Ganz ZN-DNT350VP(N)E, ZN-DWNT350VP(N)E Installation Manual
Ganz ZN-DWNT350VP(N)E is a fixed vandal-proof dome IP camera with a 1/3” vertical double density color CCD. It supports a 25/30FPS streaming function at D1 resolution in both PAL/NTSC, and a dual streaming mode feature with varying codec/resolution/bit rate. The camera also features True Day / Night (ICR) capability for improved color rolling suppression, VCA Presence (included as basic) and VCA Surveillance (optional), and built-in video content analysis.
Advertisement
Advertisement
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
!
!
This symbol is intended to alert the user to the presence of un ‐ insulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
Table of Contents
1.
FEATURES ............................................................................................................... 4
2.
PACKAGE CONTENTS .............................................................................................. 5
3.
PART NAMES .......................................................................................................... 6
3.1.Internal
View ....................................................................................................................... 6
4.
INSTALLATION ........................................................................................................ 7
4.1.
Installation Template ......................................................................................................... 8
4.2.
Manual adjustment for 3 ‐ axis movements ........................................................................ 9
4.3.
Setting the Image Attribute................................................................................................ 9
4.4.
Operating the OSD Menu................................................................................................... 9
5.
CONNECTIONS ...................................................................................................... 10
5.1.Connectors ........................................................................................................................ 10
6.
CONFIGURATION .................................................................................................. 13
6.1.Set
up network environment ............................................................................................ 13
6.2.
View video on web page .................................................................................................. 13
6.2.1.
View video using ZNS ‐ GIT IPAdmin Tool ................................................................... 13
6.2.2.View
video using IP address ....................................................................................... 16
6.3.
Reset................................................................................................................................. 16
6.4.
Factory Default................................................................................................................. 16
APPENDIX (A): SPECIFICATIONS ................................................................................ 17
Summary ................................................................................................................................. 17
Electrical Characteristics ......................................................................................................... 18
Environment Condition ........................................................................................................... 18
VCA (Video Content Analysis) ................................................................................................. 19
APPENDIX (B): POWER OVER ETHERNET................................................................... 20
PoE compatibility .................................................................................................................... 20
Power classification................................................................................................................. 20
APPENDIX (C): DIMENSIONS ..................................................................................... 21
APPENDIX (D): ACCESSORIES .................................................................................... 21
APPENDIX (E): TROUBLE SHOOTING ......................................................................... 22
Checking your Firmware ......................................................................................................... 22
Support.................................................................................................................................... 22
2010/2 ‐ 1 03A.02
3
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
1. FEATURES
Camera
•
Indoor/Outdoor Fixed Dome IP Camera (Vandal Proof)
•
High Quality Compression in real time streaming
•
Sony 1/3” Super HAD CCD & High Quality SS ‐ HQ1 Full Kit Chip Set
Sony 1/3" Vertical Double Density Color CCD (Optional)
• True Day / Night (ICR) and WDR (Optional)
•
Improvement of color rolling suppression
Streaming
•
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
•
De ‐ interlacing on DSP
•
Burnt ‐ in text supported
•
Unicast/Multicast supported
Video/Audio
•
Video compression: H.264/MPEG/MJPEG, 25/30FPS@D1(PAL/NTSC)
• Audio compression: G.711(µLaw, aLaw)/PCM
•
Analog video out for external monitors
•
Video Motion Detection supported
•
2 ‐ way mono audio supported
Network
•
RTSP/ HTTP protocol supported
•
10/100 Base ‐ T Ethernet
Additional Features
•
RS ‐ 485 supported
•
Micro SD card supported
•
PoE supported
•
Built ‐ in Video Content Analysis
•
OSD supported
•
SDK (Software Development Kit) provided
VCA (Video Content Analysis)
•
VCA Presence (Included as basic)
•
VCA Surveillance (Optional)
2010/2 ‐ 1 03A.02
4
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care.
The packaging contains:
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE DC power adaptor
Extension cable
(for LAN and power connector)
11 Pin terminal block
Screws and Anchor blocks Hex wrench driver
Installation Template
Quick Installation Guide
Video BNC Cable
Surface Cushion
(for protection against dust)
i
Note
The above contents are subject to change without prior notice.
2010/2 ‐ 1 03A.02
5
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
3. PART NAMES
3.1.Internal View
④
③
②
①
* Models herein and their appearance
⑤ ⑥ are subject to change without any prior notice.
① 11 pin terminal block for D/I, D/O, audio, and serial communication
11 pin terminal block for D/I, D/O, Audio in /Out and serial communication.
Refer to the
section “ 5.1.Connectors” for more specific information.
② Reset
Reset switch is used for restarting ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE or resetting
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE to Factory Default (FD).
