Krone EasyCut F 360 CV, EasyCut F 360 CR, EasyCut F 320 CV Operating Instructions


Add to my manuals
122 Pages

advertisement

Krone EasyCut F 360 CV, EasyCut F 360 CR, EasyCut F 320 CV Operating Instructions | Manualzz

EasyCut F 360 CV

EasyCut F 360 CR

EasyCut F 320 CV

(from serial no.: 915 529)

Order no.: 150 000 173 02 en

Disc Mower

27.04.2016

Table of Contents

Pos: 1 /BA/Konfor mitätser kl ärungen/EasyC ut/Neu ab 2010/EasyC ut F 320 C V/F 360 CV/F 360 CR @ 448\mod_1461566771330_78.docx @ 3049925 @ @ 1

CV0

EC Declaration of Conformity

We

Maschinenfabrik Bernard Krone GmbH & Co. KG

Heinrich-Krone-Str. 10, D-48480 Spelle hereby declare as manufacturer of the product named below, on our sole responsibility, that the

Machine:

Disc Mower

Type:

EasyCutF 320 CV, F 360 CV, EasyCut F 360 CR to which this declaration refers is in compliance with the following relevant provisions of:

• EC Directive 2006/42/CE (machines).

The signing Managing Director is authorised to compile the technical documents.

Spelle, 25.04.2016

Dr.-Ing. Josef Horstmann

(Managing Director, Design & Development)

Year of manufacture:

Pos: 2 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine no.:

2

Pos: 3 /Layout Modul e /Inhaltsverzei chnis @ 0\mod_1196861555655_78.docx @ 15165 @ 1 @ 1

Table of Contents

1 Table of Contents

1 Table of Contents ................................................................................................................................... 3

2 To this Document ................................................................................................................................... 7

2.1

Validity ................................................................................................................................................ 7

2.2

Re-Ordering ........................................................................................................................................ 7

2.3

Further applicable documents ............................................................................................................ 7

2.4

Target group of this document ........................................................................................................... 7

2.5

How to use this document .................................................................................................................. 7

2.5.1

Directories and References ........................................................................................................ 7

2.5.2

Direction Information ................................................................................................................... 8

2.5.3

Term “Machine” ........................................................................................................................... 8

2.5.4

Figures ........................................................................................................................................ 8

2.5.5

Scope of Document ..................................................................................................................... 8

2.5.6

Means of representation ............................................................................................................. 8

3 Safety ..................................................................................................................................................... 11

3.1

Purpose of Use ................................................................................................................................. 11

3.2

Intended use ..................................................................................................................................... 11

3.3

Service life of the machine ............................................................................................................... 11

3.4

Safety Instructions and Accident Prevention Regulations ............................................................... 12

3.4.1

Personnel Qualification and Training ........................................................................................ 13

3.4.2

Dangers in Case of Non-compliance with the Safety Instructions ............................................ 13

3.4.3

Safety-conscious work practices ............................................................................................... 13

3.5

Attached devices .............................................................................................................................. 14

3.6

PTO operation .................................................................................................................................. 14

3.7

Hydraulic system .............................................................................................................................. 15

3.8

Maintenance ..................................................................................................................................... 15

3.9

Unauthorised Conversion/Modification and Spare Parts Production ............................................... 15

3.10

Inadmissible Modes of Operation ..................................................................................................... 15

4 Machine Description ............................................................................................................................ 16

4.1

Machine overview ............................................................................................................................. 16

4.2

Identification Plate ............................................................................................................................ 24

4.3

Information Required for Questions and Orders .............................................................................. 24

4.3.1

Contact ...................................................................................................................................... 24

4.4

Introduction ....................................................................................................................................... 25

4.4.1

Re-Ordering Safety Labels and Information Labels .................................................................. 25

4.4.2

Attaching Safety Labels and Information Labels ...................................................................... 25

4.5

Position of the Adhesive Safety Stickers on the Machine ................................................................ 26

5 Technical Data of the Machine ............................................................................................................ 42

5.1

Technical data .................................................................................................................................. 42

5.2

Consumables ................................................................................................................................... 48

5.3

Ambient Temperature....................................................................................................................... 48

6 Commissioning ..................................................................................................................................... 49

6.1

Special Safety Instructions ............................................................................................................... 49

6.2

First installation ................................................................................................................................ 49

6.3

Adapting to the tractor ...................................................................................................................... 49

6.4

Mounting onto the Tractor ................................................................................................................ 50

6.4.1

Clutching points ......................................................................................................................... 50

3

Table of Contents

6.4.2

Lower suspension arm .............................................................................................................. 51

6.5

PTO shaft ......................................................................................................................................... 52

6.5.1

Length adjustment ..................................................................................................................... 52

6.5.2

Install the PTO shaft .................................................................................................................. 53

7 Start-up .................................................................................................................................................. 54

7.1

Preparations on tractor ..................................................................................................................... 54

7.2

Install the PTO shaft ......................................................................................................................... 55

7.3

Mounting and Adjusting the Relief Springs ...................................................................................... 56

7.3.1

Pushed Design .......................................................................................................................... 56

7.4

Checking Spring Retaining Chain .................................................................................................... 58

7.4.1

Trailed Design ........................................................................................................................... 59

7.5

Tensioning Guard Cloth ................................................................................................................... 59

7.6

Lighting connection .......................................................................................................................... 60

7.7

Hydraulics ......................................................................................................................................... 61

7.7.1

Special Safety Instructions ........................................................................................................ 61

7.7.2

Connecting the hydraulic lines .................................................................................................. 61

7.8

Trial run after first installation ........................................................................................................... 62

7.9

Checking Fitting ................................................................................................................................ 63

8 Driving and Transport .......................................................................................................................... 64

8.1

Lighting ............................................................................................................................................. 64

8.2

Clamp and Buffer ............................................................................................................................. 66

9 Operation ............................................................................................................................................... 68

9.1

Before mowing ................................................................................................................................. 68

9.2

Tensioning Guard Cloth ................................................................................................................... 69

9.3

Moving the guards into the working position .................................................................................... 69

9.4

Moving Guards into Transport Position ............................................................................................ 70

9.5

Parking support ................................................................................................................................ 70

9.6

Detaching the machine..................................................................................................................... 71

9.7

Dismounting Retaining Chains ......................................................................................................... 71

10 Settings ................................................................................................................................................. 72

10.1

Adjusting the Compensation Springs ............................................................................................... 72

10.2

Adjusting the Guards ........................................................................................................................ 73

10.2.1

Pushed Design .......................................................................................................................... 74

10.2.2

Trailed Design ........................................................................................................................... 75

10.3

Adjusting the cutting height .............................................................................................................. 76

10.3.1

Telescopic upper suspension arm ............................................................................................ 76

10.4

Setting Conditioner Speed ............................................................................................................... 77

10.4.1

Changing Pulley ........................................................................................................................ 78

10.4.2

Replacing Pulley ....................................................................................................................... 79

10.4.3

Tensioning Belt Drive ................................................................................................................ 79

10.5

Adjusting the conditioner plate ......................................................................................................... 80

10.5.1

Adjustment for Swathing ........................................................................................................... 80

10.5.2

Wide spreading ......................................................................................................................... 81

10.6

Setting the Distance of the Rollers ................................................................................................... 82

11 Maintenance .......................................................................................................................................... 83

11.1

Special Safety Instructions ............................................................................................................... 83

11.1.1

Test run ..................................................................................................................................... 83

11.2

Spare Parts ...................................................................................................................................... 83

4

Table of Contents

11.3

Maintenance table ............................................................................................................................ 84

11.4

Tightening torques ............................................................................................................................ 85

11.4.1

Metric Thread Screws with Control Thread............................................................................... 85

11.4.2

Metric Thread Screws with Fine Thread ................................................................................... 86

11.4.3

Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 86

11.4.4

Deviating Tightening Torques ................................................................................................... 87

11.5

Intermediate PTO shaft .................................................................................................................... 87

11.6

Rotary hub with shear fuse (optional) .............................................................................................. 88

11.6.1

After Shearing Off ..................................................................................................................... 92

12 Maintenance - Gearbox ........................................................................................................................ 94

12.1

Input gearbox ................................................................................................................................... 94

12.2

Angular gearbox ............................................................................................................................... 95

12.3

Angular gearbox ............................................................................................................................... 96

12.3.1

Top part ..................................................................................................................................... 96

12.4

Angular gearbox ............................................................................................................................... 97

12.4.1

Bottom part ................................................................................................................................ 97

12.5

Gearbox for Top Roller Drive ........................................................................................................... 98

12.6

Tensioning Belt Drive ....................................................................................................................... 99

12.7

Oil level check and oil change on the cutter bar ............................................................................ 100

12.7.1

Oil change ............................................................................................................................... 100

12.7.2

Checking the oil level .............................................................................................................. 100

12.7.3

Aligning the Cutter Bar ............................................................................................................ 100

13 Maintenance - Blade Changing ......................................................................................................... 102

13.1

Checking the Cutter Blades and Blade Holder .............................................................................. 102

13.1.1

Cutter Blades .......................................................................................................................... 103

13.1.2

Blade screw connection .......................................................................................................... 104

13.1.3

Blade Quick-Fit Device............................................................................................................ 105

13.1.4

Periodical Inspection of the Leaf Springs................................................................................ 106

13.1.5

Periodical Inspection of the Cutting Discs / Blade Drums ....................................................... 107

13.1.6

Abrasion Limit ......................................................................................................................... 108

13.2

Blade Changing on Cutting Discs .................................................................................................. 109

13.2.1

Blade Screw Connection ......................................................................................................... 110

13.2.2

Blade Quick-Fit Device............................................................................................................ 111

13.3

Replacing the linings ...................................................................................................................... 112

14 Maintenance – lubrication chart ....................................................................................................... 113

14.1

Special Safety Instructions ............................................................................................................. 113

14.2

Universally-Jointed Drive Shaft ...................................................................................................... 113

14.3

Intermediate PTO shaft .................................................................................................................. 114

14.4

Lubrication Chart ............................................................................................................................ 114

15 Placing in Storage .............................................................................................................................. 115

16 Before the Start of the New Season ................................................................................................. 116

16.1

Special Safety Instructions ............................................................................................................. 116

16.2

Test run. ......................................................................................................................................... 116

16.3

Friction Clutch ................................................................................................................................ 117

17 Special equipment .............................................................................................................................. 118

17.1

Special Safety Instructions ............................................................................................................. 118

17.2

Adjusting Skids ............................................................................................................................... 118

18 Disposal of the machine .................................................................................................................... 119

5

Table of Contents

18.1

Disposal of the machine ................................................................................................................. 119

19 Index .................................................................................................................................................... 120

Pos: 4 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

6

Pos: 5 /Ü berschriften/Ü berschriften 1/U-Z/Z u diesem D okument @ 107\mod_1334231929021_78.docx @ 965257 @ 1 @ 1

To this Document

2 To this Document

Pos: 6 /BA/Ei nleitung/Gültig keit/EasyC ut /Gültig kei t EasyC ut F 320 C V / EasyC ut F 360 C V / EasyC ut F 360 CR @ 321 \mod_1424786573834_78.docx @ 2479606 @ 2 @ 1

2.1 Validity

These operating instructions are valid for disc mowers of series

:

EasyCut F 320 CV, EasyCut F 360 CV, EasyCut F 360 CR

Pos: 7.1 /Ü berschriften/Ü berschriften 2/K- O/N/N achbestell ung (N achbestellung di eses D okuments) @ 349\mod_1436355974813_78.docx @ 2625865 @ 2 @ 1

2.2 Re-Ordering

Pos: 7.2 /BA/Zu di esem D okument/N achbestellung_T ext @ 349\mod_1436355830140_78.docx @ 2625835 @ @ 1

Pos: 8 /Ü berschriften/Ü berschriften 2/K-O/M/Mitg eltende Dokumente @ 187\mod_1380113031071_78.docx @ 1609664 @ 2 @ 1

If this document should become wholly or partially unusable, you can request a replacement document by stating the order number mentioned on the cover sheet.

2.3 Further applicable documents

Pos: 9 /BA/Zu di esem D okument/Mitg eltende Dokumente_Ei nführ ungssatz_alle Maschi nen @ 187\mod_1380113940483_78.docx @ 1609940 @ @ 1

To ensure that the machine is used safely and as intended, observe the following further applicable documents:

Pos: 10 /BA/Z u diesem Dokument/Mitgeltende D okumente_Betriebsanl eitung(en) Gel enkwelle( n) @ 347\mod_1435588572591_78.docx @ 2616249 @ @ 1

– Operating instructions of universal shaft(s)

Pos: 11 /Ü berschriften/Überschriften 2/U-Z/Z/Zi elgruppe dieses D okuments @ 187\mod_1380113123454_78.docx @ 1609723 @ 2 @ 1

2.4 Target group of this document

Pos: 12 /BA/Z u diesem Dokument/Zielgruppe @ 345\mod_1434348246902_78.docx @ 2606935 @ @ 1

This document aims at the operators of the machine fulfilling the minimum requirements of personnel qualification; refer to chapter entitled Safety “Personnel Qualification”.

Pos: 14.1 /Überschriften/Überschriften 2/P-T/SSo benutzen Sie dieses Dokument @ 188\mod_1380548350021_78.docx @ 1614365 @ 2 @ 1

2.5 How to use this document

Pos: 14.2 /Überschriften/Überschriften 3/U-Z/Verzeichnisse und Ver weise @ 336\mod_1429854437094_78.docx @ 2556421 @ 3 @ 1

2.5.1 Directories and References

Pos: 14.3 /BA/Z u diesem Dokument/So benutzen Si e dieses Dokument_Verzeichnisse und Ver weise_Text @ 333\mod_1429085378408_78.docx @ 2544425 @ @ 1

Pos: 14.4 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Table of contents/headers:

The table of contents as well as the headers in this instruction are used for quick navigation in the chapters.

Index directory:

In the index directory, you can find information on the desired subject via catchwords which are in alphabetical order. The index directory can be found on the last page of this instruction.

Cross references:

Cross references to another place in the operating instructions or to another document are in the text and specify the chapter and subchapter or section. The designation of subchapters or sections is presented in quotation marks.

Example:

Check that all screws on the machine are tight, refer to chapter Maintenance, “Tightening

Torques”.

The subchapter or the section can be found via an entry in the table of contents and in the index directory.

7

To this Document

Pos: 14.5 /BA/Z u diesem Dokument/Richtungsangaben_mit Ü berschrift 3. Ebene @ 311 \mod_1418209262291_78.docx @ 2405467 @ 3 @ 1

2.5.2 Direction Information

Pos: 14.6 /Überschriften/Überschriften 3/A-E/B/Begriff "M aschine" @ 337\mod_1430721887716_78.docx @ 2563575 @ 3 @ 1

Direction information in this document such as front, rear, right and left always applies in the direction of travel.

