Krone BA EasyCut F 320 CV gez./ges. Operating Instructions


Add to my manuals
144 Pages

advertisement

Krone BA EasyCut F 320 CV gez./ges. Operating Instructions | Manualzz

Original operating instructions

Document number: 150000173_08_en-gb

Version: 13/08/2021

Front mounted mowers

EasyCut F 320 CV

From machine number: 1078670

Contact

Maschinenfabrik Bernard Krone GmbH & Co. KG

Heinrich-Krone-Straße 10

48480 Spelle

Germany

Telephone main office

Telefax main office

Telefax spare parts warehouse national territory

+ 49 (0) 59 77/935-0

+ 49 (0) 59 77/935-339

+ 49 (0) 59 77/935-239

Telefax spare parts warehouse export + 49 (0) 59 77/935-359

Internet www.landmaschinen.krone.de

https://mediathek.krone.de/

Information for enquiries and orders

Year

Machine number

Type

Contact data of your dealer

2

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2

2.4.10

2.4.11

2.4.12

2.4.13

2.4.14

2.4.15

2.4.16

2.4.17

2.4.18

2.4.19

2.4.20

2.5

2.5.1

2.5.2

2.5.3

2.6

2.7

2.8

2.1

2.2

2.3

2.4

2.4.1

2.4.2

2.4.3

2.4.4

2.4.5

2.4.6

2.4.7

2.4.8

2.4.9

1

1.1

1.2

1.3

1.4

1.5

1.5.1

1.5.2

1.5.3

1.5.4

1.5.5

1.5.6

1.5.7

4

4.1

4.2

4.3

4.4

4.5

4.6

4.7

4.8

3

3.1

3.2

3.3

3.4

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Table of contents

Information on This Document.................................................................................................  6

Validity .........................................................................................................................................  6

Re-ordering ..................................................................................................................................  6

Applicable documents..................................................................................................................  6

Target group of this document .....................................................................................................  6

How to use this document ...........................................................................................................  6

Directories and references...........................................................................................................  6

Information on direction ...............................................................................................................  7

Term “machine”............................................................................................................................  7

Figures .........................................................................................................................................  7

Scope of the document ................................................................................................................  7

Means of representation ..............................................................................................................  7

Conversion table ..........................................................................................................................  9

Safety ........................................................................................................................................  12

Intended use ..............................................................................................................................  12

Reasonably foreseeable misuse................................................................................................  12

Service life of the machine.........................................................................................................  13

Basic safety instructions ............................................................................................................  13

Importance of operating instructions..........................................................................................  13

Personnel qualification of the operating personnel ....................................................................  13

Personnel qualification of the technicians..................................................................................  14

Children in danger .....................................................................................................................  14

Connecting the machine ............................................................................................................  14

Structural modifications on the machine ....................................................................................  14

Additional equipment and spare parts .......................................................................................  14

Jobs on the machine..................................................................................................................  15

Operational safety: Technically sound condition .......................................................................  15

Danger zones ............................................................................................................................  16

Ensuring functionality of safety devices .....................................................................................  18

Personal protective equipment ..................................................................................................  18

Safety markings on the machine ...............................................................................................  19

Road safety................................................................................................................................  19

Parking the machine safely .......................................................................................................  20

Consumables .............................................................................................................................  20

Dangers arising from environment.............................................................................................  21

Sources of danger on the machine ............................................................................................  22

Dangers in connection with certain activities: Working on the machine ....................................  23

Behaviour in dangerous situations and in case of accidents .....................................................  24

Safety routines ...........................................................................................................................  24

Shutting down and safeguarding the machine...........................................................................  24

Securing raised machine and machine parts against lowering..................................................  25

Carrying out oil level check and oil and filter element changes safely.......................................  25

Safety Labels on the Machine ...................................................................................................  26

Information labels on the machine .............................................................................................  35

Safety features...........................................................................................................................  43

Machine Description................................................................................................................  45

Machine overview ......................................................................................................................  45

Overload protections on the machine ........................................................................................  47

Labelling ....................................................................................................................................  47

Intermediate universal shaft.......................................................................................................  48

Technical data ..........................................................................................................................  49

Dimensions ................................................................................................................................  49

Weights ......................................................................................................................................  49

Area output ................................................................................................................................  49

Cutting height.............................................................................................................................  49

Technically permitted maximum speed (road travel) .................................................................  49

Airborne noise emission ............................................................................................................  49

Ambient temperature .................................................................................................................  50

Requirements for tractor - power ...............................................................................................  50

3

Table of contents

6

6.1

6.2

6.2.1

6.2.2

6.3

6.4

4.9

4.10

4.11

4.12

4.12.1

4.12.2

5

5.1

8

8.1

8.1.1

8.1.2

8.2

8.2.1

8.2.2

8.3

8.3.1

8.3.2

7

7.7

7.8

7.9

7.10

7.11

7.12

7.13

7.14

7.15

7.16

7.1

7.2

7.3

7.4

7.5

7.6

8.4

8.4.1

8.4.2

8.5

8.6

8.7

8.8

8.9

8.10

9

9.1

9.2

9.3

9.3.1

9.3.2

4

Tractor requirements – hydraulics .............................................................................................  50

Requirements for the tractor – electrics .....................................................................................  50

Machine equipment ...................................................................................................................  50

Consumables .............................................................................................................................  50

Oils.............................................................................................................................................  51

Lubricating greases ...................................................................................................................  51

Control and Display Elements ................................................................................................  52

Hydraulic control units of the tractor ..........................................................................................  52

Commissioning ........................................................................................................................  53

Checklist for initial operation ......................................................................................................  53

universal shaft............................................................................................................................  54

Adapting universal shaft ............................................................................................................  54

Mounting the universal shaft on the machine ............................................................................  55

Mounting lighting system ...........................................................................................................  55

Adapting coupling points............................................................................................................  56

Start-up .....................................................................................................................................  60

Calculating the ballasting of the tractor-machine combination ..................................................  60

Preparing tractor ........................................................................................................................  63

Mounting top link fork.................................................................................................................  64

Connecting machine to tractor ...................................................................................................  65

Mounting lower link extension....................................................................................................  66

Checking/setting parallel lifting ..................................................................................................  67

Mounting relief springs...............................................................................................................  68

Connecting hydraulic hoses.......................................................................................................  71

Connecting road travel lighting ..................................................................................................  72

Connect the Camera Monitor System........................................................................................  73

Tightening guard cloth ...............................................................................................................  74

Installing universal shaft ............................................................................................................  74

Checking front end dimension ...................................................................................................  75

Checking locking device and latch.............................................................................................  76

Checking the tines on the tine conditioner .................................................................................  76

Basic setting of mower...............................................................................................................  77

Operation ..................................................................................................................................  79

Front guard ................................................................................................................................  79

Folding up the front guard..........................................................................................................  79

Fold down the front guard ..........................................................................................................  80

Side guard - for the “series” version ..........................................................................................  80

Folding up the side guard - for "Series" version (transport position)..........................................  81

Folding down the side guard - for "Series" version (working position).......................................  81

Side guard - for version with “hydraulically folding side guards”................................................  81

Folding up the side guard – in version "hydraulically folding side guards" (transport position) .  82

Folding down the side guard – in version "hydraulically folding side guards" (working position)

...................................................................................................................................................  82

Operating support jack...............................................................................................................  82

Moving support jack into transport position ...............................................................................  83

Moving support jack into support position..................................................................................  83

Locking/releasing stop cock.......................................................................................................  84

Operating the stop cock .............................................................................................................  84

Lowering machine from transport position to working position ..................................................  85

Raising machine from working position to transport position.....................................................  85

Field mode .................................................................................................................................  86

Operating the Camera Monitor System .....................................................................................  87

Driving and Transport .............................................................................................................  88

Preparing the machine for road travel .......................................................................................  89

Parking the machine ..................................................................................................................  90

Preparing the machine for shipment ..........................................................................................  91

Checklist for the transport of the machine .................................................................................  92

Lifting the machine.....................................................................................................................  92

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Table of contents

9.3.3

12

12.1

12.2

13

13.1

13.2

13.3

11

11.1

11.1.1

11.1.2

11.1.3

11.1.4

11.1.5

11.1.6

11.2

11.3

11.4

11.5

11.6

11.7

11.7.1

11.7.2

11.7.3

11.7.4

11.7.5

10

10.1

10.2

10.3

10.4

10.5

10.6

10.7

10.8

10.9

10.10

10.11

15

15.1

15.2

16

16.1

14

14.1

14.2

14.2.1

14.2.2

14.2.3

14.3

14.4

17

Lashing the machine..................................................................................................................  93

Settings.....................................................................................................................................  94

Setting the cutting height ...........................................................................................................  94

Telescopic top link .....................................................................................................................  95

Adjusting the relief spring(s) ......................................................................................................  96

Increasing/reducing ground pressure – mechanical relief adjustment.......................................  98

Increasing/reducing the ground pressure – hydraulic relief adjustment ....................................  99

Setting the side guards ............................................................................................................  100

Setting conditioner speed ........................................................................................................  101

Setting the degree of conditioning ...........................................................................................  101

Setting swath width ..................................................................................................................  102

Setting wide spreading ............................................................................................................  103

Configure/check the Camera Monitor System .........................................................................  103

Maintenance - General Information......................................................................................  105

Maintenance table ...................................................................................................................  105

Maintenance – Before the season ...........................................................................................  105

Maintenance – After the season ..............................................................................................  106

Maintenance - Once after 50 hours .........................................................................................  106

Maintenance - Every 10 hours, but at least once a day...........................................................  107

Maintenance - Every 50 hours .................................................................................................  107

Maintenance - Every 200 hours ...............................................................................................  107

Tightening torques ...................................................................................................................  107

Deviating tightening torques ....................................................................................................  110

Venting the friction clutch.........................................................................................................  111

Checking guard cloths .............................................................................................................  113

Cleaning the machine ..............................................................................................................  114

Drive belt..................................................................................................................................  114

Dismounting/mounting guard ...................................................................................................  114

Tensioning/relieving belt drive .................................................................................................  115

Checking/setting belt tension ...................................................................................................  116

Checking drive belt for damage ...............................................................................................  117

Replacing drive belt .................................................................................................................  117

Maintenance - Hydraulic System..........................................................................................  118

Hydraulic oil .............................................................................................................................  119

Checking hydraulic hoses ........................................................................................................  119

Maintenance - Gearbox .........................................................................................................  120

Overview of gearboxes ............................................................................................................  120

Input gearbox ...........................................................................................................................  121

Main gearbox ...........................................................................................................................  123

Maintenance - Cutterbar........................................................................................................  125

Rotary hub ...............................................................................................................................  126

Check/change blades ..............................................................................................................  127

Checking the blade for wear ....................................................................................................  127

Changing blades for the “blade screw connection” version .....................................................  128

Changing blades for the “blade quick fastener” version ..........................................................  129

Checking/replacing linings on cutterbar ...................................................................................  130

Checking oil level .....................................................................................................................  131

Maintenance – Lubrication....................................................................................................  133

Lubricating universal shaft .......................................................................................................  134

Lubrication chart – Machine.....................................................................................................  135

Malfunction, cause and remedy ...........................................................................................  136

General disturbances...............................................................................................................  136

Waste disposal.......................................................................................................................  137

Index........................................................................................................................................  138

Declaration of conformity .....................................................................................................  143 18

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 5

1

1.1

1

Information on This Document

Validity

Information on This Document

1.1

1.2

1.3

1.4

1.5

1.5.1

Validity

This document is valid for machines of type:

EasyCut F 320 CV

All information, illustrations and technical data in this document correspond to the latest state at the time of publication.

We reserve the right to make design changes at any time and without notification of reasons.

Re-ordering

You can request a replacement document if this document became completely or partly unusable, or if you need it in a different language. Please specify the document number shown on the cover page in your order. Alternatively, you can download the document online from

KRONE MEDIA https://media.krone.de

.

Applicable documents

To ensure that the machine is used safely and as intended, observe the following further applicable documents.

• Operating instructions for universal shaft

• Assembly instructions, KRONE

• Spare parts list, KRONE

Target group of this document

This document aims at the operator of the machine who fulfills the minimum requirements of personnel qualification,

see Page 13 .

How to use this document

Directories and references

Contents/headers

The contents and headers in this document ensure quick orientation in the chapters.

Index

The index contains catchwords in alphabetical order which enable to find information on a desired topic easily. The index can be found on the last pages of this document.

Cross references

Cross references to another place in the document or to another document are in the text with page number.

6

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

1.5.2

1.5.3

1.5.4

1.5.5

1.5.6

Information on This Document

How to use this document

Examples:

Check the tight seat of all screws on the machine, see Page 7

. ( INFO : If you use an electronic version of this document, click on the link to go to the specified page.)

• For further information, refer to the operating instructions of the universal shaft manufacturer.

1

1.5

Information on direction

Directional information in this document, such as front, rear, right and left, applies in the direction of travel of the machine.

Term “machine”

Throughout the rest of this document, the “front mounted mower” will also be referred to as the

“machine”.

Figures

The figures in this document do not always represent the exact machine type. The information that refers to the figure always corresponds to the machine type of this document.

Scope of the document

In addition to standard equipment, accessories kits and versions of the machine are described in this document. Your machine may deviate from this document.

Means of representation

Icons in the text

The following means of representation (icons) are used to present the text more clearly:

This arrow characterizes an action step . Several arrows in a row identify a sequence of actions to be performed step by step.

This icon identifies a prerequisite that has to be fulfilled to perform an action step or a sequence of actions.

This arrow marks the intermediate result of an action step.

This arrow identifies the result of an action step or sequence of actions.

This bullet point identifies an enumeration . If the bullet point is intended, it identifies the second level of the enumeration.

Icons in figures

The following icons can be used in illustrations:

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 7

8

1

1.5

Information on This Document

How to use this document

Icon

1

X

LH

Explanation

Reference sign for part

Icon

I

Dimensions (e. g. also W = width,

H = height, L = length)

Left side of machine

Direction of travel

Reference line for visible material

RH

Centre line

Open

Apply liquid lubricant (e.g. lubricating oil)

Explanation

Position of a part (e.g. move from position I to position II)

Magnification of display detail

Right side of machine

Direction of motion

Reference line for covered material

Cable routes

Closed

Apply lubricating grease

Warning signs

Warnings of dangers are separated from the remaining text as warning signs and are identified with a danger sign and signal words.

The warning signs must be read and the measures must be observed in order to prevent personal injury.

Explanation of danger sign

This is the danger sign that warns of a risk of injury.

Please observe all notes marked with the danger sign in order to avoid injuries or death.

Explanation of signal words

DANGER

The signal word DANGER warns of a hazardous situation which will result in serious injuries or death if the warning sign is ignored.

WARNING

The signal word WARNING warns of a hazardous situation which will result in serious injuries or death if the warning sign is ignored.

CAUTION

The signal word CAUTION warns of a hazardous situation which will result in minor to moderate injuries if the warning sign is ignored.

Example of a warning sign:

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

1.5.7

Information on This Document

How to use this document

1

1.5

WARNING

Eye damage caused by flying dirt particles

When cleaning with compressed air, dirt particles are ejected at high speed and could get into the eyes. Therefore eyes could be hurt.

„ Keep people away from the working area.

„ Wear personal protective equipment when performing cleaning work with compressed air

(e.g. eye protection).

Warnings of property damage/environmental damage

Warnings of property/environmental damage are separated from the remaining text and marked with "Notice".

Example:

NOTICE

Gearbox damage due to low oil level

The gearboxes could be damaged when the oil level is too low.

„ Check gear oil level at regular intervals and top up oil, if necessary.

„ Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check oil level only when machine is in horizontal position.

Notes with information and recommendations

Additional information and recommendations for trouble-free and productive operation of the machine are separated from the remaining text and marked with “Information”.

Example:

INFO

Each safety label is provided with an order number and can be ordered directly from the manufacturer or from the authorized specialist dealer.

Conversion table

The following table can be used to convert metric units into US units.

Size

Area

Volume flow Litres per minute L/min

Cubic metres per hour m³/h

Force

Length

Power

SI units (metric)

Unit name Abbreviation

Hectare ha

Newton

Millimetre

Metre

Kilowatt

N mm m kW

Factor

2.47105

0.2642

4.4029

0.2248

0.03937

3.2808

1.3410

Inch-pound units

Unit name

Acre

US gallons per minute

Pound force

Inch

Foot

Horsepower

Abbreviation acres gpm lbf in.

ft.

hp

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 9

1

1.5

Information on This Document

How to use this document

Size

Pressure

Torque

SI units (metric)

Unit name Abbreviation

Kilopascal kPa

Megapascal bar (non-SI)

Newtonmeter

MPa bar

Nm

Factor

0.1450

145.0377

14.5038

0.7376

Temperature Degrees Celsius °C

Velocity

Volumes

Weight

Metres per minute

Metres per second

Kilometres per hour

Litres

Millilitre

Cubic centimetre

Kilogram m/min m/s km/h

L ml cm³ kg

8.8507

°Cx1.8+32

3.2808

3.2808

0.6215

0.2642

0.0338

0.0610

2.2046

Inch-pound units

Unit name Abbreviation

Pounds per square inch psi pound-foot or foot-pound ft∙lbf pound-inch or inch-pound

Degrees

Fahrenheit in∙lbf

°F

Feet per minute ft/min

Feet per second ft/s

Miles per hour mph

US gallon

US ounce

Cubic inch

US gal.

US oz.

in³

Pound lbs

10

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

This page has been left blank deliberately.

Information on This Document

How to use this document

1

1.5

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 11

2

2.1

2

Safety

Intended use

Safety

2.1

2.2

Intended use

This machine is a mower and is used to mow crops.

The crops designated for the intended use of this machine are stalk and leaf crops growing on the ground.

The machine is designed exclusively for use in agriculture and may only be used when

• all safety devices are available according to the operating instructions and are located in the protective position.

• all safety instructions of the operating instructions have been observed and complied with,

both in chapter “Basic safety instructions”, see Page 13 , and directly in the chapters of the

operating instructions.

The machine may be used only by people who satisfy the personnel qualification requirements

designated by the machine manufacturer, see Page 13

.

These operating instructions are part of the machine and must therefore be at hand when the machine is in use. The machine may be operated only when the operator has received training and in compliance with these operating instructions.

If the machine is used for applications which are not described in these operating instructions, this may result in serious injuries or death and damage to the machine and other property.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt the proper operation. For this reason, unauthorised modifications shall exclude any liability of the manufacturer for consequential damage.

The intended use shall also include the adherence to the operating, maintenance and repair conditions set by the manufacturer.

Reasonably foreseeable misuse

Any use beyond the intended use

see Page 12 is regarded as improper use and is therefore

misuse according to the Machinery Directive. The manufacturer is not liable for damage resulting from this, the user alone bears the risk.

Such misuse is for example:

Processing of crops which are outside the intended use of the machine, see Page 12

• Transport of people

• Transport of goods

• Exceeding the permitted technical gross weight

• Non-compliance with the safety labels on the machine and safety notes in the operating instructions

• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the information in the operating instructions

• Unauthorised modifications to the machine

• Attachment of unauthorised or unapproved additional equipment

• Use of spare parts which are not KRONE original spare parts

• Stationary operation of the machine

Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper operation. For this reason, unauthorised modifications will exclude any liability of the manufacturer for consequential damage.

12

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.3

2.4

2.4.1

2.4.2

Safety

Service life of the machine

Service life of the machine

• The service life of this machine depends on its proper operation and maintenance as well as the operating and harvesting conditions.

• By heeding the instructions and information in these operating instructions, permanent operational readiness and a long service life of the machine can be achieved.

• After each operating season, inspect the entire machine for wear and other damage.

• Replace damaged and worn components before recommissioning the machine.

• Carry out a full technical inspection of the machine after five years of machine operation and make a decision on further machine usage taking the results of this inspection into account.

• Theoretically, the service life of this machine is unlimited as all worn or damaged components can be replaced.

2

2.3

Basic safety instructions

Non-compliance with the safety instructions and warnings

Non-compliance with the safety instructions and warnings may result in injuries and damage to the environment and property.

