CreamWare Pro-12 Klangbox Benutzerhandbuch
Advertisement
Advertisement
Pro-12
Klangbox
Disclaimer
Pro-12 Klangbox is manufactured by CreamWare Audio GmbH, Siegburg, Germany.
(C) CreamWare 1999 - 2006 - all rights reserved.
The following documentation, compiled by CreamWare Audio GmbH (henceforth called CreamWare), represents the current state of the described product. The documentation may be updated on a regular basis. Any changes which might ensue, including those necessitated by update specifications, are included in the latest version of this documentation. CreamWare is under no obligation to notify any person, organization, or institution of such changes or to make these changes public in any other way.
We must caution you that this publication may include technical inaccuracies or typographical errors.
CreamWare offers no warranty, either expressed or implied, for the contents of this documentation. You will find the warranty regulations for the product at the end of this documentation.
In no event will CreamWare be liable for any loss of data or for errors in data use or processing resulting from the use of this product or the documentation. In particular, CreamWare will not be responsible for any direct or indirect damages (including lost profits, lost savings, delays or interruptions in the flow of business activities, including but not limited to, special, incidental, consequential, or other similar damages) arising out of the use of or inability to use this product or the associated documentation, even if CreamWare or any authorized CreamWare representative has been advised of the possibility of such damages.
The use of registered names, trademarks, etc., in this publication does not imply, even in the absence of a specific statement, that such names are exempt from the relevant protective laws and regulations (patent laws, trademark laws etc.) and therefore free for general use. In no case does CreamWare guarantee that the information given in this documentation is free of such third-party rights.
Neither this documentation nor any part thereof may be copied, translated, or reduced to any electronic medium or machine form without the prior written consent from CreamWare Audio GmbH.
This product (and the associated documentation) is governed by the GTC (General Terms and Conditions) of
CreamWare Audio GmbH.
Index
Owner’s Manual
Disclaimer
Index
Introduction
Getting started
Making connections
Power adaptor
MIDI connection
Audio connection
Power switch
USB connection and drivers
Installation of Remote Software
Presets
Remote Software (Main Page)
Oscillator A & B
Filter Section
Amplifier
LFO / Modulation
Glide / Unison
Remote Software (Add/Effects Page)
Add page
Effects Page
Prefs Page
MIDI Monitor
MIDI Keyboard
Preset administration
Specifications
MIDI implementation table
Specifications
Warranty regulations
CE certificate
19
24
26
28
29
30
32
33
34
34
9
11
13
15
18
6
6
6
6
7
5
5
5
2
3
4
3
Introduction
Welcome
Thank you for choosing the PRO-12 Klangbox. We hope you will have as much fun with your PRO-12 as we did when developing this unique and characterful synthesizer. Please read this manual thoroughly in order to take full advantage of the many features the
PRO-12 has to offer.
Introduction
The design of the PRO-12 is now regarded as classic synthesizer style. Two oscillators with multiple waveforms (which may be played independently or simultaneously) constitute the main sound source. The oscillators are mixed with white noise in the mixer section, then routed through the 24dB lowpass reso¬nating filter and amplifier section.
The filter and amplifier each have their own dedicated envelope curve with attack, decay, sustain and release controls. The filter envelope, oscillator B and the LFO (low frequency oscillator) can also be routed to different modulation destinations. One of the major highlights of the PRO-12 is that many interesting combinations of modulation source and destination can be accessed using the mod wheel and the 'poly mod' section. We have added some contemporary features which the original synth lacked: a full effects section comprising chorus, flanging and delay, keyboard aftertouch and MIDI clock synchronisation. In addition, the PRO-12 now has
12 voices - when played in 'unison mode', this produces amazing results.
4
Getting started
Making Connections
Connecting the power adaptor
To connect your Klangbox to a mains supply, please use the power adaptor supplied with the unit. First connect the power adaptor to your Klangbox. Before plugging the adaptor's plug into a mains socket, make sure it is compatible with the mains voltage in your country. If you lose the power supply, a standard AC or DC 12V / 1.5A power adaptor can be used as a replacement. The Klangbox power socket requires a hollow plug (5.5 mm x 2.1mm x 11.5 mm, centre positive).
MIDI connections
There are two ways to play your Klangbox using MIDI:
1. Connect your Klangbox directly to a master keyboard.
2. Connect your Klangbox to your computer's MIDI port in order to use it with a sequencer or with the Klangbox
Remote Software.
Connect the MIDI in and out of your Klangbox to the MIDI in and out of your keyboard or computer. The MIDI input of your Klangbox should be connected to the MIDI output of your keyboard / computer, and vice versa.
The Klangbox incoming MIDI signal can also control another instrument if you connect the Klangbox 'MIDI thru' to the instrument's MIDI in. If your computer does not have a
MIDI port, you can use USB connection as an alternative.
The yellow MIDI LED displays detected MIDI messages that are coming in at MIDI In with the adjusted MIDI channel.
5
Audio Connections
In order to hear the Klangbox, connect its stereo outputs to the left / right inputs of a mixer, a computer sound card or a HiFi system. You can also process external signals by plugging an audio sound source into your Klangbox input.
Power Switch
This is rather obvious, but in order to activate the Klangbox please turn the power switch on!
The blue LED is the displaying the power status and the yellow LED is detecting MIDI.
USB Connections and driver installation (Windows XP)
An alternative to using MIDI to connect your Klangbox to a computer is to use the built-in USB interface. On a PC, this requires Windows
XP with Service Pack 2; the Mac version supports OS10.4. After connecting the Klangbox to a computer, Windows will automatically recognize the Klangbox as an audio
USB instrument. No extra drivers are required - you can start playing right away! After starting your sequencer program (shown here:
Cubase SX), you can use the USB audio instrument driver as a MIDI port. Once in a while, under older versions of Windows XP (before Service Pack 2), the USB port will not re-appear on screen after disconnecting the Klangbox. In this case, please reboot Windows XP. After rebooting, your USB port should appear again.
Installation of the Remote Software
To install the Remote Software supplied with the Klangbox on your
PC, please put the CD-ROM labelled 'Klangbox into the CD-R drive of your computer find and doubleclick “Pro-12 Klangbox 3.3K.exe” in the Pro-12 folder.
6
You will then see the message 'Welcome to the Installation' - please continue by pressing 'Next'.
On the following page you will find the license agreement. Please read it carefully and if you agree, select "I accept the license terms"
- then continue by pressing the 'Next' button. You can now set the installation path within the 'Installation path' drop-down menu. If you don’t set a dedicated path here, the Remote
Software will be installed to e.g.
“C:\Programs\Creamware\Pro-12 3.3K”.
Installation requires 8 MB of empty hard disk space.
The 'Choose Start Menu Folder' lets you choose your own directory. If you don't make a choice, a directory will be created.
Presets
The selected preset number of your internal Klangbox preset can easy changed from an external keyboard or MIDI software via
MIDI Bank select and MIDI Program Change. Bank 0 provides the first bank which is named “Factory Bank” and Bank 1 is addressing the second internal bank, which is named “User Bank”.
Once a bank is selected presets can be selected with Programm
Change only. Default is the Factory Bank.
7
Remote Software
General
To control your Klangbox with the Remote Software, you have to connect the Klangbox to a computer via USB or MIDI.
Panel Layout
The Remote Software has three pages for sound control: the 'Main' page, the 'Add' page contains additional parameters as aftertouch and modulation wheel settings. Control settings for the chorus, flanger and delay effects are found on the 'Effects' page.
An additional 'Prefs' page contains the Remote Software's system settings and also a facility to update your Klangbox operating system when updates become available.
On the Remote Software's lower panel you will find the preset administration section, an integrated virtual MIDI keyboard and also a
MIDI monitor which enables you to view incoming MIDI messages.
8
MAIN Page
Oscillator A&B
Apart from a few small differences, oscillators A & B are largely identical.
Both have sawtooth and pulse waveforms, and oscillator B has an additional triangle wave. Each oscillator waveform has its own dedicated on/off button and all of them can be active at the same time, which allows a mix of up to five waveforms in parallel. The pulse wave has a variable width which can be adjusted manually or via modulation - full width produces a fat 'square wave' sound, while more narrow settings create a thinner, more nasal tone. In addition, oscillator B can operate in a lower frequency band which allows you to use it as a typical LFO (low frequency oscillator). If oscillator B is used as a modulation source, you can disable its keyboard tracking to make it produce a fixed pitch. The pitch of oscillator A can be synchronized with oscillator B, which creates some interesting timbres.
Frequency (both oscillators)
Each oscillator has a basic frequency (tuning / pitch) control which operates in semitone steps over a five-octave range.
Fine (oscillator B)
Oscillator B has its own fine tuning knob with a range of one semitone. Detuning oscillator B slightly and mixing it with oscillator A produces a characteristic 'beating' effect - this instantly recognisable analogue synthesizer sound helps make their sound rich and vibrant.
Sawtooth wave button (both oscillators)
Switches the oscillators' sawtooth wave on and off.
9
Coarse
Use this to set the oscillator frequency. The range can be adjusted over 6 octaves.
Fine
Use this knob to detune the oscillators with respect to one another.
Detuning and then mixing two oscillators produces vibrations that result in a more lively sound. The range can be adjusted over approximately one octave.
Octave Up/Down
Unlike the original model, our remake is equipped with a switch that allows you to set each oscillators’ frequency in octave steps over a range of 3 octaves.
Keyboard On/Off
You can use this switch to disconnect Oscillator 1 from the keyboard in order to use it as an LFO. The oscillator is now running at a much slower rate. Instead of frequencies spanning several octaves in the higher ranges, the “coarse” setting now ranges from just
0.2 Hz to 20 Hz.
Sync On/Off
This setting activates the hard sync from Oscillator 2 to Oscillator 1.
Hard sync makes the Oscillator 2 waveform re-start with each cycle of the Oscillator 1 waveform. This process transfers the pitch from
Oscillator 1 to Oscillator 2. Depending on the “coarse” setting and
Oscillator 2’s frequency modulation, you can create different overtone spectra each time you re-start the waveform.
Audio mixer
The audio mixer is used to mix the oscillators' signal before they are routed to the filter section. Each oscillator has its own volume control.
A third knob controls the amount of unpitched 'white noise' (useful for creating percussion sounds and other effects) in the mix.
