Krone EasyCut B 870 CV Operating Instructions


Add to my manuals
114 Pages

advertisement

Krone EasyCut B 870 CV Operating Instructions | Manualzz

Original Operating Instructions

Document no.: 150000705_01_ us

Mower Combination

EasyCut B 870 CV

From machine no.: 976393

Contact

Mailing address

Krone North America, Inc.

P.O. Box 18880

Memphis, TN 38181-0880

USA

Phone

Fax

E-mail

Internet

Physical address

Krone North America, Inc.

3363 Miac Cove

Memphis, TN 38118

USA

+1 901 842-6011

+1 901 842-6016 [email protected]

www.krone-northamerica.com

Information for enquiries and orders

Year

Machine no.

Type

Contact data of your dealer

2

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Contents

3

3.1

3.2

3.3

3.4

3.5

4

4.1

4.1.1

4.1.2

5

5.1

6

2

2.4.10

2.4.11

2.4.12

2.4.13

2.4.14

2.4.15

2.4.16

2.4.17

2.4.18

2.4.19

2.4.20

2.5

2.5.1

2.5.2

2.5.3

2.6

2.7

2.7.1

2.1

2.2

2.3

2.4

2.4.1

2.4.2

2.4.3

2.4.4

2.4.5

2.4.6

2.4.7

2.4.8

2.4.9

1

1.1

1.2

1.3

1.4

1.5

1.5.1

1.5.2

1.5.3

1.5.4

1.5.5

1.5.6

1.5.7

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Information on This Document.................................................................................................  6

Validity .........................................................................................................................................  6

Re-ordering ..................................................................................................................................  6

Applicable documents..................................................................................................................  6

Target group of this document .....................................................................................................  6

How to use this document ...........................................................................................................  6

Directories and references...........................................................................................................  6

Information on direction ...............................................................................................................  7

Term “machine”............................................................................................................................  7

Figures .........................................................................................................................................  7

Scope of the document ................................................................................................................  7

Means of representation ..............................................................................................................  7

Conversion table ..........................................................................................................................  9

Safety ........................................................................................................................................  12

Intended use ..............................................................................................................................  12

Reasonably foreseeable misuse................................................................................................  12

Service life of the machine.........................................................................................................  13

Basic safety instructions ............................................................................................................  13

Importance of operating instructions..........................................................................................  13

Personnel qualification of the operating personnel ....................................................................  13

Personnel qualification of the technicians..................................................................................  14

Children in danger .....................................................................................................................  14

Connecting the machine ............................................................................................................  14

Structural modifications on the machine ....................................................................................  14

Additional equipment and spare parts .......................................................................................  14

Jobs on the machine..................................................................................................................  15

Operational safety: Technically sound condition .......................................................................  15

Danger zones ............................................................................................................................  16

Ensuring functionality of safety devices .....................................................................................  18

Personal protective equipment ..................................................................................................  18

Safety markings on the machine ...............................................................................................  18

Road safety................................................................................................................................  19

Parking the machine safely .......................................................................................................  20

Consumables .............................................................................................................................  20

Dangers arising from environment.............................................................................................  20

Sources of danger on the machine ............................................................................................  21

Dangers in connection with certain activities: Working on the machine ....................................  23

Behaviour in dangerous situations and in case of accidents .....................................................  24

Safety routines ...........................................................................................................................  24

Shutting down and safeguarding the machine...........................................................................  24

Securing raised machine and machine parts against lowering..................................................  24

Carrying out oil level check and oil and filter element changes safely.......................................  25

Safety Labels on the Machine ...................................................................................................  25

Safety equipment .......................................................................................................................  30

SMV emblem .............................................................................................................................  31

Machine description ................................................................................................................  32

Machine overview ......................................................................................................................  32

Labelling ....................................................................................................................................  33

Lighting ......................................................................................................................................  33

Intermediate universal shaft.......................................................................................................  33

Pole protection mechanism .......................................................................................................  34

Technical data ..........................................................................................................................  35

Consumables .............................................................................................................................  36

Oils.............................................................................................................................................  36

Lubricating greases ...................................................................................................................  36

Control and Display Elements ................................................................................................  37

Operation panel .........................................................................................................................  37

Initial operation ........................................................................................................................  39

3

Contents

12

13

13.1

13.2

14

9

9.1

9.2

10

10.1

10.2

10.3

10.4

10.5

10.6

10.7

10.8

10.9

10.10

10.10.1

11

11.1

11.1.1

11.1.2

11.1.3

11.1.4

11.1.5

11.1.6

11.2

11.3

11.4

11.5

6.1

6.2

6.3

7

7.1

7.2

7.3

7.4

7.5

7.6

8

8.1

8.1.1

8.1.2

8.2

8.2.1

8.2.2

8.3

8.3.1

8.3.2

8.4

8.5

8.6

8.7

Checklist for initial operation ......................................................................................................  39

Adapting Coupling Points ..........................................................................................................  40

Adapting universal shaft ............................................................................................................  41

Start-up .....................................................................................................................................  42

Connecting the machine to the tractor .......................................................................................  42

Connecting hydraulic hoses.......................................................................................................  43

Connecting operation panel .......................................................................................................  44

Connecting road travel lighting ..................................................................................................  45

Installing universal shaft ............................................................................................................  45

Checking the tines on the tine conditioner .................................................................................  46

Operation ..................................................................................................................................  47

Front guard ................................................................................................................................  47

Folding up the front guard..........................................................................................................  48

Fold down the front guard ..........................................................................................................  48

Side guard .................................................................................................................................  49

Folding up side guard (transport position) .................................................................................  49

Folding down side guard (working position) ..............................................................................  49

Operate the support jack ...........................................................................................................  50

Move parking jacks into transport position.................................................................................  50

Move parking jacks into support position ...................................................................................  50

Locking / releasing stop cocks ...................................................................................................  51

Lowering the machine from transport position to working position ............................................  51

Mowing.......................................................................................................................................  52

Field mode on slopes.................................................................................................................  53

Driving and transport ..............................................................................................................  54

Prepare the machine for road travel ..........................................................................................  55

Switching off the machine ..........................................................................................................  55

Settings.....................................................................................................................................  57

Setting the cutting height ...........................................................................................................  57

Setting the lateral links...............................................................................................................  58

Adjusting the relief spring(s) ......................................................................................................  58

Increasing/reducing ground pressure ........................................................................................  60

Setting the side guards ..............................................................................................................  60

Checking/setting locking of side guards ....................................................................................  61

Setting the conditioner speed ....................................................................................................  62

Setting the degree of conditioning .............................................................................................  62

Setting the swathing ..................................................................................................................  63

Setting wide spreading ..............................................................................................................  64

Setting widespreading sheet......................................................................................................  64

Maintenance - General Information........................................................................................  66

Maintenance table .....................................................................................................................  66

Maintenance - Once after 50 hours ...........................................................................................  66

Maintenance - Before the beginning of the season ...................................................................  66

Maintenance - Every 10 hours, but at least once a day.............................................................  67

Maintenance - Every 50 hours ...................................................................................................  67

Maintenance - Every 200 hours .................................................................................................  67

Maintenance - Every 6 years .....................................................................................................  67

Tightening torques .....................................................................................................................  68

Deviating tightening torques ......................................................................................................  71

Venting the friction clutch...........................................................................................................  71

Checking guard cloths ...............................................................................................................  72

Maintenance - Hydraulic System............................................................................................  73

Maintenance - Gearbox ...........................................................................................................  74

Input gearbox .............................................................................................................................  74

Main gearbox .............................................................................................................................  75

Maintenance - Cutterbar..........................................................................................................  77

4

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

16

17

18

18.1

19

14.1

14.2

14.3

14.3.1

14.3.2

14.3.3

14.4

14.5

14.6

14.6.1

14.7

14.8

15

15.1

15.2

Contents

Rotary hub .................................................................................................................................  77

Replacing the shear bolt at the rotary hub .................................................................................  78

Check/change blades ................................................................................................................  79

Checking the blade for wear ......................................................................................................  79

Changing blades for the “blade screw connection” version .......................................................  80

Changing blades for the “blade quick fastener” version ............................................................  81

Checking/replacing retaining bolts .............................................................................................  82

Checking/replacing blade carrier ...............................................................................................  83

Checking/replacing cutting discs/mower drums.........................................................................  85

Checking the wear limit on cutting discs/mower drums .............................................................  86

Checking/replacing linings on cutterbar .....................................................................................  86

Checking oil level .......................................................................................................................  87

Maintenance - Lubrication ......................................................................................................  90

Lubricating universal shaft .........................................................................................................  90

Lubrication chart - Machine .......................................................................................................  91

Storage......................................................................................................................................  94

Waste disposal.........................................................................................................................  96

Appendix ..................................................................................................................................  97

Circuit diagram...........................................................................................................................  97

Index........................................................................................................................................  109

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 5

1

1.1

1

Information on This Document

Validity

Information on This Document

1.1

1.2

1.3

1.4

1.5

1.5.1

Validity

This document is valid for machines of type:

EasyCut B 870 CV

This document only describes the rear combination. If the combination is used with front mounted mower, the operating instructions of the front mounted mower must also be considered.

All information, illustrations and technical data in this document correspond to the latest state at the time of publication.

We reserve the right to make design changes at any time and without notification of reasons.

Re-ordering

If this document has become unusable in whole or in part, you can order a replacement, quoting the document number on the cover sheet. The document can additionally be downloaded via the KRONE Media Center http://www.mediathek.krone.de// .

Applicable documents

To ensure that the machine is used safely and as intended, observe the following further applicable documents.

• Operating instructions for universal shaft

• With front mounted mower: Operating instructions front mounted mower

• Assembly instructions, KRONE

Target group of this document

This document aims at the operator of the machine who fulfills the minimum requirements of personnel qualification,

refer to page 13

.

How to use this document

Directories and references

Contents/headers

The contents and headers in this document ensure quick orientation in the chapters.

Index

The index contains catchwords in alphabetical order which enable to find information on a desired topic easily. The index can be found on the last pages of this document.

Cross references

Cross references to another place in the document or to another document are in the text with page number.

6

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

1.5.2

1.5.3

1.5.4

1.5.5

1.5.6

Information on This Document

How to use this document

Examples:

• Check all screws on the machine for firm attachment,

refer to page 7

. ( INFORMATION : If you use this document in electronic form, you get to the link to the stated page by clicking with the mouse.)

• For further information, refer to the operating instructions of the universal shaft manufacturer.

1

1.5

Information on direction

Directional information in this document, such as front, rear, right and left, applies in the direction of travel of the machine.

Term “machine”

Throughout the rest of the document, the “mower combination” will also be referred to as the

“machine”.

Figures

The figures in this document do not always represent the exact machine type. The information that refers to the figure always corresponds to the machine type of this document.

Scope of the document

In addition to standard equipment, accessories kits and versions of the machine are described in this document. Your machine may deviate from this document.

Means of representation

Icons in the text

The following means of representation (icons) are used to present the text more clearly:

This arrow characterizes an action step . Several arrows in a row identify a sequence of actions to be performed step by step.

This icon identifies a prerequisite that has to be fulfilled to perform an action step or a sequence of actions.

This arrow marks the intermediate result of an action step.

This arrow identifies the result of an action step or sequence of actions.

This bullet point identifies an enumeration . If the bullet point is intended, it identifies the second level of the enumeration.

Icons in figures

The following icons can be used in illustrations:

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 7

8

1

1.5

Information on This Document

How to use this document

Icon Explanation

Reference sign for part

Dimensions (e. g. also B = width,

H = height, L = length)

Left-hand side of the machine

Icon

Direction of travel

Reference line for visible material

Centre line

Tighten screws according to tightening torques table open

Apply liquid lubricant (e.g. lubricating oil)

Explanation

Position of a part (e.g. move from position I to position II)

Magnification of display detail

Right-hand side of the machine side

Moving direction

Reference line for covered material

Cable routes

Tighten screws with specified tightening torque closed

Apply lubricating grease

Warning signs

Warnings of dangers are separated from the remaining text as warning signs and are identified with a danger sign and signal words.

The warning signs must be read and the measures must be observed in order to prevent personal injury.

Explanation of danger sign

This is the danger sign that warns of a risk of injury.

Please observe all notes marked with the danger sign in order to avoid injuries or death.

Explanation of signal words

DANGER

The signal word DANGER warns of a hazardous situation which will result in serious injuries or death if the warning sign is ignored.

WARNING

The signal word WARNING warns of a hazardous situation which will result in serious injuries or death if the warning sign is ignored.

CAUTION

The signal word CAUTION warns of a hazardous situation which will result in minor to moderate injuries if the warning sign is ignored.

Example of a warning sign:

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

1.5.7

Information on This Document

How to use this document

1

1.5

WARNING

Eye damage caused by flying dirt particles

When cleaning with compressed air, dirt particles are ejected at high speed and could get into the eyes. Therefore eyes could be hurt.

„ Keep people away from the working area.

„ Wear personal protective equipment when performing cleaning work with compressed air

(e.g. eye protection).

Warnings of property damage/environmental damage

Warnings of property/environmental damage are separated from the remaining text and marked with "Notice".

Example:

NOTICE

Gearbox damage due to low oil level

The gearboxes could be damaged when the oil level is too low.

„ Check gear oil level at regular intervals and top up oil, if necessary.

„ Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check oil level only when machine is in horizontal position.

Notes with information and recommendations

Additional information and recommendations for trouble-free and productive operation of the machine are separated from the remaining text and marked with “Information”.

Example:

INFORMATION

Each safety label is provided with an order number and can be ordered directly from the manufacturer or from the authorized specialist dealer.

Conversion table

The following table can be used to convert metric units into US units.

Size

Area

Volume flow Litres per minute L/min

Cubic metres per hour m³/h

Force

Length

Power

SI units (metric)

Unit name Abbreviation

Hectare ha

Newton

Millimetre

Metre

Kilowatt

N mm m kW

Factor

2.47105

0.2642

4.4029

0.2248

0.03937

3.2808

1.3410

Inch-pound units

Unit name

Acre

US gallons per minute

Pound force

Inch

Foot

Horsepower

Abbreviation acres gpm lbf in.

ft.

hp

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 9

1

1.5

Information on This Document

How to use this document

Size

Pressure

Torque

SI units (metric)

Unit name Abbreviation

Kilopascal kPa

Megapascal bar (non-SI)

Newtonmeter

MPa bar

Nm

Factor

0.1450

145.0377

14.5038

0.7376

Temperature Degrees Celsius °C

Velocity

Volumes

Weight

Metres per minute

Metres per second

Kilometres per hour

Litres

Millilitre

Cubic centimetre

Kilogram m/min m/s km/h

L ml cm³ kg

8.8507

°Cx1.8+32

3.2808

3.2808

0.6215

0.2642

0.0338

0.0610

2.2046

Inch-pound units

Unit name Abbreviation

Pounds per square inch psi pound-foot or foot-pound ft∙lbf pound-inch or inch-pound

Degrees

Fahrenheit in∙lbf

°F

Feet per minute ft/min

Feet per second ft/s

Miles per hour mph

US gallon

US ounce

Cubic inch

US gal.