2.5.3 Term “Machine”

Pos: 14.7 /BA/Z u diesem Dokument/Begriff M aschine_Mähwer ke @ 338\mod_1430722216123_78.docx @ 2563731 @ @ 1

Throughout the rest of this document, the mower will also be referred to as the “machine”.

Pos: 14.8 /Überschriften/Überschriften 3/A-E/A/Abbil dungen_Darstellungsmittel @ 336\mod_1430133919063_78.docx @ 2558462 @ 3 @ 1

2.5.4 Figures

Pos: 14.9 /BA/Z u diesem Dokument/Abbildung en_Text @ 336\mod_1430134111209_78.docx @ 2558493 @ @ 1

Pos: 14.10 /Ü berschriften/Ü berschriften 3/U-ZU mfang des D okuments @ 346\mod_1434979896995_78.docx @ 2611366 @ 3 @ 1

The figures in this document do not always represent the exact machine type. The information which refers to the figure always corresponds to the machine type of this document.

2.5.5 Scope of Document

Pos: 14.11 /BA/Z u diesem D okument/U mfang des Dokuments_alle Beipacks und Vari anten enthalten_T ext @ 346 \mod_1434979460226_78.docx @ 2611335 @ @ 1 In addition to standard equipment, accessories kits and versions of the machine are described

Pos: 14.12 /Ü berschriften/Ü berschriften 3/A-E/D /Darstell ungsmittel @ 336\mod_1429865448625_78.docx @ 2556625 @ 3 @ 1 in this document. Your machine may deviate from this document.

2.5.6 Means of representation

Pos: 14.13 /Ü berschriften/Z wischenüberschriften/P-T/Symbole im Text @ 336\mod_1430121354111_78.docx @ 2557539 @ @ 1

Icons in the text

Pos: 14.14 /BA/Z u diesem D okument/D arstellungsmittel_ohne Hi nweis und War nung_BA @ 339\mod_1431002650179_78.docx @ 2570965 @ @ 1

In this document, the following means of representation are used:

Action step

A bullet point (  ) designates an action step you have to perform, as for example:

• Set the left outside mirror.

Sequence of actions

Several bullet points (  ) located in front of a sequence of action steps identify a sequence of actions to be performed step by step, as for example:

• Loosen counter nut.

• Set the screw.

• Tighten counter nut.

List

Dashes (-) identify lists such as, for example:

– Brakes

– Steering

– Lighting

Pos: 14.15 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

8

Pos: 14.16 /Ü berschriften/Z wischenüberschriften/P-T/Symbole in Abbildungen @ 336\mod_1430121455379_78.docx @ 2557570 @ @ 1

Symbols in figures

Pos: 14.17 /BA/Z u diesem D okument/D arstellungsmittel_Ü bersicht Symbole_BA @ 329\mod_1427193088297_78.docx @ 2523598 @ @ 1

To visualize parts and actions steps, the following icons are used:

Icon

1

Explanation

Reference sign for part

I

Position of a part (e.g. move from pos. I to pos. II)

X

Dimensions (e.g. B = width, H = height, L = length)

To this Document

Action step: Tighten screws with torque key with specified tightening torque

Direction of motion

Direction of travel opened closed enlargement of display detail

Framings, dimension line, dimension line limitation, reference line for visible parts or visible mounting material

Framings, dimension line, dimension line limitation, reference line for covered parts or covered mounting material

Laying routes

LH

RH

Left-hand machine side

Right-hand machine side

Pos: 14.18 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

9

To this Document

Pos: 14.19 /Ü berschriften/Z wischenüberschriften/U-Z/Warnhinweise_Z u diesem D okument @ 337\mod_1430720690194_78.docx @ 2563366 @ @ 1

Warning signs

Pos: 14.20 /BA/Z u diesem D okument/Warnhinweise_Z u di esem Dokument_T ext @ 337\mod_1430720301162_78.docx @ 2563335 @ @ 1

Warning

WARNING! - Type and source of hazard!

Effect: Injuries, serious material damage.

• Measures for hazard prevention.

Caution

CAUTION! - Type and source of hazard!

Effect: Damage to property.

• Measures for risk prevention.

Pos: 14.21 /Ü berschriften/Z wischenüberschriften/F-J/Hi nweise mi t Infor mationen und Empfehl ung en_Z u diesem D okument @ 337\mod_1430721734582_78.docx @ 2563548 @ @ 1

Notes with information and recommendations

Pos: 14.22 /BA/Z u diesem D okument/Hi nweise mit Infor mationen und Empfehl ung en_T ext @ 337\mod_1430721371455_78.docx @ 2563487 @ @ 1 Note

Note

Effect: Economic benefit of the machine.

• Measures to be performed.

Pos: 15 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

10

Pos: 16 /Ü berschriften/Überschriften 1/P-T/Sicher heit @ 0\mod_1195566748646_78.docx @ 635 @ 1 @ 1

Safety

3

Pos: 17 /Ü berschriften/Überschriften 2/U-Z/VVerwendungszweck @ 1\mod_1201707246738_78.docx @ 54055 @ 2 @ 1

Safety

3.1

Pos: 18 /BA/Einl eitung/EasyCut/Ver wendungszweck M äher @ 3\mod_1204547495418_78.docx @ 70590 @ @ 1

Purpose of Use

The EasyCut disc mower is used for cutting crops growing on the ground (except maize).

3.2 Intended use

Pos: 19.2 /BA/Einl eitung/Besti mmungsgemäßer Gebr auch/EasyCut/Besti mmungsgemäß er Gebrauch (Ei nzahl) @ 3\mod_1204548357809_78.docx @ 70671 @ @ 1

The disc mower is built exclusively for customary use in agricultural work (intended use).

Pos: 19.3 /BA/Einl eitung/Besti mmungsgemäßer Gebr auch/Nicht besti mmungsgemäß @ 103\mod_1332171672294_78.docx @ 940272 @ @ 1

Unauthorised modifications to the machine may have a negative effect on the machine characteristics or safe and reliable use of the machine or may interfere with proper operation.

Unauthorised modifications shall therefore release the manufacturer of any liability for consequential damage.

Pos: 20 /Ü berschriften/Überschriften 2/K-O/NNutzungsdauer der M aschi ne @ 318\mod_1423658430909_78.docx @ 2465744 @ 2 @ 1

3.3

Pos: 21 /BA/Einl eitung/N utzungsdauer der M aschine_Text @ 318\mod_1423556613022_78.docx @ 2463145 @ @ 1

Service life of the machine

– The service life of this machine strongly depends on proper use and maintenance as well as the operating conditions.

– Permanent operational readiness as well as long service life of the machine can be achieved by observing the instructions and notes of these operating instructions.

– After each season of use, the machine must be checked thoroughly for wear and other damage.

– Damaged and worn parts must be replaced before placing the machine into service again.

– After the machine has been used for five years, carry out full technical inspection of the machine. According to the results of this inspection, a decision concerning the possibility of reuse of the machine should be taken.

– Theoretically, the service life of this machine is unlimited as all worn or damaged parts can be replaced.

Pos: 22 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

11

Safety

Pos: 23.1 /BA/Sicher heit/Sicher heits- und U nfall ver hütungs-Vorschriften Swadr o_Ladewag en_EasyC ut @ 73\mod_1308298589597_78.docx @ 655493 @ 2 @ 1

3.4 Safety Instructions and Accident Prevention Regulations

Pos: 23.2 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

1 Please follow all generally applicable safety and accident prevention regulations in addition to the safety instructions contained in these operating instructions!

2 The attached warning and safety signs provide important information for safe operation. Pay attention to these for your own safety!

3 When using public roads, make sure to observe the applicable traffic regulations!

4 Make sure that you are familiar with all equipment and controls as well as with their functions before you begin working with the machine. It is too late to learn this when you are using the machine for work!

5 The user should wear close fitting clothes. Avoid wearing loose or baggy clothing.

6 Keep the machine clean to prevent the danger of fire!

7 Before starting or moving the machine, make certain that nobody is in the vicinity of the machine! (Watch for children!) Make sure that you have a clear view!

8 Carrying passengers during operation and transport on the working implement is not permitted.

9 Couple implements correctly! Attach and secure implements to specified devices only!

10 When attaching or detaching implements, place the supporting devices in the correct positions!

11 Use extreme caution when attaching or detaching implements onto or from the tractor!

12 Always attach ballast weights properly to the fixing points provided!

13 Observe permitted axle loads, gross weight and transport dimensions!

14 Check and attach transport equipment, such as lighting, warning devices and protective equipment!

15 Actuating mechanisms (cables, chains, linkages etc.) for remote controlled devices must be positioned in such a way that no movements are unintentionally triggered in any transport or working positions.

16 Ensure that implements are in the prescribed condition for on-road travel and lock them in place in accordance with the manufacturer's instructions!

17 Never leave the driver's seat when the vehicle is moving!

18 Always drive at the correct speed for the prevailing driving conditions! Avoid sudden changes in direction when travelling uphill or downhill or across a gradient!

19 Hitched implements and ballast weights affect the driving, steering and braking response of the machine. Make sure that you are able to brake and steer the machine as required!

20 Take into account the extension radius and/or inertia of an implement when turning corners!

21 Start up implements only when all safety devices have been attached and set in the required position!

22 Keep safety equipment in good condition. Replace missing or damaged parts.

23 Keep clear of the working range of the machine at all times!

24 Do not stand within the turning and swivel range of the implement!

25 Never operate the hydraulic folding frames if anyone is inside the swivel range!

26 Parts operated by external power (e.g. hydraulically) can cause crushing and shearing injuries!

27 Before leaving the tractor, lower the implement onto the ground, apply the parking brake, switch off the engine and remove the ignition key!

12

Pos: 23.3 /BA/Sicher heit/Personalqualifi kati on und -schul ung @ 0\mod_1195639383185_78.docx @ 1136 @ 3 @ 1

Safety

3.4.1 Personnel Qualification and Training

The machine may be used, maintained and repaired only by persons who are familiar with it and have been instructed about the dangers connected with it. The operator must define areas of responsibility and monitoring of personnel. Should personnel lack the required knowledge, they must receive the required training and instruction. The operator must ensure that the contents of these operating instructions have been fully understood by personnel.

Repair work not described in these operating instructions should only be performed by

Pos: 23.4 /BA/Sicher heit/Gefahr en bei Nichtbeachtung der Sicherheitshinweise @ 0\mod_1195639434013_78.docx @ 1155 @ 3 @ 1 authorised service centres.

3.4.2

Pos: 23.5 /BA/Sicher heit/Sicher heitsbewusstes Ar beiten_T eil1 @ 0\mod_1195639792576_78.docx @ 1174 @ 3 @ 1

Dangers in Case of Non-compliance with the Safety Instructions

Failure to follow the safety instructions could result in personal injury and environmental hazards as well as damage to the machine. If the safety instructions are not respected, this could result in the forfeiture of any claims for damages.

Failure to follow the safety instructions could result, for example

, in the following hazards:

• Endangering of persons due to not protected working areas.

• Breakdown of important machine functions

• Failure of prescribed methods for repair and maintenance

• Endangering of persons due to mechanical and chemical effects

• Damage to the environment due to leaking hydraulic oil

3.4.3 Safety-conscious work practices

Pos: 23.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Always observe the safety instructions set out in these operating instructions, all existing accident prevention rules and any internal work, operating and safety rules issued by the operator.

The safety and accident prevention regulations of the responsible professional associations are binding.

The safety instructions provided by the vehicle manufacturer should also be observed.

Observe the applicable traffic laws when using public roads.

Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep emergency numbers for doctors and fire brigade close to the telephone.

13

Safety

Pos: 23.7 /BA/Sicher heit/Angebaute Ger äte/Ger äte angebaut EasyC ut @ 3\mod_1204552588996_78.docx @ 70752 @ 2 @ 1

3.5 Attached devices

1 Use extreme caution when attaching or detaching implements onto or from the tractor!

2 Couple the respective application devices to the appropriate couplings (e.g. three-point suspension) only and secure them in a way (transport, use) that excludes inadvertent lifting or lowering of the device.

3 When using three-point linkage, the attachment categories of the tractor and the device

(e.g. PTO speed, hydraulic system) must be coordinated!

4 When using the outside controls for the three-point linkage, do not step between the tractor and the device (risk of injury)!

Pos: 23.8 /BA/Sicher heit/Zapfwellenbetrieb Traktor @ 0\mod_1199699899350_78.docx @ 33264 @ 2 @ 1

3.6 PTO operation

1  Use only PTO shafts specified by the manufacturer!

2  The guard tube and guard cone of the PTO shaft and the PTO guard must be attached and in good working condition (on the implement side, too)!

3  Make sure that the required tube covers are in place for PTO shafts in transport and working position!

4  Before installing or detaching PTO shafts, disengage the PTO, switch off the engine and remove the ignition key!

5  When using PTO shafts with an overload safety or free-running coupling which are not shielded by the guard on the tractor, mount the overload safety or free-running coupling on the implement side!

6  Always make sure that the PTO shaft is properly installed and secured!

7  Attach chains to prevent the PTO shaft guard from rotating with the shaft!

8  Before switching on the PTO, make sure that the selected PTO speed of the tractor matches the permissible implement speed!

9  Before switching on the PTO shaft make sure that no person is in the danger zone of the device!

10  Never switch on the PTO if the engine is switched off!

11  No one should be in the vicinity of the rotating PTO or PTO shaft when the PTO is in use.

12  Always switch off the PTO shaft when the angle is too large or the PTO shaft is not required!

13 Caution! After disengaging the PTO danger due to the flywheel running on! Keep away from the implement during this time. The machine may be worked on only if it is completely at standstill and if the flywheel is secured by the parking brake.

14  Cleaning, lubricating or adjusting PTO driven implements or the PTO shaft only with PTO disengaged, engine switched off and ignition key withdrawn! Secure the fly-wheel with the parking brake.

15  Place the disconnected PTO shaft onto the support provided!

16  After detaching the PTO shaft, attach the protective cover to the PTO end!

17  If damage occurs, correct this immediately before using the implement!

Pos: 23.9 /BA/Sicher heit/Zapfwellenbetrieb Zusatz @ 2\mod_1203524761314_78.docx @ 66513 @ @ 1

Pos: 23.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The instructions of the manufacturer must be observed with regard to the PTO shaft. (separate operating instructions)

14

Pos: 23.11 /BA/Sicherheit/H ydr auli kanl age @ 2\mod_1203503691986_78.docx @ 66225 @ 2 @ 1

Safety

3.7 Hydraulic system

1  The hydraulic system is pressurised!

2  When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are connected as specified!

3  When connecting the hydraulic hoses to the tractor hydraulics, make sure that the hydraulics of both the tractor and the implement have been depressurized!

4  In the case of hydraulic connections between tractor and machine, the coupling sleeves and plugs should be marked to ensure a proper connection! If the connectors are interchanged, the function will be reversed (e. g. raising/lowering) - Risk of accident!

