VNE Corporation 13MHHM42 1/2 in. Heavy Duty 304L Stainless Steel Clamp Specification
Add to My manuals56 Pages
advertisement
Bio-Pharm Fittings
ASME BPE
Bio-Pharm Hygienic
N E U M O E h r e n b e r g G r o u p
2
Bio-Pharm Fittings
Maximum Purity With Guaranteed Ra
Where cleanability of fittings is the issue, every step in the production process must be carefully controlled.
Our production methods insure that no mechanical damage or flaws occur during manufacturing.
The cleaning procedures incorporate multi-process degreasing and washing steps provided to eliminate any residues of hydrocarbons and stains, using pure deionized water.
Our procedures and process capabilities result in the formation of a stabilized passive layer and increased corrosion resistance.
Our products proudly offer:
Maximum Cleanability
MaxPure fittings are cleaned using a multiple step process to assure clean surface, areas inside and out with repeatability every time.
Every fitting is passivated according to ASME BPE and ASTM A967 standards.
Full Traceability
We provide full traceability for each of our products by supplying all necessary production process data. Starting from certifications and incoming inspection of raw materials, through in-process quality control, final inspection, marking and packaging. The process is also completely documented with a unique job number for each BPE process component.
Every Fitting is Quality Inspected
All around quality and meticulous inspection insures that every fitting will be of the highest quality and in total compliance with all ASME-BPE standards.
MaxPure fittings are 100% visual inspected.
NEUMO Ehrenberg Group
The NEUMO Ehrenberg Group, a diversified multi-national organization headquartered in Germany, was founded by Senator Henry Ehrenberg in 1947.
Over the last decade, the Group has become a leading manufacturer for worldwide Biopharmaceutical process fittings and components. With its three leading companies, NEUMO, VNE and EGMO, the group has developed a worldwide distribution network supporting major Biopharmaceutical multinational accounts.
The Neumo Ehrenberg Group’s synergy and strategy toward the Biopharmaceutical sectors provide customers with innovation, all around quality and efficiency.
Through our Group’s volunteer participation in leading standards organizations, we are actively involved in shaping the future for a cleaner, safer and more productive workplace in the Biopharmaceutical
Processing Industry.
EGMO
NEUMO Ehrenberg Group
Index
Elbows | Page 9-12 | Tees | Page 13-21 | Reducers | Page 22-27 | Use Points | Page 28 |
True Y’s & Laterals | Page 29-30 | Crosses | Page 31-32 | Ferrules | Page 33 |
Solid End Caps & Weld Caps
| Page 34 |
Gaskets | Page 35 | Clamps | Page 36-37 | Adapters | Page 38-39 |
Stub Ends & Slip On Flanges
| Page 39 |
Bio-Pharm Fittings 3
4
Bio-Pharm Fittings
Fittings Specifications
Product:
Stainless Steel fittings comply with ASME BPE standards.
Gaskets are made from compounds which are FDA approved and USP 87, 88 Pharmaceutical Class VI certified.
Sizes:
Stainless Steel fittings are available in sizes ¼” - 6” O.D. tube size.
Material:
Fittings are fabricated in AISI 316L Stainless Steel with sulfur content of 0.005-0.017% achieving superior repeatability for automatic orbital welding process.
Dimensions & Tolerances:
Dimensions as specified in ASME BPE Part DT-3-1
Nominal
Size
O.D.
Wall Thickness
Mechanical Polish (MP)
Wall Thickness
Electropolish (EP)
Squareness
Face to
Tangent, B
Off Angle, 0 in.
mm in.
mm
Equivalent
Angle
(for O)
deg
Off Plane, P
Centerline
Radius
(CLR), R in.
mm in.
mm in.
in.
mm in.
mm in.
mm
1 ⁄
4
± 0.005 ± 0.13 +0.003/-0.004
+0.08/-0.10
+0.003/-0.006
+0.08/-0.15
0.005 0.13 0.009 0.23
2.1
0.030 0.76 0.563
14.30
3 ⁄
8
± 0.005 ± 0.13 +0.003/-0.004
+0.08/-0.10
+0.003/-0.006
+0.08/-0.15
0.005 0.13 0.012
0.3
1.8
0.030 0.76 1.125
28.58
1 ⁄
2
± 0.005 ± 0.13 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.005 0.13 0.014 0.36
1.6
0.030 0.76 1.125
28.58
3
⁄
4
± 0.005 ± 0.13 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.005 0.13 0.018 0.46
1.4
0.030 0.76 1.125
28.58
1 ± 0.005 ± 0.13 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.008 0.20 0.025 0.64
1.4
0.030 0.76 1.500
38.10
1 1 ⁄
2
± 0.008 ± 0.20 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.008 0.20 0.034 0.86
1.3
0.050 1.27 2.250
57.15
2 ± 0.008 ± 0.20 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.008 0.20 0.043 1.09
1.2
0.050 1.27 3.000
76.20
2 1
⁄
2
± 0.010 ± 0.25 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.010 0.25 0.054 1.37
1.2
0.050 1.27 3.750
95.25
3 ± 0.010 ± 0.25 +0.005/-0.008
+0.13/-0.20
+0.005/-0.010
+0.13/-0.25
0.016 0.41 0.068 1.73
1.3
0.050 1.27 4.500 114.30
4
6
± 0.015 ± 0.38 +0.008/-0.010
+0.20/-0.25
+0.008/-0.012
+0.20/-0.30
0.016 0.41 0.086 2.18
± 0.030 ± 0.76 +0.015/-0.015
+0.38/-0.38
+0.015/-0.017
+0.38/-0.43
0.030 0.76 0.135 3.43
1.2
1.3
0.060 1.52 6.000 152.40
0.060 1.52 9.000 228.60
Roundness Wall Thickness
B O P
T
R
C O
E Squareness Face to Tangent Off Angle
Off Plane Height
E
General Notes: a. Tolerance on E end-to-end and center-to-end: 0.050 in.
(1.27 mm) b. Tolerance for centerline radius (CLR) is ±10% of the nominal dimension
EGMO
NEUMO Ehrenberg Group
Fittings Specifications
Surface Finish:
Reference: ASME BPE-2014, Part SF, Table SF-2.4-1.
Inside Surface
Surface
Finish Code
BPE Surface
Designation
Ra Maximum
µ-in.
µm
Surface Condition
PX SF0 No finish requirement
PC
PL
PD
PM
SF1
SF1
SF4
SF4
15
15
20
20
0.51
0.51
0.38
0.38
Mechanically Polished [1]
Mechanically Polished [1]
Mechanically Polished [1] & Electropolished
Mechanically Polished [1] & Electropolished
PR 10 0.25
Mechanically Polished [1] & Electropolished
[1] Or any other finishing method that meets the Ra max.
Outside Surface
Surface Condition
No finish requirement
Light Polish
Mechanically polished to 32 Ra µ-in.
Light Polish
Mechanically polished to 32 Ra µ-in.
Mechanically polished to 32 Ra µ-in.
■ MaxPure fittings guarantee the Ra in all internal surfaces, including bent areas where it is difficult to polish and difficult to measure.
■ All Ra readings are taken across the lay, wherever possible.
■ No single Ra reading shall exceed the Ra max. value in this table.
■ Other Ra readings are available if agreed upon between owner/user and supplier, not to exceed values in this table.
Cleaning:
A multi step cleaning cycle is conducted to ensure that fittings are cleaned with a perfect passivation layer.
The cleaning process involves degreasing, pickling, electro polishing (as required) and passivation. During the final stage, the fittings are double-rinsed using D.I. water.
Inspection Procedures:
All fittings produced by EGMO production are 100% visually inspected for any surface finish imperfections, as mentioned in Table SF-2.2-1, SF-2.2-2, SF-2.4-1 and SF 2.6-1 in the ASME BPE 2014 specification. All dimensional characteristics are inspected for tolerances listed in parts DT-3-1 to DT-9.3-1 in the ASME BPE 2014 specification.
Fitting Marking Information:
Each fitting and process component is permanently laser Marked to show the following: a. Heat number/code traceable to material test report for each product contact surface component b. Material type c. Manufacturer’s name, logo, & trademark d. Product contact surface designation for the appropriate BPE specification e. ASME BPE mark
Packaging & Labeling:
Each fitting is capped, bagged and labeled in full compliance with the ASME BPE standard.
Every label includes a QR Code which directs to the fitting’s Material Test Report (Please refer to page 46).
Documentation:
Full Material Test Reports are supplied with the finished products and are available On-Line at www.MaxPure.net
Bio-Pharm Fittings 5
6
Bio-Pharm Fittings
Electro-Polishing
Why MaxPure EP Bio-Pharm Fittings Lead the Industry
MaxPure EP is EGMO’s line of stainless steel fittings that meet - and exceed - the highly specialized surface finishing requirements of the bio-pharma industry as detailed in the ASME BPE (The American Society of
Mechanical Engineers - Bioprocessing Equipment) guidelines.
The uncompromising high quality of EGMO’s MaxPure EP products is a result of years of experience and accumulated know-how in the electropolishing process during which EGMO has optimized the following four critical elements: a. The temperature of the electrolyte solution.
b. The amplitude of the cathodes and their location relevant to the product.
c. The level of acidity of the solution.
d. The amount of the time that the part is immersed in the solution.
NOTE: The ASME BPE guidelines are very clear, for example, that flash electropolishing, i.e., immersion of the part in the electrolyte solution for a very short period of time, is unacceptable.
Schematic Set-up of EP System
Voltage Control
Cathode
Rack
Piece (Anode)
As a result, MaxPure EP products stand out from competing products in the following ways:
■ A thicker EP layer to minimize rouging
■ Higher Chrome concentration for better corrosion resistance
■ Guaranteed smoothness (Ra) in all internal surfaces to reduce Bio fil m
EP Layer thickness
EP >20Å
ASME BPE >15Å
Reccomendation
Competitor
Flash EP
EGMO
NEUMO Ehrenberg Group
EP Time period
Removal of Contaminants
MaxPure EP removes the contaminants that were introduced by the various production processes. The unique MaxPure EP process achieves a level of contaminant removal that exceeds the ASME BPE standard.
Superior Corrosion Resistance
During the electropolishing process naturally occurring chrome in the product’s base metal is “pulled” to the surface. The thicker the chrome layer that forms on the product surface, the more resistant it will be to corrosion over time. It will also decrease rouging.
The highly optimized MaxPure EP process ensures a particularly thick chrome layer - one of the reasons why MaxPure EP fittings dominate the bio-pharma sector.
Cr
Tube inner surface
Tube inner surface
Cr
Contaminant
Cr
Cr
Cr
Unparalleled Surface Smoothness
The holy grail of surface finishing smoothness is to achieve as low an Ra (Roughness average) value as possible, where Ra is the arithmetic mean of the vertical deviations of the roughness profile from a mean line.
Rougher surfaces create more friction and wear quicker. Surface irregularities are potential sites not only for the formation of cracks and corrosion, but for the build-up of bacteria. Mechanical polishing and buffing, which is the first stage of surface finishing for metals, can achieve good Ra values, but inevitably leave microscopic metal particles and other contaminants on the top surface layer, as well as compounds and foreign matter trapped just below the surface layer.
Before MaxPure EP After MaxPure EP
The MaxPure EP process dramatically improves the mechanically polished surface smoothness.
MaxPure EP Exceeds the ASME BPE Quality Requirements
The table below shows how MaxPure EP exceeds the ASME BPE quality requirements.
✔ The thickness of the electropolish layer, measured in Angstroms.
The thicker the layer, the more contaminant-free and corrosion-resistant the fitting is.
✔ Cr/Fe: The ratio of chrome/iron.
The higher the ratio, the higher the corrosion-resistance.
Attribute
EP layer thickness
CR/Fe ratio
ASME BPE
Recommendation
15Å° <
1 <
EGMO
Electropolishing
20Å° <
1.5 <
Bio-Pharm Fittings 7
Bio-Pharm Fittings
Tube Specifications
Standards:
■ ASTM A-269 / A270-S2
■ ASME BPE
Surface Finish:
Surface finish specifications are the same for fittings & tubes.
Please refer to table SF-2.4-1 page 5.
Tubing Dimensional Tolerances: Tubing specifications, ASTM A-269/A270-S2 inch
1 ⁄
4
”
3 ⁄
8
”
1 ⁄
2
”
3 ⁄
4
”
1”
1 1 ⁄
2
”
2”
2 1 ⁄
2
”
3”
Tubing Diameter mm.
6.35
9.53
4”
12.70
19.05
25.40
38.10
50.80
63.50
76.20
101.60
6” 152.40
0.065
0.065
0.065
0.083
0.109
Wall Thickness inch
0.035
0.035
mm.
0.89
0.89
0.065
0.065
0.065
0.065
1.65
1.65
1.65
1.65
1.65
1.65
1.65
2.11
2.77
OD Tolerance Length
(ASTM Spec.) inch mm.
+/- 0.005
+/- 0.127
+/- 0.005
+/- 0.128
+/- 0.005
+/- 0.129
+/- 0.005
+/- 0.130
+/- 0.005
+/- 0.131
+/- 0.008
+/- 0.203
+/- 0.008
+/- 0.204
+/- 0.010
+/- 0.254
+/- 0.015
+/- 0.381
+/- 0.015
+/- 0.381
+/- 0.030
+/- 0.762
0.125
0.125
0.125
0.188
0.188
0.125
0.125
0.125
0.125
Length
(ASTM Spec.) inch mm.
0.125
3.175
0.125
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
4.763
4.763
Wall Thickness
Tolerance
ASTM Spec.
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
+/- 10%
Ordering Information
To specify the part completely, start with the product description and select the additional options as shown below:
Description 1
TE2S 6L .5
2 Material
Other materials can be supplied upon request
PL
8
1
Size
⁄
4
” , 3
⁄
8
” , 1
⁄
2
”, 3
⁄
4
”, 1”, 1 1
⁄
2
”, 2”, 2 1
⁄
2
”, 3”, 4”, 6”
3 4 Surface Finish (SF)
PX, PC, PL, PM, PD, PR
90° weld ends elbow, ½” size, PL surface finish.
EGMO
NEUMO Ehrenberg Group
Elbows - 45°
1 1
2
⁄
2
2 1
3
⁄
2
3
1
⁄
4
1 ⁄
2
⁄
8
3
1
⁄
4
4
6
TE2KS - 45° ELBOW
Nominal
Size in.
Dimensions
A in.
A mm
2.000
2.000
2.250
2.250
2.250
2.500
3.000
3.375
3.625
92.1
4.500
114.3
6.250
158.8
50.8
50.8
57.2
57.2
57.2
63.5
76.2
85.7
Ordering Code
TE2KS6L.25-..
TE2KS6L.375-..
TE2KS6L.5-..
TE2KS6L.75-..
TE2KS6L1.0-..
TE2KS6L1.5-..
TE2KS6L2.0-..
TE2KS6L2.5-..
TE2KS6L3.0-..
TE2KS6L4.0-..
TE2KS6L6.0-..
TE2KC - 45° ELBOW CLAMP ONE END
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in. B mm
1
3
1
3
⁄
4
2.000 50.8 1.000 25.4 TE2KC6L.25-..
⁄
8
2.000 50.8 1.000 25.4 TE2KC6L.375-..
⁄
2
2.250 57.2 1.000 25.4 TE2KC6L.5-..
⁄
4
2.250 57.2 1.000 25.4 TE2KC6L.75-..
* 1
1 1
2.250 57.2 1.125 28.6 TE2KC6L1.0-..
⁄
2
2.500 63.5 1.438 36.5 TE2KC6L1.5-..
2 3.000 76.2 1.750 44.5 TE2KC6L2.0-..
2 1
3
⁄
2
3.375 85.7 2.063 52.4 TE2KC6L2.5-..
3.625 92.1 2.375 60.3 TE2KC6L3.0-..
4
6
4.500 114.3 3.125 79.4 TE2KC6L4.0-..
6.250 158.8 5.250 133.4 TE2KC6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
TEG2K - 45° ELBOW
Nominal
Size in.
Dimensions Ordering Code
* 1
1 1
A in. A mm
3
1 ⁄
4
1.000 25.4
3
1 ⁄
2
⁄
8
1.000 25.4
1.000 25.4
⁄
4
1.000 25.4
1.125 28.6
2
⁄
2
1.438 36.5
1.750 44.5
2 1
3
⁄
2
2.063 52.4
2.375 60.3
4
6
3.125 79.4
5.250 133.4
TEG2K6L.25-..
TEG2K6L.375-..
TEG2K6L.5-..
TEG2K6L.75-..
TEG2K6L1.0-..
TEG2K6L1.5-..
TEG2K6L2.0-..
TEG2K6L2.5-..
TEG2K6L3.0-..
TEG2K6L4.0-..
TEG2K6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
A
BPE TABLE # DT-4.1.1-4
B
A
BPE TABLE # DT-4.1.1-5
A
A
BPE TABLE # DT-4.1.1-6
Bio-Pharm Fittings 9
A
88 ◦
A
T
A
88 ◦
A
A
88 ◦
A
T
10
Bio-Pharm Fittings
Elbows - 88°
A
88 ◦
A
T
A
88 ◦
B
T
A
88 ◦
A
TE2S - 88° ELBOW
Nominal
Size in.
