advertisement
Surround Cinema
SUB200
Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 9/2004
SUB200 (SCS200 .7
sys)
Note: The SUB200 is part of the SCS200.7 system
Satellite loudspeakers SCS200SAT order JBL part# SCS200SAT-1
Center channel SCS200CEN order JBL part# SCS200/300CEN-1
- CONTENTS -
BASIC SPECIFICATIONS……………….….….….….…………….1
DETAILED SPECIFICATIONS ……..…………….……………..2
OPERATION ………….……………………………..…………….4
CONNECTIONS..………………………..………….…….………...5
BASIC TROUBLESHOOTING…..…………….….….…….……...7
TEST SET-UP AND PROCEDURE……..……….…….………….8
EXPLODED VIEW/PARTS LIST…………………………………..9
BLOCK DIAGRAM..…………………………………………….....10
PCB DRAWINGS………………..………………………………...11
ELECTRICAL PARTS LIST ……………………….……………..15
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS………….19
SCHEMATICS.………..…………………………………. ………20
PACKAGING…………………………….………………………...22
BASIC SPECIFICATIONS
SUB200 Subwoofer
Configuration:
Floor-firing, bass-reflex ported enclosure
Woofer:
8" (203mm) cone
Amplifier Power output:
100W Continuous RMS power
Frequency response:
35Hz – 160Hz (-6dB)
Dimensions (including feet):
16 1⁄4 x 11 x 13 3⁄4” (413 x 279 x 349mm)
Weight:
28 lb/12.7kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated
1
SUB200 (SCS200 .7
sys)
JBL SUB200 100W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120VAC/60Hz
Asia 100VAC/50Hz
EU 230VAC/50-60Hz
Parameter
Amp Section
Type (Class AB, D, other)
Type (Class AB, D, other)
Load Impedance (speaker)
Yes/No
Yes
Yes
Yes
Specification
AB
H
4
Hi/Lo Line
108-132
90-110
207-264
Unit
AB
H
Ohms
Unit
Vrms
Vrms
Vrms
Notes
Normal Operation
Normal Operation
Normal Operation
QA Test
Limits
N/A
N/A
N/A Nominal
Conditions
Rated Output Power 120V
Rated Output Power 230V
THD@ Rated Power
THD @ 1 Watt
DC Offset
Damping factor
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
Speaker/Hi Level Input
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
Residual Noise Floor
Residual Noise Floor
Input Impedance
Line input L&R , LFE
Speaker/Hi Level Input
Filters
Low Pass (fixed or variable)
Slope & Q
Subsonic filter (HPF)
Slope & Q
Limiter
(yes/no)
THD at Max. Output Power
Features
LFE Input
Volume pot Taper (lin/log)
ATO
Input Configuration
Line In (L,R)
Line level in LFE
Spkr/Hi Level In (L,R)
Spkr Out: Level out (L,R)Hi P
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input Frequency
ATO Level Line Level in (L,R
ATO Level Speaker in
100
105
0.5
0.1
10
>100
50
15
9.5
245
90
80
65
1.5
1
>10
4.7
fixed
YES
N/A
YES
LOG
YES
L ,R
LFE
L,R
L,R
YES
50
2
40
Watts
Watts
%
% mV-DC
DF
Hz mVrms mVrms mVrms dBA dBr dBr mVrms mVrms(max)
K ohms
K ohms
-dB/Octave
Hz dB/Octave
--
--
Hz mV mV
--
--
--
--
85
100
1
0.3
50
50
Functional
Functional
Functional
Functional
Functional
Functional
Functional
Functional
Functional
Functional
2mV@50Hz into Line Input w/ 1 ch. driven
Functional
2
Notes
120V System is Class AB
230V System is Class H
Different output power due to differences in amp configuration between 120V and
230V
50
±2dB
±2dB
±2dB
85
80
60
2.5
2
N/A
N/A
Nominal Freq.