10
Filter section
Along with the envelope curve and other modulation sources, the PRO-12 ASB's filter controls the way the synthesizer's tone changes over time. The filter is the
'lowpass' type with a slope of 24dB per octave; this means that all frequencies above the 'cutoff' frequency are reduced in volume by 24dB per octave, while frequencies below the cutoff point are left untouched. Filter 'resonance' is created by feedback between the filter's input and output, which accentuates frequencies around the region of the cutoff frequency. When the resonance is turned right up, the filter self-oscillates (i.e. produces a musical pitch).
To modulate the filter cutoff you can use the filter's envelope curve, keyboard tracking, the LFO and the two sources in the 'Poly Mod' modulation matrix (see below).
Cutoff
FiIlter 'cutoff frequency' is the frequency above which the PRO-12
ASB's tonal spectrum is filtered and its overtones are reduced in volume. You can adjust the cutoff frequency manually.
Resonance
This knob determines the amount of resonance in the filter's sound.
Filter resonance is created by feedback between the filter's input and output, which accentuates frequencies around the region of the cutoff frequency. When resonance is turned right up the filter selfoscillates, producing a sine wave at the selected cutoff frequency.
The filter can therefore be regarded as an additional sound source
11
Envelope Amount:
This controls the intensity of the filter's envelope curve. When the knob is turned up the filter envelope curve acts on the filter cutoff, causing its frequency to change over time and producing a mobile timbre. The cutoff frequency returns to normal at the end point of the envelope curve.
Keyboard Amount:
This determines the strength of the filter cutoff's 'keyboard tracking'.
When the knob is turned up, the cutoff frequency increases in value in response to higher notes, producing a brighter and more 'open' tone in the upper keyboard range.
This determines the strength of the filter cutoff's 'keyboard tracking'.
When the knob is turned up, the cutoff frequency increases in value in response to higher notes, producing a brighter and more 'open' tone in the upper keyboard range.
12
Amplifier
The amplifier's ADSR (attack / decay / sustain / release) envelope curve determines how the volume of a sound changes over time.
The PRO-12 master volume control is part of the amplifier section.
Attack
Determines the duration of the initial 'attack' phase of the ADSR envelope curve. In this phase, the volume rises to maximum in the time set by the attack control.
Decay
This determines the duration of the second phase of the ADSR envelope curve. During the 'decay' phase the envelope curve falls to the value set under 'sustain'.
Sustain
'Sustain' sets the volume at which the envelope curve comes to rest once the decay phase is over.
Release
The 'release' controls the duration of the dieaway of the sound after a key is released. (N.B. this dieaway is only introduced when the
'release' switch is turned on.) During the release phase of the ADSR envelope the envelope curve falls back to minimum.
Velocity
Velocity control is a new feature not implemented on the original
1978 synthesizer. The PRO-12's volume and tone can now respond dynamically to subtle variations of keyboard touch - the amplifier velocity control affects overall volume, while the filter velocity control affects the instrument's tone colour. Higher velocity settings produce greater variations of dynamic response.
13
Options for Amp- and Filter Envelope
ADR
Pressing this button automatically sets the sustain to zero. This is a good way to switch rapidly between a sustaining and a percussive sound without having to change the sustain level each time. ('ADR' is another feature not available on the original 1978 synth.)
Release
This button determines whether 'release' is on or off.
When release is switched on, notes die away after releasing the key at a rate set by the amplifier release control.
Volume
This controls the master volume of the synthesizer. It also sets the volume of the signal routed to the effects section, so you can use it to keep effects at a workable level, avoid distortion when using the flanger effect with lots of feedback, etc.
14
LFO
The LFO (low frequency oscillator) of your PRO-12 features the same three waveforms used by oscillator B - sawtooth, triangle and pulse. Choose a waveform simply by pushing one of the three LED push buttons; you can turn them on individually, all at the same time or in any combination you like, which can lead to very interesting results. The destinations of the LFO modulation are set in the 'wheel mod' section.
The 'Add page' of the Remote Software provides new LFO features not found on the original synthesizer. On the 'Add page' you can sync the LFO to external MIDI clock, and also set the LFO so that it restarts every time a key is played.
LFO Frequency
This controls the frequency (speed) of the LFO - higher frequencies produce faster modulation.
LFO Saw wave
Switches the LFO saw wave on and off.
LFO Triangle wave
Switches the LFO triangle wave on and off.
LFO Pulse wave
Switches the LFO pulse wave on and off.
15
Modulation Overview
The PRO-12 has three modulation sources: LFO, filter envelope and oscillator B. These can be individually or simultaneously routed to five different destinations - oscillator A frequency, oscillator A pulse width, oscillator B frequency, oscillator B pulse width and filter cutoff.
The LFO has its own dedicated modulation buss which is controlled by the mod wheel - the LFO modulation destinations are selected in the 'Wheel Mod' section. The 'Poly Mod' section has controls for routing the filter envelope and oscillator B modulation sources to any or all of the five destinations - the modulation intensity is adjusted manually for each source. When 'Poly Mod' is in use, pushing up the modulation wheel adds to the overall modulation depth. The filter envelope and oscillator B are polyphonic modulation sources, which means that they act upon individual synthesizer voices; the
LFO is a monophonic source which modulates all voices globally.
Wheel Mod
The modulation wheel controls the intensity of the 'wheel buss' LFO modulation. In the origi¬nal synthesizer, this was the only way to control the wheel buss, but the PRO-12 has more advanced options, including additional controls for overall modulation intensity and modulation offset. (Pitch bend range can also be programmed now - you will find these controls on the 'Add page' of the Remote
Software.)
LFO / Noise source mix
This control allows you to blend noise in with the LFO modulation higher settings introduce more noise!
16
Poly Mod
In this section you can set the depth (intensity) of the modulation sources (filter envelope and oscillator B) and select single or multiple modulation destinations.
Source Amount
Filter Env
This knob sets the modulation strength of the filter envelope for all selected destinations.
Osc B
This knob sets the modulation strength of oscillator B for all selected destinations.
Destination (Poly Mod / LFO)
Freq A
Selects oscillator A's frequency (pitch) as a modulation destination.
Freq B
Selects oscillator B's frequency (pitch) as a modulation destination.
PW A
Selects oscillator A's pulse width as a modulation destination.
PW B
Selects oscillator B's pulse width as a modulation destination.
Filter
Selects the filter cutoff as a modulation destination.
17
Glide
The 'glide' effect creates fluent sliding pitches (glissandi) between notes at a speed determined by the glide control.
This knob sets the rate of the pitch glides - higher settings produce slower glides. The glide function doesn‘t have a separate on-off switch, but is activated simply by turning up this control. If the glide control is set to zero position, no glides will be heard!
Unison
Pressing this button makes the PRO-12 operate in 'unison mode', in which a single note triggers multiple voices sounding in unison this creates a very big, powerful sound. More unison parameters can be accessed on the 'Add page' of the Remote Software.
18
ADD Page
Additional Features
Bend Range
This is where you set the maximum detuning via pitch bend in half tones. The value range covers 0 to 24 semitones.
Modulation Intensity
The maximum intensity of the engageable oscillation and filter modulations that can be set via the modulation wheel.
Keyboard Mode
Retrig/Normal
This control toggles between the two trigger modes of the envelope curve. In 'normal' mode, the envelope curve is retriggered only when a detached fingering style is used: this means that when using a legato playing technique, only the initial note will have an attack. In 'retrigger' mode the envelope curve restarts on every note regardless of playing style, so sounds keep their attack even when played legato.
This is useful when a consistently percussive attack is required.
Low Note/Last Note
This switch toggles between 'low note' and 'last note' priority. With
'low note priority', lower notes take priority over higher notes, which means that a high note will not sound if a low note is being held. If
'last note priority' is selected, the last note played always sounds no matter what other notes are being sustained. Along with the envelope trigger modes on the 'Add page', this opens up some interesting musical possibilities! (The difference between the two settings is most noticeable in 'single' and 'unison' modes.)
Single
If you select 'single' the instrument uses only one voice. It's advisable to use single mode when playing solo sounds with glide.
19
Aftertouch
The original 1978 synthesizer did not have aftertouch facilities, so the PRO-12 aftertouch function has been modelled on that of the later Prophet™ T8. However, unlike the T8, the PRO-12 aftertouch works globally (this is called 'channel aftertouch') rather than polyphonically ('key aftertouch'). This means that when aftertouch is introduced on one note, the resulting modulation will affect all the other notes currently being played.
Pitch
The degree to which aftertouch affects both oscilllators' pitch can be adjusted here. This facility allows you to use aftertouch to create pitch bends.
Freq A
Selects oscillator A's frequency (pitch) as an aftertouch modulation destination.
Freq B
Selects oscillator B's frequency (pitch) as an aftertouch modulation destination.
PW
Controls the amount of aftertouch applied to both oscillators' pulse width.
PW A
Selects oscillator A's pulse width as an aftertouch modulation destination.
PW B
Selects oscillator B's pulse width as an aftertouch modulation destination.
20
Filter
Controls the amount of aftertouch applied to the filter cutoff - this allows aftertouch to be used to create filter sweeps.
Amp
Controls the amount of aftertouch applied to output volume.
MW Amt
Controls the amount of aftertouch applied to the 'wheel buss' (LFO) modulation.
LFO Freq
Controls the amount of aftertouch applied to the LFO's frequency
(speed).
Time Velocity
These settings allow the envelope curve times to be modulated via velocity.
Filter Envelope
Attack
Controls the amount of velocity modulation applied to the filter envelope attack time.
Dec / Rel
Controls the amount of velocity modulation applied to the filter envelope decay and release times.
Amplifier Envelope
Attack
Controls the amount of velocity modulation applied to the amplifier envelope attack time.
Dec / Rel
Controls the amount of velocity modulation applied to the amplifier envelope decay and release times.
21
MIDI Clock
BPM
This knob controls the tempo of the the PRO-12 internal MIDI clock in BPM.
LFO Settings
Retrig
This control toggles between the the LFO's two modes. In 'free run' mode, the LFO cycles freely and independently; in 'retrigger' mode the LFO is restarted / retriggered whenever a note is played.
Phase
This control sets the phase of the LFO from 0 to 180 degrees.
MIDI
Use this switch to select whether the frequency (speed) of the LFO is set manually (via its front panel 'frequency' control) or via MIDI clock. If 'MIDI' is selected, the LFO uses the note length set in 'BPM
L' on the Effects page (see below). The combination of MIDI clock tempo and note length will control the speed of the LFO.