US oz.

in³

Pound lbs

10

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

This page has been left blank deliberately.

Information on This Document

How to use this document

1

1.5

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 11

2

2.1

2

Safety

Intended use

Safety

2.1

2.2

Intended use

This machine is a mower and is used to mow crops.

The crops designated for the intended use of this machine are stalk and leaf crops growing on the ground.

The machine is designed exclusively for use in agriculture and may only be used when

• all safety installations specified in the operating instructions are present and in safety position;

• all safety information in the operating instructions are known and observed; this goes for

those in the chapter "Basic safety information", refer to page 13 as well as for those

comprised directly in the chapters of the operating instructions.

The machine may be used only by people who satisfy the personnel qualification requirements designated by the machine manufacturer, see

refer to page 13 .

These operating instructions are part of the machine and must therefore be at hand when the machine is in use. The operation of the machine is permitted only after respective instruction and in compliance with these operating instructions.

If the machine is used for applications which are not described in these operating instructions, this may result in serious injuries or death and damage to the machine and other property.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt the proper operation. For this reason, unauthorised modifications shall exclude any liability of the manufacturer for consequential damage.

Intended use also comprises compliance with the terms of operation, maintenance, and repair specified by the manufacturer.

Reasonably foreseeable misuse

Any use beyond the intended use

refer to page 12 is regarded as improper use and is therefore

misuse according to the Machinery Directive. The manufacturer is not liable for damage resulting from this, the user alone bears the risk.

Such misuse is for example:

Processing of crops which are outside the intended use of the machine, refer to page 12

• Transport of people

• Transport of goods

• Exceeding the permitted technical gross weight

• Non-compliance with the safety labels on the machine and safety notes in the operating instructions

• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the information in the operating instructions

• Unauthorised modifications to the machine

• Attachment of unauthorised or unapproved additional equipment

• Use of spare parts which are not KRONE original spare parts

• Stationary operation of the machine

Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper operation. For this reason, unauthorised modifications will exclude any liability of the manufacturer for consequential damage.

12

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

2.3

2.4

2.4.1

2.4.2

Safety

Service life of the machine

Service life of the machine

• The service life of this machine depends on its proper operation and maintenance as well as the operating and harvesting conditions.

• By heeding the instructions and information in these operating instructions, permanent operational readiness and a long service life of the machine can be achieved.

• After each operating season, inspect the entire machine for wear and other damage.

• Replace damaged and worn components before recommissioning the machine.

• Carry out a full technical inspection of the machine after five years of machine operation and make a decision on further machine usage taking the results of this inspection into account.

2

2.3

Basic safety instructions

Non-compliance with the safety instructions and warnings

Non-compliance with the safety instructions and warnings may result in injuries and damage to the environment and property.

Importance of operating instructions

The operating instructions are an important document and a part of the machine. They are intended for the user and contain information relevant to safety.

Only the procedures indicated in the operating instructions are reliable. If the operating instructions are not followed, people may be seriously injured or killed.

„ Before using the machine for the first time, read and follow all the "Basic safety instructions".

„ Before working, also read and observe the respective sections in the operating instructions.

„ Keep the operating instructions easily accessible for the machine user at all times.

„ Keep the operating instructions ready to hand for the user of the machine in the document storage tube,

refer to page 32 .

„ Hand over the operating instructions to subsequent users.

Personnel qualification of the operating personnel

If the machine is not used properly, people may be seriously injured or killed. To avoid accidents, each person who works with the machine must satisfy the following minimum requirements:

• He is physically capable of controlling the machine.

• He can work safely with the machine in accordance with these operating instructions.

• He understands the method of operation of the machine within the scope of his work and can identify and avoid the dangers associated with the work.

• He has read the operating instructions and can implement the information in the operating instructions accordingly.

• He is familiar with driving vehicles safely.

• For road travel he has adequate knowledge of the highway code and has the stipulated driving licence.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 13

2

2.4

2.4.3

Safety

Basic safety instructions

Personnel qualification of the technicians

If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed improperly on the machine, people may be seriously or fatally injured. To avoid accidents, everyone who performs work according to these instructions must meet the following minimum requirements:

• Qualified professional, with relevant training.

• Capable of assembling the (partially) disassembled machine according to the assembly instructions provided by the manufacturer.

• Capable of extending, modifying or repairing the function of the machine according to the relevant instructions provided by the manufacturer.

• Ability to perform the work safely according to these instructions.

• Understands the mode of operation of the work to be performed and the machine and is able to identify and avoid risk in carrying out the necessary work.

• Has read these instructions and is able to implement the information explained in these instructions accordingly.

2.4.4

Children in danger

Children are not in a position to assess dangers and behave unpredictably.

Thus children are particularly at risk.

„ Keep children away from the machine.

„ Keep children away from consumables.

„ Make sure that there are no children in the danger zone, especially when starting and triggering machine movements.

2.4.5

2.4.6

2.4.7

Connecting the machine

When tractor and machine are not correctly connected, there is a risk of causing serious accidents.

„ When connecting, observe all the operating instructions:

• The operating instructions of the tractor

The operating instructions of the machine, refer to page 42

• The operating instructions of universal shaft

„ Observe the changed driving behaviour of the combination.

Structural modifications on the machine

Structural changes and enhancements may impair the functionality and operational safety of the machine. People may be seriously injured or killed as a result.

Structural changes and enhancements are not permitted.

Additional equipment and spare parts

Additional equipment and spare parts that do not correspond to the requirements of the manufacturer may affect the operational safety of the machine and cause accidents.

„ To ensure operational safety, use original parts or standard parts which correspond to the requirements of the manufacturer.

14

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

2.4.8

2.4.9

Safety

Basic safety instructions

2

2.4

Jobs on the machine

Passengers

Passengers can be seriously injured by the machine or fall from the machine and be overrun.

Ejected objects may strike and injure passengers.

„ As a result, make sure that no one except the operator is on the machine.

Operational safety: Technically sound condition

Operation is only allowed after proper start-up

The operational safety of the machine is not ensured when it is not started up properly according to these operating instructions. Thus accidents may be caused and persons may be seriously injured and killed.

„

Only use the machine after proper start-up, refer to page 42 .

Technically sound state of the machine

Improper maintenance and setting could influence the operational safety of the machine and cause accidents. Thus there is a risk of serious injuries or death.

„ All maintenance and setting work must be performed according to the chapters

“Maintenance and Setting”.

„ Before performing any maintenance and setting work, shut down and safeguard the machine,

refer to page 24 .

Danger resulting from damage to the machine

Damage to the machine may impair the operational safety of the machine and cause accidents.

As a result, people may be seriously injured or killed. The following parts of the machine are particularly important for safety:

• Brakes

• Steering

• Safety Devices

• Connecting devices

• Lighting equipment

• Hydraulics

• Tyres

• Universal shaft

If there are doubts about the operational safety of the machine, for example due to an unexpected change to the operational behaviour, visible damage or leaking consumables:

„

Shut down and secure the machine, refer to page 24

.

„ Immediately eliminate potential causes of damage, for example heavy soiling, or tighten slack screws.

„ In case of damage which may affect operational safety and cannot be repaired according to these operating instructions: Have damage repaired by a qualified service centre.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 15

2

2.4

Safety

Basic safety instructions

Technical limit values

If the technical limit values of the machine are not observed, the machine may be damaged. As a result, accidents may occur and people may be seriously injured or killed. Observance of the following technical limit values is particularly important for safety:

• Maximum permissible operating pressure of hydraulics

• Maximum permissible drive speed

• Maximum permissible axle loads of tractor

„

Observe the limits, refer to page 35

.

2.4.10

Danger zones

If the machine is switched on, its surrounding can present a danger zone.

Avoid entering the danger zone of the machine by observing the minimum safety distance.

If the safety distance is not observed, people may be seriously injured or killed.

„ Do not switch on the drives and engine if the minimum safety distance has not been observed.

„ If people fail to observe the minimum safety distance, switch off the drives.

„ Switch the machine off in shunting and field mode.

The safety distance is:

For machine in shunting operation and field mode

In front of the machine 30 m

Behind the machine

Laterally to the machine

5 m

3 m

For machine switched on without driving motion

In front of the machine 3 m

Behind the machine 5 m

Laterally to the machine 3 m

The safety distances specified here are minimum distances in terms of intended use. If necessary, these safety distances must be increased according to the operating and ambient conditions.

„ Before working in front of and behind the tractor and in the danger zone of the machine:

Shut down and secure the machine, refer to page 24

. This also applies to brief inspection work.

„ Consider the information in all relevant operating instructions:

• The operating instructions of the tractor

• The operating instructions of the machine

• The operating instructions of the universal shaft

Danger zone universal shaft

People may become caught by the universal shaft, pulled in and seriously injured.

„ Observe operating instructions of universal shaft.

„ Ensure sufficient overlap of section tube and universal shaft guards.

„ Make sure that the universal shaft guards are mounted and that they are fully functional.

„ Allow the universal shaft locks to engage.

16

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Safety

Basic safety instructions

„ Attach chains to prevent the universal shaft guards from rotating with the shaft.

„ Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

„ Ensure that the selected speed and direction of rotation of the PTO shaft of the tractor match the permitted speed and direction of rotation of the machine.

„ Switch off the PTO shaft when the angles between the universal shaft and the PTO shaft are too large. The machine may be damaged. Parts may be hurled up and cause injury to people.

2

2.4

Danger zone PTO shaft

People may be caught, pulled in and seriously injured by the PTO shaft and driven parts.

Before switching on the PTO shaft:

„ Ensure that all protective devices are mounted and brought into protective position.

„ Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

„ Switch off drives in case they are not needed.

Danger zone between tractor and machine

Persons staying between tractor and machine can be seriously hurt or killed as the tractor may roll away or the machine may move:

„

Before working between tractor and machine: Shut down and safeguard the machine, refer to page 24 . This also applies to short-term control work.

„ If the lifting device must be actuated, instruct all persons to keep away from the range of movement of the lifting device.

Danger zone because objects may shoot out

Crops and foreign bodies may shoot out and injure or kill people.

„ Before starting the machine, instruct all people to leave the danger zone of the machine.

„ If people are in the danger zone of the machine, switch off drives and diesel engine immediately.

Danger zone when drive is switched on

When drive is switched on, there is danger to life caused by moving machine parts. People must not stay in the danger zone of the machine.

„ Before starting the machine, instruct all persons to leave the danger zone of the machine.

„ In case of dangerous situations, immediately switch off drives and instruct persons to leave the danger zone.

Danger zone due to trailing machine parts

If machine parts are trailing, people may be seriously injured or killed.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 17

2

2.4

Safety

Basic safety instructions

After the drives have been switched off, the following machine parts will trail:

• Universal shafts

• Cutting discs

• Conditioner

• Conveying devices

„

Shut down and safeguard the machine, refer to page 24

.

„ Do not approach the machine until all machines parts have come to a complete stop.

2.4.11

Ensuring functionality of safety devices

If safety devices are missing or damaged, moving machine parts could seriously hurt or kill persons.

„ Replace damaged safety devices.

„ Mount dismounted safety devices and machine parts again before start-up and move them to protective position.

„ When there are doubts whether all safety devices are functional and have been correctly installed, instruct a specialist workshop to check this.

2.4.12

Personal protective equipment

The wearing of personal protective equipment is an important safety measure. Missing or unsuitable personal protective equipment increases health risks and injuries.

Personal protective equipment is for example:

• Suitable protective gloves

• Safety boots

• Close fitting protective clothing

• Hearing protection

• Safety glasses

„ Specify and provide personal protective equipment for the particular job.

„ Use only personal protective equipment which is in proper condition and offers effective protection.

„ Adjust personal protective equipment to the person, for example the size.

„ Remove unsuitable clothing and jewellery (e.g. rings, necklaces) and cover long hair with a hairnet.

2.4.13

Safety markings on the machine

Safety labels on the machine caution against dangers at danger areas and represent an important part of the safety equipment of the machine. Missing safety labels increase the risk of serious and fatal injuries.

„ Clean dirty safety labels.

„ Make sure every time after cleaning the safety labels that they are complete and legible.

„ Immediately replace missing, damaged and unrecognizable safety labels.

„ Provide spare parts with intended safety labels.

Descriptions, explanations and order numbers of safety labels, refer to page 25

.

18

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

2.4.14

Safety

Basic safety instructions

2

2.4

Road safety

Dangers for road travel

If the machine exceeds the maximum dimensions and weights specified by national law and is not correctly lit when travelling on public roads, other road users may be endangered.

„ Before driving on roads, ensure that the maximum permitted dimensions, weights and axle, drawbar and trailer loads are not exceeded which apply to driving on public roads according to national law.

„ Before driving on roads, switch on the road travel lighting and ensure that it functions properly.

„ Before driving on roads, close all stop cocks for the hydraulic supply to the machine between tractor and machine.

„ Before driving on roads, move the tractor control units to the neutral position and lock them.

Danger when driving on road and field

Hitched and mounted machines change the handling characteristics of the tractor. The handling characteristics depend for instance on operating state and ground. If changed handling characteristics are not considered, the driver may cause accidents.

„ Observe measures for driving on road and field,

refer to page 54 .

Danger due to machine which is not prepared properly for road travel

If the machine is not prepared properly for road travel, serious accidents may occur on the roads.

„ Before driving on roads, prepare the machine for road travel,

refer to page 55 .

Danger when cornering with mounted machine

When cornering, the tractor with mounted machine has a larger swivelling range. This may result in accidents.

„ Consider the larger swivel range.

„ Consider people, oncoming traffic and obstacles when turning.

Dangers when operating the machine on slopes

The machine may tilt when it is used on slopes. As a result, accidents may occur and people may be seriously injured or killed.

„ Do not work and drive on a slope unless the ground of the slope is flat and the adhesion of the tyres to the ground is ensured.

„ Turn the machine at low speed. Turn in a large arc.

„ Avoid driving across a slope because the centre of gravity of the machine will be changed by payload and by executing machine functions.

„ Avoid abrupt steering movements on slopes.