To 1 Watt
To 1 Watt
To 1 Watt
Nominal over the audio BW
Nominal over the audio BW
1 input driven
LFE input driven only
(-20 dB below Line In)...1 input driven
To Rated power
To Rated power
To 1 Watt
Volume @max, using RMS reading
DMM/VOM (or A/P)
Volume @max, w/ A/P Swept
Bandpass Measurement (Line freq.+ harmonics)
A-Weighting filter
22KHz filter
22KHz filter
Reference only
Reference only
±2dB
N/A
±2dB
N/A
N/A
N/A
@ Nominal input voltage
@ Nominal input voltage
22K filter
22K filter
@ Speaker Output
Normal operation, MOMS required
Measured at speaker terminals, Output power 90 Watts THD 0.1 %
BW Limited to 500 Hz, refer to
ECR00031 & AP Curves
RCA inputs: L , R Summed to Mono
L R Summed to Mono
Direct by pass from Speaker in
SUB200 (SCS200 .7
sys)
Parameter
ATO Turn-on time
Auto Mute/ Turn-OFF Time
Power on Delay time
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
Efficiency
Specification
5
15
3
Unit ms minutes sec.
5
50
50 mV-peak mV-peak mV-peak
Stand-by Input Power
Power Cons.@rated power
Power Cons.@rated power
Protection
Short Circuit Protection
Thermal Protection
DC Offset Protection
Line Fuse Rating
120VAC
230VAC
12
180
195
YES
65 deg. C
YES
Watts
Watts
Watts
--
--
--
2.5
1.25
Amps
Amps
QA Test
Limits
Functional
Functional
Conditions
Amp connected and AC on, then input signal applied
T before muting, after signal is removed
Notes
Auto turn of time (T) must be 10 > T <15
Functional AC Power Applied
10
100
100
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
13
187
200
@ nom. line voltage
@ 120V-60 Hz (Nom.line voltage)
@ 230V-50 Hz (Nom.line voltage)
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Maximum allowable input power under nominal Input voltage and frequency,
HOT or COLD operation.
90 Watts @ 4 Ohms nominal line voltage
90 Watts @ 4 Ohms nominal line voltage
Functional Direct short at output
Functional @1/8 max unclipped Power
Functional DC present at Speaker Out leads
Type-T or Slo Blo
Type-T or Slo Blo
Temperature rise should not exceed 35K rise
Relay or crowbar (for driver/fire
External fuse with UL/SEMKO rated holder
External fuse with UL/SEMKO rated holder
3
SUB200 (SCS200 .7
sys)
OPERATION
Move the Master Power switch (marked “Power” å ) to the “•” (On) position to use the SUB200 subwoofer.
If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the
Master Power switch å to the Off position.
∫
å
VOLUME
Subwoofer
Level
MIN MAX
Subwoofer
Level
10
MIN MAX
4
Volume may be adjusted using the Subwoofer Level control ∫ as shown.
SUB200 (SCS200 .7
sys)
DOLBY* DIGITAL OR DTS ®
(OR OTHER DIGITAL SURROUND MODE) CONNECTION
RECEIVER
LFE OUT
SUBWOOFER
LINE
LEVEL
IN
LFE L R
Use this installation method for Dolby Digital, DTS or other digital surround processors:
Use the line-level input jack marked “LFE” for the Low-
Frequency Effects channel.
Connect this jack to the LFE output or subwoofer output on your receiver or amplifier.
Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
Make sure that you have configured your surround sound processor for “Subwoofer On.” Also configure your receiver for 5.1-, 6.1- or
7.1-channel operation as appropriate. The front left, front right, center and rear speakers should all be set to
“Small.” If your receiver allows you to set the crossover frequency between the subwoofer and the main speakers, select 120Hz or the setting that is the closest frequency below it.
DOLBY PRO LOGIC* (NON-DIGITAL) – LINE LEVEL
Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volumecontrolled preamp (line-) level output:
Left Front
– +
Left Surround
– +
Center
– +
Use RCA-type interconnects to connect the line-level subwoofer outputs on your receiver or amplifier to the line-level inputs on the subwoofer. IMPORTANT: Do not use the LFE input on the subwoofer with Dolby Pro Logic processors.