Importance of operating instructions

The operating instructions are an important document and a part of the machine. They are intended for the user and contain information that is relevant to safety.

Only the procedures specified in the operating instructions are safe. If the operating instructions are not followed, there is a risk of serious or even fatal injuries.

„ Prior to using the machine for the first time, read and observe the "Basic safety notices" completely.

„ Prior to starting work, read and observe the respective sections in the operating instructions too.

„ Keep the operating instructions ready to hand for the user of the machine in the document storage tube,

see Page 45 .

„ Hand over the operating instructions to subsequent users.

Personnel qualification of the operating personnel

If the machine is not used properly, people may be seriously injured or killed. To avoid accidents, each person who works with the machine must satisfy the following minimum requirements:

• He is physically capable of controlling the machine.

• He can work safely with the machine in accordance with these operating instructions.

• He understands the method of operation of the machine within the scope of his work and can identify and avoid the dangers associated with the work.

• He has read the operating instructions and can implement the information in the operating instructions accordingly.

• He is familiar with driving vehicles safely.

• For road travel he has adequate knowledge of the highway code and has the stipulated driving licence.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 13

2

2.4

2.4.3

Safety

Basic safety instructions

Personnel qualification of the technicians

If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed improperly on the machine, people may be seriously or fatally injured. To avoid accidents, everyone who performs work according to these instructions must meet the following minimum requirements:

• Qualified professional, with relevant training.

• Capable of assembling the (partially) disassembled machine according to the assembly instructions provided by the manufacturer.

• He is capable, e.g. by attending a training course, of extending, modifying or repairing the function of the machine according to the relevant instructions provided by the manufacturer.

• He has read the operating instructions and can implement the information in the operating instructions accordingly.

• Ability to perform the work safely according to these instructions.

• Understands the mode of operation of the work to be performed and the machine and is able to identify and avoid risk in carrying out the necessary work.

• Has read these instructions and is able to implement the information explained in these instructions accordingly.

2.4.4

Children in danger

Children are not in a position to assess dangers and behave unpredictably.

Thus children are particularly at risk.

„ Keep children away from the machine.

„ Keep children away from consumables.

„ Make sure that there are no children in the danger zone, especially when starting and triggering machine movements.

2.4.5

2.4.6

2.4.7

14

Connecting the machine

When tractor and machine are not correctly connected, there is a risk of causing serious accidents.

„ When connecting, follow all operating instructions:

• the operating instructions of the tractor

the operating instructions of the machine, see Page 60

• the operating instructions of universal shaft

„ Observe the changed driving behaviour of the combination.

Structural modifications on the machine

Structural modifications and extensions that were not approved by KRONE can impair the functionality, operational safety and also the road traffic certification of the machine. As a result, persons can be seriously injured or killed.

Any structural modifications and extensions that are not authorised by KRONE are not permitted.

Additional equipment and spare parts

Additional equipment and spare parts that do not correspond to the requirements of the manufacturer may affect the operational safety of the machine and cause accidents.

„ To ensure operational safety, use original parts or standard parts which correspond to the requirements of the manufacturer.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.4.8

2.4.9

Safety

Basic safety instructions

2

2.4

Jobs on the machine

Passengers

Passengers may be seriously injured by the machine or fall off the machine and run over.

Ejected objects may strike and injure passengers.

„ Never carry passengers on the machine.

Operational safety: Technically sound condition

Operation only after proper commissioning

The operational safety of the machine is not guaranteed without proper commissioning in accordance with these operating instructions. This may result in accidents and people may be seriously or fatally injured.

„ Use the machine only after proper commissioning,

see Page 60 .

Technically sound state of the machine

Improper maintenance and setting could influence the operational safety of the machine and cause accidents. Thus there is a risk of serious injuries or death.

„ All maintenance and setting work must be performed according to the chapters

“Maintenance and Setting”.

„ Before performing any maintenance and setting work, shut down and safeguard the machine,

see Page 24

.

Danger resulting from damage to the machine

Damage to the machine may impair the operational safety of the machine and cause accidents.

As a result, people may be seriously injured or killed. The following parts of the machine are particularly important for safety:

• Safety Devices

• Connecting devices

• Lighting

• Hydraulics

• Universal shaft

If there are doubts about the operational safety of the machine, for example due to an unexpected change to the operational behaviour, visible damage or leaking consumables:

„

Shut down and safeguard the machine, see Page 24

.

„ Immediately eliminate potential causes of damage, for example heavy soiling, or tighten slack screws.

„ In case of damage which may affect operational safety and cannot be repaired according to these operating instructions: Have damage repaired by a qualified service centre.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 15

2

2.4

Safety

Basic safety instructions

Technical limit values

If the technical limit values of the machine are not observed, the machine may be damaged. As a result, accidents may occur and people may be seriously or fatally injured. With regard to safety, it is especially important to observe the following technical limit values:

• maximum permitted operating pressure of the hydraulics

• maximum permitted drive speed

• maximum permitted axle loads of the tractor

• maximum permitted transport height and width

„

Comply with limit values, see Page 49 .

2.4.10

Danger zones

If the machine is switched on, its surrounding can present a danger zone.

Avoid entering the danger zone of the machine by observing the minimum safety distance.

If the safety distance is not observed, people may be seriously injured or killed.

„ Do not switch on the drives and engine if the minimum safety distance has not been observed.

„ If people fail to observe the minimum safety distance, switch off the drives.

„ Switch the machine off in shunting and field mode.

The safety distance is:

For machine in shunting and field mode

In front of the machine

Behind the machine

On either side of the machine

30 m

5 m

3 m

For machine switched on without driving motion

In front of the machine 3 m

Behind the machine 5 m

On either side of the machine 3 m

The safety distances specified here are minimum distances in terms of intended use. If necessary, these safety distances must be increased according to the operating and ambient conditions.

„ Before working in front of and behind the tractor and in the danger zone of the machine:

Shut down and secure the machine, see Page 24 . This also applies to brief inspection

work.

„ Consider the information in all relevant operating instructions:

• the operating instructions for the tractor

• the operating instructions of the machine

• the operating instructions of universal shaft

Danger zone universal shaft

People may be caught, pulled in and seriously injured by the universal shaft.

„ Observe operating instructions of universal shaft.

„ Ensure sufficient overlap of section tube and universal shaft guards.

„ Make sure that the universal shaft guards are mounted and that they are fully functional.

16

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Basic safety instructions

„ Allow the universal shaft locks to engage. There must be no areas of the locking device on the PTO shaft fork which could cause catching or entrapment (e.g. by annular design, protective collar around the locking pin).

„ Attach chains to prevent the universal shaft guards from rotating with the shaft.

„ Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

„ Ensure that the selected speed and direction of rotation of the PTO shaft of the tractor match the permitted speed and direction of rotation of the machine.

„ Switch off the PTO shaft when the angles between the universal shaft and the PTO shaft are too large. The machine may be damaged. Parts may be hurled up and cause injury to people.

2

2.4

Danger zone PTO shaft

People may be caught, pulled in and seriously injured by the PTO shaft and the driven components.

Before switching on the PTO shaft:

„ Ensure that all protective devices are mounted and brought into protective position.

„ Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

„ Switch off drives if they are not needed.

Danger zone between tractor and machine

People standing between the tractor and machine may be seriously injured or killed if the tractor rolls away or by carelessness or machine movements:

„ Before carrying out any work between the tractor and the machine: Always turn off and

secure the machine, see Page 24

. This also applies to brief inspection work.

„ If the lifting device must be actuated, instruct all people to keep away from the range of movement of the lifting device.

Danger zone ejected objects

Crops and foreign bodies may be forcefully flung out and injure or kill people.

„ Before starting the machine, instruct all people to leave the danger zone of the machine.

„ If people are in the danger zone of the machine, immediately switch off drives and diesel engine.

Danger zone when drive is switched on

When the drive is switched on, there is a danger to life caused by rotating machine parts.

Ensure that there are no persons in the danger zone of the machine.

„ Before starting the machine, instruct all people to leave the danger zone of the machine.

„ In case of dangerous situations, immediately switch off drives and instruct people to leave the danger zone.

Danger zone due to trailing machine parts

If machine parts are trailing, people may be seriously injured or killed.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 17

2

2.4

Safety

Basic safety instructions

After the drives have been switched off, the following machine parts will trail:

• Universal shafts

• Cutting discs

• Conditioner

• Conveying devices

„

Shut down and safeguard the machine, see Page 24

.

„ Do not attempt to approach the machine until all moving machine parts have come to a standstill.

2.4.11

Ensuring functionality of safety devices

If safety devices are missing or damaged, people may be seriously injured or killed by moving machine parts.

„ Replace damaged safety devices.

„ Mount dismounted safety devices and machine parts again before start-up and move them to protective position.

„ If it is doubtful whether all safety devices have been correctly installed and are functional, have a service centre check them.

Keeping universal shaft guard functional

The overlap of universal shaft and protective cap on the machine must not be less than 50 mm.

This minimum overlap is also required for protective devices of wide-angle universal shaft and if couplings or other components are used. If the operator has to reach between the universal shaft guard and the protective cap to connect the universal shaft, the clearance on one level must be at least 50 mm. On all levels the clearance must be no more than 150 mm.

2.4.12

Personal protective equipment

The wearing of personal protective equipment is an important safety measure. Missing or unsuitable personal protective equipment increases health risks and injuries.

Personal protective equipment includes, for example:

• Suitable protective gloves

• Safety shoes

• Tight-fitting protective clothing

• Hearing protection

• Protective goggles

• If dust is generated: appropriate breathing protection

„ Specify and provide personal protective equipment for the particular job.

„ Use only personal protective equipment which is in proper condition and offers effective protection.

„ Adjust personal protective equipment to the person, for example the size.

„ Remove unsuitable clothing and jewellery (e.g. rings, necklaces) and cover long hair with a hairnet.

18

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.4.13

2.4.14

Safety

Basic safety instructions

2

2.4

Safety markings on the machine

Safety labels on the machine warn of hazards at danger points and are an important component of the machine's safety equipment. Missing safety labels increase the risk of serious and fatal injuries.

„ Clean dirty safety labels.

„ After each cleaning, check to ensure that the safety labels are complete and legible.

„ Immediately replace missing, damaged and unrecognisable safety labels.

„ Label spare parts with the required safety labels.

Descriptions, explanations and order numbers of the safety labels,

see Page 26 .

Road safety

Dangers during road travel

Other road users can be put at risk when you drive on public roads and the machine is not properly illuminated and/or exceeds the maximum dimensions and weights laid down by national law.

„ Prior to driving on public roads, ensure that the maximum permissible dimensions, weights and axle, support and trailer loads are not exceeded which are applicable under national law for driving on public roads.

„ Before driving on roads, switch on the road travel lighting and ensure that it functions properly.

„ Before driving on roads, close all stop cocks for the hydraulic supply to the machine between tractor and machine.

„ Before driving on roads, move the tractor control units to the neutral position and lock them.

Danger when driving on road and field

Hitched and mounted machines change the handling characteristics of the tractor. The handling characteristics depend for instance on operating state and ground. If changed handling characteristics are not considered, the driver may cause accidents.

„ Observe measures for driving on road and field,

see Page 88 .

Dangers if the machine is not prepared properly for road travel

If the machine is not prepared properly for road travel, serious accidents may occur with traffic.

„ Before driving on roads, prepare the machine for road travel,

see Page 89

.

Danger when cornering with a hitched machine and due to the overall width

Accidents may occur when cornering due to the machine swinging out and also due to the overall width.

„ Consider the overall width of the combined tractor and machine.

„ Consider the larger swivel range when cornering.

„ Consider people, oncoming traffic and obstacles when turning.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 19

2

2.4

Safety

Basic safety instructions

Dangers when operating the machine on slopes

The machine may tilt when it is used on slopes. As a result, accidents may occur and people may be seriously injured or killed.

„ Do not work and drive on a slope unless the ground of the slope is flat and the adhesion of the tyres to the ground is ensured.

„ Turn the machine at low speed. Turn in a large arc.

„ Avoid driving across a slope because the centre of gravity of the machine will be changed by payload and by executing machine functions.

„ Avoid abrupt steering movements on slopes.

„ Do not move the machine from working position to transport position or from transport position to working position as long as the machine is used across a slope.

„ Do not park the machine on slopes.

2.4.15

Parking the machine safely

An incorrectly parked and insufficiently safeguarded machine can represent a danger for people, especially children, and can be set into motion or fall over in an uncontrolled manner.

People may be injured or killed.

„ Park the machine on a horizontal and level ground capable of bearing the load.

„ Before adjusting, repairing, servicing and cleaning the machine, ensure that it is securely positioned.

„ Observe section “Parking the Machine” in chapter Driving and Transport.

see Page 90

„ Before parking: Shut down and safeguard the machine,

see Page 24

.

2.4.16

Consumables

Unsuitable consumables

Consumables which do not comply with the requirements of the manufacturer may impair the operational safety of the machine and cause accidents.

„ Use only consumables which comply with the requirements of the manufacturer.

For requirements on consumables,

see Page 50

.

Contamination of hydraulic system and/or fuel system

Foreign objects and/or liquids in the hydraulic system and/or fuel system may impair the operational safety of the machine and cause accidents.

„ Clean all connections and components.

„ Close open connections by means of protective caps.

20

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.4.17

Safety

Basic safety instructions

Environmental protection and disposal

Consumables such as diesel fuel, brake fluid, antifreeze and lubricants (e.g. gearbox oil, hydraulic oil) may damage the environment and the health of people.

„ Do not release consumables into the environment.

„ Fill consumables in a liquid-tight labelled container and dispose of according to the official regulations.

„ Absorb leaked consumables with an absorbent material, fill them in a liquid-tight labelled container and dispose of according to the official regulations.

2

2.4

Dangers arising from environment

Fire hazard

Combustible materials may accumulate in the machine due to operation or animals, such as rodents or nesting birds, or dust resuspension.

In case of dry usage conditions, dust, impurities and crop residue may ignite on hot parts and the resulting fire may seriously injure or kill people.

„ Check and clean the machine every day before using it for the first time.

„ Check and clean the machine regularly during the working day.

Behavior in the case of voltage flashover of overhead lines

High electric voltage may be applied to electrically conducting parts of the machine due to voltage flashover. In case of voltage flashover, a voltage drop where major voltage differences are present is created on the ground around the machine. Due to major voltage differences in the ground, people may be killed by electric shocks when making big steps, laying on the ground or supporting themselves with their hands.

„ Do not leave the cabin.

„ Do not touch any metal parts.

„ Do not establish any conductive connection to the ground.

„ Warn people: Do not approach the machine. Electrical voltage differences on the ground may lead to severe electric shocks.

„ Wait for help from professional rescue teams. The overhead line must be switched off.

If people have to leave the cabin despite the voltage flashover, for example because there is an imminent danger to life due to fire:

„ Avoid simultaneous contact with machine and ground.

„ Jump away from the machine. Jump into a safe standing position. Do not touch the machine from the outside.

„ Move away from the machine in very small steps keeping your feet close together.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 21

2

2.4

2.4.18

Safety

Basic safety instructions

Sources of danger on the machine

Noise may damage your health

The noise development of the machine during operation may cause health damage such as hardness of hearing, deafness or tinnitus. When using the machine at high rotational speed, the noise level also increases. The height of the sound pressure level depends mainly on the tractor used. The emissions value was measured with the cabin closed under conditions according to

DIN EN ISO 4254-1, Appendix B, see Page 49

.

„ Before starting up the machine, estimate the risk caused by noise.

„ Depending on the ambient conditions, working hours and the working and operating conditions of the machine, specify and use suitable hearing protection.

„ Specify rules for the use of hearing protection and for the working time.

„ During operation keep windows and doors of the cabin closed.

„ Remove hearing protection for road travel.

Liquids under high pressure

The following liquids are under high pressure:

• Hydraulic oil

Liquids escaping under high pressure may penetrate through the skin and cause severe injuries.

„ Shut down and safeguard the machine and contact qualified specialist workshop upon suspicion of damaged hydraulic system.

„ Never search for leaks with bare hands. Even a very pin-sized hole may lead to serious injuries.

„ When searching for leaks, use suitable aids, e.g. a piece of cardboard to avoid injuries.

„ Keep body and face away from leaks.

„ If liquids penetrate the body, immediately consult a doctor. The liquid must be removed from the body as quickly as possible.

Hot liquids

Persons can suffer burns and/or scalding when hot liquids are drained.

„ Wear personal protective equipment when hot consumables are drained.

„ If necessary, allow liquids and machine parts to cool down before you start repair, maintenance and cleaning work.

Damaged hydraulic hoses

Damaged hydraulic hoses may tear off, burst or cause oil leaks. As a result, the machine may be damaged and people may be seriously injured.

„

Shut down and safeguard the machine, see Page 24

.

„ If it is suspected that hydraulic hoses are damaged, immediately contact a service centre,

see Page 119

.

22

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Basic safety instructions

Hot surfaces

The following components may become hot during operation and may burn people:

• Gearbox

• Cutterbar

„ Maintain an adequate distance from hot surfaces and adjacent components.

„ Leave machine parts to cool down and wear protective gloves.

2

2.4

2.4.19

Dangers in connection with certain activities: Working on the machine

Only perform work when the machine is at standstill

If the machine is not shut down and safeguarded, parts may move unintentionally or the machine may start moving. Thus there is a risk of serious injuries or death.

„ Before carrying out any repair, maintenance and cleaning work on the machine, shutdown and safeguard it,

see Page 24

.

Maintenance and repair work

Improper maintenance and repair work endanger operational safety. Thus there is a risk of accidents, serious injuries or death.

„ Only perform work which is described in this operating instructions. Prior to any work, stop

and safeguard the machine, see Page 24

.

„ All other maintenance and repair work must only be performed by qualified specialist workshop.

Working at or on heights of the machine

There is a risk of falling when working at or on heights of the machine. As a result, accidents may occur and people may be seriously or fatally injured.

„

Prior to any work, stop and safeguard the machine, see Page 24 .

„ Make sure you stand securely.

„ Use a suitable fall protection.

„ Secure the area below the assembly point against falling objects.

Raised machine and machine parts

The raised machine and machine parts may fall or tilt unintentionally. People may be seriously injured or killed, as a result.

„

Do not stay under the raised machine or machine parts which are not safely supported, see

Page 25 .

„ Prior to all work on raised machines or machine parts, lower the machine or machine parts.

„ Before performing any work under raised machines or machine parts, secure the machine or machine parts with rigid safety support or with hydraulic shut-off device or by supporting against lowering.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 23

2

2.5

Safety

Safety routines

Danger associated with welding work

Improper welding work will endanger the operational safety of the machine. As a result, accidents may occur and people may be seriously or fatally injured.

„ Never perform welding work on the following components:

• Gearbox

• Components of the hydraulics

• Components of the electronics

• Frame or supporting components

• Running gear

„ Before carrying out welding work on the machine, obtain consent by KRONE customer service and, if required, identify alternatives.

„ Before performing welding work on the machine, park the machine safely and disconnect it from the tractor.

„ Welding work must only be performed by experienced qualified personnel.

„ Attach the earthing of the welding device near the welding points.

„ Caution when performing welding work near electric and hydraulic parts, plastic parts and pressure accumulators. The parts may be damaged, endanger people or cause accidents.

2.4.20

Behaviour in dangerous situations and in case of accidents

Any measures not taken or incorrect measures in dangerous situations can make it difficult or impossible to rescue exposed persons. Due to the impeded conditions of rescue, the chances to help and heal injured people deteriorate.

„ As a matter of principle: Park the machine.

„ Get an overview of the existing danger and identify the reason.

„ Secure the accident site.

„ Save persons from the danger zone.

„ Leave danger zone and do not enter it again.

„ Alarm rescue workers and seek help, if possible.

„ Carry out immediate lifesaving actions.

2.5

Safety routines

2.5.1

Shutting down and safeguarding the machine

WARNING

Risk of injury due to movement of the machine or machine parts

If the machine has not been shut down, machine or machine parts may move unintentionally.

As a result, people may be seriously injured or killed.

