Angled Extractor

LAM2703 60cm Stainless Steel

LAM2704 60cm Black

LAM2705 90cm Stainless Steel

LAM2706 90cm Black

Instructions and Installation

www.howdens.com/appliances-registration

GU

LA

M

ON

A APPLIAN

3

YEARS

CE

E

ARANTE

Free 3 year guarantee

Call now

1

0333 010 0009

Alternatively, visit www.howdens.com/appliance-registration

3 year guarantee available.

Register your appliance within 90 days

2

By registering your appliance and creating an account, we will keep you up to date with the latest product information and notify you immediately of any important product updates

1 Lines are open Monday to Friday 9am to 5pm. Calls will be charged at your local rate and may be recorded and monitored for training and quality purposes.

2 So that in the event of an important product update, or recall, we can contact you.

LAMONA Appliances

Dear Customer,

Congratulations on your choice of a LAMONA domestic appliance.

The user manual will help you use your product quickly and safely.

• Please read this user manual before installing and using the product.

• Always follow the safety instructions.

• Keep this user manual within easy reach for future reference.

• Please read any other documents supplied with the product.

Explanation of symbols

Throughout this user manual the following symbols are used:

Important information or useful tips about usage.

Warning for possible hazards to health and property.

Warning possibility of electric shock.

Energy Efficiency

In order to optimise efficiency of the product and reduce environmental impact we recommend the following:

• Product is installed in ducted configuration, using maximum Ø of ducting advised in this manual, ducting as straight and as short as possible.

• Any filters are cleaned/replaced when necessary to maintain good airflow and grease filter efficiency.

• Switch on the hood at the minimum speed required to clear unwanted cooking odours.

• Switch off lighting when not in use or not required.

Metal Surfaces of the Extractor and Condensation

When cooking with pans using a large water content, large quantities of vapour and steam can be produced very quickly. This steam may condense onto the cold metallic surfaces of the extractor and even the splash back area if tiled, glazed etc.

(This is not a fault with either the hob or extractor if correctly installed.)

The amount of this condensation on any particular surface will depend on many factors including the ambient temperature in the kitchen, the related ambient temperature of the metal surfaces, the general ventilation within the kitchen, the type of food being cooked and the duration. Using lids on pans can help reduce the amount of steam being released and subsequent condensation.

This product’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your product also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2012/19/EU on Waste Electrical and Electronic

Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

By placing the marking on this product, we declare, on our own responsibility, compliance to all of

European safety, health and environmental requirements stated in the legislation for this product.

Page _ 2 www.howdens.com

Index

Before Using The Extractor

Safety

General

Safety for children

S a f e t y when working with electricity

General Information and Operation

E x rt a c t o r layout

Control panel layout

Care and maintenance

General cleaning

Grease filters

Carbon filters

Replacing the lamps

Installation

Methods of extraction

Extraction via ducting

Extraction via recirculation

Parts identification

Hanging your extractor

Decorative chimney fitting

Electrical connections

Troubleshooting

Technical Specification

Your Guarantee

13

13

14

04

04

04

04

04

05

05

05

09

10

11

12

08

08

08

08

06

06

06

07

07

User manual LAM2703 2704 2705 2706

Exclusive to Howdens Joinery.co

Page _ 3

LAMONA Appliances

Before Using the Extractor

• Make sure that you have removed all packaging, wrappings, stickers and from the Extractor

• It is recommended that you clean the extractor’s surface before using for the time.

Safety

This appliance is for domestic extraction purposes only. It must not be used for other purposes. Commercial use will void the guarantee.

• Keep all ventilation slots clear of obstructions, as this may cause premature failure of the appliance

The manufacturer shall not be liable for any damage caused by improper use, installation or handling errors

General

This product is not intended to be used by persons with physical, sensory or mental disorders or unlearned or inexperienced people (including children) unless they are supervised by a person who will be responsible for their safety or who will instruct them accordingly in the use of the product.

• Do not trap the mains cable and do not route it over surfaces which may become hot. The cable insulation may melt and cause a as a result of a short circuit.

• Make sure that the product function buttons are switched off after every use.

• Product must be installed by a person in accordance with the regulations in force otherwise, the guarantee may become void.

• Do not operate the product if the power cable is damaged. Call service agent.

• Do not carry out any repairs or on the product. However, you may remedy some the problems that do not require any repairs or See Troubleshooting, at the rear of this manual.

• Never wash down the product with excessive water, as there is the risk of electric shock!