Left
Surround
– +
Left
Front
– +
Subwoofer
Line-
Level In
L
R
Receiver
Subwoofer
Out
R L
– +
Right
Front
– +
Center
Surround Back
Left
– +
Surround Back
Right
– +
Right
Surround
– +
Surround Back
Left
– +
Surround Back
Right
– +
Right Front
– +
Right Surround
– +
NOTE: If your receiver or amplifier only has one subwoofer output jack, then you will need to use a Y-connector (not included). Plug the male end of the Y-connector into your receiver or amplifier’s subwoofer output jack, and connect each of the two female ends to separate
RCA-type interconnects.
Finally, plug the RCA-type interconnects into the linelevel inputs on the subwoofer.
Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
Make sure your receiver or processor is correctly configured to indicate that the subwoofer is “On.”
Note for advanced users: If your receiver/processor has a built-in low-pass crossover filter for the subwoofer output, you may use the LFE input to bypass the subwoofer’s internal crossover.
8
5
SUB200 (SCS200 .7
sys)
DOLBY PRO LOGIC (NON-DIGITAL) – SPEAKER LEVEL
Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor does not have a subwoofer output, or a volume-controlled preamp (line-) level output:
Connect your receiver or amplifier’s front left and right speaker terminals to the left and right terminals on the subwoofer that are marked
“Speaker Level In.” Connect the left and right terminals on the subwoofer that are marked “Speaker Level Out” to the corresponding terminals on the back of your front left and right speakers.
Connect your receiver or amplifier’s center, surround and surround back speaker terminals to the corresponding terminals on the back of your center and surround speakers.
Left Front
– +
Left Front
– +
Left Surround
– +
+
R
–
–
L
+
Center
– +
Subwoofer
SPEAKER LEVEL
OUT IN
Receiver
Center
– +
Surround Back
Left
– +
+
R
–
–
L
+
Right Front
– +
Right Front
– +
Surround Back
Right
– +
Right Surround
– +
Left Surround
– +
Surround Back
Left
– +
Surround Back
Right
– +
Right Surround
– +
6
9
SUB200 (SCS200 .7
sys)
TROUBLESHOOTING
If there is no sound from any of the speakers:
• Check that receiver/amplifier is on and a source is playing.
• Check that the powered subwoofer is plugged in, and its Power switch å is switched on (“•” position).
• Check all wires and connections between receiver/ amplifier and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other.
• Review proper operation of your receiver/amplifier.
If there is no sound coming from one speaker:
• Check the “Balance” control on your receiver/amplifier.
• Check all wires and connections between receiver/ amplifier and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other.
• In Dolby Digital or DTS modes, make sure that the receiver/processor is configured so that the speaker in question is enabled.
• Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem has followed the speaker, or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner’s manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www.jbl.com.
If there is no sound from the center speaker:
• Check all wires and connections between receiver/ amplifier and speaker. Make sure all wires are connected.
Make sure none of the speaker wires are frayed, cut or punctured, or touching each other.
• If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode.
• If your receiver/processor is set in one of the Dolby
Digital or DTS modes, make sure the receiver/processor is configured so that the center speaker is enabled.
If the system plays at low volumes but shuts off as volume is increased:
• Check all wires and connections between receiver/ amplifier and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other.
• If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.
If there is low (or no) bass output:
• Make sure the connections to the left and right “Speaker
Inputs” have the correct polarity (+ and –).
• Make sure the subwoofer is plugged into an active
7 electrical outlet, and is turned on (Power switch å in the “•” position).
• In Dolby Digital or DTS modes, make sure your receiver/processor is configured so that the subwoofer and LFE output are enabled.
If there is no sound from the surround speakers:
• Check all wires and connections between receiver/ amplifier and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other.
• Review proper operation of your receiver/amplifier and its surround sound features.
• Make sure the movie or
TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/amplifier has other surround modes you may use.
• In Dolby Digital or DTS modes, make sure your receiver/processor is configured so that the surround speakers are enabled. When five satellites are in use, remember to configure your receiver or processor for
6.1-channel operation, and when all six satellites are in use, configure your receiver or processor for 7.1 channels.
• Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or
DTS mode, and that you have properly selected that mode using both the DVD player’s menu and the DVD disc’s menu.
