VIKING
Electronics, Inc.
QUICK START GUIDE
K
See Product Manual for complete installation and programming instructions.
1.0 Out-of-Box
E-60-BK-IP or
E-60-BK-IP-EWP
VoIP Entry Phone
September 25, 2018
1.1 Verify that you have received all of the parts listed
X 1
E-60-BK-IP or E-60-BK-IP-
EWP Entry Phone
X 1 Face Plate Black
X 1 Faceplate Gasket
X 1 Light Pipe
X 4
X 4
6-32 x 1.25” Flat Head Hex
Drive Screws Black painted
6-32 x 3/4” Flat Head Hex
Drive Screws
X 1 Hexkey 5/64
X 2 Plate Adapter
X 5 Gel-Filled Butt Connectors
1.2 Download the product manual
Scan the QR code to open and download the product manual
- OR -
1. Go to www.vikingelectronics.com
and enter E-60-BK-IP in the search box
2. Click E-60-BK-IP in the search results
3. Click Product Manual to open and download the PDF
1.3 Download and install the programming software
1. Go to www.vikingelectronics.com
and enter E-60-BK-IP in the search box
2. Click E-60-BK-IP in the search results
3. Scroll down the page to Downloads, click IP Programming Software
4. Install the programming software by saving or opening the file and then clicking on setup Viking IP Programming.exe
5. Follow the prompts on your screen to complete software installation
2.0 Power Source
Select PoE Switch or PoE Injector that meets the following requirements:
1. IEEE 802.3af / 802.3at / 802.3bu compliant
2. Capable of providing at least 4 Watts (class 1)
Note: CAT5e (or higher) cable recommended
3.0 Network Port Settings
• Make sure the port is not in trunk mode
• Make sure port is capable of 100mbps full duplex
• Disable Spanning Tree Protocol (STP) or enable Portfast
4.0 Features Overview
Rear (PCB) View of E-60-IP
PoE LAN Port 10/100, PoE
Class 1 (<4 Watts): Connect to your LAN via RJ45 plug and CAT5 or greater twisted pair wire.
Green Unit Status LED
Yellow Network Status LED:
Lights steady to indicate power and data link. Blinks to indicate network activity.
MAC Address Label: The
MAC address is aunique 12 digit number used by routers to send network traffic to the correct IP address.
Connect to Optional
Doorstrike, Mag Lock,
Gate Controller, etc.
120V AC
(not connected)
Doorstrike /
Magnetic Lock
(Power typically not required for gate controllers)
* On-Board 2 Amp
Relay Output Contacts
(2A@30VDC/ 250VAC max)
N.C. (Gray)
COM. (Blue)
N.O. (Yellow)
3 Gel-Filled Butt
Connectors (included)
- Black
+ Red
Black
Black
Green
Green
White
White
- Black
+ Red
LED
Help Switch
Request for Exit (REX Input)
Speaker
Microphone
Note:
The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082 inches. Cut off stripped wire ends before terminating.
* Note:
For applications requiring additional security, a Viking model
RC-4A remote relay controller can be used. The relay controller is mounted securely inside the building and connected to the same LAN as the
E-60-BK-IP
. For more information on the
RC-4A
Secure Relay Controller, see
DOD 582
.
See the Product Manual for complete installation and programming instructions.
Questions? Call Viking Product Support: 715-386-8666
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
E-60-BK-IP Quick Start Guide ZF303684 REV A