Dimensions Ordering Code
T α=88° in.
mm A in. A mm
1
3
1
⁄
2
0.65
1.65
3.06
77.7 TE2S886L.5-..
⁄
4
0.65
1.65
3.06
77.7 TE2S886L.75-..
0.65
1.65
3.05
A
88 ◦
77.5 TE2S886L1.0-..
1 1
2
⁄
2
0.65
1.65
3.80
96.5 TE2S886L1.5-..
0.65
1.65
4.81
122.2 TE2S886L2.0-..
2 1
3
⁄
2
0.65
1.65
5.56
141.2 TE2S886L2.5-..
0.65
1.65
6.31
160.3 TE2S886L3.0-..
4 0.83
2.11
8.07
205.0 TE2S886L4.0-..
TE2C - 88° ELBOW
Nominal
Size in.
Dimensions Ordering Code
T α=88° in. mm A in. A mm B in. B mm
1
3
⁄
2
0.65 1.65 3.01 76.50 1.71 43.50 TE2C886L.5-..
⁄
4
0.65 1.65 3.01 76.50 1.71 43.50 TE2C886L.75-..
* 1 0.65 1.65 3.01 76.50 2.04 51.80 TE2C886L1.0-..
1 1 ⁄
2
0.65 1.65 3.76 95.60 2.79 70.75 TE2C886L1.5-..
2 0.65 1.65 4.73 120.10 3.62 92.00 TE2C886L2.0-..
2 1 ⁄
2
0.65 1.65 5.51 140.00 4.22 107.25 TE2C886L2.5-..
3 0.65 1.65 6.27 159.20 4.94 125.40 TE2C886L3.0-..
4 0.83 2.11 8.02 203.75 6.42 163.10 TE2C886L4.0-..
Note: 89 ° & 91 ° elbows are available upon request.
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
88 ◦
A
A
88 ◦
B
T
TEG2C - 88° ELBOW
Nominal
Size in.
Dimensions
T α=88°
Ordering Code
1
3 in.
mm A in. A mm
⁄
2
0.65
1.65
1.63
41.3 TEG2C886L.5-..
⁄
4
0.65
1.65
1.63
41.3 TEG2C886L.75-..
* 1 0.65
1.65
2.01
51.1 TEG2C886L1.0-..
1 1
2
⁄
2
0.65
1.65
2.76
70.2 TEG2C886L1.5-..
0.65
1.65
3.51
89.2 TEG2C886L2.0-..
2 1
3
⁄
2
0.65
1.65
4.26
108.3 TEG2C886L2.5-..
0.65
1.65
5.01
127.3 TEG2C886L3.0-..
4 0.83
2.11
6.65
168.8 TEG2C886L4.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
EGMO
NEUMO Ehrenberg Group
Elbows - 90°
1 1
2
⁄
2
2 1
3
⁄
2
3
1
⁄
4
1 ⁄
2
⁄
8
3
1
⁄
4
4
6
TE2S - 90° ELBOW
Nominal
Size in.
Dimensions
A in.
A mm
2.625
66.7
2.625
66.7
3.000
3.000
76.2
76.2
3.000
3.750
76.2
95.3
4.750
120.7
5.500
139.7
6.250
158.8
8.000
203.2
11.500
292.1
Ordering Code
TE2S6L.25-..
TE2S6L.375-..
TE2S6L.5-..
TE2S6L.75-..
TE2S6L1.0-..
TE2S6L1.5-..
TE2S6L2.0-..
TE2S6L2.5-..
TE2S6L3.0-..
TE2S6L4.0-..
TE2S6L6.0-..
TE2C - 90° ELBOW CLAMP ONE END
Nominal
Size in.
Dimensions
Ordering
Code
1
3
1
3
A in. A mm B in. B mm
⁄
4
2.625 66.7 1.625 41.3 TE2C6L.25-..
⁄
8
2.625 66.7 1.625 41.3 TE2C6L.375-..
⁄
2
3.000 76.2 1.625 41.3 TE2C6L.5-..
⁄
4
3.000 76.2 1.625 41.3 TE2C6L.75-..
* 1
1 1
3.000 76.2 2.000 50.8 TE2C6L1.0-..
⁄
2
3.750 95.3 2.750 69.9 TE2C6L1.5-..
2 1
2 4.750 120.7 3.500 88.9 TE2C6L2.0-..
⁄
2
5.500 139.7 4.250 108.0 TE2C6L2.5-..
3 6.250 158.8 5.000 127.0 TE2C6L3.0-..
4 8.000 203.2 6.625 168.3 TE2C6L4.0-..
6 11.500 292.1 10.500 266.7 TE2C6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
TEG2C - 90° ELBOW
Nominal
Size in.
Dimensions Ordering Code
3
A in. A mm
1
⁄
4
1.625 41.3
3
1 ⁄
2
⁄
8
1.625 41.3
1.625 41.3
* 1
1 1
2.000 50.8
⁄
2
2.750 69.9
2
⁄
4
1.625 41.3
3.500 88.9
2 1
3
⁄
2
4.250 108.0
5.000 127.0
TEG2C6L.25-..
TEG2C6L.375-..
TEG2C6L.5-..
TEG2C6L.75-..
TEG2C6L1.0-..
TEG2C6L1.5-..
TEG2C6L2.0-..
TEG2C6L2.5-..
TEG2C6L3.0-..
TEG2C6L4.0-..
4 6.625 168.3
6 10.500 266.7
TEG2C6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
BPE TABLE # DT-4.1.1-1
BPE TABLE # DT-4.1.1-2
BPE TABLE # DT-4.1.1-3
Bio-Pharm Fittings 11
A
92 ◦
T
A
A
92 ◦
A
A
92 ◦
T
A
12
Bio-Pharm Fittings
Elbows - 92°
A
92 ◦
T
A
A
92 ◦
T
B
A
92 ◦
A
A
92 ◦
TE2S - 92° ELBOW
Nominal
Size in.
Dimensions Ordering Code
T α=92°
3
A
1 1
2
1 ⁄
2 in.
0.65
mm A in. A mm
1.65
2.93
74.4 TE2S926L.5-..
1
⁄
⁄
4
0.65
1.65
2.93
74.4 TE2S926L.75-..
2
0.65
1.65
0.65
1.65
0.65
1.65
2.95
3.69
74.9 TE2S926L1.0-..
93.7 TE2S926L1.5-..
4.69
119.1 TE2S926L2.0-..
2 1
3
⁄
2
0.65
1.65
5.44
138.2 TE2S926L2.5-..
0.65
1.65
6.19
157.2 TE2S926L3.0-..
4 0.83
2.115
7.93
201.4 TE2S926L4.0-..
TE2C - 92° ELBOW
Nominal
Size in.
Dimensions Ordering Code
T α=92° in.
mm A in. A mm B in. B mm
1
3
⁄
2
0.65 1.65
2.98
75.7 1.66
42.1 TE2C926L.5-..
⁄
4
0.65 1.65
2.98
75.7 1.66
42.1 TE2C926L.75-..
* 1 0.65 1.65
2.98
75.7 2.05
52.1 TE2C926L1.0-..
1 1 ⁄
2
0.65 1.65
3.73
94.8 2.73
69.3 TE2C926L1.5-..
2 0.65 1.65
4.77 121.2 3.47
88.2 TE2C926L2.0-..
2 1 ⁄
2
0.65 1.65
5.43 137.8 4.10 104.2 TE2C926L2.5-..
3 0.65 1.65
6.17 156.8 4.83 122.8 TE2C926L3.0-..
4 0.83 2.115 7.91 200.8 6.42 163.0 TE2C926L4.0-..
Note: 89 ° & 91 ° elbows are available upon request.
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
TEG2C - 92° ELBOW
Nominal
Size in.
Dimensions Ordering Code
92 ◦
T α=92°
T
B in.
mm A in. A mm
1
3
⁄
2
0.65
1.65
1.61
40.8 TEG2C926L.5-..
⁄
4
0.65
1.65
1.61
40.8 TEG2C926L.75-..
* 1 0.65
1.65
1.99
50.5 TEG2C926L1.0-..
1 1
2
⁄
2
0.65
1.65
2.74
69.6 TEG2C926L1.5-..
0.65
1.65
3.49
88.6 TEG2C926L2.0-..
2 1
3
⁄
2
0.65
1.65
4.04
102.6 TEG2C926L2.5-..
0.65
1.65
4.76
120.8 TEG2C926L3.0-..
4 0.83
2.115
6.30
160.0 TEG2C926L4.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
EGMO
NEUMO Ehrenberg Group
Tees - Equal
TE7WWW - TEE
Nominal
Size in.
Dimensions
A in.
1.750
A mm
44.5
1 1 ⁄
2
2
2 1 ⁄
2
3
4
6
1 ⁄
4
3
1
⁄
2
⁄
8
3 ⁄
4
1
1.750
1.875
2.000
2.125
2.375
2.875
3.125
3.375
4.125
5.625
44.5
47.6
50.8
54.0
60.3
73.0
79.4
85.7
104.8
142.9
Ordering Code
TE7WWW6L.25-..
TE7WWW6L.375-..
TE7WWW6L.5-..
TE7WWW6L.75-..
TE7WWW6L1.0-..
TE7WWW6L1.5-..
TE7W WW6L2.0-..
TE7WWW6L2.5-..
TE7WWW6L3.0-..
TE7WWW6L4.0-..
TE7WWW6L6.0-..
TE7WWC - TEE
Nominal
Size in.
Dimensions Ordering Code
3
1
⁄
2
⁄
4
A in. A mm B in. B mm C in. C mm
1.875 47.6 2.250 57.20 3.750 95.2 TE7WWC6L.5-..
2.000 50.8 2.375 60.30 4.000 101.6 TE7WWC6L.75-..
* 1
1 1
2.125 54.0 2.625 66.68 4.250 108.0 TE7WWC6L1.0-..
⁄
2
2.375 60.3 2.875 73.03 4.750 120.6 TE7WWC6L1.5-..
2 1
2 2.875 73.0 3.375 85.70 5.750 146.0 TE7WWC6L2.0-..
⁄
2
3.125 79.4 3.625 92.08 6.250 158.8 TE7WWC6L2.5-..
3 3.375 85.7 3.875 98.43 6.750 171.4 TE7WWC6L3.0-..
4 4.125 104.8 4.750 120.65 8.250 209.6 TE7WWC6L4.0-..
6 5.625 142.9 7.125 181.0 11.250 285.8 TE7WWC6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
TEG7 - TEE
Nominal Size in.
Dimensions Ordering Code
3
3
* 1
⁄
4
1
1
⁄
2
⁄
4
⁄
8
1 1
2
⁄
2
2 1
3
⁄
2
4
6
A in.
2.250
2.250
2.250
2.375
2.625
2.875
3.375
3.625
3.875
4.750
7.125
A mm
57.2
57.2
57.2
60.3
66.7
73.0
85.7
92.1
98.4
120.7
181.0
TEG76L.25-..
TEG76L.375-..
TEG76L.5-..
TEG76L.75-..
TEG76L1.0-..
TEG76L1.5-..
TEG76L2.0-..
TEG76L2.5-..
TEG76L3.0-..
TEG76L4.0-..
TEG76L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
A A
A
BPE TABLE # DT-4.1.2-1
A A
A
A A
C
C C
B
B B
A
A A
BPE TABLE # DT-4.1.2-4
A
A A
Bio-Pharm Fittings 13
Bio-Pharm Fittings
Tees - 88°
A
A
88 o
TE7WWW886L - BRANCH TEE 88°
Nominal
Size in.
Dimensions Ordering Code
A in.
A mm
1 1
1
⁄
2
2
2 1
3
⁄
2
4
2.125
2.375
2.875
3.125
3.375
4.125
54
60.3
73
79.4
85.7
104.8
TE7WWW886L1.0-..
TE7WWW886L1.5-..
TE7WWW886L2.0-..
TE7WWW886L2.5-..
TE7WWW886L3.0-..
TE7WWW886L4.0-..
Note: Reducing sizes and special end configurations can be supplied upon request.
TEES - 176°
A
B
88 o 88
B o
TE7WWW1766L - 176° RUN TEE
Nominal
Size in.
Dimensions Ordering Code
1
1 1
2
⁄
2
2 1
3
⁄
2
4
A in. A mm B in.
B mm
2.2
55.88
2.12
53.848 TE7WWW1766L1.0-..
2.46
62.484
2.37
60.198 TE7WWW1766L1.5-..
2.98
75.692
2.87
72.898 TE7WWW1766L2.0-..
3.24
82.296
3.12
79.248 TE7WWW1766L2.5-..
3.5
88.9
3.73
94.742 TE7WWW1766L3.0-..
4.27 108.458 4.12 104.648 TE7WWW1766L4.0-..
Note: Reducing sizes and special end configurations can be supplied upon request.
14
EGMO
NEUMO Ehrenberg Group
A
B
Tees - Short Outlet
TE7WWCS - SHORT OUTLET TEE
Nominal
Size in.
Dimensions Ordering Code
1
3
1
3
* 1
1 1
A in. A mm B in. B mm
⁄
4
1.750 44.5 1.000 25.4
⁄
8
1.750 44.5 1.000 25.4
⁄
2
1.875 47.6 1.000 25.4
⁄
4
2.000 50.8 1.125 28.6
2.125 54.0 1.125 28.6
2
⁄
2
2.375 60.3 1.375 34.9
2.875 73.0 1.625 41.3
2 1
3
⁄
2
3.125 79.4 1.875 47.6
3.375 85.7 2.125 54.0
TE7WWCS6L.25-..
TE7WWCS6L.375-..
TE7WWCS6L.5-..
TE7WWCS6L.75-..
TE7WWCS6L1.0-..
TE7WWCS6L1.5-..
TE7WWCS6L2.0-..
TE7WWCS6L2.5-..
TE7WWCS6L3.0-..
TE7WWCS6L4.0-..
4 4.125 104.8 2.750 69.9
6 5.625 142.9 4.625 117.5
TE7WWCS6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
TE7WCSW - SHORT OUTLET RUN TEE
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in. B mm C in. C mm
3
1
⁄
8
⁄
4
3
1
* 1
⁄
4
⁄
2
0.875 22.2 1.750 44.5 1.750 44.5 TE7WCSW6L.25-..
0.875 22.2 1.750 44.5 1.750 44.5 TE7WCSW6L.375-..
0.875 22.2 1.875 47.6 1.875 47.6 TE7WCSW6L.5-..
1.000 25.4 2.000 50.8 2.000 50.8 TE7WCSW6L.75-..
1.125 28.6 2.125 54.0 2.125 54.0 TE7WCSW6L1.0-..
1 1
2
⁄
2
1.375 34.9 2.375 60.3 2.375 60.3 TE7WCSW6L1.5-..
1.625 41.3 2.875 73.0 2.875 73.0 TE7WCSW6L2.0-..
2 1
3
⁄
2
1.875 47.6 3.125 79.4 3.125 79.4 TE7WCSW6L2.5-..
2.125 54.0 3.375 85.7 3.375 85.7 TE7WCSW6L3.0-..
4
6
2.750 69.9 4.125 104.8 4.125 104.8 TE7WCSW6L4.0-..
4.625 117.5 5.625 142.9 5.625 142.9 TE7WCSW6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
TEG7S - SHORT OUTLET TEE
Nominal
Size in.
Dimensions
1 ⁄
2
3 ⁄
4
* 1
A in. A mm B in. B mm
2.250 57.2 1.000 25.4
2.375 60.3 1.125 28.6
2.625 66.7 1.125 28.6
1 1 ⁄
2
2.875 73.0 1.375 34.9
2 3.375 85.7 1.625 41.3
2 1
⁄
2
3.625 92.1 1.875 47.6
Ordering Code
TEG7S6L.5-..
TEG7S6L.75-..
TEG7S6L1.0-..
TEG7S6L1.5-..
TEG7S6L2.0-..
TEG7S6L2.5-..
3
4
3.875 98.4 2.125 54.0
4.750 120.7 2.750 69.9
TEG7S6L3.0-..
TEG7S6L4.0-..
6 7.125 181.0 4.625 117.5
TEG7S6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
B
B
A
B
A
A
BPE TABLE # DT-4.1.2-3
B
B A A
BPE TABLE # DT-4.1.2-5
B
C
Bio-Pharm Fittings 15
C
B A
Bio-Pharm Fittings
Tees - Reducing
B
A
BPE TABLE # DT-4.1.2-6
TE7RWWW - REDUCING TEE
Nominal Size in.