11
SUB200 (SCS200 .7
sys)
SUB200 Test Set Up and Procedure
Equipment needed:
• Function/signal generator
• Integrated
• Multimeter
• cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single LFE input.
2) Turn the LEVEL control on the UUT to completely counterclockwise (MIN).
3) Turn on generator; adjust to
100mV, 50 Hz
.
4) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. Turn LEVEL control full clockwise (MAX)
5) LED should Green; immediate and vigorous bass response should be heard and felt from port tube opening.
6) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
7) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator.
8) Turn on generator and adjust so that speaker level input at the amplifier is
2.0V, 50 Hz
. Turn LEVEL control full clockwise (MAX).
9) Green LED should light; immediate and vigorous bass response should be heard and felt from the port tube opening.
Sweep Function
1) Follow steps 6-8 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet (instructions on exploded view drawing); detach + and - wire clips.
2) Check DC resistance of woofer; it should be
3.4 ohms
±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is
5.0
V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
SUB200 (SCS200 .7
sys)
SUB200
Exploded View
SUB200 Cabinet
Not For Sale
Port Tube
249-ABS-00174
Amplifier Screw (10)
352-AM04020D210
SUB200 Amplifier
Not For Sale
Woofer Screw (8)
352-FM04020D605
8" Woofer DCR=3.4
Ω
20MF10DAG-DW04
Main Body Rubber Foot (4)
321-ABS-00008
Foot Screw (4)
352-HM04030D500
Rubber Foot Base (4)
321-ABS-00009
9
SUB200 (SCS200 .7
sys)
10
SUB200 (SCS200 .7
sys)
11
SUB200 (SCS200 .7
sys)
12
SUB200 (SCS200 .7
sys)
13
SUB200 (SCS200 .7
sys)
14
Capacitors
132-223ja03
135-3107m16
135-4688m50
130-2b102k503
130-2f104z503
130-3f473m503
130-s1101k503
132-104J503
132-223ja03
135-3105m50
135-3107m16
135-3226m50
135-3227m10
135-3227m16
135-3476m25
Semiconductors
192-027c1815gr
192-028a1015gr
192-1572n5551
192-1582n5401
197-031n4148
199-15000335
199-15000625
199-15001605
190-06m4558d
SUB200 (SCS200 .7
sys)
SUB200 120v Electrical parts List
Part Number Description
Main Amp PCB
Resistors
110-14472j26
110-14681j26
110-16101j26
110-16102j26
110-16103j26
110-16105j26
110-16123j26
110-16152j26
110-16153j26
110-16154j26
110-16181j26
110-16182j26
110-16223j26
110-16332j26
110-16392j26
110-16393j26
110-16470j26
110-16471j26
110-16472j26
110-16473j26
110-16560j26
110-16563j26
110-16682j26
110-10821jk2
110-122r2j15
110-20331jk2
113-50r10j10
114-03302m0
Qty Reference Designator
Resistor 4.7K 1/4W ±5% 26mm
Resistor 680 Ω 1/4W ±5% 26mm
2 R147,150
2 R148,151
Resistor10 0 Ω 1/6W ±5%CF 26mm 1 R120
Resistor 1K 1/6W ±5% CF 26mm 1 R124
Resistor 10K 1/6W ±5% CF 26mm 1 R134
Resistor 1M 1/6W ±5% CF 26mm 1 R143