„ Before leaving the operating position: Shut down and safeguard the machine.

24

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.5.2

2.5.3

Safety

Safety routines

To shut down and safeguard the machine:

„ Park the machine on a stable, horizontal and level ground.

„ Switch off the drives and wait until coasting parts have come to a complete stop.

„ Lower the machine all the way to the ground.

„ Switch off the tractor engine, remove the ignition key and take it with you.

„ Secure the tractor against rolling away.

2

2.5

Securing raised machine and machine parts against lowering

WARNING

Crushing hazard due to movement of machine or machine parts

If the machine or machine parts are not secured against lowering, the machine or machine parts may roll, fall or sag. Thus people could be squeezed or killed.

„ Lower the raised machine parts.

„ Shut down and safeguard the machine,

see Page 24

.

„ Before working on or under raised machine parts: Secure machine or machine parts against lowering by means of hydraulic shut-off device (e.g. stop cock) on machine side.

„ Before working on or under raised machine parts: Safely support machine or machine parts.

In order to safely support the machine or machine parts:

„ To support, only use suitable and sufficiently dimensioned materials that do not break or yield.

„ Bricks and hollow blocks are not suitable for safely supporting the machine and machine parts. Therefore they must not be used.

„ Car jacks are also not suitable for safely supporting the machine and machine parts. They must not be used, as well.

Carrying out oil level check and oil and filter element changes safely

WARNING

Safely checking the oil level and changing oil and filter element

The operational safety of the machine can be impaired if oil level check and oil and filter element changes are not carried out safely. This can lead to accidents.

„ Safely check the oil level and change oil and filter element.

To check the oil level and change oil and filter element safely:

„ Lower raised machine parts or secure them against falling down,

see Page 25 .

„

„Shut down and safeguard the machine, see Page 24 .

„ Observe the intervals for oil level check, oil and filter element changes,

see Page 105

.

„ Use only the oil grades/oil quantities specified in the consumables table,

see Page 50

.

„ Ensure that the oil and the equipment for filling are clean.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 25

2

2.6

Safety

Safety Labels on the Machine

„ Clean the area around the components (for example gearbox, high-pressure filter) and make sure that no foreign objects get into the components or the hydraulic system.

„ Check installed seal rings for damage. Replace them if necessary.

„ Collect leaking oil and/or waste oil in a container provided for this purpose, and dispose of it

properly, see Page 21 .

2.6

Safety Labels on the Machine

Every safety label is provided with an order number and can be ordered directly from the authorised KRONE dealer. Immediately replace missing, damaged and unrecognisable safety labels.

When attaching safety labels, the contact surface on the machine must be clean and free of dirt, oil and grease to ensure optimum adhesion of the labels.

26

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Safety Labels on the Machine

2

2.6

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 27

2

2.6

Safety

Safety Labels on the Machine

Position and meaning of safety labels

For the “pushed” version

KM000-333

28

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Safety Labels on the Machine

2

2.6

1.

Ord. no. 939 101 4 (1x)

2.

Ord. no. 939 471 1 (1x)

Danger when exceeding the maximum permissible PTO speed or the maximum permissible operating pressure

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

If the maximum permissible operating pressure is exceeded, hydraulic parts may be damaged.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

„ Observe the permitted operating pressure.

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

„ Before starting up the machine, read and follow the operating instructions and safety instructions.

3.

Ord. no. 939 576 0 (4x) a)

Danger due to rotating machine parts

When the machine has been switched off, there is risk of injury due to coasting machine parts.

„ Do not touch any moving parts of the machine.

„ Wait until the machine parts have come to a standstill.

b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ Before starting up, move the guards into their protective position.

c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ When the machine is running, keep your distance.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 29

2

2.6

Safety

Safety Labels on the Machine

4.

Ord. no. 942 197 1 (4x)

Danger from objects being ejected

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ When the machine is running, keep your distance.

5.

Ord. no. 939 106 3 (1x)

Danger to life when exceeding the maximum permitted

PTO speed

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

6.

Order no. 942 002 4 (1x)

7.

Ord. no. 27 021 591 0 (1x)

Danger due to rotating machine parts

When the machine is running, there is a risk of injury due to rotating machine parts.

„ Before starting up, move the guards into their protective position.

Danger if the regulating valves of the tractor are not locked

There is a risk of accidents if the regulating valves of the tractor are not locked.

„ To prevent functions from being triggered accidentally, the regulating valves of the tractor must be in neutral position and locked during road transport journeys.

30

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Safety Labels on the Machine

2

2.6

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 31

2

2.6

Safety

Safety Labels on the Machine

For the “trailed” version

KM000-338

32

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Safety Labels on the Machine

2

2.6

1.

Ord. no. 939 101 4 (1x)

2.

Ord. no. 939 471 1 (1x)

Danger when exceeding the maximum permissible PTO speed or the maximum permissible operating pressure

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

If the maximum permissible operating pressure is exceeded, hydraulic parts may be damaged.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

„ Observe the permitted operating pressure.

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

„ Before starting up the machine, read and follow the operating instructions and safety instructions.

3.

Ord. no. 939 576 0 (4x) a)

Danger due to rotating machine parts

When the machine has been switched off, there is risk of injury due to coasting machine parts.

„ Do not touch any moving parts of the machine.

„ Wait until the machine parts have come to a standstill.

b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ Before starting up, move the guards into their protective position.

c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ When the machine is running, keep your distance.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 33

2

2.6

Safety

Safety Labels on the Machine

4.

Ord. no. 942 197 1 (4x)

Danger from objects being ejected

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ When the machine is running, keep your distance.

5.

Ord. no. 939 106 3 (1x)

Danger to life when exceeding the maximum permitted

PTO speed

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

6.

Order no. 942 002 4 (1x)

Danger due to rotating machine parts

When the machine is running, there is a risk of injury due to rotating machine parts.

„ Before starting up, move the guards into their protective position.

7.

Ord. no. 942 196 1 (2x)

Danger due to crushing or shearing

Risk of injury due to crushing or shearing points on moving machine parts.

„ While parts are moving, never reach into areas where there is a risk of being crushed.

8.

Ord. no. 27 002 459 0 (1x)

Danger due to machine parts unintentionally folding down or swivelling out

Risk of injury for road users due to machine parts unintentionally folding down or swivelling out.

„ Whenever transporting the machine or driving on roads, ensure that the stop cock is closed.

34

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.7

Safety

Information labels on the machine

9.

Ord. no. 27 021 591 0 (1x)

Danger if the regulating valves of the tractor are not locked

There is a risk of accidents if the regulating valves of the tractor are not locked.

„ To prevent functions from being triggered accidentally, the regulating valves of the tractor must be in neutral position and locked during road transport journeys.

2

2.7

Information labels on the machine

Each information label has an order number. You can order the labels directly from your

KRONE dealer. Replace missing, damaged and illegible information labels immediately.

Prior to attaching an information label, ensure that the contact surface on the machine is clean and free of dirt, oil and grease so that the label can adhere to properly.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 35

2

2.7

Safety

Information labels on the machine

Location and meaning of the information labels

For the “pushed” version

7

2 3 4 5 6

1

9 9

KM001-045

8

36

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Information labels on the machine

1.

Ord. no. 27 009 074 0 (1x)

+

The label tells you that the degree of conditioning can be changed by adjusting the conditioning sheet at the lever.

2

2.7

+

27 009 074 0

2.

Ord. no. 27 017 118 0 (1x)

This label tells you that the raised machine must be aligned as parallel as possible to the ground

27 017 118 0

3.

Ord. no. 255 498 1 (1x)

Ø17mm

For the "Bolted blades" version

Check the material thickness of the retaining bolts after each blade change and after each contact with foreign objects. If the material thickness of the retaining bolts is below 14 mm at the weakest point, the retaining bolts must be replaced by authorised specialist personnel.

min. 14 mm

255 498 1

4.

Ord. no. 939 161 3 (1x)

DE

EN

ES

FR

IT

NL

RU

Mähwerk bei Rückwärtsfahrt ausheben.

Lift mower prior to reversing.

Levantar la guadanadora antes de retroceder.

Relever la faucheuse avant de reculer.

Sollevare la falciatrice prima di retrocedere.

Til de maaiwerk op tijdens het achteruitrijden.

Поднимать косилку при реверсе.

939 161 3

5.

Ord. no. 939 278 4 (1x)

DE

EN

ES

FR

IT

NL

RU

Vor der Erstinbetriebnahme und 1x jährlich vor der Ernte muss die Reibkupplung gelüftet werden

The friction clutch must be bled at the first operation and once a year before the harvesting season.

El embrague de seguridad debe someterse a una purga antes de la primera puesta en marcha y una vez al año antes de iniciarse la campaña de trabajo.

La sécurité à friction doit faire l'objet d'une purge lors de la première mise en route et une fois par an avant le début de la saison.

La frizione di sicurezza deve essere sottomessa ad uno spurgo alla prima messa in campo come pure una volta all'anno prima della campagna.

Voor de eerste inbedrijfstelling en eenmaal per jaar voor de oogst moet de frictiekoppeling worden belucht.

Перед первым вводом в эксплуатацию и 1 раз в год перед уборкой урожая необходимо растормозить фрикционную муфту.

939 278 4

6.

Ord. no. 255 499 2 (1x)

This label tells you that the mower must be raised during reverse movement.

This label states that the friction clutch must be bled before the initial start-up and once a year before the season.

Ø17mm min.14mm

For the "Quick-change blades" version

Check the material thickness of the retaining bolts after each blade change and after each contact with foreign objects. If the material thickness of the retaining bolts is below 14 mm at the weakest point, the retaining bolts must be replaced by authorised specialist personnel.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 37

2

2.7

Safety

Information labels on the machine

7.

Ord. no. 939 567 1 (1x)

This label indicates the order numbers for spare blades.

139-888

139-889

139 888 139 889

8.

Ord. no. 27 012 695 0 (1x)

The label tells you that the conditioner speed can be changed by repositioning the V-belt.

600 1/min 900 1/min

27 012 695 0

9.

Ord. no. 27 011 190 0 (3x)

This label tells you that the guards can be opened with a screwdriver.

27 011 190 0

• Order no. 942 012 2

The lifting points on the machine are marked with this label,

see Page 92 .

942 012 2

• Ord. no. 27 021 260 0

27 021 260 0

There are several lubrication points on the machine which must be lubricated at regular intervals,

see Page 135

. Lubrication points that are not directly visible are additionally marked with this information label.

38

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Information labels on the machine

2

2.7

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 39

2

2.7

Safety

Information labels on the machine

For the “trailed” version

2 3 4 5 6

7

1

10

9

KM001-046

9

8

40

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Safety

Information labels on the machine

1.

Ord. no. 27 009 074 0 (1x)

+

The label tells you that the degree of conditioning can be changed by adjusting the conditioning sheet at the lever.

2

2.7

+

27 009 074 0

2.

Ord. no. 27 017 118 0 (1x)

This label tells you that the raised machine must be aligned as parallel as possible to the ground

27 017 118 0

3.

Ord. no. 255 498 1 (1x)

Ø17mm

For the "Bolted blades" version

Check the material thickness of the retaining bolts after each blade change and after each contact with foreign objects. If the material thickness of the retaining bolts is below 14 mm at the weakest point, the retaining bolts must be replaced by authorised specialist personnel.

min. 14 mm

255 498 1

4.

Ord. no. 939 161 3 (1x)

DE

EN

ES

FR

IT

NL

RU

Mähwerk bei Rückwärtsfahrt ausheben.

Lift mower prior to reversing.

Levantar la guadanadora antes de retroceder.

Relever la faucheuse avant de reculer.

Sollevare la falciatrice prima di retrocedere.

Til de maaiwerk op tijdens het achteruitrijden.

Поднимать косилку при реверсе.

939 161 3

5.

Ord. no. 939 278 4 (1x)

DE

EN

ES

FR

IT

NL

RU

Vor der Erstinbetriebnahme und 1x jährlich vor der Ernte muss die Reibkupplung gelüftet werden

The friction clutch must be bled at the first operation and once a year before the harvesting season.

El embrague de seguridad debe someterse a una purga antes de la primera puesta en marcha y una vez al año antes de iniciarse la campaña de trabajo.

La sécurité à friction doit faire l'objet d'une purge lors de la première mise en route et une fois par an avant le début de la saison.

La frizione di sicurezza deve essere sottomessa ad uno spurgo alla prima messa in campo come pure una volta all'anno prima della campagna.

Voor de eerste inbedrijfstelling en eenmaal per jaar voor de oogst moet de frictiekoppeling worden belucht.

Перед первым вводом в эксплуатацию и 1 раз в год перед уборкой урожая необходимо растормозить фрикционную муфту.

939 278 4

6.

Ord. no. 255 499 2 (1x)

This label tells you that the mower must be raised during reverse movement.

This label states that the friction clutch must be bled before the initial start-up and once a year before the season.

Ø17mm min.14mm

For the "Quick-change blades" version

Check the material thickness of the retaining bolts after each blade change and after each contact with foreign objects. If the material thickness of the retaining bolts is below 14 mm at the weakest point, the retaining bolts must be replaced by authorised specialist personnel.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 41

2

2.7

Safety

Information labels on the machine

7.

Ord. no. 939 567 1 (1x)

This label indicates the order numbers for spare blades.

139-888

139-889

139 888 139 889

8.

Ord. no. 27 012 695 0 (1x)

The label tells you that the conditioner speed can be changed by repositioning the V-belt.

600 1/min 900 1/min

27 012 695 0

9.

Ord. no. 27 011 190 0 (3x)

This label tells you that the guards can be opened with a screwdriver.

27 011 190 0

10. Ord. no. 27 012 695 0 (1x)

The label tells you that the spring relief can be adjusted by actuating the threaded spindle.

27 012 694 0

• Order no. 942 012 2

The lifting points on the machine are marked with this label,

see Page 92 .

942 012 2

• Ord. no. 27 021 260 0

42

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

2.8

27 021 260 0

Safety features

Safety

Safety features

2

2.8

There are several lubrication points on the machine which must be lubricated at regular intervals,

see Page 135

. Lubrication points that are not directly visible are additionally marked with this information label.

1

3

2

3

4

KMG000-088

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 43

2

2.8

Safety

Safety features

Pos.

1

Designation

Stop cocks

2

3

Support jack

Overload protection

4 Road travel lighting

Explanation

• When transporting the machine and when working under the machine, always close the stop cocks.

• The support jack is used to keep the machine stable when it is not connected to the tractor,

see Page 82

.

• The overload protection protects the tractor and the machine from load peaks

„ To avoid damaging the machine, switch off the

PTO shaft if the overload protection responds for a longer period of time (>1 s).

• The road travel lighting is used for road safety.

• Before driving on roads, switch on the road travel lighting and ensure that it functions properly.

44

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

3

3.1

Machine Description

Machine overview

For the “trailed” version

Machine Description

Machine overview

3

3.1

KM000-335

7

8

5

6

3

4

1

2

9

10

Spare blade drawer

Universally-jointed drive shaft

Universal shaft bracket

Relief spring

Swath flap

Tine rotor

Support jack

Guard cloth

Main gearbox

Friction clutch

15

16

17

18

19

11

12

13

14

Intermediate universal shaft

Mower gearbox

Lever to adjust the conditioning sheet

Side guard

Cutterbar

Front safety device

Belt drive

Blade key

Document storage tube

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 45

3

3.1

Machine Description

Machine overview

For the “pushed” version

46

KM000-334

7

8

5

6

3

4

1

2

9

10

Spare blade drawer

Universally-jointed drive shaft

Universal shaft bracket

Relief spring

Swath flap

Tine rotor

Support jack

Guard cloth

Main gearbox

Friction clutch

15

16

17

18

11

12

13

14

19

20

Intermediate universal shaft

Mower gearbox

Lever to adjust the conditioning sheet

Side guard

Cutterbar

Front safety device

Belt drive

Blade key

Supporting chain

Document storage tube

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

3.2

3.3

Machine Description

Overload protections on the machine

Overload protections on the machine

NOTICE

Machine damage due to load peaks

The overload protections protect the tractor and the machine from load peaks. For this reason, overload protections must not be modified. The warranty for the machine becomes void if other than the factory-specified overload protections are used.

„ Only use the overload protections installed in the machine.

„ To avoid early wear of the overload protection, switch the PTO shaft off if the overload protection responds for a longer period of time.

„

„Shut down and safeguard the machine, see Page 24

.

3

3.2

Universal shaft

A friction disc clutch on the universal shaft protects against overload. The friction disc clutch is set at the factory. Never change the adjustment without consulting your KRONE service partner.

To vent the friction clutch, see Page 111 .

Labelling

INFO

The entire identification plate represents a legal document and should not be altered or rendered illegible!

KMG000-021

I For "Pushed" version II For "Trailed" version

The machine data are specified on the type plate (1). The type plate is mounted on the face side on right on the housing.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 47

3

3.4

Machine Description

Intermediate universal shaft

Information for enquiries and orders

3.4

1

2

KRONE Agriculture SE

Heinrich-Krone-Str. 10, D-48480 Spelle

Type

Serial Number Model Year

Construction Year

3

4

DVG000-004

Example image

1 Type

2 Machine number (Masch.Nr.)

3 Model year

4 Year of manufacture

For inquiries about the machine and for ordering spare parts, please specify type (1), machine number (2) and year of manufacture (4) of the particular machine. To ensure that the data is always available, KRONE recommends that you enter it in the boxes on the front cover of these operating instructions.

Intermediate universal shaft

To ensure the functionality and to increase the lifetime, the friction clutch must be vented once a year before the beginning of the season,

see Page 111

.

48

KMG000-014

I For "Pushed" version II For "Trailed" version

The intermediate universal shaft (1) for the mower drive is connected with the friction clutch (2) towards the input gearbox.

The intermediate universal shaft (3) for the tine conditioner is connected to the freewheel (4) towards the input gearbox.

The friction clutch and the freewheel protect the tractor and the machine from damage.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

4

4.1

4.2

4.3

4.4

4.5

4.6

Technical data

Dimensions

4

4.1

Technical data

Dimensions

Dimensions

Working width

Parking height

Transport width

Transport height

3,160 mm

-

3,000 mm

-

Weights

Weights

Dead weight approx. 1,225 kg¹ ⁾ | approx.

1,385 kg² ⁾

Area output

Area output

Acreage output 3.5–4.0 ha/h

Cutting height

Cutting height

Series version

High-cut skid version

Combi skid version approx. 1–7 cm approx. 6–12 cm approx. 4–10 cm

Technically permitted maximum speed (road travel)

The technically permitted maximum speed may be restricted by different equipment features

(e.g. coupling device, axle, brake, tyres, etc.) or by statutory regulations in the country of use.

Technically permitted maximum speed (road travel)

Technically permitted maximum speed (road travel) 40 km/h

Airborne noise emission

Airborne noise emission

Emissions value (sound pressure level)

Measurement device

Accuracy class

Measurement uncertainty (according to DIN EN ISO 11201)

76.2 dB

Bruel & Kjaer, Type 2236

2

4 dB

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 49

4

4.7

4.7

Technical data

Ambient temperature

Ambient temperature

Ambient temperature

Temperature range for machine operation

4.8

4.9

Requirements for tractor - power

Requirements for tractor - power

Power requirement

PTO speed

Tractor requirements – hydraulics

Tractor requirements – Hydraulics

Max. operating pressure of hydraulic system

Hydraulic oil quality

Double-acting hydraulic connection

Single-acting hydraulic connection

4.10

4.11

4.12

50

-5 to +45 °C

60 kW (82 HP)

1,000 min ⁻ ¹

200 bar

Oil ISO VG 46

1x

1x

Requirements for the tractor – electrics

Requirements for tractor – electrics

Requirements for the tractor - electrics: road travel lighting 12 V, 7-pin socket

Machine equipment

Machine equipment

Lower link hitch

Number of cutting discs

Number of mower drums

Cat. II and cat. III

5 units

2 units

Consumables

NOTICE

Complying with change intervals for biooils

To ensure high life expectancy of the machine, it is absolutely necessary to comply with change intervals for biooils due to the ageing of the oils.