Dimensions Ordering Code
3 x 1 1
3 x 2
⁄
2
3 x 2
4 x 1
4 x 3
1
⁄
2
⁄
2
⁄
4
4 x 1
4 x 1 1
⁄
2
4 x 2
4 x 2 1
4 x 3
⁄
2
A in. A mm B in. B mm
3
1
1
⁄
8
x 1 ⁄
4
⁄
2
x 1
⁄
4
⁄
2
x 3
⁄
8
3
3
3
⁄
4
x 1 ⁄
4
⁄
4
x 3 ⁄
8
⁄
4
x 1 ⁄
2
1 x 1 ⁄
4
1 x
1 x 1
3
⁄
2
⁄
8
1
1 x
1
3 ⁄
4
⁄
2
x 1 ⁄
2
1 1
1 1
⁄
2
x 3 ⁄
4
⁄
2
x 1
2 x 1
2 x 3
⁄
2
⁄
4
1.750 44.5 1.750 44.5 TE7RWWW6L.375x.25-..
1.875 47.6 1.875 47.6 TE7RWWW6L.5x.25-..
1.875 47.6 1.875 47.6 TE7RWWW6L.5x.375-..
2.000 50.8 2.000 50.8 TE7RWWW6L.75x.25-..
2.000 50.8 2.000 50.8 TE7RWWW6L.75x.375-..
2.000 50.8 2.000 50.8 TE7RWWW6L.75x.5-..
2.125 54.0 2.125 54.0 TE7RWWW6L1.0x.25-..
2.125 54.0 2.125 54.0 TE7RWWW6L1.0x.375-..
2.125 54.0 2.125 54.0 TE7RWWW6L1.0x.5-..
2.125 54.0 2.125 54.0 TE7RWWW6L1.0x.75-..
2.375 60.3 2.375 60.3 TE7RWWW6L1.5x.5-..
2.375 60.3 2.375 60.3 TE7RWWW6L1.5x.75-..
2.375 60.3 2.375 60.3 TE7RWWW6L1.5x1.0-..
2.875 73.0 2.625 66.7 TE7RWWW6L2.0x.5-..
2.875 73.0 2.625 66.7 TE7RWWW6L2.0x.75-..
2 x 1
2
2 x 1 1
1
⁄
2
⁄
2
x 1
⁄
2
2.875 73.0 2.625 66.7 TE7RWWW6L2.0x1.0-..
2.875 73.0 2.625 66.7 TE7RWWW6L2.0x1.5-..
3.125 79.4 2.875 73.0 TE7RWWW6L2.5x.5-..
2 1
2 1
⁄
2
x 3 ⁄
4
⁄
2
x 1
3.125 79.4 2.875 73.0 TE7RWWW6L2.5x.75-..
3.125 79.4 2.875 73.0 TE7RWWW6L2.5x1.0-..
2 1
2 1
⁄
2
x 1 1 ⁄
2
3.125 79.4 2.875 73.0 TE7RWWW6L2.5x1.5-..
⁄
2
x 2 3.125 79.4 2.875 73.0 TE7RWWW6L2.5x2.0-..
3 x 1
3 x 3
⁄
2
⁄
4
3.375 85.7 3.125 79.4 TE7RWWW6L3.0x.5-..
3.375 85.7 3.125 79.4 TE7RWWW6L3.0x.75-..
3 x 1 3.375 85.7 3.125 79.4 TE7RWWW6L3.0x1.0-..
3.375 85.7 3.125 79.4 TE7RWWW6L3.0x1.5-..
3.375 85.7 3.125 79.4 TE7RWWW6L3.0x2.0-..
3.375 85.7 3.125 79.4 TE7RWWW6L3.0x2.5-..
4.125 104.8 3.625 92.1 TE7RWWW6L4.0x.5-..
4.125 104.8 3.625 92.1 TE7RWWW6L4.0x.75-..
4.125 104.8 3.625 92.1 TE7RWWW6L4.0x1.0-..
4.125 104.8 3.625 92.1 TE7RWWW6L4.0x1.5-..
4.125 104.8 3.875 98.4 TE7RWWW6L4.0x2.0-..
4.125 104.8 3.875 98.4 TE7RWWW6L4.0x2.5-..
4.125 104.8 3.875 98.4 TE7RWWW6L4.0x3.0-..
6 x 3
6 x 4
5.625 142.9 4.875 123.8 TE7RWWW6L6.0x3.0-..
5.625 142.9 5.125 130.2 TE7RWWW6L6.0x4.0-..
16
EGMO
NEUMO Ehrenberg Group
Tees - Reducing
TE7RWWC - REDUCING TEE
Nominal Size in.
Dimensions Ordering Code
A in. A mm B in. B mm
3 ⁄
4
x 1 ⁄
2
* 1 x 1 ⁄
2
1
* 1 x
1
3 ⁄
4
⁄
2
x 1 ⁄
2
1
1 1
1 ⁄
2
x 3 ⁄
4
⁄
2
x 1 *
2 x 1 ⁄
2
2 x 3 ⁄
4
2 x 1 *
2.000 50.8 2.500 63.5 TE7RWWC6L.75x.5-..
2.125 54.0 2.625 66.7 TE7RWWC6L1.0x.5-..
2.125 54.0 2.625 66.7 TE7RWWC6L1.0x.75-..
2.375 60.3 2.875 73.0 TE7RWWC6L1.5x.5-..
2.375 60.3 2.875 73.0 TE7RWWC6L1.5x.75-..
2.375 60.3 2.875 73.0 TE7RWWC6L1.5x1.0-..
2.875 73.0 3.125 79.4 TE7RWWC6L2.0x.5-..
2.875 73.0 3.125 79.4 TE7RWWC6L2.0x.75-..
2.875 73.0 3.125 79.4 TE7RWWC6L2.0x1.0-..
2
2
2 x 1 1
1
⁄
2
⁄
2
x 1 ⁄
2
1
2.875 73.0 3.125 79.4 TE7RWWC6L2.0x1.5-..
3.125 79.4 3.375 85.7 TE7RWWC6L2.5x.5-..
2 1
⁄
2
x 1 1 ⁄
2
3.125 79.4 3.375 85.7 TE7RWWC6L2.5x1.5-..
⁄
2
x 2 3.125 79.4 3.375 85.7 TE7RWWC6L2.5x2.0-..
3 x 1 * 3.375 85.7 3.625 92.1 TE7RWWC6L3.0x1.0-..
3 x 1 1
3 x 2
⁄
2
3 x 2 1
4 x 1 *
⁄
2
4 x 1 1
4 x 2
⁄
2
4 x 2 1
4 x 3
⁄
2
3.375 85.7 3.625 92.1 TE7RWWC6L3.0x1.5-..
3.375 85.7 3.625 92.1 TE7RWWC6L3.0x2.0-..
3.375 85.7 3.625 92.1 TE7RWWC6L3.0x2.5-..
4.125 104.8 4.125 104.8 TE7RWWC6L4.0x1.0-..
4.125 104.8 4.125 104.8 TE7RWWC6L4.0x1.5-..
4.125 104.8 4.375 111.1 TE7RWWC6L4.0x2.0-..
4.125 104.8 4.375 111.1 TE7RWWC6L4.0x2.5-..
4.125 104.8 4.375 111.1 TE7RWWC6L4.0x3.0-..
6 x 3
6 x 4
5.625 142.9 5.375 136.5 TE7RWWC6L6.0x3.0-..
5.625 142.9 5.750 146.1 TE7RWWC6L6.0x4.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
B
Bio-Pharm Fittings 17
18
Bio-Pharm Fittings
Tees - Reducing
A
BPE TABLE # DT-4.1.2-7
B
TE7RWWCS-SHORT OUTLET REDUCING TEE
Nominal Size in.
Dimensions Ordering Code
4 x 1 1
4 x 2
⁄
2
4 x 2 1
4 x 3
⁄
2
6 x 1
6 x 3
⁄
2
⁄
4
6 x 1 *
6 x 1 1
6 x 2
⁄
2
6 x 2 1
6 x 3
⁄
2
A in. A mm B in. B mm
3
1
3
1
⁄
8
x 1 ⁄
4
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
⁄
4
x 1 ⁄
4
3
3
⁄
4
x 3 ⁄
8
⁄
4
x 1 ⁄
2
1 x 1 ⁄
4
⁄
8
1
1
1 x 3
1 x 1
1
1
1 x 3
⁄
2
⁄
4
⁄
2
x 1 ⁄
2
⁄
2
x 3 ⁄
4
1 1 ⁄
2
x 1 *
2 x 1 ⁄
2
2 x 3 ⁄
4
2 x 1 *
1.750 44.5 1.000 25.4 TE7RWWCS6L.375x.25-..
1.875 47.6 1.000 25.4 TE7RWWCS6L.5x.25-..
1.875 47.6 1.000 25.4 TE7RWWCS6L.5x.375-..
2.000 50.8 1.000 25.4 TE7RWWCS6L.75x.25-..
2.000 50.8 1.000 25.4 TE7RWWCS6L.75x.375-..
2.000 50.8 1.000 25.4 TE7RWWCS6L.75x.5-..
2.125 54.0 1.125 28.6 TE7RWWCS6L1.0x.5-..
2.125 54.0 1.125 28.6 TE7RWWCS6L1.0x0.375
2.125 54.0 1.125 28.6 TE7RWWCS6L1.0x.5-..
2.125 54.0 1.125 28.6 TE7RWWCS6L1.0x.75-..
2.375 60.3 1.375 34.9 TE7RWWCS6L1.5x.5-..
2.375 60.3 1.375 34.9 TE7RWWCS6L1.5x.75-..
2.375 60.3 1.375 34.9 TE7RWWCS6L1.5x1.0-..
2.875 73.0 1.625 41.3 TE7RWWCS6L2.0x.5-..
2.875 73.0 1.625 41.3 TE7RWWCS6L2.0x.75-..
2.875 73.0 1.625 41.3 TE7RWWCS6L2.0x1.0-..
2
2 x 1 1
1
⁄
2
⁄
2
x 1 ⁄
2
2
2 1
1 ⁄
2
x 3 ⁄
4
⁄
2
x 1 *
2.875 73.0 1.625 41.3 TE7RWWCS6L2.0x1.5-..
3.125 79.4 1.875 47.6 TE7RWWCS6L2.5x.5-..
3.125 79.4 1.875 47.6 TE7RWWCS6L2.5x.75-..
3.125 79.4 1.875 47.6 TE7RWWCS6L2.5x1.0-..
2 1
2 1
⁄
2
x 1 1 ⁄
2
3.125 79.4 1.875 47.6 TE7RWWCS6L2.5x1.5-..
⁄
2
x 2 3.125 79.4 1.875 47.6 TE7RWWCS6L2.5x2.0-..
3 x 1
3 x 3
⁄
2
⁄
4
3 x 1 *
3.375 85.7 2.125 54.0 TE7RWWCS6L4.0x.5-..
3.375 85.7 2.125 54.0 TE7RWWCS6L4.0x.75-..
3.375 85.7 2.125 54.0 TE7RWWCS6L3.0x1.0-..
3 x 1 1
3 x 2
⁄
2
3 x 2 1
4 x 1
4 x 3 ⁄
4
4 x 1 *
⁄
2
⁄
2
3.375 85.7 2.125 54.0 TE7RWWCS6L3.0x1.5-..
3.375 85.7 2.125 54.0 TE7RWWCS6L3.0x2.0-..
3.375 85.7 2.125 54.0 TE7RWWCS6L3.0x2.5-..
4.125 104.8 2.625 66.7 TE7RWWCS6L3.0x.5-..
4.125 104.8 2.625 66.7 TE7RWWCS6L3.0x.75-..
4.125 104.8 2.625 66.7 TE7RWWCS6L4.0x1.0-..
4.125 104.8 2.625 66.7 TE7RWWCS6L4.0x1.5-..
4.125 104.8 2.625 66.7 TE7RWWCS6L4.0x2.0-..
4.125 104.8 2.625 66.7 TE7RWWCS6L4.0x2.5-..
4.125 104.8 2.625 66.7 TE7RWWCS6L4.0x3.0-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x.5-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x.75-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x1.0-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x1.5-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x2.0-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x2.5-..
5.625 142.9 3.625 92.1 TE7RWWCS6L6.0x3.0-..
6 x 4 5.625 142.9 3.750 95.3 TE7RWWCS6L6.0x4.0-..
Note: Additional sizes are available upon request.
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
EGMO
NEUMO Ehrenberg Group
Tees - Reducing
TEG7R - REDUCING TEE
Nominal Size in.
Dimensions Ordering Code
3 x 1 1
3 x 2
⁄
2
3 x 2 1
4 x 1
4 x 3 ⁄
4
4 x 1 *
⁄
2
⁄
2
4 x 1 1
4 x 2
⁄
2
4 x 2 1
4 x 3
⁄
2
A in. A mm B in. B mm
3
1
1
3
⁄
8
x 1 ⁄
4
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
⁄
4
x 1 ⁄
4
3
3
⁄
4
x 3 ⁄
8
⁄
4
x 1 ⁄
2
* 1 x 1 ⁄
4
⁄
8
* 1 x 3
* 1 x 1
* 1 x 3
1 1 ⁄
2
x 1 ⁄
2
⁄
2
x 3 ⁄
4
⁄
2
⁄
4
1 1
1 1 ⁄
2
x 1 *
2 x 1 ⁄
2
2 x 3 ⁄
4
2 x 1 *
2.250 57.2 2.250 57.2
2.375 60.3 2.375 60.3
2.375 60.3 2.375 60.3
2.500 63.5 2.500 63.5
2.500 63.5 2.500 63.5
2.500 63.5 2.500 63.5
2.625 66.7 2.625 66.7
2.625 66.7 2.625 66.7
2.625 66.7 2.625 66.7
2.625 66.7 2.625 66.7
2.875 73.0 2.875 73.0
2.875 73.0 2.875 73.0
2.875 73.0 2.875 73.0
3.375 85.7 3.125 79.4
3.375 85.7 3.125 79.4
3.375 85.7 3.125 79.4
TEG7R6L.375x.25-..
TEG7R6L.5x.25-..
TEG7R6L.5x.375-..
TEG7R6L.75x.25-..
TEG7R6L.75x.375-..
TEG7R6L.75x.5-..
TEG7R6L1.0x.25-..
TEG7R6L1.0x.375-..
TEG7R6L1.0X.5-..
TEG7R6L1.0x.75-..
TEG7R6L1.5X.5-..
TEG7R6L1.5x.75-..
TEG7R6L1.5X1.0-..
TEG7R6L2.0X.5-..
TEG7R6L2.0x.75-..
TEG7R6L2.0X1.0-..
2
2 x 1 1
2 1
2 1
1
⁄
2
x 1
⁄
2
⁄
⁄
2
x 3 ⁄
4
⁄
2
x 1 *
2
2 1
2 1
3 x 1
3 x 3
⁄
2
⁄
4
3 x 1 *
3.375 85.7 3.125 79.4
3.625 92.1 3.375 85.7
3.625 92.1 3.375 85.7
3.625 92.1 3.375 85.7
TEG7R6L2.0X1.5-..
TEG7R6L2.5X.5-..
TEG7R6L2.5x.75-..
TEG7R6L2.5X1.0-..
⁄
2
x 1 1 ⁄
2
3.625 92.1 3.375 85.7
TEG7R6L2.5X1.5-..
⁄
2
x 2 3.625 92.1 3.375 85.7
TEG7R6L2.5X2.0-..
3.875 98.4 3.625 92.1
3.875 98.4 3.625 92.1
3.875 98.4 3.625 92.1
TEG7R6L3.0X.5-..
TEG7R6L3.0x.75-..
TEG7R6L3.0X1.0-..
3.875 98.4 3.625 92.1
3.875 98.4 3.625 92.1
3.875 98.4 3.625 92.1
4.750 120.7 4.125 104.8
4.750 120.7 4.125 104.8
4.750 120.7 4.125 104.8
4.750 120.7 4.125 104.8
4.750 120.7 4.375 111.1
4.750 120.7 4.375 111.1
4.750 120.7 4.375 111.1
TEG7R6L3.0X1.5-..
TEG7R6L3.0X2.0-..
TEG7R6L3.0X2.5-..
TEG7R6L4.0X.5-..
TEG7R6L4.0x.75-..
TEG7R6L4.0X1.0-..
TEG7R6L4.0X1.5-..
TEG7R6L4.0X2.0-..
TEG7R6L4.0X2.5-..
TEG7R6L4.0X3.0-..
6 x 3
6 x 4
7.125 181.0 5.375 136.5
7.125 181.0 5.750 146.1
TEG7R6L6.0X3.0-..
TEG7R6L6.0X4.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
BPE TABLE # DT-4.1.2-8
B
Bio-Pharm Fittings 19
20
Bio-Pharm Fittings
Tees - Reducing
A
BPE TABLE # DT-4.1.2-9
B
EGMO
NEUMO Ehrenberg Group
TEG7RS-SHORT OUTLET REDUCING TEE
Nominal Size in.