„ Do not move the machine from working position to transport position or from transport position to working position as long as the machine is used across a slope.

„ Do not park the machine on slopes.

„ Observe procedures for operating the machine on slopes,

refer to page 53 .

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 19

2

2.4

2.4.15

Safety

Basic safety instructions

Parking the machine safely

An improperly parked machine may move uncontrollably or tip over. People may be injured or killed.

„ Park the machine on a horizontal and level ground capable of bearing the load.

„ Before adjusting, repairing, servicing and cleaning the machine, ensure that it is securely positioned.

„ Note section “Parking the Machine” in chapter Driving and Transport,

refer to page 55 .

Unattended parking

Adults and especially children are at risk from an inadequately secured and unattended parked machine.

„ Before parking it: Shut down and safeguard the machine,

refer to page 24 .

2.4.16

Consumables

Unsuitable consumables

Consumables which do not comply with the requirements of the manufacturer may impair the operational safety of the machine and cause accidents.

„ Use only consumables which comply with the requirements of the manufacturer.

For requirements on consumables, refer to page 36 .

Environmental protection and disposal

Consumables such as diesel fuel, brake fluid, antifreeze and lubricants (e.g. gearbox oil, hydraulic oil) may damage the environment and the health of people.

„ Do not release consumables into the environment.

„ Fill consumables in a liquid-tight labelled container and dispose of according to the official regulations.

„ Absorb leaked consumables with an absorbent material, fill them in a liquid-tight labelled container and dispose of according to the official regulations.

2.4.17

Dangers arising from environment

Danger of fire

Flammable materials may accumulate in the machine due to operation or animals, for example rodents or nesting birds.

In case of dry usage conditions, dust, impurities and crop residues may inflame on hot parts and the resulting fire could seriously hurt people or kill them.

„ Check and clean the machine every day before using it for the first time.

„ Check and clean the machine regularly during the working day.

20

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

2.4.18

Safety

Basic safety instructions

2

2.4

Life-threatening electric shock from overhead lines

When folding the mowers in and out, the machine may reach the height of overhead lines. This may cause voltage to flash over to the machine and cause a fatal electric shock or fire.

„ Keep a sufficient distance from electrical overhead lines when folding the mowers in and out.

„ Never fold the mowers in or out near pylons and overhead lines.

„ With mowers folded in, keep a sufficient distance from electrical overhead lines.

„ To avoid a potential electric shock caused by a voltage flashover, never leave or climb into the tractor under overhead lines.

Behaviour in case of voltage flashover of overhead lines

Electroconductive parts of the machine could be subject to high electrical voltage caused by voltage flashover. A voltage drop where major voltage differences are present is created on the ground around the machine in case of voltage flashover. Due to major voltage differences in the ground, you could be killed by electric shocks when you make big steps, lay on the ground or support yourself with your hands.

„ Do not leave the cabin.

„ Do not touch any metal parts.

„ Do not establish any conductive connection to the ground.

„ Warn persons: Do not approach the machine. Electrical voltage on the ground may lead to severe electric shocks.

„ Wait for help from professional rescue teams. The overhead line must be switched off.

If people have to leave the cabin despite the voltage flashover, for example because there is an imminent threat to life due to fire:

„ Avoid simultaneous contact with machine and ground.

„ Jump away from the machine. Jump into a safe standing position. Do not touch the machine from the outside.

„ Move away from the machine with very small steps. In doing so, make sure that your feet are close to one another.

Sources of danger on the machine

Noise may damage your health

The noise development of the machine during operation may cause health damage such as hardness of hearing, deafness or tinnitus. When using the machine at high rotational speed, the noise level also increases.

„ Before the machine is started up for the first time, assess the danger by noise. Depending on the ambient conditions, working hours and the working and operating conditions of the machine, specify and use suitable hearing protection.

„ Specify rules for the use of hearing protection and for the working time.

„ During operation keep windows and doors of cabin closed.

„ Remove hearing protection for road travel.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 21

2

2.4

Safety

Basic safety instructions

Liquids under high pressure

The following liquids are under high pressure:

• Hydraulic oil

Liquids escaping under high pressure may penetrate through the skin and cause severe injuries.

„ Shut down and safeguard the machine and contact qualified specialist workshop upon suspicion of damaged pressure system.

„ Never detect leaks with bare hands. Even a very pin-sized hole may lead to serious injuries.

„ When searching for leaks, use suitable aids, e.g. a piece of cardboard to avoid injuries.

„ Keep body and face away from leaks.

„ Consult a doctor immediately if liquid has penetrated in the body. The liquid must be removed from the body as quickly as possible.

Hot liquids

If hot liquids are drained, people may burn and/or scald themselves.

„ When draining hot consumables, wear personal protective equipment.

„ Before performing any repair, maintenance or cleaning work, allow liquids and machine parts to cool off, if necessary.

Damaged compressor unit

Damaged compressed air hoses of compressor unit may tear off. Hoses that move uncontrollably may hurt people seriously.

„ If it is suspected that the compressor unit is damaged, immediately contact a specialist workshop.

„

Shut down and safeguard the machine, refer to page 24

.

Damaged hydraulic hoses

Damaged hydraulic hoses can tear off, burst or cause oil leaks. As a result, the machine may be damaged and people may be seriously injured.

„

Shut down and safeguard the machine, refer to page 24

.

„ If it is suspected that hydraulic hoses are damaged, immediately contact a service centre,

Checking hydraulic hoses.

Hot surfaces

The following components may become hot during operation and may burn people:

• Transfer gearbox

• Mower gearbox

• Belt gearbox

• Hydraulic system

• Cutter bar

„ Maintain a sufficient distance from hot surfaces.

„ Leave machine parts to cool down and wear protective gloves.

22

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

2.4.19

Safety

Basic safety instructions

Dangers in connection with certain activities: Working on the machine

2

2.4

Only perform work when the machine is at standstill

If the machine is not shut down and safeguarded, parts may move unintentionally or the machine may start moving. Thus there is a risk of serious injuries or death.

„ Before carrying out any repair, maintenance and cleaning work on the machine, shutdown and safeguard it,

refer to page 24 .

Maintenance and repair work

Improper maintenance and repair work endanger operational safety. Thus there is a risk of accidents, serious injuries or death.

„ Only perform work which is described in this operating instructions. Prior to any work, stop

and safeguard the machine, refer to page 24 .

„ All other maintenance and repair work must only be performed by qualified specialist workshop.

Raised machine and machine parts

The raised machine and machine parts may fall or tilt unintentionally. People may be seriously injured or killed, as a result.

„

Do not stay under the raised machine or machine parts which are not safely supported, refer to page 24 .

„ Prior to all work on raised machines or machine parts, lower the machine or machine parts.

„ Before performing any work under raised machines or machine parts, secure the machine or machine parts with rigid safety support or with hydraulic shut-off device or by supporting against lowering.

Danger associated with welding work

Improper welding work will endanger the operational safety of the machine. As a result, accidents may occur and people may be seriously injured or killed.

„ Never perform welding work on the following components:

• Gearboxes

• Components of the hydraulics

• Components of the electronics

• Frame or supporting components

• Running gear

„ Before carrying out welding work on the machine, obtain consent by KRONE customer service and, if required, identify alternatives.

„ Before performing welding work on the machine, park the machine safely and disconnect it from the tractor.

„ Have welding work performed by experienced technicians only.

„ Attach the earthing of the welding device near the welding points.

„ Caution when performing welding work near electric and hydraulic parts, plastic parts and pressure accumulators. The parts may be damaged, endanger people or cause accidents.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 23

2

2.5

2.4.20

Safety

Safety routines

Behaviour in dangerous situations and in case of accidents

Any measures not taken or incorrect measures in dangerous situations can make it difficult or impossible to rescue exposed persons. Due to the impeded conditions of rescue, the chances to help and heal injured people deteriorate.

„ As a matter of principle: Park the machine.

„ Get an overview of the existing danger and identify the reason.

„ Secure the accident site.

„ Save persons from the danger zone.

„ Leave danger zone and do not enter it again.

„ Alarm rescue workers and seek help, if possible.

„ Carry out immediate lifesaving actions.

Safety routines 2.5

2.5.1

2.5.2

Shutting down and safeguarding the machine

WARNING

Risk of injury due to movement of the machine or machine parts

If the machine has not been shut down, machine or machine parts may move unintentionally.

As a result, people may be seriously injured or killed.

„ Before leaving the operating position: Shut down and safeguard the machine.

To shut down and safeguard the machine:

„ Park the machine on a stable, horizontal and level ground.

„ Switch off the drives and wait until coasting parts have come to a complete stop.

„ Lower machine completely to the ground.

„ Switch off tractor engine, remove the ignition key and carry it with you.

„ Secure the tractor against rolling away.

Securing raised machine and machine parts against lowering

WARNING

Crushing hazard due to movement of machine or machine parts

If the machine or machine parts are not secured against lowering, the machine or machine parts may roll, fall or sag. Thus people could be squeezed or killed.

„ Lower the raised machine parts.

„ Shut down and safeguard the machine,

refer to page 24 .

„ Before working on or under raised machine parts: Secure machine or machine parts against lowering by means of hydraulic shut-off device (e.g. stop cock) on machine side.

„ Before working on or under raised machine parts: Safely support machine or machine parts.

24

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

2.5.3

2.6

Safety

Safety Labels on the Machine

In order to safely support the machine or machine parts:

„ To support, only use suitable and sufficiently dimensioned materials that do not break or yield.

„ Bricks and hollow blocks are not suitable for safely supporting the machine and machine parts. Therefore they must not be used.

„ Car jacks are also not suitable for safely supporting the machine and machine parts. They must not be used, as well.

2

2.6

Carrying out oil level check and oil and filter element changes safely

WARNING

Carrying out oil level check and oil and filter element changes safely

If oil level check and oil and filter element changes are not carried out safely, the operational safety of the machine may be impaired. This may result in accidents.

„ Carry out oil level check and oil and filter element changes safely.

To carry out oil level check, oil and filter element changes safely:

„ Lower raised machine parts or secure them against falling,

refer to page 24 .

„

Shut down and safeguard the machine, refer to page 24 .

„ Observe the intervals for oil level check, oil and filter element changes,

refer to page 66 .

„ Use only the oil grades and quantities specified in the consumables table,

refer to page 36 .

„ Clean the area around the parts (for example gearbox, high-pressure filter) and make sure that no foreign objects get into the parts or the hydraulic system.

„ Check existing seal rings for damage and replace them, if necessary.

„ Collect leaking or waste oil in a container designated for the purpose and dispose of it

properly, refer to page 20

.

Safety Labels on the Machine

Every safety label is provided with an order number and can be ordered directly from the authorised KRONE dealer. Immediately replace missing, damaged and unrecognisable safety labels.

When attaching safety labels, the contact surface on the machine must be clean and free of dirt, oil and grease to ensure optimum adhesion of the labels.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 25

2

2.6

Safety

Safety Labels on the Machine

Position and meaning of safety labels

26

KM000-134

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

1.

Order No. 27 004 599 0 (1x)

2.

Order No. 27 004 598 1 (1x)

3.

Order No. 27 002 054 0 (1x)

4.

Order No. 27 004 017 0 (2x)

Safety

Safety Labels on the Machine

2

2.6

CAUTION!

Max. PTO speed 1000 RPM

CAUTION!

The operating pressure of the hydraulic system must not exceed 200 bar.

CAUTION

To avoid serious injury or death.

• Read and understand operator´s manual before operating equipment.

• Lower implement, stop tractor engine and remove key before leaving operator´s platform.

• Keep all shields and guards in place.

• Keep hands, feet and clothing away from moving parts.

• Keep riders off the machine.

• Make certain everyone is clear of the machine before starting tractor engine and starting.

• Do not allow unqualified operator to run equipment.

• Do not operate equipment in transport position.

• Never lubricate, adjust, unclog or service the equipment with tractor engine is running.

• Wait for all movement to stop before opening shield or servicing machine.

• Never work underneath equipment without securely supporting.

WARNING!

Hydraulic accumulators store energy.

To AVOID explosion, depressurize the system on the fluid side before repairing.

Failure to comply could result in death or serious injury.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 27

2

2.6

Safety

Safety Labels on the Machine

5.

Order No. 27 002 055 0 (8x)

28

6.

7.

8.

Ord. no. 27 002 056 0 (8x)

Ord. no. 27 002 059 0 (2x)

Ord. no. 27 002 060 0 (2x)

9.

Order No. 27 002 057 0 (4x)

10. Ord. no. 27 002 058 0 (6x)

DANGER

Thrown objects can cause serious injury or death.

• Stay clear of machine while in operation.

• Keep discharge chute and shields in place.

• Replace worn or damaged protective skirting.

DANGER

Blade can cause serious injury or death.

• Stay clear of machine while in operation.

• Keep discharge chute and shields in place.

CAUTION

• High pressure oil leaks can penetrate skin causing serious injury and gangrene. (See operators manual & consult a physican immediately.)

• Do not use finger or skin to check leaks.

• Lower load, release pressure an be sure oil cool before loosening fitting.

WARNING

To avoid Possible injury.

Do not stand between tractor and machine or near machine while changing from transport position or to transport position.To avoid Possible injury.

WARNING

To avoid personal injury.

Never put your hand into the danger area as parts may be moving.

WARNING

Cutting blade continue to rotate after PTO has been disengaged.

To avoid personal injury.

Look & listen for rotation to stop. Do not open cover until all components have stopped.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

11. Order No. 949 228 0 (3x)

12. Order No. 942 229 0 (3x)

Safety

Safety Labels on the Machine

2

2.6

DANGER

ROTATING DRIVELINE – CONTACT CAN

CAUSE DEATH KEEP AWAY!

DO NOT OPERATE WITHOUT-

• All driveline guards, tractor and equipment shields in place.

• Driveline securely attached at both ends.

• -Driveline guards that turn freely on driveline.

DANGER

ROTATING DRIVELINE – CONTACT CAN

CAUSE DEATH KEEP AWAY!

• Shield missing, do not operate

13. Ord. no. 27 009 069 0 (1x)

DANGER

To avoid injury or death, do not contact electric lines.

14. Order No. 27 021 593 0 (1x)

WARNING

Keep tractor hydraulic controls locked during road transport to prevent implement movement and possible personal injury.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 29

2

2.7

2.7

Safety

Safety equipment

Safety equipment

1

2

3

2

3

KMG000-088

Pos.

1

Designation

Stop cocks

Support jacks

Road travel lighting

4 Overload protection

4 4

Explanation

• When transporting the machine and when working under the machine, always close the stop cocks.