NOTICE

Machine damage due to mixing of oil

If oils, which have different specifications, are mixed with each other, the machine may be damaged.

„ Never mix oils, which have different specifications, with each other.

„ Contact your KRONE service partner before using an oil with a different specification after changing the oil.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

4.12.1

4.12.2

Technical data 4

Consumables 4.12

Bio-degradable lubricants on request

Oils

Designation

Input gearbox

Main gearbox

Cutterbar

Filling quantity

1.7 l

0.9 l

7.0 l

Specification

SAE 90

SAE 90

SAE 90

Initial filling ex works

Wiolin ML 4 SAE 90

Wiolin ML 4 SAE 90

Wiolin ML 4 SAE 90

The filling quantities of the gearboxes are guide values. The correct values result from oil

change/oil level check, see Page 120 .

Lubricating greases

Designation

Manual lubrication points

Filling quantity

As required 1

Specification

Lubricating grease to DIN

51818 of NLGI class 2, Li soap with EP additives

1 Lubricate the lubrication point until grease comes out of the bearing position. After lubricating, remove the grease coming out of the bearing position.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 51

5

5.1

5

Control and Display Elements

Hydraulic control units of the tractor

Control and Display Elements

5.1

Hydraulic control units of the tractor

Different functions of the machine are executed with the hydraulic control units of the tractor.

The following table explains the functions of the control units.

For the “pushed” version

Designation

Front hydraulics

Double-acting control unit

(2+/2-)

(Lifting/lowering the side guards)

Function

Float position

Lowers the mower from transport position to working position.

Pressure

Raises the mower from working position to transport position.

(2+)

Raises the side guards

(2-)

Lowers the side guards

For the “trailed” version

Designation

Single-acting control unit (1+)

(Raising/lowering mower)

Single-acting control unit (1+)

(Increasing/reducing ground pressure)

Double-acting control unit

(2+/2-)

(Lifting/lowering the side guards)

Function

Float position

Lowers the mower from transport position to working position.

(1+)

Raises the mower from working position to transport position.

Float position

Increases the ground pressure

(1+)

Reduces the ground pressure

(2+)

Raises the side guards

(2-)

Lowers the side guards

52

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

6

6.1

Commissioning

Checklist for initial operation

Commissioning

This chapter describes assembly and adjustment work on the machine which may be carried out by qualified technicians only. Here, the notice “Personnel qualification of technicians” applies,

see Page 14

.

6

6.1

WARNING

Risk of injury or damage to the machine due to faulty initial operation

If the initial operation is carried out incorrectly or incompletely, the machine may present defects. As a result, people may be injured or killed or the machine may be damaged.

„ Initial operation must only be carried out by authorised technicians.

„ Read in full and observe the “Personnel qualification of technicians”,

see Page 14 .

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

Checklist for initial operation

ü The supplied operating instructions are in the document storage tube.

ü The machine is mounted according to assembly instructions of the machine.

ü All screws and nuts are checked for tightness, and are tightened to the specified tightening

torques, see Page 107 .

ü The safety devices are mounted and checked for completeness and damage.

ü The machine is fully lubricated,

see Page 135 .

ü

The oil level has been checked for all gearboxes, see Page 120 .

ü The hydraulic system has been checked for leaks.

ü The tractor corresponds to the machine requirements,

see Page 49 .

ü The axle loads, the minimum counterweight and the total weight have been checked.

see

Page 49 .

ü The length of the universal shaft has been checked and adjusted,

see Page 54 .

ü

The blades have been inserted, see Page 127 .

ü The hydraulic system has been vented.

ü The friction clutch has been vented,

see Page 111

.

ü The coupling points have been adapted,

see Page 56

.

ü The clearance between tractor and machine has been checked,

see Page 66

.

ü With "Road travel lighting" version : Functioning and cleanliness of the road travel

lighting were checked, see Page 72 .

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 53

6

6.2

6.2

Commissioning universal shaft

universal shaft

6.2.1

Adapting universal shaft

NOTICE

Changing the tractor

There is a risk of damaging the machine if the length of the universal shaft is not checked when the tractor is changed.

„ To prevent damage to the machine, check the length of the universal shaft whenever you change tractors. Have it corrected by a KRONE service partner if necessary.

KMG000-047

ü The machine is connected to the tractor,

see Page 65 .

„

Shut down and safeguard the machine, see Page 24

.

„ Disassemble the universal shaft.

„ Install one of the two halves (1, 2) on the tractor side and one on the machine side.

„ Shorten profile tubes and guard tubes as specified in the operating instructions of the universal shaft manufacturer.

NOTICE: Material damage caused by failure to achieve profile overlap! Observe an overlap (shift length) of the profile tubes and guard tubes of at least 200 mm, refer to the operating instructions of the universal shaft manufacturer.

„ Check the overlapping of profile tubes and guard tubes.

The ends of the enclosed universal shaft are equipped with a longer and a shorter guard over the joints. The joint with the longer guard must be pushed towards the machine onto the drive shaft.

54

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

6.2.2

Mounting the universal shaft on the machine

3 5 1

Commissioning

Mounting lighting system

6

6.3

2

4

6.3

KMG000-053

ü

The machine has been shut down and secured, see Page 24

.

„ Dismount the guard (5).

„ Push the universal shaft (3) with the full guard (2) onto the PTO shaft end of the input gearbox until the fuse engages.

„ Secure the full guard (2) against turning by using the pipe clamp (4).

„ Put the universal shaft (3) down on the universal shaft bracket (1).

„ Mount the guard (5).

INFO

More details can be found in the operating instructions for the universal shaft.

Mounting lighting system

For the version with "Road travel lighting"

WARNING

Dangers during road travel

There is a risk of endangering other road users when driving on public roads if the machine does not comply with the regulations for lighting and warning panels specified by national law.

„ Prior to driving on a public road ensure that the lighting is mounted.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 55

6

6.4

Commissioning

Adapting coupling points

I 2 2 II 2 2

2

1 1

2 2

1 1

2

6.4

KMG000-054

1 1 1 1

I For "Pushed" version II For "Trailed" version

Mount the lighting system (1) according to the instructions for accessories kit (document number

150 001 118).

Adapting coupling points

Adapting the lower link pins

For the “pushed” version

Kat.II

Kat.II

1

Kat.III

2

3

KMG000-095

2

Lower link pins

The three-point linkage is designed for category II and III.

5

4

2

Kat.III

1

2 3

56

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Commissioning

Adapting coupling points

Conversion to category II

„ Pull out the lower link pins (2).

„ Insert the lower link pins (2) through the ball sleeve cat. II (1).

„ Secure the lower link pins (2) by means of the linch pin (4) and the safety chain (5).

The shorter journal of the lower link pin (2) faces inwards.

6

6.4

Conversion to category III

„ Pull out the lower link pins (2).

„ Turn the lower link pins (2) by 180° and insert them through the ball sleeves cat. III (3).

„ Secure the lower link pins (2) by means of the linch pin (4) and the safety chain (5).

The longer journal of the lower link pin (2) faces inwards.

Top link pin

The top link pin (1) is designed for category II and III.

Kat.II

2

Kat.III

2

1 4 I

II

III

1 3

KMG000-096

Category II (Cat. II)

„ Loosen the linch pin (3) and pull out the top link pin (1).

„ Insert the top link bolt (1) in position (I), (II) or (III) and through the ball sleeve cat. II (2).

The thicker journal of the top link pin (1) faces outwards.

„ Secure the top link bolt (1) using the linch pin (3).

„ Make sure that the anti-twist lock (4) of the top link pin is in the recess.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 57

6

6.4

Commissioning

Adapting coupling points

Category III (Cat. III)

„ Loosen the linch pin (3) and pull out the top link pin (1).

„ Insert the top link bolt (1) in position (I), (II) or (III) and through the ball sleeve cat. III (2).

The thinner journal of the top link pin (1) faces outwards.

„ Secure the top link bolt using the linch pin (3).

„ Make sure that the anti-twist lock (4) of the top link pin is in the recess.

For the “trailed” version

Kat.II

Kat.II

58

1

Kat.III

2 2

Kat.III

1

5

4

3

KMG000-081

2 2 3

Lower link pins

The three-point linkage is designed for category II and III.

Conversion to category II

„ Pull out the lower link pins (2).

„ Insert the lower link pins (2) through the ball sleeve cat. II (1).

„ Secure the lower link pins (2) by means of the linch pin (4) and the safety chain (5).

The shorter journal of the lower link pin (2) faces inwards.

Conversion to category III

„ Pull out the lower link pins (2).

„ Turn the lower link pins (2) by 180° and insert them through the ball sleeves cat. III (3).

„ Secure the lower link pins (2) by means of the linch pin (4) and the safety chain (5).

The longer journal of the lower link pin (2) faces inwards.

Top link pin

The top link pin (1) is designed for category II and III.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Kat.II

2

Commissioning

Adapting coupling points

Kat.III

6

6.4

2

1 4

1 3

II

I

KM000-351

Category II (cat. II)

„ Loosen the linch pin (3) and pull out the top link pin (1).

„ Insert the top link pin (1) in the position (I) or (II) and through the ball sleeve cat. II (2).

The thicker journal of the top link pin (1) is facing outwards.

„ Secure the top link pin with the linch pin (3).

„ Make sure that the anti-twist lock (4) of the top link pin is in the recess.

Category III (cat. III)

„ Insert the top link pin (1) in the position (I) or (II) and through the ball sleeve cat. III (2).

The thinner journal of the top link pin (1) is facing outwards.

„ Secure the top link pin with the linch pin (3).

„ Make sure that the anti-twist lock (4) of the top link pin is in the recess.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 59

7

7.1

7

Start-up

Calculating the ballasting of the tractor-machine combination

Start-up

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of injury or damage to the machine due to connection lines which have been incorrectly connected, interchanged or improperly installed

If the connection lines of the machine have been incorrectly connected to the tractor or have been improperly installed, they may pull off or be damaged. This may result in serious accidents. If connection lines are interchanged, functions may inadvertently be actuated which may also result in serious accidents.

„ Correctly connect and secure the hoses and cables.

„ Lay the hoses, cables and ropes so that they do not scrape, come under tension or become jammed or come into contact with other components (e.g. tractor tyres).

„ Couple and connect the hoses and cables to the designated connections as described in the operating instructions.

7.1

Calculating the ballasting of the tractor-machine combination

WARNING

Danger due to wrong weight distribution in the tractor-machine combination

Due to wrong weight distribution in the tractor-machine combination, people may be seriously or fatally injured.

„ Before starting up the tractor-machine combination, check the following requirements and, if required, adjust according to the operating instructions.

When attaching implements at the front and rear, the permitted total weight, the permitted axle loads and the tyre load capacity of the tractor must not be exceeded. These specifications can be found on the type plate, in the vehicle registration document or in the operating instructions for the tractor.

Even with an implement mounted at the rear, the front axle of the tractor must always be loaded with at least 20% of the tare weight of the tractor.

„ To ensure the suitability of the tractor, perform the following calculation before mounting the implement on the tractor:

60

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Start-up

Calculating the ballasting of the tractor-machine combination

7

7.1

e

G

V a f

T

V

T

L b

T

H c d

G

H

Abbreviations for calculating the ballasting

TL [kg] Tare weight of the tractor See operating instructions for the tractor

TV [kg] Front axle load of the empty tractor See operating instructions for the tractor

TH [kg] Rear axle load of the empty tractor See operating instructions for the tractor

GH [kg] Total weight implement mounted at the rear/rear weight

GV [kg] Total weight of implement mounted at the front/front ballast

See price list and/or operating instructions for the machine

See price list and/or operating instructions for the machine a [m] Distance between centre of gravity of implement mounted at the front/ front ballast and middle of front axle b [m] Wheel base of the tractor

See price list and/or operating instructions for the machine

Measuring

See operating instructions for the tractor

Measuring c [m] Distance between middle of rear axle and middle of lower link ball

See operating instructions for the tractor

Measuring

See price list and/or operating instructions for the implement d [m] Distance between middle of lower link ball and centre of gravity of implement mounted at the rear/rear weight f e [m] Distance between middle of lower link ball and centre of gravity of implement mounted at the front

[m] Distance between front axle and middle of lower link ball

Calculation of the minimum ballasting at front G

V min for implements mounted at the rear and front and rear combinations

G

V min

=

G

H

• ( c +

( e d )

+

− f

T

V

) +

• b b + 0 , 2 • T

L

• b

„ Enter the calculated minimum ballasting, which is required at the front of the tractor, in the table.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 61

7

7.1

Start-up

Calculating the ballasting of the tractor-machine combination

Calculation of the minimum ballasting at rear G

H min for implements mounted at the front

G

H min

=

G

V

• ( e + f ) − T

H b + c +

• b d

+ x • T

L

• b

„ For "x" observe the technical data of the tractor manufacturer. If "x" is not indicated, insert the value 0.45.

„ Enter the calculated minimum ballasting, which is required at the rear of the tractor, in the table.

Calculation of the actual front axle load T

V tat

T

V tat

=

G

V

• ( e + f + b ) + b

T

V

• b − G

H

• ( c + d )

„ Enter the actual front axle load and the permitted front axle load, indicated in the operating instructions for the tractor, in the table.

Calculation of the actual total weight G tat

G tat

= G

V

+ T

L

+ G

H

„ If the required minimum ballasting at rear (G

H min

) is not reached with the implement mounted at the rear (G

H

), the weight of the implement mounted at the rear must be increased to the weight of the minimum ballasting at rear.

„ Enter the calculated, actual total weight and the permitted total weight, indicated in the operating instructions for the tractor, in the table.

Calculation of the actual rear axle load T

H tat

T

H tat

=

G tat

T

V tat

„ Enter the calculated, actual rear axle load and the permitted rear axle load, indicated in the operating instructions for the tractor, in the table.

Tyre load capacity

„ Enter double the value (two tyres) of the permitted tyre load capacity (see e.g. documents of the tyre manufacturers) in the table.

Table

The minimum ballasting must be attached to the tractor as a mounted implement or ballast weight. The calculated values must be less than/equal to (≤) the permitted values.

62

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

7.2

Minimum ballasting

Front/rear

Total weight

Front axle load

Actual value according to calculation kg kg

<

Permitted value according to operating instructions for the tractor

Start-up

Preparing tractor

Double permitted tyre load capacity

(two tyres)

7

7.2

kg

< kg kg

< kg

Rear axle load kg

< kg

< kg

Preparing tractor

NOTICE

Damage to the machine because the clearance is too small

If the clearance between the front wheels of the tractor and the machine is too low, the machine may be damaged during use.

„ Check the clearance between the front wheels of the tractor and the machine after placing the machine in service the first time and whenever changing the tractor wheels.

„ Check the clearance of the front wheels at all steering angles. If the guards or swath flaps come into contact with the front wheels of the tractor, mount the lower link extensions

between the lower links and the coupling triangle, see Page 66 .

+B -B

KM001-113

Prior to connecting the mower to the tractor, check whether the tractor can be connected with respect to the distances (A) and (+B/-B) as a function of the clearance. Connecting the universally-jointed drive shaft must be possible without any collision and with a small bending angle between mower and tractor. Follow the operating instructions of the universal shaft manufacturer.

For the “pushed” version

„ Check distance (A) and distance (+B/-B).

ð Distance (A)=900 mm

ð Distance (-B) (hidden lower link point)=200 mm

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 63

7

7.3

Start-up

Mounting top link fork

For the “trailed” version

„ Check distance (A) and distance (+B/-B).

ð Distance (A)=900 mm

ð Distance (-B) (hidden lower link point)=180 mm

„ Change the front lifting unit over to single-acting.

„ Disconnect the lower links from the swing position.

„ Move the front axle suspension of the tractor to the central position and deactivate it.

7.3

Mounting top link fork

For the “pushed” version

WARNING

Danger to life caused by an incorrectly mounted top link fork

If a top link fork (1) has been mounted incorrectly, the threaded spindle may break and the machine may disconnect unintentionally. This may result in serious accidents.

„ When mounting the top link fork, make sure that the rounded side (4) of the top link fork is facing upwards and the fork (3) below the straight side is attached to the top link fork.

2 4

3

1

3

KMG000-062

INFO

The top link fork (1) can be ordered with the order number 20 433 452 0.

„ Screw the top link fork (1) into the top link (2) M30 x 3.5.

Alternatively, it is also possible to use a telescopic top link instead of a top link.

„ Fit the forks (3) below the straight side onto the top link fork.

„ Mount the top link fork with the rounded side (4) facing upwards on the tractor side.

„ Perform a visual inspection to check that the forks (3) are pointing downwards and the rounded off side (4) of the top link fork is pointing upwards.

64

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

7.4

Start-up

Connecting machine to tractor

7

7.4

Connecting machine to tractor

WARNING

Risk of injury due to unexpected movement of the machine

During the connecting/decoupling process of the front mounted mower, the machine may start to move unexpectedly and may therefore result in injury.

„ Only one person may carry out the connecting/decoupling process.

„ Make sure there is nobody in the danger zone during the connecting/decoupling process.

„ Stop the connecting/decoupling process immediately if there is somebody in the danger zone.

NOTICE

When attaching implements at the front and rear, the permitted total weight, the permitted axle loads and the tyre load capacity of the tractor must not be exceeded. Even with an implement mounted at the rear, the front axle of the tractor must always be loaded with at least 20% of the tare weight of the tractor.

„ Prior to starting the trip, ensure that these conditions are met,

see Page 60 .

KMG000-049

WARNING! Increased risk of injury! Nobody is allowed to be between tractor and machine during the connecting process (especially when the tractor is moving forward).

„ Lower the front linkage hydraulically until the lower links (1) of the tractor are below the lower link pins of the machine.

„ Advance the tractor forward up to the machine.

„ Raise the front linkage hydraulically until the lower links (1) engage in the ball sleeves and lock.

„ Switch off the tractor, remove the ignition key and take it with you.

„ Secure the tractor against rolling away.

„ Engage the top link (2) at the three-point hitch, and secure it.

For "Relief springs" version

„

Mount relief springs, see Page 68

.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 65

7

7.5

Start-up

Mounting lower link extension

Check clearance

NOTICE

Damage to the machine because the clearance is too small

If the clearance between the front wheels of the tractor and the machine is too low, the machine may be damaged during use.

„ Check the clearance between the front wheels of the tractor and the machine after placing the machine in service the first time and whenever changing the tractor wheels.

„ Check the clearance of the front wheels at all steering angles. If the guards or swath flaps come into contact with the front wheels of the tractor, mount the lower link extensions

between the lower links and the coupling triangle, see Page 66 .

7.5

Mounting lower link extension

3

8 9 10 11

2

7

5

6

I

6 4

4

1

KMG000-114

The lower link extensions are used as an extension of the lower links to increase the distance between the machine and the front wheels of the tractor.

INFO

The accessories kit “Lower Link Extension” can be ordered by stating the order number

20 035 793 *.

ü The machine is disconnected from the tractor.

„ Dismount the installed lower link pin (1), the linch pin (2) and the safety chain (3), right and left side.

„ Detail (I): Drive the roll pin (6) into the larger diameter of the bolt (4) provided.

„ Insert the lower link extension (5) into the opening of the three-point hitch.

„ Push the preassembled bolt (4) from the inside through the three-point hitch and through the lower link extension.

Ensure that the roll pin (6) sits in the groove of the three-point hitch.

„ To secure the bolt (4), drive the roll pin (7) through the bolt.

„ Screw the lower link extension with disc (8), sleeve (9), disc (10) and screw (11) on the three-point hitch.

The thicker disc sits between the lower link extension and the sleeve.

„ Mount the safety chain (3) on the lower link extension (5).

„ Push the lower link pin (1) through the lower link extension and secure it with the linch pin (2), right and left side.

66

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

7.6

Start-up

Checking/setting parallel lifting

Checking/setting parallel lifting

NOTICE

If the machine does not lift in parallel with to the ground, the machine or the tractor may be damaged.

If the machine does not lift in parallel with the ground, the universal shaft may bend unfavourably. If the universal shaft is bent unfavourably, the machine will not run smoothly.