Dimensions Ordering Code
4 x 1 1
4 x 2
⁄
2
4 x 2 1
4 x 3
⁄
2
6 x 1
6 x 3
⁄
2
⁄
4
6 x 1 *
6 x 1 1
6 x 2
⁄
2
6 x 2 1
6 x 3
⁄
2
A in. A mm B in. B mm
3
1
1
3
⁄
8
x 1 ⁄
4
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
⁄
4
x 1 ⁄
4
3
3
⁄
4
x 3 ⁄
8
⁄
4
x 1 ⁄
2
* 1 x 1 ⁄
4
⁄
8
* 1 x 3
* 1 x 1
* 1 x 3
1 1 ⁄
2
x 1 ⁄
2
⁄
2
x 3 ⁄
4
⁄
2
⁄
4
1 1
1 1 ⁄
2 x 1 *
2 x 1 ⁄
2
2 x 3 ⁄
4
2 x 1 *
2.250 57.2 1.000 25.4 TEG7RS6L.375x.25-..
2.375 60.3 1.000 25.4 TEG7RS6L.5x.25-..
2.375 60.3 1.000 25.4 TEG7RS6L.5x.375-..
2.500 63.5 1.000 25.4 TEG7RS6L.75x.25-..
2.500 63.5 1.000 25.4 TEG7RS6L.75x.375-..
2.500 63.5 1.000 25.4 TEG7RS6L.75x.5-..
2.625 66.7 1.125 28.6 TEG7RS6L1.0x.25-..
2.625 66.7 1.125 28.6 TEG7RS6L1.0x.375-..
2.625 66.7 1.125 28.6 TEG7RS6L1.0x.5-..
2.625 66.7 1.125 28.6 TEG7RS6L1.0x.75-..
2.875 73.0 1.375 34.9 TEG7RS6L1.5x.5-..
2.875 73.0 1.375 34.9 TEG7RS6L1.5x.75-..
2.875 73.0 1.375 34.9 TEG7RS6L1.5x.1.0-..
3.375 85.7 1.625 41.3 TEG7RS6L2.0x.5-..
3.375 85.7 1.625 41.3 TEG7RS6L2.0x.75-..
3.375 85.7 1.625 41.3 TEG7RS6L2.0x1.0-..
2 1
2
2 x 1 1
2 1
⁄
2
⁄
2
x 1 ⁄
2
2 1
1
2 1
⁄
2
x 3 ⁄
4
⁄
2
x 1 *
3.375 85.7 1.625 41.3 TEG7RS6L2.0x1.5-..
3.625 92.1 1.875 47.6 TEG7RS6L2.5x.5-..
3.625 92.1 1.875 47.6 TEG7RS6L2.5x.75-..
3.625 92.1 1.875 47.6 TEG7RS6L2.5x1.0-..
⁄
2
x 1 1 ⁄
2
3.625 92.1 1.875 47.6 TEG7RS6L2.5x1.5-..
⁄
2
x 2 3.625 92.1 1.875 47.6 TEG7RS6L2.5x2.0-..
3 x 1
3 x 3
⁄
2
⁄
4
3 x 1 *
3.875 98.4 2.125 54.0 TEG7RS6L3.0x.5-..
3.875 98.4 2.125 54.0 TEG7RS6L3.0x.75-..
3.875 98.4 2.125 54.0 TEG7RS6L3.0x1.0-..
3 x 1 1
3 x 2
⁄
2
3 x 2 1
4 x 1
4 x 3 ⁄
4
4 x 1 *
⁄
2
⁄
2
3.875 98.4 2.125 54.0 TEG7RS6L3.0x1.5-..
3.875 98.4 2.125 54.0 TEG7RS6L3.0x2.0-..
3.875 98.4 2.125 54.0 TEG7RS6L3.0x2.5-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x.5-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x.75-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x1.0-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x1.5-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x2.0-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x2.5-..
4.750 120.7 2.625 66.7 TEG7RS6L4.0x3.0-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x.5-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x.75-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x1.0-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x1.5-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x2.0-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x2.5-..
7.125 181.0 3.625 92.1 TEG7RS6L6.0x3.0-..
6 x 4 7.125 181.0 3.750 95.3 TEG7RS6L6.0x4.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
Tees - Instrument
TE7IWWCS - INSTRUMENT TEE
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in.
B mm
1
3
3
1
⁄
2
x 1 2.250
57.15
1.000
25.40 TE7IWWCS6L.5x1.0-..
⁄
4
x 1 2.250
57.15
1.000
25.40 TE7IWWCS6L.75x1.0-..
⁄
2
x 1 1 ⁄
2
2.500
63.5
0.875
22.2 TE7IWWCS6L.5x1.5-..
⁄
4
x 1 1 ⁄
2
2.500
63.5
1.000
25.4 TE7IWWCS6L.75x1.5-..
1 x 1 1
1
⁄
2
2.500
63.5
1.125
28.6 TE7IWWCS6L1.0x1.5-..
⁄
2
x 2 2.750
69.9
1.000
25.4 TE7IWWCS6L.5x2.0-..
3 ⁄
4
x 2 2.750
69.9
1.125
28.6 TE7IWWCS6L.75x2.0-..
1 x 2 2.750
69.9
1.250
31.8 TE7IWWCS6L1.0x2.0-..
1 1 ⁄
2
x 2 2.750
69.9
1.500
38.1 TE7IWWCS6L1.5x2.0-..
TEG7IS - INSTRUMENT TEE
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in.
B mm
1
3
⁄
2
x 1 1 ⁄
2
3.000
76.2
0.875
22.2
⁄
4
x 1 1
⁄
2
3.000
76.2
1.000
25.4
* 1 x 1 1
⁄
2
3.000
76.2
1.125
28.6
3
1 ⁄
2
x 2 3.250
82.6
1.000
25.4
⁄
4
x 2 3.250
82.6
1.125
28.6
* 1 x 2 3.250
82.6
1.250
31.8
TEG7IS6L.5x1.5-..
TEG7IS6L.75x1.5-..
TEG7IS6L1.0x1.5-..
TEG7IS6L.5x2.0-..
TEG7IS6L.75x2.0-..
TEG7IS6L1.0x2.0-..
1 1 ⁄
2
x 2 3.250
82.6
1.500
38.1
TEG7IS6L1.5x2.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
BPE TABLE # DT-4.1.2-10
B
B
A
B
A A
A A
BPE TABLE # DT-4.1.2-11
B
Bio-Pharm Fittings 21
Bio-Pharm Fittings
TE31SWW - SHORT CONCENTRIC REDUCER
Reducers - Concentric
L4
L3
A
BPE TABLE # DT-4.1.3-1
* 3
* 1
* 1
* 3
3
⁄
8
x 1 ⁄
4
1.625
⁄
2
x 1 ⁄
4
1.875
⁄
2
x 3 ⁄
8
1.875
⁄
4
x 3 ⁄
8
2.000
⁄
4
x 1 ⁄
2
1 x 1 ⁄
2
2.125
2.500
1 x 3
1 1
1 1
⁄
4
⁄
2
x 3 ⁄
4
3.000
⁄
2
x 1
2 x 1
2.125
2.500
3.375
2 1
2 x 1 1 ⁄
2
2.500
⁄
2
x 1 1 ⁄
2
3.375
2 1 ⁄
2
x 2
3 x 1 1
3 x 2
2.500
⁄
2
4.250
3.375
3 x 2 1
4 x 2
⁄
2
2.625
5.125
4 x 2 1
4 x 3
⁄
2
4.250
3.875
6 x 3
6 x 4
7.250
5.625
TE31SWW - SHORT CONCENTRIC REDUCER
Nominal
Size in.
Dimensions
Overall Length,
A, in
Overall Length,
A, mm
63.5
85.725
63.5
85.725
63.5
107.95
85.725
66.675
41.275
47.625
47.625
50.8
53.975
63.5
53.975
76.2
130.175
107.95
98.425
184.15
142.875
Minimum O.D.
Tangent, Small
End, L3, in.
0.750
0.750
0.750
0.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
Minimum O.D.
Tangent, Small
End, L3, mm
19.05
19.05
19.05
19.05
25.4
25.4
25.4
25.4
25.4
25.4
38.1
38.1
38.1
This product is available in PM and PL surface finishes only.
* Note: Available upon request.
Minimum O.D.
Tangent, Large
End, L4, in.
0.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
Ordering Code
25.4
25.4
25.4
25.4
25.4
25.4
25.4
38.1
Minimum O.D.
Tangent, Large
End, L4, mm.
19.05
25.4
25.4
25.4
25.4
25.4
38.1
38.1
38.1
38.1
38.1
50.8
50.8
TE31SWW6L.375x.25-..
TE31SWW6L.5x.25-..
TE31SWW6L.5x.375-..
TE31SWW6L.75x.375-..
TE31SWW6L.75x.5-..
TE31SWW6L1.0x.5-..
TE31SWW6L1.0x.75-..
TE31SWW6L1.5x.75-..
TE31SWW6L1.5x1.0-..
TE31SWW6L2.0x1.0-..
TE31SWW6L2.0x1.5-..
TE31SWW6L2.5x1.5-..
TE31SWW6L2.5x2.0-..
TE31SWW6L3.0x1.5-..
TE31SWW6L3.0x2.0-..
TE31SWW6L3.0x2.5-..
TE31SWW6L4.0x2.0-..
TE31SWW6L4.0x2.5-..
TE31SWW6L4.0x3.0-..
TE31SWW6L6.0x3.0-..
TE31SWW6L6.0x4.0-..
22
EGMO
NEUMO Ehrenberg Group
Reducers - Concentric
* 3
* 1
* 1
* 3
3
⁄
4
⁄
8
x 1 ⁄
4
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
x
1 x 1
3
⁄
4
x 1 ⁄
2
⁄
2
⁄
8
2.125
2.375
2.375
2.500
2.625
3.000
1 1
1
1 x 3 ⁄
4
2.625
⁄
2
x 3 ⁄
4
3.500
1 ⁄
2
x 1
2 x 1
3.000
3.875
2 1
2 x 1 1 ⁄
2
3.000
⁄
2
x 1 1 ⁄
2
3.875
2 1 ⁄
2
x 2
3 x 1 1
3 x 2
3.000
⁄
2
4.750
3.875
3 x 2 1
4 x 2
⁄
2
3.125
5.750
4 x 2 1
4 x 3
⁄
2
4.875
4.500
6 x 3
6 x 4
8.000
6.375
TE31SCW - SHORT CONCENTRIC REDUCER
Nominal
Size in.
Dimensions
Overall Length,
A, in
Overall Length,
A,mm
76.2
98.425
76.2
98.425
76.2
120.65
98.425
79.375
53.975
60.325
60.325
63.5
66.675
76.2
66.675
88.9
146.05
123.825
114.3
203.2
161.925
Minimum O.D.
Tangent, Small
End, L3, in.
0.750
0.750
0.750
0.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
Minimum O.D.
Tangent, Small
End, L3, mm
19.05
19.05
19.05
19.05
25.4
25.4
25.4
25.4
25.4
25.4
38.1
38.1
38.1
This product is available in PM and PL surface finishes only.
* Note: Available upon request.
Ordering Code
TE31SCW6L.375x.25-..
TE31SCW6L.5x.25-..
TE31SCW6L.5x.375-..
TE31SCW6L.75x.375-..
TE31SCW6L.75x.5-..
TE31SCW6L1.0x.5-..
TE31SCW6L1.0x.75-..
TE31SCW6L1.5x.75-..
TE31SCW6L1.5x1.0-..
TE31SCW6L2.0x1.0-..
TE31SCW6L2.0x1.5-..
TE31SCW6L2.5x1.5-..
TE31SCW6L2.5x2.0-..
TE31SCW6L3.0x1.5-..
TE31SCW6L3.0x2.0-..
TE31SCW6L3.0x2.5-..
TE31SCW6L4.0x2.0-..
TE31SCW6L4.0x2.5-..
TE31SCW6L4.0x3.0-..
TE31SCW6L6.0x3.0-..
TE31SCW6L6.0x4.0-..
TEG31SCC - SHORT CONCENTRIC REDUCER
Nominal Size in.
* 3
* 1
* 1
* 3
3
⁄
4
⁄
8
x 1 ⁄
4
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
x
1 x 1
3
⁄
4
x 1 ⁄
2
⁄
2
⁄
8
1 x 3
1 1
1 1
⁄
4
⁄
2
x 3 ⁄
4
⁄
2
x 1
2 1
2 x 1
2 x 1 1
⁄
2
2 1
⁄
2
x 1 1
⁄
2
⁄
2
x 2
3 x 1 1
⁄
2
3 x 2
3 x 2 1
⁄
2
4 x 2
4 x 2 1
⁄
2
4 x 3
6 x 3
6 x 4
Dimensions
Overall Length, A, in
2.625
2.875
2.875
3.000
3.500
5.250
4.375
3.625
6.250
5.375
5.000
8.500
7.000
3.125
3.500
3.125
4.000
3.500
4.375
3.500
4.375
Overall Length, A, mm
66.675
73.025
73.025
76.2
88.9
133.35
111.125
92.075
158.75
136.525
127
215.9
177.8
79.375
88.9
79.375
101.6
88.9
111.125
88.9
111.125
This product is available in PM and PL surface finishes only.
* Note: Available upon request.
Ordering Code
TEG31SCC6I.375x.25
TEG31SCC6I.5x.25
TEG31SCC6I.5x.375
TEG31SCC6I.75x.375
TEG31SCC6I.75x.5
TEG31SCC6I1.0x.5
TEG31SCC6I1.0x.75
TEG31SCC6I1.5x.75
TEG31SCC6I1.5x1.0
TEG31SCC6I2.0x1.0
TEG31SCC6I2.0x1.5
TEG31SCC6I2.5x1.5
TEG31SCC6I2.5x2.0
TEG31SCC6I3.0x1.5
TEG31SCC6I3.0x2.0
TEG31SCC6I3.0x2.5
TEG31SCC6I4.0x2.0
TEG31SCC6I4.0x2.5
TEG31SCC6I4.0x3.0
TEG31SCC6I6.0x3.0
TEG31SCC6I6.0x4.0
TE31SCW - SHORT CONCENTRIC REDUCER
L3
A
BPE TABLE # DT-4.1.3-2
TEG31SCC - SHORT CONCENTRIC REDUCER
A
BPE TABLE # DT-4.1.3-3
Bio-Pharm Fittings 23
Bio-Pharm Fittings
Reducers - Conical
TEG31I - CONICAL INSTRUMENT REDUCER
B
A
C
TEG31I - SHORT CONICAL INSTRUMENT REDUCER
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in. B mm C in. C mm
3 ⁄
4
x 1 ⁄
2
1.250 31.75 0.620 15.748 0.370 9.398
TEG31L6L.75x.5 -..
1 x 1 ⁄
2
1.250 31.75 0.870 22.098 0.370 9.398
TEG31L6L1.0x.5 -..
1 1
1 x 3 ⁄
4
1.250 31.75 0.870 22.098 0.620 15.748
TEG31L6L1.0x.75 -..
⁄
2
x 1 ⁄
2
1.250 31.75 1.370 34.798 0.370 9.398
TEG31L6L1.5x .5 -..
1 1
1 1
⁄
2
x 3 ⁄
4
1.250 31.75 1.370 34.798 0.620 15.748
TEG31L6L1.5x.75 -..
⁄
2
x 1 1.250 31.75 1.370 34.798 0.870 22.098
TEG31L6L1.5x1.0 -..
2 x 1
2 x 3
2 x 1
⁄
2
1.250 31.75 1.870 47.498 0.370 9.398
TEG31L6L2.0x.5 -..
⁄
4
1.250 31.75 1.870 47.498 0.620 15.748
TEG31L6L2.0x.75 -..
1.250 31.75 1.870 47.498 0.870 22.098
TEG31L6L2.0x1.0 -..
2 x 1 1
2 1
⁄
2
1.250 31.75 1.870 47.498 1.370 34.798
TEG31L6L2.0x1.5 -..
⁄
2 x 1 ⁄
2
1.250 31.75 2.370 60.198 0.370 9.398
TEG31L6L2 .5x.5 -..
2 1
2 1
⁄
2 x 3 ⁄
4
1.250 31.75 2.370 60.198 0.620 15.748
TEG31L6L2.5x.75 -..
⁄
2 x 1 1.250 31.75 2.370 60.198 0.870 22.098
TEG31L6L2.5x1.0 -..
2 1
2 1
⁄
2 x 1 1 ⁄
2
1.250 31.75 2.370 60.198 1.370 34.798
TEG31L6L2.5x1.5 -..
⁄
2 x 2 1.250 31.75 2.370 60.198 1.870 47.498
TEG31L6L2.5x2.0 -..
3 x
3 x 3
1
3 x 1
⁄
2
1.250 31.75 2.870 72.898 0.370 9.398
TEG31L6L3.0x.5 -..
⁄
4
1.250 31.75 2.870 72.898 0.620 15.748
TEG31L6L3.0x.75 -..
1.250 31.75 2.870 72.898 0.870 22.098
TEG31L6L3.0x1.0 -..
3 x 1 1
3 x 2
⁄
2
1.250 31.75 2.870 72.898 1.370 34.798
TEG31L6L3.0x1.5 -..
1.250 31.75 2.870 72.898 1.870 47.498
TEG31L6L3.0x2.0 -..
3 x 2
4 x
4 x 3
1
1 ⁄
2
1.250 31.75 2.870 72.898 2.370 60.198
TEG31L6L3.0x2.5 -..