• The support jacks are designed for the stability of the machine when it is not connected to the

tractor, refer to page 50 .

• The road travel lighting is used for road safety.

• Before driving on roads, switch on the road travel lighting and ensure that it functions properly.

• The overload protection protects the tractor and the machine from load peaks

„ To avoid damaging the machine, switch off the

PTO shaft if the overload clutch engages continuously.

30

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Safety

Safety equipment

2

2.7

2.7.1

SMV emblem

KM000-567

The SMV emblem (Slow-Moving Vehicle) (1) is attached to slow-moving machines or vehicles travelling on public highways at a speed of less than 40 km/h (25 mph).

The SMV emblem (1) is at the rear in the centre or at the rear on left.

When driving the machine on public highways, the SMV emblem must be mounted.

If the machine is transported on transport vehicles (for example lorry or train), the SMV emblem must be covered or dismounted.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 31

3

3.1

3

Machine description

Machine overview

Machine description

3.1

Machine overview

32

KMG000-044

6

7

4

5

8

9

1

2

3

Outrigger

Lateral suspension arms

Relief spring

Three-point hitch

Support jack

Impact damage protection system

Universally-jointed drive shaft

Spare blade drawer

Main gearbox

10 Cutterbar

11 Mower gearbox

12 Intermediate universal shaft

13 Friction clutch

14 Swath flap

15 Conditioner roller

Tine rotor

16 Side guard

17 Document storage tube

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

3.2

Machine description

Labelling

Labelling

INFORMATION

The entire identification plate represents a legal document and should not be altered or rendered illegible!

3

3.2

3.3

KMG000-021

The machine data are specified on the type plate (1). The type plate is mounted on left at rear on the three-point hitch.

Information for enquiries and orders

If you have any further queries on the machine or if you want to order spare parts, always enter type designation, vehicle identification number and year of manufacture of the corresponding machine. To ensure that these data are always available, we recommend to enter them in the fields on the front cover page of these operating instructions.

Lighting

3.4

KMG000-031

To comply with the Road Traffic Licensing Regulations, the machine is equipped as standard:

• With three-chamber lamps (1) (flashing light, rear light and brake light),

• with white reflectors (2),

• with yellow reflectors (3).

Intermediate universal shaft

To ensure the functionality and to increase the lifetime, the friction clutch must be vented once a year before the beginning of the season,

refer to page 71 .

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 33

3

3.5

Machine description

Pole protection mechanism

3.5

KMG000-014

The intermediate universal shafts (1) for the mower drives are connected with the friction clutches (2) towards the input gearbox. The supporting chains (3) are fastened onto the threepoint hitch (4). The friction clutch protects the tractor and the machine from damage.

Pole protection mechanism

WARNING

Risk of accident due to changed driving behaviour

If the value for the spring on the impact damage protection system is changed, the trigger moment of the impact damage protection system also changes. As a result, the impact damage protection system may trigger in the transport position in case of abrupt loads and the driving behaviour may change. This can lead to accidents.

„ Never change the value for the spring on the impact damage protection system.

34

KMG000-032

The disc mower is equipped with a so-called impact damage protection system in order to protect it from damage when driving onto obstacles. After the impact damage protection system is triggered, the mower swivels back. The impact damage protection system engages again as soon as the mower is moved back.

The trigger moment is factory preset.

Dimension X =85 mm

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

4

Technical data 4

Technical data

Dimensions

Working width

Transport width

Width conditioning system

Parking height

Transport height

Acreage output

Dead weight

9,450 mm

3,000 mm

3,000 mm

4,000 mm

4,000 mm

8-14 ha/h

2,988 kg

Cutting height

Series version

High-cut skid version

Combi skid version

Setting range approx. 1-7 cm approx. 6-12 cm approx. 4-10 cm

Minimum tractor requirements

Power requirement 145 kW (200 HP)

PTO speed 1,000 min ⁻ ¹

Max. operating pressure of hydraulic system 200 bar

Voltage lighting 12 V, 7-pin

Electrical connections

Lighting

Power supply of the machine

Required hydraulic connections

Double-acting hydraulic connection

Machine equipment (series)

Lower link hitch

SafeCut

Blade quick fastener or blade screw connection

Number of cutting discs

Number of mower drums

Conditioning system

Manual gearbox for conditioner

Mechanical spring relief

Ambient temperature

Temperature range for machine operation

Airborne noise emission

Equivalent continuous sound pressure level

12 V, 7-pin socket

12 V, 3-pin socket

1x

Cat. II and cat. III

Series

Series

10 units

4 units

V-shaped steel tines

600/900 min ⁻ ¹

80 mm

-5 to +45°C

>85 dB(A)

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 35

4

4.1

4.1

Technical data

Consumables

Consumables

NOTICE

Complying with change intervals for biooils

To ensure high life expectancy of the machine, it is absolutely necessary to comply with change intervals for biooils due to the ageing of the oils.

NOTICE

Mixing types of oil

If types of oil are mixed, the machine could be damaged.

„ Never mix different types of oil.

„ Before changing the type of oil, consult customer service. Never use engine oil.

Bio-degradable lubricants on request

4.1.1

4.1.2

Oils

Designation

Input gearbox

Main gearbox

Cutterbar

Filling quantity

2.0 l

6.5 l each

7.0 l each

Specification

SAE 90

SAE 90

SAE 90

Initial filling ex works

Wiolin ML 4 SAE 90

Wiolin ML 4 SAE 90

Wiolin ML 4 SAE 90

The filling quantities of the gearboxes are guide values. The correct values result from oil

change/oil level check, refer to page 74

.

Lubricating greases

Designation

Manual lubrication points

Filling quantity

As required 1

Specification

Lubricating grease to DIN

51818 of NLGI class 2, Li soap with EP additives

1 Lubricate the manual lubrication point until grease escapes at the bearing position. After lubricating, remove the grease escaping from the bearing position.

36

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

5

5.1

Control and Display Elements

Operation panel

5

5.1

Control and Display Elements

Operation panel

The operation panel is used to preselect different functions of the machine. The actual functions are executed via the control units of the tractor. The following table explains the function of the individual switches.

KMG000-001

Designation

1 Red warning light

2 Toggle switch

Function

Is lit when the operation panel is switched on.

Middle Operation panel OFF (warning light (1) OFF)

Top Double-acting control unit (2+/2-)

(2-)

Lowers both mowers from transport position to headland position.

(2+)

Raises both mowers from headland position to transport position.

Bottom Activates the lower toggle switch (3).

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 37

5

5.1

Control and Display Elements

Operation panel

Designation

3 Toggle switch

(is only active when the toggle switch (2) is pointing down)

Function

Left Double-acting control unit (2+/2-):

(2-)

Lowers the right mower from headland position to working position.

(2+)

Raises the right mower from working position to headland position.

Double-acting control unit (1+/1-):

(1-)

Lowers the left mower from headland position to working position.

(1+)

Raises the left mower from working position to headland position.

Middle Double-acting control unit (2+/2-):

(2-)

Lowers both mowers from headland position to working position.

(2+)

Raises both mowers from working position to headland position.

38

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

6

6.1

Initial operation

Checklist for initial operation

6

6.1

Initial operation

WARNING

Risk of injury or damage to the machine due to faulty initial operation

If the initial operation is carried out incorrectly or incompletely, the machine may present defects. As a result, people may be injured or killed or the machine may be damaged.

„ Initial operation must only be carried out by authorised technicians.

„ Read in full and observe the “Personnel qualification of technicians”,

refer to page 14

.

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

Checklist for initial operation

ü The machine is mounted according to assembly instructions of the machine.

ü All the screws and nuts have been checked to make certain they are tight and tightened to the specified tightening torques,

refer to page 68 .

ü The safety devices are mounted and checked for completeness and damage.

ü The machine has been fully lubricated,

refer to page 91 .

ü

The oil level has been checked for all gearboxes, refer to page 74

.

ü The hydraulic system has been checked for leaks.

ü The tractor corresponds to the machine requirements,

refer to page 35 .

ü

The axle loads, the minimum counterweight and the total weight have been checked. refer to page 35 .

ü The universal shaft length has been checked and adjusted,

refer to page 41 .

ü

The blades have been inserted, refer to page 79

.

ü The hydraulic system has been vented.

ü The friction clutch has been vented,

refer to page 71 .

ü The coupling points have been adapted,

refer to page 40 .

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 39

6

6.2

6.2

Initial operation

Adapting Coupling Points

Adapting Coupling Points

KM000-106

Lower link pins

The three-point linkage is designed for category II and III.

Conversion to category II

„ Loosen the linch pins (4) and pull out the lower link pins (1).

„ Move the ball sleeve category II (2) to the position (I) and insert the lower link pins (1).

„ Secure the lower link pins (1) with the linch pin (4) and the safety chain (5).

Conversion to category III

„ Loosen the linch pins (4) and pull out the lower link pins (1).

„ Move the ball sleeve category III (3) to the position (II) and insert the lower link pins (1).

„ Secure the lower link pins (1) with the linch pin (4) and the safety chain (5).

Top link pin

The top link pin (1) is designed for category II and III.

40

KM000-107

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

6.3

Initial operation

Adapting universal shaft

Category II (cat. II)

„ Loosen the linch pin (3) and pull out the top link pin (1).

„ Insert the top link pin (1) in the position (I) or (II) and through the ball sleeve cat. II (2).

The thicker journal of the top link pin (1) is facing outwards.

„ Secure the top link pin with the linch pin (3).

„ Make sure that the anti-twist lock (4) of the top link pin is in the recess.

6

6.3

Category III (cat. III)

„ Insert the top link pin (1) in the position (I) or (II) and through the ball sleeve cat. III (2).

The thinner journal of the top link pin (1) is facing outwards.

„ Secure the top link pin with the linch pin (3).

„ Make sure that the anti-twist lock (4) of the top link pin is in the recess.

Adapting universal shaft

KMG000-047

ü The machine is connected to the tractor,

refer to page 42 .

„ Raise machine until the PTO shaft end of the tractor and the drive shaft of the machine are on the same height.

„ Lower machine into working position.

„

Shut down and safeguard the machine, refer to page 24 .

„ Disassemble the universal shaft.

„ Install each half (1, 2) on the tractor and machine side respectively.

„ Shorten section tubes and guard tubes.

NOTICE: Material damage caused by failure to achieve profile overlap! Observe an overlap (shift length) of the profile tubes and guard tubes of at least 200 mm, refer to the operating instructions of the universal shaft manufacturer.

„ Check the overlap of profile tubes and guard tubes.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 41

7

7.1

7

Start-up

Connecting the machine to the tractor

Start-up

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

WARNING

Risk of injury or damage to the machine due to connection lines which have been incorrectly connected, interchanged or improperly installed

If the connection lines of the machine have been incorrectly connected to the tractor or have been improperly installed, they may pull off or be damaged. This may result in serious accidents. If connection lines are interchanged, functions may inadvertently be actuated which may also result in serious accidents.

„ Correctly connect and secure the hoses and cables.

„ Lay the hoses, cables and ropes so that they do not scrape, come under tension or become jammed or come into contact with other components (e.g. tractor tyres).

„ Couple and connect the hoses and cables to the designated connections as described in the operating instructions.

7.1

Connecting the machine to the tractor

NOTICE

The attachment of implements at the front and rear must not cause exceedance of the permissible total weight, of the permissible axle loads and of the carrying capacities of the tractor tyres. Even with a fitted rear-mounted device, the front axle of the tractor must always be loaded with a minimum 20% tare weight of the tractor.

„ Make sure before starting to move that these requirements have been met.

WARNING

Risk of accident by connecting the machine to U-frame coupler

If the machine is not directly connected to three-point hitch of tractor but to U-frame coupler, the machine may tear from the tractor. This may result in serious accidents.

„ Only connect the machine to the three-point hitch of the tractor.

„ Never mount the machine on U-frame coupler.

42

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Start-up

Connecting hydraulic hoses

7

7.2

7.2

KMG000-012

WARNING! People standing between the tractor and the machine may be injured! Make sure that there is no one between the tractor and the machine while the machine is connected to the tractor, especially when reversing the tractor.

„ Move the tractor backward to the machine and position the lower links (1) under the lower link pins of the machine.

„ Raise the lower links (1) until they engage in the ball sleeves and lock.

„ Secure the tractor against rolling away.

„ Hinge the top link (2) on the three-point hitch and secure it.

„ In order to avoid that the machine swivels out laterally when driving on roads and when working on the field, fix the lower links.

Connecting hydraulic hoses

KMG000-076

In order to connect the hydraulic hoses properly, the hydraulic hoses (1, 2) are marked with numbers or letters.

Hydraulic hoses for connection to a single-acting control unit are marked with a number and the plus sign, e.g. (1+).

Hydraulic hoses for connection to a double-acting control unit are marked with the same numbers, plus sign for the pressure line and minus sign for the return, for example (2+/2-).

Use a control unit on the tractor which can be locked in the neutral position against unintentional operation.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 43

7

7.3

Start-up

Connecting operation panel

Control units on the tractor must be used for lifting and lowering the mower and can be locked in the neutral position to prevent unintentional operation.

„ Depressurise the tractor hydraulics.

„

Shut down and safeguard the machine, refer to page 24

.

„ Clean and dry the connections of the quick couplings.

„ Connect the hydraulic hose (1+) to a single-acting control unit of the tractor.

„ Connect the hydraulic hoses (2+/2-) to a double-acting control unit of the tractor.

7.3

Connecting operation panel

NOTICE

Short circuit caused by impurities and moisture in the plug connection

The machine may be damaged by a short circuit.

„ Make sure that the plugs and sockets are clean and dry.

44

KM000-082

ü

The machine is shut down and safeguarded, refer to page 24

.

Connection operation panel to tractor

„ Connect 2-pole plug (2) to 2-pole socket (1) of the tractor.

Connection operation panel to machine

„ Connect the 19-pole plug (3) to the 19-pole socket (4) of the machine.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

7.4

Start-up

Connecting road travel lighting

7

7.4

Connecting road travel lighting

For the version with “road travel lighting”

NOTICE

Short circuit caused by impurities and moisture in the plug connection

The machine may be damaged by a short circuit.

„ Make sure that the plugs and sockets are clean and dry.

7.5

KMG000-013

The road travel lighting is connected by means of the enclosed 7-pin lighting cable (2).

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Connect the 7-pin plug of the lighting cable (2) to the 7-pin socket (1) of the machine.

„ Connect the 7-pin plug of the lighting cable (2) to the 7-pin socket (3) of the tractor.

„ Lay the lighting cable (2) so that it does not touch the tractor wheels.