This may damage the machine or the tractor seriously.

„ To prevent damage, the machine must be aligned in parallel with the ground when it is lifted.

„ Whenever mounting the machine again, check the parallelism of the machine to the ground when it is lifted.

7

7.6

KM000-254

Secure the top link on the A-frame or on the upper coupling point of the machine such that the raised machine is aligned as parallel as possible to the ground.

ü The machine is mounted on the tractor.

„ Raise the machine via the front hydraulics,

see Page 85 .

„

Shut down and safeguard the machine, see Page 24

.

„ Ensure that the machine is parallel to the ground.

Æ Continue connecting when the machine is raised and parallel to the ground.

Æ If parallelism deviates too much:

„ Lower the machine to the ground,

see Page 85 .

„

Shut down and safeguard the machine, see Page 24

.

„ Relocate the top link in the hole pattern on the A-frame.

„ Raise the machine via the front hydraulics,

see Page 85 .

„ Ensure that the machine is parallel to the ground.

„ Repeat this process until the machine is raised parallel to the ground.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 67

7

7.7

7.7

Start-up

Mounting relief springs

Mounting relief springs

For the “pushed” version

KM000-356

With turnbuckle Without turnbuckle

The relief springs (1) can be attached to the top link fork (3) with or without turnbuckles (2).

If turnbuckles (I) are used, the turnbuckles (2) are attached between the supporting chains (4) of the relief springs and the top link fork (3).

If no turnbuckles (II) are used, the supporting chains (4) of the relief springs are attached directly to the top link fork (3).

The ground pressure of the mower can be adjusted via the perforated bar, via the length of the supporting chain and, if using the turnbuckle, via the turnbuckle.

KMG100-004

„ Hook the relief springs (1) on the machine side into the third borehole (III) in the perforated bar (2).

68

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Attaching the relief springs with a turnbuckle

Start-up

Mounting relief springs

7

7.7

KM000-357

„ Lift the machine into the transport position via the front hydraulics,

see Page 86

.

„

Shut down and safeguard the machine, see Page 24

.

„ Mount the turnbuckle (1) with the connecting link (2) on the top link fork (3).

„ Set the turnbuckle (1) to a maximum dimension X=230 mm .

„ Attach the chain (4) to the turnbuckle (1) using the connecting link (5). In doing so, hook in the chains as short as possible and the same on both sides.

„ Remove excess chain links or attach in a suitable position.

„ Lower the machine into the working position via the front hydraulics.

NOTICE

The relief springs are optimally adjusted when the inclination of the supporting chains is approximately 35° in the working position.

Attaching the relief springs without a turnbuckle

„ Lift the machine into the transport position via the front hydraulics,

see Page 86

.

„

Shut down and safeguard the machine, see Page 24

.

„ Attach the chain (4) to the top link fork (2) using the connecting link (5). In doing so, hook in the chains as short as possible and the same on both sides.

„ Lower the machine into the working position via the front hydraulics.

NOTICE

The relief springs are optimally adjusted when the inclination of the supporting chains is approximately 35° in the working position.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 69

7

7.7

Start-up

Mounting relief springs

Checking internal chains for overstretching

70

KM000-359

With turnbuckle (I) Without turnbuckle (II)

The relief springs (1) are prevented from overstretching by internal chains (2). To protect the relief springs from overstretching, the internal chains (2) must not tension in the working position.

Checking internal chains

„ Lower the machine into the working position via the front hydraulics.

„

Shut down and safeguard the machine, see Page 24

.

„ Visually check that the chains (2) do not tension.

ð If the chains (2) are sagging, everything is correct (III).

ð If the chains (2) are tensioned (IV), the chains (3) of the relief springs must be hooked into the next-longer chain link.

Hooking the supporting chain into the next-longer link

„ Lift the machine into the transport position via the front hydraulics.

„

Shut down and safeguard the machine, see Page 24

.

„ For mounting with turnbuckle: Hook the chain (3) into the turnbuckle by the next-longer chain link.

„ For mounting without turnbuckle: Hook the chain (3) into the top link fork (4) by the nextlonger chain link.

„ Repeat the process until the internal chains (2) no longer tension when the machine is in the working position.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

7.8

Start-up

Connecting hydraulic hoses

7

7.8

Connecting hydraulic hoses

WARNING

Risk of injury from escaping hydraulic oil

The hydraulic system operates at very high pressure. Escaping hydraulic oil may seriously injure skin, limbs and eyes.

„ Prior to connecting the hydraulic hoses to the tractor, depressurise both sides of the hydraulic system.

„ Depressurise the hydraulic system before you uncouple the hoses and work on the hydraulic system.

„ When connecting the quick couplings, ensure that they are clean and dry.

„

Check hydraulic hoses at regular intervals see Page 119 and replace them if they are

damaged (e.g chafing areas or points of contact) or aged. The replacement lines must comply with the technical requirements of the device manufacturer.

NOTICE

Damage to the machine due to soiling of the hydraulic system

If foreign objects or liquids get into the hydraulic system, the hydraulic system may be severely damaged.

„ When connecting the quick couplings, ensure that they are clean and dry.

„ Check the hydraulic hoses for abrasion and pinch point and replace if required.

KMG000-076

In order to connect the hydraulic hoses properly, the hydraulic hoses (1, 2) are marked with numbers or letters.

Hydraulic hoses for connection to a single-acting control unit are marked with a number and the plus sign, e.g. (1+).

Hydraulic hoses for connection to a double-acting control unit are marked with the same numbers, plus sign for the pressure line and minus sign for the return, for example (2+/2-).

Use a control unit on the tractor which can be locked in the neutral position against unintentional operation.

„ Depressurise the tractor hydraulics.

„

Shut down and safeguard the machine, see Page 24

.

„ Clean and dry the connections of the hydraulic quick connector.

For the "Hydraulic side guards" version

„ Connect the hydraulic hoses (2+/2-) to a double-acting control unit of the tractor.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 71

7

7.9

Start-up

Connecting road travel lighting

For the “trailed” version

„ Connect the hydraulic hose (1+) to a single-acting control unit of the tractor.

Alternatively, the hydraulic hose can be connected to a double-acting control unit.

7.9

Connecting road travel lighting

For the version with “road travel lighting”

NOTICE

Short circuit caused by impurities and moisture in the plug connection

The machine may be damaged by a short circuit.

„ Make sure that the plugs and sockets are clean and dry.

For the “trailed” version

3 2 1

KMG000-013

For the “pushed” version

72

KMG000-127

The road travel lighting is connected by means of the enclosed 7-pin lighting cable (2).

ü

The machine has been shut down and secured, see Page 24

.

„ Connect the 7-pin plug of the lighting cable (2) to the 7-pin socket (1) of the machine.

„ Connect the 7-pin plug of the lighting cable (2) to the 7-pin socket (3) of the tractor.

„ Route the lighting cable (2) so that it does not come into contact with the tractor wheels or other moving parts of the machine.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

7.10

Connect the Camera Monitor System

Start-up 7

Connect the Camera Monitor System 7.10

For "Camera-monitor system" version

1

2 3

11

10

9 8 7 6

5 4

BEI000-095

ü The monitor must be fixed within the driver’s cabin in such a way as to ensure the driver has the monitor within the field of vision.

„ Be careful to ensure that none of the display instruments are covered and that the field of vision of the driver is not obscured from the front.

„

Shut down and safeguard the machine, see Page 24

.

Monitor connection to the tractor

„ Connect the plug (10) of the cable (6) to the socket (CAM1) of the monitor (1).

„ Connect the plug (11) of the cable (6) to the socket (CAM2) of the monitor (1).

„ Connect the plug (2) of the cable (3) to the socket (POWER) of the monitor (1).

„ Connect the plug (4) of the cable (3) to the socket of 12 Volt of the monitor of the tractor (5).

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 73

7 Start-up

7.11

Tightening guard cloth

Connection from Tractor to the machine

The Camera Monitor System is connected with the 13-pin connecting cable (8) included in the delivery.

„ Connect the 13-pin plug of the connecting cable (8) with the 13-pin socket (9) of the machine.

„ Connect the 13-pin plug of the connecting cable (8) with the 13-pin socket (7) of the tractor.

„ Lay the cable such that it is not allowed to rub, be tightened, pinched or otherwise come into contact with other components, particularly when laid in corners.

7.11

Tightening guard cloth

7.12

2 1 2

KMG000-063

ü

The machine is shut down and safeguarded, see Page 24

.

„ Tighten the guard cloth (1) via the expanders (2) so that it does not come into contact with the tine conditioners.

Installing universal shaft

WARNING

Risk of injury by failure to take account of the danger zone of the universal shaft

If the danger zone of the universal shaft is ignored, persons can be seriously hurt or killed.

„ To avoid accidents, observe the danger zone of the universal shaft,

see Page 16

.

NOTICE

Changing the tractor

There is a risk of damaging the machine if the length of the universal shaft is not checked when the tractor is changed.

„ To prevent damage to the machine, check the length of the universal shaft whenever you change tractors. Have it corrected by a KRONE service partner if necessary.

74

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Start-up 7

Checking front end dimension 7.13

7.13

KMG000-048

“pushed” version “trailed” version

ü

The machine has been shut down and secured, see Page 24

.

ü The length of the PTO shaft is adapted as required by the currently used tractor.

„ Slip the universal shaft (1) onto the PTO shaft end of the tractor and secure it.

„ Secure the universal shaft guard with the supporting chain (2) against turning along with the shaft.

Checking front end dimension

KM000-265

INFO

Depending on the country

If the front end dimension “A” 3.5 m is exceeded, the road safety must be ensured by means of suitable aids (for example instructing accompanying person or mirror at the intersections), refer to the leaflet for accessory equipment issued by Federal Minister of Transport.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 75

7 Start-up

7.14

Checking locking device and latch

7.14

Checking locking device and latch

7.15

KM000-267

ü

The machine is in the working position, see Page 85 .

ü

The machine is shut down and safeguarded, see Page 24

.

On right-hand and left-hand machine side:

„ Check that locking device/latch (1) is tight.

„ Tighten the locking device/latch (1).

„ Check the locking device/latch (1) for damage and ageing.

„ Replace damaged and porous locking devices/latches (1).

INFO

Locking devices/latches (1) can be ordered by stating the order number 00 250 831 *.

Checking the tines on the tine conditioner

NOTICE

Loss of tines

Bent and broken tines will cause an imbalance. Therefore the machine may be damaged.

„ Check the tine conditioner for bent and damaged tines each time before it is used.

„ Replace bent or damaged tines before starting work.

„ To prevent a loss of tines, check the bearing journals of the tine bearings and replace them in time.

76

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Start-up 7

Basic setting of mower 7.16

7.16

KMG000-017

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Straighten bent and damaged tines (1); replace and mount them if necessary.

Basic setting of mower

For "Trailed" version, hydraulic relief adjustment

1

2

KM001-282

„ Lower the mower to the ground.

„ Set the single-acting control unit (1+) to float position.

„ Using the lower links, position the arrow (1) in the centre of the hydraulic cylinder (2).

„ Raise and lower the mower via the single-acting control unit (1+). Check the position of the arrow mark. Correct again if required.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 77

7 Start-up

7.16

Basic setting of mower

For "Trailed" version, mechanical relief adjustment

KM000-560

„ Lower the mower to the ground.

„ Set the single-acting control unit (1+) to float position.

„ Using the lower links, position the arrow (1) in the centre of the link (2).

„ Raise and lower the mower via the single-acting control unit (1+). Check the position of the arrow mark. Correct again if required.

78

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

8

8.1

8.1.1

Operation

Front guard

8

8.1

Operation

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of injury during operation

If the following notes are not observed, persons could be seriously injured or killed.

„ Before you turn on the PTO shaft, make sure that the machine is in working position and that the glide skids touch the ground.

„ Even with intended operation of the machine, there is a danger caused by ejected foreign bodies. Thus instruct all persons to leave the danger zone of the machine.

„ Special care should be taken when working near roads and buildings.

Front guard

WARNING

Risk of injury due to objects being flung out

If the front guard/side guard is folded up during work, objects may be flung out. As a result, people may be seriously injured.

„ Fold down the front guard/side guard.

„ Connect the guard cloths of the front guard and the side guard using the turnlock fasteners.

Folding up the front guard

The front guard can be folded up for repair and maintenance.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 79

8

8.2

Operation

Side guard - for the “series” version

2 2

1

8.1.2

3

KMG000-006

3

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Open the turnlock fasteners (3).

„ To fold up the front guard (1), press the catch with a screwdriver (2) and fold up the front guard.

Fold down the front guard

8.2

KMG000-077

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Fold down the front guard (1).

„ Close the turnlock fasteners (3).

Side guard - for the “series” version

WARNING

Risk of injury due to objects being flung out

If the front guard/side guard is folded up during work, objects may be flung out. As a result, people may be seriously injured.

„ Fold down the front guard/side guard.

„ Connect the guard cloths of the front guard and the side guard using the turnlock fasteners.

80

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

8.2.1

Operation

Side guard - for version with “hydraulically folding side guards”

Folding up the side guard - for "Series" version (transport position)

8

8.3

8.2.2

KMG000-058

ü

The machine is shut down and safeguarded, see Page 24

.

„ Open the turnlock fasteners (3).

„ To unlock the side guard (1), press down the ratchet using a screwdriver.

„ Fold up the side guard (1) until the side guard engages in the latch.

Folding down the side guard - for "Series" version (working position)

8.3

KMG000-059

ü

The machine is shut down and safeguarded, see Page 24

.

„ To fold down the side guard (1), pull the side guard out of the latch with the locking (2) pulled and fold it down.

„ Secure the guard cloths by means of the turnlock fasteners (3).

Side guard - for version with “hydraulically folding side guards”

WARNING

Risk of injury due to objects being flung out

If the front guard/side guard is folded up during work, objects may be flung out. As a result, people may be seriously injured.

„ Fold down the front guard/side guard.

„ Connect the guard cloths of the front guard and the side guard using the turnlock fasteners.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 81

8

8.4

8.3.1

Operation

Operating support jack

Folding up the side guard – in version "hydraulically folding side guards" (transport position)

8.3.2

KMG000-080

ü

The machine is in the working position, see Page 85 .

„

Shut down and safeguard the machine, see Page 24

.

„ Open the turnlock fasteners (2).

„ Actuate the double-acting control unit (2-) until the side guards (1) are folded up.

„ Lock the control unit of the tractor.

Folding down the side guard – in version "hydraulically folding side guards" (working position)

8.4

82

KMG000-079

ü

The machine is in the working position, see Page 85 .

„ Unlock the control unit of the tractor.

WARNING! Crushing hazard when folding down the side guards! Before folding down the side guards ensure that there is no one in the danger zone.

„ Actuate the double-acting control unit (2+) until the side guards (1) are folded down.

„

Shut down and safeguard the machine, see Page 24

.

„ Secure the guard cloths using the turnlock fasteners (2).

Operating support jack

INFO

In order to increase the base of the support jack when the ground is soft, use a suitable support.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

8.4.1

Moving support jack into transport position

2

Operation

Operating support jack

8

8.4

8.4.2

1

2

KMG000-065

„ Raise the machine via front hydraulics until the support jack (2) can be inserted.

„

Shut down and safeguard the machine, see Page 24

.

WARNING! Crush hazard due to the support jack! Keep hands and feet out of the danger zone of the support jack.

„ Pull the tension bar (1), insert the support jack (2) and lock it with the tension bar (1).

Moving support jack into support position

2

1 2

KMG000-064

„ Raise the machine via front hydraulics until the support jack (2) can be lowered.

„

Shut down and safeguard the machine, see Page 24

.

WARNING! Crush hazard due to the support jack! Keep hands and feet out of the danger zone of the support jack.

„ Pull the tension bar (1), lower the support jack (2) and lock it with the tension bar (1).

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 83

8

8.5

8.5

Operation

Locking/releasing stop cock

Locking/releasing stop cock

8.6

KMG000-089

Locking

„ Move stop cock (1) into position (I).

Releasing

„ Move the stop cock (1) into position (II).

Operating the stop cock

For the “trailed” version

84

1

KMG000-113

Moving machine into working / transport position

„ Move the stop cock (1) into position (I).

Locking

„ Move the stop cock (1) into position (II).

Setting the ground pressure

„ Move the stop cock (1) into position (III).

III II I

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

8.7

Operation

Lowering machine from transport position to working position

Lowering machine from transport position to working position

8

8.7

8.8

I

KMG000-117

1

WARNING

Danger to life, injuries or damage to the machine due to uncontrolled lowering of the machine

When lowering the machine into the working position, people or animals in the swivel range may be seriously injured and the machine may be damaged.

„ Lower the machine only when you are absolutely sure that there are no persons, animals or objects in the swivel range of the machine.

„ Only switch on the PTO shaft when the machine is in the working position.

For the “pushed” version

„ Move the control unit for the front hydraulics into the float position until the mower has been lowered into the working position.

„ Move the control unit for the front hydraulics into the float position for mowing.

For the “trailed” version

ü The stop cock (1) on the hydraulic hose (1+) is open.

„ Move the stop cock (1) into position (I),

see Page 84 .

„ Move the single-acting control unit (1+) to the float position until the mower is lowered to the working position.

„ To mow, move the control unit (1+) to the float position.

Raising machine from working position to transport position

1

II

KMG000-118

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 85

8

8.9

Operation

Field mode

For the “pushed” version

„ Actuate the control unit for the front hydraulics until the mower is raised to transport position.

„ Lock the control unit for the front hydraulics.

For the “trailed” version

„ Move the stop cock (1) into position (I),

see Page 84 .

„ Actuate the control unit (1+) until the mower is lifted into the transport position.

„ Move the stop cock (1) into position (II),

see Page 84 .

8.9

Field mode

Game animal protection

86

EQ003-725

When mowing from “outside to inside”, the animals are slowly forced from the safe boundary area into the centre of the area, which makes the possibility for a life-saving escape for the animal more difficult or takes it away.

A remedy for this issue is the mowing method from “inside to outside” of the area.

Instead of mowing any edge sections at first, the operator drives straight into the middle of the field and then mows in a left-handed spiral "from the inside to the outside". This allows animals to escape from the field unharmed by following their natural instinct to flee.

Preparation for mowing

ü All items listed in chapter "Start-up" are fulfilled,

see Page 60

.

ü The stop cock for tractor front hydraulics is open.

ü For the “trailed” version : The stop cock on the hydraulic hose (1+) is open.

ü

The machine is in the working position, see Page 85 .

ü The safety devices are folded down,

see Page 80

.

ü The support jack is inserted,

see Page 83 .

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

8.10

Operation 8

Operating the Camera Monitor System 8.10

Mowing

„ Prior to driving into the crops, switch on the tractor PTO shaft at idle speed and slowly accelerate to rated speed.

„ Drive into the crops.

„ Check the ground pressure during mowing,

see Page 96

.

„ To ensure a clean cutting pattern, adjust the driving and cutting speeds to the prevailing conditions (soil condition, state of the crops, height, density).

For the “pushed” version

INFO

Leave the control unit for front hydraulics in the float position during mowing.

For the “trailed” version

INFO

During mowing:

„ Leave the control unit (1+) in the float position.

„ Leave the control unit for front hydraulics in neutral position.

NOTICE

Damage to the machine caused by reversing

The machine is designed to drive forwards. Never reverse while the machine is switched on and in working position.

„ Lift the machine before reversing.

Operating the Camera Monitor System

For "Camera-monitor system" version

• To operate the Camera Monitor System please refer to the instructions of the monitor manufacturer.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 87

9 Driving and Transport

9 Driving and Transport

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of accident caused by non-locked regulating valves of tractor

When regulating valves are not locked, machine components could be activated unintentionally. This may result in serious accidents.

„ To avoid that functions are triggered by mistake, the regulating valves of the tractor must be in neutral position when performing transport journeys on the road and must be locked.

WARNING

Risk of accident from open stop cocks

Machine components could be moved unintentionally when stop cocks are open. This may result in serious accidents.

„ In order to avoid that functions are triggered by mistake, the stop cock/s must be closed during transport/road travel.