Safety for children

Electrical products can be dangerous to children.

Keep children away from the product when it is operating and do not allow them to play with or near the product.

The packaging materials will be dangerous for children. Keep the packaging materials away from children. Please dispose of all parts of the packaging according to environmental standards.

• Never use the product when your judgment or coordination is impaired by the use of alcohol and/or drugs.

• Product must be disconnected from the mains during installation, maintenance, cleaning and repair procedures.

Safety when working with electricity

In case of any damage, switch off the product and disconnect it from the mains. To do this, turn off the fuse at the fuse box.

Make sure that fuse rating is compatible with the product.

• Repair procedures must always be performed by service agents. The manufacturer shall not be held responsible for damages arising from procedures carried out by unauthorised persons, which may also void the guarantee.

• DO NOT flambè under the extractor.

Page _ 4 www.howdens.com

General Information & Operation

Extractor layout

1.

Upper Chimney Section

2.

Recirculation Vent

3.

Lower Chimney Section

4.

Fan and Light Controls

5.

Extractor Body

User manual LAM2703 2704 2705 2706

3.

5.

1.

2.

4.

Control panel layout

Extractor Light On/Off & Delay Function (Hold for 5 Seconds)

1 .

Extractor Power Level 1

2 .

Extractor Power Level 2

3 .

Extractor P ower Level 3

(3i Intensive - push twice)

1 2 3 i

Delay function

The delay function will automatically switch off the hood 5 minutes after setting. The delay function can be activated on all power functions. When on press and the hold the light icon for 5 seconds, the power level will flash when activated. It can be ended sooner by pressing either the light or power level icon again.

NOTE: The light remains on once the delay function has ended.

Intensive Function

On power level 3, push twice to activate intensive speed. Intensive speed runs for 6 minutes after which the hood switches off automatically. Press power level 3 again to deactivate.

Exclusive to Howdens Joinery.co

Page _ 5

LAMONA Appliances

Care and Maintenance

Before cleaning or attempting any type of maintenance, always make sure that the electricity supply is disconnected.

CAUTION: Accessible parts may become hot when used with cooking appliances.

The manufacturer declines all liability in cases where the instructions for the appropriate installation, maintenance and use of the extractor hood are not observed.

If the power cable is cut or damaged in any way, disconnect the extractor from the electricity supply and call the service number on the rear cover of this booklet or a suitably repairer.

General cleaning

Wipe the external surfaces of the appliance regularly using warm water and a mild detergent. NEVER use abrasive cleaners, or strong household cleaners as they may affect the appearance of the product and /or artwork on the control panel, voiding the manufacturers warranty.

The grease filters

The grease filters should be cleaned every two months or sooner depending on the type of cooking being performed.

The grease is of a metallic material and should be washed regularly using a neutral detergent, it can be cleaned in a dishwasher.

Grease filters should be washed separately to crockery and kitchen utensils.

Grease filters should be thoroughly dried before reinstalling on the extractor.

1 Push latch to remove

2 Lower

Installation is the reverse of the removal process.

1

2

Page _ 6 www.howdens.com

User manual LAM2703 2704 2705 2706

The carbon filters (supplied separately)

•

•

Before attempting to change or fit the charcoal filters ensure power to the extractor is switched off.

Carbon filters only required for recirculation mode.

Carbon have a limited life. We advise you to change them when there is a noticeable drop in performance. The intervals between changing the will depend entirely upon the amount of cooking you do, but on average they will last about 3 months. Please quote the part reference number LAM2004

(pack of 2) when reordering.

• To gain access to the carbon filters, first of all remove the grease filters as above.

• Remove the old filters and install new charcoal filters by turning them gently.

Refit grease filters.

Reconnect the power supply.

NOTE: The suction will be lower when installed in recirculation mode, this is normal and not a product fault.

Replacing the lamps

The lamps on this model are service fix only and replacement should be carried out by an authorised service agent.

The extractor hood is fitted 1W LED lamps which will give many years of reliable service.

In the event of one of the lamps failing please call the service number.

The lamps on this appliance should only be used during operation of the cooker hood. They should not be left on permanently and used as a main lighting source. The extractor is for domestic use only.