Installing universal shaft

WARNING

Risk of injury by failure to take account of the danger zone of the universal shaft

If the danger zone of the universal shaft is ignored, persons can be seriously hurt or killed.

„ To avoid accidents, observe the danger zone of the universal shaft,

refer to page 16 .

NOTICE

Changing the tractor

The machine could be damaged if the universal shaft length is not checked when changing the tractor.

„ In order to avoid damage to the machine, check universal shaft length every time the

tractor is changed and correct it, if necessary, refer to page 41

.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 45

7

7.6

Start-up

Checking the tines on the tine conditioner

7.6

KMG000-048

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Slide universal shaft (1) on PTO shaft end of tractor and secure it.

„ Secure universal shaft guard by means of supporting chain (2) against turning.

Checking the tines on the tine conditioner

NOTICE

Loss of tines

Bent and broken tines will cause an imbalance. Therefore the machine may be damaged.

„ Check the tine conditioner for bent and damaged tines each time before it is used.

„ To prevent the loss of tines, check the bearing bolts of the tine bearings and replace them in time.

46

KMG000-017

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Dismount bent and damaged tines (1).

„ Adjust and mount bent tines.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

8

8.1

Operation

Front guard

8

8.1

Operation

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

WARNING

Risk of injury during operation

If the following notes are not observed, persons could be seriously injured or killed.

„ Before you turn on the PTO shaft, make sure that the machine is in working position and that the glide skids touch the ground.

„ Even with intended operation of the machine, there is a danger caused by ejected foreign bodies. Thus instruct all persons to leave the danger zone of the machine.

„ Special care should be taken when working near roads and buildings.

Front guard

WARNING

Risk of injury due to objects being ejected

If the front guard is folded up during work, objects can be ejected. As a result, people may be seriously injured.

„ Fold down the front guard.

„ Connect the guard cloths of the front guard and the side guard using the turnlock fasteners.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 47

8

8.1

8.1.1

Operation

Front guard

Folding up the front guard

8.1.2

KMG000-006

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Open the turnlock fasteners (3).

„ To fold up the front guard (1), press the catch with a screwdriver (2) and fold up the front guard.

Fold down the front guard

KMG000-077

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Fold down the front guard (1).

„ Close the turnlock fasteners (3).

48

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

8.2

8.2.1

Side guard

Folding up side guard (transport position)

Operation

Side guard

8

8.2

8.2.2

KMG000-058

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Open the turnlock fasteners (2).

„ Fold up the side guard (1) until the side guard (1) engages in the latch.

Folding down side guard (working position)

KMG000-027

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Fold down the side guard (1).

„

Ensure that the side guard (1) is secured by the locking, refer to page 61

.

„ Close the turnlock fasteners (2).

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 49

8

8.3

8.3

Operation

Operate the support jack

Operate the support jack

8.3.1

Move parking jacks into transport position

8.3.2

KMG000-015

„ Raise the machine via rear hydraulics so that the support jacks can be swivelled up.

„

Shut down and safeguard the machine, refer to page 24 .

„ Pull the bolt (1), push the front support jack (2) upwards and lock it by means of the bolt (1).

„ Pull the tension bar (4), swivel the rear support jack (3) upwards and lock it by means of the tension bar (4).

Move parking jacks into support position

KMG000-016

„ Raise the machine via rear hydraulics until the support jacks can be swivelled down.

„

Shut down and safeguard the machine, refer to page 24 .

„ Pull the bolt (1), push the front support jack (2) downwards and lock it by using the bolt (1).

„ Pull the tension bar (4), swivel the rear support jack (3) downwards and lock it by using the tension bar (4).

50

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

8.4

Locking / releasing stop cocks

Operation

Locking / releasing stop cocks

8

8.4

8.5

KMG000-089

Close

„ Move the stop cocks (1) into position (I).

Open

„ Move the stop cocks (1) into position (II).

Lowering the machine from transport position to working position

KMG000-045

From transport position to headland position

„ Move the toggle switch (2) to the “ up ” position.

„ Actuate the control unit (2-) until both mowers are lowered to the headland position.

Headland positions

ü The mowers are in the headland position.

„ Move toggle switch (2) to “ bottom ” position.

Lowering both mowers simultaneously from headland position to working position

„ Move toggle switch (3) to “ centre ” position.

„ Actuate control unit (2-) until both mowers are lowered into working position.

„ To mow, move control unit (2-) to float position.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 51

8

8.6

Operation

Mowing

Lifting both mowers simultaneously from working position to headland position

„ Move toggle switch (3) to “ centre ” position.

„ Actuate the control unit (2+) until both mowers are raised into headland position.

Moving right mower from headland position to working position

„ Move toggle switch (3) to “ left ” position.

„ Actuate control unit (2-) until the right mower is lowered into working position.

„ To mow, move control unit (2-) to float position.

Moving right mower from working position to headland position

„ Move toggle switch (3) to “ left ” position.

„ Actuate the control unit (2+) until the right mower is raised into headland position.

Moving left mower from headland position to working position

„ Move toggle switch (3) to “ left ” position.

„ Actuate the control unit (1-) until the left mower is lowered into working position.

„ To mow, move control unit (1-) to float position.

Moving left mower from working position to headland position

„ Move toggle switch (3) to “ left ” position.

„ Actuate the control unit (1+) until the left mower is lifted into headland position.

From headland position to transport position

ü The PTO shaft drive is switched off.

ü The support jacks are swivelled to the transport position and locked by means of the bolts.

„

Move the machine to the headland position, refer to page 51

.

„ Move the toggle switch (2) into the “ upper “ position and hold.

„ Actuate the double-action control unit (2+) until the mowers are raised from the headland position to the transport position.

Note!

To avoid damage to the machine caused by improper operation, switch off the operation panel.

„ To switch off the operation panel, move the toggle switch (2) into the " middle " position.

8.6

Mowing

Preparing to mow

ü All points listed in the chapter "Start-up" have been fulfilled,

refer to page 42

.

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

ü

The front guards are folded down, refer to page 48

.

ü The side guards are folded down,

refer to page 49 .

ü The rear linkage is blocked.

ü The parking jacks are in the transport position,

refer to page 50 .

52

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

8.7

Operation

Field mode on slopes

8

8.7

Mowing

„ Adjust the lateral suspension arms,

refer to page 58

.

„ Before driving into the crops, switch on the tractor PTO shaft at idle and slowly bring it up to the rated speed of the machine.

„ Drive into the crops.

„

Check the ground pressure while mowing, refer to page 60

.

„ To ensure a clean cutting pattern, adjust the driving and cutting speeds to the prevailing conditions (soil condition, state of the crop, height, density).

Driving into an obstacle

„ If the impact damage protection system triggers and the mower is swivelled backwards, reverse the tractor until the impact damage protection system engages automatically.

Mowing small plots

The front mounted mower alone can be used to mow small plots of crops or narrow sections in open fields. In doing so, the lateral mowers must be in the transport position.

INFORMATION

Leave the control units in the float position while mowing.

Field mode on slopes

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may get seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed, Basic safety instructions.

KMG000-094

„ Do not move the machine from transport into working position or from working into transport position as long as the machine is operated diagonal to the slope.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 53

9 Driving and transport

9 Driving and transport

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

WARNING

Risk of accident caused by non-locked regulating valves of tractor

When regulating valves are not locked, machine components could be activated unintentionally. This may result in serious accidents.

„ To avoid that functions are triggered by mistake, the regulating valves of the tractor must be in neutral position when performing transport journeys on the road and must be locked.

WARNING

Risk of accident from open stop cocks

Machine components could be moved unintentionally when stop cocks are open. This may result in serious accidents.

„ In order to avoid that functions are triggered by mistake, the stop cock/s must be closed during transport/road travel.

NOTICE

The attachment of implements at the front and rear must not cause exceedance of the permissible total weight, of the permissible axle loads and of the carrying capacities of the tractor tyres. Even with a fitted rear-mounted device, the front axle of the tractor must always be loaded with a minimum 20% tare weight of the tractor.

„ Make sure before starting to move that these requirements have been met.

54

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

9.1

Prepare the machine for road travel

Driving and transport

Prepare the machine for road travel

9

9.1

9.2

KMG000-041

ü The machine is completely and correctly hitched to the tractor,

refer to page 42 .

ü

The machine is shut down and safeguarded, refer to page 24

.

ü The hydraulic hoses are connected,

refer to page 43 .

ü

The operation panel is connected, refer to page 44 .

ü

The universal shaft is mounted, refer to page 45

.

ü

The front guards are closed and locked, refer to page 48

.

ü

The side guards are folded up, refer to page 49

.

ü The parking jacks are in the transport position,

refer to page 50 .

ü The road lighting has been connected, tested and is functioning properly,

refer to page 45 .

ü The machine is in the transport position,

refer to page 52 .

ü The cylinders are completely retracted.

ü The stop cocks on the hydraulic hoses are closed,

refer to page 51 .

ü The control units on the tractor are in neutral position and locked.

ü

The operation panel is switched off, refer to page 51 .

„ Lower the machine via the rear hydraulics until the maximum transport height reaches or falls below 4 m.

„ Ensure adequate ground clearance.

Switching off the machine

KMG000-019

ü The machine is in the working position or transport position.

„ Depressurise the tractor hydraulics.

„ Raise the machine until the support jacks (5) can be swivelled down.

„ Swivel down the front and rear support jacks (5) and secure them with the bolt (4),

refer to page 50

.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 55

9

9.2

Driving and transport

Switching off the machine

„ Use the tractor hydraulics to lower the machine onto the ground.

„

Shut down and safeguard the machine, refer to page 24

.

„ Remove the universal shaft (6) from the tractor and place it on the storage surface (7).

„ Disconnect the hydraulic hoses (1) from the tractor, attach the dust caps and hang them onto the headstock.

„ Detach the connection of the lighting cables (2) between tractor and machine and place it in the supports provided.

„ Disconnect the power supply (3) between tractor and operation panel.

„ Remove the operation panel from the tractor and place it in the support provided.

„ Detach the top link.

„ Unlock the lower link hooks of the tractor.

„ Continue to lower the rear linkage until the lower link pins are free.

„ Move tractor away carefully.

Parking

KMG000-020

NOTICE

Parking the machine with mowers folded up

To save space, the machine can also be parked with mowers folded up. To prevent the machine from overturning, park it on firm ground.

„ Only park the machine on level ground capable of bearing the load such as concrete or asphalt.

56

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

10

10.1

Settings 10

Setting the cutting height 10.1

Settings

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

Setting the cutting height

KMG000-035

The cutting height is adjusted via the top link (1).

Setting range of cutting height, .

ü The support jack/the support jacks are swivelled down,

refer to page 50

.

ü

The machine is in the working position, refer to page 51

.

„ Lower the machine up to the support jack/(s).

„

Shut down and safeguard the machine, refer to page 24 .

„ Turn the top link until the cutting height is set.

ð Top link longer = greater cutting height

ð Top link shorter = smaller cutting height

„

Swivel the support jack/(s) up, refer to page 50

.

For version with “high-cut skids”

The cutting height can be increased by means of high-cut skids.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 57

10 Settings

10.2

Setting the lateral links

10.2

KMG000-025

ü The machine is in headland position.

ü

The machine is supported safely, refer to page 24

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ The high-cut skids must always be mounted underneath the cutting discs that run next to the mower drums.

„ Insert the high-cut skid (2) into the sliding skid (1) and screw it.

Setting the lateral links

10.3

KMG000-024

For mowing set the height of the three-point hitch until the side links (3) in the front area (1) and in the rear area (2) are at the same height. The setting is made by raising the machine.

„ Raise the machine until the lateral suspension arms (3) are set to X = approx. 0 mm .

Adjusting the relief spring(s)

WARNING

Risk of injury due to incorrectly set relief spring(s)

If the threaded rod of the relief spring is screwed out too far, the compensation spring may tear off and the mower may lower unintentionally. People may be seriously injured or killed as a result.

„ Never unscrew the threaded spindles (2) of the relief springs (1) further than the dimension X = 80 mm.

58

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Settings 10

Adjusting the relief spring(s) 10.3

WARNING

Risk of injury due to adjustment of relief spring(s)

In the working position the relief spring(s) are subject to high drawing tension. In case an attempt is made to remove or adjust the relief spring(s) when the machine is in the working position, people may be seriously injured or killed.

„ The relief spring(s) must only be dismounted or adjusted in the transport position.

„ The bottom fittings on the relief spring(s) are fully screwed in.

NOTICE

Machine damage due to incorrectly set relief spring(s)

If the dimension a is changed, the nuts (3) may come into contact with the rocker arm (4).

This may damage the machine. The dimension a is set in the factory to 3-5 mm.

„ Never change dimension a .

KMG000-039

The relief springs (1) are used to adapt the ground pressure of the cutterbar to the local conditions. In order to protect the sward the load on the cutterbar must be relieved so that it does not jump when mowing, yet does not leave any brush marks on the ground.

Increasing/reducing ground pressure

ü The machine is in the transport position.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Loosen the counter nut (5).

WARNING!

Risk of injury caused by relief spring tearing off.

Never unscrew the threaded spindles (2) of the relief springs (1) further than the dimension X =

80 mm.

„ To increase the ground pressure, increase the dimension X.

„ To reduce the ground pressure, reduce the dimension X.

„ Tighten the counter nut (5).

Set the dimension X in the same way on all relief springs.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 59

10 Settings

10.4

Increasing/reducing ground pressure

10.4

Increasing/reducing ground pressure

10.5

KMG000-039

The relief springs (1) are used to adapt the ground pressure of the cutterbar to the local conditions. In order to protect the sward, the cutterbar must be relieved to such an extent that it does not jump when mowing or leave any traces of abrasion on the ground.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Loosen the counter nut (5).

WARNING! Risk of injury caused by relief spring tearing off!

Never unscrew the threaded spindles (2) of the relief springs (1) further than the dimension X =

80 mm.

„ To increase the ground pressure, increase the dimension X.

„ To reduce the ground pressure, reduce the dimension X.

„ Tighten the counter nut (5).

„ Set the dimension X in the same way on all relief springs.

Setting the side guards

60

KMG000-078

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

10.6

Settings 10

Checking/setting locking of side guards 10.6

The protective equipment can be adapted to harvesting conditions by adjusting the guards. In order to avoid that crop stalks bend because the guards are too low, set the guards higher. To avoid that stones are slung away when the crops are low, set the guards lower.

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

Adjusting the side guard (1)

„ Use a screwdriver (8) to press down the catch and fold up the side guard (1).

„ Loosen the screws (4).