NOTICE

When attaching implements at the front and rear, the permitted total weight, the permitted axle loads and the tyre load capacity of the tractor must not be exceeded. Even with an implement mounted at the rear, the front axle of the tractor must always be loaded with at least 20% of the tare weight of the tractor.

„ Prior to starting the trip, ensure that these conditions are met,

see Page 60 .

88

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

9.1

Driving and Transport

Preparing the machine for road travel

Preparing the machine for road travel

9

9.1

KMG000-057

ü

All items listed in chapter "Start-up" have been fulfilled, see Page 60 .

ü

The machine has been shut down and secured, see Page 24

.

ü The hydraulic hoses are connected,

see Page 71 .

ü

The universal shaft is mounted, see Page 74 .

ü

The front guard is closed and locked, see Page 79

.

ü

The side guards are folded up, see Page 81 .

ü

The support jack is in the transport position, see Page 82

.

ü For the "Camera Monitor System" version: The camera monitor system is connected, switched on, functioning and the cameras have been cleaned.

The assistance system in the "Camera Monitor System" does not exempt the driver from responsibility for ensuring the safe operation of the machine on the road (StVO - Road

Traffic Act).

ü

The machine is in the transport position, see Page 85

.

ü The front hydraulics of the tractor are locked, via a stop cock (2), for example.

ü

The stop cocks on the hydraulic hose lines are closed, see Page 84

.

ü The control units on the tractor are in neutral position and locked.

ü The guard cloths of the side guards (1) of the side guards are laid towards the inside.

ü Depending on the national regulations:

The lighting is connected and functional, see

Page 72 .

ü Depending on the national regulations:

The lost load centre has been checked, see

Page 75 .

ü Soiling and crop residue have been removed from the machine, in particular from the lighting and identification elements.

ü Ground clearance is sufficient.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 89

9

9.2

9.2

Driving and Transport

Parking the machine

Parking the machine

For the “pushed” version

6

1

3

7 2

7

2

5

4

KMG000-019

WARNING

Risk of injury when removing the supporting chains

In the working position the retaining chains are subject to high drawing tension. In case an attempt is made to remove or adjust the supporting chain when the machine is in the working position, people may be seriously injured or killed.

„ The supporting chains must only be removed or set when the machine is in the transport position.

„ Lift the machine into transport position,

see Page 86 .

„

Shut down and safeguard the machine, see Page 24

.

„ Remove the supporting chains (2) of the spring relief from the tractor side.

„ Lower the support jack (1) and secure it with the bolt,

see Page 83

.

„ Lower the machine,

see Page 85

.

„ For the “hydraulically folding side guards” version: Depressurise the tractor hydraulics.

„

Shut down and safeguard the machine, see Page 24

.

„ Loosen the guard cloth (4).

„ Remove the supporting chain (5) of the universal shaft on the tractor side.

„ Remove the universal shaft (6) from the tractor side and place it on the universal shaft bracket (7).

„ For version with "Lighting": Pull the 7-pin plug of the connection cable out of the 7-pin socket of the tractor and place it on the machine.

„ Uncouple the hydraulic hose/the hydraulic hoses (2) from the tractor, attach the dust cap/s and place them on the machine.

„ Detach the top link (3).

„ Unlock the lower link hooks of the tractor.

„ Continue to lower the front lifting device until the lower link pins are free.

„ Carefully drive away by reversing the tractor.

90

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

For the “trailed” version

Driving and Transport

Preparing the machine for shipment

9

9.3

9.3

KMG000-083

„ Lift the machine into transport position,

see Page 86 .

„

Shut down and safeguard the machine, see Page 24

.

„ Lower the support jack (1) and secure it with the bolt,

see Page 83

.

„ Lower the machine,

see Page 85

.

„ For the “hydraulically folding side guards” version: Depressurise the tractor hydraulics.

„

Shut down and safeguard the machine, see Page 24

.

„ Loosen the guard cloth (4).

„ Remove the supporting chain (5) of the universal shaft on the tractor side.

„ Remove the universal shaft (6) from the tractor side and place it on the universal shaft bracket (7).

„ For version with "Lighting": Pull the 7-pin plug of the connection cable out of the 7-pin socket of the tractor and place it on the machine.

„ Uncouple the hydraulic hose/the hydraulic hoses (2) from the tractor, attach the dust cap/s and place them on the machine.

„ Detach the top link (3).

„ Unlock the lower link hooks of the tractor.

„ Continue to lower the front lifting device until the lower link pins are free.

„ Carefully drive away by reversing the tractor.

Preparing the machine for shipment

WARNING

Risk of accident due to unsecured machine parts

If the machine is not secured properly for transportation on a lorry or train, the parts may come loose unintentionally due to the airstream. This may result in serious accidents or damage to the machine.

„ Carry out the following measures to secure moving machine parts.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 91

9

9.3

9.3.1

Driving and Transport

Preparing the machine for shipment

Checklist for the transport of the machine

ü All guards are properly closed and locked.

ü The universal shaft is secured.

ü The hydraulic hoses are secured on the machine against dropping.

ü Using a hoist with a minimum lifting capacity, the machine was lifted at the marked

suspension points, see Page 92 . The minimum load capacity depends on the permissible

total weight of the machine,

see Page 49 .

ü The machine is secured with suitable lashing material at the designated lashing points.

9.3.2

Lifting the machine

WARNING

Risk of injury due to raised machine

There is danger to persons when the machine drops or parts swing without control. Only qualified personnel are allowed to perform this work.

„ Use only permitted hoists and slings with a sufficient load-bearing capacity. For the weights

see Page 49 .

„ Note the information on the suspension points provided.

„ Make sure the lifting means are properly secured.

„ Never stay under the suspended machine.

„

If work has to be performed under the machine, securely support the machine, see

Page 25 .

ü The machine is in the working position.

ü The machine is dismounted from the tractor.

For the “pushed” version

1

942 012 1

942 012 1

2

1

942 012 1

92

KMG000-122

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Driving and Transport

Preparing the machine for shipment

The machine is equipped with three suspension points:

• The suspension points (1) are on the support frame.

• The suspension point (2) is on the headstock.

9

9.3

For the “trailed” version

1 2

942 012 1

2 1

942 012 1

942 012 1

942 012 1

9.3.3

KMG000-123

The machine is equipped with four suspension points:

• The suspension points (1) are on the support frame.

• The suspension points (2) are on the headstock.

„ Ensure that the hoist is mounted correctly on the anchor points.

To lift the machine, ensure that a hoist is used whose minimum lifting capacity depends on the permissible total weight of the machine; see chapter "Technical data",

see Page 49

.

Lashing the machine

WARNING

Danger to life caused by uncontrolled machine movement

If the machine is not properly lashed for transportation by vehicle, the machine may move in an uncontrolled manner and endanger people.

„ Before transporting the machine, secure it properly using suitable lashing material.

Before transporting the machine, secure it in appropriate places using suitable lashing material.

„ Ensure that the machine is lashed in such a way that it cannot move in an uncontrolled manner when transported by vehicle.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 93

10 Settings

10.1

Setting the cutting height

10 Settings

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

10.1

Setting the cutting height

KMG000-035

The cutting height is adjusted via the top link (1).

Setting range of cutting height,

see Page 49 .

„

Shut down and safeguard the machine, see Page 24

.

„ Turn the top link until the cutting height is set.

ð Top link longer = smaller cutting height

ð Top link shorter = greater cutting height

For version with "high-cut skids"

The cutting height can be increased using high-cut skids.

94

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Settings 10

Telescopic top link 10.2

10.2

KMG000-025

ü The machine is in transport position.

ü The stop cocks are closed.

ü

The machine has been shut down and secured, see Page 24

.

ü

The machine is supported safely, see Page 25

.

„ The high-cut skids must always be mounted underneath the cutting discs that run next to the mower drums.

„ Insert the high-cut skid (2) into the sliding skid (1) and screw it in place.

„ Open the stop cocks.

Telescopic top link

KMG000-060

In order to allow the front mounted mower to adapt to the ground in the direction of travel, a telescopic top link can be purchased as optional additional equipment.

ü

The machine has been lifted into the transport position via the front hydraulics, see

Page 85 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ To release the ground tracking in the direction of travel, shift the lockclip (1).

Setting cutting height

Setting range of cutting height,

see Page 49 .

ü The machine has been lowered into the working position via the front hydraulics,

see

Page 85 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ To set the cutting height, loosen the counter nuts (2,3).

„ Turn the top link until the cutting height is set.

ð Top link longer = smaller cutting height

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 95

10 Settings

10.3

Adjusting the relief spring(s)

ð Top link shorter = greater cutting height

„ Tighten the counter nuts (2,3).

10.3

Adjusting the relief spring(s)

For the “pushed” version

WARNING

Risk of injury due to adjustment of relief spring(s)

In the working position the relief spring(s) are subject to high drawing tension. In case an attempt is made to remove or adjust the relief spring(s) when the machine is in the working position, people may be seriously injured or killed.

„ The relief spring(s) must only be dismounted or adjusted in the transport position.

„ The bottom fittings on the relief spring(s) are fully screwed in.

1

+

2

KMG000-039

The relief springs (1) are used to adjust the ground pressure of the cutterbar to the local conditions. To protect the sward, the load on the cutterbar must be relieved so that it does not jump during mowing and does not leave any brush marks on the ground either.

The ground pressure of the mower can be adjusted at the perforated bar, the length of the supporting chain and (when using the turnbuckle) at the turnbuckle.

Increasing/reducing ground pressure via perforated bars

96

KM000-376

Borehole (I) = maximum mower relief = minimum ground pressure

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Settings 10

Adjusting the relief spring(s) 10.3

Borehole (VI) =minimum mower relief = maximum ground pressure

ü The machine is in the transport position.

ü

The machine is shut down and safeguarded, see Page 24

.

„ Attach the relief spring (1) in one of the boreholes (I) to (VI).

Attach the relief springs identically on both sides.

Increasing/reducing ground pressure via supporting chains

KM000-377

I) With turnbuckle II) Without turnbuckle

Supporting chain short = high mower relief = low ground pressure

Supporting chain long = low mower relief = high ground pressure

ü The machine is in the transport position.

ü

The machine is shut down and safeguarded, see Page 24

.

„ To increase the ground pressure, extend the supporting chain (1).

„ To reduce the ground pressure, shorten the supporting chain (1).

The supporting chains should have the same length on both sides.

Increasing/reducing ground pressure via turnbuckles

WARNING

Risk of injury due to incorrectly set turnbuckles

If the dimension X=230 mm is exceeded, the thread end of the turnbuckle may tear off and the mower may lower unintentionally. People may be seriously injured or killed, as a result.

„ Never set the turnbuckle to a dimension greater than X = 230 mm .

KM000-378

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 97

10 Settings

10.4

Increasing/reducing ground pressure – mechanical relief adjustment

Reduce dimension X = increased mower relief = lower ground pressure

Increase dimension X = reduced mower relief = higher ground pressure

ü The machine is in the transport position.

ü

The machine is shut down and safeguarded, see Page 24

.

„ Dismount the supporting chain (2) from the turnbuckle (1).

„ To reduce the ground pressure, reduce the dimension X.

„ To increase the ground pressure, increase the dimension X.

„ Mount the supporting chain (2) on the turnbuckle (1).

„ The supporting chains (2) must be attached identically on both sides.

10.4

Increasing/reducing ground pressure – mechanical relief adjustment

For the “trailed” version

1

+

2

KMG000-039

The relief springs (1) are used to adapt the ground pressure of the cutterbar to the local conditions. In order to protect the sward, the cutterbar must be relieved to such an extent that it does not jump when mowing or leave any traces of abrasion on the ground.

The ground pressure of the mower can be adjusted via the threaded spindle (2).

Towards (+) = higher mower relief = lower ground pressure

Towards (-) = lower mower relief = higher ground pressure

ü The machine is in transport position,

see Page 85

.

ü

The machine is shut down and safeguarded, see Page 24

.

„ To reduce the ground pressure, rotate the threaded spindle in direction (+).

„ To increase ground pressure, rotate the threaded spindle in direction (-).

98

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

10.5

Settings 10

Increasing/reducing the ground pressure – hydraulic relief adjustment 10.5

Increasing/reducing the ground pressure – hydraulic relief adjustment

For the “trailed” version

III I

1

KMG000-043

The hydraulic cylinder adjusts the ground pressure of the cutterbar to the local conditions. To protect the sward, the cutterbar must be relieved to such an extent that it does not jump when mowing or leave any traces of abrasion on the ground.

ü The hydraulic hose (1+) is connected to a single-acting control unit.

„ Move the stop cock (1) into position (I),

see Page 84 .

„ Actuate the control unit (1+) until the mower is lowered to working position.

„ Move the stop cock (1) into position (III),

see Page 84

.

„ Actuate the control unit (1+) until the desired relief pressure is displayed on the pressure gauge (2).

Æ The higher the relief pressure, the lower the ground pressure.

Æ The lower the relief pressure, the higher the ground pressure.

2

KMG000-116

The relief pressure can be read off on the pressure gauge (2). Set the ground pressure according to the ground conditions.

Recommended relief pressure: 80...100 bar .

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 99

10 Settings

10.6

Setting the side guards

10.6

II

1

KM000-990

„ Set the stop cock (1) to position (III) when the desired relief pressure is reached.

Setting the side guards

100

KMG000-078

The protective equipment can be adapted to harvesting conditions by adjusting the guards. In order to avoid that crop stalks bend because the guards are too low, set the guards higher. To avoid that stones are slung away when the crops are low, set the guards lower.

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„

Fold up the side guards (1), see Page 81

„ Loosen the screws (4).

„ Set the height of the side guard (1) by means of the console (3).

„ Tighten the screws (4).

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

10.7

Setting conditioner speed

Settings 10

Setting conditioner speed 10.7

10.8

KM000-380

Two conditioner speeds can be set on the belt drive. This affects conditioning effect and power consumption.

Maximum rotational speed: 900 rpm (inner pulleys (1): large pulley top, small pulley bottom)

Minimum rotational speed: 600 rpm (outer pulleys (2): small pulley top, large pulley bottom)

ü

The machine is in the working position, see Page 85 .

ü

The machine is shut down and safeguarded, see Page 24

.

ü The V-belt guard is dismounted,

see Page 114

.

In order to adjust the conditioner speed of the front mounted mower to 900 rpm, position the Vbelt (3) on the two inner pulleys (1).

„ Release the tension on the belt drive on the front mounted mower,

see Page 115

.

„ Position the V-belt (3) on the two inner pulleys (1).

„ Release the tension on the belt drive on the front mounted mower,

see Page 115

.

„ Mount the V-belt guard,

see Page 114

.

In order to adjust the conditioner speed to 600 rpm, position the V-belt (3) on the two outer pulleys (2).

„ Release the tension on the belt drive on the front mounted mower,

see Page 115

.

„ Position the V-belt (3) on the two outer pulleys (2).

„ Release the tension on the belt drive on the front mounted mower,

see Page 115

.

„ Mount the V-belt guard,

see Page 114

.

Setting the degree of conditioning

KMG000-066

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 101

10 Settings

10.9

Setting swath width

The degree of conditioning can be changed by adjusting the conditioning sheet using the lever

(1).

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Adjust the lever (1).

Æ In direction " + ": The distance between the tines and the conditioning sheet is reduced. The degree of conditioning is increased.

Æ In direction " ": The distance between the tines and the conditioning sheet is increased. The degree of conditioning is reduced.

10.9

Setting swath width

II

1

I

2 2

KMG000-050

The swath width can be adapted to the crops.

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

ü

The wide spreading sheet is set all the way down, see Page 103 .

„ Loosen the ring nut (1) on the right-hand and left-hand machine side.

„ Set the swath flaps (2). Perform the same setting on right-hand and left-hand machine side.

ð To the outside (I) = wider swath

ð To the inside (II) = smaller swath

„ Tighten the ring nut (1).

„ Loosen the ring nut (1) on the right-hand and left-hand machine side.

„ Set the swath flaps (2). Perform the same setting on right-hand and left-hand machine side.

ð To the outside (position "I") = wide swath

ð To the inside (position "II") = narrow swath

„ Tighten the ring nut (1).

102

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

10.10

Setting wide spreading

Settings 10

Setting wide spreading 10.10

KM000-279

ü

The machine is shut down and safeguarded, see Page 24

.

Mounting deflector sheets

„ Dismount the swath flaps (1), place them on the machine and secure with the bolts (11) and spring cotter pins (10).

„ In the front part of the deflector sheet (2), insert the coach screw (3) M10x25 from below and tighten it from above with a plastic disc (4), a disc (5) and a palm knob (6).

„ Ensure that the palm knobs are screwed down as tightly as possible, as they can easily get lost due to vibrations.

„ In the rear part of the deflector sheet (2), insert the coach screw (7) M8x20 from below and tighten it from above with a disc (8) and a locknut (9).

Depending on the operating conditions, the deflector sheets (2) may have to be readjusted to ensure equal distribution across the entire area.

10.11

Configure/check the Camera Monitor System

The camera-monitor system must be set so that the road surface is visible up to the horizon, starting to the right resp. left side of the machine.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 103

10 Settings

10.11 Configure/check the Camera Monitor System

KMG100-003

ü

The camera-monitor system has been connected, see Page 73

.

„

Shut down and safeguard the machine, see Page 24

.

„ Switch on the ignition.

„ Switch the monitor on, see the monitor manufacturer's instructions.

„ Call up the divided display mode, see the monitor manufacturer's instructions.

„ Ensure that the cameras are properly connected to the monitor.

Æ The cameras are properly connected if the right-hand side of the divided display shows the picture from the right camera and the left-hand side that from the left camera.

Æ The cameras are not properly connected if the right-hand side of the divided display shows the picture from the left camera and the left-hand side that from the right camera. If the display sides are reversed, change the plugs (CAM1/CAM2),

see Page 73 .

„ Loosen the screws (2) and set the cameras (1) so that the visual field is visible in the monitor, starting at the side of the machine and reaching up to the horizon.

„ Tighten the screws (2).

104

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

11

Maintenance - General Information 11

Maintenance table 11.1

Maintenance - General Information

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of injury caused by test run of the machine

If a test run is performed after repair, maintenance or cleaning work or after technical intervention, the machine may behave unpredictably. Thus there is a risk of serious injuries or death.

ü The machine is in working position.

„ Do not switch on the drives until the mower is resting on the ground and you are absolutely sure that there is no one in the danger zone.

„ The test run of the machine must only be started from the driver's seat.

11.1

11.1.1

Maintenance table

Maintenance – Before the season

Checking oil level

Input gearbox

Main gearbox

Cutterbar

see Page 121

see Page 123

see Page 131

Components

Change/replace blades

Check/replace cutting discs/mower drums

Check/change retaining bolts (blade screw connection)

Check/replace retaining bolts (blade quick fastener)

see Page 127

Only by KRONE service partner, see manual for service technicians

Only by KRONE service partner, see manual for service technicians

Only by KRONE service partner, see manual for service technicians

Check/change blade carrier (blade quick fastener)

Only by KRONE service partner, see manual for service technicians

Check/replace abutting edge on the cutterbar

see Page 130

Vent friction clutch

see Page 111

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 105

11 Maintenance - General Information

11.1

Maintenance table

Components

Check/tension drive belt

Tighten screws/nuts

see Page 115

see Page 107

Check guard cloths

see Page 113

Check the hydraulic hoses for leaks and, if necessary, have them replaced by a KRONE service partner.

see Page 119

Check the electrical connection cables and, if necessary, have them repaired or changed by a KRONE service partner

Checking/setting all the machine settings

see Page 94

11.1.2

Maintenance – After the season

Components

Clean the machine

Lubricate the machine according to the lubrication chart

Lubricate the universal shaft

Release the springs

Grease the threads of the setting screws

Grease the uncoated piston rods of all hydraulic cylinders and insert as far as possible

Lightly coat with oil all those lever joints and bearing positions which cannot be lubricated

Touch up damaged paint and preserve uncoated areas with rust protection agent

Check that all moveable components move freely. If required, dismount, clean, grease and remount.