5  When searching for leaks, use suitable aids to avoid the risk of injury!

6  Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause serious injury! Seek medical help immediately should injuries occur! Danger of infection!

7  Before working on the hydraulic system, depressurise the system and switch off the engine!

Pos: 23.12 /BA/Sicherheit/H ydr auli kanl age Z usatz Alterung der H ydr auli kschl auchl eitungen @ 3\mod_1204552944856_78.docx @ 70772 @ @ 1

8 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The new hoses must fulfill the technical requirements set by the manufacturer of the implement!

Pos: 23.13 /BA/Sicherheit/Wartung/Wartung Mäher mit Gasspeicher+ Auswechseln von Arbeitswer kzeug en @ 0\mod_1195647075607_78.docx @ 1442 @ 2 @ 1

3.8 Maintenance

1 Always make certain that the drive and the engine are switched off before doing any repairs, maintenance or cleaning! - Remove the ignition key!

2 Regularly check that nuts and bolts are properly seated and tighten if necessary!

3 When carrying out maintenance work on a raised mowing unit, always use suitable means to secure it against falling.

4 When replacing working tools with cutting edges, use suitable tools and gloves!

5 Oils, greases and filters must be disposed of correctly!

6 Always disconnect the power supply before working on the electrical system!

7 If protective devices and guards are subject to wear, check them regularly and replace them in good time!

8 When performing electrical welding work on the vehicle and mounted devices, turn the power supply off at main battery switch or disconnect generator cable and battery!

9 Replacement parts must at least comply with the technical requirements set by the manufacturer of the implements! This is guaranteed by original KRONE spare parts!

Pos: 23.14 /BA/Sicherheit/Eigenmächtiger Umbau und Ersatzteil herstell ung @ 1\mod_1201937705539_78.docx @ 55745 @ 2 @ 1

10 Only use nitrogen for filling pneumatic accumulators - risk of explosion!

3.9

Pos: 23.15 /BA/Sicherheit/U nzulässige Betriebsweisen @ 11\mod_1223357699923_78.docx @ 145527 @ 2 @ 1

Unauthorised Conversion/Modification and Spare Parts Production

Conversions or modifications of the machine are permitted only with prior consultation with the manufacturer. Original spare parts and accessories authorised by the manufacturer help to ensure safety. Use of other parts may void liability for resulting damage.

3.10

Pos: 24 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Inadmissible Modes of Operation

The operating safety of the delivered machine is guaranteed only when it is used as intended in compliance with the introductory section "Intended use" of the operating instructions. The limit values listed in the data charts should not be exceeded under any circumstances.

15

Machine Description

Pos: 25.1 /Überschriften/Überschriften 1/K-O/Maschi nenbeschr eibung @ 107\mod_1334231806004_78.docx @ 965201 @ 1 @ 1

4

Pos: 25.2 /Überschriften/Überschriften 2/K-O/MMaschi nenübersicht @ 0\mod_1195565731130_78.docx @ 555 @ 2 @ 1

Machine Description

4.1 Machine overview

Pos: 25.3 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut F 320 CV geschoben/EasyC ut F 360 C V geschoben @ 321\mod_1424788432426_78.docx @ 2479787 @ @ 1

EasyCut F 320 CV pushed / EasyCut F 360 CV pushed

Pos: 25.4 /BA/M aschinenbeschrei bung/M aschi nenübersicht/M ähwer ke/M aschinenübersicht EasyC ut F 360 C V geschoben Bild @ 241\mod_1395241558809_78.docx @ 1896635 @ @ 1

2 3

1

4

19

14

5 6 7

18

11 10

20

8

9

10 11

5

12

13

14

Pos: 25.5 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 1

15 17 16

15

EC-525-0

16

Pos: 25.6 /BA/M aschinenbeschrei bung/M aschi nenübersicht/M ähwer ke/M aschinenübersicht EasyC ut F 360 C V geschoben T abelle @ 242 \mod_1395308523079_78.docx @ 1898512 @ @ 1

Pos. Description

1)

3)

Blade drawer

Universal shaft support

5)

7)

Swath flaps

Parking support*)

9) Input gearbox

11) Intermediate universal shaft

13) Lever to adjust the conditioner plate

15) Guard cloth

17) Safety device front

19) Blade key*)

*) optional

Pos: 25.7 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description

Pos. Description

2) Drive universal shaft

4)

6)

Relief springs

Tine conditioner / roller conditioner

8) Guard cloth

10) Friction clutch

12) Angular gearbox

14) Side guards

16) Cutter bar

18) Belt drive

20) Retaining chains

17

Machine Description

Pos: 25.8 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut F 320 CVg ezog en/EasyC ut F 360 C V gezogen @ 321\mod_1424790641735_78.docx @ 2479988 @ @ 1

EasyCut F 320 CV trailed / EasyCut F 360 CV trailed

Pos: 25.9 /BA/M aschinenbeschrei bung/M aschi nenübersicht/M ähwer ke/M aschinenübersicht EasyC ut F 360 C V gezogen Bild @ 242\mod_1395309564639_78.docx @ 1898648 @ @ 1

3 4

2

1

19

5

18

6 7

11

10

8

9

10 11

14

5

12

13

14

15

Pos: 25.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 2

17 16

15

EC-524-0

18

Pos: 25.11 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/M ähwer ke/Maschi nenübersicht EasyCut F 360 CV gezogen T abelle @ 241\mod_1395304263736_78.docx @ 1897864 @ @ 1

Pos. Description

1)

3)

5)

Blade drawer

Universal shaft support

Swath flap

Pos: 25.12 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

7)

9)

Parking support*)

Input gearbox

11) Intermediate universal shaft

13) Lever to adjust the conditioner plate

15) Guard cloth

17) Safety device front

19) Blade key*)

*) optional

Machine Description

Pos. Description

2) Drive universal shaft

4)

6)

Relief springs

Tine conditioner / roller conditioner

8) Guard cloth

10) Friction clutch

12) Angular gearbox

14) Side guards

16) Cutter bar

18) Belt drive

19

Machine Description

Pos: 25.13 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut F 360 CR geschoben @ 242 \mod_1395395062772_78.docx @ 1900444 @ @ 1

EasyCut F 360 CR pushed

Pos: 25.14 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/M ähwer ke/Maschi nenübersicht EasyCut F 360 CR g eschoben Bild _1 @ 261\mod_1399444843585_78.docx @ 1991686 @ @ 1

1

2 3

4

18

14

5 6 7

19

8

9

10 11

5

12

13

14

16

15

EC-478-0

Pos: 25.15 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 3

15

17

20

Pos: 25.16 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/M ähwer ke/Maschi nenübersicht EasyCut F 360 CR geschoben T abelle @ 241 \mod_1395242894024_78.docx @ 1896929 @ @ 1

Pos. Description

1)

3)

Blade drawer

Universal shaft support

5)

7)

Swath flaps

Parking support*)

9) Input gearbox

11) Intermediate universal shaft

13) Lever to adjust the conditioner plate

15) Guard cloth

17) Safety device front

19) Retaining chains

*) optional

Pos: 25.17 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description

Pos. Description

2) Drive universal shaft

4)

6)

Relief springs

Tine conditioner / roller conditioner

8) Guard cloth

10) Friction clutch

12) Angular gearbox

14) Side guards

16) Cutter bar

18) Blade key*)

21

Machine Description

Pos: 25.18 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut F 360 CR gezogen @ 242\mod_1395394970276_78.docx @ 1900335 @ @ 1

EasyCut F 360 CR trailed

Pos: 25.19 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/M ähwer ke/Maschi nenübersicht EasyCut F 360 CR g ezog en Bild @ 242\mod_1395309680566_78.docx @ 1898677 @ @ 1

1

2

3

4

18

14

5 6

7

8

9

10 11

5

12

13

14

15

Pos: 25.20 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 4

17 16

15

EC-479-0

22

Pos: 25.21 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/M ähwer ke/Maschi nenübersicht EasyCut F 360 CR gezogen T abell e @ 242\mod_1395308755080_78.docx @ 1898591 @ @ 1

Pos. Description

1)

3)

5)

Blade drawer

Universal shaft support

Swath flap

7)

9)

Parking support*)

Input gearbox

11) Intermediate universal shaft

13) Lever to adjust the conditioner plate

15) Guard cloth

17) Safety device front

*) optional

Pos: 26 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine Description

Pos. Description

2) Drive universal shaft

4)

6)

Relief springs

Tine conditioner / roller conditioner

8) Guard cloth

10) Friction clutch

12) Angular gearbox

14) Side guards

16) Cutter bar

18) Blade key*)

23

Machine Description

Pos: 27 /Ü berschriften/Überschriften 2/K-O/KKennzeichnung @ 0\mod_1195564622099_78.docx @ 496 @ 3 @ 1

4.2 Identification Plate

Pos: 28 /BA/Einl eitung/Kennzeichnung/EasyCut/Kennzeichnung EasyC ut F 360 C V/CR @ 242\mod_1395322288613_78.docx @ 1898706 @ @ 1

Jahr

Année

Type

Maschinenfabrik Bernard Krone GmbH

Heinrich-Krone-Straße 10, D 48480 Spelle

Masch. Nr

No. de sér ie

Made in

W.-Ger m any

1

EC-480-0

Fig. 5

The machine data are specified on the type plate (1).

Pos: 29 /BA/Einl eitung/Kennzeichnung/Angaben für Anfr age und Bestellungen_M aschnr . (2015- 11- 04 15:38:15) @ 9\mod_1220507505930_78.docx @ 126110 @ 2 @ 1

4.3

Pos: 30 /Ü berschriften/Überschriften 3/A-E/A/Ansprechpartner @ 0\mod_1195569394286_78.docx @ 839 @ 3 @ 1

Information Required for Questions and Orders

Year

Mach. No.

Type

Note

The entire identification plate represents a legal document and should not be altered or rendered illegible!

When asking questions concerning the machine or ordering spare parts, be sure to provide type designation, machine number and the year of manufacture of the relevant machine: To ensure that these data are always available, we recommend that you enter them in the fields above.

Note

Authentic KRONE spare parts and accessories authorised by the manufacturer help to ensure safety. The use of spare parts, accessories or additional equipment not manufactured, tested or approved by KRONE will exclude any liability for consequential damage.

4.3.1 Contact

Pos: 31 /BA/AdressenAdresse M aschinenfabri k KRON E Spell e @ 444\mod_1460097223706_78.docx @ 3031795 @ @ 1 Maschinenfabrik Bernard Krone GmbH & Co. KG

Heinrich-Krone-Strasse 10

D-48480 Spelle (Germany)

Telephone: + 49 (0) 59 77/935-0 (Head Office)

Fax.: + 49 (0) 59 77/935-339 (Head Office)

Fax.: + 49 (0) 59 77/935-239 (Spare parts - domestic)

Fax.: + 49 (0) 59 77/935-359 (Spare parts - export)

Email: [email protected]

Pos: 34 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

24

Pos: 35 /BA/Sicher heit/EasyC ut/Sicher hei t Ei nführung EasyC ut @ 3\mod_1204553763950_78.docx @ 70812 @ 3 @ 1

Machine Description

4.4 Introduction

The disc mower is equipped with all safety devices (protective devices). However, it is not possible to eliminate all potential hazards on this machine as this would impair its full functional capability. Hazard warnings are attached to the machine in the relevant areas to warn against any dangers. The safety instructions are provided in the form of so-called warning pictograms.

Important information on the position of these safety signs and what they mean is given below!

Pos: 36 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/Warnung - Beschädigte oder unlesbare Warnbildzeichen @ 120\mod_1343305789479_78.docx @ 1099853 @ @ 1

WARNING!

Danger of injury on machine parts if danger zones have not been marked when warning pictograms are missing, damaged or illegible.

Danger of injury due to dangerous parts and other residual risks as users or third parties enter the danger area or reach into it as they are not aware of the danger.

• Immediately replace damaged or illegible labels.

• Following repair work, always attach appropriate adhesive safety labels to all the replaced, modified or repaired components.

• Never clean areas carrying an adhesive safety label using a high-pressure cleaner.

Familiarise yourself with the statement of the warning pictograms. The adjacent text and the selected location on the machine provide information on the special danger spots on the machine.

Pos: 37 /BA/Sicher heit/6. Ü ber arbeitete War nhi nweise/Hi nweis - N achbestellung/ Anbringung Aufkleber @ 357\mod_1438760742670_78.docx @ 2656419 @ 33 @ 1

4.4.1 Re-Ordering Safety Labels and Information Labels

Note

Each safety and information label is provided with an order number and can be ordered directly from the manufacturer or from authorised dealer (refer to chapter “Contact Person”).

4.4.2

Pos: 38 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Attaching Safety Labels and Information Labels

Note - Attaching a label

Effect: Adhesion of label

• The attachment area must be clean, dry and free from dirt, oil and grease.

25

Machine Description

Pos: 39 /Ü berschriften/Überschriften 2/K-O/LLage der Sicher hei tsaufkl eber an der M aschine @ 0\mod_1195634967326_78.docx @ 1020 @ 3 @ 1

4.5 Position of the Adhesive Safety Stickers on the Machine

Pos: 40.1 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut C V geschoben @ 334\mod_1429161754066_78.docx @ 2546595 @ @ 1

EasyCut CV pushed

2

1 5

4

4

4

4

3

Pos: 40.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 6

3

6

26

Pos: 40.4 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 471 1 ( 1x) Bestell-Nr. @ 189\mod_1381220124664_78.docx @ 1622309 @ @ 1

1) Order no. 939 471 1 (1x)

Machine Description

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

• Before starting up the machine, read and follow the operating instructions and safety instructions.

Pos: 40.6 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 ( 1x) Bestell-Nr. @ 198\mod_1384850393482_78.docx @ 1672362 @ @ 1

2) Order no. 939 101 4 (1x)

Pos: 40.7 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 Bild/Text @ 198\mod_1384850409063_78.docx @ 1672391 @ @ 1

MAX.

MAX.

200

939 101- 4 bar

Pos: 40.8 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 576 0 ( 4x) Bestell-Nr. @ 301\mod_1413460410193_78.docx @ 2349935 @ @ 1

3) Order No. 939 576 0 (4x)

Danger due to exceeding the maximum permissible PTO speed or the maximum permissible operating pressure.

If the permissible PTO speed is exceeded, machine parts may be destroyed or flung out.

If the maximum permissible operating pressure is exceeded, hydraulic components may be damaged.

As a result, people may be seriously or fatally injured.

• Observe the permissible PTO speed.

• Observe the permissible operating pressure. a) b) c) a b c a)

Danger from turning machine parts

There is a risk of injury as machine parts may still continue to run for a certain time after being switched off

• Do not touch any moving parts of the machine.

