Gefran GIG Inclinometer User Manual

Add to my manuals
6 Pages

advertisement

Gefran GIG Inclinometer User Manual | Manualzz
GIG-RELAY
DUAL AXIS GENERAL TILT SENSOR
Relay output (XY)
Code 85205B Edition 03-2019
SUMMARY
1. NOTICE����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������2
2. INTRODUCTION��������������������������������������������������������������������������������������������������������������������������������������������������������������������2
3. 3. ELECTRICAL CONNECTIONS������������������������������������������������������������������������������������������������������������������������������������������3
4. RELAYS: FUNCTIONAL DIAGRAM AND CONTACTS RATING��������������������������������������������������������������������������������������������5
5. AUTOZERO FUNCTION (additional function)������������������������������������������������������������������������������������������������������������������������6
85205B_GIG-RELAY_Operative Manual_03-2019_ENG
1
1. NOTICE
Please observe all proper safety rules and regulation for electrical devices when installing this inclinometer.
In addition, the following recommendations are made:
a)
b)
c)
d)
e)
f)
Do not apply power to the inclinometer during installation
Avoid applying any mechanical pressure or stress to the housing
Do not exceed the maximum fastening torque for mounting screws and make use of conical spring washer
Hand tighten mating connector. DO NOT use pliers as damage may occur.
Should the inclinometer fail to operate properly, consult this manual for possible solutions.
Do not attempt to open the inclinometer, as damage may occur.
For other troubleshooting measures, please contact our service team.
2. INTRODUCTION
The GIG M12 (8 pole) or cable output (8 wires) 2-axis (digital switching points from ±1.5° to ±60°) inclination sensor with
two relays output interface enables angle levelling and position detection in many applications.
The sensor is based on state-of-the-art MEMS capacitive technology whereby the sensor has a very compact and flat
design and is therefore particularly well-suited for tight installation spaces.
Due to high protection class IP67, the sensor is perfectly suited for use under damp or polluted conditions.
Both tilt switches can be specified for a variety of applications. In addition, the two relays output can be combined. Depending on the requirements, a turn-on and turn-off delay can be defined at the switching output.
2
85205B_GIG-RELAY_Operative Manual_03-2019_ENG
3. ELECTRICAL CONNECTIONS
For the connections refer to the table below:
Meaning
1
+ Supply [+ 10 … + 36 Vdc]
2
NC (should not be connected)
3
NC (should not be connected)
4
Ground
5
Relay 1 NO/NC (depending on order selection)
7
Relay 2 NO/NC (depending on order selection)
6
Relay 1 COM
8
Relay 2 COM
Important Note:
use conical spring washer M5 DIN6796 A2 (3 pcs)
35
CONEC M12x1
8 pole
Metal insert
Maximum
torque: 2.5Nm
28
70
84
73
85205B_GIG-RELAY_Operative Manual_03-2019_ENG
3
For the connections refer to the table below:
Meaning
WHITE
+ Supply [+ 10 … + 36 Vdc]
BROWN
NC (should not be connected)
GREEN
NC (should not be connected)
YELLOW
Ground
GREY
Relay 1 NO/NC (depending on order selection)
BLUE
Relay 2 NO/NC (depending on order selection)
PINK
Relay 1 COM
RED
Relay 2 COM
35
Important Note:
use conical spring washer M5 DIN6796 A2 (3 pcs)
84
73
Cables output IEC 60332
Cable output - 0.5mm² OD 6.4mm
24
28
70
Metal insert
Maximum
torque: 2.5Nm
IEC 60332 Cable
output 0.5mm²
OD 6.4mm
4
85205B_GIG-RELAY_Operative Manual_03-2019_ENG
4. RELAYS: FUNCTIONAL DIAGRAM AND CONTACTS RATING
Important Note:
The two relays output Relays 1 and Relays 2 can be combined and programmed. The contact form is selectable
N.O.(normally open) or N.C.(normally close) during order phase.
Due to safety reason the selected contact configuration is valid in case of switched-on operating voltage in the zero position (with K1 and K2 coils active).
Contact Rating:
Relay 1 and Relay 2
Max. switching voltage
120VDC, 125VAC
Rated current @ 85°C
1.25A
Switching power
30W, 62.5VA
Contact material
AgPd, gold plated
Initial contact resistance
100mΩ at 10mA, 20mV
Electrical endurance: at 24VDC / 1.25A
min. 3x10⁵ ops
85205B_GIG-RELAY_Operative Manual_03-2019_ENG
5
5. AUTOZERO FUNCTION (additional function)
To activate the Autozero function make sure that:
- sensor is powered
- fixing surface is free of dust or grease
- sensor is fixed on the horizontal plane with suitable screws
ATTENTION!
The Autozero function can be defined within a maximum range of +/- 4.5° from the original zero position (factory set).
Hold the magnetic pen ① (accessory to order-PKIT312) to the ZERO POINT
②.
indicated on the product label
Hold the position for at least 3-5 seconds so that the operation is successful.
①
②
GEFRAN spa
via Sebina, 74 - 25050 PROVAGLIO D’ISEO (BS) - ITALIA
tel. 0309888.1 - fax. 0309839063 Internet: http://www.gefran.com
6
85205B_GIG-RELAY_Operative Manual_03-2019_ENG

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement