Aubrey - 3ft Bed
Assembly Instructions
- Please keep for future reference 531/3826
553/2975
745/2424
765/7236
Dimensions
Length - 200,5cm
Width - 106,2cm
Height - 110cm
Important
– Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, ca l l t h e customer Helpline: 03456 400 800
Issue 11 - 26/05/20
Safety and
Important – Please read these instructions fully before starting assembly
. Check you have all the components and tools listed on pages 2 and 3.
.
Assemble on a soft level surface to avoid damaging the unit or your floor.
.
Remove all fittings from the plastic bags and separate them into their groups.
.
Keep children and animals away from the work area, small parts could choke if swallowed.
.
Make sure you have enough space to layout the parts before starting.
. This product contain natural timber. You may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
.
Do not stand or put weight on the product, this damage.
could cause
.
Assemble the item as to its final position (in room) as possible.
close the same
.
We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit.
Only use hand screwdrivers.
.
Parts of the assembly will be easier with
.
Dispose of
2 people.
all packaging carefully and responsibly.
1 care and maintenance
.
Use an appropriate furniture polish for natural wood furniture and a dry clean the product.
cloth to
. Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age.
.
From time to time check that there are no loose screws on this unit.
.
This product should not be discarded with household waste.
Take to your local authority waste disposal centre.
Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
01 Headboard (106,2 x 110,0cm) 03 Side rails x 2 (190,0 x 11,5cm)
02 Footboard (106,2 x 60,0cm) 04 Slats x 13 (91,5 x 6,8cm)
2
Components - Fittings
If you have damaged or missing components, call theCustomer Helpline: 03456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
90mm Bolt 1/4 x 04
D
40mm Wooden dowel x 04
G
Spanner x 01
J
Spacer 84mm x 02
B
Half-Moon Nut 1/4 x 04
E
35mm Screw x 26
H
Nut 1/4 x 04
C
Allen key x 01
F
Washer 1/4 x 04
I
70mm Headless Bolt 1/4 x 04
Tools required
Phillips screwdriver
(medium & large)
2 m
Ruler/tape measure
3
Small hammer
Eye protection
(when using a hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step
1
Fitting dowels
Insert dowels D into the indicated parts.
03
03
D
D
D
D
D
Step 2
Assembling side rails
A: Screw headless bolt
I
Do not over tighten.
B : Insert washer to the footboard to side rails.
A:
B:
02
F
F
03
H
H
G
G
I
50mm
I
Do not over tighten the bolts, see indicative measure.
03
02
4
Assembly Instructions
Step 3
Assembling side rails the headboard. Insert
B
B
Then fix them to the
A
03
B
01
B
03
A
C
A
C
Step 4
Fixing slats centralize slats in bed frame prior to fixing. Fix shown.
Fix slats in one side first, then fix them in the other side by pushing the rail against the slats if necessary.
Periodically check that all screws are tight.
E
J
J
E
E
J
J
04
5
Assembly Instructions
Step 5
Additional step to fixing slats
Warning!
Make sure that s slats screws never collide to the screws on the slats support bar, as shown in the diagram.
collide.
Assemble is complete!
6
