Ganz ZN-NH21VE Installation Manual
Ganz ZN-NH21VE is a high-quality megapixel IP camera with a built-in VCA (Video Content Analysis) system, making it ideal for use in surveillance applications. It features a 1/3.2" CMOS sensor that captures images at a resolution of up to 1600 x 1200 pixels. With support for dual streaming in H.264, MJPEG, and MPEG formats, the camera can deliver smooth video footage for both monitoring and recording purposes. Additionally, it has built-in audio support for two-way communication.
Advertisement
Advertisement
ZN ‐ NH21VE Installation Manual
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
!
!
This symbol is intended to alert the user to the presence of un ‐ insulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
2010/2 ‐ 1 01B.00
2
ZN ‐ NH21VE Installation Manual
Table of Contents
1.
FEATURES ............................................................................................................... 5
2.
PACKAGE CONTENTS .............................................................................................. 6
3.
PART NAMES .......................................................................................................... 7
3.1.
Rear View ........................................................................................................................... 7
3.2.
Bottom View....................................................................................................................... 7
!
Caution
.............................................................................................................................. 8
4.
INSTALLATION ........................................................................................................ 9
4.1.
Installing a C/CS Mounting lens.......................................................................................... 9
4.2.
Setting the Image Attribute................................................................................................ 9
4.3.
Installing a Wireless USB Adapter (Optional)................................................................... 10
5.
CONNECTIONS ...................................................................................................... 11
!
Caution
............................................................................................................................ 11
5.1.Connectors ........................................................................................................................ 12
6.
CONFIGURATION .................................................................................................. 15
6.1.Set
up network environment ............................................................................................ 15
6.2.
View video on web page .................................................................................................. 15
6.2.1.
View video using ZNS ‐ GIT IPAdmin Tool ................................................................... 15
6.2.2.
View video using IP address ...................................................................................... 18
6.3.
Reset................................................................................................................................. 18
6.4.
Factory Default................................................................................................................. 18
APPENDIX (A): SPECIFICATIONS ................................................................................ 19
Summary ................................................................................................................................. 19
Resolutions per Codec Frame rate .......................................................................................... 20
Electrical Characteristics ......................................................................................................... 20
Environment Condition ........................................................................................................... 20
Mechanical Condition ............................................................................................................. 20
VCA (Video Content Analysis) ................................................................................................. 21
2010/2 ‐ 1 01B.00
3
ZN ‐ NH21VE Installation Manual
APPENDIX (B): POWER OVER ETHERNET................................................................... 22
PoE compatibility .................................................................................................................... 22
Power classification................................................................................................................. 22
APPENDIX (C): DIMENSIONS ..................................................................................... 23
APPENDIX (E): TROUBLE SHOOTING ......................................................................... 24
Checking your Firmware ......................................................................................................... 24
Upgrading the Firmware ......................................................................................................... 24
Support.................................................................................................................................... 24
2010/2 ‐ 1 01B.00
4
ZN ‐ NH21VE Installation Manual
1. FEATURES
Camera
Box type IP Megapixel Camera
Aptina (Micron) 1/3.2" (4:3) CMOS 2M pixels
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
De ‐ interlacing on DSP
Burnt ‐ in text supported
Unicast/Multicast supported
Video/Audio
Megapixel Compression: H.264, MJPEG, Up to 1600 x 1200
Video compression: H.264/MPEG/MJPEG (Dual Stream@D1)
Audio compression: G.711(µLaw, aLaw)/PCM
Video Motion Detection supported
2 ‐ way mono audio supported
Network
RTSP/ HTTP protocol supported
10/100 Base ‐ T Ethernet
Additional Features
RS ‐ 485 supported
USB 2.0
supported (External storage, Wireless LAN)
Micro SD card slot supported
PoE supported
Built ‐ in Video Content Analysis
OSD supported
SDK (Software Development Kit) provided
VCA (Video Content Analysis)
VCA Presence (Included as basic)
VCA Surveillance (Optional)
2010/2 ‐ 1 01B.00
5
ZN ‐ NH21VE Installation Manual
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care.