Park the machine in a weatherproof and dry location which is not in close proximity to corrosive substances

Move the machine every 2 months

see Page 114

see Page 135

see Page 134

11.1.3

Maintenance - Once after 50 hours

Changing oil

Input gearbox

Main gearbox

see Page 121

see Page 123

106

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

11.1.4

Maintenance - General Information 11

Tightening torques 11.2

Maintenance - Every 10 hours, but at least once a day

Checking oil level

Input gearbox

Main gearbox

Cutterbar

see Page 121

see Page 123

see Page 131

Components

Change/replace blades

Check/replace cutting discs/mower drums

Check/change retaining bolts (blade screw connection)

Check/replace retaining bolts (blade quick fastener)

Check/change blade carrier (blade quick fastener)

Check guard cloths

see Page 127

Only by KRONE service partner, see manual for service technicians

Only by KRONE service partner, see manual for service technicians

Only by KRONE service partner, see manual for service technicians

Only by KRONE service partner, see manual for service technicians

see Page 113

11.1.5

Maintenance - Every 50 hours

Components

Tighten screws/nuts

11.1.6

Maintenance - Every 200 hours

Changing oil

Input gearbox

Main gearbox

see Page 107

see Page 121

see Page 123

11.2

Tightening torques

Deviating tightening torques

All screw connections must in general be tightened with the listed tightening torques following.

Deviations from the tables are marked accordingly.

Metric thread screws with control thread

INFO

The table does not apply to countersunk screws with hexagon socket in case the countersunk screw is tightened via hexagon socket.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 107

11 Maintenance - General Information

11.2

Tightening torques

M16

M20

M22

M24

M27

M30

M4

M5

M6

M8

M10

M12

M14

DV000-001

X Thread size

X Strength class

5.6

8.8

Tightening torque (Nm)

3.0

5.9

10

29

42

25

49

85

135

210

425

571

730

1,100

1,450

1 Strength class on screw head

10.9

310

610

832

1,050

1,550

2,100

4.4

8.7

15

36

72

125

200

12.9

365

710

972

1,220

1,800

2,450

5.1

10

18

43

84

145

235

Metric thread screws with fine thread

108

DV000-001

X Thread size 1 Strength class on screw head

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Maintenance - General Information 11

Tightening torques 11.2

X

M12 x 1.5

M14 x 1.5

M16 x 1.5

M18 x 1.5

M20 x 1.5

M24 x 2

M27 x 2

M30 x 1.5

Strength class

5.6

8.8

Tightening torque (Nm)

88

145

222

368

465

787

1,148

800

10.9

130

213

327

525

662

1,121

1,635

2,100

Metric thread screws with countersunk head and hexagon socket

INFO

The table applies only to countersunk screws with hexagon socket and metric thread tightened via hexagon socket.

12.9

152

249

382

614

775

1,312

1,914

2,650

M4

M5

M6

M8

M10

M12

M14

M16

M20

DV000-000

X Thread size

X Strength class

5.6

8.8

Tightening torque (Nm)

2.5

4.7

8

23

34

20

39

68

108

168

340

1 Strength class on screw head

10.9

3.5

7

12

29

58

100

160

248

488

12.9

4.1

8

15

35

67

116

188

292

568

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 109

11 Maintenance - General Information

11.3

Deviating tightening torques

Locking screws on the gearboxes

INFO

The tightening torques only apply to assembly of locking screws, viewing glasses, ventilation and breather filters and bleed valves in gearboxes with cast housings or aluminium or steel housings. The term “locking screw” includes the drain plug, the inspection screw as well as the ventilation and breather filters.

This table applies only to locking screws with external hexagon in connection with copper seal ring and for bleed valves made of brass with shaped seal ring.

Thread

M10x1

M12x1.5

G1/4“

M14x1.5

M16x1.5

45

M18x1.5

50

M20x1.5

Locking screw and sight glass with copper ring 1

Bleed valve made of brass

Ventilation/breather filter made of steel

Steel and cast Aluminium

Ventilation/breather filter made of brass

Steel and cast

Maximum tightening torque (Nm) (±10%)

Aluminium

8

14

14

40

45

16

24

30

32

24

30

G1/2“

M22x1.5

M24x1.5

G3/4“

M33x2

G1“

M42x1.5

G1 1/4“

32

35

60

60

80

80

100

100

1  Always replace copper rings.

11.3

Deviating tightening torques

Screws/nuts

Nut for shear protection (rotary hub)

Bearing housing for cutting disc

Bearing housing for mower drum

Tightening torque

300 Nm

55 Nm

55 Nm

110

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

11.4

Maintenance - General Information 11

Venting the friction clutch 11.4

Venting the friction clutch

NOTICE

Interventions in the friction clutch will lead to a loss of guarantee!

Interventions in the friction clutch change the slip torque. Therefore the machine may be damaged considerably.

„ Never intervene in the overload protection.

„ Only use KRONE original spare parts.

Overloading and brief torque peaks limit the torque and transfer it evenly during slipping.

To guarantee the function, friction clutches must be bled before the initial start-up and after a prolonged standstill. To do this, the friction linings must be relieved and the clutch manually rotated.

The friction clutch is designed with a permanently adjusted turning torque M

R

. The torque is applied to the housing of the friction clutch (2).

Bleeding friction clutch (Walterscheid series K92, K96, K97)

I

1 1

II

1

2

1 1

KM000-899

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Tighten the nuts (1) evenly (I), as a result of which the friction discs are relieved.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Then slacken the nuts (1) again as far as the thread run-out (II).

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 111

11 Maintenance - General Information

11.4

Venting the friction clutch

Bleeding friction clutch (Walterscheid series K90, K94, K92E)

3 1

2

4

KM000-900

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Measure dimension "L" on the compression spring (3) or on the setting screw (1).

„ Loosen the screws (1) or (4), as a result of which the friction discs are relieved.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Set the screws (1) or (4) again to the dimension "L".

Bleeding the friction clutch (Walterscheid series K90/4T)

112

1

2

KM000-988

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Loosen the hexagon nuts (1) evenly but do not dismount them.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Tighten the hexagon nuts (1) evenly.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Venting friction clutch (ByPy)

Maintenance - General Information 11

Checking guard cloths 11.5

11.5

KM000-603

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Loosen the cap nuts (1) uniformly but do not remove them.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Screw in the cap nuts (1) completely.

Checking guard cloths

1 1 1 1

KMG000-010

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„ Carry out a visual inspection of the guard cloth (1) to ensure that there are no cracks and damage.

Æ The machine can be used when there are no cracks or damages.

Æ Replace guard cloths in case of cracks or damage.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 113

11 Maintenance - General Information

11.6

Cleaning the machine

11.6

Cleaning the machine

WARNING

Eye damage caused by flying dirt particles!

When cleaning the machine with compressed air or with high-pressure cleaner, the dirt particles are slung away at high speed. The dirt particles may hit the eyes and hurt them.

„ Keep persons away from working range.

„ When performing cleaning work with compressed air or with high-pressure cleaner, wear suitable working clothes (for example eye protection).

NOTICE

Machine damaged by water from a high-pressure cleaner

Bearings and electric or electronic components can be damaged if you aim the water jet of a high-pressure cleaner directly at them during cleaning.

„ Never direct the water jet of a high-pressure cleaner at bearings, electric/electronic components or safety labels.

„ Replace missing, damaged and unrecognisable safety labels.

ü

The machine has been shut down and secured, see Page 24

.

„ After each use, remove husk and dust from the machine.

11.7

Drive belt

11.7.1

Dismounting/mounting guard

114

KM000-387

ü

The machine is shut down and safeguarded, see Page 24

.

Dismounting

„ Release the locking screw (2) and remove the guard (1).

Mounting

„ Mount the guard (1) and lock the locking screw (2).

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

11.7.2

Maintenance - General Information 11

Drive belt 11.7

Tensioning/relieving belt drive

ü

The machine is shut down and safeguarded, see Page 24

.

ü

The guard is dismounted, see Page 114 .

Relieving belt drive

KM000-381

„ Pull out the linch pin (1).

WARNING! Risk of injury! While relieving the belt drive, the blade key (2) is under spring tension. If the blade key is released too early, it will spring back. While relieving, do not release the blade key.

„ To relieve the belt drive, insert the blade key (2) in the tensioning device (3) and pull it towards the rear.

Tensioning belt drive

KM000-382

WARNING! Risk of injury! While relieving the belt drive, the blade key (2) is under spring tension. If the blade key is released too early, it will spring back. While relieving, do not release the blade key.

„ Slide the blade key (2) into the tensioning device (3).

„ To tension the belt drive, push the blade wrench forward until the tensioning device engages.

„ To secure the tensioning device, insert the linch pin (1) into the borehole.

„ Check the belt tension,

see Page 116

.

„

Mount the guard, see Page 114

.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 115

11 Maintenance - General Information

11.7

Drive belt

11.7.3

Checking/setting belt tension

KM000-383

If the belt drive is tensioned, the display (1) must be closed off flush with the upper edge of the compression spring (2).

ü

The machine is shut down and safeguarded, see Page 24

.

ü

The guard is dismounted, see Page 114 .

ü

The belt drive is tensioned, see Page 115 .

„ Check whether the display (1) ends flush with the upper edge of the compression spring (2).

If the display (1) ends flush with the upper edge of the compression spring (2), the belt tension is correct.

If the display (1) does not end flush with the upper edge of the compression spring (2), the belt tension must be adjusted.

„ Detension the belt drive,

see Page 115

.

„ Loosen the nut (4).

When the display is above the compression spring:

„ Unscrew the sleeve (3) further (turn counterclockwise).

When the display is under the compression spring:

„ Screw the sleeve (3) in further (turn clockwise).

„ Tighten the nut (4).

„ Tension the belt drive,

see Page 115

.

„ Repeat the process until the display (1) ends flush with the upper edge of the compression spring (2) with the belt drive tensioned.

„ Mount the guard (5) of the belt drive,

see Page 114

.

116

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

11.7.4

Checking drive belt for damage

Maintenance - General Information 11

Drive belt 11.7

11.7.5

KM000-386

ü

The machine is shut down and safeguarded, see Page 24

.

ü

The guard is dismounted, see Page 114 .

„ Check the drive belts (1) for cracks and damage.

Æ

In case of cracks or damage, replace the drive belts (1), see Page 117 .

„

Mount the guard, see Page 114

.

Replacing drive belt

KM000-386

ü

The machine is shut down and safeguarded, see Page 24

.

ü

The guard is dismounted, see Page 114 .

„ Release the tension of the belt drive,

see Page 115

.

„ Remove the damaged drive belts (1).

„ Position the new drive belt.

„ Release the tension of the belt drive,

see Page 115

.

„

Mount the guard, see Page 114

.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 117

12 Maintenance - Hydraulic System

12 Maintenance - Hydraulic System

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Hydraulic hoses are subject to ageing

Hydraulic hoses may wear depending on pressure, heat load and the effect of UV rays.

People can be seriously injured or killed by damaged hydraulic hoses.

The date of manufacture appears on the hydraulic hoses. This way the age can be ascertained quickly.

Replacement of the hydraulic hoses is recommended after a lifetime of six years.

„ Use original spare parts when replacing hoses.

NOTICE

Damage to the machine due to soiling of the hydraulic system

If foreign objects or liquids get into the hydraulic system, the hydraulic system may be severely damaged.

„ Clean hydraulic connections and components before removal.

„ Seal open hydraulic connections with protective caps.

„ Ensure that foreign objects or liquids do not get into the hydraulic system.

NOTICE

Storing and disposing of oils and used oil filters

If oil and used oil filters are not stored and disposed of properly, the environment may be damaged.

„ Store or dispose of used oil and oil filters according to statutory provisions.

118

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

12.1

12.2

Maintenance - Hydraulic System 12

Hydraulic oil 12.1

Hydraulic oil

NOTICE

Damage to the hydraulic system caused by non approved hydraulic oils

If non-approved hydraulic oils or a mixture of different oils are used, the hydraulic system may be damaged.

„ Never mix different types of oil.

„ Never use engine oil.

„ Use approved hydraulic oils only.

Filling quantities and types of oil, see Page 50

.

Checking hydraulic hoses

Hydraulic hoses are subject to natural aging. This limits their service life. The recommended service life is 6 years, including a maximum storage time of 2 years. The date of manufacture is printed on the hydraulic hoses. When checking hydraulic hoses, the state-specific conditions

(e.g., BGVU) must be observed.

Performing a visual inspection

„ Visually inspect all hydraulic hoses for damage and leaks and have them replaced by an authorised specialist if necessary.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 119

13 Maintenance - Gearbox

13.1

Overview of gearboxes

13 Maintenance - Gearbox

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

13.1

Overview of gearboxes

I 1 2

II

1 2

3

KMG000-105

I For "Pushed" version

1 Input gearbox

2 Main gearbox

3

3

II For "Trailed" version

Cutterbar

120

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Maintenance - Gearbox 13

Input gearbox 13.2

13.2

Input gearbox

For the “pushed” version

4

1

3

5

2

KM000-391

„ Comply with the safety routine "Safe execution of oil level check, oil and filter element exchange",

see Page 25 .

INFO

The oil level must be checked and the oil must be changed in working position and with machine in horizontal position.

„ Loosen the supporting chain(s) (5).

„ Remove the intermediate universal shaft(s) from the input gearbox.

„ Dismount the guard (4).

Checking the oil level

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„ Remove the locking screw from the inspection hole (1).

ð If the oil reaches the inspection hole (1):

„ Mount the locking screw of the inspection hole (1); tightening torque

see Page 110

.

ð If the oil does not reach the inspection hole (1):

„ Remove the locking screw from the filling hole (3).

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque see Page 110 .

„ Mount the guard (4).

„ Slide the intermediate universal shaft(s) onto the input gearbox and secure it/them.

„ Secure the universal shaft guard(s) with the supporting chain(s) (5) against turning.

Changing the oil

ü A suitable container is available for escaping oil.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 121

13 Maintenance - Gearbox

13.2

Input gearbox

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„ Loosen the supporting chain(s) (5).

„ Remove the intermediate universal shaft(s) from the input gearbox.

„ Dismount the guard (4).

„ Unscrew the locking screw of the inspection hole (1) and the locking screw of the filling hole (3).

„ Unscrew the drain plug (2) and drain the oil.

„

Mount the drain plug (2), tightening torque see Page 110

.

„ Top up with fresh oil via the filling hole (3) up to the inspection hole (1).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque see Page 110 .

„ Mount the guard (4).

„ Slide the intermediate universal shaft(s) onto the input gearbox and secure it/them.

„ Secure the universal shaft guard(s) with the supporting chain(s) (5) against turning.

„ Mount the guard (4).

„ Slide the intermediate universal shaft(s) onto the input gearbox and secure it/them.

„ Secure the universal shaft guard(s) with the supporting chain(s) (5) against turning.

For the “trailed” version

1 3

122

2

KM000-392

INFO

The oil level must be checked and the oil must be changed in working position and with machine in horizontal position.

ü

The machine is shut down and safeguarded, see Page 24

.

Checking the oil level

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„ Remove the locking screw from the inspection hole (1).

ð If the oil reaches the inspection hole (1):

„ Mount the locking screw of the inspection hole (1); tightening torque

see Page 110

.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

13.3

Maintenance - Gearbox 13

Main gearbox 13.3

ð If the oil does not reach the inspection hole (1):

„ Remove the locking screw from the filling hole (3).

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque see Page 110 .

Changing the oil

ü A suitable container is available for escaping oil.

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„ Unscrew the locking screw of the inspection hole (1) and the locking screw of the filling hole (3).

„ Unscrew the drain plug (2) and drain the oil.

„

Mount the drain plug (2), tightening torque see Page 110

.

„ Top up with fresh oil via the filling hole (3) up to the inspection hole (1).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque see Page 110 .

Main gearbox

KMG000-22

„ Comply with the safety routine "Safe execution of oil level check, oil and filter element exchange",

see Page 25 .

INFO

The oil level must be checked and the oil must be changed in working position and with machine in horizontal position.

Checking the oil level

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„ Remove the locking screw from the inspection hole (1).

ð If the oil reaches the inspection hole (1):

„ Mount the locking screw of the inspection hole (1); tightening torque

see Page 110

.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 123

13 Maintenance - Gearbox

13.3

Main gearbox

ð If the oil does not reach the inspection hole (1):

„ Remove the locking screw from the filling hole (3).

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque see Page 110 .

Changing the oil

ü A suitable container is available for escaping oil.

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„ Loosen the supporting chain(s) (5).

„ Remove the intermediate universal shaft(s) from the input gearbox.

„ Dismount the guard (4).

„ Unscrew the locking screw of the inspection hole (1) and the locking screw of the filling hole (3).

„ Unscrew the drain plug (2) and drain the oil.

„

Mount the drain plug (2), tightening torque see Page 110

.

„ Top up with fresh oil via the filling hole (3) up to the inspection hole (1).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque see Page 110 .

„ Mount the guard (4).

„ Slide the intermediate universal shaft(s) onto the input gearbox and secure it/them.

„ Secure the universal shaft guard(s) with the supporting chain(s) (5) against turning.

124

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

14

Maintenance - Cutterbar 14

Maintenance - Cutterbar

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of injury from improper service and maintenance work on safety-relevant machine parts!

Improper service and maintenance work on safety-relevant machine parts, such as cutting discs and mower drums, and the machine components connected to them can cause dangerous imbalances or breakage during operation. As a result, persons can be seriously injured or killed.

„ Always replace damaged safety-relevant components, such as cutting discs and mower drums, and the machine components connected to them.

„ Observe the wear limits and check or replace the components.

„ Never modify any build-up welds.

„ Replace damaged components only with genuine KRONE spare parts.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 125

14 Maintenance - Cutterbar

14.1

Rotary hub

14.1

Rotary hub

A

126

B

KMG000-002

Abbreviations used in this figure:

A = Direction of rotation “A” to the centre

B = Direction of rotation “B” in pairs

RE = eccentric bearing housing (clockwise), without distinctive groove

LE = eccentric bearing housing (rotating anticlockwise), with distinctive groove

For protection against overload of mowers, the rotary hubs (1) are secured with nuts (2) and shear pins (3).

When driving onto obstacles (e.g. stones), the both shear pins in the rotary hub will shear off.

The rotary hub incl. nut turns upward on the pinion shaft.

• The cutting discs or drums which move the crop to the left (LH) in the direction of travel have left-handed thread.

• The cutting discs or drums which transport the crop to the right (RH) in the direction of travel have right-handed thread.

To distinguish between right-hand (clockwise) rotation (RH) and left-hand (anti-clockwise) rotation (LH), the nuts (2) and the pinion shafts (4) for the left-hand rotation (LH) have a distinctive groove (a, b).

• The nuts (2) with left-handed thread (LH) have distinctive grooves (a) on the bevel.

• The pinion shafts (4) with left-handed thread (LH) have a distinctive groove (b) on the face.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

14.2

Maintenance - Cutterbar 14

Check/change blades 14.2

Check/change blades

WARNING

Missing, damaged or incorrectly mounted blades and blade supports

If blades are missing, damaged or incorrectly mounted, dangerous unbalanced rotation may be caused and parts may fly around. People may be seriously injured or killed as a result.

„ Check the blades at least once a day and the retaining bolts every time after changing the blades or after contact with foreign objects.

„ Immediately replace missing, damaged or incorrectly mounted blades and blade supports.

„ To avoid imbalance, always replace missing and damaged blades in kits and never mount unevenly worn blades on a cutting disc/mower drum.

Version with blade screw connection Version with blade quick fastener

14.2.1

KM000-039 / KM000-040

„ Whenever a blade is changed or following contact with foreign objects, check retaining bolts and, if required, have them replaced by authorized specialists.

Checking the blade for wear

WARNING

Risk of injury due to low material thickness on the blades

If the material thickness on the blades is too low, the blades may loosen due to high rotating speed. Thus there is a risk of serious injuries or death.

„ Replace the blades at the latest when the wear limit is reached.

ð The wear limit is reached when the borehole of the blade touches the marking (1) on the blade or the dimension X is equal to or less than 13 mm .