• Wait until the machine parts have come to a complete stop. b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Before start-up, move guards into protective position. c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

Pos: 40.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

27

Machine Description

Pos: 40.11 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut CV geschoben @ 334\mod_1429161754066_78.docx @ 2546595 @ @ 1

EasyCut CV pushed

2

1 5

4

4

3

Pos: 40.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 7

4

4

3

6

28

Pos: 40.14 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 (4x) Bestell-Nr. @ 301\mod_1413467207142_78.docx @ 2349997 @ @ 1

4) Order No. 942 197 1 (4x)

Pos: 40.15 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 Bild/T ext @ 194\mod_1383550461204_78.docx @ 1649212 @ @ 1

Machine Description

Danger from objects being flung out.

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

942 197- 1

Pos: 40.16 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 ( 1x) Bestell-Nr. @ 321\mod_1424857441351_78.docx @ 2481057 @ @ 1

5) Order no. 939 106-3 (1x)

Pos: 40.17 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 Bild/Text @ 321\mod_1424855157789_78.docx @ 2481026 @ @ 1

Danger to life when exceeding the maximum permissible PTO speed.

When exceeding the permissible PTO speed, machine parts may be destroyed or be ejected at high speeds.

This can cause serious personal injuries.

• Observe the permissible PTO speed.

Pos: 40.18 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 002 4 (1x) Bestell-Nr. @ 189\mod_1381220137082_78.docx @ 1622338 @ @ 1

6) Order no. 942 002 4 (1x)

Pos: 40.19 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 002 4 Bild/T ext @ 189\mod_1381212442497_78.docx @ 1621655 @ @ 1

Danger due to rotating machine parts.

When the machine is running, there is a risk of injury due to rotating machine parts.

• Before starting up, move the guards into their protective position.

Pos: 41 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

29

Machine Description

Pos: 42.1 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut CR g eschoben @ 334\mod_1429162424839_78.docx @ 2546626 @ @ 1

EasyCut CR pushed

1 2 5

4

4

3

Pos: 42.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 8

4

3

4

30

Pos: 42.4 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 471 1 ( 1x) Bestell-Nr. @ 189\mod_1381220124664_78.docx @ 1622309 @ @ 1

1) Order no. 939 471 1 (1x)

Machine Description

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

• Before starting up the machine, read and follow the operating instructions and safety instructions.

Pos: 42.6 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 ( 1x) Bestell-Nr. @ 198\mod_1384850393482_78.docx @ 1672362 @ @ 1

2) Order no. 939 101 4 (1x)

Pos: 42.7 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 Bild/Text @ 198\mod_1384850409063_78.docx @ 1672391 @ @ 1

MAX.

MAX.

200

939 101- 4 bar

Pos: 42.8 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 576 0 ( 4x) Bestell-Nr. @ 301\mod_1413460410193_78.docx @ 2349935 @ @ 1

3) Order No. 939 576 0 (4x)

Danger due to exceeding the maximum permissible PTO speed or the maximum permissible operating pressure.

If the permissible PTO speed is exceeded, machine parts may be destroyed or flung out.

If the maximum permissible operating pressure is exceeded, hydraulic components may be damaged.

As a result, people may be seriously or fatally injured.

• Observe the permissible PTO speed.

• Observe the permissible operating pressure. a) b) c) a b c a)

Danger from turning machine parts

There is a risk of injury as machine parts may still continue to run for a certain time after being switched off

• Do not touch any moving parts of the machine.

• Wait until the machine parts have come to a complete stop. b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Before start-up, move guards into protective position. c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

Pos: 42.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

31

Machine Description

Pos: 42.11 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut CR geschoben @ 334\mod_1429162424839_78.docx @ 2546626 @ @ 1

EasyCut CR pushed

1 2 5

4

4

3

Pos: 42.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 9

4

3

4

32

Pos: 42.14 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 (4x) Bestell-Nr. @ 301\mod_1413467207142_78.docx @ 2349997 @ @ 1

4) Order No. 942 197 1 (4x)

Pos: 42.15 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 Bild/T ext @ 194\mod_1383550461204_78.docx @ 1649212 @ @ 1

Machine Description

Danger from objects being flung out.

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

942 197- 1

Pos: 42.16 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 ( 1x) Bestell-Nr. @ 321\mod_1424857441351_78.docx @ 2481057 @ @ 1

5) Order no. 939 106-3 (1x)

Pos: 42.17 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 Bild/Text @ 321\mod_1424855157789_78.docx @ 2481026 @ @ 1

Danger to life when exceeding the maximum permissible PTO speed.

When exceeding the permissible PTO speed, machine parts may be destroyed or be ejected at high speeds.

This can cause serious personal injuries.

• Observe the permissible PTO speed.

Pos: 45 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

33

Machine Description

Pos: 46.1 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut C V gezogen @ 334\mod_1429163536948_78.docx @ 2546657 @ @ 1

EasyCut CV trailed

7 8

1 2 5

4

4

3

Pos: 46.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 10

6

4

3

7

4

EC-512-1

34

Pos: 46.4 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 471 1 ( 1x) Bestell-Nr. @ 189\mod_1381220124664_78.docx @ 1622309 @ @ 1

1) Order no. 939 471 1 (1x)

Machine Description

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

• Before starting up the machine, read and follow the operating instructions and safety instructions.

Pos: 46.6 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 ( 1x) Bestell-Nr. @ 198\mod_1384850393482_78.docx @ 1672362 @ @ 1

2) Order no. 939 101 4 (1x)

Pos: 46.7 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 Bild/Text @ 198\mod_1384850409063_78.docx @ 1672391 @ @ 1

MAX.

MAX.

200

939 101- 4 bar

Pos: 46.8 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 576 0 ( 4x) Bestell-Nr. @ 301\mod_1413460410193_78.docx @ 2349935 @ @ 1

3) Order No. 939 576 0 (4x)

Danger due to exceeding the maximum permissible PTO speed or the maximum permissible operating pressure.

If the permissible PTO speed is exceeded, machine parts may be destroyed or flung out.

If the maximum permissible operating pressure is exceeded, hydraulic components may be damaged.

As a result, people may be seriously or fatally injured.

• Observe the permissible PTO speed.

• Observe the permissible operating pressure. a) b) c) a b c a)

Danger from turning machine parts

There is a risk of injury as machine parts may still continue to run for a certain time after being switched off

• Do not touch any moving parts of the machine.

• Wait until the machine parts have come to a complete stop. b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Before start-up, move guards into protective position. c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

Pos: 46.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

35

Machine Description

Pos: 46.11 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut CV gezogen @ 334\mod_1429163536948_78.docx @ 2546657 @ @ 1

EasyCut CV trailed

7 8

1 2 5

4

4

3

Pos: 46.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 11

6

4

3

7

4

EC-512-1

36

Pos: 46.14 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 (4x) Bestell-Nr. @ 301\mod_1413467207142_78.docx @ 2349997 @ @ 1

4) Order No. 942 197 1 (4x)

Pos: 46.15 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 Bild/T ext @ 194\mod_1383550461204_78.docx @ 1649212 @ @ 1

Machine Description

Danger from objects being flung out.

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

942 197- 1

Pos: 46.16 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 ( 1x) Bestell-Nr. @ 321\mod_1424857441351_78.docx @ 2481057 @ @ 1

5) Order no. 939 106-3 (1x)

Pos: 46.17 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 Bild/Text @ 321\mod_1424855157789_78.docx @ 2481026 @ @ 1

Danger to life when exceeding the maximum permissible PTO speed.

When exceeding the permissible PTO speed, machine parts may be destroyed or be ejected at high speeds.

This can cause serious personal injuries.

• Observe the permissible PTO speed.

Pos: 46.18 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 002 4 (1x) Bestell-Nr. @ 189\mod_1381220137082_78.docx @ 1622338 @ @ 1

6) Order no. 942 002 4 (1x)

Pos: 46.19 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 002 4 Bild/T ext @ 189\mod_1381212442497_78.docx @ 1621655 @ @ 1

Pos: 46.20 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 196 1 (2x) Bestell-Nr. @ 271\mod_1402898285840_78.docx @ 2044144 @ @ 1

7) Order no. 942 196 1 (2x)

Pos: 46.21 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 196 1 Bild/T ext @ 203\mod_1386061378150_78.docx @ 1698142 @ @ 1

Danger due to rotating machine parts.

When the machine is running, there is a risk of injury due to rotating machine parts.

• Before starting up, move the guards into their protective position.

Danger due to crushing or shearing

Risk of injury due to crushing or shearing points on moving machine parts.

• While parts are moving, never reach into areas where there is a risk of being crushed.

942 196 -1

Pos: 46.22 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /27 002/27 002 459 0 ( 1x) Bestell-Nr. @ 242\mod_1395645684119_78.docx @ 1901954 @ @ 1

8) Order No. 27 002 459 0 (1x)

Pos: 46.23 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /27 002/27 002 459 0 Bild/T ext @ 242\mod_1395645665755_78.docx @ 1901925 @ @ 1

Danger due to machine parts that fold down or swivel out unintentionally

Danger of injury for road users due to machine parts that fold down or swivel out unintentionally.

• Each time before transporting the machine or driving on roads, make sure that the stop cock is closed.

27 002 459 0

Pos: 47 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

37

Machine Description

Pos: 48.1 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut CR g ezogen @ 334\mod_1429164050142_78.docx @ 2547069 @ @ 1

EasyCut CR trailed

6 7

1 2 5

4 4

3

Pos: 48.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 12

3

6

4 4

EC-538-0

38

Pos: 48.4 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 471 1 ( 1x) Bestell-Nr. @ 189\mod_1381220124664_78.docx @ 1622309 @ @ 1

1) Order no. 939 471 1 (1x)

Machine Description

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

• Before starting up the machine, read and follow the operating instructions and safety instructions.

Pos: 48.6 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 ( 1x) Bestell-Nr. @ 198\mod_1384850393482_78.docx @ 1672362 @ @ 1

2) Order no. 939 101 4 (1x)

Pos: 48.7 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 101 4 Bild/Text @ 198\mod_1384850409063_78.docx @ 1672391 @ @ 1

MAX.

MAX.

200

939 101- 4 bar

Pos: 48.8 /BA/Sicher heit/4. Sicherheitsaufkleber/EU - ISO /939/939 576 0 ( 4x) Bestell-Nr. @ 301\mod_1413460410193_78.docx @ 2349935 @ @ 1

3) Order No. 939 576 0 (4x)

Danger due to exceeding the maximum permissible PTO speed or the maximum permissible operating pressure.

If the permissible PTO speed is exceeded, machine parts may be destroyed or flung out.

If the maximum permissible operating pressure is exceeded, hydraulic components may be damaged.

As a result, people may be seriously or fatally injured.

• Observe the permissible PTO speed.

• Observe the permissible operating pressure. a) b) c) a b c a)

Danger from turning machine parts

There is a risk of injury as machine parts may still continue to run for a certain time after being switched off

• Do not touch any moving parts of the machine.

• Wait until the machine parts have come to a complete stop. b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Before start-up, move guards into protective position. c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

Pos: 48.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

39

Machine Description

Pos: 48.11 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut CR gezogen @ 334\mod_1429164050142_78.docx @ 2547069 @ @ 1

EasyCut CR trailed

6 7

1 2 5

4 4

3

Pos: 48.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 13

3

6

4 4

EC-538-0

40

Pos: 48.14 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 (4x) Bestell-Nr. @ 301\mod_1413467207142_78.docx @ 2349997 @ @ 1

4) Order No. 942 197 1 (4x)

Pos: 48.15 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 197 1 Bild/T ext @ 194\mod_1383550461204_78.docx @ 1649212 @ @ 1

Machine Description

Danger from objects being flung out.

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

• Keep your distance when the machine is running.

942 197- 1

Pos: 48.16 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 ( 1x) Bestell-Nr. @ 321\mod_1424857441351_78.docx @ 2481057 @ @ 1

5) Order no. 939 106-3 (1x)

Pos: 48.17 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /939/939 106-3 Bild/Text @ 321\mod_1424855157789_78.docx @ 2481026 @ @ 1

Danger to life when exceeding the maximum permissible PTO speed.

When exceeding the permissible PTO speed, machine parts may be destroyed or be ejected at high speeds.

This can cause serious personal injuries.

• Observe the permissible PTO speed.

Pos: 48.18 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 196 1 (2x) Bestell-Nr. @ 271\mod_1402898285840_78.docx @ 2044144 @ @ 1

6) Order no. 942 196 1 (2x)

Pos: 48.19 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /942/942 196 1 Bild/T ext @ 203\mod_1386061378150_78.docx @ 1698142 @ @ 1

Danger due to crushing or shearing

Risk of injury due to crushing or shearing points on moving machine parts.

• While parts are moving, never reach into areas where there is a risk of being crushed.

942 196 -1

Pos: 48.20 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /27 002/27 002 459 0 ( 1x) Bestell-Nr. @ 242\mod_1395645684119_78.docx @ 1901954 @ @ 1

7) Order No. 27 002 459 0 (1x)

Pos: 48.21 /BA/Sicherheit/4. Sicher hei tsaufkl eber/EU - ISO /27 002/27 002 459 0 Bild/T ext @ 242\mod_1395645665755_78.docx @ 1901925 @ @ 1

Danger due to machine parts that fold down or swivel out unintentionally

Danger of injury for road users due to machine parts that fold down or swivel out unintentionally.

• Each time before transporting the machine or driving on roads, make sure that the stop cock is closed.

27 002 459 0

Pos: 51 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

41

Technical Data of the Machine

Pos: 52.1 /Überschriften/Überschriften 1/P-T/T echnische D aten der M aschine @ 134\mod_1351154219999_78.docx @ 1195165 @ 1 @ 1

5

Pos: 52.2 /BA/Einl eitung/T echnische D aten/Technische Daten mit 2. Ü berschrift @ 0\mod_1195566374865_78.docx @ 594 @ 2 @ 1

Technical Data of the Machine

5.1 Technical data

All information, illustrations and technical data in these operating instructions correspond to the latest state at the time of publication. We reserve the right to make design changes at any time and without notification of reasons.