Refer to the section “ 6.3.
Reset” for more specific information.
③ Micro SD Card Socket
It is a memory card slot for external storage.
④ Extension cable Socket
It is a socket for LAN and power connector.
⑤ LAN Connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base ‐ T Ethernet.
This socket can also be used to power the ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE via PoE (Optional).
⑥ Power Adaptor Connector (DC 12V)
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE needs a DC 12V 1A adapter for power supply.
2010/2 ‐ 1 03A.02
6
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
4. INSTALLATION
1) Connect the LAN cable, power supply cable, and the video loop out cable
with the ZN ‐ DT350VE/ZN ‐
DNT350VE/ZN ‐ DWNT350VE.
2) Place the installation template on the
ceiling.
3) Drill three holes on the template and insert anchor blocks into the holes.
Fasten the ZN ‐ DT350VE/ZN ‐
DNT350VE/ZN ‐ DWNT350VE with
screws.
4) Put the dome cover on the main body of the ZN ‐ DT350VE/ZN ‐
DNT350VE/ZN ‐ DWNT350VE.
Make sure the main body and the cover fit each
other into place.
5) Fasten the cover with screws.
i
Note
When assembling the main body of the ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐
DWNT350VE and its dome cover, make sure they fit each other into place.
2010/2 ‐ 1 03A.02
7
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
!
Caution
The ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE may fall off the ceiling even after the proper installation and mounting.
To prevent any accident, make sure the ceiling is firm and stable enough to support the ZN ‐ DT350VE/ZN ‐
DNT350VE/ZN ‐ DWNT350VE.
If any reinforcement is needed, consult with your safety personnel and proceed with the installation.
4.1. Installation Template
2010/2 ‐ 1 03A.02
8
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
4.2. Manual adjustment for 3-axis movements
After installation, make a manual adjustment on the inner liner.
Perform 3 ‐ axis movements
manually by turning the inner liner to different directions as above, and check if it moves properly.
4.3. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video ‐ in > Attribute
Setting .
Brightness, contrast, hue, saturation and sharpness can be adjusted.
4.4. Operating the OSD Menu
To operate the OSD of camera, refer to the ” OSD Menu Control Manual ” in the SDK.
2010/2 ‐ 1 03A.02
9
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
5. CONNECTIONS
5.1.Connectors
① Audio In / Out
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE has a mono audio input and a mono audio output.
As the output power for the audio is low, amplifier speaker is needed (Do not use a headphone or earphone directly to the camera).
Aout Ain
Mic
Amp Speaker
② Sensor (DI) connection
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE provides 1 channel D/I.
It can be connected to either a voltage type sensor or a relay type sensor as the following figures.
It can be selected by software.
Input voltage range: 0 VDC minimum to 24 VDC maximum
Input voltage threshold: 1 V
!
Caution
Do not exceed the maximum input voltage or relay rate.
2010/2 ‐ 1 03A.02
10
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
Internal +5V
DI
Output of
Sensor
+ ‐
Internal
DI
Output of
Sensor
+ ‐
COM
COM ‐ +
Relay Type
③ Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VAC 500mA or 12VDC 1A
!
Caution
Do not exceed the maximum relay rating.
Internal
DO
Device
Voltage Type
COM
Relay Type
④ Video Out
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE provides 1 video loop out.
GND Video
Black White
2010/2 ‐ 1 03A.02
11
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
⑤ RS ‐ 485
The RS ‐ 485 serial port consists of TRX+(RX+) and TRX ‐ (RX ‐ ) as following the following image.
RS ‐ 485 Connection
485 Device
2010/2 ‐ 1 03A.02
12
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
6. CONFIGURATION
6.1.Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX.
You can find the available IP address from the MAC address of your device.
Please make sure the device and your PC are on the same network segment before running the installation.
If the network segment between your PC and the device is different, change your PC’s settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.2. View video on web page
View the live video on a web page using your IP device and its IP address.
You can use the ZNS ‐
GIT IPAdminTool or enter the IP address on the web page.
6.2.1. View video using ZNS-GIT IPAdmin Tool
ZNS ‐ GIT IPAdminTool automatically searches all activated GANZ network camera and encoder series and shows the product name, IP address, MAC address and etc.
ZNS ‐ GIT IPAdminTool is
provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
2010/2 ‐ 1 03A.02
13
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
To use the ZNS ‐ GIT IPAdminTool and view the live video on a web page:
1.
Start ZNS ‐ GIT IPAdminTool.
Names and info of currently activated devices appear as a list.
2.
Right ‐ click on the desired device and select Web view .
3.
Select Continue to this website on the Security Certificate Alert page.
(The explanation and captured images at this manual are mainly on the basis of Internet
Explorer 7.0)
4.