⁄
2
1.250 31.75 3.834 97.384 0.370 9.398
TEG31L6L4.0x.5 -..
⁄
4
1.250 31.75 3.834 97.384 0.620 15.748
TEG31L6L4.0x.75 -..
4 x 1 1.250 31.75 3.834 97.384 0.870 22.098
TEG31L6L4.0x1.0 -..
4 x 1 1
4 x 2
⁄
2
1.250 31.75 3.834 97.384 1.370 34.798
TEG31L6L4.0x1.5 -..
1.250 31.75 3.834 97.384 1.870 47.498
TEG31L6L4.0x2.0 -..
4 x 2 1
4 x 3
⁄
2
1.250 31.75 3.834 97.384 2.370 60.198
TEG31L6L4.0x2.5 -..
1.250 31.75 3.834 97.384 2.870 72.898
TEG31L6L4.0x3.0 -..
Note: All reducers sizes are 1.250 overall length.
24
EGMO
NEUMO Ehrenberg Group
Reducers - Eccentric
TE32SWW - SHORT ECCENTRIC REDUCER
Nominal
Size in.
Dimensions
6 x 3
6 x 4
Overall Length,
A, in
Overall Length,
A, mm
Minimum O.D.
Tangent, Small
End, L3, in.
* 3
* 1
* 1
* 3
3
⁄
⁄
8
x 1 ⁄
4
1.625
⁄
2
x 1 ⁄
4
1.875
⁄
2
x 3 ⁄
8
1.875
4
x 3 ⁄
8
2.000
⁄
4
x 1 ⁄
2
2.125
1 x 1 ⁄
2
2.500
1 1
1 x 3 ⁄
4
2.125
⁄
2
x 3 ⁄
4
3.000
1 1 ⁄
2
x 1 2.500
2 x 1 3.375
2 1
2 x 1 1 ⁄
2
2.500
⁄
2
x 1 1 ⁄
2
3.375
2 1 ⁄
2
x 2 2.500
3 x 1 1 ⁄
2
4.250
3 x 2 3.375
3 x 2 1
4 x 2
⁄
2
2.625
5.125
4 x 2 1
4 x 3
⁄
2
4.250
3.875
7.250
5.625
41.275
47.625
47.625
50.8
53.975
63.5
53.975
76.2
63.5
85.725
63.5
85.725
63.5
107.95
85.725
66.675
130.175
107.95
98.425
184.15
142.875
0.750
0.750
0.750
0.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
Minimum O.D.
Tangent, Small
End, L3, mm
Minimum O.D.
Tangent, Large
End, L4, in.
19.05
19.05
19.05
19.05
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
38.1
38.1
38.1
0.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
1.500
1.500
1.500
2.000
2.000
Minimum O.D.
Tangent, Large
End, L4, mm
19.05
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
38.1
38.1
38.1
38.1
38.1
38.1
50.8
50.8
Ordering Code
TE32SWW6L.375x.25-..
TE32SWW6L.5x.25-..
TE32SWW6L.5x.375-..
TE32SWW6L.75x.375-..
TE32SWW6L.375x.5-..
TE32SWW6L1.0x.5-..
TE32SWW6L1.0x.75-..
TE32SWW6L1.5x.75-..
TE32SWW6L1.5x1.0-..
TE32SWW6L2.0x1.0-..
TE32SWW6L2.0x1.5-..
TE32SWW6L2.5x1.5-..
TE32SWW6L2.5x2.0-..
TE32SWW6L3.0x1.5-..
TE32SWW6L3.0x2.0-..
TE32SWW6L3.0x2.5-..
TE32SWW6L4.0x2.0-..
TE32SWW6L4.0x2.5-..
TE32SWW6L4.0x3.0-..
TE32SWW6L6.0x3.0-..
TE32SWW6L6.0x4.0-..
This product is available in PM and PL surface finishes only.
* Note: Available upon request.
TE32SWW - SHORT ECCENTRIC REDUCER
L4
L3
A
BPE TABLE # DT-4.1.3-1
Bio-Pharm Fittings 25
Bio-Pharm Fittings
Reducers - Eccentric
TE32SCW - SHORT ECCENTRIC REDUCER
A
L3
A
BPE TABLE # DT-4.1.3-2
* 3
* 1
* 1
* 3
3
⁄
⁄
8
x 1 ⁄
4
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
4
x
1 x 1
3
⁄
4
x 1 ⁄
2
⁄
2
⁄
8
1 x
⁄
2
3
x 3
⁄
4
1 1
1 1 ⁄
2
x 1
2 x 1
⁄
4
2 1
2 x 1 1 ⁄
2
⁄
2
x 1 1 ⁄
2
2 1 ⁄
2
x 2
3 x 1 1
3 x 2
⁄
2
3 x 2 1
4 x 2
⁄
2
4 x 2 1
4 x 3
⁄
2
6 x 3
6 x 4
TE32SCW - SHORT ECCENTRIC REDUCER
Nominal
Size in.
Dimensions
3.000
3.875
3.000
3.875
3.000
4.750
3.875
3.125
2.125
2.375
2.375
2.500
2.625
3.000
2.625
3.500
5.750
4.875
4.500
8.000
6.375
76.2
98.425
76.2
98.425
76.2
120.65
98.425
79.375
53.975
60.325
60.325
63.5
66.675
76.2
66.675
88.9
146.05
123.825
114.3
203.2
161.925
Minimum O.D.
Tangent, Small End,
L3, in.
0.750
0.750
0.750
0.750
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.500
1.500
1.500
Minimum O.D.
Tangent, Small End,
L3, mm.
19.05
19.05
19.05
19.05
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
38.1
38.1
38.1
This product is available in PM and PL surface finishes only.
* Note: Available upon request.
Ordering Code
TE32SCW6L.375x.25-..
TE32SCW6L.5x.25-..
TE32SCW6L.5x.375-..
TE32SCW6L.75x.375-..
TE32SCW6L.75x.5-..
TE32SCW6L1.0x.5-..
TE32SCW6L1x.75-..
TE32SCW6L1.5x.75-..
TE32SCW6L1.5x1.0-..
TE32SCW6L2.0x1.0-..
TE32SCW6L2.0x1.5-..
TE32SCW6L2.5x1.5-..
TE32SCW6L2.5x2.0-..
TE32SCW6L3.0x1.5-..
TE32SCW6L3.0x2.0-..
TE32SCW6L3.0x2.5-..
TE32SCW6L4.0x2.0-..
TE32SCW6L4.0x2.5-..
TE32SCW6L4.0x3.0-..
TE32SCW6L6.0x3.0-..
TE32SCW6L6.0x4.0-..
26
EGMO
NEUMO Ehrenberg Group
Reducers - Eccentric
TEG32SCC - SHORT ECCENTRIC REDCER
Nominal
Size in. Dimensions
Overall Length,
A, in
* 3
* 1
* 1
* 3
3
⁄
⁄
8
x 1 ⁄
4
2.625
⁄
2
x 1
⁄
4
2.875
⁄
2
x 3
⁄
8
2.875
4
x
⁄
4
x 1
⁄
2
1 x 1
3
⁄
2
⁄
8
3.000
3.125
1 x
1 1
1 1
3
⁄
4
⁄
2
x 3
⁄
4
4.000
⁄
2
x 1
3.500
3.125
3.500
2 1
2 x 1
2 x 1 1
⁄
2
4.375
3.500
⁄
2
x 1 1
⁄
2
4.375
2 1
⁄
2
x 2
3 x 1 1
3.500
⁄
2
5.250
3 x 2
3 x 2 1
4 x 2
⁄
2
3.625
6.250
4 x 2 1
4 x 3
⁄
2
4.375
5.375
5.000
6 x 3
6 x 4
8.500
7.000
Overall Length,
A, mm
88.9
111.125
88.9
111.125
88.9
133.35
111.125
92.075
66.675
73.025
73.025
76.2
79.375
88.9
79.375
101.6
158.75
136.525
127
215.9
177.8
Ordering Code
TEG32SCC6L.375x.25-..
TEG32SCC6L.5x.25-..
TEG32SCC6L.5x.375-..
TEG32SCC6L.75x.375-..
TEG32SCC6L.75x.5-..
TEG32SCC6L1.0x.5-..
TEG32SCC6L1.0x.75-..
TEG32SCC6L1.5x.75-..
TEG32SCC6L1.5x1.0-..
TEG32SCC6L2.0x1.0-..
TEG32SCC6L2.0x1.5-..
TEG32SCC6L2.5x1.5-..
TEG32SCC6L2.5x2.0-..
TEG32SCC6L3.0x1.5-..
TEG32SCC6L3.0x2.0-..
TEG32SCC6L3.0x2.5-..
TEG32SCC6L4.0x2.0-..
TEG32SCC6L4.0x2.5-..
TEG32SCC6L4.0x3.0-..
TEG32SCC6L6.0x3.0-..
TEG32SCC6L6.0x4.0-..
This product is available in PM and PL surface finishes only.
* Note: Available upon request.
TEG32SCC - SHORT ECCENTRIC REDCER
A
BPE TABLE # DT-4.1.3-3
Bio-Pharm Fittings 27
28
Bio-Pharm Fittings
A
Use Points
A A
A
A A
A
A A
A
B B
B
B B
B
C C
C
B B
B
C C
C
B
C
A
A
C
TE2UBWWW - 180° BOTTOM
OUTLET WELD USE POINT
Nominal
Size in.
Dimensions Ordering Code
A in.
A mm B in.
B mm C in.
C mm
3
3
1 1
⁄
4
x 1 ⁄
2
4.500
114.3
3.000
76.2
1.875
47.6
TE2UBWWW6L.75x.5-..
⁄
4
x 3 ⁄
4
4.500
114.3
3.000
76.2
1.875
47.6
TE2UBWWW6L.75x.75-..
1 x 1 ⁄
2
3.000
76.2
3.000
76.2
2.062
52.4
TE2UBWWW6L1.0x.5-..
⁄
2
x 1 ⁄
2
4.500
114.3
4.500
114.3
2.312
58.7
TE2UBWWW6L1.5x.5-..
2 1
2 x 1 ⁄
2
6.000
152.4
5.000
127.0
2.562
65.1
TE2UBWWW6L2.0x.5-..
⁄
2
x 1 ⁄
2
7.500
190.5
5.750
146.1
2.812
71.4
TE2UBWWW6L2.5x.5-..
3 x 1
4 x 1
⁄
2
9.000
228.6
6.500
165.1
3.062
77.8
TE2UBWWW6L3.0x.5-..
⁄
2
12.000
304.8
8.500
215.9
3.562
90.5
TE2UBWWW6L4.0x.5-..
A & B Dimensions According to ASME BPE 2014, table DT-4.1.1-7
B
TE2UBWWC - 180° BOTTOM
OUTLET CLAMP USE POINT
Nominal
Size in.
Dimensions Ordering Code
A in.
A mm B in.
B mm C in.
C mm
3
3
1 1
⁄
4
x 1 ⁄
2
4.500
114.3
3.000
76.2
0.875
22.2
TE2UBWWC6L.75x.5-..
⁄
4
x 3 ⁄
4
4.500
114.3
3.000
76.2
0.875
22.2
TE2UBWWC6L.75x.75-..
1 x 1 ⁄
2
3.000
76.2
3.000
76.2
1.062
27 TE2UBWWC6L1.0x.5-..
⁄
2
x 1 ⁄
2
4.500
114.3
4.500
114.3
1.312
33.3
TE2UBWWC6L1.5x.5-..
2 1
2 x 1 ⁄
2
6.000
152.4
5.000
127 1.562
39.7
TE2UBWWC6L2.0x.5-..
⁄
2
x 1 ⁄
2
7.500
190.5
5.750
146.1
1.812
46 TE2UBWWC6L2.5x.5-..
3 x 1
4 x 1
⁄
2
9.000
228.6
6.500
165.1
2.062
52.4
TE2UBWWC6L3.0x.5-..
⁄
2
12.000
304.8
8.500
215.9
2.562
65.1
TE2UBWWC6L4.0x.5-..
A & B Dimensions According to ASME BPE 2014, table DT-4.1.1-7
B
TE2USWWC - 180° SIDE
OUTLET CLAMP USE POINT
Nominal
Size in.
Dimensions Ordering Code
A in.
A mm B in.
B mm C in.
C mm
3
3
1 1
⁄
4
x 1 ⁄
2
4.500
114.3
3.000
76.2
0.875
22.2
TE2USWWC6L.75x.5-..
⁄
4
x 3 ⁄
4
4.500
114.3
3.000
76.2
0.875
22.2
TE2USWWC6L.75x.75-..
1 x 1 ⁄
2
3.000
76.2
3.000
76.2
1.062
26.9
TE2USWWC6L1.0x.5-..
⁄
2
x 1 ⁄
2
4.500
114.3
4.500
114.3
1.312
33.3
TE2USWWC6L1.5x.5-..
2 1
2 x 1 ⁄
2
6.000
152.4
5.000
127 1.562
39.7
TE2USWWC6L2.0x.5-..
⁄
2
x 1 ⁄
2
7.500
190.5
5.750
146.1
1.812
46 TE2USWWC6L2.5x.5-..
3 x 1
4 x 1
⁄
2
9.000
228.6
6.500
165.1
2.062
52.4
TE2USWWC6L3.0x.5-..
⁄
2
12.000
304.8
8.500
215.9
2.562
65 TE2USWWC6L4.0x.5-..
A & B Dimensions According to ASME BPE 2014, table DT-4.1.1-7
C C
C
EGMO
NEUMO Ehrenberg Group
True Y’s & Laterals
TE28WB - TRUE Y
Nominal
Size in.
Dimensions
1 1
1
⁄
2
2
2 1
3
⁄
2
4
6
A in.
3.000
3.000
4.000
5.000
6.000
8.000
8.000
A mm Nom. Wall
76.2
76.2
101.6
127.0
152.4
203.2
203.2
.065
.065
.065
.065
.065
.083
.109
Ordering Code
TE28WB6L1.0-..
TE28WB6L1.5-..
TE28WB6L2.0-..
TE28WB6L2.5-..
TE28WB6L3.0-..
TE28WB6L4.0-..
TE28WB6L6.0-..
TEG28B - CLAMP TRUE Y
Nominal
Size in.
Dimensions
* 1
1 1
2
2 1
3
⁄
2
⁄
2
A in.
3.500
3.500
4.500
5.500
6.500
A mm
88.9
88.9
114.3
139.7
165.1
Ordering Code
TEG28B6L1.0-..
TEG28B6L1.5-..
TEG28B6L2.0-..
TEG28B6L2.5-..
TEG28B6L3.0-..
4
6
8.625
8.875
219.1
225.4
TEG28B6L4.0-..
TEG28B6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
A
A
A
A
A
A
A
B
C
B
A
B
C
B
A
B
C
B
A
A
D
D
C
A
Bio-Pharm Fittings 29
A
A
A
A
Bio-Pharm Fittings
A
A
True Y’s & Laterals
A
A
B
D
C
B
A
B
D
C
B A
B
C
B A
C
A
TE28WA - 45° LATERAL
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in. B mm C in. C mm D in. D mm
* 1 6.000 152.4 5.000 127.0 1.000 25.4 1.000 25.4 TE28WA6L1.0-..
1 1
2
⁄
2
7.380 187.45 6.190 157.2 1.190 30.2 1.500 38.1 TE28WA6L1.5-..
8.750 222.3 7.120 181.0 1.630 41.4 2.000 50.8 TE28WA6L2.0-..
2 1
3
⁄
2
10.000 254.0 8.500 215.9 1.500 38.1 2.500 63.50 TE28WA6L2.5-..
10.750 270.1 8.870 225.4 1.870 47.5 3.000 76.2 TE28WA6L3.0-..
4
6
12.810 325.4 10.750 273.1 2.060 52.4 4.000 101.6 TE28WA6L4.0-..
16.500 419.1 12.500 317.5 4.000 101.6 6.000 152.4 TE28WA6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the
ASME BPE standard.
TEG28A - 45° CLAMP LATERAL
Nominal
Size in.
Dimensions Ordering Code
A in. A mm B in. B mm C in. C mm
* 1
4
6
7.000 177.8 5.500 139.7 1.500 38.1
1 1
2
⁄
2
8.375 212.7 6.687 169.9 1.687 42.9
9.750 247.7 7.625 193.7 2.125 54.0
2 1
3
⁄
2
11.000 279.4 9.000 228.6 2.000 50.8
11.750 298.5 9.375 238.1 2.375 60.3
14.062 357.2 11.375 288.9 2.687 68.3
18.250 479.4 15.375 390.5 4.375 111.1
TEG28A6L1.0-..
TEG28A6L1.5-..
TEG28A6L2.0-..
TEG28A6L2.5-..
TEG28A6L3.0-..
TEG28A6L4.0-..
TEG28A6L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the
ASME BPE standard.
30
EGMO
NEUMO Ehrenberg Group
Crosses
TE9WWWW - CROSS
Nominal
Size in.