Pos: 52.3 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut F 320 CV geschoben @ 326\mod_1425976956002_78.docx @ 2502845 @ @ 1

EasyCut F 320 CV pushed

Pos: 52.4 /BA/Einl eitung/T echnische D aten/EasyC ut/EasyC ut F 320 C V/CR/T echnische D aten: Abmessung en EasyC ut F 320 C V geschobe n @ 326\mod_1425977992628_78.docx @ 2503028 @ @ 1

Dimensions

Working width

Transport width

Swath width

Width of conditioner system

Acreage output

Dead weight

Pos: 52.5 /BA/Einl eitung/T echnische D aten/EasyC ut/EasyC ut F 320 C V/CR/T echnische D aten: Mindestanfor der ung an den Tr aktor EasyC ut F 320 C V / 60 kW (82 PS) @ 332\mod_1428584396157_78.docx @ 2540455 @ @ 1

3160 mm

3000 mm

1300 mm – 2700 mm

2500 mm

3.5 – 4 ha/h approx. 1225 kg

Minimum tractor requirements

Power requirement

PTO speed

Pos: 52.6 /BA/Einl eitung/T echnische D aten/EasyC ut/EasyC ut F 320 C V/F 360 C V/CR /Technische Daten: H ydr auli kanschl üsse EasyCut F 320 CV/ EasyC ut F 360 C V/CR geschoben @ 243\mod_1395657440240_78.docx @ 1903034 @ @ 1

Hydraulic connections

For the hydraulically folding outer guards version

60 kW (82 HP) max. 1000 rpm

1x double-action control unit

Pos: 52.7 /BA/Einl eitung/T echnische D aten/EasyC ut/EasyC ut F 320 C V/F 360 C V/CR /Technische Daten: Ausrüstung der M aschine ( Seri e) EasyC ut F 320 C V @ 326\mod_1425981375290_78.docx @ 2503161 @ @ 1

Pos: 52.8 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine equipment (series)

SafeCut

Blade quick fastener

Input gearbox

Tine conditioner

Belt drive

Mechanical spring relief

Number of cutting discs

Number of mower drums

Series

Series

Series

Series

600 / 900 rpm

Series

5 units

2 units

42

Pos: 52.9 /Abkürzungen /Abkürzungen Beschr eibung/EasyCut F 320 CV gezogen @ 326\mod_1425990136978_78.docx @ 2503357 @ @ 1

EasyCut F 320 CV trailed

Pos: 52.10 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Abmessungen EasyC ut F 320 C V gezogen @ 326\mod_1425991152797_78.docx @ 2503448 @ @ 1

Dimensions

Working width

Transport width

Swath width

Width of conditioner system

Acreage output

Dead weight

Pos: 52.11 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/CR /T echnische Daten: Mindestanforderung an den Traktor EasyC ut F 320 C V / 60 kW ( 82 PS) @ 332\mod_1428584396157_78.docx @ 2540455 @ @ 1

Minimum tractor requirements

Power requirement

PTO speed

Pos: 52.12 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: H ydrauli kanschl üsse EasyC ut F 360 CV/CR gezogen @ 243\mod_1395659959856_78.docx @ 1903540 @ @ 1

Hydraulic connections

For the hydraulically folding outer guards version

For trailed headstock design

Pos: 52.13 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Ausr üstung der M aschine (Serie) EasyCu t F 320 CV @ 326\mod_1425981375290_78.docx @ 2503161 @ @ 1

Pos: 52.14 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine equipment (series)

SafeCut

Blade quick fastener

Input gearbox

Tine conditioner

Belt drive

Mechanical spring relief

Number of cutting discs

Number of mower drums

Technical Data of the Machine

3160 mm

3000 mm

1300 mm – 2700 mm

2420 mm

3,5 – 4 ha/h ca. 1385 kg

60 kW (82 HP) max. 1000 rpm

1x double-action control unit

1x single-action control unit

Series

Series

Series

Series

600 / 900 rpm

Series

5 units

2 units

43

Technical Data of the Machine

Pos: 52.15 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut F 360 C V g eschoben @ 326\mod_1425985005741_78.docx @ 2503295 @ @ 1

EasyCut F 360 CV pushed

Pos: 52.16 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Abmessungen EasyC ut F 360 C V geschoben @ 243\mod_1395658316432_78.docx @ 1903241 @ @ 1

Dimensions

Working width

Transport width

Swath width

Width of conditioner system

Acreage output

Dead weight

Pos: 52.17 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/CR /T echnische Daten: Mindestanforderung an den Traktor EasyC ut F 320 M / F 360 CV/CR / 66 kW (90 PS) @ 235\mod_1394182173131_78.docx @ 1868899 @ @ 1

Minimum tractor requirements

Power requirement

PTO speed

Pos: 52.18 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: H ydrauli kanschl üsse EasyC ut F 320 C V/ EasyC ut F 360 C V/CR geschoben @ 243\mod_1395657440240_78.docx @ 1903034 @ @ 1

Hydraulic connections

For the hydraulically folding outer guards version

Pos: 52.19 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Ausr üstung der M aschine (Serie) EasyCut F 360 CV @ 326\mod_1425996638221_78.docx @ 2503690 @ @ 1

Pos: 52.20 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine equipment (series)

SafeCut

Blade quick fastener

Input gearbox

Tine conditioner

Lighting

Belt drive

Mechanical spring relief

Number of cutting discs

Number of mower drums

3600 mm

3450 mm

1300 mm – 2700 mm

2500 mm

3.5 – 4 ha/h approx. 1285 kg

60 kW (82 HP) max. 1000 rpm

1x double-action control unit

Series

Series

Series

Series

Series

600 / 900 rpm

Series

6 units

2 units

44

Pos: 52.21 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut F 360 C V g ezog en @ 326\mod_1425985008767_78.docx @ 2503326 @ @ 1

EasyCut F 360 CV trailed

Pos: 52.22 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Abmessungen EasyC ut F 360 C V gezogen @ 243\mod_1395666374298_78.docx @ 1903946 @ @ 1

Dimensions

Working width

Transport width

Swath width

Width of conditioner system

Acreage output

Dead weight

Pos: 52.23 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/CR /T echnische Daten: Mindestanforderung an den Traktor EasyC ut F 320 M / F 360 CV/CR / 66 kW (90 PS) @ 235\mod_1394182173131_78.docx @ 1868899 @ @ 1

Minimum tractor requirements

Power requirement

PTO speed

Pos: 52.24 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: H ydrauli kanschl üsse EasyC ut F 360 CV/CR gezogen @ 243\mod_1395659959856_78.docx @ 1903540 @ @ 1

Hydraulic connections

For the hydraulically folding outer guards version

For trailed headstock design

Pos: 52.25 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Ausr üstung der M aschine (Serie) EasyCut F 360 CV @ 326\mod_1425996638221_78.docx @ 2503690 @ @ 1

Pos: 52.26 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine equipment (series)

SafeCut

Blade quick fastener

Input gearbox

Tine conditioner

Lighting

Belt drive

Mechanical spring relief

Number of cutting discs

Number of mower drums

Technical Data of the Machine

3600 mm

3450 mm

1300 mm – 2700 mm

2500 mm

3.5 – 4 ha/h approx. 1450 kg

60 kW (82 HP) max. 1000 rpm

1x double-action control unit

1x single-action control unit

Series

Series

Series

Series

Series

600 / 900 rpm

Series

6 units

2 units

45

Technical Data of the Machine

Pos: 52.27 /Abkürzungen /Abkürzung en Beschrei bungEasyC ut F 360 CR g eschoben @ 242\mod_1395395062772_78.docx @ 1900444 @ @ 1

EasyCut F 360 CR pushed

Pos: 52.28 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Abmessungen EasyC ut F 360 CR geschoben @ 243\mod_1395666180253_78.docx @ 1903917 @ @ 1

Dimensions

Working width

Transport width

Swath width

Width of conditioner system

Acreage output

Dead weight

Pos: 52.29 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/CR /T echnische Daten: Mindestanforderung an den Traktor EasyC ut F 320 M / F 360 CV/CR / 66 kW (90 PS) @ 235\mod_1394182173131_78.docx @ 1868899 @ @ 1

Minimum tractor requirements

Power requirement

PTO speed

Pos: 52.30 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: H ydrauli kanschl üsse EasyC ut F 320 C V/ EasyC ut F 360 C V/CR geschoben @ 243\mod_1395657440240_78.docx @ 1903034 @ @ 1

Hydraulic connections

For the hydraulically folding outer guards version

Pos: 52.31 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Ausr üstung der M aschine (Serie) EasyCut F 360 CR @ 326\mod_1425996868242_78.docx @ 2503721 @ @ 1

Pos: 52.32 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Machine equipment (series)

SafeCut

Blade quick fastener

Input gearbox

Roller conditioner

Lighting

Angular gearbox

Mechanical spring relief

Number of cutting discs

Number of mower drums

3600 mm

3450 mm

1300 mm – 2700 mm

2500 mm

3.5 – 4 ha/h approx. 1289 kg

60 kW (82 HP) max. 1000 rpm

1x double-action control unit

Series

Series

Series

Series

Series

600 / 900 rpm

Series

6 units

2 units

46

Pos: 52.33 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut F 360 CR gezogen @ 242\mod_1395394970276_78.docx @ 1900335 @ @ 1

EasyCut F 360 CR trailed

Pos: 52.34 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Abmessungen EasyC ut F 360 CR gezogen @ 243\mod_1395668267383_78.docx @ 1904239 @ @ 1

Dimensions

Working width

Transport width

Swath width

Width of conditioner system

Acreage output

Dead weight

Pos: 52.35 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/CR /T echnische Daten: Mindestanforderung an den Traktor EasyC ut F 320 M / F 360 CV/CR / 66 kW (90 PS) @ 235\mod_1394182173131_78.docx @ 1868899 @ @ 1

Minimum tractor requirements

Power requirement

PTO speed

Pos: 52.36 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: H ydrauli kanschl üsse EasyC ut F 360 CV/CR gezogen @ 243\mod_1395659959856_78.docx @ 1903540 @ @ 1

Hydraulic connections

For the hydraulically folding outer guards version

For trailed headstock design

Pos: 52.37 /BA/Ei nlei tung/T echnische Daten/EasyCut/EasyCut F 320 CV/F 360 C V/CR/T echni sche D aten: Ausr üstung der M aschine (Serie) EasyCut F 360 CR @ 326\mod_1425996868242_78.docx @ 2503721 @ @ 1

Machine equipment (series)

SafeCut

Blade quick fastener

Input gearbox

Roller conditioner

Lighting

Angular gearbox

Mechanical spring relief

Number of cutting discs

Number of mower drums

Pos: 53 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Technical Data of the Machine

3600 mm

3450 mm

1300 mm – 2700 mm

2500 mm

3.5 – 4 ha/h approx. 1469 kg

60 kW (82 HP) max. 1000 rpm

1x double-action control unit

1x single-action control unit

Series

Series

Series

Series

Series

600 / 900 rpm

Series

6 units

2 units

47

Technical Data of the Machine

Pos: 54 /Ü berschriften/Überschriften 2/A-E/BBetriebsstoffe @ 174\mod_1371620600320_78.docx @ 1490571 @ 2 @ 1

5.2 Consumables

Pos: 55 /BA/Wartung/U mweltHinweis U mwelt Betriebsstoffe entsorgen und l ager n @ 418\mod_1453711567284_78.docx @ 2927531 @ @ 1

CAUTION!

Environmental damage caused by incorrect storage and dispose of consumables!

Pos: 56 /Abkürzungen /Abkürzungen sprachneutr al/EasyC ut/EasyC ut F 320 C V @ 116\mod_1340791546095_0.docx @ 1019515 @ @ 1

• Store consumables in suitable containers according to statutory provisions.

• Dispose of used consumables according to statutory provisions.

EasyCut F 320 CV

Pos: 57 /BA/Wartung/T abellen_Füll meng en/Mähwer ke/T echnische D aten Betri ebsstoffe F üllmengen EC F 320 CV @ 381\mod_1444113868385_78.docx @ 2751559 @ @ 1

Designation Filling quantity

Input gearbox

Angular gearbox

1.7 l

0.9 l

Cutterbar 7.0 l

Biodegradable consumables on request.

Pos: 58 /Abkürzungen /Abkürzungen sprachneutr al/EasyC ut/EasyC ut F 360 C V @ 248\mod_1396591309890_0.docx @ 1932015 @ @ 1

EasyCut F 360 CV

Pos: 59 /BA/Wartung/T abellen_Füll meng en/Mähwer ke/T echnische D aten Betri ebsstoffe F üllmengen EC F 360 CV @ 381\mod_1444114418584_78.docx @ 2751590 @ @ 1

Specification

SAE 90

Specification Machine component Filling quantity

Input gearbox

Angular gearbox

1.7 l

0.9 l

Cutterbar 8.0 l

Biodegradable consumables on request.

Pos: 60 /Abkürzungen /Abkürzungen sprachneutr al/EasyC ut/EasyC ut F 360 CR @ 334\mod_1429276097173_0.docx @ 2550035 @ @ 1

EasyCut F 360 CR

Pos: 61 /BA/Wartung/T abellen_Füll meng en/Mähwer ke/T echnische D aten Betri ebsstoffe F üllmengen EC F 360 CR @ 381\mod_1444114779727_78.docx @ 2751691 @ @ 1

Machine component Filling quantity

Input gearbox

Angular gearbox

Upper roller gearbox

1.7 l

1.6 l

0.3 l

Pos: 62 /Ü berschriften/Überschriften 2/U-Z/U/U mgebungstemper atur @ 349\mod_1436336033553_78.docx @ 2624936 @ 2 @ 1

Cutterbar 8.0 l

Biodegradable consumables on request.

5.3 Ambient Temperature

Pos: 63 /BA/Einl eitung/T echnische D atenTechnische D aten: U mgebungstemper aturbereich @ 415\mod_1452855919473_78.docx @ 2914948 @ @ 1

Ambient temperature

Temperature range for machine operation

Pos: 64 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

SAE 90

Specification

SAE 90

-5 to +45°C

48

Pos: 65.1 /Überschriften/Überschriften 1/A-E/Erstinbetriebnahme @ 0\mod_1196314201498_78.docx @ 5855 @ 1 @ 1

Commissioning

6

Pos: 65.2 /Überschriften/Überschriften 2/P-T/SSpeziell e Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Commissioning

6.1 Special Safety Instructions

Pos: 65.3 /BA/Sicher heit/6. Ü ber arbeitete War nhi nweise/Warnung- Einstell arbeiten Maschi nen @ 297\mod_1412757509120_78.docx @ 2333197 @ @ 1

WARNING!

When performing repair, maintenance or cleaning work on the machine, or in case of technical intervention, drive elements may start moving.

Thus there is a risk of serious injuries or death.

• Switch off tractor engine, remove the ignition key and carry it with you.

• Secure the tractor against accidental start-up and against rolling.

• Wait until all machine parts have come to a complete stop and have been cooled down completely.

Pos: 65.4 /Überschriften/Überschriften 2/A-E/EErstmontag e @ 1\mod_1202226261982_78.docx @ 58270 @ 2 @ 1

6.2 First installation

Pos: 65.5 /BA/Sicher heit/7. Gefahrenhi nweise alt/Gefahr - Fehler hafter Zusammenbau @ 1\mod_1202224212591_78.docx @ 58171 @ @ 1

Danger! - Incorrect assembly

Effect: Danger to life, serious injuries or serious damage to the machine.

• Only authorised service centres may assemble the machine.

• The machine must be assembled with special care.

• Always heed the applicable accident prevention regulations.

• Use only safe and sufficiently dimensioned lifting equipment and load-securing equipment.

• The machine may be taken into operation only after all the safety devices have been installed.

