75 ohm

10 ℃ ~ 40 ℃

10% ~ 80%

(50°F ~ 104°F)

-30 ℃ ~ 45 ℃

5% ~ 95% i

" Diagonal

566 .

40(H) X 339 .

84(V) mm

0.4425(H) X 0.4425 (V) mm

176 °/176°(H/V)

30~75kHz

56~75Hz

16.7M colors

PAL/SECAM

BG, DK, I, L

PAL/SECAM/NTSC

CVBS, S-VHS, RGB

AC 100~240V, 50/60Hz

140W

< 3W

RCA Jack (L, R), 0.5Vrms (-9dB)

3.5 Stereo Jack, 0.5Vrms (-9dB)

RF: 100Hz~12KHz (at ± 3dB)

A/V: 100Hz~13KHz (at ± 3dB)

681.2X93.4X474.0

681.2X245.5X527.9

11.0

14.0

Note:

● Design and specifications are subject to change without notice.

● Weight and dimensions shown are approximate values only.

31

32 " Diagonal

697.68(H) X 392.26(V) mm

0.51075(H) X 0.51075 (V) mm

176 °/176°(H/V)

30~75kHz

56~75Hz

16.7M colors

1280 X 1024 @ 60Hz

1280 X 768 @ 60Hz

H/V separate, TTL, P. or N.

1Vp-p @ 75 ohm

0.7 Vp-p @ 75 ohm

PAL/SECAM

BG, DK, I, L

PAL/SECAM/NTSC

CVBS, S-VHS, RGB

AC 100~240V, 50/60Hz

165W

< 3W

10 ℃ ~ 40 ℃ (50°F ~ 104°F)

10% ~ 80%

-30 ℃ ~ 45 ℃

5% ~ 95%

RCA Jack (L, R), 0.5Vrms (-9dB) i 3.5 Stereo Jack, 0.5Vrms (-9dB)

RF: 100Hz~12KHz (at ± 3dB)

A/V: 100Hz~13KHz (at ± 3dB)

812.9X106.0X560.9

812.9X245.5X619.0

15.2

18.2

advertisement

Related manuals

Download PDF

advertisement