„ Use the console (5) to adjust the height of the side guard (1).

„ Tighten the screws (4).

Adjusting the side guard (2)

„ Fold up the front guard (3),

refer to page 47

.

„ Loosen the screws (6).

„ Use the console (7) to adjust the height of the side guard (2).

„ Tighten the screws (6).

„ Adjust the two side guards identically.

Checking/setting locking of side guards

KMG000-042

The locking (2) prevents during use that the side guard (1) is folded up and foreign bodies are slung away. Therefore make sure every time before using the machine that the side guard (1) of the machine is folded down and secured by the locking (2).

Check the lock

„

Move the machine to the working position, refer to page 51 .

ð If the side guard folds down, it is correctly set.

ð If the side guard does not fold down, the locking must be set.

„ Move the machine to the transport position.

ð If the side guard folds down, the side guard is correctly adjusted.

ð If the side guard does not fold down, the lock must be adjusted.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 61

10 Settings

10.7

Setting the conditioner speed

Setting the locking

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Loosen the screw connection (3).

„ Readjust the locking (2) in the oblong hole.

„ Tighten the screw connection (3).

„ Check the locking (2).

10.7

Setting the conditioner speed

10.8

KMG000-040

Two conditioner speeds can be set on the manual gearbox. This influences conditioning effect and power requirement.

Minimum rotational speed ( ): 600 rpm

Maximum rotational speed ( ): 900 rpm

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Unscrew the wing screw (1) from the actuating lever (2).

„ Turn the actuating lever (2) 180 degrees.

INFO: To turn the actuating lever more easily, turn the mower drum manually.

„ Secure the actuating lever (2) with the wing screw (1).

Setting the degree of conditioning

62

KMG000-066

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

10.9

Settings 10

Setting the swathing 10.9

The degree of conditioning can be changed by adjusting the conditioning sheet using the lever

(1).

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Adjust the lever (1).

Æ In the " + " direction: The distance between the tines and the conditioning sheet is reduced.

The degree of conditioning is increased.

Æ In the " " direction: The distance between the tines and the conditioning sheet is increased.

The degree of conditioning is reduced.

Setting the swathing

KMG000-050

The swath width can be adapted to the crops.

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

ü The widespreading sheet is completely set downwards,

refer to page 64 .

„ Loosen the ring nut (1) on the right-hand and left-hand machine side.

„ Set the swath flaps (2). Perform the same setting on right-hand and left-hand machine side.

ð To the outside (I) = wider swath

ð To the inside (II) = smaller swath

„ Tighten the ring nut (1).

For the version with “additional swath sheet”

The swath width can additionally be set by an extension on the swath flaps.

„ Loosen the palm knobs (1) on right-hand and left-hand machine side.

„ Set the extension (3).

„ Tighten the palm knobs (1) manually.

„ Ensure that the palm knobs are tightened as tight as possible. Otherwise they may be lost due to vibrations.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 63

10 Settings

10.10 Setting wide spreading

10.10

Setting wide spreading

KM000-027

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Swivel the swath flaps (2) completely to the outside (I).

For the version with “deflector sheets”

Depending on the operating conditions, the deflector sheets (3) may have to be readjusted to provide for equal distribution across the entire area.

„ Loosen the palm knobs (1).

„ Shift the deflector sheets (3) to the desired position.

„ Tighten the palm knobs (1) manually.

„ Ensure that the palm knobs are tightened as tight as possible. Otherwise they may be lost due to vibrations.

10.10.1

Setting widespreading sheet

64

KM000-028

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Loosen the palm knobs (1) on right-hand and left-hand machine side.

„ Move the widespreading sheet (2) to the desired position.

In case of swathing, the widespreading sheet must be set completely down.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Settings 10

Setting wide spreading 10.10

In case of wide spreading, adapt the widespreading sheet to the amount of forage.

„ Tighten the palm knobs (1) manually.

„ Ensure that the palm knobs are tightened as tight as possible. Otherwise they may be lost due to vibrations.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 65

11 Maintenance - General Information

11.1

Maintenance table

11 Maintenance - General Information

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

WARNING

Risk of injury caused by test run of the machine

If a test run is performed after repair, maintenance or cleaning work or after technical intervention, the machine may behave unpredictably. Thus there is a risk of serious injuries or death.

ü The machine is in working position.

„ Do not switch on the drives until the mower is resting on the ground and you are absolutely sure that there is no one in the danger zone.

„ The test run of the machine must only be started from the driver's seat.

11.1

11.1.1

Maintenance table

Maintenance - Once after 50 hours

Changing oil

Input gearbox

Main gearbox

refer to page 74

refer to page 75

11.1.2

Maintenance - Before the beginning of the season

Checking oil level

Input gearbox

Main gearbox

Cutterbar

refer to page 74

refer to page 75

refer to page 87

Components

Changing/replacing blades

refer to page 79

Check/replace cutting discs/mower drums

refer to page 85

Check/replace retaining bolt (blade screw connection)

refer to page 82

66

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Maintenance - General Information 11

Maintenance table 11.1

Components

Check/replace retaining bolt (blade quick fastener)

Check/replace blade carrier (blade quick fastener)

Check/replace linings on cutterbar

Vent friction clutch

Tighten screws/nuts

Check/replace locking of side panel

Check guard cloths

11.1.4

Maintenance - Every 50 hours

Components

Tighten screws/nuts on the machine

refer to page 82

refer to page 83

refer to page 86

refer to page 71

refer to page 68

refer to page 61

refer to page 72

11.1.3

Maintenance - Every 10 hours, but at least once a day

Checking oil level

Input gearbox

Main gearbox

Cutterbar

refer to page 74

refer to page 75

refer to page 87

Components

Changing/replacing blades

Check/replace cutting discs/mower drums

refer to page 79

refer to page 85

Check/replace retaining bolt (blade screw connection)

refer to page 82 refer to page 82

Check/replace retaining bolt (blade quick fastener)

Check/replace blade carrier (blade quick fastener)

refer to page 83

Check guard cloths

Check/replace locking of side panel

refer to page 72

refer to page 61

refer to page 68

11.1.5

Maintenance - Every 200 hours

Changing oil

Input gearbox

Main gearbox

11.1.6

Maintenance - Every 6 years

Components

Have the hydraulic hoses replaced by your

KRONE service partner

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

refer to page 74

refer to page 75

67

11 Maintenance - General Information

11.2

Tightening torques

11.2

Tightening torques

Metric thread screws with control thread

INFORMATION

The table does not apply to countersunk screws with hexagon socket in case the countersunk screw is tightened via hexagon socket.

M16

M20

M22

M24

M27

M30

M4

M5

M6

M8

M10

M12

M14

DV000-001

X Thread size

X Strength class

5.6

8.8

Tightening torque (Nm)

3.0

5.9

10

29

42

25

49

85

135

210

425

571

730

1,100

1,450

1 Strength class on screw head

10.9

310

610

832

1,050

1,550

2,100

4.4

8.7

15

36

72

125

200

12.9

365

710

972

1,220

1,800

2,450

5.1

10

18

43

84

145

235

68

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Metric thread screws with fine thread

Maintenance - General Information 11

Tightening torques 11.2

DV000-001

X Thread size

X

M12 x 1.5

M14 x 1.5

M16 x 1.5

M18 x 1.5

M20 x 1.5

M24 x 2

M27 x 2

M30 x 1.5

Strength class

5.6

8.8

Tightening torque (Nm)

88

145

222

368

465

787

1,148

800

1 Strength class on screw head

10.9

130

213

327

525

662

1,121

1,635

2,100

12.9

152

249

382

614

775

1,312

1,914

2,650

Metric thread screws with countersunk head and hexagon socket

INFORMATION

The table applies only to countersunk screws with hexagon socket and metric thread tightened via hexagon socket.

DV000-000

X Thread size

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

1 Strength class on screw head

69

11 Maintenance - General Information

11.2

Tightening torques

X

M4

M5

M6

M8

M10

M12

M14

M16

M20

Strength class

5.6

8.8

Tightening torque (Nm)

2.5

4.7

8

23

34

20

39

68

108

168

340

70

10.9

3.5

7

12

29

58

100

160

248

488

12.9

4.1

8

15

35

67

116

188

292

568

Locking screws on the gearboxes

INFORMATION

The tightening torques only apply to assembly of locking screws, viewing glasses, ventilation and breather filters and bleed valves in gearboxes with cast housings or aluminium or steel housings. The term “locking screw” includes the drain plug, the inspection screw as well as the ventilation and breather filters.

The table only applies to locking screws with external hexagon together with copper seal ring and for bleed valves made of brass with shaped seal ring.

Thread

M10x1

M12 x 1.5

G1/4“

Locking screw and viewing glass with copper ring* )

Bleed valve made of brass

Ventilation/breather filter made of steel

Steel and cast Aluminium

Ventilation and breather filter made of brass

Steel and cast

Maximum tightening torque (Nm) (±10 %)

Aluminium

8

14

14

M14 x 1.5

M16 x 1.5

45

M18 x 1.5

50

M20 x 1.5

40

45

16

24

30

32

24

30

G1/2“

M22X1.5

M24x1.5

G3/4“

M33x2

G1“

M42x1.5

G1 1/4“

32

35

60

60

80

80

100

100

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

11.3

11.4

Maintenance - General Information 11

Deviating tightening torques 11.3

*) Always replace copper rings

Deviating tightening torques

Screws/nuts

Nut for shear protection (rotary hub)

Bearing housing for cutting disc

Bearing housing for mower drum

Tightening torque

300 Nm

55 Nm

55 Nm

Venting the friction clutch

NOTICE

Interventions in the friction clutch will lead to a loss of guarantee!

Interventions in the friction clutch change the slip torque. Therefore the machine may be damaged considerably.

„ Never intervene in the overload protection.

„ Only use KRONE original spare parts.

The friction clutch protects the tractor and the machine from damage. The friction clutch must be vented before starting up for the first time and once a year. The friction clutch is designed with a permanently adjusted turning torque M

R

. The torque is applied to the housing of the friction clutch (2).

Venting friction clutch (Walterscheid)

KM000-072

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Remove the universal shaft.

„ Tighten the nuts (1) evenly.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Turn the nuts (1) back as far as the thread run-out.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 71

11 Maintenance - General Information

11.5

Checking guard cloths

Venting friction clutch (ByPy)

11.5

KM000-603

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Remove the universal shaft.

„ Loosen the cap nuts (1) uniformly but do not dismount them.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Screw in the cap nuts (1) completely.

Checking guard cloths

72

KMG000-010

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Carry out a visual inspection of the guard cloth (1) to ensure that there are no cracks and damage.

Æ The machine can be used when there are no cracks or damages.

Æ Replace guard cloths in case of cracks or damage.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

12

Maintenance - Hydraulic System 12

Maintenance - Hydraulic System

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

WARNING

Hydraulic hoses are subject to ageing

Hydraulic hoses may wear depending on pressure, heat load and the effect of UV rays.

People can be seriously injured or killed by damaged hydraulic hoses.

The date of manufacture appears on the hydraulic hoses. This way the age can be ascertained quickly.

Replacement of the hydraulic hoses is recommended after a lifetime of six years.

„ Use original spare parts when replacing hoses.

NOTICE

Storing and disposing of oils and used oil filters

If oil and used oil filters are not stored and disposed of properly, the environment may be damaged.

„ Store or dispose of used oil and oil filters according to statutory provisions.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 73

13 Maintenance - Gearbox

13.1

Input gearbox

13 Maintenance - Gearbox

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

13.1

Input gearbox

74

KMG000-005

„ Comply with the safety routine "Safe execution of oil level check, oil and filter element exchange",

refer to page 25 .

INFORMATION

The oil level must be checked and the oil must be changed in working position and with machine in horizontal position.

Check oil level

„ Unscrew the locking screw of the inspection hole (1).

ð If the oil reaches up to the inspection hole (1):

„

Screw on the locking screw of the inspection hole (1), tightening torque refer to page 70 .

ð If the oil does not reach up to the inspection hole (1):

„ Remove the locking screw from the filling hole (3).

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw on the locking screw of the inspection hole (1) and the locking screw of the filling hole (3), tightening torque

refer to page 70 .

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

13.2

Maintenance - Gearbox 13

Main gearbox 13.2

Change oil

ü A suitable container is available for escaping oil.

„ Unscrew the locking screw from the inspection hole (1) and the locking screw from the filling hole (3).

„ Unscrew the oil drain plug (2) and drain the oil.

„

Screw in the oil drain plug (2), tightening torque refer to page 70

.

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque refer to page 70 .

Main gearbox

KMG000-22

„ Observe the safety routine “Safely performing oil level check, oil change and filter element

change”, refer to page 25

.

INFORMATION

The oil level must be checked and the oil must be changed in working position and with machine in horizontal position.

Check oil level

„ Unscrew the locking screw of the inspection hole (1).

ð If the oil reaches up to the inspection hole (1):

„

Screw on the locking screw of the inspection hole (1), tightening torque refer to page 70 .

ð If the oil does not reach up to the inspection hole (1):

„ Remove the locking screw from the filling hole (3).

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw on the locking screw of the inspection hole (1) and the locking screw of the filling hole (3), tightening torque

refer to page 70 .

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 75

13 Maintenance - Gearbox

13.2

Main gearbox

Change oil

ü A suitable container is available for escaping oil.

„ Unscrew the locking screw from the inspection hole (1) and the locking screw from the filling hole (3).

„ Unscrew the oil drain plug (2) and drain the oil.

„

Screw in the oil drain plug (2), tightening torque refer to page 70

.

„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3).

„ Screw the locking screw into the inspection hole (1) and the locking screw into the filling

hole (3), tightening torque refer to page 70 .

76

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

14

14.1

Maintenance - Cutterbar

Rotary hub

A

Maintenance - Cutterbar 14

Rotary hub 14.1

B

KMG000-002

Used abbreviations in this figure:

A = Direction of rotation “A” to the centre

B = Direction of rotation “B” in pairs

RE = eccentric bearing housing (clockwise), without distinctive groove

LE = eccentric bearing housing (rotating anticlockwise), with distinctive groove

For protection against overload of mowers, the rotary hubs (1) are secured with nuts (2) and shear pins (3).

When driving onto obstacles (e.g. stones), the both shear pins in the rotary hub will shear off.

The rotary hub incl. nut turns upward on the pinion shaft.

• The cutting discs or drums which move the crop to the left (LH) in the direction of travel have left-handed thread.

• The cutting discs or drums which transport the crop to the right (RH) in the direction of travel have right-handed thread.