Resistor 12K 1/6W ±5% CF 26mm 2 R135,139
Resistor 1.5K 1/6W ±5% CF 26mm CF 6 R103,123,136,137,141,142
Resistor 15K 1/6W ±5% CF 26mm 4 R118,145,152,154
Resistor 150K 1/6W ±5% CF 26mm 1 R131
Resistor 18 Ω 1/6W ±5% CF 26mm 2 R11,114
Resistor 1.8K 1/6W ±5% CF 26mm 1 R153
Resistor 22K 1/6W ±5% CF 26mm 3 R128,129,133
Resistor 3.3K 1/6W ±5% CF 26mm 3 R106,107,144
Resistor 3.9K 1/6W ±5% CF 26mm 2 R105,108
Resistor 39K 1/6W ±5% CF 26mm 1 R126
Resistor 47 Ω 1/6W ±5%CF 26mm 4 R112,113,115,116
Resistor 470 Ω 1/6W ±5% CF 26mm 1 R140
Resistor 4.7K 1/6W ±5% CF 26mm 3 R110,125,130
Resistor 47K 1/6W ±5% CF 26mm
Resistor 56 Ω 1/6W ±5% CF 26mm
Resistor 56K 1/6W ±5% CF 26mm
Resistor 6.8K 1/6W ±5% CF 26mm
Resistor 820 Ω 1W ±5% 10mm
Resistor 2.2
Ω 1/2W ±5% 15mm
Resistor 330 Ω 2W ±5% 5mm cement Resistor 0.1
Ω 5W ±5% semi-fixed Resistor 3K 0.3W 1±20%
1 R101
1 R117
1 R104
1 R109
1 R132
1 R127
2 R146,149
2 R121,122
1 R138 mylar capacitor 0.022uF 100V ±5% 2 C123,127 electrolytic 100uF 16V ±20% 1 C110 electrolytic 6800U/50V ±20% D25X45mm 2 C121,122 disc capacitor 1000p 50V±10% disc capacitor0.1u 50V+80/ -20% disc capacitor0.047u 50V±20% disc capacitor100p 50V SL±10% mylar capacitor 0.1u50V ±5%
1
4
1
2
1
C116
C108.113.115.119
C106
C139,140
C107 mylar capacitor 0.022uF 100V ±5% 4 C124,125,126,128 mylar capacitor 1U 50V ±20% 2 C105,112 mylar capacitor 100uF 16V ±20% 3 C109,117,120 mylar capacitor 22U 50V ±20% 2 C114,118 mylar capacitor 220U 10V ±20% 2 C129,130 mylar capacitor 220U 16V ±20% mylar capacitor 47U 25V ±20%
1 C111
1 C103 transistor 2SC1815GR NPN transistor 2SA1015GR PNP transistor 2N5551 NPN transistor 2N5401 AI-PNP 350V 500MA TO-92 diode 100mA 75V SIGNAL 1N4148 ROHM zener diode3.3V 1/2W 52mm zener diode 6.2V 1/2W 52mm zener diode 16V 1/2W 52mm
IC OPA 4558D DUAL OP-AMP
15
5 Q102,111,112,113,118
2 Q114,116
2 Q103,109
2 Q104,110
4 D101,103,105,108
1 D102
2 D106,107
1 D109
1 U101
SUB200 (SCS200 .7
sys)
Part Number Description
Main Amp PCB
192-021tip35c
192-022tip36c
192-027c1815gr
192-201d882Y
192-202b772y
192-991d669a
192-992b649T
197-00kb1405
197-101n4002 transistor TIP35C NPN transistor TIP36C PNP transistor 2SC1815GR NPN transistor KSD882Y PNP transistor KSB772Y PNP transistor HI-SINCERITY HSD669A NPN transistor HSB649T PNP diode 4A500V KBL405 BRIDGE diode IN4002
Qty Reference Designator
1 Q107
1 Q108
2 Q101,115
1 Q117
1 Q119
1 Q106
1 Q105
1 D110
1 D104
Miscellaneous
193-3m2520
162-10202001
171-udhss124d insulator TO-3P 25x20mm wire 26AWC 1007 200mm RED relay 5A 24V UDH-SS124D
2 for Q107,108
1
1 RY101
175-1c07v01
175-1d02v01
175-1d03v01
323-AL-00020 wire connector 7PIN PITCH=2.5mm wire connector 2PIN PITCH=3.96mm wire connector 3PIN PITCH=3.96mm
Heat sink 65*32*31
351-AM03014A094 screw
1
1
1
1