• If unauthorised modifications are made to the machine, the manufacturer is released from liability for any resulting damage.

Pos: 65.6 /BA/Sicher heit/7. Gefahrenhi nweise alt/Gefahr - Fehlende Schutztücher Ersti nbetri ebnahme @ 3\mod_1204628072251_78.docx @ 71025 @ @ 1

Danger! - Missing guard cloths

Pos: 65.7 /BA/Ersti nbetriebnahme/Erstmontage @ 1\mod_1202224111998_78.docx @ 58190 @ @ 1

Pos: 65.8 /Überschriften/Überschriften 2/A-E/AAnpassung an den Tr aktor @ 101\mod_1330696961281_78.docx @ 899639 @ 2 @ 1

Effect: Lebensgefahr, schwere Verletzungen oder schwere Schäden an der Maschine.

• Before starting up the machine for the first time, install all supplied guard cloths on the machine.

The document "Assembly Instructions" describes how to install the device for the first time.

6.3 Adapting to the tractor

Pos: 65.9 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Warnung - Achsl asten Beei ntr ächtigung der Lenkfähig keit @ 9\mod_1220866555985_78.docx @ 128119 @ @ 1

Pos: 65.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Warning - Impairment of the steerability of the tractor.

Effect: Damage to the tractor or the machine.

The attachment of implements at the front and rear must not cause exceedance of the max. permissible weight, of the permissible axle loads and of the carrying capacities of the tractor tyres. Even with a fitted rear-mounted accessory unit, the front axle must always be loaded with a minimum 20% service weight of the tractor.

Make sure that these prerequisites are met prior to driving.

49

Commissioning

Pos: 65.11 /Ü berschriften/Ü berschriften 2/A-E/AAnbau an den Tr aktor @ 0\mod_1199717845194_78.docx @ 34039 @ 2 @ 1

6.4

Pos: 65.12 /Ü berschriften/Ü berschriften 3/K-O/KKuppelpunkte @ 9\mod_1220531326398_78.docx @ 126608 @ 3 @ 1

Mounting onto the Tractor

6.4.1 Clutching points

Pos: 65.13 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkte/Unterlenker @ 236\mod_1394446154303_78.docx @ 1871601 @ @ 1

Lower links

Pos: 65.14 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut geschoben @ 327\mod_1426080272248_78.docx @ 2506386 @ @ 1

EasyCut pushed

Pos: 65.15 /BA/Inbetri ebnahme/EasyCut/Vor ber eitung am Traktor Bild EC F 360 C V/CR geschoben @ 243 \mod_1395736145610_78.docx @ 1905942 @ @ 1

Kat.II

Kat.II

Kat.III

Pos: 65.16 /Abkürzungen /Abkürzung en Beschrei bung/EasyC ut gezogen @ 327\mod_1426080348028_78.docx @ 2506417 @ @ 1

Fig. 14

EasyCut trailed

Pos: 65.17 /BA/Inbetri ebnahme/EasyCut/Vor ber eitung am Traktor Bild EC F 360 C V/CR gezog en @ 244\mod_1395760597843_78.docx @ 1907909 @ @ 1

Kat.II

Kat.III

Kat.II

EC-484-0

Kat.III

Kat.III

Fig. 15

Pos: 65.18 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkteKuppel punkte Text EasyCut Kat II und III @ 373\mod_1442395123790_78.docx @ 2717919 @ @ 1

On EasyCut, the three-point linkage is designed for cat. II and III.

EasyCut is prepared as standard for category II.

• Slide ball sleeve cat. II (1) on lower link pin (2).

• Secure lower link pin by means of linch pin (4) and safety chain (5).

Refitting to category III:

• Pull out lower link pin (2), turn it by 180° and insert it.

The journal points outwards.

• Slide ball sleeve cat. II (3) onto lower link pin (2).

• Secure lower link pin by means of linch pin (4) and safety chain (5).

Pos: 65.19 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

50

EC-485-0

Pos: 65.20 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkte/Oberl enker @ 236\mod_1394445969901_78.docx @ 1871543 @ @ 1

Top link

Pos: 65.21 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkte/Kuppelpunkte Oberlenker Bild EC F 360 C V/CR @ 383\mod_1444369071911_78.docx @ 2756907 @ @ 1

Commissioning

EC00488-1

Fig. 16

Pos: 65.22 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkte/Auswahl Oberlenkerloch T ext EC B 360 CV/CR @ 244\mod_1395820161255_78.docx @ 1910403 @ @ 1

Depending on the length of the top link, the hole pattern for the top link in the three-point linkage must be selected.

Pos: 65.23 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkte/Kuppelpunkte T ext Oberlenker EC F 360 C V/CR Text @ 244\mod_1395818979649_78.docx @ 1910266 @ @ 1

• Insert top link bolt (1) into the hole pattern so that the roll pin (2) engages in the groove.

• Secure top link bolt (1) with spring cotter pin (3).

Pos: 65.24 /BA/Inbetri ebnahme/EasyCut/Achtung Abstand der M aschine zum Tr aktor zu geri ng @ 89\mod_1321957875595_78.docx @ 756771 @ @ 1

Caution! - The distance between the machine and the tractor is too small

Effect: damage to the tractor or the machine

Check free space for the front wheels at all steering angles. If the guards or swath flaps come into contact with the front wheels of the tractor, lower suspension arm adapters must be installed between the lower suspension arm and the Weiste triangle.

Pos: 65.25 /BA/Erstinbetriebnahme/EasyC ut/Kuppel punkte/Voraussetzung: Das M ähwer k ist am Traktor angebaut_Text EC B 360 C V/CR @ 386\mod_1444992488883_78.docx @ 2773208 @ @ 1

Pos: 65.26.1 /Ü berschriften/Ü berschriften 3/U-Z/U nterlenkeradapter @ 79\mod_1314688743340_78.docx @ 697532 @ 3 @ 1

Prerequisite:

The mower is attached to the three-point linkage of the tractor.

• Check whether the machine is aligned in lifted state parallel to the ground, refer to chapter

Start-up “Checking the Attachment”.

6.4.2 Lower suspension arm

Pos: 65.26.2 /BA/Inbetri ebnahme/EasyCut/U nterlenker adapter /Unterlenkeradapter Bild EC F 360 C V/CR @ 245\mod_1395831662445_78.docx @ 1911716 @ @ 1

5

2

3

1

4

EC-489-0

Fig. 17

Pos: 65.26.3 /BA/Inbetri ebnahme/EasyCut/U nterlenker adapter /Unterlenkeradapter fi xieren EC F- 360 C V/CR @ 245\mod_1395844223552_78.docx @ 1912755 @ @ 1 The lower link adapters (1) serve as extension to increase the distance from the machine to the front wheels of the tractor.

Pos: 65.26.4 /BA/Inbetri ebnahme/EasyCut/U nterlenker adapter /Unterlenkeradapter montier en Text @ 245\mod_1395844330614_78.docx @ 1912784 @ @ 1

Pos: 65.27 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Mounting lower link adapter

• Insert the lower link adapter (1) in the openings of the three-point linkage.

• Insert bolt (2) from the inside of the three-point linkage into the hole.

Make certain that the roll pin is located in the groove.

• Secure bolt (2) with disc (3) and linch pin (4).

• Screw lower link adapter (1) with disc, sleeve, detent edged washer and disc (5) on the three-point hitch.

51

Commissioning

Pos: 65.28 /Ü berschriften/Ü berschriften 2/F-J/GGel enkwelle @ 0\mod_1199781879794_78.docx @ 34542 @ 2 @ 1

6.5

Pos: 65.29 /BA/Sicherheit/Gel enkwell e/Gefahr - Sich drehende Gel enkwelle_2 @ 0\mod_1199781692950_78.docx @ 34523 @ @ 1

PTO shaft

Pos: 65.30 /BA/Sicherheit/Gel enkwell e/Gefahr - Antri ebsdr ehzahl 1000 beachten @ 3\mod_1204700292070_78.docx @ 71424 @ @ 1

Danger! - Rotating PTO shaft

Effect: Danger to life or serious injuries

• Install or detach the PTO shaft only with the engine switched off and the ignition key removed.

• Secure the tractor against rolling.

• Make sure that the PTO shaft is coupled properly (the lock of the PTO shaft must have snapped in).

• Make sure that the protective devices are attached properly.

• Never use a PTO shaft, the protective devices of which have not been attached.

• Replace damaged protective devices immediately

• Attach the safety chain of the PTO shaft so that the guard tube does not rotate simultaneously with the PTO shaft.

Pos: 65.31 /Ü berschriften/Ü berschriften 3/K-O/LLängenanpassung @ 1\mod_1201687632810_78.docx @ 53589 @ 3 @ 1

Danger! - Observe drive speed

Effect: Danger to life or serious injuries

• This machine is driven at a maximum PTO speed of 1000 rpm.

6.5.1 Length adjustment

Pos: 65.32 /BA/Erstinbetriebnahme/Gelenkwelle/M ähwer ke/Längenanpassung Gelenkwelle EC 32CVF @ 3\mod_1204701667336_78.docx @ 71443 @ @ 1

1

Pos: 65.33 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

2

AFA-0-006

Fig. 18

• Hold the two PTO shaft halves (1) and (2) next to each other

• Check the cover of the special section tubes and guard tubes

• Shorten special section tubes and guard tubes until they can move freely in any operating position

• For detailed information on adjusting the length, please refer to the operating instructions of the PTO shaft manufacturer

52

Pos: 65.34 /Ü berschriften/Ü berschriften 3/F-J/GGel enkwelle monti eren @ 11\mod_1223358863095_78.docx @ 145571 @ 3 @ 1

6.5.2 Install the PTO shaft

Pos: 65.35 /BA/Erstinbetriebnahme/EasyC ut/Vor bereitung am Fr ontschei benmäher EC F 360 CV/CR Bil d @ 243\mod_1395674164605_78.docx @ 1904763 @ @ 1

1 5

1

3

Commissioning

4

EC-482-0

Fig. 19

Pos: 65.36 /BA/Erstinbetriebnahme/EasyC ut/Vor bereitung am Fr ontschei benmäher EC F 360 CV/CR Text @ 243\mod_1395730369383_78.docx @ 1905545 @ @ 1

• Dismount covering hood (1).

• Slide on universal shaft (2) onto PTO shaft end of the front disc mower until the universal shaft protection is locked into place.

• Screw the pipe clamp (4) to prevent universal shaft guard (3) from turning.

• Put down universal shaft (2) on the universal shaft support (5).

• Mount covering hood (1).

Pos: 66 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

53

Start-up

Pos: 67.1 /Überschriften/Überschriften 1/F-J/Inbetri ebnahme @ 0\mod_1196327075811_78.docx @ 6375 @ 1 @ 1

7

Pos: 67.2 /Überschriften/Überschriften 2/U-Z/VVor bereitung en am Traktor @ 2\mod_1202363643678_78.docx @ 58694 @ 2 @ 1

Start-up

7.1 Preparations on tractor

Pos: 67.3 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - U nbeabsichtigtes Abkuppel n Fr ontmähwer ke @ 3\mod_1204641660735_78.docx @ 71218 @ @ 1

Danger! - Inadvertent uncoupling of the machine during road travel or work.

Effect: Danger to life, serious injuries or serious damage to the machine.

• Use extreme caution when attaching implements to or detaching them from the tractor! The accident prevention regulations must be complied with absolutely.

• When attaching or detaching the machine, do not walk between the tractor and the machine!

• The lower suspension arms of the front hydraulics on the tractor must be adjusted to swing freely. (see operating instructions for the front hydraulics)

• If the lower suspension arms on the tractor cannot be adjusted to swing freely, freeswinging lower suspension arm adapters must be installed.

• Lower suspension arm adapter order no. 140 190 (1x)

Pos: 67.4 /BA/Ersti nbetriebnahme/EasyC ut/Ersti nbetriebnahme M odulgruppen/Vorber eitungen am Tr aktor EC F 360 C V/CR @ 249 \mod_1396860923624_78.docx @ 1934719 @ @ 1

• Change front lifting unit to single-action.

• Disconnect lower links so that they can swing freely.

• Move front axle suspension to central position and deactivate it.

• Initial start-up has been made.

• Move tractor to assembling position.

• Connect lower links to the machine.

• Connect universal shaft to the tractor.

• Connect top link to the machine.

• Bring machine into transport position.

• Hinge relief springs as far to the outside as possible on top link clevis.

• Pull parking support upward until it engages.

Pos: 67.5 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

54

Pos: 67.6 /BA/Ersti nbetriebnahme/EasyC ut/Kuppelpunkte/Oberlenker @ 236\mod_1394445969901_78.docx @ 1871543 @ @ 1

Top link

Pos: 67.7 /BA/Ersti nbetriebnahme/EasyC ut/EasyC ut 32 C V Fl oat/WARNUN G - Oberlenkergabel falsch ang ebaut @ 180\mod_1376383491102_78.docx @ 1544935 @ @ 1

WARNING!

Start-up

If the top link fork has been fitted incorrectly, the threaded spindle may break and the machine may disconnect unintentionally and cause serious injuries.

When fitting the top link fork, make certain that the rounded off side (X) points upward and that the fork (3) below the straight side is attached onto the top link fork.

Pos: 67.8 /BA/Ersti nbetriebnahme/EasyC ut/F 360 C V/CR /Oberl enkergabel montier en Bil d F 360 CV/CR @ 244\mod_1395762840133_78.docx @ 1908701 @ @ 1

M30x3,5

2

1

3 x

3

EC-486-0

Fig. 20

Pos: 67.9 /BA/Ersti nbetriebnahme/EasyC ut/EasyC ut 32 C V Fl oat/Oberlenkergabel monti eren T ext @ 181\mod_1377006979231_78.docx @ 1553293 @ @ 1

Pos: 67.10 /Ü berschriften/Ü berschriften 2/F-J/GGel enkwelle monti eren @ 2\mod_1202398342788_78.docx @ 59253 @ 2 @ 1

• Screw the top link fork (1) (order no. 20 035 149 0) into the top link M 30 x 3,5 (2) (optional telescopic upper suspension arm).

• Attach the fork (3) below the straight side onto the top link fork.

• Install the top link fork with the rounded off side (X) to the top on tractor side.

• Make certain via visual inspection that the forks (3) point downward.

7.2 Install the PTO shaft

Pos: 67.11 /BA/Inbetri ebnahme/EasyCut/Anbau Gel enkwell e/Z wischeng elenkwell e/Anbau Gelenkwelle EC F 360 CV/CR @ 245\mod_1395928360507_78.docx @ 1915241 @ @ 1

2

1

Pos: 67.12 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

AFA-0-005

Fig. 21

• Slide universal shaft (1) onto PTO shaft end of the tractor and secure it.

• Secure universal shaft guard with retaining chain (2) against turning.