To distinguish between right-hand (clockwise) rotation (RH) and left-hand (anti-clockwise) rotation (LH), the nuts (2) and the pinion shafts (4) for the left-hand rotation (LH) have a distinctive groove (a, b).

• The nuts (2) with left-handed thread (LH) have distinctive grooves (a) on the bevel.

• The pinion shafts (4) with left-handed thread (LH) have a distinctive groove (b) on the face.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 77

14 Maintenance - Cutterbar

14.2

Replacing the shear bolt at the rotary hub

14.2

Replacing the shear bolt at the rotary hub

NOTICE

Wrong installation position

The machine may be damaged if the installation position of the bearing housings is not observed.

„ Clockwise rotating (RH) cutting discs / mower drums always have right-handed pinion shaft and nut (no groove mark on pinion shaft and nut).

„ Anti-clockwise rotating (LH) cutting discs / mower drums always have left-handed pinion shaft and nut (with groove mark on pinion shaft and nut).

78

KM000-049_1

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Dismount the cutting disc or the mower drum at the rotary hub with the defective shear bolt.

„ Remove the retaining ring (7).

„ Unscrew the screws (8).

„ Dismount the nut (2) by using the special key (10) included with delivery.

„ Dismount the hub (1).

„ Remove the damaged shear pins (3).

„ Check the nut and the hub for damage.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

14.3

Maintenance - Cutterbar 14

Check/change blades 14.3

INFO : Replace damaged parts by KRONE original spare parts.

„ Fill the space above the bearing with grease (c).

„ Place the hub on the pinion shaft.

INFO : Observe the position of the shear pins. The slots of the shear pins (3) must be mounted facing each other horizontally , see detail (I).

„ Punch the new shear pins from the outside through the hub (1) and the shaft (4) until the end of the pin reaches the surface of the hub (d).

„ Using the special spanner (10), tighten the nut (2) with a tightening torque of 300 Nm .

„ Fit the screws (8) with detent edged washers.

„ Mount retaining ring (7).

„ Mount the cutting disc (5) or the mower drum (6).

Check/change blades

WARNING

Missing, damaged or incorrectly mounted blades and blade supports

If blades are missing, damaged or incorrectly mounted, dangerous unbalanced rotation may be caused and parts may fly around. People may be seriously injured or killed as a result.

„ Check the blades at least once a day and the retaining bolts every time after changing the blades or after contact with foreign objects.

„ Immediately replace missing, damaged or incorrectly mounted blades and blade supports.

„ To avoid imbalance, always replace missing and damaged blades in kits and never mount unevenly worn blades on a cutting disc/mower drum.

14.3.1

Checking the blade for wear

WARNING

Risk of injury due to low material thickness on the blades

If the material thickness on the blades is too low, the blades may loosen due to high rotating speed. Thus there is a risk of serious injuries or death.

„ Replace the blades at the latest when the wear limit is reached.

ð The wear limit is reached when the borehole of the blade touches the marking (1) on the blade or the dimension X is equal to or less than 13 mm .

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 79

14 Maintenance - Cutterbar

14.3

Check/change blades

14.3.2

KM000-038

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

ü The front guard is folded up,

refer to page 48 .

„ Clean the area around the blades, cutting discs and mower drums.

„ Check wear limit.

ð If the dimension is X>13 mm , the wear limit is not reached.

ð If the dimension is X≤13 mm or the borehole touches the marking (1), the blade must be replaced.

Changing blades for the “blade screw connection” version

80

KM000-044

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

ü The front guard is folded up,

refer to page 48 .

ü The area around the blade, mowing discs and mower drums is cleaned.

„ Remove the damaged or worn blade.

„ Check the fastening parts of the blade,

refer to page 82 . Also replace worn or damaged

mounting parts.

INFO : The blades for anticlockwise rotating and clockwise rotating cutting discs/mower drums are different. When mounting the blades, mind the direction of rotation. The arrow on the blade must correspond to the direction of rotation of the respective cutting disc/mower drum.

„ Insert the new blade (5) between the wear skid (2) and the cutting disc (1).

„ Insert the retaining bolt (3) from below through the wear skid (2), the blade (5) and the cutting disc (1).

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Maintenance - Cutterbar 14

Check/change blades 14.3

INFO : Use the locknut (4) only once.

„ Turn the locknut (4) from above on the retaining bolt (3) and tighten it, tightening torque,

refer to page 68 .

„ Repeat the process for all blades.

„ Fold down the front guard.

INFORMATION

Clockwise rotating blades can be ordered by stating order number 00 139 889 *.

Anticlockwise rotating blades can be ordered by stating order number 00 139 888 *.

14.3.3

Changing blades for the “blade quick fastener” version

KM000-045

ü

The machine is in the working position, refer to page 51

.

ü

The machine is shut down and safeguarded, refer to page 24

.

ü The front guard is folded up,

refer to page 48 .

ü The area around the blade, mowing discs and mower drums is cleaned.

„ To remove the blade (2), slide the blade key (1) between the mowing disc (4) and the blade carrier (3) as far as it will go, press it down with one hand and hold it.

„

Check the fastening parts of the blade (2), refer to page 82

. Also replace worn or damaged mounting parts.

INFO : The blades for anticlockwise rotating and clockwise rotating cutting discs/mower drums are different. When mounting the blades, mind the direction of rotation. The arrow on the blade must match the direction of rotation of the corresponding mowing disc/mower drum.

„ To insert the new blade (2), slide the blade key (1) between the mowing disc (4) and the blade carrier (3) as far as it will go, press it down with one hand and hold it.

„ Guide the blade (2) onto the retaining bolt (5) and in a controlled manner release the force of your hand on the blade key (1).

„ Repeat the process for all blades.

„ Fold down the front guard.

INFORMATION

Clockwise rotating blades can be ordered by stating order number 00 139 889 *.

Anticlockwise rotating blades can be ordered by stating order number 00 139 888 *.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 81

14 Maintenance - Cutterbar

14.4

Checking/replacing retaining bolts

14.4

Checking/replacing retaining bolts

WARNING

Risk of injury due to low material thickness on the retaining bolts

If the material thickness on the retaining bolts is too low, the blades may loosen due to the high rotating speed. As a result, people may be seriously injured or killed.

„ Whenever a blade is changed, check the material thickness of the retaining bolts.

„ When the retaining bolts are damaged or worn, replace them in kits per cutting disc/ mower drum.

„ The retaining bolts must be replaced at the latest when the material thickness at the thinnest point is below 14 mm .

Blade screw connection design Blade quick fastener design

KM000-039 / KM000-040

With “Blade quick fastener” design

82

KM000-079

The material thickness of the retaining bolts and blade carriers is checked by means of gauge

(1) included with delivery. The gauge (1) is located on the special tool (2).

Section (1.1) of the gauge (1) is used to check the material thickness of the retaining bolts.

Section (1.2) of the gauge (1) is used to check the contour of the blade carriers.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Maintenance - Cutterbar 14

Checking/replacing blade carrier 14.5

14.5

KM000-089

„ Remove the blades.

„ Clean the section to be checked.

„ Place the gauge (1) with the section (1.1) against the retaining bolt (2).

„ Rotate the gauge by 90 degrees.

Æ If it is not possible to slide the gauge (1) over the retaining bolt (2) during the rotation, the retaining bolt (2) is OK.

Æ If it is possible to slide the gauge (1) over the retaining bolt (2) during the rotation, the retaining bolt (2) must be replaced immediately.

Checking/replacing blade carrier

"Blade quick fastener" version

WARNING

Risk of injury due to low material thickness and/or worn application seam on the blade carriers

If the material thickness is too low and/or an application seam on the blade carrier is worn, blades may loosen due to the high rotating speed. As a result, people may be seriously injured or killed.

„ The blade carriers must be checked at least once a day or after contact with foreign objects.

„ Whenever a blade is changed, check the material thickness of the blade carriers.

„ The material thickness of the blade carriers must not be less than 3 mm at the weakest point.

„ The blade carriers must be replaced at the latest when the application seam (1) is worn at one point.

„ The blade carriers must only be replaced by KRONE original spare parts.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 83

14 Maintenance - Cutterbar

14.5

Checking/replacing blade carrier

KM000-041

With “Blade quick fastener” design

KM000-079

The material thickness of the retaining bolts and blade carriers is checked by means of gauge

(1) included with delivery. The gauge (1) is located on the special tool (2).

Section (1.1) of the gauge (1) is used to check the material thickness of the retaining bolts.

Section (1.2) of the gauge (1) is used to check the contour of the blade carriers.

84

KM000-090

„ Remove the blades.

„ Clean the area to be checked.

„ Slide the gauge (1) with the section (1.2) as far as it will go over the retaining bolt of the blade carrier (2).

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Maintenance - Cutterbar 14

Checking/replacing cutting discs/mower drums 14.6

14.6

KM000-091

Æ If the contour of the blade carrier (2) protrudes completely beyond the contour of the gauge

(1) in section (IC), the wear limit of the blade carrier (2) is not reached.

Æ If the contour of the blade carrier (2) disappears at any point in section (IIC) behind the contour of the gauge, the wear limit of the blade carrier (2) is reached. The blade carrier (2) must be replaced.

Checking/replacing cutting discs/mower drums

WARNING

Deformed cutting discs/mower drums

If cutting discs/mower drums are deformed, blades may become detached due to high rotating speed. As a result, people may be seriously injured or killed.

„ The cutting discs/mower drums must be checked at least once a day or after contact with foreign objects.

„ If cutting discs/mower drums are deformed, the dimension X=48 mm must not be exceeded.

„ The cutting discs/mower drums must only be replaced by KRONE original spare parts.

KM000-042

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 85

14 Maintenance - Cutterbar

14.7

Checking/replacing linings on cutterbar

14.6.1

Checking the wear limit on cutting discs/mower drums

WARNING

Abrasion on cutting discs/mower drums

Due to abrasion limits on the cutting discs/mower drums, the blades or parts may loosen because of high rotating speed. Thus there is a risk of serious injuries or death.

The wear limit for abrasion limits (2) on the cutting discs/mower drums is reached when the material thickness is less than 3 mm .

„ The cutting discs/mower drums must be replaced at the latest when the material thickness is below the minimum material thickness of 3 mm.

„ The cutting discs/mower drums must only be replaced by KRONE original spare parts.

14.7

KM000-043

Checking/replacing linings on cutterbar

NOTICE

Impact stops are checked irregularly

The impact stops are subject to natural wear and must be inspected daily for wear and replaced if required. If there is no inspection, the machine may be damaged.

„ Adjust the welding current and the welding material to the cutterbar material and to the impact stop. If required, carry out a test weld.

86

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Maintenance - Cutterbar 14

Checking oil level 14.8

KM000-081

„ Open the welding seams of the old lining.

„ Remove lining.

„ Deburr the contact areas.

14.8

KM000-080

„ Fit the new lining (3).

„ Weld short I seams on the upper side of the cutterbar in the sections (1) (each should be approx. 30 mm). INFORMATION: The edges (2) must not be welded.

„ On the bottom of the cutterbar, weld the lining (3) to the cutterbar along the whole length in section (5). INFORMATION: The edges (4) must not be welded.

Checking oil level

INFORMATION

There is no need to change the oil on the cutterbar.

Before checking the oil level on the cutterbar, the cutterbar must be aligned levelly by means of a spirit level.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 87

14 Maintenance - Cutterbar

14.8

Checking oil level

KM000-284

„ Observe the safety routine “Safely performing oil level check, oil change and filter element

change”, refer to page 25

.

„

Shut down and safeguard the machine, refer to page 24 .

Aligning cutterbar in transverse direction (direction of travel)

„ Place the spirit level (1) diagonally on the cutterbar.

„ Align the cutterbar using the spirit level (1) and readjust, if necessary, via cutting height

setting, refer to page 57

.

Aligning the cutterbar in longitudinal direction

„ Place the spirit level (1) on two cutting discs.

„ Align the cutterbar using the spirit level (1); align it horizontally using wedges, if necessary.

Checking oil level

88

KM000-036

„ Release the locking screw of the inspection hole (1).

ð The oil level must reach up to the inspection hole (1).

If the oil reaches the inspection hole (1):

„

Mount the locking screw of the inspection hole (1), refer to page 70

.

If the oil does not reach the inspection hole (1):

„ Top up new oil via the inspection hole (1) up to the inspection hole (1).

„

Mount the locking screw of the inspection hole (1), refer to page 70

.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

This page has been left blank deliberately.

Maintenance - Cutterbar 14

Checking oil level 14.8

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 89

15 Maintenance - Lubrication

15.1

Lubricating universal shaft

15 Maintenance - Lubrication

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

NOTICE

Environmental damage caused by consumables

If consumables are not stored and disposed of properly, they may escape into the environment. As a result, the environment will be damaged, even by small quantities.

„ Store the consumables in suitable containers according to the statutory provisions.

„ Dispose of used consumables according to statutory provisions.

NOTICE

Bearing positions will be damaged

If different lubricating greases are used, the lubricated components may be damaged.

„ Do not use lubricating greases which contain graphite.

„ Do not use different lubricating greases.

15.1

Lubricating universal shaft

90

KMG000-007

Universally-jointed drive shaft Intermediate universal shaft

ü

The machine is shut down and safeguarded, refer to page 24

.

„ Observe operating instructions of the universal shaft manufacturer.

„ Lubricate the universal shaft with multi-purpose grease at the intervals indicated in the figure.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

15.2

Maintenance - Lubrication 15

Lubrication chart - Machine 15.2

Lubrication chart - Machine

The information on maintenance intervals is based on average load of the machine. In case of an increased load and under extreme working conditions, the time periods must be reduced.

The types of lubrication are marked by means of icons in the lubrication chart, refer to table.

Type of lubrication

Grease

Lubricant

Multi-purpose grease

Comment

„ Apply two strokes of lubricating grease from the grease gun per grease nipple.

„ Remove excess lubricating grease at the grease nipple.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 91

15 Maintenance - Lubrication

15.2

Lubrication chart - Machine

KMG000-023

92

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Every 50 operating hours

1) 2)

Maintenance - Lubrication 15

Lubrication chart - Machine 15.2

3)

4)

Every 100 operating hours

5) 6)

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 93

16 Storage

16

94

Storage

WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„ To avoid accidents, the relevant safety instructions must be read and observed,

refer to page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

refer to page 24

.

Placing the machine in storage at the end of the harvest season is the best possible way to preserve the machine.

„ Park the machine in a weatherproof and dry place which is far away from corrosive substances.

„ Clean the machine thoroughly.

Chaff and dirt attract moisture which causes steel parts to start rusting.