Ordering Code
A in. A mm B in. B mm
1
3
1
3
1
⁄
4
1.750 44.5 3.500 89.0 TE9WWWW6L.25-..
⁄
8
1.750 44.5 3.500 89.0 TE9WWWW6L.375-..
⁄
2
1.875 47.6 3.750 95.2 TE9WWWW6L.5-..
⁄
4
2.000 50.8 4.000 101.6 TE9WWWW6L.75-..
2.125
54 4.250 108.0 TE9WWWW6L1.0-..
1 1
2
⁄
2
2.375 60.3 4.750 120.6 TE9WWWW6L1.5-..
2.875
73 5.750 146.0 TE9WWWW6L2.0-..
2 1
3
⁄
2
3.125 79.4 6.250 158.8 TE9WWWW6L2.5-..
3.375 85.7 6.750 171.4 TE9WWWW6L3.0-..
4
6
4.125 104.8 8.250 209.6 TE9WWWW6L4.0-..
5.625 142.9 11.250 285.8 TE9WWWW6L6.0-..
TEG9 - CROSS
Nominal
Size in.
Ordering Code
A in. A mm B in. B mm
1
3
1
3
⁄
4
2.250 57.2 4.500 114.3
⁄
8
2.250 57.2 4.500 114.3
⁄
2
2.250 57.2 4.500 114.3
⁄
4
2.375 60.3 4.750 120.6
* 1 2.625 66.7 5.250 133.4
1 1
2
⁄
2
2.875 73.0 5.750 146.0
3.375 85.7 6.750 171.4
2 1
3
⁄
2
3.625 92.1 7.250 184.2
3.875 98.4 7.750 196.8
4
6
4.750 120.7 9.500 241.4
7.125 181.0 14.250 362.0
TEG96L.25-..
TEG96L.375-..
TEG96L.5-..
TEG96L.75-..
TEG96L1.0-..
TEG96L1.5-..
TEG96L2.0-..
TEG96L2.5-..
TEG96L3.0-..
TEG96L4.0-..
TEG96L6.0-..
* Note: 1” Clamp Ferrule can also be orderd with “Type A” connections according to the ASME BPE standard.
B
A
B
A
A
B
BPE TABLE# DT-4.1.2-1
A
B
B
A
B
A
B
B
BPE TABLE# DT-4.1.2-4
A
A
A
B
A B
B
B
Bio-Pharm Fittings 31
B
A
A
B
B
A
Crosses
A A
B
B
TE9RWWWW - REDUCING CROSS
Nominal
Size in.
A in.
A mm B in.
B mm
3
1
1
3
⁄
8
x 1
⁄
4
1.750
44.5
1.750
44.5
⁄
2
x 1 ⁄
4
1.875
47.6
1.875
47.6
⁄
2
x 3 ⁄
8
1.875
47.6
1.875
47.6
⁄
4
x 1 ⁄
4
2.000
50.8
2.000
50.8
3
3
⁄
4
x 3 ⁄
8
2.000
50.8
2.000
50.8
⁄
4
x 1 ⁄
2
2.000
50.8
2.000
50.8
1 x 1
1 x 3
⁄
4
2.125
54.0
2.125
54.0
⁄
8
2.125
54.0
2.125
54.0
1
1 x 1
1 x
1
3 ⁄
⁄
2
2.125
54.0
2.125
54.0
4
2.125
54.0
2.125
54.0
⁄
2
x 1 ⁄
2
2.375
60.3
2.375
60.3
1 1
1 1
⁄
2
x 3 ⁄
4
2.375
60.3
2.375
60.3
⁄
2
x 1 2.375
60.3
2.375
60.3
2 x 1
2 x 3
2 x 1
⁄
2
2.875
73.0
2.625
66.7
⁄
4
2.875
73.0
2.625
66.7
2.875
73.0
2.625
66.7
2 x 1
2 1
1 ⁄
2
2.875
73.0
2.625
66.7
⁄
2
x 1 ⁄
2
3.125
79.4
2.875
73.0
2 1
2 1
⁄
2
x 3 ⁄
4
3.125
79.4
2.875
73.0
⁄
2
x 1 3.125
79.4
2.875
73.0
2 1
2 1
⁄
2
x 1 1 ⁄
2
3.125
79.4
2.875
73.0
⁄
2
x 2 3.125
79.4
2.875
73.0
3 x 1
3 x 3
⁄
2
3.375
85.7
3.125
79.4
⁄
4
3.375
85.7
3.125
79.4
3 x 1
3 x 1 1
3.375
85.7
3.125
79.4
⁄
2
3.375
85.7
3.125
79.4
3 x 2
3 x 2 1
4 x 1
4 x 3
⁄
2
3.375
3.375
85.7
85.7
3.125
79.4
3.125
79.4
⁄
2
4.125
104.8
3.625
92.1
⁄
4
4.125
104.8
3.625
92.1
4 x 1
4 x 1 1
4.125
104.8
3.625
92.1
⁄
2
4.125
104.8
3.625
92.1
4 x 2
4 x 2 1
4.125
104.8
3.875
98.4
⁄
2
4.125
104.8
3.875
98.4
4 x 3 4.125
104.8
3.875
98.4
6 x 3
6 x 4
5.625
142.9
4.875
123.8
5.625
142.9
5.125
130.2
Note: Additional sizes are available upon request.
Ordering Code
TE9RWWWW6L.375x.25-..
TE9RWWWW6L.5x.25-..
TE9RWWWW6L.5x.375-..
TE9RWWWW6L.75x.25-..
TE9RWWWW6L.75x.375-..
TE9RWWWW6L.75x.25-..
TE9RWWWW6L1.0x.375
TE9RWWWW6L1.0x.5
TE9RWWWW6L1.5x.75-..
TE9RWWWW6L1.0x.375-..
TE9RWWWW6L.1.5x.5-..
TE9RWWWW6L.1.5x.75-..
TE9RWWWW6L.1.5x1.0-..
TE9RWWWW6L2.0x.5-..
TE9RWWWW6L2.0x.75-..
TE9RWWWW6L2.0x1.0-..
TE9RWWWW6L2.0x1.5-..
TE9RWWWW6L.2.5x..5-..
TE9RWWWW6L.2.5x.75-..
TE9RWWWW6L2.5x1.0-..
TE9RWWWW6L2.5x1.5-..
TE9RWWWW6L2.5x2.0-..
TE9RWWWW6L3.0x.5-..
TE9RWWWW6L3.0x.75-..
TE9RWWWW6L3.0x1.0-..
TE9RWWWW6L3.0x1.5-..
TE9RWWWW6L3.0x2.0-..
TE9RWWWW6L3.0x2.5-..
TE9RWWWW6L4.0x.5-..
TE9RWWWW6L4.0x.75-..
TE9RWWWW6L4.0x1.0-..
TE9RWWWW6L4.0x1.5-..
TE9RWWWW6L4.0x2.0-..
TE9RWWWW6L4.0x2.5-..
TE9RWWWW6L4.0x3.0-..
TE9RWWWW6L.6.0x.3.0-..
TE9RWWWW6L6.0x4.0-..
32
EGMO
NEUMO Ehrenberg Group
Ferrules
TEG14AM7 - CLAMP FERRULE LONG
Nominal
Size in.
Ordering Code
Type A in. A mm D in. D mm
3
3
1
1
1
⁄
4
⁄
2
⁄
8
⁄
4
1
1 1
2
⁄
2
2 1
4
6
3
⁄
2
B
B
A
B
A
A
A
A
B
B
B
B
1.750
44.5
0.984
24.9
1.750
44.5
0.984
24.9
1.750
44.5
0.984
24.9
1.750
44.5
0.984
24.9
1.750
44.5
1.339
34.0
1.750
44.5
1.984
50.3
1.750
44.5
1.984
50.3
2.250
57.2
2.516
63.9
2.250
57.2
3.047
77.3
2.250
57.2
3.579
90.9
2.250
57.2
4.682
118.9
3.000
76.2
6.570
166.8
For type A&B technical information please refer to page 46
TEG14AM7 6L.25-..
TEG14AM7 6L.375-..
TEG14AM7 6L.5-..
TEG14AM7 6L.75-..
TEG14AM7 6L1.0-A..
TEG14AM7 6L1.0-..
TEG14AM7 6L1.5-..
TEG14AM7 6L2.0-..
TEG14AM7 6L2.5-..
TEG14AM7 6L3.0-..
TEG14AM7 6L4.0-..
TEG14AM7 6L6.0-..
TEG14BM7 - CLAMP FERRULE MEDIUM
Nominal
Size in.
Ordering Code
3
3
1
1
1 1
2 1
1
⁄
4
⁄
2
⁄
8
⁄
4
1
⁄
2
2
⁄
2
3
4
B
B
B
B
B
B
A
A
Type A in. A mm D in. D mm
A 1.130
28.7
0.984
24.9
A
A
1.130
1.130
28.7
28.7
0.984
0.984
24.9
24.9
1.130
1.130
1.130
1.130
28.7
28.7
28.7
28.7
0.984
1.339
1.984
1.984
24.9
34.0
50.3
50.3
1.130
28.7
2.516
63.9
1.130
28.7
3.047
77.3
1.130
28.7
3.579
90.9
1.130
28.7
4.682
118.9
TEG14BM7 6L.25-..
TEG14BM7 6L.375-..
TEG14BM7 6L.5-..
TEG14BM7 6L.75-..
TEG14BM7 6L1.0-A..
TEG14BM7 6L1.0-..
TEG14BM7 6L1.5-..
TEG14BM7 6L2.0-..
TEG14BM7 6L2.5-..
TEG14BM7 6L3.0-..
TEG14BM7 6L4.0-..
6 B 1.500
38.1
6.570
166.8
TEG14BM7 6L6.0-..
For type A&B technical information please refer to page 46
TEG2CS - CLAMP FERRULE SHORT
Nominal
Size in.
Type A in. A mm D in. D mm
3
3
1
1
1
⁄
4
⁄
2
⁄
8
⁄
4
1
1 1
2
⁄
2
2 1
4
6
3
⁄
2
B
B
A
B
A
A
A
A
B
B
B
B
0.500
12.7
0.984
24.9
0.500
12.7
0.984
24.9
0.500
12.7
0.984
24.9
0.500
12.7
0.984
24.9
0.500
12.7
1.339
34.0
0.500
12.7
1.984
50.3
0.500
12.7
1.984
50.3
0.500
12.7
2.516
63.9
0.500
12.7
3.047
77.3
0.500
12.7
3.579
90.9
0.625
15.9
4.682
118.9
0.750
19.1
6.570
166.8
For type A&B technical information please refer to page 46
Ordering Code
TEG2CS 6L.25-..
TEG2CS 6L.375-..
TEG2CS 6L.5-..
TEG2CS 6L.75-..
TEG2CS 6L1.0-A..
TEG2CS 6L1.0-..
TEG2CS 6L1.5-..
TEG2CS 6L2.0-..
TEG2CS 6L2.5-..
TEG2CS 6L3.0-..
TEG2CS 6L4.0-..
TEG2CS 6L6.0-..
ø D
ø D
ø D
A
A
ø D
ø D
ø D
A
A
ø D
ø D
ø D
A
A
A
BPE TABLE # DT-4.1.4-1(C)
Bio-Pharm Fittings 33
A
ø D
Bio-Pharm Fittings
Solid End Caps & Weld Caps
A
BPE TABLE # DT-4.1.5-1
ø D
BPE TABLE # DT-4.1.5-2
A B
A
TE16W - WELD CAP
Nominal Size in.
1
3
1
⁄
2
⁄
4
1 1 ⁄
2
2 1
2
⁄
2
3
4
6
A in.
1.500
1.500
1.500
1.500
1.500
1.500
1.750
2.000
2.500
A mm
38.1
38.1
38.1
38.1
38.1
38.1
44.5
50.8
63.5
Ordering Code
TE16W6L.5-..
TE16W6L.75-..
TE16W6L1.0-..
TE16W6L1.5-..
TE16W6L2.0-..
TE16W6L2.5-..
TE16W6L3.0-..
TE16W6L4.0-..
TE16W6L6.0-..
TEG16A - SOLID END CAP
Nominal
Size in.
A in.
A mm.
1
3
1
3
⁄
2
⁄
4
⁄
4
⁄
8
0.187
0.187
0.187
0.187
1 (Type A) 0.250
1
1 1
2
⁄
2
2 1
4
6
3
⁄
2
0.250
0.250
0.250
0.250
0.250
0.312
0.437
6.4
6.4
6.4
6.4
4.7
4.7
4.7
4.7
6.4
6.4
7.9
11.1
D in.
D mm.
0.984
0.984
0.984
0.984
1.339
1.984
1.984
2.516
3.047
3.579
4.682
6.570
24.9
24.9
24.9
24.9
34.0
50.3
50.3
63.9
77.3
90.9
118.9
166.8
Ordering Code
TEG16A6L.75-..
TEG16A6L.75-..
TEG16A6L.75-..
TEG16A6L.75-..
TEG16A6L1.0-A..
TEG16A6L1.5-..
TEG16A6L1.5-..
TEG16A6L2.0-..
TEG16A6L2.5-..
TEG16A6L3.0-..
TEG16A6L4.0-..
TEG16A6L6.0-..
C
A B
A
W
34
A B
A B
C
EGMO
NEUMO Ehrenberg Group
W
ø D
A
ø D
A
A
A
Gaskets
A B
C
A B
A B
C W
TEG40 - GASKET
A B
A in. A mm B in. B mm C in. C mm W in. W mm
1
3
⁄
2
1.000 25.40 0.370 9.40
-
⁄
4
1.000 25.40 0.618 15.70
-
-
1 Type A 1.340 34.00 0.900 22.86 0.20
5.08
1 1
2 1
1
2
⁄
2
1.975 50.16 0.900 22.86 0.20
5.08
1.975 50.16 1.400 35.56 0.20
5.08
2.500 63.50 1.900 48.26 0.20
5.08
⁄
2
3.000 76.20 2.400 60.96 0.20
5.08
-
-
-
-
3 3.575 90.80 2.900 73.66 0.20
5.08
-
0.22
5.50
0.22
5.50
-
-
-
-
-
-
-
4
6
4.690 119.12 3.875 98.42 0.20
5.08
6.600 167.64 5.840 148.33 0.20
5.08
* Please specify the gasket material.
Note: Gaskets are type USP Class VI Pharmaceutical Grade.
-
-
-
-
Ordering Code
TEG40.5*
TEG40.75*
TEG401.0-A*
TEG401.0*
TEG401.5*
TEG402.0*
TEG402.5*
TEG403.0*
TEG404.0*
TEG406.0*
GASKET MATERIALS:
PTFE®
VITON®
Envelope type - TEFLON with EPDM Filler
TEFLON with VITON Filler
SILICON
BUNA
EPDM and TEF-STEEL®
Bio-Pharm Fittings 35
Bio-Pharm Fittings
Clamps
A
A
A
13MHHMD -
DOUBLE HINGED HEAVY DUTY CLAMP
Nominal
Size in.
Ordering Code
1 1
2
⁄
2
2 1
3
⁄
2
4
A in.
2.122
2.654
3.185
3.717
4.820
A mm
53.9
67.4
80.8
94.4
108.7
13MHHMD1.5
13MHHMD2.0
13MHHMD2.5
13MHHMD3.0
13MHHMD4.0
13MHHM -
HEAVY DUTY CLAMP
Nominal
Size in.
1 ⁄
2
& 3 ⁄
4
1 Type A
1 & 1 1
2
⁄
2
2 1
3
⁄
2
4
6
A in.
1.125
1.472
2.122
2.654
3.185
3.717
4.820
6.695
A mm
28.5
37.4
53.9
64.5
80.8
94.4
122.42
170.05
Ordering Code
13MHHM.5
13MHHM1.0-A
13MHHM1
13MHHM2.0
13MHHM2.5
13MHHM3.0
13MHHM4.0
13MHHM6.0
13MHHM-H
HEAVY DUTY CLAMP (WING NUT WITH HOLE)
Nominal
Size in.
Ordering Code
1 ⁄
2
& 3 ⁄
4
1 Type A
1 & 1 1
2
⁄
2
2 1
3
⁄
2
4
6
A in.
1.125
1.472
2.122
2.654
3.185
3.717
4.820
6.695
A mm
28.9
37.4
53.9
67.4
80.8
94.4
122.4
170.05
13MHHM.5-H
13MHHM1.0-H-A
13MHHM1-H
13MHHM2.0-H
13MHHM2.5-H
13MHHM3.0-H
13MHHM4.0-H
13MHHM6.0-H
36
EGMO
NEUMO Ehrenberg Group
Clamps
13MHHS -
THREE PIECE HEAVY DUTY CLAMP
Nominal
Size in.
Ordering Code
1 1
2
⁄
2
2 1
3
⁄
2
4
A in.
2.122
2.654
3.185
3.717
4.820
A mm
53.9
67.4
80.8
94.4
108.7
13MHHS1.5
13MHHS2.0
13MHHS2.5
13MHHS3.0
13MHHS4.0
13MHP -
HIGH PRESSURE CLAMP
Nominal
Size in.