22
Wheel MOD
MW Intensity
This sets the maximum intensity the 'wheel buss' modulation can reach when the modulation wheel is pushed all the way up.
MW Offset
You can use this control to add built-in modulation to a patch, which saves having to push up the modulation wheel every time!
If a patch uses the MW offset, you can still use the mod wheel
to add more modulation.
Bend Range
This knob sets the instrument's pitch bend range in semitone steps from 0 to 24 semitones (two octaves).
Unison
Voices
Determines how many voices sound simultaneously when one note is played in unison mode.
Detune Controls the amount of detuning between the unison voices.
23
EFFECTS (Chorus/Delay)
The 'Add' page contains also controls for the chorus / flanger and stereo delay effects built into your Klangbox.
Chorus / Flanger
Flanger
This switch toggles between the chorus and flanger effects.
Rate
Controls the speed of the chorus / flanger modulation.
Depth
Sets the intensity of the modulation.
Phase
Sets the phase of the modulation from 0 to 180 degrees.
Feedback
Controls the amount of feedback (regeneration).
Dry / Wet
This controls the mix balance between the dry and effected signals
- a maximum setting gives 100% chorused / flanged sound with no dry signal.
Delay Left / Right
This section contains separate controls for the left and right channels of the Klangbox stereo delay effect.
BPM L
Click on this button to set the left channel delay to a musical note length - if you click on the arrow to the right of the 'note' window, a drop-down menu appears with values ranging from whole notes (1/
1) down to 64th note triplets (1/64T). (N.B. when the LFO is set to
'MIDI' on the 'Add page', the note length selected here will affect the
LFO speed.)
24
BPM R
Click here to set the right channel delay to a musical note length.
Cross
Controls the amount of left channel delay feedback signal sent to the right channel.
Time (left / right)
Adjusts the time of the delay from 1 to 1365 milliseconds (= 1.365
seconds). If 'BPM' is selected, you can enter the value as a note length.
Feedback (left / right)
Controls the amount of feedback applied to the delay effect. (This affects the number of repeats you will hear.)
Hi Damp (left / right)
Controls the amount of 'treble damping' applied to the delay. (This simulates the effect of old tape echo devices, whose repeats used to grow successively duller on each reiteration!)
Level (left / right)
Controls the delay volume level.
Dry / Wet
As with the chorus / flanger effects, this controls the mix between the dry and effected signals - a maximum setting gives a delay-only sound with no dry signal mixed in.
25
PREFS PAGE
The 'Prefs' page is used to edit the Klangbox system settings.
MIDI In / Out
Device (in / out)
Use these windows to select the MIDI device (and port) you use for connecting the Klangbox MIDI in and out to your computer.
Hardware Info
In this section you will find details of your Klangbox hardware version (e.g.
Prodyssey 1.05), which you may need when downloading firmware updates.
Device
Displays the name of your unit.
Version
Shows the version number of your Klangbox firmware.
Serial Number
Displays the serial number of your Klangbox.
Refresh
Click on this button to update the displayed information for the unit, while reconnecting the software with the Klangbox again.
26
Firmware Update
This facility enables you to download software updates for your
Klangbox operating system when they become available.
Activation Key
Enter the activation key code of your Klangbox here.
DSP Software
Displays the current DSP software, which is responsable for the sound of your Klangbox.
Firmware Source File
Displays the name of the update file to be downloaded.
Browse
Click on the 'Browse...' button to select the directory where the update file will be saved.
Write
Click on the 'write' button to install the update on your Klangbox.
Global
Channel
By defining the channel you can change the MIDI channel of the hardware MIDI input of your Klangbox and also the MIDI channels of remote software. When connected via USB the Klangbox receives in Omni mode.
27
Bank
There are two internal preset banks in Klangbox and each contains 128 presets. The first bank is named „Factory Bank“ (F) and the second „User
Bank“ (U). They can also be addressed via MIDI bank select.
Preset
By clicking on the arrow keys you can step through the internal presets of the selected preset bank.
EFX Bypass
Pressing the 'bypass' button turns all effects off.
(Depending on your effects settings, this might make some presets sound a little louder.) Once selected, the 'bypass' LED will light and all effects will be muted - pressing the button again cancels the
'bypass' and turns the effects back on.
MIDI MONITOR
The 'MIDI monitor' button is on the lower panel of the Remote
Software's display. Click on it to view a list of incoming and outgoing
MIDI messages.
Clear
Removes all entries from the MIDI monitor's display list.
28
MIDI KEYBOARD
The Remote Software's built-in MIDI keyboard enables you to play the Klangbox without using an external keyboard or sequencer software - you can play the synthesizer with the computer mouse.
Turn on the MIDI keyboard by clicking on its switch of the Remote
Software's display.
Octave
Sets the range of the MIDI keyboard in octave steps.
29
PRESET ADMINISTRATION
The Remote Software always displays the currently active preset's name at the top right of its panel. Use the forward / back arrows to the left of the preset name to step through the presets. When it comes to more advanced preset management, the Remote
Software's integrated preset administration section is an easy and convenient way of storing, exchanging and editing your presets.
Preset Window
Click on 'Preset' (on the lower part of the Remote Software's front panel) to open the preset window and view lists of presets.
Open / Save File
When you click on the 'preset' button in the top left corner of the preset window, a drop-down file menu appears. Select 'open file' to open an existing preset file (which can contain multiple banks of presets) from your computer's hard drive. You can save preset files to create back-up copies, or to exchange with other Klangbox users.
The extension for preset files is *.pdy.
The Preset Bank
To save a preset to your computer hard drive, you first have to create a bank. If no bank exists or you want to create additional banks, select 'create bank' from the drop-down menu. Presets may be dragged and dropped from one bank to another. (To change the name of an existing bank, click and hold on its name, enter the new name and press 'enter' - the new bank name is now stored.) Use
'new file', 'open file', 'save file' and 'save file as' to manage your banks of presets.
30
Storing, deletion and changing of Presets
To store a single preset in a bank, please create a new entry by selecting 'create preset' from the dropdown menu. The preset will be added to the bottom of the preset list with the name 'New Preset' - right click on the name to rename it. (You can also give it a number and rating, define its category and add a comment.) After creating a new entry, store the edited preset bank by clicking on 'save' or 'save as'.
Right click on a preset name to select further options, 'restore', 'overwrite' and 'delete' (use 'restore' to load an existing preset).
Upload of Preset files
To transfer presets between the Klangbox hardware and the Remote Software, click on the 'Box' button. You will see four options in a drop-down menu:
1. Upload user bank to box
Ports user bank data from the Remote Software to the Klangbox unit.
2. Upload factory bank to box
Ports factory bank data from the Remote Software to the Klangbox unit.
3. Download user bank from box
Ports Klangbox user bank data to the Remote Software.
4. Download factory bank from box
Ports Klangbox factory bank data to the Remote Software.
31
C C
0
1
2
P a r a m e t e r
B a n k S e l e c t
M o d u l a t i o n
U n i s o n v o i c e s
C C
6 4
6 5
6 6
P a r a m e t e r
S u s t a i n P e d a l
S o s t e n u t o
4 9
5 0
5 1
5 2
5 3
5 4
5 5
5 6
5 7
5 8
5 9
6 0
6 1
6 2
6 3
4 1
4 2
4 3
4 4
4 5
4 6
4 7
4 8
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
7
8
9
1 0
5
6
3
4
U n i s o n D e t u n e
G l i d e T i m e
D a t a E n t r y
D e v i c e V o l u m e
L F O S e t t i n g s R e t r i g
L F O S e t t i n g s P h a s e
V o l u m e
O s c A F r e q u e n c y
O s c A S h a p e S a w
O s c A S h a p e P u l s e
O s c A P u l s e W i d t h
O s c A S y n c
O s c B F r e q u e n c y
O s c B F i n e
O s c B S h a p e S a w
O s c B S h a p e T r i a n g l e
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
M a s t e r T u n e
O s c B S h a p e P u l s e
A f t e r t o u c h P i t c h
B e n d R a n g e
O s c A V o l u m e
O s c B V o l u m e
O s c B P u l s e W i d t h
O s c B L o F r e q
O s c B K e y b o a r d
3 0 A f t e r t o u c h D e s t F r e q A
3 1 A f t e r t o u c h D e s t F r e q B
3 2
3 3
B a n k S e l e c t
N o i s e V o l u m e
3 4
3 5
3 6
3 7
3 8
3 9
4 0
A f t e r t o u c h P W
A f t e r t o u c h M W A m t
E x t e r n a l V o l u m e
A f t e r t o u c h D e s t P W A
A f t e r t o u c h D e s t P W B
K e y b o a r d A m o u n t
C u t o f f
9 4
9 5
9 6
9 7
9 8
9 9
1 0 0
1 0 1
1 0 2
1 0 3
1 0 4
8 5
8 6
8 7
8 8
8 9
9 0
9 1
9 2
9 3
7 5
7 6
7 7
7 8
7 9
8 0
8 1
8 2
8 3
8 4
6 7
6 8
6 9
7 0
7 1
7 2
7 3
7 4
R e s o n a n c e
E n v e l o p e A m o u n t
F i l t e r E n v A t t a c k
F i l t e r E n v D e c a y
F i l t e r E n v S u s t a i n
F i l t e r E n v V e l o c i t y
F i l t e r R e l e a s e
A f t e r t o u c h L F O F e q
R e l e a s e
A f t e r t o u c h F i l t e r
A f t e r t o u c h A m p
A m p E n v A t t a c k
A m p E n v D e c a y
A m p E n v S u s t a i n
A m p E n v V e l o c i t y
M W I n t e n s i t y
M W O f f s e t
P o l y M o d O S C B
A D R
K e y b M o d e R e t r i g
L o w N o t e
A m p E n v R e l e a s e
P o l y M o d F i l t e r E n v
S o f t P e d a l
S i n g l e M o d e
U n i s o n
D r y / W e t
R a t e
P h a s e
D e p t h
F e e d b a c k
P o l y M o d D e s t i n a t i o n F r e q A
P o l y M o d D e s t i n a t i o n F r e q B
P o l y M o d D e s t i n a t i o n P W A
P o l y M o d D e s t i n a t i o n P W B
P o l y M o d D e s t i n a t i o n F i l t e r
D r y / W e t
T i m e L e f t
N o t e L e f t
F e e d b a c k L e f t
D a m p L e f t
L e v e l L e f t
B P M L e f t
L F O S h a p e S a w
L F O S h a p e T r i a n g l e
L F O S h a p e P u l s e
C r o s s
T i m e R i g h t
N o t e R i g h t
F e e d b a c k R i g h t
D a m p R i g h t
L e v e l R i g h t
B P M R i g h t
L F O F r e q u e n c y
B y p a s s
P r o g r a m
C h o r u s / F l a n g e r
W h e e l M o d F r e q A
W h e e l M o d F r e q B
W h e e l M o d P W A
1 0 5
1 0 6
1 0 7
1 0 8
1 0 9
1 1 0
1 1 1
1 1 2
W h e e l M o d P W B
W h e e l M o d F i l t e r
B P M
W h e e l M o d S o u r c e M i x
E x t e r n a l S o u r c e
L F O S e t t i n g s M I D I
1 1 3 T i m e V e l o c i t y A t t a c k F i l t e r E n v
1 1 4 T i m e V e l o c i t y D e c / R e l F i l t e r E n v
1 1 5
1 1 6 T i m e V e l o c i t y D e c / R e l A m p E n v
1 1 7
1 1 8
T i m e V e l o c i t y A t t a c k A m p E n v
1 1 9
1 2 0
1 2 1
1 2 2
A l l S o u n d s O f f
1 2 3
1 2 4
1 2 5
1 2 6
1 2 7
L o c a l C o n t r o l O f f
A l l N o t e s O f f
O m n i O f f
O m n i O n
M o n o O n
P o l y O n
32
Specifications
Technology
Number of Voices
Sampling Rate
Resolution
Analog Output
Analog Input
MIDI
USB
Power Supply
Dimensions (mm)
Weight
Physical Modelling,
Virtual Circuit Modelling
12
44.1 kHz (internal oversampling)
32 bit (Audio)
2 x 1/4 inch (6,3mm) unbalanced
2 x 1/4 inch (6,3mm) unbalanced
In, Out, Thru
Full Speed USB rev 1.1
AC or DC, 12V, 1.5 A
44,3 x 483,0 x 189,5 (1HE)
2,9 kg
Klangbox rear panel
33
Warranty Regulations
The hardware described within this documentation and the warranty regulations are governed by and granted according to German Law.
