siebert

4 shelf bookcase

style # TGBNT4BKBK (black & walnut) dpci # 249-14-5153 tcin # 53536358 style # TGBNT4BKWH (whitewashed oak & gray) dpci # 249-14-5154 tcin # 53536359

>> assembly instructions

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2

Congratulations on your latest Target purchase.

Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.

All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time. Good luck—though we’re confident you won’t need it.

before you begin

1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.

2. Use the carton as a working surface to prevent product damage during assembly.

3. Read through and review assembly steps.

4. Gather all tools prior to assembly.

tools needed

table of contents

introduction

hardware

parts list

how to use the cam lock system

assembly

5

6

2

4

7-17

QUESTIONS?

Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling. 3

hardware

(H1) x 32 wooden dowel

(H2) x 26 cam bolt

(H3) x 26 cam

(H4) x 32 short pan head screw

(H5) x 1 knob

(H6) x 1 knob bolt

(H7) x 1 wall strap

(H8) x 2 washer

(H9) x 1 wall anchor

(H10) x 1 wall screw

4

(H11) x 1 long pan head screw

(H12) x 6 cam cover

exploded diagram

5

8

9

6

7

10

ITEM DESCRIPTION QUANTITY

1 left side panel 1

2

3

4 right side panel partition shelf A

1

3

1 shelf B shelf C shelf D shelf E door back panel

1

1

1

1

1

2

5

how to use the cam lock system

Screw cam bolt into panel Align cam bolt(s) with cam(s) and insert all the way into cross-bored hole(s)

Push cam into panel - arrow feature on cam top points to panel edge

6

Rotate cam(s) clockwise 180° to lock panels together

Panels should be tight against each other and connection should be rigid

step 1: attach shelf A and B to partition

(H1) x 4 wooden dowel

(H2) x 2 cam bolt

(H3) x 2 cam

1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

1.2. Screw-In cam bolts must be screwed down flush.

1.3. Refer to page 6 for instructions on how to use the cam lock system.

1.4. Do not over tighten bolts.

7

step 2: attach shelf B and C to partition

(H1) x 4 wooden dowel

(H2) x 2 cam bolt

(H3) x 2 cam

8

2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

2.2. Screw-In cam bolts must be screwed down flush.

2.3. Refer to page 6 for instructions on how to use the cam lock system.

2.4. Do not over tighten bolts.

step 3: attach left side panel

x 6 wooden dowel

x 10 cam bolt

3.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

3.2. Screw-In cam bolts must be screwed down flush.

3.3. Refer to page 6 for instructions on how to use the cam lock system.

3.4. Do not over tighten bolts.

9

step 4: attach shelf D and E to partition

(H1) x 4 wooden dowel

(H2) x 2 cam bolt

(H3) x 2 cam

10

4.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

4.2. Screw-In cam bolts must be screwed down flush.

4.3. Refer to page 6 for instructions on how to use the cam lock system.

4.4. Do not over tighten bolts.

step 5: attach shelf D/shelf E/partition to left side panel

(H1) x 4 wooden dowel

(H3) x 4 cam

5.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

5.2. Screw-In cam bolts must be screwed down flush.

5.3. Refer to page 6 for instructions on how to use the cam lock system.

5.4. Do not over tighten bolts.

11

12

step 6: slide in door

step 7: attach right side panel

x 10 wooden dowel

x 10 cam bolt

7.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

7.2. Screw-In cam bolts must be screwed down flush.

7.3. Refer to page 6 for instructions on how to use the cam lock system.

7.4. Do not over tighten bolts.

13

step 8: attach back panel

**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT** hole for anti-tip

Begin by installing all of the screws along one edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square. (If using a tape measure, the distance from one corner, diagonally to the other corner should be the same in both directions.) If not, apply gentle pressure to the diagonally opposite corners to shift case into alignment. Re-measure to ensure equal distances. Install the remaining screws, starting with the corners.

(H4) x 32 short pan head screw pre-drilled holes

14

Make sure the screws go through the pre-drilled holes properly.

8.2. Do not over tighten screws.

step 9: attach door knob

(H5) x 1 knob

(H6) x 1 knob bolt

9.1. Do not over tighten bolts.

15

step 10: attach cam covers

16

(H12) x 6 cam cover

step 11: install anti-tip kit

(H7)

(H11)

(H8)

(H11) screw

x 1 long pan head

(H7) x 1 wall strap

(H9) x 1 wall anchor

(H10) x 1 wall screw

(H8) x 2 washer

Fasten anti-tip strap with wall screw provided

17

WARNING

Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:

• Install tip-over restraint provided.

• Place heaviest items in the lowest drawers.

• Do not set TV's or other heavy objects on top of this product, unless the product is specifically designed to accommodate them.

• Never allow children to climb or hang on drawers, doors, or shelves.

• Never open more than one drawer at a time.

(OR)

• Do not defeat or remove the drawer interlock system.

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

This is a permanent label. Do not remove.

40 lbs.

40 lbs. per shelf

18

1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.

2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.

QUESTIONS?

Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.