The packaging contains:
ZN ‐ NH21VE DC power adaptor
Mount ring
Rubber cap (for protecting CCD)
Adaptor for mounting the camera
9 Pin
Hex
terminal wrench
Screws
block driver
Quick Installation Guide
DC Jack Adaptor Cable
i
Note
The above contents are subject to change without prior notice.
2010/2 ‐ 1 01B.00
6
3. PART NAMES
3.1. Rear View
Feh Feh
ZN ‐ NH21VE Installation Manual
Feh
RS-485 DO DI
RESET
AUDIO
+
C 1 C 1 Out In
Micro SD
ETHERNET
Feh
①
Feh
Feh
3.2. Bottom View
2010/2 ‐ 1 01B.00
Feh
7
ZN ‐ NH21VE Installation Manual
Reset
Reset switch is used for restarting or resetting camera as Factory Default (FD).
Refer to the
section “ 6.3.
Reset” for more specific information.
USB connector
Insert a USB storage device or Wi ‐ Fi devices.
(Only Ralink RT73 chipsets based wireless devices are available.)
9 pin terminal block for D/I, D/O, audio, and serial communication
Refer to the section “ 5.1.Connectors” for more specific information.
Power Adaptor Connector (DC 12V)
ZN ‐ NH21VE needs a DC12V for power supply.
Refer to the section “ Power Adaptor Connector
(DC 12V)” for more specific information.
+ ‐
!
Caution
Make sure the polarity is correct.
Incorrect connection may cause malfunction or damage to the IP device.
Micro SD Card slot
It is a memory card slot for external storage.
LAN Connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base ‐ T Ethernet.
Status LED Network LED
Adaptor for mounting the camera
Mounting points adaptor is provided on the bottom (or the top) of the camera for mounting the camera on a bracket or tripod.
2010/2 ‐ 1 01B.00
8
4. INSTALLATION
ZN ‐ NH21VE Installation Manual
CCW
Set Screw
*Lens is optional.
i
Note
We recommend that use a megapixel lens with manual iris to support the full resolution of megapixel camera.
4.1. Installing a C/CS Mounting lens
1.
Remove the protective rubber cap from the front of the camera.
2.
Install the mount ring for lens and adjust the mount ring to fit C or CS lens.
3.
Tighten the setscrews using the hex wrench in the package.
4.2. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video ‐ in > Image
Signal Processing .
The following features can be adjusted:
Brightness
Contrast
Saturation
Sharpness
Mirroring
Lighting Attribute
For more detailed information, refer to the ‘Webpage User’s Manual’ in the SDK.
2010/2 ‐ 1 01B.00
9
ZN ‐ NH21VE Installation Manual
4.3. Installing a Wireless USB Adapter (Optional) i
A wireless USB adapter is sold separately as an optional kit.
Please contact your supplier or system integrator to purchase a wireless USB adapter.
Note
The kit includes:
USB cable
3M Double ‐ coated tape
Wireless USB adapter
Perform the following steps to install a wireless USB adapter:
1.
Connect one end of the USB cable to the camera.
2.
Connect the other end of the USB cable to a wireless USB adapter.
3.
Use the enclosed double ‐ coated tape to attach the wireless USB adapter to the desired area.
You can attach the adapter on the body (side, top, or bottom) of the camera, ceiling, or wall.
2010/2 ‐ 1 01B.00
10
5. CONNECTIONS
ZN ‐ NH21VE Installation Manual
DC Jack Adaptor
RS-485 DO DI
RESET
AUDIO
+
C 1 C 1 Out In
Micro SD
Power Adaptor
LAN Cable
ETHERNET
!
Caution
When connecting the DC power supply, make sure the polarity is correct.
Incorrect connection may cause malfunction or damage to the camera.
2010/2 ‐ 1 01B.00
11
ZN ‐ NH21VE Installation Manual
5.1.Connectors
9 pin terminal block
RESE
RS-485 DO DI
T
O
- +
C 1 C 1 O ut
In
Micro SD
ETHERN
ET
RS ‐ 485
The RS ‐ 485 serial port consists of TRX+(RX+) and TRX ‐ (RX ‐ ) as following the following image.