CreamWare Audio GmbH (“CreamWare”) warrants, that the described product has been free of failures within parts or components of the hardware and was found to be fully functional. Any single units has been checked by
Quality Assurance Department several times and with various measures, before this product has been delivered to you. Therefore please carefully read the following information, which are important in the case of probable damages or malfunctions:
If goods are being found defective, missing features described within the present documentation or becoming defective due to eventual fabrication deficiency or material defects within the first six months after purchase, then CreamWare shall at its sole discretion and evaluation replace or repair the defective parts or goods.
Multiple repairs shall be permissible. In case the malfunction or physical failure can not be fixed, customer receives the right to refrain from the purchase with refund of the amount originally paid for the defective product.
Within the time frame of 6 to 24 months customer has to provide proof, that the claimed malfunction or defective part or component has already been defective upon first delivery. In this case CreamWare will execute required repair or replacement at no cost upon acceptance of customer’s proof by CreamWare.
Any deficiencies caused by transportation have to be declared within a 14 days period after receipt of goods by written notice. Please note, that any warranty repair at no cost ruled by the above regulations requires registration of name and address either online at the “My Page” area on the CreamWare website (www.creamware.com) or by sending the proof of purchase together with the defective product.
To return defective goods, please contact the retailer where you purchased the product. As an alternative you can also contact CreamWare directly to receive the RMA number for the defective product. PLEASE NOTE: It is mandatory to return the product with the referring RMA number to avoid delays in repair. If possible, please also add a description of the failure occurred to enable us executing the repair as soon as possible.
Non-compliance with the operation and maintenance instructions, any alterations or modifications to the goods delivered, changing or utilizing any parts or materials not conforming to Sellers specifications will immediately render any warranties null and void. For a warranty claim, customer has to prove to CreamWare beyond a reasonable doubt that none of these aforesaid actions caused the goods to be defective or deficient.
CreamWare Audio GmbH
Fon ++49 2241 59 58 0
Fax email
++49 2241 59 58 57 [email protected]
The hardware described within this documentation is herewith certified to conform to the requirements set forth in the guidelines for electromagnetic acceptability (89/336/EWG)
CreamWare Audio GmbH, October 2006 sgn. Wolf Roth
34
Haftungsausschluss
Pro-12 Klangbox ist ein Produkt der CreamWare Audio GmbH in Siegburg.
(c) CreamWare 1998-2006 - alle Rechte vorbehalten.
Die nachfolgende Dokumentation wurde erstellt von CreamWare Audio GmbH (CreamWare), und beschreibt den jeweils aktuellen Stand der Produktentwicklung. CreamWare behält sich sich vor, gegebenenfalls
Änderungen an der Dokumentation vorzunehmen, sofern dies notwendig erscheint. Eine Verpflichtung zur
Veröffentlichung oder Benachrichtigung von Anwendern der vorliegenden Dokumentation besteht nicht.
Wir weisen ausdrücklich darauf hin, dass die vorliegende Dokumentation typographische Fehler oder technische Ungenauigkeiten enthalten kann.
CreamWare übernimmt keinerlei Gewähr, weder ausdrücklich noch implizit, für den Inhalt der vorliegenden
Dokumentation. Die Gewährleistung für das beschriebene Produkt ist in den Gewährleistungsbestimmungen eingehend beschrieben.
In keinem Fall haftet CreamWare für jegliche Form von Datenverlust oder Datenfehlern im Rahmen der
Nutzung des Produktes oder vorliegender Dokumentation. Insbesondere schließt CreamWare jegliche Haftung für Folgeschäden aus( wie z.B. verlorene Gewinne, entgangene Preisnachlässe, Produktionsausfälle sowie alle sonstigen Folgeschäden), welche sich aus der Nutzung des Produktes oder der Verwendung der vorliegenden Dokumentation ergeben.
In der vorliegenden Dokumentation etwaig verwendete Bezeichnungen von Marken- oder Produktnamen
Dritter unterliegen gesetzlichen Bestimmungen des Patent- und Markenrechts und sind das Eigentum der jeweiligen Rechteinhaber. Dies gilt auch dann, wenn im Text der entsprechende Hinweis nicht explizit angebracht ist. In keinem Fall gewährleistet CreamWare, dass die vorliegende Dokumentation und die hierin enthaltenen Informationen frei von Rechten Dritter sind.
Die vorliegende Dokumentation darf ohne vorherige schriftliche Einwilligung der CreamWare Audio GmbH weder in Teilen oder zur Gänze kopiert, übersetzt oder auf elektronische Medien übertragen werden.
Produkt und zugehörige Dokumentation unterliegen den AGB (Allgemeine Geschäftsbedingungen) der Cream-
Ware Audio GmbH zum jeweils aktuellen Stand.
35
Inhaltsverzeichnis
Benutzerhandbuch
Haftungsausschluss
Inhaltsverzeichnis
Einleitung
Erste Schritte
Anschluss des Netzteils
MIDI Verbindung
Audio Verbindung
Netzschalter
USB Verbindung und Treiberinstallation
Installation der Remote-Software
Presets
Die Remote-Software (Main Page)
Allgemeines
Oszillator A/B
Audio Mixer, Filter Sektion
Amplifier
LFO
Modulation
Glide, Unison
Remote-Software
Add Page
Effekte
Prefs Page
MIDI-Monitor
MIDI-Keyboard
Presetverwaltung
Spezifikationen
MIDI Implementationstabelle
Technische Daten
CE Konformitätserklärung
Gewährleistungsbestimmungen
Impressum
43
44
46
47
49
50
52
53
58
60
63
64
66
35
36
37
39
39
40
40
40
41
42
67
68
69
69
70
36
Willkommen
Vielen Dank, dass Sie sich für die PRO-12 Klangbox entschieden haben. Wir sind uns sicher, Sie werden mit Ihrem PRO-12 genau so viel Spaß haben, wie wir an der Entwicklung dieses einzigartigen und charakterstarken Synthesizers. Bitte lesen Sie diese Bedienungsanleitung aufmerksam durch, um alle Funktionen des PRO-
12 kennen zu lernen und nutzen zu können.
Einleitung
Wenn man von einem historischen polyphonen Analog-Synthesizer spricht, dann fällt jedem Kenner sofort ein Gerät ein, das 1978 von dem Amerikaner Dave Smith entwickelt wurde und als Blaupause für die weitere Entwicklung der polyphonen Synthesizer gelten sollte. Mit dem PRO-12 haben Sie nun die perfekte Emulation eines der "most sexiest" Synthesizer-Modelle vor sich. Der komplexe und dennoch logische Stimmenaufbau, die konsequent benutzerfreundliche Gestaltung des Bedienfeldes und der einzigartige Sound standen Pate für die zeitgemäße Version dieses polyphonen Synthesizer-Klassikers.
Als Soundquellen besitzt der PRO-12 zwei multifunktionale Oszillatoren, die mehrere Wellenformen - auch gleichzeitig! - zur Auswahl haben. Die Oszillatoren werden zusammen mit White Noise in der
Mixer-Sektion gemischt, danach kommen das 24dB Lowpass-Filter mit Resonanz und der Amplifier. Es gibt zwei Hüllkurven, beide haben Attack, Decay, Sustain und Release und sind dem Filter und
Amplifier zugeordnet. Die Filterhüllkurve, Oszillator B und das LFO können zu verschiedenen Modulationszielen geleitet werden.
37
Als Erweiterung zum Original wurde dem PRO-12 zusätzlich nocheine Effekt-Sektion mit Chorus/Flanger und Delay, MIDI Clock-Anbindung und Aftertouch spendiert.
Viel Spaß mit dem Pro-12 wünscht Ihnen Ihr
Creamware-Team!
38
Erste Schritte
Anschluss des Netzteils
Um die Klangbox mit Netzspannung zu versorgen, stecken Sie bitte das beiliegende Netzteil in die Steckdose. Verbinden Sie dann das
Netzteil mit der Netzbuchse Ihres Gerätes. Bitte achten Sie vor dem ersten Gebrauch auf die Kompatibilität des Netzteils zu Ihrem
Stromnetz. Bei Verlust des Netzteils kann ein Standard AC oder DC
12V Netzteil mit 1.5 A verwendet werden.