1 ⁄
2
& 3 ⁄
4
1 1
2
⁄
2
2 1
3
⁄
2
4
6
A in.
1.062
2.046
2.578
3.110
3.640
4.744
6.632
A mm
26.97
51.97
65.48
78.99
92.46
120.50
168.45
Ordering Code
13MHP.5
13MHP1.5
13MHP2.0
13MHP2.5
13MHP3.0
13MHP4.0
13MHP6.0
A
A
Bio-Pharm Fittings 37
A
T
B
B
A
A
Bio-Pharm Fittings
Hose Adapters
A
C
D
A-A
A
A
A
1’’ THROUGH 4’’
A
½” & ¾” SIZES
A
TEG14RT - HOSE ADAPTER
Nominal
Size in.
Ordering Code
1
1
1
3
3
3
⁄
2 x
1
⁄
4
⁄
2 x
3
⁄
8
⁄
2 x
1
⁄
2
⁄
4 x
1
⁄
4
⁄
4 x
3
⁄
8
⁄
4 x
1
⁄
2
3 ⁄
4
* 1
1 1
2
⁄
2
2 1
3
⁄
2
4
1.690
1.690
2.310
2.300
3.090
3.410
A in.
1.500
1.500
1.500
1.500
1.500
1.500
1.500
42.9
42.9
58.7
59.5
78.6
86.5
A mm
38.1
38.1
38.1
38.1
38.1
38.1
38.1
TEG14RT6L.5x.25-..
TEG14RT6L.5x.375-..
TEG14RT6L.5x.5-..
TEG14RT6L.75x.25-..
TEG14RT6L.75x.375-..
TEG14RT6L.75x.5-..
TEG14RT6L.75-..
TEG14RT6L1.0-..
TEG14RT6L1.5-..
TEG14RT6L2.0-..
TEG14RT6L2.5-..
TEG14RT6L3.0-..
TEG14RT6L4.0-..
* Note: 1” Clamp Ferrule can also be ordered with ‘Type A’ connections according to the ASME BPE 2014 standard.
TEG21 - CLAMP ADAPTER X MALE NPT
Nominal
Size in.
Ordering Code
1
3
3
3
3
3
1 ⁄
2
x 1 ⁄
8
1 ⁄
2
x 1 ⁄
4
1
1
⁄
2
x 3 ⁄
8
⁄
2
x 1 ⁄
2
⁄
2
x 3 ⁄
4
⁄
4
x 1 ⁄
8
⁄
4
x 1 ⁄
4
⁄
4
x 3 ⁄
8
⁄
4
x 1 ⁄
2
⁄
4
x 3 ⁄
4
* 1
1 1
2
⁄
2
2 1
3
⁄
2
4
2.000
2.000
2.000
2.250
2.440
2.660
3.280
3.500
3.810
A in.
2.000
2.000
2.000
2.000
2.000
2.000
2.000
50.8
50.8
50.8
57.1
61.9
67.5
83.3
88.9
96.7
A mm
50.8
50.8
50.8
50.8
50.8
50.8
50.8
TEG216L.5x.125-..
TEG216L.5x.25-..
TEG216L.5x.375-..
TEG216L.5-..
TEG216L.5x.75-..
TEG216L.75x.125-..
TEG216L.75x.25-..
TEG216L.75x.375-..
TEG216L.75x.5-..
TEG216L.75-..
TEG216L1.0-..
TEG216L1.5-..
TEG216L2.0-..
TEG216L2.5-..
TEG216L3.0-..
TEG216L4.0-..
* Note: 1” Clamp Ferrule can also be ordered with ‘Type A’ connections according to the ASME BPE 2014 standard
38
A
A
EGMO
NEUMO Ehrenberg Group
A
A
Adapters
TEG22 - CLAMP ADAPTER X FEMALE NPT
Nominal
Size in.
Ordering Code
1
1
1
1
1
3
3
3
3
3
⁄
2
x 1 ⁄
8
⁄
2
x 1 ⁄
4
⁄
2
x 3 ⁄
8
⁄
2
x 1 ⁄
2
⁄
2
x 3 ⁄
4
⁄
4
x 1 ⁄
8
⁄
4
x 1 ⁄
4
⁄
4
x 3 ⁄
8
⁄
4
x 1 ⁄
2
⁄
4
x 3 ⁄
4
* 1
1 1
2
⁄
2
2 1
3
⁄
2
4
2.000
2.000
2.000
2.250
2.440
2.660
3.280
3.500
3.810
A in.
2.000
2.000
2.000
2.000
2.000
2.000
2.000
50.8
50.8
50.8
57.1
61.9
67.5
83.3
88.9
96.7
A mm
50.8
50.8
50.8
50.8
50.8
50.8
50.8
TEG226L.5x.125-..
TEG226L.5x.25-..
TEG226L.5x.375-..
TEG226L.5-..
TEG226L.5x.75-..
TEG226L.75x.125-..
TEG226L.75x.25-..
TEG226L.75x.375-..
TEG226L.75x.5-..
TEG226L.75-..
TEG226L1.0-..
TEG226L1.5-..
TEG226L2.0-..
TEG226L2.5-..
TEG226L3.0-..
TEG226L4.0-..
* Note: 1” Clamp Ferrule can also be ordered with ‘Type A’ connections according to the ASME BPE 2012 standard.
Stub Ends & Slip On Flanges
TE14WA - TYPE A STUB END WITH GROOVES
Nominal
Size in.
Ordering Code
1
3
A in. A mm B in.
B mm T in.
T mm
⁄
2
2.000
50.80
1.625
41.3
0.065
1.65
TE14WA6L.5-..
⁄
4
2.000
50.80
1.687
42.9
0.065
1.65
TE14WA6L.75-..
1 1
1 2.000
50.80
2.000
50.8
0.065
1.65
TE14WA6L1.0-..
⁄
2
2.000
50.80
2.875
73 0.065
1.65
TE14WA6L1.5-..
2 1
2 2.500
63.50
3.265
92.1
0.065
1.65
TE14WA6L2.0-..
⁄
2
2.500
63.50
4.125
104.8
0.065
1.65
TE14WA6L2.5-..
3 2.500
63.50
5.000
127 0.065
1.65
TE14WA6L3.0-..
4
6
2.500
63.50
6.187
157.2
0.083
2.11
3.000
76.20
8.500
215.9
0.109
2.77
TE14WA6L4.0-..
TE14WA6L6.0-..
E38SL - SLIP ON FLANGE
Nominal
Size in.
A in.
A mm B in.
B mm C in.
C mm D in.
D mm
1 1
1 4.250
108.0
3.125
79.4
0.375
9.5
1.010
25.7
⁄
2
5.000
127.0
3.875
98.4
0.437
11.1
1.510
38.4
2 1
2 6.000
152.4
4.750
120.7
0.500
12.7
2.010
51.1
⁄
2
7.000
177.8
5.500
139.7
0.562
14.3
2.510
63.8
3 7.500
190.5
6.000
152.4
0.625
15.9
3.010
76.5
4
6
9.000
228.6
7.500
190.5
0.689
17.5
4.010
101.9
11.000 297.4
9.500
241.3
0.811
20.6
6.010
152.9
A
A
T
T
½” & ¾” SIZES
1’’ THROUGH 4’’
B
B
B
B
A
A
A
A C
C
D
D
A
A
Bio-Pharm Fittings 39
A
A
40
Bio-Pharm Fittings
Asme Bpe Dt Index
Drawing Part description
TE2S - 90° Elbow
2009 DT
According to ASME-BPE
2009
2012 DT
According to ASME-BPE
2012
2014 Dt
According to ASME-BPE
2014
DT-7 DT-4.1.1-1 DT-4.1.1-1
TE2C - 90° Elbow clamp one end
TEG2C-90° Elbow cc
DT-12 DT-4.1.1-2
DT-16 DT-4.1.1-3
DT-4.1.1-2
DT-4.1.1-3
TE2KS - 45° Elbow WW
TE2KC - 45° Elbow clamp one end
DT-8
DT-13
DT-4.1.1-4
DT-4.1.1-5
TEG2K-45° Elbow CC
Elbow 180° WW
(TE2UBWWW - 180° bottom outlet weld use point)
DT-17
DT-23
TE7WWW - Equal Tee WWW DT-9
DT-4.1.1-6
DT-4.1.1-7
DT-4.1.2-1
TE9WWWW - Equal Cross WWWW DT-9 DT-4.1.2-1
DT-4.1.1-4
DT-4.1.1-5
DT-4.1.1-6
DT-4.1.1-7
DT-4.1.2-1
DT-4.1.2-1
EGMO
NEUMO Ehrenberg Group
Asme Bpe Dt Index
Drawing Part description
TE7WWCS - Short outlet Tee
2009 DT
According to ASME-BPE
2009
2012 DT
According to ASME-BPE
2012
2014 Dt
According to ASME-BPE
2014
DT-15 DT-4.1.2-2 DT-4.1.2-2
TE7WCSW6L - TE7WCSW - Short outlet run Tee
DT-25 DT-4.1.2-3 DT-4.1.2-3
TEG7 - Equal Tee CCC DT-18 DT-4.1.2-4 DT-4.1.2-4
Straight Cross CCCC
TEG7S - Short outlet Tee
DT-18 DT-4.1.2-4
DT-27 DT-4.1.2-5
DT-4.1.2-4
DT-4.1.2-5
TE7RWW - Reducing TEE
TE7RWWCS - short outlet reducing Tee DT-14 DT-4.1.2-7
TEG7R - Reducing TEE
DT-10 DT-4.1.2-6
TEG7RS - Short outlet reducing TEE
DT-19 DT-4.1.2-8
DT-20 DT-4.1.2-9
DT-4.1.2-6
DT-4.1.2-7
DT-4.1.2-8
DT-4.1.2-9
Bio-Pharm Fittings 41
42
Bio-Pharm Fittings
Asme Bpe Dt Index
Drawing Part description
TE7IWWCS - Instrument TEE
2009 DT
According to ASME-BPE
2009
2012 DT
According to ASME-BPE
2012
2014 Dt
According to ASME-BPE
2014
DT-28 DT-4.1.2-10 DT-4.1.2-10
TE31WW - LONG CONCENTRIC REDUCER
TEG71S - Instrument TEE
TE32WW - LONG ECCENTRIC REDUCER
TE31WW - Long concentric reducer
TE31SWW - SHORT CONCENTRIC REDUCER
TE32WW - Long concentric reducer
TE32SWW - SHORT ECCENTRIC REDUCER
TE31SWW - Short concentric reducer
TE31CW - LONG CONCENTRIC REDUCER
TE32SWW - Short eccentric reducer
TE32CW - LONG ECCENTRIC REDUCER
TE31CW - Long concentric reducer
TE31SCW - SHORT CONCENTRIC REDUCER
TE32CW - Long concentric reducer
TE31SCW - Short concentric reducer
DT-29
DT-11
DT-11
N/A
N/A
DT-26
DT-26
N/A
DT-4.1.2-11
DT-4.1.3-1 (a)
DT-4.1.3-1 (a)
DT-4.1.3-1 (b)
DT-4.1.3-1 (b)
DT-4.1.3-2 (a)
DT-4.1.3-2 (a)
DT-4.1.3-2 (b)
DT-4.1.2-11
N/A
N/A
DT-4.1.3-1
DT-4.1.3-1
N/A
N/A
DT-4.1.3-2
EGMO
NEUMO Ehrenberg Group
Asme Bpe Dt Index
Drawing
TE32SCW - SHORT ECCENTRIC REDUCER
Part description
A
TEG31CC - LONG CONCENTRIC REDUCER
TE32SCW - Short eccentric reducer
2009 DT
According to ASME-BPE
2009
2012 DT
According to ASME-BPE
2012
2014 Dt
According to ASME-BPE
2014
N/A DT-4.1.3-2 (b) DT-4.1.3-2
TEG32CC - LONG ECCENTRIC REDUCER
TEG31CC - Long concentric reducer DT-21 DT-4.1.3-3 (a) N/A
DT-21 DT-4.1.3-3 (a) N/A TEG32CC - Long eccentric reducer
TEG31SCC - SHORT CONCENTRIC REDUCER
TEG32SCC - SHORT ECCENTRIC REDCER
TEG31SCC - Short concentric reducer
TEG32SCC - Short eccentric reducer
N/A
N/A
DT-4.1.3-3 (b)
DT-4.1.3-3 (b)
DT-4.1.3-3
DT-4.1.3-3
Clamp ferrule long / Medium / Short
TE16W - Weld cap
TEG16A - Solid end cap
DT-22 DT-4.1.4-1
DT-30 DT-4.1.5-1
DT-31 DT-4.1.5-2
DT-4.1.4-1
DT-4.1.5-1
DT-4.1.5-2
Bio-Pharm Fittings 43
Bio-Pharm Fittings
Bio Fittings
BioConnect® - Clean tube connection
■ Optimized recess contour (patent approved)
■ Highest press-on power at the transitions to wetted areas prevents dirt and germs getting into the sealing space (see ASME-BPE, Ch. SD-3.7.2 and 3.7.6)
■ Defined expansion pockets excludes dangerous “escalator effect” between wetted area and elastomer seat (see ASME-BPE, Ch. SD-3.7.2)
■ Self-draining even after expansion of seal due to high temperature (see
ASME-BPE, Ch. SD-3.7.7)
■ Metal-to-metal-stop avoids stress or overcompression of gaskets (O-ring)
(see ASME-BPE, Ch. SD-3.7.8)
■ Nominal pressure PN16 (D6 - DN100, ½“ - 4”)
44
Connect S® - a unique solution without elastomer gasket
■ Optimal recess contour and design of the sealing metallic surface (patent approved)
■ Excellent cleanability
■ Tested by Fraunhofer-Institut for Grenzflächen-und Bioverfahrenstechnik
■ Hermetic tightness even under repeated temperature changes
■ Defined pre-stressing on the metallic sealing surface
■ No gasket - no elevator effect
■ Protection of the sealing contour against damage
■ Axial positioning by metal-to-metal-stop
■ Exact positioning by central guidance
■ Material grade 1.4435/316 L; other grades on request
■ Wetted areas with roughness Ra<0,8µm (Ra<0,5µm on demand)
■ Dimensions acc. ASME-BPE, DIN11866, DIN 11850,ISO 1127
■ Material Test Report according EN 10204-3.1 (on request ADW 2)
■ Approval for pressure application: issued by TÜV Germany (Süddeutschland)
■ Nominal Pressure: PN 16 (DN 6 until DN 50)
PN 10 (DN 65 until DN 100)
PN 100 (DN 6 until DN 40, high pressure-aseptic connection)
EGMO
NEUMO Ehrenberg Group
Bio Fittings
BioControl®
BioControl® is a fully aseptic modular system with TÜV-approval for pressure application. BioControl® provides the user with a fully hygienic port for connecting control instruments, gauges, sight glasses, etc..., allowing cleaning and sterilizing in place.
BioControl® system is supported by the following manufacturers of instruments and special equipment:
■ Endress + Hauser
■ WIKA
■ LABOM
■ Fisher Rosemount (EMERSON)
■ Papenmeier
■ Others
BioControl® allows 100% Cleaning-In-Place where typical instrument tees stay with uncleaned dead pockets.
Example: Inline - Housing Example: Angle - Housing
Bio-Pharm Fittings 45
46
Bio-Pharm Fittings
Laterals And Manifolds
EGMO offers top quality PCW, CFOS &UHP pre-fabricated laterals & manifolds for the semiconductor industry.
Using EGMO unique 3D internal welding technology dead leg in laterals and manifold POC’s are reduced to minimum:
■ Reduce purge time.
■ Reduce number of welding on-site
■ Reduce cost per line
With new state of the art pre-fabrication plant and clean room facility EGMO offer the best quality laterals & manifolds.
Advantagtes
■ Reducing field installation time by pipe contractor
■ All MP & EP manifold are passivated
■ Custom designed, manufactured, and 100% tested from a single source
■ Reduced assembly & installation costs
■ Warranted as a single part number
■ Advanced and Unique internal welding technology
■ Reduced dead leg in branch
■ Minimum weld per manifold
Egmo laterals application
■ PCW & WFI water loops
■ Bulk Gases distribution systems
■ Specialty gases distribution systems
■ Mini Lateral for hook up
PCW Laterals
304L SCH10
Diameters: 3”- 8”
Material: 304L
Standard: ASTM A312
Manifold outlets
Weld connection
Gland connection
Clamp ferrule
Ball valve
Diaphragm valve
Compression fittings CFOS Laterals
316L
Diameters: 1”-4”
Material: 316L
Standard: ASTM A269/ 270
Applications
Ultra high purity gases
Utility gas line laterals
Process Cooling Water
Short manifolds for gas cabinets UHP - Ultra High Purity
316L EP
Diameters: 1”- 6”
Parker Valves
For UHP gases
EGMO
NEUMO Ehrenberg Group
Customized Components
EGMO, VNE, and NEUMO are distinguished by their unique ability to provide the highest quality stainless steel products - ranging from special fittings, connectors, electro polished vessels and tanks with the most advanced technology, and other special accessories - for a cross-industry clientele.