1
P101
P102
P103
352-AM03008D040 screw
361-FE-00051 transistor holder
361-NYL-00054 transistor sheet
4
1
2
Input/Preamp PCB
Resistors
110-12472j52
110-16102j26
110-16103j26
110-16104j26
110-16105j26
110-16122j26
110-16124j26
110-16151j26
110-16153j26
110-16154j26
110-16183j26
110-16205j26
110-16223j26
110-16273j26
110-16333j26
110-16472j26
110-16473j26
110-16512j26
110-16513j26
115-h503a104
Resistor 4.7K 1/2W ±5% CF 52mm
Resistor 1K 1/6W ±5% CF 26mm
Resistor 10K 1/6W ±5% CF 26mm
2
4
14
R201,202
R213,214,215,254
R209,212,216,217,220,221,222,225,228,226,232,235,240,248
Resistor 100K 1/6W ±5% CF 26mm 2 R231,266
Resistor 1M 1/6W ±5% CF 26mm 1 R259
Resistor 1.2K 1/6W ±5% CF 26mm 1 R264
Resistor 120K 1/6W ±5% CF 26mm 1 R233
Resistor 150 Ω 1/6W ±5% CF 26mm 1 R253
Resistor 15K 1/6W ±5% CF 26mm 1 R234
Resistor 150K 1/6W ±5% CF 26mm 5 R203,204,205,206,252
Resistor 18K 1/6W ±5% CF 26mm 2 R262,227
Resistor 2M 1/6W ±5% CF 26mm 1 R257
Resistor 22K 1/6W ±5% CF 26mm 4 R238,247,250,255
Resistor 27K 1/6W ±5% CF 26mm 2 R223,237
Resistor 33K 1/6W ±5% CF 26mm 1 R249
Resistor 4.7K 1/6W ±5% CF 26mm 4 R200,207,258,260
Resistor 47K 1/6W ±5% CF 26mm 2 R219,251
Resistor 5.1K 1/6W ±5% CF 26mm 4 R210,211,229,230
Resistor 51K 1/6W ±5% CF 26mm 1 R224
Variable resistor D16 50K/1 A LEVEL 1 VR201
Capacitors
130-2b221k503
130-2f104z503
130-sl470k503
132-103j503
132-104j503
132-223ja03
132-473j503
135-3105m50
135-3106m50
135-3107m16 disc capacitor 220P 50V ± 10% 12 C204,205,207,208,210,211,212,214,220,230,200,249 disc capacitor 0.1U 50V +80/-20% 7 C232,242,244,245,246,252,254 disc capacitor 47P 50V ± 10% 1 C229 electolytic 0.01U 50V ± 5% electolytic 0.1U 50V ± 5% electolytic 0.22uF 100V ± 5% electolytic 0.047U 50V ± 5% electolytic 1U 50V ± 20% electolytic 10uF 50V ± 20% electolytic 100uF 16V ± 20%
2
3
2 C216,217
1 C228
10
2
C223,224
C218,221,222
C215
C201,202,206,213,219,231,241,243,251,253
C233,234
16
SUB200 (SCS200 .7
sys)
Part Number Description
Input/Preamp PCB
135-3226m50 electolytic 22U 50V ± 20%
Semiconductors
192-027c1815gr
197-031n4148
199-15000335
190-06m4558d
190-16t1074cn
195-10204hgw transistor 2SC1815GR NPN diode 100mA 75V SIGNAL 1N4148 ROHM zener diode 3.3V 1/2W 52mm
I.C OPA 4558D DUAL OP-AMP
I .C TL074cm QUAD OP-AMP
LED 204HGW 3c
Qty Reference Designator
1 C225
3 Q201,206,207
11 D201,202,203,204,205,206,207,208,211,212,214
1 D213
1 U203
2 U201,202
1 D209
Miscellaneous
162-50159201
174-0rca326p
174-2psz406g1
174-2psz406g2
Limiter PCB
110-16103j26
110-16183j26
110-16223j26
110-16273j26
110-16333j26
110-16472j26
110-16474j26
110-16751j26
110-16755j26
130-2f104z503
132-103j503
135-3226m50
135-3476m25
192-027c1815gr
197-031n4148
162-50289001
175-9F40HR2
190-16tl074cn
WIRE ASS'Y 2PIN 150mm
JACK RCA-326 3 input