Der Anschluss des Netzteils an die Klangbox erfolgt über einen
Hohlstecker (5.5mm x 2.1mm x 11,5mm, centerpositiv).
MIDI Verbindung
Um die Klangbox über MIDI spielen zu können, stehen Ihnen zwei
Möglichkeiten zur Verfügung:
1. Das Gerät wird direkt an ein Masterkeyboard angeschlossen.
2. Das Gerät wird an den MIDI-Port Ihres Computers angeschlossen, um die Klangbox in Verbindung mit einem Sequencer und der
Remote-Software nutzen zu können.
Verbinden Sie hierzu die MIDI-Ein- und Ausgänge des mit den MIDI
Ein- und Ausgängen Ihres Keyboards bzw. Computers. Dabei muss der Eingang der Klangbox mit dem Ausgang Ihres Sequencer/
Keyboards verbunden werden. Mit der gelben MIDI LED können
Sie feststellen, ob am MIDI-Eingang anliegende Daten den in der Klangbox eingestellten MIDI-Kanal aufweisen. Daten die an den DSP gesendet werden erzeugen ein kurzes aufleuchten der LED.
39
Den Ausgang der Klangbox verbinden Sie bitte mit dem Eingang
Ihres Sequencers/Keyboards. Soll das eingehene MIDI-Signal noch an ein anderes Gerät weitergeleitet werden, so verbinden Sie bitte auch MIDI Thru. Steht Ihnen kein MIDI-Port zur Verfügung, so können Sie alternativ auch den USB-Port Ihres Computers verwenden.
Audio Verbindung
Um das Audiosignal der Klangbox abzuhören, verbinden Sie die Stereo Ausgänge mit den Audio-
Eingängen Ihres Mischpultes, Computers oder
Ihrer HiFi Anlage.
Um für die Klangerzeugung der Klangbox auch externe Signale nutzen zu können, verbinden Sie bitte auch den Audio-Eingang der
Klangbox mit einer beliebigen Klangquelle.
Netzschalter
Bitte schalten Sie den Netzschalter ein, um die
Klangbox in Betrieb zu nehmen. Die blaue Power-LED wird dann leuchten. Sie zeigt den
Betriebszustand an.
USB Verbindung und Treiberinstallation (Windows XP)
Um die Klangbox auch ohne MIDI-Interface in Verbindung mit einem Computer nutzen zu können, wurde ein USB-Anschluss integriert. Für diese Funktion wird eine Installation von Windows XP TM mit Service Pack 2 benötigt.
Nach dem Anschliessen an Ihren Computer wird Windows XP™
Ihrer Klangbox als USB-Audio-Gerät erkennen. Für dieses Gerät werden keine weiteren Treiber benötigt. Sie können also sofort mit dem Spielen loslegen!
Nach dem Starten Ihres Sequencers (wie z.B. Cubase SX™) steht
Ihnen der USB-Audiogerät Treiber als MIDI-Port zur Verfügung. In seltenen Fällen kann es passieren, dass eine ältere Version von
Windows XP™ (vor Service Pack 2) den USB Port nach dem Entfernen Ihres Gerätes nicht wieder frei gibt. In diesem Fall starten
Sie bitte WindowsXP™ neu. Nach dem Neustart steht Ihnen der
USB-Port wieder zur Verfügung.
40
Installation der Remote-Software
Um die Remote-Software zu installieren, legen Sie bitte die CD mit der Aufschrift Klangbox in das CD-Laufwerk Ihres Computers. Öffnen Sie den Ordner „Pro-12“ und starten sie bitte die Anwendung “Pro-12 Klangbox 3.3K.exe” manuell mittels Doppelklick von der CD.
Bestätigen Sie den angezeigten "Willkommen zur Installation" Dialog bitte mit "Next"
Im folgenden Dialog bestätigen Sie bitte die
Anerkenntnis der Lizenzbedingungen mit "I agree with the...", wählen Sie dann "Next".
Den Installationspfad der Remote-Software können Sie im Dialog "Directory" einstellen.
Standardmässig wird diese in das Verzeichnis z.B. "C:\Programme\CreamWare\Pro-12
3.3K" installiert, der hierfür erforderliche Speicherplatz beträgt etwa 6.0 MB.
Im "Startmenü-Ordner auswählen" haben Sie die
Möglichkeit, den Ordner für den Startmenü-Eintrag selbst zu bestimmen.
Im folgenden Dialog haben Sie noch einmal die Möglichkeit, die von Ihnen vorgenommenen Einstellungen zu überprüfen. Wählen
Sie "Start" um den Kopiervorgang zu starten.
Bestätigen Sie nun den „End“ Dialog durch
Klick auf den Button „Exit“.
41
Das Aufrufen der Presets
Die Nummer des gewählten internen Presets der Klangbox kann einfach über ein externes Keyboard oder eine ein angeschlossenes Programm mit MIDI Bank Select und MIDI
Program Change geändert werden.
Program Change Bank 0 selektiert die erste Bank (Factory Bank) udn Bank 1 adressiert die zweite interne Bank (User Bank). Wenn eine Bank selektiert ist, können Sie mit Program Change die einzelnen Presets ansteuern. Grundeinstellung ist die Factory
Bank.
42
Die Remote Software
Allgemeines
Um die Klangbox durch die Remote-Software steuern zu können, muss die Klangbox über USB oder MIDI mit dem Computer verbunden sein. Da beim ersten Start der notwendige MIDI-Treiber noch nicht eingestellt ist, kommt es zu Fehlermeldungen. Quittieren Sie diese mit „OK“ und stellen Sie auf der Prefs-Page den verwendeten Treiber und den MIDI-Kanal für Ein- und Ausgang ein.
Der USB-Treiber der Klangbox erscheint als USB Audiogerät. Klikken Sie nun auf Refresh, woraufhin die Seriennummer und die
Softwareversionen des Gerätes angezeigt werden. Durch das
Schließen der Software werden die Einstellungen gespeichert.
Aufbau der Oberfläche
In der Remote-Software stehen Ihnen 3 verschiedene Seiten zur
Verfügung. Die Main-Page mit den gerätetypischen Funktionen, die Add-Page mit zusätzlichen Effekten und erweiterten Einstellungen, sowie die Prefs-Page mit allen Informationen zu Systemeinstellungen. Desweiteren steht Ihnen zur Verfügung: der Preset-Dialog, MIDI-Monitor und ein MIDI-Keyboard.
43
MAIN Page
Die Oszillatoren A&B gleichen sich bis auf wenige Unterschiede. Per Schalter am jeweiligen Oszillator können verschiedene Wellenformen hinzugeschaltet werden. Bei Oszillator A sind dies die Wellenformen Sägezahn und Pulse, bei Oszillator B sind es Sägezahn, Triangle und Pulse. Die Wellenformen können gleichzeitig aktiv sein, wodurch eine Mischung von fünf Oszillatorwellenformen möglich ist. Die Pulsweite kann manuell oder per Modulation verändert werden. Falls Oszillator B als Modulationsquelle dient, lässt er sich von der Frequenzeingabe der Tastatur trennen, zusätzlich lässt er sich auf niedere Frequenzen skalieren wodurch er zum LFO wird.
Der Oszillator A kann zum Oszillator B synchronisiert werden.
Frequency
Benutzen Sie diesen Regler, um die beiden Oszillatoren gegeneinander zu verstimmen. Werden zwei Oszillatoren gegeneinander verstimmt und gemischt, entstehen Schwebungen, der Klang wird lebendiger.
Der Regelbereich erstreckt sich über eine Oktave.
Sawtooth On/Off
Schaltet die Sägezahnwelle des jeweiligen Oszillators ein bzw. aus.
Pulse On/Off
Schaltet die Pulswelle des jeweiligen Oszillators ein bzw. aus.
Triangle On/Off
Da Oszillator B auch als LFO verwendet werden kann, besitzt er zusätzlich eine Triangle-Welle. Hiermit schalten Sie die Wellenform ein bzw. aus.
44
Pulse Width
Stellen Sie hier die Pulsweite des Oszillators manuell ein. Um das
Ergebnis ihrer Einstellung zu hören, muss die Pulswellenform eingeschaltet sein. Der Regelbereich erstreckt sich von ca. 5% bis
100% der Pulsweite.
Ebenso besteht die Möglichkeit zur Pulsweitenmodulation, wobei dies im Abschnitt Modulation beschrieben ist.
Sync On/Off
Aktiviert den Hard Sync von Oszillator
A zu Oszillator B. Beim Hard Sync erfährt die Wellenform von Oszillator A mit jedem Periodendurchlauf von Oszillator B einen Neustart. Dadurch wird die Tonhöhe von Oszillator B auf Oszillator A übertragen. Je nach Octave- und Frequency-Einstellung bzw. Frequenzmodulation von Oszillator A können unterschiedliche
Effekte, die auf das Spektrum des Oszillators wirken, erzeugt werden.
Lofreq/Normal
Skaliert Oszillator B auf sehr niedrige Frequenzen herunter, der
Oszillator schwingt jetzt viel langsamer. Über die Modulationsmatrix lässt sich Oszillator B nun als zusätzliches LFO verwenden.
Keyboard Trennen Sie hiermit Oszillator B von der Tastatur. Der
Oszillator folgt nun nicht mehr der gespielten Note, sondern schwingt jetzt auf der durch Octave, Frequency und Lofreq gewählten Frequenz. So lässt er sich z.B. als Modulationsquelle mit einstellbarer
Frequenz verwenden.
45
Audio Mixer
Hier werden die Signale gemischt, bevor sie in das Filter eingespeist werden. Oszillator A und Oszillator B haben je einen eigenen Lautstärkeregler, ein weiterer Regler steuert die
Lautstärke des Noise Signals, bei dem es sich um weisses Rauschen handelt. Auf der Add-Page finden sie den Lautstärkeregler für ein externes Signal.
Filter Sektion
Die Filtersektion besteht aus einem modulierbaren Tiefpassfilter mit Resonanz, die bis hin zur Eigenresonanz reicht. Zusammen mit der
Hüllkurve und anderen Modulationen bestimmt das
Tiefpassfilter den Klangverlauf. Der Tiefpass hat eine
Flankensteilheit von 24dB/
Oktave. Frequenzen unterhalb der Cutoff Frequenz bleiben unbearbeitet, daher die Bezeichnung Tiefpass. Frequenzen oberhalb der Cutoff Frequenz werden abgesenkt mit 24dB/Oktave.