55

Start-up

Pos: 67.13 /Ü berschriften/Ü berschriften 2/A-E/AAnbau und Ei nstellung der Entlastungsfedern ÜS @ 89\mod_1321958243040_78.docx @ 756797 @ 2 @ 1

7.3

Pos: 67.14 /Ü berschriften/Ü berschriften 3/F-J/GGeschobene Ausführung @ 245\mod_1395916281296_78.docx @ 1914218 @ 3 @ 1

Mounting and Adjusting the Relief Springs

7.3.1 Pushed Design

Pos: 67.15 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Einstell ung der Entl astungsfeder n EC F 360 geschoben Bil d @ 245\mod_1395912760848_78.docx @ 1913825 @ @ 1

1

III

2

EC-516-0

Fig. 22

Pos: 67.16 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Di e Entlastungsfedern mä hwer kseitig einhängen EC F 360 CV Text @ 248\mod_1396512479701_78.docx @ 1929305 @ @ 1

• Hinge relief springs (1) on mowing unit side into the third hole (III) of the perforated bar (2).

Pos: 67.17 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau und Ei nstellung der Entlastungsfedern EC F 360 g eschoben Bild @ 245\mod_1395909859855_78.docx @ 1913618 @ @ 1

2

2

1

3

3

EC-487-0

Fig. 23 with tension jack

Pos: 67.18 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Einführungstext mi t/ohne Spannschloss EC F 360 @ 248 \mod_1396514148084_78.docx @ 1929909 @ @ 1 without tension jack

The relief springs can be hinged with tension jack (1) or without tension jack on the clevis of the top link (2).

A finer adjustment of the ground pressure is possible if the tension jack is used.

A coarser adjustment of the ground pressure is possible if the tension jack is not used.

Pos: 67.19 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

56

Pos: 67.20 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau mit Spanschl oss EC F 360 geschoben Bild @ 250 \mod_1396948815816_78.docx @ 1936768 @ @ 1

Start-up

5

2

4

1

3

EC-513-0

Fig. 24

Pos: 67.21 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau mit Spannschl oss EC F 360 geschoben T ext @ 244\mod_1395763346385_78.docx @ 1908838 @ @ 1

Fitting with tension jack

• Mount tension jack (1) with connecting link (3) on the clevis of top link (2).

• Hinge relief springs on both sides with the same length.

• Set the tension jack to a maximum value of a = 230 mm.

• Raise mowing unit, switch off tractor engine, remove the ignition key and carry it with you.

• Fasten the chain (4) as short as possible with connecting link (5) on the tension jack (1).

• Lower mowing unit into mowing position.

Pos: 67.22 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Ü berschüssige Kette abtrennen EC F 360 CV Text @ 245\mod_1395912585351_78.docx @ 1913766 @ @ 1

• Separate surplus chain and fasten it at a suitable point.

Pos: 67.23 /BA/Inbetri ebnahme/EasyCut/Hinweis Entlastungsfeder n einstell en 35° @ 245 \mod_1395914748947_78.docx @ 1914099 @ @ 1

Note

In mowing position, the inclination of the relief spring chain should be approx. 35° in mowing position.

Pos: 67.24 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau ohne Spanschloss EC F 360 geschoben Bil d @ 250\mod_1396949119980_78.docx @ 1936797 @ @ 1

2

4

3

EC-514-0

Fig. 25

Pos: 67.25 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau ohne Spannschloss EC F 360 geschoben T ext @ 248 \mod_1396514300230_78.docx @ 1929938 @ @ 1

Fitting without tension jack

• Raise mowing unit, switch off tractor engine, remove the ignition key and carry it with you.

• Fasten the chain (4) as short as possible with connecting link (3) on the tension jack clevis

(2).

• Lower mowing unit into mowing position.

Pos: 67.26 /BA/Inbetri ebnahme/EasyCut/Hinweis Entlastungsfeder n einstell en 35° @ 245 \mod_1395914748947_78.docx @ 1914099 @ @ 1

Pos: 67.27 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

In mowing position, the inclination of the relief spring chain should be approx. 35° in mowing position.

57

Start-up

Pos: 67.28 /Ü berschriften/Ü berschriften 2/F-J/FFedersicherungskette prüfen @ 252\mod_1397136427230_78.docx @ 1945436 @ 2 @ 1

7.4 Checking Spring Retaining Chain

Pos: 67.29 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/F edersicher ungskette EC F 360 geschoben Bild @ 248\mod_1396515215944_78.docx @ 1930026 @ @ 1

2 4

3

1

EC-515-0 EC-517-0

Fig. 26

Pos: 67.30 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/F edersicher ungskette EC F 360 geschoben T ext @ 383\mod_1444378546343_78.docx @ 2757164 @ @ 1

The spring safety chain (2) located in the relief spring (1) must be tensioned in the mowing position and must be visually inspected.

• Move the mower to working position.

• Check spring safety chain via visual inspection.

The spring safety chain is set so that it is a little loose, i. e. shows play.

If the spring safety chain is tensioned too tightly, i.e. does not show any play:

• Move mower to headland position.

• Hang retaining chain (3) by one link longer into the turnbuckle.

Repeat this process until the spring safety chain is no longer tensioned in working position.

Pos: 67.31 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

58

Pos: 67.32 /Ü berschriften/Ü berschriften 3/F-J/GGezogene Ausführung @ 245\mod_1395916618167_78.docx @ 1914247 @ 3 @ 1

7.4.1 Trailed Design

Pos: 67.33 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau und Ei nstellung der Entlastungsfedern EC F 360 g ezog en Bild @ 245\mod_1395916776026_78.docx @ 1914270 @ @ 1

1

Start-up

2

EC-491-0

Fig. 27

Pos: 67.34 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau EC F 360 gezogen T ext @ 248\mod_1396516596602_78.docx @ 1930203 @ @ 1

Mounting trailed machines

Pos: 67.35 /Ü berschriften/Ü berschriften 2/P-T/SSchutztuch spannen @ 248\mod_1396511342845_78.docx @ 1929282 @ 2 @ 1

• Move the mowing unit to working position.

• Set the cutting height, refer to Settings “Setting the Cutting Height”.

• Lower front hydraulics until the arrow head (1) points on centre link (2).

7.5 Tensioning Guard Cloth

Pos: 67.36 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Schutztuch spannen EC F 360 Bild @ 248\mod_1396507762276_78.docx @ 1928999 @ @ 1

1

EC-518-0

Fig. 28

Pos: 67.37 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Schtuztuch spannen EC F 360 CV Text @ 248\mod_1396507907275_78.docx @ 1929028 @ @ 1

• Every time before using the mower, tension the guard cloth (1) so that it cannot be caught by the CV roller.

Pos: 67.38 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

59

Start-up

Pos: 67.39 /Ü berschriften/Ü berschriften 2/A-E/BBel euchtung anschließ en @ 33\mod_1254385308979_78.docx @ 319105 @ 2 @ 1

7.6 Lighting connection

Pos: 67.40 /BA/Inbetri ebnahme/EasyCut/Bel euchtung/Anschluss Bel euchtung Bild EC F 360 C V/CR @ 245 \mod_1395923526865_78.docx @ 1914853 @ @ 1

1

2

3

EC-493-0

Fig. 29

Pos: 67.41 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @ @ 1

Pos: 67.42 /BA/Inbetri ebnahme/Schwader /Hinweis Sauber keit der Stecker und Steckdosen @ 2\mod_1202399563131_78.docx @ 59273 @ @ 1

Note

Before inserting the plugs, make certain the plugs and sockets are clean and dry. Dirt and moisture may result in short circuits!

Pos: 67.43 /BA/Inbetri ebnahme/Schwader /Anschluss Beleuchtung/Anschluss Beleuchtung Text @ 36 \mod_1260783798936_78.docx @ 336718 @ @ 1

The lighting system is connected via the 7-pin connection cable (1).

To do this:

• Insert the 7-pin plug of the connection cable (1) into the relevant socket (2) of the tractor.

• Insert the 7-pin connection cable plug (1) into the appropriate socket (3) of the machine.

• Position the cable so that it will not come in contact with the wheels.

Pos: 67.44 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

60

Pos: 67.45 /Ü berschriften/Ü berschriften 2/F-J/HH ydr auli k @ 0\mod_1199776034950_78.docx @ 34205 @ 2 @ 1

Start-up

7.7

Pos: 67.46 /Ü berschriften/Ü berschriften 3/P-T/SSpezi elle Sicher heitshi nweise @ 0\mod_1197301069931_78.docx @ 17662 @ 3 @ 1

Hydraulics

7.7.1 Special Safety Instructions

Pos: 67.47 /BA/Sicherheit/H ydr auli k/Warnung - Anschluss der H ydrauli klei tungen @ 0\mod_1199776548685_78.docx @ 34225 @ @ 1

Warning ! - Connection of the hydraulic line

Effect: severe injuries due to penetration of hydraulic oil under the skin.

• When connecting the hydraulic hoses to the hydraulic system of the tractor, the system must be relieved of the pressure on either side.

• Due to the risk of injury when searching for leaks, always use suitable tools and wear protective goggles.

• Seek medical help immediately should injuries occur! Danger of infection.

• Depressurise prior to uncoupling the hydraulic hoses and working on the hydraulic system!

• Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The replacement hoses must fulfil the technical requirements set by the equipment manufacturer.

Pos: 67.48 /Ü berschriften/Ü berschriften 3/F-J/HH ydr auli kl eitungen anschließ en @ 0\mod_1199777037794_78.docx @ 34244 @ 3 @ 1

7.7.2 Connecting the hydraulic lines

Pos: 67.49 /BA/Sicherheit/H ydr auli k/WARNUNG - Vertauschen der H ydrauli kkl eitungen, wenn EW @ 9\mod_1220871857985_78.docx @ 128182 @ @ 1

Warning - If the hydraulic hoses are interchanged when connecting them to the hydraulic system of the tractor, the functions will be interchanged as well.

Pos: 67.50 /BA/Sicherheit/H ydr auli k/Achtung - Verschmutzung der H ydrauli kanlag e @ 2\mod_1202393336803_78.docx @ 59155 @ @ 1

Effect: Injuries, serious damage to the machine

• Identify the hydraulic connections.

• Always ensure correct connection between the machine and the tractor.

• When engaging the hydraulic hose, the hydraulic control unit must be in float position or in

"lowering" position.

Caution! - Soiling of the hydraulic system

Effect: Damages to the machine

• When connecting the quick couplings, ensure that these are clean and dry.

• Note chafing areas or points of contact.

Pos: 67.51 /BA/Inbetri ebnahme/H ydrauli kkupplungen anschließ en all e Maschi nen/Hi nweis H ydrauli kanschluss BA Traktor @ 220\mod_1391434710718_78.docx @ 1782774 @ @ 1

Note

For further information about connecting the hydraulic lines, refer to the tractor operating instructions.

Pos: 67.52 /BA/Inbetri ebnahme/H ydrauli kkupplungen anschließ en all e Maschi nen/Hi nweis H ydrauli kaufkl eber an der M aschine beachten @ 204\mod_1386153225929_78.docx @ 1701911 @ @ 1

Pos: 67.53 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

Connect hydraulic hoses correctly.

• The hydraulic hoses are marked with numbers and coloured dust caps.

61

Start-up

Pos: 67.54 /BA/Inbetri ebnahme/EasyCut/H ydrauli k/H ydrauli kanschluss Bild EC F 280/320/360/ (M) @ 234\mod_1394086580639_78.docx @ 1864567 @ @ 1

EC-471-0

Fig. 30

Pos: 67.55 /BA/Inbetri ebnahme/H ydrauli kkupplungen anschließ en all e Maschi nen/H ydr auli kkuppl ung en anschließ en T eil1 @ 213\mod_1390207328923_78.docx @ 1749237 @ @ 1

• Set the single-action control units of the tractor to float position.

• Turn off the tractor and secure it against the possibility of rolling back.

Pos: 67.56.1 /BA/Bedienung /EasyC ut/Schutze/Bei Ausführung hydr aulischer Seitenschutz @ 332 \mod_1428387861893_78.docx @ 2536837 @ @ 1

With hydraulic side guards design

Pos: 67.56.2 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung Quetschgefahr/Senken von Seitenschutz @ 331\mod_1427802696458_78.docx @ 2532405 @ @ 1

WARNING!

Crushing hazard when lowering the side guards

While lowering the hydraulic side guards, there is a danger of being crushed between side guard and upper protective cover.

• While lowering the side guards, make sure that there is no one in the danger zone .

Pos: 67.56.3 /BA/Bedienung /EasyC ut/Schutze/Absenken hydr aulischer Seitenschutz_T ext @ 332 \mod_1428387391162_78.docx @ 2536775 @ @ 1

Pos: 67.57 /BA/Inbetri ebnahme/EasyCut/Probel auf nach Erstmontag e @ 3\mod_1205215927275_78.docx @ 73555 @ 2 @ 1

• Fold down the side guards by means of double-action control unit (red1/blue1) of the tractor.

7.8 Trial run after first installation

Pos: 67.58 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Caution!

After the first connection to the tractor, the machine must undergo a trial run.

• The machine must be in working position

• Do not switch on the PTO until the machine is resting on the ground and you are absolutely sure that there are no persons, animals or objects in the danger zone.

• Start a trial run of the machine from the driver’s seat of the tractor only.

• Lower the machine into working position.

• Carefully switch in the PTO of the tractor.

• Slowly increase the PTO speed to 1000 rpm.

• Check that the machine is running smoothly and without vibrations.

• Reduce the PTO speed to idling and wait for the cutting discs / mower drums to come to a stansdstill.

• Raise or lower the machine via the tractor hydraulics.

62

Pos: 67.59 /Ü berschriften/Ü berschriften 2/U-Z/UÜ berpr üfung des Anbaues @ 250\mod_1396950419168_78.docx @ 1936882 @ 2 @ 1

Start-up

7.9 Checking Fitting

Pos: 67.60 /BA/Inbetri ebnahme/EasyCut/Ü ber prüfung des Erstanbaues Achtung EC F 280(M) / F 320(M) / F 360(M) @ 204\mod_1386142598536_78.docx @ 1701547 @ @ 1

CAUTION!

Machine or tractor may be damaged if the machine is connected incorrectly.

If the universal shaft is bent unfavourably, the machine runs irregularly and machine or tractor may be damaged seriously.

• To prevent damages, the machine must be aligned in parallel to the ground in the raised condition.

Pos: 67.61 /BA/Inbetri ebnahme/EasyCut/Ü ber prüfung des Erstanbaues Bild EC F 280(M) / F 320(M) / F 360(M) @ 205\mod_1386257293841_78.docx @ 1707146 @ @ 1

EC-460-0

Fig. 31

Pos: 67.62 /BA/Inbetri ebnahme/EasyCut/Ü ber prüfung des Erstanbaues Beschrei bung EC F 280(M) / F 320(M) / F 360(M) @ 205\mod_1386319363029_78.docx @ 1707967 @ @ 1 Mount top link on the A-frame (Weiste triangle) or on the upper coupling point of the machine so that the machine is aligned as parallel as possible to the ground in the raised condition.