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 127

14 Maintenance - Cutterbar

14.2

Check/change blades

14.2.2

KM000-038

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„

Fold up the front guard, see Page 79

.

WARNING! Risk of injury due to sharp blades! Wear suitable protective gloves.

„ Clean the area around the blades, cutting discs and mower drums.

„ Check wear limit.

ð If the dimension is X>13 mm , the wear limit is not reached.

ð If the dimension X is ≤13 mm or the borehole touches the marking (1), the blade must be replaced.

„

Fold down the front guard, see Page 79

.

Changing blades for the “blade screw connection” version

128

KM000-044

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„

Fold up the front guard, see Page 79

.

WARNING! Risk of injury due to sharp blades! Wear suitable protective gloves.

„ Clean the area around the blades, cutting discs and mower drums.

„ Remove the damaged or worn blade.

„ Check the fastening parts of the blade. Also replace worn or damaged fastening parts.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Maintenance - Cutterbar 14

Check/change blades 14.2

INFO: The blades for anti-clockwise and clockwise rotating cutting discs/mower drums differ.

When installing the blades, ensure that the direction of rotation is correct. The arrow on the blade must match the direction of rotation of the corresponding cutting disc/mower drum.

„ Insert the new blade (5) between the wear skid (2) and the cutting disc (1).

„ Insert the retaining bolt (3) from below through the wear skid (2), the blade (5) and the cutting disc (1).

INFO: Only use the locknut (4) once.

„ Screw the locknut (4) from above onto the retaining bolt (3) and tighten it; tightening torque

see Page 107

.

„ Repeat the process for all blades.

„

Fold down the front guard, see Page 79

.

INFO

Clockwise rotating blades can be ordered by stating order number 00 139 889 *.

Anticlockwise rotating blades can be ordered by stating order number 00 139 888 *.

14.2.3

Changing blades for the “blade quick fastener” version

1

2 3

4

4

5

2

3

KM000-045

ü

The machine is in the working position, see Page 85 .

ü

The machine has been shut down and secured, see Page 24

.

„

Fold up the front guard, see Page 79

.

WARNING! Risk of injury due to sharp blades! Wear suitable protective gloves.

„ Clean the area around the blades, cutting discs and mower drums.

„ To remove the blade (2), insert the blade wrench (1) between the cutting disc (4) and the blade carrier (3) as far as it will go, press it down with one hand and hold it.

„ Check the fastening parts of the blade (2). Also replace worn or damaged fastening parts.

INFO: The blades for anti-clockwise and clockwise rotating cutting discs/mower drums differ.

When installing the blades, ensure that the direction of rotation is correct. The arrow on the blade must match the direction of rotation of the corresponding cutting disc/mower drum.

„ To insert the new blade (2), insert the blade key (1) between the cutting disc (4) and the blade carrier (3) as far as it will go, press it down with one hand and hold it.

„ Guide the blade (2) onto the retaining bolt (5) and release the blade key (1) in a controlled manner with your hand.

„ Repeat the process for all blades.

„

Fold down the front guard, see Page 79

.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 129

14 Maintenance - Cutterbar

14.3

Checking/replacing linings on cutterbar

INFO

Alternatively, the blades can be changed with the QuickChange tool.

INFO

Clockwise rotating blades can be ordered by stating order number 00 139 889 *.

Anticlockwise rotating blades can be ordered by stating order number 00 139 888 *.

14.3

Checking/replacing linings on cutterbar

NOTICE

Impact stops are checked irregularly

The impact stops are subject to natural wear and must be inspected daily for wear and replaced if required. If there is no inspection, the machine may be damaged.

„ Adjust the welding current and the welding material to the cutterbar material and to the impact stop. If required, carry out a test weld.

KM000-081

„ Open the welding seams of the old lining.

„ Remove lining.

„ Deburr the contact areas.

130

KM000-080

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

14.4

Maintenance - Cutterbar 14

Checking oil level 14.4

„ Fit the new lining (3).

„ Weld short I seams on the upper side of the cutterbar in the sections (1) (each should be approx. 30 mm). INFORMATION: The edges (2) must not be welded.

„ On the bottom of the cutterbar, weld the lining (3) to the cutterbar along the whole length in section (5). INFORMATION: The edges (4) must not be welded.

Checking oil level

INFO

There is no need to change the oil on the cutterbar.

Before checking the oil level on the cutterbar, level the cutterbar using a spirit level.

KM000-284

NOTE! Risk of machine damage due to improperly performed oil level check, oil and filter element change! Follow the safety routine "Oil level check. Changing oil and filter elements safely",

see Page 25

.

„

Shut down and safeguard the machine, see Page 24

.

Aligning the cutterbar in transverse direction (direction of travel)

„ Position the spirit level (1) transversely on the cutterbar.

„ Align the cutterbar using the spirit level (1) and readjust, if necessary, via cutting height

setting, see Page 94 .

Aligning the cutterbar in longitudinal direction

„ Position the spirit level (1) on two cutting discs.

„ Use the spirit level (1) to align the cutterbar, if necessary use wedges to align it horizontally.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 131

14 Maintenance - Cutterbar

14.4

Checking oil level

Checking oil level

KM000-036

„ Release the locking screw of the inspection hole (1).

ð The oil level must reach up to the inspection hole (1).

If the oil reaches the inspection hole (1):

„

Mount the locking screw of the inspection hole (1), see Page 110

.

If the oil does not reach the inspection hole (1):

„ Top up new oil via the inspection hole (1) up to the inspection hole (1).

„

Mount the locking screw of the inspection hole (1), see Page 110

.

132

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

15

Maintenance – Lubrication 15

Maintenance – Lubrication

NOTICE

Bearing positions will be damaged

If different lubricating greases are used, the lubricated components may be damaged.

„ Do not use lubricating greases which contain graphite.

„ Do not use different lubricating greases.

NOTICE

Environmental damage caused by consumables

If consumables are not stored and disposed of properly, they may escape into the environment. As a result, the environment will be damaged, even by small quantities.

„ Store the consumables in suitable containers according to the statutory provisions.

„ Dispose of used consumables according to statutory provisions.

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 133

15 Maintenance – Lubrication

15.1

Lubricating universal shaft

15.1

Lubricating universal shaft

Lubricate universally-jointed drive shaft

100h 100h

250h 250h

KMG000-007

ü

The machine has been shut down and secured, see Page 24

.

„ Observe operating instructions of the universal shaft manufacturer.

„ Lubricate the universal shaft with multi-purpose grease at the intervals indicated in the figure.

Lubricating intermediate universal shaft

134

KMG000-069

ü

The machine is shut down and safeguarded, see Page 24

.

„ Observe operating instructions of the universal shaft manufacturer.

„ Lubricate the universal shaft with multi-purpose grease at the intervals indicated in the figure.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

15.2

Maintenance – Lubrication 15

Lubrication chart – Machine 15.2

Lubrication chart – Machine

The information on maintenance intervals is based on average load of the machine. In case of an increased load and under extreme working conditions, the time periods must be reduced.

The types of lubrication are marked by means of icons in the lubrication chart, refer to table.

Type of lubrication

Grease

Lubricant

Multi-purpose grease

Comment

„ Apply two strokes of lubricating grease from the grease gun per grease nipple.

„ Remove excess lubricating grease at the grease nipple.

KMG000-008

I "Pushed" version

Every 50 operating hours

1) 2)

II "Trailed" version

Additional lubrication points for the “trailed” version

Every 50 operating hours

3) 4) 5)

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 135

16 Malfunction, cause and remedy

16.1

General disturbances

16 Malfunction, cause and remedy

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

16.1

General disturbances

Disturbance: The cutting quality is not adequate.

Possible cause

The cutting height has been set too high.

The rotational speed is too low.

The blades are blunt.

Remedy

„ Reduce the cutting height,

see Page 94

.

„

„

Increase the rotational speed.

Change the blades,

see Page 127

.

Disturbance: The mower cannot be adjusted to the unevenness of the ground.

Possible cause

The tractor hydraulics is not in the float position.

Remedy

„ Set tractor hydraulics to float position,

see Page 52 .

Disturbance: The forage contamination is high.

Possible cause

Relief is too weak.

Remedy

„ Increase the relief,

see Page 96

.

Malfunction: The swath width is too large.

Possible cause

The swath flaps are too far outwards.

Remedy

„ Set the swath width,

see Page 102

.

136

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

17

Waste disposal 17

Waste disposal

After the service life of the machine has expired, the individual components of the machine must be disposed of properly. The currently applicable country-specific waste disposal directives and the concerning valid laws must be observed.

Metal parts

• All metal parts must be brought to a metal recycling centre.

• The parts must be freed from operating fluids and lubricants (gearbox oil, oil from hydraulic system, ...) before being scrapped.

• The operating fluids and lubricants must be brought separately to an environmentally friendly disposal point or recycling centre.

Operating fluids and lubricants

• Operating fluids and lubricants (diesel fuel, coolant, gearbox oil, oil from hydraulic system,

…) must be brought to a disposal point for waste oil.

Synthetic materials

• All synthetic materials must be brought to a recycling centre for synthetic materials.

Rubber

• Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre.

Electronic scrap

• All electronic parts must be brought to a disposal point for electronic scrap.

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 137

Index

A

Adapting coupling points .................................... 56

Adapting universal shaft ..................................... 54

Additional equipment and spare parts ................ 14

Adjusting the relief spring(s) ............................... 96

Airborne noise emission ..................................... 49

Ambient temperature .......................................... 50

Applicable documents .......................................... 6

Area output ......................................................... 49

Attaching the relief springs with a turnbuckle ..... 69

B

Basic safety instructions ..................................... 13

Basic setting of mower ....................................... 77

Behavior in the case of voltage flashover of

overhead lines .................................................... 21

Behaviour in dangerous situations and in case of

accidents ............................................................ 24

138

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Index

C

Calculating the ballasting of the tractor-machine

combination ........................................................ 60

Carrying out oil level check and oil and filter

element changes safely...................................... 25

Changing blades for the “blade quick fastener”

version .............................................................. 129

Changing blades for the “blade screw connection”

version .............................................................. 128

Changing the oil ............................... 121, 123, 124

Check clearance................................................. 66

Check/change blades ....................................... 127

Checking drive belt for damage........................ 117

Checking front end dimension ............................ 75

Checking guard cloths ...................................... 113

Checking hydraulic hoses ................................ 119

Checking internal chains for overstretching ....... 70

Checking locking device and latch ..................... 76

Checking oil level ............................................. 131

Checking the blade for wear............................. 127

Checking the tines on the tine conditioner ......... 76

Checking/replacing linings on cutterbar ........... 130

Checking/setting belt tension ........................... 116

Checking/setting parallel lifting ........................... 67

Checklist for initial operation .............................. 53

Checklist for the transport of the machine .......... 92

Children in danger .............................................. 14

Cleaning the machine....................................... 114

Commissioning ................................................... 53

Configure/check the Camera Monitor System.. 103

Connect the Camera Monitor System ................ 73

Connecting hydraulic hoses ............................... 71

Connecting machine to tractor ........................... 65

Connecting road travel lighting ........................... 72

Connecting the machine..................................... 14

Consumables ............................................... 20, 50

Contact ................................................................. 2

Contact data of your dealer .................................. 2

Contamination of hydraulic system and/or fuel

system ................................................................ 20

Control and Display Elements ............................ 52

Conversion table .................................................. 9

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Cross references .................................................. 6

Cutting height ..................................................... 49

D

Damaged hydraulic hoses .................................. 22

Danger associated with welding work ................ 24

Danger resulting from damage to the machine .. 15

Danger when cornering with a hitched machine

and due to the overall width ............................... 19

Danger when driving on road and field............... 19

Danger zone between tractor and machine ....... 17

Danger zone due to trailing machine parts......... 17

Danger zone ejected objects .............................. 17

Danger zone PTO shaft...................................... 17

Danger zone universal shaft............................... 16

Danger zone when drive is switched on ............. 17

Danger zones ..................................................... 16

Dangers arising from environment ..................... 21

Dangers during road travel ................................. 19

Dangers if the machine is not prepared properly for

road travel .......................................................... 19

Dangers in connection with certain activities:

Working on the machine..................................... 23

Dangers when operating the machine on slopes 20

Declaration of conformity.................................. 143

Deviating tightening torques ............................. 110

Dimensions......................................................... 49

Directories and references ................................... 6

Dismounting/mounting guard ........................... 114

Drive belt .......................................................... 114

Driving and Transport ......................................... 88

E

Ensuring functionality of safety devices ............. 18

Environmental protection and disposal .............. 21

139

Index

F

Field mode.......................................................... 86

Figures ................................................................. 7

Fire hazard ......................................................... 21

Fold down the front guard .................................. 80

Folding down the side guard - for "Series" version

(working position) ............................................... 81

Folding down the side guard – in version

"hydraulically folding side guards" (working

position) .............................................................. 82

Folding up the front guard .................................. 79

Folding up the side guard - for "Series" version

(transport position) ............................................. 81

Folding up the side guard – in version

"hydraulically folding side guards" (transport

position) .............................................................. 82

Front guard ......................................................... 79

G

General disturbances ....................................... 136

H

Hot liquids........................................................... 22

Hot surfaces ....................................................... 23

How to use this document .................................... 6

Hydraulic control units of the tractor ................... 52

Hydraulic oil ...................................................... 119

140

I

Icons in figures ..................................................... 7

Icons in the text .................................................... 7

Importance of operating instructions .................. 13

Increasing/reducing ground pressure via

perforated bars ................................................... 96

Increasing/reducing ground pressure via

supporting chains ............................................... 97

Increasing/reducing ground pressure via

turnbuckles ......................................................... 97

Increasing/reducing ground pressure – mechanical

relief adjustment ................................................. 98

Increasing/reducing the ground pressure –

hydraulic relief adjustment.................................. 99

Information for enquiries and orders .............. 2, 48

Information labels on the machine ..................... 35

Information on direction ........................................ 7

Information on This Document ............................. 6

Input gearbox ................................................... 121

Installing universal shaft ..................................... 74

Intended use....................................................... 12

Intermediate universal shaft ............................... 48

J

Jobs on the machine .......................................... 15

L

Labelling ............................................................. 47

Lashing the machine .......................................... 93

Lifting the machine ............................................. 92

Liquids under high pressure ............................... 22

Location and meaning of the information labels . 36

Locking screws on the gearboxes .................... 110

Locking/releasing stop cock ............................... 84

Lower link pins.............................................. 56, 58

Lowering machine from transport position to

working position.................................................. 85

Lubricate universally-jointed drive shaft ........... 134

Lubricating greases ............................................ 51

Lubricating intermediate universal shaft ........... 134

Lubricating universal shaft................................ 134

Lubrication chart – Machine ............................. 135

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

Index

M

Machine Description ........................................... 45

Machine equipment ............................................ 50

Machine overview............................................... 45

Main gearbox.................................................... 123

Maintenance – After the season....................... 106

Maintenance – Before the season.................... 105

Maintenance - Cutterbar................................... 125

Maintenance - Every 10 hours, but at least once a

day.................................................................... 107

Maintenance - Every 200 hours ....................... 107

Maintenance - Every 50 hours ......................... 107

Maintenance - Gearbox .................................... 120

Maintenance - General Information .................. 105

Maintenance - Hydraulic System...................... 118

Maintenance – Lubrication ............................... 133

Maintenance - Once after 50 hours .................. 106

Maintenance and repair work ............................. 23

Maintenance table ............................................ 105

Malfunction, cause and remedy ....................... 136

Means of representation....................................... 7

Metric thread screws with control thread .......... 107

Metric thread screws with countersunk head and

hexagon socket ................................................ 109

Metric thread screws with fine thread ............... 108

Mounting lighting system .................................... 55

Mounting lower link extension ............................ 66

Mounting relief springs ....................................... 68

Mounting the universal shaft on the machine ..... 55

Mounting top link fork ......................................... 64

Moving support jack into support position .......... 83

Moving support jack into transport position ........ 83

N

Noise may damage your health.......................... 22

Notes with information and recommendations ..... 9

O

Oils ..................................................................... 51

Only perform work when the machine is at

standstill ............................................................. 23

Operating support jack ....................................... 82

Operating the Camera Monitor System .............. 87

Operating the stop cock ..................................... 84

Operation............................................................ 79

Operation only after proper commissioning........ 15

Operational safety: Technically sound condition 15

Overload protections on the machine................. 47

Overview of gearboxes..................................... 120

P

Parking the machine........................................... 90

Parking the machine safely ................................ 20

Passengers ........................................................ 15

Performing a visual inspection ......................... 119

Personal protective equipment ........................... 18

Personnel qualification of the operating personnel

........................................................................... 13

Personnel qualification of the technicians .......... 14

Position and meaning of safety labels ................ 28

Preparing the machine for road travel ................ 89

Preparing the machine for shipment .................. 91

Preparing tractor................................................. 63

R

Raised machine and machine parts ................... 23

Raising machine from working position to transport

position ............................................................... 85

Reasonably foreseeable misuse ........................ 12

Re-ordering .......................................................... 6

Replacing drive belt .......................................... 117

Requirements for the tractor – electrics ............. 50

Requirements for tractor - power........................ 50

Road safety ........................................................ 19

Rotary hub ........................................................ 126

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 141

Index

S

Safety ................................................................. 12

Safety features ................................................... 43

Safety Labels on the Machine ............................ 26

Safety markings on the machine ........................ 19

Safety routines ................................................... 24

Scope of the document ........................................ 7

Securing raised machine and machine parts

against lowering ................................................. 25

Service life of the machine ................................. 13

Setting conditioner speed ................................. 101

Setting swath width .......................................... 102

Setting the cutting height .................................... 94

Setting the degree of conditioning .................... 101

Setting the side guards..................................... 100

Setting wide spreading ..................................... 103

Settings .............................................................. 94

Shutting down and safeguarding the machine ... 24

Side guard - for the “series” version ................... 80

Side guard - for version with “hydraulically folding

side guards”........................................................ 81

Sources of danger on the machine .................... 22

Start-up............................................................... 60

Structural modifications on the machine ............ 14

T

Target group of this document ............................. 6

Technical data .................................................... 49

Technical limit values ......................................... 16

Technically permitted maximum speed (road

travel) ................................................................. 49

Technically sound state of the machine ............. 15

Telescopic top link .............................................. 95

Tensioning/relieving belt drive .......................... 115

Term “machine” .................................................... 7

Tightening guard cloth ........................................ 74

Tightening torques............................................ 107

Top link pin ................................................... 57, 58

Tractor requirements – hydraulics ...................... 50

U

universal shaft .................................................... 54

Unsuitable consumables .................................... 20

V

Validity .................................................................. 6

Venting the friction clutch ................................. 111

W

Warning signs....................................................... 8

Warnings of property damage/environmental

damage ................................................................ 9

Waste disposal ................................................. 137

Weights .............................................................. 49

Working at or on heights of the machine ............ 23

142

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb

18

Declaration of conformity 18

Declaration of conformity

UKCA Declaration of Conformity

We

KRONE Agriculture SE

Heinrich-Krone-Straße 10, D-48480 Spelle hereby declare, as manufacturer of the product named below, under our sole responsibility, that the

Machine:

Type:

Front mounted mowers

EasyCut F 320 CV to which this declaration refers is in compliance with the following relevant provisions of:

• Supply of Machinery (Safety) Regulations 2008, 2008 No. 1597

The signing Managing Director is authorised to compile the technical documents.

Spelle, 04/08/2021

Year of manufacture:

Importer and authorised representative:

Krone UK Ltd.

Phoenix Avenue

Micklefield, Leeds LS25 4DY

Jan Horstmann

(Managing Director, Design & Development)

Machine no.:

EasyCut F 320 CV

Original operating instructions 150000173_08_en-gb 143

Maschinenfabrik

Bernard Krone GmbH & Co. KG

* Heinrich-Krone-Straße 10

D-48480 Spelle

* Postfach 11 63

D-48478 Spelle

' +49 (0) 59 77 / 935-0

6 +49 (0) 59 77 / 935-339

ü

www.landmaschinen.krone.de

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement

Table of contents