Resonanz entsteht durch Rückkopplung des Filterausgangs mit dem Filtereingang, die Frequenzen um die Cutoff
Frequenz werden verstärkt. Dank des Circuit Modelling
Verfahren besitzt das Filter die Eigenheiten des Originals, die
Cutoffeinstellungen und das Resonanzverhalten zeigen den typischen Charakter. Zur Modulation des Filters stehen eine eigene Hüllkurve, das Keyboard und die Quellen der Modulationsmatrix zur Verfügung.
Cutoff
Die Cutoff Frequenz ist die Frequenz, oberhalb der das Spektrum beschnitten wird - Obertöne werden abgesenkt. Verändern Sie hier die Cutoff Frequenz manuell.
46
Resonance
Hier stellen Sie die Resonanz-Parameter ein. Resonanz entsteht durch Rückkopplung des Filterausgangs mit dem Filtereingang, dabei werden die Frequenzen um die Cutoff Frequenz verstärkt.
Bei voller Resonanz schwingt das Filter in Eigenresonanz und erzeugt einen Sinuston mit der eingestellten Cutoff Frequenz. Das
Filter gilt deshalb auch als sechste Soundquelle.
Envelope Amount
Stellen Sie hier die Intensität der Hüllkurve ein. Der Cutoff folgt dem
Verlauf der Hüllkurve mit der eingestellten Intensität, ein Klangverlauf entsteht. Ausgangspunkt und Endpunkt des Hüllkurvenverlaufs ist die eingestellte Cutoff Frequenz.
Keyboard Amount
Durch Keyboard Amount folgt die Cutoff-Frequenz mit der eingestellten Intensität der gespielten Note. Ist der Regler auf Position „7
„der Skala, folgt die Frequenz zu 100%, d.h. pro Oktave verdoppelt sich die Cutoff-Frequenz.
Amplifier
Zusammen mit der Hüllkurve bestimmt der Amplifier den Lautstärke-Verlauf des Klangs. Zur Modulation des Amplifiers steht eine
ADSRHüllkurve zur Verfügung. Der Volume-Regler ist Teil dieser
Sektion.
Attack
Dauer des ersten Hüllkurvensegments. In der Attack-Phase wächst die Hüllkurve mit der eingestellten Zeit auf das Maximum an. Die
Stärke des Anstiegs wird durch Envelope Amount bestimmt. Das
Maximum wird durch Cutoff Frequency und Envelope Amount gemeinsam bestimmt.
47
Decay
Dauer des zweiten Hüllkurvensegments. In der Decay-Phase fällt die Hüllkurve mit der eingestellten Zeit auf den unter Sustain eingestellten Wert zurück.
Sustain
Wert, auf dem die Hüllkurve nach dem Decay verweilt.
Release In der Release-Phase fährt die Hüllkurve mit der eingestellten Zeit zurück auf ihr Minimum. Der Wert auf den sie fällt, ist vom Cutoff bestimmt.Die Zeit in der sie fällt, wird durch Decay bestimmt.
Velocity
Modulation aller Level der Hüllkurve per Anschlagsstärke. Je nach eingestellter
Modulationsstärke werden die Pegel der Hüllkurve zwischen Minimum und Maximum variiert. Die Anschlagsstärke nimmt dabei auch
Einfluss auf die Klangfarbe.
Optionen für Amp- und Filter Envelope
ADR
Aktivieren Sie diese Option, um das Sustain auf „0“ zu setzen. Sie können hierdurch schnell zwischen perkussiven und Sustain-basiertem Sound umschalten, ohne dabei den Sustain Level ändern zu müssen.
Release
Aktivieren Sie diese Option um die Release-Zeit auf
„0“ zu setzen.
Volume
Gesamtlautstärke des Synthesizers. Der Regler rechts neben der Filtersektion regelt die Lautstärke vor den Effekten, kann also auch zum Aussteuern der Effekte genutzt werden, um z.B. bei hohem Feedback des Flangers Verzerrungen zu vermeiden.
48
LFO (Low Frequency Oszillator)
Der LFO des PRO-12 bietet drei Wellenformen, welche die gleichen wie bei Oszillator B sind. Die Wahl der Wellenformen findet auch hier über drei Schalter statt. Es können alle drei Wellenformen, oder eine beliebige Kombination davon, gleichzeitig aktiv sein, was zu interessanten Ergebnissen führt. Die Wahl des Ziels und die
Intensität des LFOs werden in der Modulationsmatrix vorgenommen. Als Erweiterung zum Original finden Sie auf der Add-Page einige Zusatzparameter. Hier lässt sich z.B. das LFO zu einer
MIDI Clock synchronisieren oder auch der Neustart des LFOs per
Keyboard mit Startphase aktivieren
LFO Freq
Stellen Sie hier die Frequenz des LFOs ein.
Sawtooth On/Off
Schaltet die Sägezahnwelle ein bzw. aus.
Triangle On/Off
Schaltet die Triangle-Welle ein bzw. aus.
Pulse On/Off
Schaltet die Pulswelle ein bzw. aus.
49
Modulation
Der PRO-12 hat drei Modulationsquellen - Filter Envelope, Oszillator B und LFO - die mit bis zu fünf Zielen (Frequency Oszillator A,
Pulsweite Oszillator A, Frequency Oszillator B, Pulsweite Oszillator
B und Filter Cutoff) verknüpft werden können. Die Verknüpfung kann dabei direkt oder über das Modulationsrad erfolgen, man hat also zwei getrennte Modulationsbusse. Die Grundintensität der Modulation wird einmal pro Quelle eingestellt. Ist der Weg über das
Modulationsrad gewählt, so nimmt dieses zusätzlich Einfluss auf die Modulationstiefe. Die Filter Hüllkurve und Oszillator B sind polyphone Modulationsquellen, d.h. sie wirken pro Stimme. Der LFO ist
eine monophone Modulationsquelle, wirkt also nur einmal pro Klang.
Poly Mod
Stellen Sie in dieser Sektion die Intensitäten der Modulationsquellen Filter Envelope und Oszillator B ein und aktivieren Sie ein oder mehrere Modulationsziele.
Source Amount
Filter Env
Stellen Sie hier die Modulationstiefe der
Filterhüllkurve gemeinsam für alle ausgewählten
Ziele ein.
OSC B
Stellen Sie hier die Modulationstiefe von Oszillator B gemeinsam für alle gewählten Ziele ein.
50
LFO Amount
Stellen Sie hier die Modulationstiefe des LFO gemeinsam für alle gewählten Ziele ein.
Destination
Freq A
Aktivieren Sie diesen Schalter um das Modulationssignal zur Modulation der Frequenz des Oszillators A einzusetzen.
Freq B
Aktivieren Sie diesen Schalter um das Modulationssignal zur Modulation der Frequenz des Oszillators B einzusetzen.
PW A
Aktivieren Sie diesen Schalter um das Modulationssignal zur Modulation der Pulsweite des Oszillators A einzusetzen.
PW B
Aktivieren Sie diesen Schalter um das Modulationssignal zur Modulation der Pulsweite des Oszillators B einzusetzen.
Filter
Aktivieren Sie diesen Schalter um das Modulationssignal zur Modulation des Filters einzusetzen.
Wheel Modulation
Die Intensität des Wheel Busses in der Modulationssektion wird grundsätzlich durch das
Modulationsrad gesteuert. Im Original war dies sogar die einzige Möglichkeit der Steuerung dieses Busses. Zur besseren Kontrolle gibt es zusätzlich eine Modulation Intensity und einen
Modulation Offset. Die Intensität des Pitch
Bender ist ebenso einstellbar. Die Parameter befinden sich auf der Add-Page in der Remote-Software.
51
Glide
Durch Glide werden aufeinanderfolgende Noten von einem Ton in den nächsten mit der unter Rate eingestellten Zeit fliessend überführt. Glide Zeit, mit der aufeinanderfolgende Noten, von einem
Ton in den nächsten überführt werden. Glide muss nicht extra aktiviert werden. Es genügt wenn Sie eine Zeit einstellen, bei welcher der Glide-Effekt zum Tragen kommt. Stellen Sie die Zeit mit dem
Regler ein, um Glide zu aktivieren.
Unison
Aktivieren Sie hier den Unisono-Modus. Weitere Parameter können in der Remote-Software auf der Add-Page eingestellt werden.
52
ADD PAGE
Additional Features
Keyboard Mode
Retrig/Normal
Bestimmen Sie hier das Triggerverhalten der Hüllkurven. Im Modus Normal werden beim Stehlen von Stimmen die Hüllkurven nicht von neuem gestartet. Ein
Legatospiel, ohne das die Hüllkurve mit jeder Note getriggert wird, ist somit möglich. Im Modus Retrigger werden beim
Stehlen von Stimmen die Hüllkurven auf jeden Fall neu gestartet, perkussive Sounds behalten somit z.B. ihren Attack, selbst dann wenn sie legato gespielt werden.
Low Note/Last Note
Schaltet Low-Note-Priority oder Last-Note-Priority ein. Bei Low-Note-
Priority haben tiefe Töne gegenüber hohen Vorrang, eine hohe
Note kann keine tiefe Note klauen. Ist Last-Note eingeschaltet, wird immer die zuletzt gespielte Note wiedergegeben. Zusammen mit den Trigger-Modi auf der Main-Page ergeben sich interessante Einflussmöglichkeiten auf das Zusammenspiel von Stimmenklau und
Hüllkurvenstart.
53
Single On
Schaltet, egal wieviele Stimmen aktiv sind, die Stimmenverwaltung des Instruments auf eine Stimme. Die korrekte Wiedergabe von
Solo-Sounds mit Glide ist somit gewährleistet.
Aftertouch
Das Originalbesaß kein Aftertouch zur Modulationssteuerung. Die hier implementierte Aftertouch-Sektion biete ein Channel Aftertouch und keine Key Aftertouch. Mit anderen Worten, wird Aftertouch auf einer Taste gesendet, werden die entsprechenden Modulationen an alle gespielten Stimmen gesendet.
Pitch Osc A/B
Intensität und Richtung der Modulation auf die Tonhöhe der Oszillatoren. Sie können somit einen Pitchbend der Oszillatoren per Aftertouch steuern.