NOTICE

Damage to the machine due to water damages with high-pressure cleaner

If the water jet from a high-pressure cleaner is aimed directly at bearings and electrical/ electronic components, these parts can be damaged.

„ Do not aim the water jet from high-pressure cleaner at bearings and electrics/electronic components.

„ Lubricate the machine according to lubrication chart. Do not wipe off any grease that comes out of bearing points as the hardened grease will provide additional protection against moisture.

„ Grease the threads of setting screws and similar items.

„ Relieve the relief springs.

„ Disassemble the universal shaft. Lubricate the inner tubes with grease.

„ Grease the grease nipples on the universal joint of the universal shaft as well as on the

bearing rings of the guard tubes, refer to page 90 .

INFORMATION

Follow the operating instructions of the universal shaft manufacturer.

„ Lubricate the piston rods of all hydraulic cylinders liberally and insert as far as possible.

„ Wet all lever joints and bearing positions which cannot be lubricated with oil.

„ Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection agent.

„ Check all moving components for smooth running. If necessary remove, clean, grease and remount.

„ If parts need to be replaced, use KRONE original spare parts only.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Storage 16

INFORMATION

Write down all repair jobs which must be performed by the next harvest and arrange for them to be done with sufficient lead time. Your KRONE dealer is better able to perform maintenance service and any required repairs outside of harvest season.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 95

17 Waste disposal

17 Waste disposal

After the service life of the machine has expired, the individual components of the machine must be disposed of properly. The currently applicable country-specific waste disposal directives and the concerning valid laws must be observed.

Metal parts

• All metal parts must be brought to a metal recycling centre.

• The parts must be freed from operating fluids and lubricants (gearbox oil, oil from hydraulic system, ...) before being scrapped.

• The operating fluids and lubricants must be brought separately to an environmentally friendly disposal point or recycling centre.

Operating fluids and lubricants

• Operating fluids and lubricants (diesel fuel, coolant, gearbox oil, oil from hydraulic system,

…) must be brought to a disposal point for waste oil.

Synthetic materials

• All synthetic materials must be brought to a recycling centre for synthetic materials.

Rubber

• Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre.

Electronic scrap

• All electronic parts must be brought to a disposal point for electronic scrap.

96

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

18

18.1

Appendix

Circuit diagram

>>>

2

150100881_08_en [ }  98]

Appendix 18

Circuit diagram 18.1

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 97

&LUFXLWGLDJUDP

'LVF0RZHU(DV\&XW

(DV\&XW&9&ROOHFW

GRFXPHQWQR '

(1

YHUVLRQ

$ %

.%

.$

6

0 .$

.%

.

.

.

63/

5<(

5<(

5

5

5<(

5<(

5'5' 3:+

;

6<( 6<(

SRZHUVXSSO\

.<(

$3& $3/

PRZHUVWUDQVSRUW SRVLWLRQKHDGODQG

;

FURVVFRQYH\RUEHOWV FRQWURO

9VXSSO\HOHFWURQLFVVXSSO\

VZLWFKLQJ YROWDJH

$5:+

63/

5:+

;5BF

$:+

*1'VXSSO\HOHFWURQLFVVXSSO\

9VZLWFKLQJYROWDJHVXSSO\

9VZLWFKLQJYROWDJHVXSSO\

VXSSO\H[WHUQDOSRWHQWLRPHWHU

VLJQDOH[WHUQDOSRWHQWLRPHWHU

*1'H[WHUQDOSRWHQWLRPHWHU

9VXSSO\VXSSO\)

*1'VZLWFKLQJYROWDJH

VZLWFKLQJYROWDJH)

9VXSSO\VXSSO\

*1'VXSSO\VXSSO\

9RXWSXW

*1'RXWSXW

*1'RXWSXW

9RXWSXW

$;B

$;B

$;B

$;B

$;B

$;B

;B5'

63/

;B:+

63/

$;B

$;B

$;B

$;B

.:+

.<(

;.

;.

;.

;.

:+

$:+

05'

55'

5<(

;B5'

;5BE

;5BD

5<(

55'

FRQWUROXQLW

$:+

;

;

;

;

; ;

6B<(

;6B

;6B

.<(

..<(

.<(

5

5

..<(

.<(

PRZHUVKHDGODQG SRVLWLRQWUDQVSRUW

...:+

;.%:+

;.%<(

63/

63/

;.$:+

;.$<(

;.%:+

;.%<(

;.$:+

;.$<(

63/

63/

;.%:+

;.%<(

;.$:+

;.$<(

5<(

5

;

;

5<(

5

;

;

5'5' %.%.

;

;%

%.

;

;

;

( (

SRZHUVXSSO\

6<( .<(

PRZHUVWUDQVSRUW SRVLWLRQKHDGODQG

;

;

FURVVFRQYH\RUEHOWV FRQWURO

VZLWFKLQJ YROWDJH

9VXSSO\HOHFWURQLFVVXSSO\

$;B

9RXWSXW

*1'H[WHUQDOSRWHQWLRPHWHU

*1'VXSSO\HOHFWURQLFVVXSSO\

9VZLWFKLQJYROWDJHVXSSO\

9VZLWFKLQJYROWDJHVXSSO\

VXSSO\H[WHUQDOSRWHQWLRPHWHU

VLJQDOH[WHUQDOSRWHQWLRPHWHU

*1'RXWSXW

9VXSSO\VXSSO\)

9VXSSO\VXSSO\

VZLWFKLQJYROWDJH)

;B5'

$;B

$;B

$;B

;B :+

$;B

$;B

;65'

;65'

;65'

;6<(

;6:+

*1'VXSSO\VXSSO\

*1'VZLWFKLQJYROWDJH

*1'RXWSXW

9RXWSXW

$;B

$;B

$;B

$;B

;6:+

;6<(

;5F

%.

FRQWUROXQLW

;5D

;5E

5<(

55'

;5D

;5E

%.

%.

*

)

;

)

*

;

/ /

<(

;.<(

0:+

$:+

05'

55'

5<(

;B5'

IURP\HDURIPDQXIDFWXUH

6B$%<(

;6B$

;

;6B%

;

;

;

0

;

0 ..<(

%.

.

;

.

<( .$

.$<(

5

5 %.

+

;

+ ..<(

.%<(

.$<(

& & .<(

.$:+

.$:+

.%:+

.$:+ ..:+

...:+

PRZHUVKHDGODQG SRVLWLRQWUDQVSRUW

Index 19

19 Index

A

Adapting Coupling Points ................................... 40

Adapting universal shaft ..................................... 41

Additional equipment and spare parts ................ 14

Adjusting the relief spring(s) ............................... 58

Appendix ............................................................ 97

Applicable documents .......................................... 6

B

Basic safety instructions ..................................... 13

Behaviour in case of voltage flashover of overhead

lines .................................................................... 21

Behaviour in dangerous situations and in case of

accidents ............................................................ 24

C

Carrying out oil level check and oil and filter

element changes safely...................................... 25

Change oil .................................................... 75, 76

Changing blades for the “blade quick fastener”

version ................................................................ 81

Changing blades for the “blade screw connection”

version ................................................................ 80

Check/change blades ......................................... 79

Checking guard cloths ........................................ 72

Checking oil level ............................................... 87

Checking the blade for wear............................... 79

Checking the tines on the tine conditioner ......... 46

Checking the wear limit on cutting discs/mower

drums ................................................................. 86

Checking/replacing blade carrier ........................ 83

Checking/replacing cutting discs/mower drums . 85

Checking/replacing linings on cutterbar ............. 86

Checking/replacing retaining bolts ..................... 82

Checking/setting locking of side guards ............. 61

Checklist for initial operation .............................. 39

Children in danger .............................................. 14

Circuit diagram ................................................... 97

Connecting hydraulic hoses ............................... 43

Connecting operation panel ............................... 44

Connecting road travel lighting ........................... 45

Connecting the machine..................................... 14

Connecting the machine to the tractor ............... 42

Consumables ............................................... 20, 36

Contact ................................................................. 2

Contact data of your dealer .................................. 2

Control and Display Elements ............................ 37

Conversion table .................................................. 9

Cross references .................................................. 6

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 109

19 Index

D

Damaged compressor unit ................................. 22

Damaged hydraulic hoses .................................. 22

Danger associated with welding work ................ 23

Danger due to machine which is not prepared

properly for road travel ....................................... 19

Danger of fire...................................................... 20

Danger resulting from damage to the machine .. 15

Danger when cornering with mounted machine . 19

Danger when driving on road and field............... 19

Danger zone because objects may shoot out .... 17

Danger zone between tractor and machine ....... 17

Danger zone due to trailing machine parts......... 17

Danger zone PTO shaft...................................... 17

Danger zone universal shaft............................... 16

Danger zone when drive is switched on ............. 17

Danger zones ..................................................... 16

Dangers arising from environment ..................... 20

Dangers for road travel....................................... 19

Dangers in connection with certain activities:

Working on the machine..................................... 23

Dangers when operating the machine on slopes 19

Deviating tightening torques ............................... 71

Directories and references ................................... 6

Driving and transport .......................................... 54

E

Ensuring functionality of safety devices ............. 18

Environmental protection and disposal .............. 20

F

Field mode on slopes ......................................... 53

Figures ................................................................. 7

Fold down the front guard .................................. 48

Folding down side guard (working position) ....... 49

Folding up side guard (transport position) .......... 49

Folding up the front guard .................................. 48

Front guard ......................................................... 47

H

Headland positions ............................................. 51

Hot liquids........................................................... 22

Hot surfaces ....................................................... 22

How to use this document .................................... 6

I

Icons in figures ..................................................... 7

Icons in the text .................................................... 7

Importance of operating instructions .................. 13

Increasing/reducing ground pressure ........... 59, 60

Information for enquiries and orders .............. 2, 33

Information on direction ........................................ 7

Information on This Document ............................. 6

Initial operation ................................................... 39

Input gearbox ..................................................... 74

Installing universal shaft ..................................... 45

Intended use....................................................... 12

Intermediate universal shaft ............................... 33

J

Jobs on the machine .......................................... 15

L

Labelling ............................................................. 33

Life-threatening electric shock from overhead lines

........................................................................... 21

Lighting ............................................................... 33

Liquids under high pressure ............................... 22

Locking / releasing stop cocks ........................... 51

Locking screws on the gearboxes ...................... 70

Lower link pins.................................................... 40

Lowering the machine from transport position to

working position.................................................. 51

Lubricating greases ............................................ 36

Lubricating universal shaft.................................. 90

Lubrication chart - Machine ................................ 91

110

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

Index 19

M

Machine description ........................................... 32

Machine overview............................................... 32

Main gearbox...................................................... 75

Maintenance - Before the beginning of the season

........................................................................... 66

Maintenance - Cutterbar..................................... 77

Maintenance - Every 10 hours, but at least once a

day...................................................................... 67

Maintenance - Every 200 hours ......................... 67

Maintenance - Every 50 hours ........................... 67

Maintenance - Every 6 years.............................. 67

Maintenance - Gearbox ...................................... 74

Maintenance - General Information .................... 66

Maintenance - Hydraulic System........................ 73

Maintenance - Lubrication .................................. 90

Maintenance - Once after 50 hours .................... 66

Maintenance and repair work ............................. 23

Maintenance table .............................................. 66

Means of representation....................................... 7

Metric thread screws with control thread ............ 68

Metric thread screws with countersunk head and

hexagon socket .................................................. 69

Metric thread screws with fine thread ................. 69

Move parking jacks into support position ........... 50

Move parking jacks into transport position ......... 50

Mowing ............................................................... 52

N

Noise may damage your health.......................... 21

Notes with information and recommendations ..... 9

O

Oils ..................................................................... 36

Only perform work when the machine is at

standstill ............................................................. 23

Operate the support jack .................................... 50

Operation............................................................ 47

Operation is only allowed after proper start-up .. 15

Operation panel .................................................. 37

Operational safety: Technically sound condition 15

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

P

Parking the machine safely ................................ 20

Passengers ........................................................ 15

Personal protective equipment ........................... 18

Personnel qualification of the operating personnel

........................................................................... 13

Personnel qualification of the technicians .......... 14

Pole protection mechanism ................................ 34

Position and meaning of safety labels ................ 26

Prepare the machine for road travel ................... 55

R

Raised machine and machine parts ................... 23

Reasonably foreseeable misuse ........................ 12

Re-ordering .......................................................... 6

Replacing the shear bolt at the rotary hub ......... 78

Road safety ........................................................ 19

Rotary hub .......................................................... 77

111

19 Index

S

Safety ................................................................. 12

Safety equipment ............................................... 30

Safety Labels on the Machine ............................ 25

Safety markings on the machine ........................ 18

Safety routines ................................................... 24

Scope of the document ........................................ 7

Securing raised machine and machine parts

against lowering ................................................. 24

Service life of the machine ................................. 13

Setting the conditioner speed ............................. 62

Setting the cutting height .................................... 57

Setting the degree of conditioning ...................... 62

Setting the lateral links ....................................... 58

Setting the side guards....................................... 60

Setting the swathing ........................................... 63

Setting wide spreading ....................................... 64

Setting widespreading sheet .............................. 64

Settings .............................................................. 57

Shutting down and safeguarding the machine ... 24

Side guard .......................................................... 49

SMV emblem ...................................................... 31

Sources of danger on the machine .................... 21

Start-up............................................................... 42

Storage ............................................................... 94

Structural modifications on the machine ............ 14

Switching off the machine .................................. 55

T

Target group of this document ............................. 6

Technical data .................................................... 35

Technical limit values ......................................... 16

Technically sound state of the machine ............. 15

Term “machine” .................................................... 7

Tightening torques.............................................. 68

Top link pin ......................................................... 40

U

Unattended parking ............................................ 20

Unsuitable consumables .................................... 20

V

Validity .................................................................. 6

Venting the friction clutch ................................... 71

Von Transport- in Vorgewendestellung .............. 51

Von Vorgewende- in Transportstellung .............. 52

Vorgewendestellungen ....................................... 51

W

Warning signs....................................................... 8

Warnings of property damage/environmental

damage ................................................................ 9

Waste disposal ................................................... 96

112

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en

This page has been left blank deliberately.

EasyCut B 870 CV

Original Operating Instructions 150000705_01_en 113

Maschinenfabrik

Bernard Krone GmbH & Co. KG

* Heinrich-Krone-Straße 10

D-48480 Spelle

* Postfach 11 63

D-48478 Spelle

' +49 (0) 59 77 / 935-0

6 +49 (0) 59 77 / 935-339

ü

www.landmaschinen.krone.de

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement

Table of contents