Exsys EX-1324-37P USB 2.0 to 4S x RS-232 ports Owner's Manual
EXSYS EX-1324-37P is a cable that allows you to connect up to four RS-232 serial devices to your computer via a single USB port. The device is compatible with USB 2.0 and 1.1 and supports a variety of operating systems, including Windows XP/7/8.x/10/CE/Server 2012R2, Linux, and MAC OS.
The EX-1324-37P is a hot plug & play device. Each serial port has a FIFO 16C550 port for high-speed data transfer. The device also includes an octopus cable with four 9-pin connectors for easy connection to your serial devices.
Advertisement
Advertisement
CONNECTORS
DB37F:
(Picture 1)
7
8
9
10
11
12
13
Serial 37 Pin D SUB connector female :
Pin Signal Pin Signal
1
2
NC
DCD4
14
15
RXD2
RI1
3
4
5
6
GND
CTS4
RXD4
RI3
16
17
18
19
DTR1
DSR1
RTS1
TXD1
DTR3
DSR3
RTS3
TXD3
DCD2
GND
CTS2
20
21
22
23
24
25
26
RI4
DTR4
DSR4
RTS4
TXD4
DCD3
GND
34
35
36
37
30
31
32
33
Pin
27
28
29
Signal
CTS3
RXD3
RI2
DTR2
DSR2
RTS2
TXD2
DCD1
GND
CTS1
RXD1
DRIVER INSTALLATION
Windows
After the hardware installation Windows will recognize the device automatically and install the drivers. If the driver shoul not be installed automatically, please insert the Driver CD into your
CD Rom drive (e.g. Drive D:) and open the folder „ USB_to_IO/FTDI “. Please select the folder with your operating system and install the driver (see Picture). Follow the hardware assistant and finish the installation. Important! Restart your PC in any case after installing the drivers.
Anleitung
Vers. 1.0 / 22.07.21
AUFBAU
EX 1324 37P
4 x 9 Pin Stecker
DB9M:
(Picture 2)
Serial 9 Pin D SUB connector:
Pin Signal Pin
1
2
3
CDC
RXD
TXD
4
5
6
Signal
DTR
GROUND
DSR
Pin
7
8
9
Signal
RTS
CTS
RI
HARDWARE INSTALLATION
Because there are large differences between PC ’ s, we can give you only a general installation guide for the EX 1324 37P Please refer your computer ’ s reference manual whenever in doubt.
1.
Plug the USB Type A end of the Adapter cable into the USB host port of your PC or into an available USB port on a USB hub
2.
Connect the RS 232 Serial Devices to the DB37 pin female connectors (Picture 1).
3.
Proceed with the next section “ Installing Drivers ” to install the virtual COM port drivers for your Operating System.
CLEANING
For cleaning please use only a dry fluff less cloth and remove the dirt with gently pressure. In the area of the connectors please make sure that no fibres from the cloth remain in the connectors. Attention! Never use a moist or wet cloth for cleaning!
37 Pin Buchse für
4 x Serielle Ports
BESCHREIBUNG & TECHNISCHE DATEN
USB A Stecker zum PC
Die EX 1324 37P ist ein Kabel mit Umsetzung von USB 2.0 auf vier RS 232 Schnittstellen mit
FIFO 16C550 Ports für den Anschluss von High Speed Seriellen RS 232 Peripherie Geräten
(z.B. Modem, Plotter usw.). Sie hat eine 37 Pin Buchse für den Anschluss der Seriellen Geräte
(Pin Belegung gemäss Bild 1) an diese ein Octopus Kabel mit 4 x 9 Pin Stecker angschlossen werden kann. Die EX 1324 37P ist Hot Plug & Play. Für die Einstellungen der I/O Adressen und Interrupts sind keine Jumper und Einstellungen notwendig. Sie werden vom System BIOS und beim Installieren des Betriebssystems automatisch vorgenommen.
Kompatibilität:
Betriebssysteme:
Anschlüsse:
Lieferumfang:
Zertifikate:
USB 2.0 und 1.1 Anschluss
Windows 9.x/ME/ XP / 7/ 8.x/ 10/ CE/ Server 2012R2, Linux, MAC OS
1x USB A Stecker
1 x 37 Pin Buchse für vier Serielle Geräte
4 x 9 Pin Stecker vom Octopus Kabel
EX 1324 37P, Treiber CD, Anleitung, Octopus Kabel mit 4 x 9 Pin
ANSCHLÜSSE
USB A Stecker:
USB 2.0 A Buchse:
Pin Signal
1
2
VCC
DATA -
Pin
3
4
Signal
DATA+
GND
Achtung!