Click pop ‐ up blocked and install the ActiveX control as below.
You need to install the
ActiveX for displaying the images.
2010/2 ‐ 1 03A.02
14
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
5.
Wait for a few seconds while the web page loads.
The live video is displayed as below.
6.
If the live video is not displayed and “Can not Create XMLDOMDocument Install
MSXML4.0” message is shown as below, please download and Install from the link below.
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B ‐ B4F2 ‐ 46DA ‐
B4B6 ‐ C5D7485F2B42&displaylang=en
(VCA Library requires MS XML 4.0
library which is an xml parser made by Microsoft.)
2010/2 ‐ 1 03A.02
15
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
6.2.2.View video using IP address
View the live video on a web page using your IP device and its IP address.
To have the correct
IP address ready and use it on a web page:
1.
Convert a MAC address to an IP address or check the IP address on the ZNS ‐ GIT IPAdminTool.
(The MAC address is attached on the side or bottom of the device.)
MAC address = 00 ‐ 1 C ‐ B8 ‐ C0 ‐ 14 ‐ B1 → IP address = 192.168.20.177
the Hexadecimal number to Decimal number.
2.
Open a web browser and enter the IP address of the device.
3.
Click Continue to this website on the Security Certificate Alert page.
4.
Click pop ‐ up blocked and install the ActiveX control as below.
You need to install the ActiveX for displaying the images.
5.
Wait for a few seconds while the web page loads.
The live video is displayed.
6.3. Reset
1.
While the device is in use, press and hold the Reset button.
2.
Release the Reset button after 3 seconds.
3.
Wait for the system to reboot.
6.4. Factory Default
1.
Disconnect the power supply from the device.
2.
Connect the power to the device with the Reset button pressed and held.
3.
Release the Reset button after 5 seconds.
4.
Wait for the system to reboot.
The factory default settings can be inferred as follows:
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway:
User ID:
Password:
192.168.0.1
root pass
2010/2 ‐ 1 03A.02
16
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
CCD
Sync
ELECTRICAL
Model
Day &
Image
S/N (Y
Sensor
Effective
Resolution signal)
Min.
Illumination
Wide Dynamic
Range
Color
AGC Control
White Balance
Shutter
Lens
Night
Pixels
Frequency
Electronic
Sens ‐ Up
DNR
Speed
Size
Scanning system
ZN ‐ DT/DNT350VE
Sony 1/3” Super HAD
CCD, 410K Pixel
ZN ‐ DWNT350VE
SONY 1/3" Vertical Double
Density Color CCD
NTSC: 768(H) x 494(V)
PAL: 752(H) x 582(V)
1/3 inch interline transfer CCD
2:1 Interlace
540
50dB
TV
NTSC: 15.734
KHz (H) 59.94
Hz(V)
PAL:15.625
KHz(H) 50.00
Hz (V)
Lines
(AGC
Off)
0.3Lux/F1.2(Color),
01.Lux/F1.2(B/W),
0.002Lux
(Sens ‐ up)
560 TV lines (Color),
600 TV lines (B/W)
52dB (AGC Off)
0.3Lux/F1.2(Color),
0.03Lux/F1.2(B/W)
Not supported 52dB(x128)
ON/AUTO
OFF/LOW/MIDDLE/HIGH Selectable
ATW/AWC/MANUAL (1,800° K~10,500° K)
(NTSC:
PAL:
AUTO/
MANUAL
1/60~1/120,000,
1/50~1/120,000)
AUTO/
MANUAL
(NTSC: X256~1/60sec~
1/120,000sec,
PAL: X256~1/50sec~
1/120,000sec)
Sens ‐ up and Sens ‐ up Limit is selectable / Flickerless
OFF/AUTO
OFF/LOW/MIDDLE/HIGH
(Noise Reduction)
ON (Level 0~32) /
OFF Selectable
2.8~10.5
mm F1.2
DC Auto Iris Board Vari ‐ Focal
SW (ZN ‐ DT350VE)
IR Cut Filter Remove
(ZN ‐ DNT350VE)
IR Cut Filter Remove
Video
Compression Format
Number of Streams
H.264, MPEG ‐
Dual
4,
MJPEG
Stream,
Selectable per
Configurable
Stream
2010/2 ‐ 1 03A.02
17
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
Resolution
Compression FPS
Deinterlacing
Burnt ‐ in Text (Digital)
Output
Audio
Motion Detection
OSD
Input/output
Compression Format
Function
Digital Input/output
RS ‐ 485
Network
Power over Ethernet
D1, 4CIF, VGA, CIF, QCIF
25/30 fps@D1 (PAL/NTSC)
Supported (DSP)
Supported
Supported (DSP)
Supported (DSP)
1 Loop Out (BNC connector)
1/1 channel
G.711
Protocol
SD Slot
Material
Dimensions
Color
1/1 channel
Supported
10/100 Base ‐ T
Supported
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP,
SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP,
FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH
Supported (MicroSD)
※ Micro SD Card is not included
Aluminum Die Casting ‐ 2
Housing : 150.8(Ø) 113(H) mm
Dome : 100(Ø) mm