JACK S-8071
SPK JK 4PIN S-8072
1 for D209
1 JK202
1 JK203
1 JK203
Resistor 10K 1/6W ±5% CF 26mm 8 R301,303,304,308,309,314,340,344
Resistor 18K 1/6W ±5% CF 26mm 1 R302
Resistor 22K 1/6W ±5% CF 26mm
Resistor 27K 1/6W ±5% CF 26mm
Resistor 33K 1/6W ±5% CF 26mm
2
1 R341
1
R310,312
R305
Resistor 4.7K 1/6W ±5% CF 26mm 2 R342,343
Resistor 470K 1/6W ±5% CF 26mm 1 R307
Resistor 750 Ω 1/6W ±5% CF 26mm 2 R311,313
Resistor 7.5M 1/6W ±5% CF 26mm 1 R306 disc capacitor 0.1u 50V +80/-20% 2 C305,306 mylar capacitor 0.01U 50V ± 5% electolytic 22U 50V ± 20% electolytic 47U 25V ± 20% transistor 2SC1815GR NPN diode 100mA 75V SIGNAL 1N4148
2 C302,303
2 C301,340
1 C304
2 Q301,302
2 D301,302 wire CABLE ASS'Y280mm AWG26 1 wire connector 40PIN PITCH=2.54mm HR2*40 0.15 P301
IC TL074CN ST 1 U301
MISCELLANEOUS
130-3f472md00
123-14j70d
150-e8604107
152-u602015
154-u25006t0
155-520020
162-10082007
162-50652003
163-11009 disc capacitor 4700p 400V ± 20%
Ferrite Core U-16.3*8.2*13
Power Trans EI-86 60HZ 120V TT086996580
LineCord SVT FT-2 6FT
Fuse 2.5A 250V 20mm
Fuse Holder R3-11
WIRE RED 18AWG 80mm 8mm#1015
WIRE 650mm RED=205# 0.5T BLK=110# 0.5T
wire tie 100mm
176-wjcel
180-prf1003S wire connector Pin CE-1 switch ROCK RF-1003-BB2-OHA
302-AL-00406-0VC Alu. Panel
306-ABS-00177 Rear cover
311-ABS-00028 Plastic knob
302-RUB-00033
323-AL-00141
333-EVA-00783
333-EVA-00807
333-EVA-00826
333-EVA-00835
335-NYL-00002
Rubber cusion
Heat sink
EVA (Gasket)
EVA (Gasket)
EVA (Gasket)
EVA (Gasket)
Cable ring
17
2
2
4
1
2
2
2
1
1
1
1
1 On Power Switch
1
1 T1
1
1
1
1
2
1
1 SW100
SUB200 (SCS200 .7
sys)
Part Number Description
MISCELLANEOUS
337-CU-00101 Rubber sheet
350-EM04012D024 Screw
351-AM03008A079 Screw
351-BM03012A088 Screw
351-HM04016A218 Screw
352-AM03008D040 Screw
352-AM03010D065 Screw
354-GM04002
361-FE-00051
362-FE-00013
Screw nut
IC holder
PCB holder
Qty Reference Designator
4
1
8
5
2
6
1
1
4
4
18
SUB200 (SCS200 .7
sys)
19
SUB200 (SCS200 .7
sys)
R306
20
SUB200 (SCS200 .7
sys)
STANDBY DELAY
Adjustment Procedure for R138:
Use DC voltmeter attached to R140, adjust R138 until the meter reads
510mV (+/-2mV)
460mV (+/-2mV)
(for 120v model)
(for 230v model) then use "LOCTITE" to fix R138.
21
SUB200 (SCS200 .7
sys)
Speaker Wire 20 Feet (3)
166-020F84XX
Speaker Wire 40 Feet (4)
166-040F84XX
Speaker Wire 15 Feet (2)
166-015F84XX
RCA Cable 15 Feet
166-015F011
Floor Stand Adapter (6)
325-ABS-00436
Wall-Mount Bracket
(Sats & Center) (7)
326-ABS-05013
Center Shelf Stand
398-ABS-05043
Sat Shelf Stand (6)
398-ABS-05041
Hardware Bag A
371-000-05019
Hardware Bag B
371-000-05027
Screw (6)
354-GC250703
SUB200
Packaging
Warranty Card
405-000-00258
Owner’s Manual
406-000-00956
SCS200.7 Outer Carton
402-000-01821
22
advertisement
Related manuals
advertisement