Stecker nie umgekehrt oder mit
Gewalt einstecken.
5 6 1
ANSCHLÜSSE
DB37F:
(Bild 1)
7
8
9
10
11
12
13
Serial 37 Pin D SUB connector female :
Pin Signal Pin Signal
1
2
NC
DCD4
14
15
RXD2
RI1
3
4
5
6
GND
CTS4
RXD4
RI3
16
17
18
19
DTR1
DSR1
RTS1
TXD1
DTR3
DSR3
RTS3
TXD3
DCD2
GND
CTS2
20
21
22
23
24
25
26
RI4
DTR4
DSR4
RTS4
TXD4
DCD3
GND
34
35
36
37
30
31
32
33
Pin
27
28
29
Signal
CTS3
RXD3
RI2
DTR2
DSR2
RTS2
TXD2
DCD1
GND
CTS1
RXD1
DB 9pin
(Bild 3)
Seriell 9 Pin D
-
SUB Stecker :
Pin
1
2
3
Signal
CDC
RXD
TXD
Pin
4
5
6
Signal
DTR
GROUND
DSR
Pin
7
8
9
Signal
RTS
CTS
RI
TREIBER INSTALLATION :
Windows
Nach Abschluss der Hardwareinstallation erkennt das Betriebssystem automatisch den Adapterund installiert diesen! Falls die Treiber nicht automatisch installiert werden sollten, legen Sie nun die Treiber CD in Ihr CD ROM Laufwerk (z.B. Laufwerk D:) ein und öffnen Sie den Ordner
„ USB_to_IO/FTDI “. Nun wählen Sie den Ordner Ihres Betriebssystems aus und installieren Sie die Treiber (siehe Abbildung). Folgen Sie den Installationsanweisungen und schließen Sie die
Installation ab. Wichtig! Starten Sie Ihren PC nach der Installation neu.
Manual
Vers. 1.0 / 22.07.21
LAYOUT
EX 1324 37P
4 x 9 pin male connector
HARDWARE INSTALLATION
Beachten Sie bitte die folgenden Installationshinweise. Da es grosse Unterschiede bei Computern gibt, können wir Ihnen nur eine generelle Anleitung zum Einbau der EX 1324 37P geben. Bei
Unklarheiten halten Sie sich bitte an die Bedienungsanleitung Ihres Computersystems.
1.
Verbinden sie nur das Ende des USB A Stecker von der EX 1324 37P G an die USB 2.0 A -
Buchse ihres Computer Systems oder einen freien USB Anschluss ihres USB Hub ‘ s.
2.
Verbinden Sie die RS 232 Serielle Geräte an die DB 37 Pin Buchse der EX 1324 37P G.
3.
Installieren Sie jetzt die Treiber und gehen zum nächsten Abschnitt „ Treiber Installation “.
REINIGUNG
Zur Reinigung des Gerätes verwenden Sie bitte ausschließlich ein trockenes nicht faserndes
Tuch und entfernen Sie die Verschmutzung mit leichtem Druck. Im Bereich der Anschlüsse bitte darauf Achten, dass keine Fasern des Tuchs in der Buchse hinterlassen werden. Verwenden
Sie bitte zu Reinigung in keinem Fall ein feuchtes oder nasses Tuch!
37pin female connector for
4 x serial ports
DESCRIPTION & TECHNICAL INFORMATION
USB A male to the PC
The EX 1324 37P is a cable with conversion from USB 2.0 to four RS 232 interfaces with FIFO
16C550 ports for the connection of high speed serial RS 232 peripheral devices (e.g. modem, plotter etc.). It has a 37 pin connector for the connection of the serial devices (pin assignment according to picture 1) to which an Octopus cable with 4 x 9 pin connectors can be connected.
The EX 1324 37P is hot plug & play. For the settings of the I/O addresses and interrupts no jumpers and settings are necessary. They are done automatically by the system BIOS and when installing the operating system.
Compatibility:
Operating system:
Connectors:
USB 2.0 and 1.1
Windows XP / 7/ 8.x/ 10/ CE/ Server 2012R2, Linux, MAC OS
1x USB A male connector
1x 37 pin female connector for 4 serial port
4 x 9 pin female connector from the Octopus cable
Extent of delivery: EX 1324 37P, Driver CD, Manual, Octopus cable with 4 x 9 pin
Certificates:
CONNECTORS
USB A male:
USB 2.0 A male connector:
Pin Signal Pin
1
2
VCC
DATA -
3
4
Signal
DATA+
GND
Attention!
Never plug in with force or in wrong direction.
2 3 4

Public link updated
The public link to your chat has been updated.
Advertisement