Exclusive to Howdens Joinery.co

Page _ 7

LAMONA Appliances

Installation

Methods of extraction

The very best method of clearing the kitchen of unwanted odours is by connecting the appliance to an exhaust duct and venting to the outside atmosphere via the ceiling or an exterior wall. (Suitable ducting kits may be purchased from the depot where you bought the extractor.) You do not need charcoal using the external ducting mode.

when

Vent through external

wall or ceiling

Filtered air recirculated

Ducting kit (APL2805/6/7)

Supplied Separately

Fig 1.

Ducting mode

(No charcoal required)

Fig 2.

Recirculation mode

(Charcoal LAM2004 required)

Extraction via ducting

Never use the hood in areas where devices with exhaust pipes connected to the outside are already operating unless perfect ventilation can be guaranteed.

There shall be adequate ventilation in the room when the extractor is used at the same time as an appliance burning gas or other fuels.

• Connect the external ducting kit to the outlet of the extractor.

Charcoal filters are not required if the extractor is to be ducted out.

Tips for ducting optimal air extraction:

• Keep duct work short and straight.

• Do not reduce the size or diameter of the duct.

• Keep ductwork taut to minimise pressure loss.

Extraction via recirculation

For extraction via recirculation, attach 2 charcoal

to the sides of the motor inside the hood.

These can be ordered separately quoting part

(LAM2004).

switched off.

• Remove the grease

• Align the carbon over the pins located on either side of the fan motor.

• Turn the carbon gently, until you feel them click into position.

• Replace the grease supply it turned back on.

before the power

Page _ 8 www.howdens.com

User manual LAM2703 2704 2705 2706

Part indentification

On opening your box you will the extractor body, a two-piece telescopic decorative chimney, a bag of wall and screws, two brackets, and an outlet reducer.

1. 2.

3.

4.

5.

10 .

6.

7.

8.

9.

1. Main Extractor Body

2. Lower Chimney

3. Upper Chimney

4. Outlet Reducer

5. Body fixing screws

6. Upper Chimney Screws

7. Lower Chimney Screws

8.

Raw Plugs

9.

Chimney Brackets

10. Cable Grid

Exclusive to Howdens Joinery.co

Page _ 9

LAMONA Appliances

Hanging your extractor

This instruction must be strictly adhered to. Failure to comply could result in overheating and serious damage to your appliance. It is recommended that the installation is carried out by two people.

Before drilling or chiselling the ceiling or wall, check for pipes and power cables.

• If ducting externally ensure the ducting tube is kept as short as possible and with the minimum of bends to permit the smoothest (Maximum length 3 metres.). Ducted air must not be discharged into a which is used for exhausting fumes from appliances supplied with energy other than electricity. (E.g. gas boilers)

• Ensure the requirements of the local authorities are adhered to concerning the discharge of exhaust air.

• Ensure adequate room ventilation is provided when the extractor is used in the same room as appliances supplied with energy other than electricity.

• Never duct into a hot air such as a central heating duct

1.

Remove the grease

2.

The recommended

before trying to install.

height for the hood is 700mm above the a minimum of 465mm above the top of the hob if required.

hob. This can be reduced to

3.

Mark and drill the holes required to mount the extractor body, fit the screws in holes ( A ).

4.

With the help of an assistant, hang the extractor body on the upper screws ( A ) and secure in position with the lower mounting screw ( B ).

Ensure extractor is installed level above the worktop.

A

1 2

A

A

380mm Max

Duct = 20mm Min

Recir = 170mm Min

A

260mm

A

B

3

B

B

Page _ 10

Gas Electric www.howdens.com

User manual LAM2703 2704 2705 2706

Decorative chimney fitting

1.

Connect the extractor to the electricity supply (see electrical connections page). We recommend an isolation switch that is accessible after installation.

2.

The outlet reducer maybe required depending on your ducting kit (supplied separately).

3.

Fit the appropriate ducting kit if venting externally.

4.

Follow installation steps below.

5.

Fit the carbon filters if required.

6.

Fit cable grid when using in recirculating mode

7.

Refit the grease filters.

1 2

3 4

6

5

Exclusive to Howdens Joinery.co

Page _ 11

LAMONA Appliances

Electrical connections

IMPORTANT: Ensure that the electricity supply is switched off before connecting.

When fitting in recirculation mode (with carbon filters) ensure the cable is shortened or securely held in place to prevent the loose cable from falling back into the motor.

Your appliance must be connected to fixed wiring via the use of a double pole switched fused spur outlet with at least 3mm contact separation, The isolation switch must be accessible after installation. (See technical data for fuse rating).

We strongly recommend the appliance is connected by a suitably qualified person.