Our abilities have developed and progressed over the years, allowing us to offer a one-of-a-kind business opportunity: custom stainless steel products and systems, manufactured according to client specifications and needs.
Our Vessels & custom products can be designed to meet any requirement, including vessels, abnormal sizes, special angles, sprinklers, subsystems and many more - all in compliance with industrial regulations.
Bio-Pharm Fittings 47
Bio-Pharm Fittings
Mtr - Material Test Report
The MTR is the reference document for the entire history of the production processes and the raw materials used to make the MaxPure component.
Vendor Warehouse Production Testing Marking Customers
The MTR document is easily generated on-line via MaxPure.net using only the job number as input.
The job number is the product identification number which represents all processes and raw materials related to the specific item.
On-Line MTR
Please, enter job/certificate number:
2084951 CREATE CERTIFICATE
The MTR format provides the following information:
■ Part number, part description and job number
■ Material type
■ Heat Number per each component describing the fitting and its associated properties:
■
■
■
■
Tube dimensions and standards
Chemical composition
Mechanical properties
Visual, dimensional, corrosion, EDDY current testing, flaring and flattening, PMI Test
■ Certificate of Compliance
The MTR is also available for download with
QR CODE
48
EGMO
NEUMO Ehrenberg Group
Technical Information
Pressure service ratings for sanitary stainless steel clamps
Size Tube OD
8”
10”
12”
4”
5”
6”
1 ⁄
2
& 3 ⁄
4
”
1 & 1 1 ⁄
2
”
2”
2 1 ⁄
2
”
3”
13MHHM(-H)
@70°F / 21°C
PSI bar
@250°F / 121°C
PSI bar
1500 103 1200 83
500
450
400
34
31
28
250
250
200
17
17
14
350
200
175
150
24
14
12
10
150
125
100
75
10
9
7
5
100
40
30
7
3
2
50
30
25
3
2
2
Note: The pressure information doesn’t refer to the gaskets.
13MHHS
@70°F / 21°C
PSI bar
@250°F / 121°C
PSI bar
600
550
450
350
250
41
38
31
24
17
300
275
225
160
150
21
19
16
11
10
@70°F / 21°C
PSI bar
13MHP
@250°F / 121°C
PSI bar
1500 103 1200 83
1500
1000
1000
103
69
69
1200
800
800
83
55
55
1000
1000
69
69
800
800
55
55
Gasket Material Properties
Property
Temperature Range
PTFE®
-40 to 450° F
-40 to 232° C
Acid Resistance Excellent
Alkali Resistance
Abrasion Resistance
Compression Set
Excellent
Excellent
Cold flows
VITON®
-20 to 400° F
-29 to 204° C
Good
Poor - good
Good
Good - excellent
SILICON
-80 to 450° F
-62 to 232° C
Good
Poor - fair
Good - excellent
Good - excellent
EPDM
-55 to 275° F
-48 to 135° C
Good - excellent
Good - excellent
Good - excellent
Fair
Conversion Table Of Surface Finishes
Mechanical Finish
µ-in.
µm Grit
32 Ra
24 Ra
20 Ra
12 Ra
0.8 Ra
0.6 Ra
0.5 Ra
0.3 Ra
150
180
240
320
Bio-Pharm Fittings 49
Bio-Pharm Fittings
Technical Information
ASME BPE Table DT-7-1 Hygienic Clamp Ferrule Standard Dimensions and Tolerances
Type A
G
A1
R4
R3
H
Groove Detail
Groove Detail
E
G
D F B
R2
R1
A
C
50
Type B
Type B
(According to the ASME BPE 2014 standard)
E
Groove Detail G
A1
R3
R4 R2
R1
D F B
G
Groove Detail
C
A
EGMO
NEUMO Ehrenberg Group
Industry Terms Glossary
A
Alloy
Term
American Society of
Mechanical Engineers
American Society for the Testing & Materials
Aseptic
ASTM-A 269
ASTM-A 270
B
Bio Processing
Equipment
Bio Processing
Equipment Committee
B31.3 ASME Process
Piping
C
Chemical reaction
Clean in Place
Conductivity
Current Good
Manufacturing
Practice
D
Dead Leg
Deutsches Institut fur Normung
(German Institute for
Standardization)
E
Electron Spectroscopy
for Chemical Analysis
Acronym
ASME
ASTM
-
ASTM-A 269
ASTM-A 270
BPE
BPEC
B31.3
-
-
CIP
cGMP
Definition
A material composed of two or more metals which are mixed and united - usually when they are in a molten state. Alloys are created to improve properties such as the appearance, strength and durability of metals. Common alloys include cast iron, stainless steel, brass, bronze, sterling silver and alpha cellulose, that part of a material made of cellulose that is insoluble in a 17.5% solution of sodium hydroxide at 20°C under specified conditions. While alpha cellulose consists principally of cellulose, it does include other components that are insoluble under the test conditions.
Creates consensus standards for Mechanical Engineering.
Creates consensus standards for material quality and material quality testing methods
Free of pathogenic (disease causing) micro-organisms.
Specification titled “Seamless and Welded Austenitic Stainless Steel Tubing for General Service”.
This specification covers a variety of grades of austenitic stainless steel tubing.
Specification titled “Welded Austenitic Stainless Steel Tubing” for use in the pharmaceutical industries and need to withstand secondary cold forming operations.
This specification covers a variety of grades of austenitic stainless steel tubing.
ASME Standard is intended for the design, materials, construction, inspection and testing of vessels, piping and related process components used in the biopharmaceutical industry and other aseptic applications.
A sub-committee of the ASME BPE Main committee working to develop the ASME BPE standard while meeting three times per year.
American National Standard that covers piping typically found in pharmaceutical, semiconductor, and cryogenic plants, and related processing plants and terminals. It must be noted that B31.3 does not address hygienic tubing and/or piping; it applies mostly to inspection, examination, and testing of systems.
The process by which chemicals combine with each other to form products, which differ from, or alter, the original substances.
The technique of cleaning process line components without the need for disassembly.
Measurement of a substance’s ability to conduct an electric current.
Written and enforced by the FDA. Consists of some specific, but mostly “umbrella” regulations covering personnel, records, and equipment, leaving much to the interpretation of the
Inspector and the court system. cGMP’s are evolutionary, reflecting the least common denominator of practices in the industry at present (hence the term “current”).
-
DIN
ESCA
A section of pipe in a closed recirculation loop that does not have a continuous flow through it.
Creates engineering standards for Germany Contributing body to CEN and ISO.
Other countries and companies give adopted DIN standards.
A procedure that uses electron beams to characterize the extreme outer surface of a metal.
Typically used to determine levels of chromium oxide on the surface of austenitic stainless steel.
Bio-Pharm Fittings 51
52
Bio-Pharm Fittings
Industry Terms Glossary
Term
Electro-Polish
Epidemiology
European Hygienic
Equipment Design
Group
F
Fermentation
Food and Drug
Administration
(USA)
G
Gas Tungsten Arc
Welding
Good Manufacturing
Practices
H
Heat Tracing
I
International Standards
Organization
International
Society for
Pharmaceutical
Engineering
M
Mill Test Report or
Material Test Report
O
Orbital Welding
Ovality
P
Parenteral Drug
Association
Acronym
EP or E/P
-
EHEDG
-
FDA
GTAW
GMP
ISO
ISPE
MTR
-
-
-
PDA
Definition
Polishing process for metal components where the part is placed in an acid bath (typically sulfuric or phosphoric) containing a cathode. As current is passed through the cathode, metal ions are removed from the surface of the metal.
Study of the distribution and determinants of diseases in populations.
Comprised of representatives from research institutes, equipment manufacturers, the food and bio-pharm industry and legislative bodies .
The group’s objective is to provide standardization organizations (CEN and ISO) with specialist views on hygienic and aseptic design by publishing requirements and test methods.
The biochemical synthesis of organic compounds by microorganisms or cultivated cells.
Enforcement agency of the U.S. government for food, drug and cosmetics manufacturing.
Author of the U.S. cGMP’s.
Responsible for new product approvals, plant inspections and product recalls.
(a.k.a. TIG) A welding process where the welding arc is maintained between a non-consumable tungsten electrode and the base metal to be welded. The arc is shielded with an inert gas, typically argon.
Refers specifically to FDA cGMP’s (see cGMP) or to the standards of manufacturing in a particular country and industry (e.g.:EU GMP).
Generally refers to standards that are written and enforced.
Creates consensus standards for engineering and quality systems.
Creates consensus standards for engineering and quality systems.
A global not-for-profit membership organization that provides education, training and technical publications to pharmaceutical manufacturing professionals.
(a.k.a. “Mill Certs”) A document certifying the composition of a metal from a particular heat batch.
An automated TIG (or GTAW) welding process that is designed to produce repeatable fusion welds for tubular components. A system consists of a programmable power supply and weld head. The power supply controls the weld parameters of current and electrode speed. The weld head holds the two parts, purges the weld and moves the electrode using an electric motor.
A quantitative measurement of how ‘round’ a tube is by comparing width to height. Limits are specified on the appropriate ASTM specification of a product.
Association for manufacturers of injectable drug products. Publishes technical reports and other publications of interest to the industry.
EGMO
NEUMO Ehrenberg Group
Industry Terms Glossary
Term
Passivation
Pharmacoepidemiology
Point of Use
Process Qualification/
Process Validation
R
Roughness Average (Ra)
S
Seamless Pipe
Solvent Cleaning
Standard Operating
Procedure
Steam in Place
Sterile
Sulfur
Surface Finish
T
Tubing Dimensions
Tungsten Inert Gas
SOP
SIP
-
-
-
-
Acronym
-
-
POU
PQ/PV
Ra
SF
-
TIG
Definition
The process of rinsing stainless steel with acid (typically nitric) to form a corrosion resistant chromium-oxide layer on the surface.
The study of the utilization and effects of drugs in large numbers of people. To accomplish this study, pharmacoepidemiology borrows from both pharmacology and epidemiology.
A valved branch in a recirculating utility system (typically a water system).
The demonstration and documentation that the various units and procedures of a process operate as they should. This logically establishes that the product is of the quality the system is purported to yield. Performed after the IQ/OQ has been executed and approved. Typically, the acceptance criteria is the same as the product acceptance criteria, and the product run is considered product-for-sale. Executed by the manufacturing personnel of the operating company according to the SOP.
An expression of measured surface roughness or texture, typically, of a polished or machined metal surface. The arithmetic average value of the departure (peaks and valleys) of a surface profile from the center-line throughout the sampling length, generally expressed in microinch(µin) or micro-meter(µm) units and measured with profilometers and/or orescopes.
Pipe produced from a solid billet that is heated and rotated under pressure.
This rotating pressure creates a hole in the middle of the billet, which is then formed into a pipe by a mandrel.
The removal of contaminants such as oil, grease, dirt, salts, etc. by cleaning with a solvent, steam, vapor, alkali, or emulsion.
(a.k.a. EOP, OP) A controlled document that outlines the procedure for operating equipment/ systems. An operator’s adherence to a written SOP is an integral part of the validation process.
It is the connecting link between the initial validation process and the daily manufacturing operation.
Sanitization of process line components by the use of steam without the need for disassembly.
Free of living organisms.
A non-metallic element that exists in several forms-the ordinary one being a yellow, rhombic, crystalline solid-and which burns with a blue flame and a suffocating smell.
Some sulfur compounds, particularly sulphides and oxides, can cause severe chemical deterioration in objects.
Surface finishes are all interior surface finishes accessible and inaccessible, that directly or indirectly come in contact with the designated product in bioprocessing equipment and distribution system components.
Surface roughness specification and measurement standard shall be determined by Ra values rather than by polishing methods.
O.D. - outside diameter
I.D. - inside diameter
Wall thickness or gauge.
All tube dimensions are specific; pipe dimensions are nominal.
Specific - actual measurements in inches.
Nominal - theoretical or stated value of a dimension.
(a.k.a. GTAW) A welding process where the welding arc is maintained between a nonconsumable tungsten electrode and the base metal to be welded. The arc is shielded with an inert gas, typically argon.
Bio-Pharm Fittings 53
Bio-Pharm Fittings
Industry Terms Glossary
Term
U
Ultra Filter or
Ultra-Filtration
Ultraviolet Light or Ultraviolet Radiation
US Pharmaceutical
Class VI-XXII
W
Water For Injection
Welded Tubing
Acronym
UF
UV
USP
WFI
-
Definition
Filters formed from polymer membranes.
UFs have the ability to retain larger molecules while permitting the passage of smaller ones.
Often used for the separation of proteins.
Radiation in the ultraviolet portion of the spectrum (200 to 400 nm) is used to destroy microorganisms. Also used to neutralize ozone.
An official public standards-setting authority for healthcare products manufactured and sold in the United States. USP sets standards for the quality of these products which are also recognized and used outside the United States.
Water for use as a solvent for the preparation of parenteral products conforming to USPXXIII
(EP and JP) guidelines. Obtained most commonly by distillation. However, other processes are allowed depending on particular pharmacopoeia.
Tubular products, which are rolled, formed and then joined continuously along a longitudinal seam by a material fusion process.
The process employed at Gibson Tube is, Gas
Tungsten Arc Welding (GTAW). See Gas
Tungsten Arc Welding’.
54
EGMO
NEUMO Ehrenberg Group
ASME BPE - Certificate
Bio-Pharm Fittings 55
NEUMO EHRENBERG GROUP
G LO B A L LO CAT I O N S
NEUMO GmbH+Co. KG (D)
Tel: +49 (0) 7043 36 0
Fax: +49 (0) 7043 36 179
E-Mail: [email protected]
www.neumo.de
GERMANY
NEUMO-EGMO Spain S.L
Tel: +34 977 524 914
Fax: +34 977 524 898
E-Mail: [email protected]
www.neumo-es.com
SPAIN
VNE Corporation
Tel: +1 800 356 1111
+1 608 756 4930
Fax: +1 608 756 3643
E-Mail: [email protected]
www.vnestainless.com
U.S.A
HPT Inc.
Tel: +845.452.1103
+800.284.4478
E-Mail: [email protected]
http://www.hptinc.com/
U.S.A
NEUMO Polska Sp. z.o.o
Tel: +48 (0) 46 833 4306
Fax: +48 (0) 46 832 5626
E-Mail: [email protected]
POLAND
NEUMO Turkey
Tel: +90 (212) 875 01 41
Fax: +90 (212) 875 23 13
E-Mail: [email protected]
www.neumo.com.tr
TURKEY
NEUMO GmbH + Co. KG
Tel: +84 (4) 3773 6586
Fax: +84 (4) 3773 6587
E-Mail: [email protected]
www.neumo.co.vn
VIETNAM
AWH Armaturenwerke (D)
Hötensleben GmbH
Tel: +49 (0) 39405 92 0
Fax: +49 (0) 39405 92 111
E-Mail: [email protected]
www.awh.de
Damstahl GmbH (D)
Tel: +49 (0) 2173 797 0
Fax: +49 (0) 2173 797 274
E-Mail: [email protected]
www.damstahl.de
Gebr. Rieger GmbH+Co. KG (D)
Tel: +49 (0) 7361 5702 0
Fax: +49 (0) 7361 5702 51
E-Mail: [email protected]
www.rr-rieger.de
GERMANY
NEUMO-VARGUS (Shanghai)
Trading Co., Ltd
Tel: +86 (21) 54178180
Fax: +86 (21) 54178190
E-Mail: [email protected]
CHINA
NEUMO
Tel: +353 (0)21 4975540
Cel: +353 (0)87 2330469
E-Mail: [email protected]
www.neumo.de/en/
IRELAND
Damstahl a/s Oslo (N)
Tel: +47 5615 1570
Fax: +47 5615 1571
E-Mail: [email protected]
www.damstahl.no
NORWAY
EGMO Ltd.
Tel: +972 (0) 4 9855 176
+972 (0) 4 9855 111
Fax: +972 (0) 4 9855 175
E-Mail: [email protected]
www.egmo.co.il
ISRAEL
Herrli AG
Tel: +41 (0) 31 750 12 11
Fax: +41 (0) 31 750 12 00
E-Mail: [email protected]
www.herrli.net
SWITZERLAND
NEUMO Budapest Kft
Tel: +36 (1) 3174177
+36 (1) 3185982
Fax: +36 (1) 266 8765
E-Mail: [email protected]
www.neumo.hu
HUNGARY
NEUMO UK Ltd.
Tel: +44 (0) 1952 583 999
Fax: +44 (0) 1952 583 958
E-Mail: [email protected]
www.neumo.co.uk
UNITED KINGDOM
Damstahl a/s (Denmark)
Tel: +45 (0) 8794 4000
Fax: +45 (0) 8794 4150
E-Mail: [email protected]
www.damstahl.dk
DENMARK
Damstahl a/b (Sweden)
Tel: +46 87 61 71 00
Fax: +46 87 61 14 05 www.damstahl.se
SWEDEN
Bio-Pharm Hygienic
advertisement
Related manuals
advertisement