Freq A
Aktiviert die Modulation für Oszillator A.
Freq B
Aktiviert die Modulation für Oszillator B.
PW
Intensität und Richtung der Modulation auf die Pulsweite der Oszillatoren.
PW A
Aktiviert die Pulsweite für Oszillator A.
PW B
Aktiviert die Pulsweite für Oszillator B.
54
Filter
Intensität und Richtung der Modulation auf den Filter Cutoff.
Sie können somit Filtersweeps per
Aftertouch erzeugen.
Amp
Intensität und Richtung der Modulation auf die Lautstärke.
MW Amt
Intensität und Richtung der Modulation auf Modulationsrad.
LFO Freq
Intensität und Richtung der Modulation auf die LFO Frequenz.
Time Velocity
Diese Parameter finden sich nicht im Original.Sie können hier die
Hüllkurvenzeiten per Velocity modulieren.
Filter Envelope
Attack
Legen Sie hier Intensität und Richtung der Modulation der Attackzeit durch die Velocity fest.
Dec/Rel
Legen Sie hier Intensität und Richtung der Modulation der Decaybzw. Releasezeit durch die Velocity fest.
Amplifier Envelope
Attack
Legen Sie hier Intensität und Richtung der Modulation der Attackzeit durch die Velocity fest.
Dec/Rel
Legen Sie hier Intensität und Richtung der Modulation der Decaybzw. Releasezeit durch die Velocity fest.
55
MIDI Clock Settings
Nehmen Sie hier Einstellungen zum MIDI-Tempo vor und ob zur internen oder einer externen MIDI Clock synchronisiert werden soll.
External
Schaltet die MIDI Clock zwischen interner und externer
Synchronisation um.
Coarse/Fine
Zum Einstellen und Anzeigen des Tempos stehen zwei Textfelder zur Verfügung. Das erste Textfeld gibt Werte in BPM, das zweite in
1/100stel BPM an.
BPM
Stellen Sie hier das Tempo der internen Midi-
Clock in BPM ein.
LFO Settings
Retrig
Wählen Sie zwischen den Modi Retrig und Free Run. Im Modus
Free Run läuft der LFO frei, ohne Unterbrechung. Im Modus Restart wird der LFO durch Keyboard-Tastendruck auf der gewählten
Phase neu gestartet.
Phase
Bestimmen sie hier die Phase, mit der das LFO bei aktivem Retrig startet.
MIDI
Wählen sie hier ob die Frequenz des LFO manuell per Regler oder per MIDI und
Wahl einer Notenlänge gesetzt wird. Ist
MIDI aktiv, findet sich auf der Main-Page ein Drop-
Down-Menü mit einer Auswahl an Notenlängen. Die Länge der Note entspricht der Periode des LFOs.
56
Wheel MOD
MW Intensity
Maximale Intensität des Wheel-Busses in der Modulationssektion, die maximale Modulation wird dabei durch die Einstellung des Modulationsrades bestimmt.
MW Offset
Grundsätzliche Intensität des Wheel-Busses in der Modulationssektion. Das Modulationsrad kann, je nach eingestelltem Offset und eingestellter Intensität, die Modulation noch verstärken.
Bend Range
Stellen Sie hier die maximale Verstimmung durch Pitchbend in Halbtonschritten ein. Der Wertebereich beträgt 0 bis 24 Halbtöne.
Unisono
Voices
Legen Sie hier fest, wieviele Stimmen pro Tastendruck gleichzeitig erklingen sollen.
Detune
Legt die Verstimmung der Stimmen zueinander fest.
57
EFFECTS (Chorus/Delay)
Die Effect-Page beinhaltet
Bedienelemente für den eingebauten Chorus/Flanger und für den Delay-Effekt Ihrer Klangbox.
CHORUS/FLANGER
Chorus/Flanger
Wählen Sie hier zwischen Chorus und Flanger Algorithmus. Rate regelt den Wert Modulationsgeschwindigkeit.
Depth
Hier können Sie die Intensität der Modulation einstellen.
Phase
Stellen sie hier die Phase der Modulation ein.
Feedback
Regelt die Intensität der Rückkopplung ein.
Dry/Wet
Regelt den Effektanteil.
DELAY
Left Cannel regelt die Einstellungen des Delay Effektes im linken Kanal.
Right Channel regelt die Einstellungen des Delay Effektes im rechten Kanal.
Time
Stellen Sie hier die Zeit für das Delay ein. Ist BPM aktiv, so können sie den Wert in Notenlänge angeben, als Standard stellen Sie die
Zeit in Millisekunden ein.
58
Feedback regelt den Anteil an Rückkopplung im Delayweg. In der Praxis wirkt sich dieser Parameter auf die Anzahl an Echos aus.
Damp
Hier wird die Intensität der Höhendämpfung eingestellt.
Level
Level regelt die Lautstärke unabhängig für den linken und rechten
Kanal.
Tempo
Hier können Sie den Wert für das Delay-Tempo in BPM eingeben.
Dry/Wet
Regelt den Effektanteil.
59
PREFS PAGE
Hier ändern Sie Systemeinstellungen der Klangbox.
MIDI In/Out
Device
Wählen Sie hier den Ein- bzw. Ausgangsport, an dem Ihr ASB angeschlossen ist. Für diese Verbindung kann ein MIDI-Port Ihres Rechners, oder die USB-Verbindung verwendet werden.
Hardware Info
In dieser Sektion werden Informationen zu Ihrer Klangbox angezeigt.
Device
Name des angeschlossenen Gerätes
Version
Versionsnummer der Firmware der Hauptplatine.
Serial Number
Die Seriennummer Ihrer Klangbox.
Refresh
Aktualisiert die Anzeige bei neu angeschlossenem Gerät und stellt die Verbindung wieder her.
60
Firmware Update
Die Installation aktueller Firmware Ihrer Klangbox ist innerhalb der
Firmware-Sektion möglich.
Activation Key
Tragen Sie hier den Aktivierungsschlüssel Ihrer Klangbox ein. Sie erhalten Ihn, falls notwendig, von unserem Support.
DSP Software
Hier wird die Version der aktuell verwendeten klangerzeugenden
Software angezeigt.
Firmware Source File
Zeigt Ihnen die von Ihnen ausgewählte Update-Datei an.
Browse
Wählen Sie hier den Ort, an dem sich die Datei mit dem Update befindet.
Write
Mit "Write" installieren Sie das Update auf Ihre Klangbox.
61
Global
Channel
Stellen sie hier den MIDI Kanal der Ein- und Ausgänge von Remote Software und Klangbox ein.
Der hier eingestellte Kanal wird in der Klangbox gespeichert und als Kanal für die MIDI Anschlüsse verwendet. Über USB empfängt die Klangbox immer auf allen Kanälen (Omni Mode).
Bank
Es gibt zwei interne Preset-Bänke in der Klangbox, mit je 128 Presets. Die erste Bank heißt „Factory
Bank“ (F) und die zweite „User Bank“ (U). Mit MIDI
Bank Select können Sie diese Bänke ebenfalls direkt adressieren. Die Nummer des gewählten internen Presets der Klangbox kann einfach über ein externes Keyboard oder eine ein angeschlossenes Programm mit MIDI Bank Select und MIDI Program Change geändert werden.
Program Change Bank 0 selektiert die erste Bank (Factory Bank) und Bank 1 adressiert die zweite interne Bank (User Bank). Wenn eine Bank selektiert ist, können Sie mit Program Change die einzelnen Presets ansprechen. Grundeinstellung ist die Factory Bank.
Preset
Durch Klicken auf die Pfeiltasten können Sie die verschiedenen
Presets der gewählten Bank anwählen.
EFX Bypass
Betätigen Sie den Taster BYPASS, um den Effektweg zu umgehen.
Je nach Einstellung wird das Signal ohne Effekte etwas lauter als mit Effekten sein. Wenn die LED leuchtet, ist BYPASS aktiv, und die Effekte sind nicht hörbar. Ein erneutes Drücken des Tasters deaktiviert die Bypass-Funktion wieder.
62
MIDI MONITOR
Der MIDI-Monitor zeigt ein- und ausgehende MIDI-Nachrichten an.
Clear
Löscht die Anzeige des MIDI-Monitors.
63
MIDI KEYBOARD
Das MIDI-Keyboard ermöglicht es Ihnen, auch ohne Sequencer oder Keyboard Klänge der Klangbox mit der Maus zu spielen.
Sie erreichen MIDI-Keyboard und MIDI-Monitor über den entsprechenden Button der Remote Software.
Channel
Hier wird der MIDI-Kanal eingestellt, auf dem gesendet werden soll.
Octave stellt den spielbaren Notenbereich in Oktavschritten ein.
64
Presetverwaltung
Die Presetverwaltung der Remote-Software ermöglicht das Speichern, Austauschen und Editieren von eigenen Presets.
Open Presetlist
Öffnet die Presetliste.
Open File
Öffnet ein Preset-File. Sie können die Presetliste als Datei speichern, um sie mit anderen Usern auszutauschen oder um Sicherungskopien anzufertigen.
Der Erweiterung der Presetdatei ist z.B. *.PDY
(beim Prodyssey). Mit den Pfeilen neben dem Preset-Knopf können sie durch die Presets "steppen".
Das Erstellen von Bänken
Um ein Preset speichern zu können, wird eine Bank benötigt. Ist noch keine Bank vorhanden oder möchten Sie Ihre eigene Bank erstellen, so wählen Sie bitte aus dem Sprungmenu "Create Bank".
Möchten Sie den Namen der Bank ändern, so drücken Sie bitte bei ausgewählter Bank die Taste F2 Ihrer Computertastatur. Nach dem
Eingeben eines Presetnamens bestätigen Sie die Eingabe mit der
Entertaste.
Speichern, Löschen und Ändern von Presets
Um ein Preset zu speichern, erzeugen Sie bitte einen freien Presetplatz über den Sprungmenu Eintrag "Create". Ist ein Programmplatz angelegt, so können Sie das Preset mit dem Eintrag "Save" speichern oder bereits vorhandene Presets überschreiben. Mittels
Taste "Restore" können Sie ein gewähltes Preset erneut anwenden.
Mit den Funktionen "New File", "Open File", "Save File" und "Save
File As" können Sie die Datei der Presetliste bearbeiten.