The product must be installed in accordance with all local regulations.

The terminology DOUBLE POLE -/+ means that both the live and neutral supplies are switched and disconnected at the same time.

The terminations labelled SUPPLY are the connections for the internal house wiring and the terminations labelled LOAD are for connection to the appliance.

IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:-

Blue.....................Neutral

Brown..................Live

Green/ Yellow.....Earth

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your spur box, proceed as follows;

The wire which is coloured blue must be connected to the terminal which is marked with the letter

‘N’ or coloured BLACK. The wire which is coloured brown must be connected to the terminal which is marked with the letter ‘L’ or coloured RED. The wire which is coloured Green and Yellow must be connected to the terminal which is marked with the letter ‘E’ or Symbol

Fig 3.

Page _ 12

FUSE ON

Blue.

(Neutral)

N

LOAD

L

SUPPLY

DP

13A 250V~

L

LOAD

N

SUPPLY

Brown.

(Live)

Fig 4.

www.howdens.com

User manual LAM2703 2704 2705 2706

Troubleshooting

TROUBLESHOOTING GUIDE

Symptoms Possible Cause

Light functions but fan does not

Lamps fail to operate?

Motor is on but fan does as usual?

The extractor works normally but smells linger?

Product does not operate?

• Motor temp has exceeded and thermal fuse has tripped.

•

•

Solutions

Switch off the extractor and allow it to cool down and the fuse will auto reset.

Check the filter condition and clean or replace as required.

•

•

•

•

•

•

•

Lamps internal fault.

Power is cut (extractor will not function).

Lamp has passed its usable life.

Call the authorised service agent.

Clogged product’s

can reduce the

Check the grease and charcoal (if also ensure any venting is not obstructed?

Clean the grease with warm water and mild detergent, and/or replace any charcoal

Clogged product’s

can reduce the unwanted smells.

and may cause

Clean the grease with warm water and mild detergent, and/or replace any charcoal

The mains fuse maybe defective or has tripped

Product is not connected properly.

Check fuses in the fuse box. If necessary, replace or reset them.

Check all power connections.

If you cannot eliminate the problem after following the instructions in this section, consult your depot or the Authorised Service Agent. Never try to repair a non-functional product yourself.

Metal Surfaces of the Extractor and Condensation

When cooking with pans using a large water content, large quantities of vapour and steam can be produced very quickly. This steam may condense onto the cold metallic surfaces of the extractor and even the splash back area if tiled, glazed etc (This is not a fault with either the hob or extractor if correctly installed). The amount of this condensation on any particular surface will depend on many factors including the ambient temperature in the kitchen, the related ambient temperature of the metal surfaces, the general ventilation within the kitchen, the type of food being cooked and the duration. Using lids on pans can help reduce the amount of steam being released and subsequent condensation.

TECHNICAL INFORMATION

General

Total power consumption

Fuse

Voltage /Frequency

Cable type / section

Cable length

Lamps

142W

3 A

220-240 V ~ 50 Hz

0.75mm², 3 core or equivalent max. 1.5m

2X 1W LED natural white 4000k

Exclusive to Howdens Joinery.co

Page _ 13

LAMONA Appliances

Your guarantee

Product guarantee details (UK only)

Your appliance has the benefit of a comprehensive manufacturer’s guarantee which covers the cost of breakdown repairs. (Details of which are shown on your Proof of purchase Document).

• Any claim during the period of the guarantee MUST BE ACCOMPANIED BY THE PROOF OF

PURCHASE.

• The product must be correctly installed and operated in accordance with the manufacturer’s

instructions and used for normal domestic purposes.

• This guarantee does not cover accidental damage, misuse or alterations which are likely to affect

the product.

• The guarantee is invalid if the product is tampered with, or repaired by any unauthorised person.

(The guarantee in no way affects your statutory or legal right)

What to do if you need to report a problem.

Please ensure you have ready:

• The product’s model and serial numbers.

• Howdens Proof of Purchase Document.

• Your full contact details.

Call the Depot number on your Proof of Purchase

Document supplied with the product / kitchen.

or

Call the LAMONA Service Line on 0344 460 0006

*Product installed within a domestic kitchen or a non-domestic kitchen where 8 or fewer people

are using the appliance.

Where to find the model and serial number on your machine.

Remove grease filter sticker inside the main body.

Page _ 14 www.howdens.com

Product serial number

(Place sticker here)

ISSUE v

4

HD021192