XSNet S4124SW

Quick Start Guide

Power

Steady Power on

This quick start guide describes how to install and use the Managed Ethernet Switch.

Functional Description



RS-232 console, Telnet, SNMP v1 & v2c & v3, RMON, Web Browser, and TFTP management.



Supports Command Line Interface in RS-232 console.



Supports 8192 MAC addresses. Provides 3M bits memory buffer.



IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation: 1000Mbps-full-duplex;

10/100Mbps-full/half-duplex; Auto MDI/MDIX.



The S4124SW is equipped with 24x 100Base-TX ports.



The S4124SW SFP is equipped with 24x 100Base-FX SFP slots.



Both S4124SW and S4124SW SFP are equipped with 4x combo back bone ports with per port a

10/100/1000Base-TX port or 1000-FX SFP slot.



Store-and-forward



Full wire-speed forwarding rate.



AC inlet power socket: 100~240VAC, 50~60Hz internal universal PSU.



Supports redundant power supplies for flexible application.



-10°C to 60°C (14°F to 140°F) operating temperature range. Tested @ -20°C to 70°C (-4°F to

158°F).

 case.



Supports Rack Mounting installation.

Physical Description

The Port Status LEDs and Power Inputs

10/100Base-TX, 100Base SFP

Link/ACT

Steady A valid network connection established

Flashing

Transmitting or receiving data

ACT stands for ACTIVITY

10/100/1000Base-TX, 1000Base SFP

Link/ACT

Steady A valid network connection established

Flashing

Transmitting or receiving data

ACT stands for ACTIVITY

SFP

Steady A valid SFP connection established

SFP

Console Configuration



Connect to the switch console:

Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of the terminal or computer running the terminal emulation application. Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal) to the switch console port.



Configuration settings of the terminal-emulation program:

Baud rate: 115,200bps, Data bits: 8, Parity: none, Stop bit: 1, Flow control: none.



Press the “Enter” key. The Command Line Interface (CLI) screen should appear as below:



Logon to Exec Mode (View Mode):

At the “switch_a login: ” prompt just type in “root” and press <Enter> to logon to Exec Mode (or View

Mode). And the “switch_a>” prompt will show on the screen.



Logon to Privileged Exec Mode (Enable Mode):

1 V3

XSNet S4124SW

At the “switch_a>” prompt just type in “enable” and press <Enter> to logon to Privileged Exec Mode

(or Enable Mode). And the “switch_a#” prompt will show on the screen.



Logon to Configure Mode (Configure Terminal Mode):

At the “switch_a#” prompt just type in “configure terminal” and press <Enter> to logon to Configure

Mode (or Configure Terminal Mode). And the “switch_a(config)#” prompt will show on the screen.



Set new IP address and subnet mask for Switch:

At the “switch_a(config)#” prompt just type in “interface vlan1.1” and press <Enter> to logon to vlan 1

(vlan1.1 means vlan 1). And the “switch_a(config-if)#” prompt will show on the screen.

Command Syntax: “ip address A.B.C.D/M”. “A.B.C.D” specifies IP address. “M” specifies IP subnet mask. “M”= 8: 255.0.0.0, 16:255.255.0.0, or 24: 255.255.255.0.

For example, At the “switch_a(config-if)#” prompt just type in “ip address 192.168.1.10/24” and press

<Enter> to set new IP address (192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch.



Enter the factory default login ID: root.

Enter the factory default password (no password).

Then click on the “Login” button to log on to the switch.

Web Configuration



Login the switch:

Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be shown as below:

2 V3