TRX+(RX+)
TRX-(RX-)
<RS-485 Application>
TX+
TX-
485 Devices
+
-
RS ‐ 485 Connection
Sensor (DI) connection
ZN ‐ NH21VE provides 1 channel D/I.
It can be connected to either a voltage type sensor or a
relay type sensor as the following figures.
It can be selected by software.
Input voltage range: 0 VDC minimum to 24 VDC maximum
Input voltage threshold: 1 V
!
Caution
Do not exceed the maximum input voltage or relay rate.
2010/2 ‐ 1 01B.00
12
ZN ‐ NH21VE Installation Manual
Internal +5V
DI
Output of
Sensor
+ ‐
Internal
DI 1
Output of
Sensor
+ ‐
COM ‐ + COM
Relay Type
Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VAC 500mA or 12VDC 1A
!
Caution
Do not exceed the maximum relay rating.
Internal
DO
Device
Voltage Type
COM
Relay Type
Audio connection
ZN ‐ NH21VE has a mono audio input and a mono audio output.
As the output power for the audio is low, amplifier speaker is needed.
(Do not use a headphone or earphone directly to the camera.)
Aout
Speaker
Ain Mic
2010/2 ‐ 1 01B.00
13
Power Adaptor Connector (DC 12V)
Power adaptor connector connects to DC Jack adapter cable.
ZN ‐ NH21VE Installation Manual
+
RED
+ ‐
‐
!
Caution
Make sure the polarity is correct.
Incorrect connection may cause malfunction or damage to the IP device
!
Power Adaptor Connector (DC 12V)
Caution
2010/2 ‐ 1 01B.00
14
ZN ‐ NH21VE Installation Manual
6. CONFIGURATION
6.1.Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX.
You can find the available IP address from the MAC address of your device.
Please make sure the device and your PC are on the same network segment before running the installation.
If the network segment between your PC and the device is different, change your PC’s settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.2. View video on web page
View the live video on a web page using your IP device and its IP address.
You can use the ZNS ‐
GIT IPAdmin Tool or enter the IP address on the web page.
6.2.1. View video using ZNS-GIT IPAdmin Tool
ZNS ‐ GIT IPAdmin Tool automatically searches all activated GANZ Network Camera and Encoder series and shows the product name, IP address, MAC address and etc.
ZNS ‐ GIT IPAdmin Tool is provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
2010/2 ‐ 1 01B.00
15
ZN ‐ NH21VE Installation Manual
To use the ZNS ‐ GIT IPAdmin Tool and view the live video on a web page:
1.
Start ZNS ‐ GIT IPAdmin Tool.
Names and info of currently activated devices appear as a list.
2.
Right ‐ click on the desired device and select Web view .
3.
Select Continue to this website on the Security Certificate Alert page.
(The explanation and captured images at this manual are mainly on the basis of Internet
Explorer 7.0)
4.
Click pop ‐ up blocked and install the ActiveX control as below.
You need to install the
ActiveX for displaying the images.
2010/2 ‐ 1 01B.00
16
ZN ‐ NH21VE Installation Manual
5.
Wait for a few seconds while the web page loads.
The live video is displayed as below.
6.
If the live video is not displayed and “Can not Create XMLDOMDocument Install
MSXML4.0” message is shown as below, please download and Install from the link below.
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B ‐ B4F2 ‐ 46DA ‐
B4B6 ‐ C5D7485F2B42&displaylang=en
(VCA Library requires MS XML 4.0
library which is an xml parser made by Microsoft.)
2010/2 ‐ 1 01B.00
17
ZN ‐ NH21VE Installation Manual
6.2.2. View video using IP address
View the live video on a web page using your IP device and its IP address.
To have the correct
IP address ready and use it on a web page:
1.
Convert a MAC address to an IP address or check the IP address on the ZNS ‐ GIT IPAdmin Tool.
(The MAC address is attached on the side or bottom of the device.)
MAC address = 00 ‐ 1C ‐ B8 ‐ C0 ‐ 14 ‐ B1 → IP address = 192.168.20.177
the Hexadecimal number to Decimal number.