Upload der Presetdaten
Um die Preset-Daten der Klangbox-Hardware. mit denen der Remote-Software austauschen zu können, haben Sie unter "Box" vier
Optionen:
65
Upload User Bank to Box
Überträgt Daten der User-Bank von der Remote-Software auf die
Klangbox.
Upload Factory Bank to Box
Überträgt Daten der Factory-Bank von der Remote-Software auf die Klangbox.
Upload Use Bank from Box
Überträgt die Daten der User-Bank von Ihrer Klangbox zur Remote-Software.
Upload Factory Bank from Box
Überträgt Daten der Factory-Bank von Ihrer Klangbox zur Remote-
Software.
66
C C
0
1
2
P a r a m e t e r
B a n k S e l e c t
M o d u l a t i o n
U n i s o n v o i c e s
C C
6 4
6 5
6 6
P a r a m e t e r
S u s t a i n P e d a l
S o s t e n u t o
4 9
5 0
5 1
5 2
5 3
5 4
5 5
5 6
5 7
5 8
5 9
6 0
6 1
6 2
6 3
4 1
4 2
4 3
4 4
4 5
4 6
4 7
4 8
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
7
8
9
1 0
5
6
3
4
U n i s o n D e t u n e
G l i d e T i m e
D a t a E n t r y
D e v i c e V o l u m e
L F O S e t t i n g s R e t r i g
L F O S e t t i n g s P h a s e
V o l u m e
O s c A F r e q u e n c y
O s c A S h a p e S a w
O s c A S h a p e P u l s e
O s c A P u l s e W i d t h
O s c A S y n c
O s c B F r e q u e n c y
O s c B F i n e
O s c B S h a p e S a w
O s c B S h a p e T r i a n g l e
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
M a s t e r T u n e
O s c B S h a p e P u l s e
A f t e r t o u c h P i t c h
B e n d R a n g e
O s c A V o l u m e
O s c B V o l u m e
O s c B P u l s e W i d t h
O s c B L o F r e q
O s c B K e y b o a r d
3 0 A f t e r t o u c h D e s t F r e q A
3 1 A f t e r t o u c h D e s t F r e q B
3 2
3 3
B a n k S e l e c t
N o i s e V o l u m e
3 4
3 5
3 6
3 7
3 8
3 9
4 0
A f t e r t o u c h P W
A f t e r t o u c h M W A m t
E x t e r n a l V o l u m e
A f t e r t o u c h D e s t P W A
A f t e r t o u c h D e s t P W B
K e y b o a r d A m o u n t
C u t o f f
9 4
9 5
9 6
9 7
9 8
9 9
1 0 0
1 0 1
1 0 2
1 0 3
1 0 4
8 5
8 6
8 7
8 8
8 9
9 0
9 1
9 2
9 3
7 5
7 6
7 7
7 8
7 9
8 0
8 1
8 2
8 3
8 4
6 7
6 8
6 9
7 0
7 1
7 2
7 3
7 4
R e s o n a n c e
E n v e l o p e A m o u n t
F i l t e r E n v A t t a c k
F i l t e r E n v D e c a y
F i l t e r E n v S u s t a i n
F i l t e r E n v V e l o c i t y
F i l t e r R e l e a s e
A f t e r t o u c h L F O F e q
R e l e a s e
A f t e r t o u c h F i l t e r
A f t e r t o u c h A m p
A m p E n v A t t a c k
A m p E n v D e c a y
A m p E n v S u s t a i n
A m p E n v V e l o c i t y
M W I n t e n s i t y
M W O f f s e t
P o l y M o d O S C B
A D R
K e y b M o d e R e t r i g
L o w N o t e
A m p E n v R e l e a s e
P o l y M o d F i l t e r E n v
S o f t P e d a l
S i n g l e M o d e
U n i s o n
D r y / W e t
R a t e
P h a s e
D e p t h
F e e d b a c k
P o l y M o d D e s t i n a t i o n F r e q A
P o l y M o d D e s t i n a t i o n F r e q B
P o l y M o d D e s t i n a t i o n P W A
P o l y M o d D e s t i n a t i o n P W B
P o l y M o d D e s t i n a t i o n F i l t e r
D r y / W e t
T i m e L e f t
N o t e L e f t
F e e d b a c k L e f t
D a m p L e f t
L e v e l L e f t
B P M L e f t
L F O S h a p e S a w
L F O S h a p e T r i a n g l e
L F O S h a p e P u l s e
C r o s s
T i m e R i g h t
N o t e R i g h t
F e e d b a c k R i g h t
D a m p R i g h t
L e v e l R i g h t
B P M R i g h t
L F O F r e q u e n c y
B y p a s s
P r o g r a m
C h o r u s / F l a n g e r
W h e e l M o d F r e q A
W h e e l M o d F r e q B
W h e e l M o d P W A
1 0 5
1 0 6
1 0 7
1 0 8
1 0 9
1 1 0
1 1 1
1 1 2
W h e e l M o d P W B
W h e e l M o d F i l t e r
B P M
W h e e l M o d S o u r c e M i x
E x t e r n a l S o u r c e
L F O S e t t i n g s M I D I
1 1 3 T i m e V e l o c i t y A t t a c k F i l t e r E n v
1 1 4 T i m e V e l o c i t y D e c / R e l F i l t e r E n v
1 1 5
1 1 6 T i m e V e l o c i t y D e c / R e l A m p E n v
1 1 7
1 1 8
T i m e V e l o c i t y A t t a c k A m p E n v
1 1 9
1 2 0
1 2 1
1 2 2
A l l S o u n d s O f f
1 2 3
1 2 4
1 2 5
1 2 6
1 2 7
L o c a l C o n t r o l O f f
A l l N o t e s O f f
O m n i O f f
O m n i O n
M o n o O n
P o l y O n
67
Technische Daten
Technologie
Stimmenanzahl
Sampling Rate
Auflösung
Analoger Eingang
Analoger Ausgang
MIDI
USB
Netzteil
Abmessungen (mm)
Weight
Physical Modelling,
Virtual Circuit Modelling
12 Stimmen
44.1 kHz (internes oversampling)
32 bit (Audio)
6,3mm Klinke, asymmetrisch
6,3mm Klinke, asymmetrisch
In, Out, Thru
Full Speed USB rev 1.1
AC oder DC, 12V, 1.5 A
44,3 x 483,0 x 189,5 (1HE)
2,9 kg
Anschlüsse der Klangbox:
Gewährleistungsbestimmungen
Für die Hardware des beschriebenen Produktes gelten die gesetzlichen Bestimmungen zur Produktmängelhaftung der Bundesrepublik Deutschland.
Die CreamWare Audio GmbH (“CreamWare”) gewährleistet für das beschriebene Produkt, dass es bei der
Herstellung frei von Material- und Herstellungsmängeln ist. Hierfür wurde jedes einzelne Gerät von unserer
Qualitätssicherung vielfach und sorgfältig getestet, bevor es ausgeliefert wurde. Bitte beachten Sie daher bei etwaigen Mängeln die nachfolgend aufgeführten HInweise.
Innerhalb von 6 Monaten nach Erwerb wird CreamWare bei physikalischen Mängeln an der Hardware diesen
Mangel kostenfrei für Sie beheben. Die Behebung erfolgt in der Regel durch Reparatur oder Instandsetzung.
Kann auch nach dreimaliger Reparatur der aufgetretene Mangel nicht behoben werden, besteht ein Anspruch auf Wandlung oder Rücktritt vom Kauf. Kann bei der Überprüfung kein physikalischer Mangel festgestellt werden, ist die Überprüfung kostenpflichtig.
Im Zeitraum von 6 bis 24 Monaten nach Erwerb hat der Erwerber den Nachweis zu führen, dass der aufgetretene
Mangel bereits bei Auslieferung vorhanden war. In diesem Fall wird die Reparatur oder Instandsetzung nach
Vorlage der entsprechenden Nachweise ebenfalls kostenfrei durchgeführt. In allen anderen Fällen ist die
Instandsetzung kostenpflichtig. Für den Erfolg durchgeführter Instandsetzungsmaßnahmen kann insbesondere nach Ablauf der Gewähleistung keine Gewähr übernommen werden.
Transportschäden an Produkten sind innerhalb von 14 Tagen nach Erhalt CreamWare schriftlich zur Kenntnis zu geben. Für den Anspruch auf Durchführung einer Instandsetzung aus Gewährleistung ist das Produkte unter
Angabe von Name und Wohnsitz zu registrieren oder bei Einsendung eine Kopie des Kaufbelegs beizufügen.
Bei Rücksendungen kontaktieren Sie bitte den Händler, bei dem Sie das Produkt erworben haben zur weiteren
Bearbeitung. Alternativ können Sie auch bei CreamWare vor Rücksendung eines defekten Produktes eine RMA
Nummer erhalten, die bei der Rücksendung unbedingt anzugeben ist, um Verzögerungen in der Bearbeitung zu vermeiden. Fügen Sie nach Möglichkeit eine detaillierte Fehlerbeschreibung bei, damit eine Reparatur auch in
Ihrem Interesse zügig durchgeführt werden kann.
Bei Schäden durch Mißbrauch, Unfall, Fahrlässigkeit, eigenmächtige Eingriffe, Änderungen oder Modifikationen am Produkt einschließlich der Betriebssoftware sowie mechanischer oder elektronischer Bauteile oder bei
Schäden, die auf Nichtbeachtung der in dieser Anleitung gegebenen schriftlichen Anweisungen für ordnungsgemäßen Einbau, Wartung und Benutzung zurückführbar sind, entfällt jeglicher
Gewährleistungsanspruch.
CreamWare Audio GmbH
Tel.
++49 (0) 2241 59 58 0
Fax ++49 (0) 2241 59 58 57 email [email protected]
Hiermit wird bestätigt, dass die CreamWare-Hardware den Anforderungen entspricht, die in der
Richtlinie des Rates zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über die elektromagnetische Verträglichkeit (89/336/EWG) festgelegt sind.
CreamWare Audio GmbH, Oktober 2006 gez. Wolf Roth
CreamWare Audio GmbH
Am Turm 11 - 13
53721 Siegburg
Germany
Register HRB 5804, AG Siegburg
VAT-ID: DE813874968
Tel.: +49 2241 59 58 0
Fax +49 2241 59 58 57 www.creamware.de
www.creamware.com

Public link updated
The public link to your chat has been updated.
Advertisement