White Pearl
Electrical Characteristics
Video Output
Audio Input
Audio Output
Sensor(D/I)
Alarm(D/O)
Power Source(Approx)
1Vp ‐ p, 75 Ω
Linein, 1.43Vp
‐ p(Min 1.35Vp
‐ p, max 1.49
Vp ‐ p), 39 K Ω
Lineout, 46mW Power, 16 Ω
TTL level 4.5V
threshold, Max 50mA
Max 500mA@24VAC or 1A@12VDC
12 V DC 300 mA or PoE IEEE802.3af
(Class 0)
Environment Condition
Operating Temperature
Operating Humidity
0 ˚ C ~ 50 ˚ C (32 ˚ F ~ 122 ˚ F)
Up to 85% RH
2010/2 ‐ 1 03A.02
18
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
VCA (Video Content Analysis)
VCA Presence (Included as Standard)
High Performance Advanced Tracking Algorithm, Low False Alarm Rate
Easy to Use
Detection Zones
On ‐ screen Display
Intuitive
Multi ‐
Web segment
Browser
Interface
Polygons and
Lines
Burnt ‐ in Annotation
Real ‐ time Display of Tracking Data and Events
Stream or Analog video out
( ※ Analog video out support can vary depending on the device model and hardware version and the firmware version)
VCA Surveillance (Optional)
Detection Behavior
Camera Tampering, Direction, Stopping, Loitering, Entering,
Exiting, Appear, and Disappear Filters
3D Behavior Perspective Corrected Size and Speed Filters
Statistics
Meta Data
Image Stabilization (Optional)
Electronic Stabilization
Counting Functions and Other Statistics
Binary XML Format
Removes Camera Sway
2010/2 ‐ 1 03A.02
19
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
APPENDIX (B): POWER OVER ETHERNET
The Power over Ethernet(PoE) is designed to extract power from a conventional twisted pair
Category 5 Ethernet cable, conforming to the IEEE 802.3af
Power ‐ over ‐ Ethernet (PoE) standard.
IEEE 802.3af
allows for two power options for Category 5 cables.
The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by the Power Sourcing Equipment (PSE) before applying up to
15W power to the port.
The high efficiency DC/DC converter operates over a wide input voltage range and provides a regulated low ripple and low noise output.
The DC/DC converter also has built ‐ in overload and short ‐ circuit output protection.
PoE compatibility
With non Power Sourcing Equipment (PSE)
When it is connected with non PSE, the power adaptor should be connected.
With power adaptor
Connecting both PSE and power adaptor does not do any harm to the products.
Disconnecting power adaptor while it is operating does not stop operation.
The product continues to work without rebooting.
Power classification
The PoE Power Class supported by the IP device is Class 0.
Class Usage Minimum Power Levels
Output at the PSE
0 Default 15.4W
Maximum Power Levels at the
Powered Device
0.44
to 12.95W
2010/2 ‐ 1 03A.02
20
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
APPENDIX (C): DIMENSIONS
2010/2 ‐ 1 03A.02
(Unit: mm)
21
ZN ‐ DT350VE/ZN ‐ DNT350VE/ZN ‐ DWNT350VE Installation Guide
APPENDIX (E): TROUBLE SHOOTING
Checking your Firmware
Firmware is software that determines the functionality of the device.
One of your first actions when troubleshooting a problem should be to check the currently installed version.
The latest version may contain a correction that fixes your particular problem.
The current firmware version in your device can be seen under Setup > About > Version
New firmware can be downloaded at the FTP site.
When you download firmware from the FTP, your product will receive the latest available functionality.
Always read the upgrade instructions and release notes available with each new release, before updating the firmware.
Please contact us to get an FTP account.
Support
If you cannot resolve an issue, for additional assistance, please contact your supplier or system integrator.
If you contact our support, please help us help you resolve your problems expediently by providing a server report, log file and a brief description of the problem.
1.
In the address bar of your browser, after the unit IP address enter following CGI command.
<IP ADDRESS> /nvc ‐ cgi/admin/param.cgi?action=list
The server report contains important information about the device, as well as a list of the current parameters.
2.
The Log messages in the device can prove a useful diagnostic tool for troubleshooting.
Go to Setup > Maintenance > System Log > LOG LIST > message.
2010/2 ‐ 1 03A.02
22
Advertisement