2.
Open a web browser and enter the IP address of the device.
3.
Click Continue to this website on the Security Certificate Alert page.
4.
Click pop ‐ up blocked and install the ActiveX control.
You need to install the ActiveX for displaying the images.
5.
Wait for a few seconds while the web page loads.
The live video is displayed.
6.3. Reset
1.
While the device is in use, press and hold the Reset .
2.
Release the Reset button after 3 seconds.
3.
Wait for the system to reboot.
6.4. Factory Default
1.
Disconnect the power supply from the device.
2.
Connect the power to the device with the Reset button pressed and held.
3.
Release the Reset button after 5 seconds.
4.
Wait for the system to reboot.
The factory default settings can be inferred as follows:
IP address: 192.168.xx.yy
Network mask:
Gateway:
255.255.0.0
192.168.0.1
User ID:
Password:
root pass
2010/2 ‐ 1 01B.00
18
ZN ‐ NH21VE Installation Manual
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
Model
Image Sensor
Effective Pixels
Scanning system
Dynamic Range
SNR
Minimum Illumination
Lens (Optional)
Day & Night
Video
Megapixel Compression
Compression Format
Number of Streams
Resolution
ZN ‐ NH21VE
Aptina (Micron) 1/3.2" (4:3) CMOS 2M
1600 x 1200 (UXGA, 2M)
Progressive Scan
71dB
Max 42.3dB
0.5
Lux(50IRE), 0.1
Lux(DSS x5 ON)
3~8 mm, F1.0
Manual Iris Lens, CS Mount
S/W
Compression FPS
(In case of VCA or Burnt In
Annotation on, fps could be decreased)
H.264
MJPEG
MPEG4
Motion Detection
Burnt ‐ in Text
Video Output
Audio
Input / Output
Compression Format
Function
Digital Input
Digital Ouput
RS ‐ 485
RS ‐ 232
Network
Protocol
USB
SD
2.0
Slot
H.264
and MJPEG
H.264, MPEG ‐ 4, and MJPEG
Dual Stream, Configurable
See Resolutions table
below
5 fps@UXGA (1600 x 1200)
8 fps@SXGA (1280 x 1024)
15
12 fps@XGA
15
fps@HD720
x fps@UXGA
768),
(1600
15fps@D1&720x480)
Support
Support
Not
1/1
(1024
(DSP)
(DSP)
Available channel
G.711
(1280
x
x
D1
720)
(720
1200)
x 480)
1 channel (Dry and Wet Contact Selectable)
1 channel (Dry Contact)
Support
Not Available
10/100 Base ‐ T
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, SNTP, mDNS, UPnP, SMTP, SOCK, IGMP,
DHCP, FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH
Support (Mini ‐ B plug)
Supported (Micro SD type)
※ Micro SD Card is not included
2010/2 ‐ 1 01B.00
19
ZN ‐ NH21VE Installation Manual
Resolutions per Codec Frame rate
Codec
Resolution
UXGA (1600x1200)
SXGA (1280x1024)
HD720 (1280x720)
XGA (1024x768)
D1 (720x)
4CIF (704x)
VGA (640x)
CIF (352x)
QVGA (320x)
QCIF (176x)
MPEG4
Not available
Not available
Not available
Not available
15 fps
H.264
5 fps
8 fps
12 fps
15 fps
MJPEG
15 fps
Electrical Characteristics
Audio Input
Audio Output
Sensor(D/I)
Alarm(D/O)
Power Source(Approx)
Power over Ethernet
Power Consumption
(Approx)
Linein, 1.43Vp
‐ p(Min 1.35Vp
‐ p, max 1.49
Vp ‐ p), 39 K Ω
Lineout, 46mW Power, 16 Ω
TTL level 4.5V
threshold, Max 50mA
Max 500mA@24VAC or 1A@12VDC
12V DC (Screw Terminal)
IEEE802.3af(class 0)
300 mA @ +12V
Environment Condition
Operating Temperature
Operating Humidity
0 ˚ C ~ 50 ˚ C (32 ˚ F ~ 122 ˚ F)
Up to 85% RH (Non ‐ condensing)
Mechanical Condition
Material
Color
Dimension
Weight (Approx)
Aluminum Die Casting ‐ 2
White Pearl
55(W) x 55(H) x 91.4(D) mm
260 g
2010/2 ‐ 1 01B.00
20
ZN ‐ NH21VE Installation Manual
VCA (Video Content Analysis)
VCA Presence (Included as Standard)
High Performance Advanced Tracking Algorithm, Low False Alarm Rate
Easy to Use
Detection Zones
On ‐ screen Display
Burnt ‐ in Annotation
VCA Surveillance (Option)
