24187247
Concealed Vertical Rod Touchbar Panic Device
HH 1690
Installation Instructions
NOTE: The door prep for the HH 1690 Device is different than the standard 1690 Device. Please verify prep required (page 4) before prepping the door.
Index:
• Parts List ...................................
2
• Touchbar Part Numbers ............
3
• Before Installation .....................
• Template ...................................
3
4
Customer Service
1-877-671-7011 www.allegion.com/us
© Allegion 2014
Printed in U.S.A.
24187247 Rev. 09/14-c
15
12 13
6
14 26
24
23
27
11
PARTS LIST
1
18
19
Top Rod
Assembly
23
24
25
3
2
NOTES
1.
See page 3 for touchbar part numbers.
2.
Touchbar shown cut away for visibility.
9
4
10
22
10
21
5
RHR shown
17
16
8
20
RIM CYLINDER
(optional; sold separately)
Finish Part No.
DC13
DC35
4270107367
4270105986
US4
US10
032210-10
032210-06
US26/28 4270100247
7
Hex Bottom
Rod
Assembly
21
2
2
3
4
5
6
Package No. PKG.150 (US28 finish) or
Package No. PKG. 151 (DC13/DC35 finish)
Item Quantity Description
1 4 #10-32 x 1/4" UFPHMS
US28 finish
2
4
2
1
1
DC13/DC35 finish
Rod bearing bushing
Retaining ring
1/4-20 x 1/2" FPHMS
Traveler lift bracket
5/32" hex dogging key
Part No.
963125-00
4270902255
BUSH.108
RRING.108
SCREW.1052
BRKT.138
4270106944
Package No. CYLASY.1083
Note: Optional. Required with rim cylinder only.
Item Quantity Description
7 1 Cylinder bushing
Part No.
4270100663
10
11
8
9
1
1
1
1
Pinion cam
Retractor
Retainer screw
Pinion support bracket
4270100566
4270903161
SCREW.1049
BRKT.133
Package No. 4270902993
Note: For use with EO and DT devices only.
Item Quantity Description
10 1 Retainer screw
11 1 Pinion support bracket
Part No.
SCREW.1049
BRKT.133
Package No. ECAP.130
Item Quantity Description
12
13
14
15
2
1
1
2
1/4-20 x 1/2" PPHMS
Part No.
4299100074
Channel end cap ECAP.127
Hinge stile touchbar end cap ECAP.128
#8 x 1-1/4" FPHTF 4299101314
Package No. COVER.113
Item Quantity Description
16
17
1
2
Center case cover
Part No.
COVER.112
#8 x 5/8" PPHTC Sems 4299101318
Package No. 23955255-00
Note: Contains strike and four mounting screws.
Item Quantity Description
18 1 Strike
Part No.
Strk. 134
19 4 12x24 1/2" UFPHMS 964064-00
Package No. Guide 102 (US28 finish) or
Package No. Guide 103 (DC13/DC35 finish)
Item Quantity Description Part No.
20
21
1
4
HH hex rod guide
10-32 x 3/8" FPHMS
4270109237
US28 finish
DC13/DC35 finish
4299100659
4299101011
Item Quantity Description
22 1 Lift arm
23
24
25
2
2
2
#8 x 3/4" FPHTF
Touchbar pin
Touchbar anchor
26
27
28
1
1
1
Part No.