Intuitive
Multi
Real ‐
‐
Web segment time
Stream
Browser
Polygons
Display of
Interface
and
Tracking
Lines
Data
and Events
Detection
3D
Behavior
Behavior
Camera Tampering, Direction, Stopping, Loitering, Entering,
Exiting, Appear, and Disappear Filters
Perspective Corrected Size and Speed Filters
Statistics Counting Functions
Binary XML Format
and Other Statistics
Meta Data
Image Stabilization (Option)
Electronic Stabilization Removes Camera Sway
2010/2 ‐ 1 01B.00
21
ZN ‐ NH21VE Installation Manual
APPENDIX (B): POWER OVER ETHERNET
The Power over Ethernet(PoE) is designed to extract power from a conventional twisted pair
Category 5 Ethernet cable, conforming to the IEEE 802.3af
Power ‐ over ‐ Ethernet (PoE) standard.
IEEE 802.3af
allows for two power options for Category 5 cables.
The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by the Power Sourcing Equipment (PSE) before applying up to
15W power to the port.
The high efficiency DC/DC converter operates over a wide input voltage range and provides a regulated low ripple and low noise output.
The DC/DC converter also has built ‐ in overload and short ‐ circuit output protection.
PoE compatibility
With non Power Sourcing Equipment (PSE)
When it is connected with non PSE, the power adaptor should be connected.
With power adaptor
Connecting both PSE and power adaptor does not do any harm to the products.
Disconnecting power adaptor while it is operating does not stop operation.
The product continues to work without rebooting.
Power classification
The PoE Power Class supported by the IP device is Class 0.
Class Usage Minimum Power Levels
Output at the PSE
0 Default 15.4W
Maximum Power Levels at the
Powered Device
0.44
to 12.95W
2010/2 ‐ 1 01B.00
22
APPENDIX (C): DIMENSIONS
ZN ‐ NH21VE Installation Manual
55
Top view
RESET
RS-485 DO DI AUDIO
+
C 1 C 1 Out In
Micro SD
ETHERNET
Rear view
Front view
2010/2 ‐ 1 01B.00
Right side view
UNIT: mm
23
ZN ‐ NH21VE Installation Manual
APPENDIX (E): TROUBLE SHOOTING
Checking your Firmware
Firmware is software that determines the functionality of the device.
One of your first actions when troubleshooting a problem should be to check the currently installed version.
The latest version may contain a correction that fixes your particular problem.
The current firmware version in your device can be seen under Setup > About > Version.
Upgrading the Firmware
New firmware can be downloaded at the FTP site.
When you download firmware from the FTP, your product will receive the latest available functionality.
Always read the upgrade instructions and release notes available with each new release, before updating the firmware.
If you want to know more, please contact our sales person.
Support
If you cannot resolve an issue, for additional assistance, please contact your supplier or system integrator
If you contact our support, please help us by providing a server report, log file and a brief
description of the problem.
1.
In the address bar of your browser, after the unit IP address enter following CGI command.
<IP ADDRESS> /nvc ‐ cgi/admin/param.cgi?action=list
<IP ADDRESS> /nvc ‐ cgi/admin/vca.cgi?action=list
The server report contains important information about the device, as well as a list of the current parameters.
2.
The Log messages in the device can prove a useful diagnostic tool for troubleshooting.
Go to Setup > Maintenance > System Log > LOG LIST > message.
2010/2 ‐ 1 01B.00
24

Public link updated
The public link to your chat has been updated.
Advertisement