BRKTASSY.107
4299101313
PIN.125
BRKT.128
Lock stile touchbar end cap ECAP.129
Dogging spring
Dogging assembly
DC13/DC35 finish
US28 finish
971493-89
KIT.1022
KIT.1021
TOP ROD
ASSEMBLY
HH latch
23955289
Jam nut 3/8"-24
4299100004
Top rod quantity 1 piece
Bent rod 35.125" long
4270100017 (7' door)
(can be shortened by 5")
Bent rod 47.125" long
4270100018 (8' door)
(can be shortened by 13")
PARTS LIST (CONTINUED)
STRAIGHT HEX BOTTOM
ROD ASSEMBLY
Bent rod 37.812" long
4270101825
(can be shortened by 6")
Jam nut 3/8"-24
4299100004
Straight Hex bolt
4270101830
TOUCHBAR PART NUMBERS
Finish
30" Nominal Device Length
(24.785" Extrusion Length)
36" Nominal Device Length
(30.785" Extrusion Length)
42" Nominal Device Length
(36.785" Extrusion Length)
48" Nominal Device Length
(42.785" Extrusion Length)
Without
Dogging
Hole
With
Dogging
Hole
Without
Dogging
Hole
With
Dogging
Hole
Without
Dogging
Hole
With
Dogging
Hole
Without
Dogging
Hole
With
Dogging
Hole
DC13
DC35
US3
US10
US26
US26D
US28
EXT.825
EXT.826
EXT.2323
EXT.2333
EXT.2338
EXT.2340
EXT.830
EXT.828
EXT.829
EXT.2351
EXT.2352
EXT.2353
EXT.2354
EXT.827
EXT.399
EXT.400
EXT.2324
EXT.2334
EXT.2339
EXT.2289
EXT.398
EXT.609
EXT.631
EXT.2355
EXT.2356
EXT.2357
EXT.2358
EXT.608
EXT.439
EXT.441
EXT.2341
EXT.2345
EXT.2349
EXT.2350
EXT.438
EXT.736
EXT.737
EXT.2359
EXT.2360
EXT.2361
EXT.2362
EXT.646
EXT.443
EXT.444
EXT.2298
EXT.2303
EXT.2304
EXT.2294
EXT.442
EXT.739
EXT.740
EXT.2363
EXT.2364
EXT.2365
EXT.2366
EXT.738
BEFORE INSTALLATION
1. Check “Parts List” (see page 2).
2. Prepare door using template on page 4.
3. Set initial rod lengths (see ININST.1002 page 11). Rods are factory set for standard 7’ door.
4. If door width is non-standard, cut device (see ININST.1002 page 12).
5. If necessary, re-hand device (see ININST.1002 page 11).
6. Continue with installation instructions in sheet ININST.1002.
3
1-1/32"
9/16"
1/8"
2-1/4"
1-1/2"
3/4"
Lock stile
15/64" dia.
drill thru, c'sink with 5/16" dia.
tool, 2 holes, for cylinder; see Detail A
1-1/2"
7/16"
3"
1/4"
1-1/2"
5/8"
1/2"
41-5/16" to bottom of door; dimension C for setting rod lengths
1-3/8"
7/8"
2-3/8"
1"
Cutout on inside face only
1/4" radius
#9 (0.196") drill, c'sink 82° to 25/64" dia., 5 holes, inside face only
13/32"
13/16"
1-3/16" dia. hole, outside face only, for cylinder only
9/16" dia. ream for cylinder only
11/16"
Hinge stile
With HH
Rods and Latches
Door height
HH 1690 Touchbar
Concealed Vertical Rod
Panic Device
Door Preparation Template
Lock stile
Pull side
Push side
LHR shown
RHR opposite
Hinge stile
3/4"
3/8"
5/16"
#7 (0.201") drill thru,
1/4-20 tap,
4 holes
3/4" min.
Rod type latch location
See Note D
NOTES
1.
All holes inside face only except as noted.
2.
All dimensions for 1-3/4" thick, 1/8" wall doors.
Consult factory for others.
Face of door blade stop
Door clear opening
Bottom of door
3/64"
of top latch
2x #16 drill & tap 12-24 use strike as template once final strike location is set
3/4"
Blade stop
3/4" 3/4"
2x #16 drill tap 12-24
4
Bottom Plan View, Head Jamb (looking up)
Showing Upper Strike Mounting Holes
29/32"
Blade stop bottom latch
3/4" dia. cut strike opening for bottom latch thru threshold
Top Plan View, Rod Latch
Showing Strike Cutout in Threshold for Round Latch
5/16" dia.
x 82° countersink
Detail A
(for cylinder)