To do this:

• Raise the machine.

• Switch off tractor, secure the tractor from rolling away and remove the ignition key.

• Check the parallelism of the machine to the ground.

If the parallelism is OK, connecting can be continued.

If the parallelism deviates too strong:

• Lower machine to the ground.

• Switch off tractor, secure the tractor from rolling away and remove the ignition key.

• Move top link in the hole pattern on the A-frame (Weiste triangle).

• Raise the machine and check parallelism.

Repeat this process until the machine raises in parallel to the ground.

Pos: 68 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

63

Driving and Transport

Pos: 69.1 /Überschriften/Überschriften 1/F-J/F ahr en und Transport @ 0\mod_1196330049217_78.docx @ 6553 @ 1 @ 1

8 Driving and Transport

Pos: 69.2 /BA/Sicher heit/Fahren und Transport/Mitfahr en Straß enfahrt/Gefahr Straß enfahrt, Mitfahren EasyCut Front @ 3\mod_1204784303933_78.docx @ 72994 @ @ 1

Danger! - Transport / road travel

Effect: Danger to life, serious injuries or serious damage to the machine.

• Before swivelling the machine up into transport position, switch off the PTO.

• Wait until machine stops

• When travelling on public roads, observe the applicable current regulations (lighting, identification, axle loads, permitted front end dimension, etc.)!

• When being transported on public roads, the mowing unit must be lifted.

• It is forbidden to carry passengers on the machine.

• Before starting, ensure that you have perfect visibility on and around the tractor and the machine.

Pos: 69.3 /BA/Sicher heit/Fahren und Transport/Absperrhahn/Transport / Str aßenfahr t Absperr hahn in Fronthydraulik Traktorseitig schließ en @ 33\mod_1254118215456_78.docx @ 318342 @ @ 1

DANGER! - Transport / road travel

Effect: Danger to life, serious injuries or serious damage to the machine.

• A shut-off valve must be existent in the hydraulic line for the front hydraulic of the tractor.

• The shut-off valve must always be locked during transport / road travel.

Pos: 69.4 /BA/Sicher heit/Fahren und Transport/Absperrhahn/War nung -Transport / Straß enfahrt Absperr hähne schli eßen @ 313\mod_1421221173942_78.docx @ 2417858 @ @ 1

WARNING! - Transport / road travel

Risk of accident due to non-locked stop cocks.

Machine components can be activated unintentionally when the stop cocks are not locked during transport travel. This may result in serious accidents.

• To prevent functions from being triggered accidentally, always close the hydraulic stop cocks in the transport position.

Pos: 69.5 /Überschriften/Überschriften 2/A-E/BBeleuchtung @ 0\mod_1195658399935_78.docx @ 1881 @ 2 @ 1

8.1 Lighting

Pos: 69.6 /BA/Sicher heit/Fahren und Transport/Beleuchtung/Bel euchtungsanlag e alle M aschinen @ 7 \mod_1215519058839_78.docx @ 103206 @ @ 1

Pos: 69.7 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - Lighting system

Effect: Danger to life, serious injuries or serious damage to the machine.

• Before transporting on public roads, always connect the lighting system and perform a function check.

• Keep the lighting system clean. Soiled lights and spotlights impair road safety.

• Replace defective light bulbs or broken spotlights.

• When transporting on public highways, the machine must be in the transport position.

64

Pos: 69.8 /BA/F ahren und Tr ansport/EasyCut/Vor baumaß Länderabhängig EC _Front @ 3\mod_1204784822668_78.docx @ 73052 @ @ 1

A 3,5 m

Driving and Transport

EC-224-0

Fig. 32

Note - Depending on the country

If the front end dimension "A" exceeds 3.5 m, provide suitable means (e.g. assistant giving instructions or mirror at road junctions) to ensure road safety (data sheet for attached implements supplied by the Federal Minister for Transport).

Pos: 69.9 /BA/F ahren und Tr ansport/EasyCut/Schutze i n Tr ansportstellung bringen EC F 320 CV / F 360 CV/CR @ 332\mod_1428655376555_78.docx @ 2541007 @ @ 1

1 1

EC-533-0

Fig. 33

Move the guard cloths (1) right and left to transport position before road travel. Open lateral guards by using a pointed object (for example blade key / screw driver).

• Press the ratchet down with a pointed object, fold up guard and allow it to engage in the locking device

Pos: 69.10 /BA/Bedienung /EasyC ut/Schutze/Schutze i n Transpor tstellung bring en / hydraulische Außenschutze EC F 320 CV @ 236\mod_1394440249507_78.docx @ 1870638 @ @ 1

Pos: 69.11 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

With hydraulic outer guards design

• Fold up the outer guards of the tractor by using the double-action control unit (red1/blue1).

65

Driving and Transport

Pos: 69.12 /BA/F ahr en und Transpor t/EasyC ut/Feststeller und Schnäpper @ 78\mod_1314002912379_78.docx @ 694482 @ 2 @ 1

8.2 Clamp and Buffer

1

Pos: 70 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-385-0

Fig. 34

Check the clamp and buffer (1) for tight fit every time before transport or road travel.

If the clamp and buffer show signs of damage or wear, replace them.

Item No.: 00 250 831 1

66

Pos: 72 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Driving and Transport

67

Operation

Pos: 73.1 /Überschriften/Überschriften 1/A-E/Bedienung @ 0\mod_1199789505403_78.docx @ 34825 @ 1 @ 1

9

Pos: 73.2 /Überschriften/Überschriften 2/U-Z/VVor dem M äheinsatz @ 3\mod_1204788384465_78.docx @ 73168 @ 2 @ 1

Operation

9.1 Before mowing

Pos: 73.3 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Warnung - Uner wartete Bewegung der Schneidwer kzeug e bzw. des M ähwer kes @ 299\mod_1412937148121_78.docx @ 2341087 @ @ 1

WARNING!

Foreign bodies may be hurled up during the operation.

Thus there is a risk for persons staying in the danger zone to be seriously hurt or killed.

Therefore the following points must be observed before the machine is used:

• The mower must be in working position.

• Move protective equipment into protective position and make sure that it is not damaged.

Pos: 73.4 /BA/Bedi enung /EasyC ut/Mähen/Hi nweis Bei m M ähen Frontmähwer ke @ 33\mod_1254117934018_78.docx @ 318312 @ @ 1

• Replace damaged protective equipment immediately.

• Instruct persons to leave the danger zone.

• Special care should be taken when working near roads and buildings.

• Make sure each time before the mower is used that blades, retaining bolts, leaf springs and cutting discs or mower drums are not damaged, worn or missing; replace them, if necessary!

Note while mowing

Effect: Proper use of the machine

• Change the front power lift to single-acting (only lifting, no pressing). The lowering of the mowing unit results from the dead weight of the mowing unit. The mowing unit must not be additionally loaded over the front power lift.

• During work the hydraulic control lever for the front power lift must be set to “

Float position

“.

Pos: 73.5 /BA/Bedi enung /EasyC ut/Mähen/Absperrhahn für di e Fronthydrauli k des Traktors lösen. @ 33\mod_1254119058096_78.docx @ 318361 @ @ 1

• Open the shut-off valve for the front hydraulic of the tractor.

Pos: 73.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

68

Pos: 73.7 /BA/Bedi enung /EasyC ut/SchutzeSchutztuch spannen EC F 360 C V/CR @ 245\mod_1395934767761_78.docx @ 1915511 @ 2 @ 1

9.2 Tensioning Guard Cloth

Operation

EC-495-0

Fig. 35

Every time before using the mower, the guard cloth (1) must be tensioned so that it cannot be caught by the CV roller.

Pos: 73.8 /Überschriften/Überschriften 2/P-T/SSchutze i n Arbeitsstellung bringen @ 35\mod_1257499551281_78.docx @ 329310 @ 2 @ 1

9.3 Moving the guards into the working position

Pos: 73.9 /BA/Bedi enung /EasyC ut/Schutze/Schutze i n Arbeitsstell ung bringen EC F 360 CV/CR @ 245\mod_1395934916074_78.docx @ 1915540 @ @ 1

1 1

2

EC-496-0

Fig. 36

Move guard (1) right and left to working position before every use.

• Loosen locking (2).

• Fold down guard.

Pos: 73.10.1 /BA/Bedienung /EasyC ut/Schutze/Bei Ausführung hydr aulischer Seitenschutz @ 332 \mod_1428387861893_78.docx @ 2536837 @ @ 1

With hydraulic side guards design

Pos: 73.10.2 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung Quetschgefahr/Senken von Seitenschutz @ 331\mod_1427802696458_78.docx @ 2532405 @ @ 1

WARNING!

EC-428-0

Crushing hazard when lowering the side guards

While lowering the hydraulic side guards, there is a danger of being crushed between side guard and upper protective cover.

• While lowering the side guards, make sure that there is no one in the danger zone .

Pos: 73.10.3 /BA/Bedienung /EasyC ut/Schutze/Absenken hydr aulischer Seitenschutz_T ext @ 332\mod_1428387391162_78.docx @ 2536775 @ @ 1

• Fold down the side guards by means of double-action control unit (red1/blue1) of the tractor.

Pos: 73.11 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

69

Operation

Pos: 73.12 /Ü berschriften/Ü berschriften 2/P-T/SSchutze in Transportstell ung bring en EC F 320 C V @ 236\mod_1394440817790_78.docx @ 1870726 @ 2 @ 1

9.4 Moving Guards into Transport Position

Pos: 73.13 /BA/Bedienung /EasyC ut/Schutze/Schutze i n Transpor tstellung bring en / hydraulische Außenschutze EC F 320 CV @ 236\mod_1394440249507_78.docx @ 1870638 @ @ 1

Pos: 73.14 /Ü berschriften/Ü berschriften 2/A-E/AAbstellstütze @ 17\mod_1236317851151_78.docx @ 204315 @ 2 @ 1

With hydraulic outer guards design

• Fold up the outer guards of the tractor by using the double-action control unit (red1/blue1).

9.5 Parking support

Pos: 73.15 /BA/Bedienung /EasyC ut/Abstellstütze/Achtung Abstellstütze muss ei ngeschoben sein @ 72\mod_1307513370887_78.docx @ 651311 @ @ 1

Caution! -Parking support not pushed in!

Effect: Damage to the machine

• Make certain before road/transport travel and for work that the parking support is pushed in and secured

Pos: 73.16 /BA/Bedienung /EasyC ut/Abstellstütze/Abstellstütze ein- / ausg eklappt Bild EC F 360 CV/CR @ 245\mod_1395935991145_78.docx @ 1915631 @ @ 1

2

1

2

1

Fig. 37

Pos: 73.17 /BA/Bedienung /EasyC ut/Abstellstütze/Abstellstütze einschi eben / herunterlassen ausgekl appt Text EC F 320 CV/360 CV/CR @ 235\mod_1394435243810_78.docx @ 1870255 @ @ 1

• Raise the machine via tractor hydraulics.

• Switch off tractor engine, remove the ignition key and carry it with you.

Lowering the parking support

• Pull bolt (1), lower parking support (2) and secure with bolt (1).

• Lower machine via tractor hydraulics.

Pushing in the parking support

• Pull bolt (1), push in parking support (2) and secure with bolt (1).

Pos: 73.18 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-497-0

70

Pos: 73.19 /Ü berschriften/Ü berschriften 2/A-E/AAbbau der Maschi ne @ 3\mod_1204792387824_78.docx @ 73245 @ 2 @ 1

Operation

9.6 Detaching the machine

Pos: 73.20 /BA/Sicherheit/EasyCut/Gefahr - M aschine abstell en_ohne H ydrauli kschlauch @ 3\mod_1204793072152_78.docx @ 73283 @ @ 1

Danger! - Unexpected movements of the machine

Pos: 73.21 /Ü berschriften/Ü berschriften 2/F-J/HHalteketten demontier en @ 240\mod_1395128934085_78.docx @ 1889511 @ 2 @ 1

Effect: Danger to life, serious injuries

• No one is permitted inside the danger zone.

• Park the machine on a solid and even surface.

• You should not unhitch the machine until the engine has been switched off and the ignition key has been removed.

• Secure the tractor against rolling.

• Use extreme caution when attaching implements to or detaching them from the tractor! The accident prevention regulations must be complied with absolutely.

• When detaching the machine, do not walk between the tractor and the machine!

9.7 Dismounting Retaining Chains

Pos: 73.22 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Ei nstellung an den Hal teketten @ 4\mod_1211349830489_78.docx @ 83185 @ @ 1

Danger! - Adjustment on the retaining chains

Effect: Danger to life or serious injuries

• The retaining chains may be removed in transport position only. In the working position the retaining chains are subject to high tensile stress.

Pos: 73.23 /BA/Bedienung /EasyC ut/Abbau EC F 320 C V / F360 C V/CR @ 332\mod_1428589668168_78.docx @ 2540608 @ @ 1

• Severe injury may occur if the retaining chains are removed while in the working position.

4 1

3

2

6

7

8

5

Pos: 74 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-498-1

Fig. 38

• Move front mounted mower into transport position.

• Lower parking support.

• Remove supporting chain (1) from the tractor.

• Lower front mounted mower.

• Remove lighting cable on tractor side and put it down on the machine.

• With hydraulically folding side guards design: Disconnect hydraulic hoses on tractor side.

• Remove top link (2) on machine side and fasten it in the support (3) on the tractor.

• Loosen guard cloth (4) on both sides.

• Remove supporting chain (5) of universal shaft on tractor side.

• Remove universal shaft (6) on tractor side and put it down on universal shaft bracket (7).

• Carefully lower front hydraulics (8).

• Carefully move out of the holder.

71

Settings

Pos: 75.1 /Überschriften/Überschriften 1/A-E/Ei nstellungen @ 0\mod_1199868783862_78.docx @ 36141 @ 1 @ 1

10 Settings

Pos: 75.2 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - R epar atur _Wartung_R einigungs_3 @ 0\mod_1196660613260_78.docx @ 9153 @ @ 1

Danger! - When performing repair, maintenance or cleaning work on the machine , or in the case of technical intervention, drive elements may start moving.

Effect: Danger to life, injuries or damage to the machine.

• Switch off the engine and remove the ignition key.

• Secure the machine against accidental start-up and against rolling!

• The cutter blades can continue to rotate after the drive has been switched off. Only approach the machine once the work tools have come to a complete standstill!

• After completing maintenance work reattach all safety devices properly.

• Avoid skin contact with oil and grease.

• Seek medical help immediately should injuries caused by oil escaping under pressure occur.

Pos: 75.3 /Überschriften/Überschriften 2/A-E/EEinstell ung der Entl astungsfedern ( 2015-10-19 15:05:29) @ 0\mod_1196666659447_78.docx @ 10133 @ 2 @ 1

10.1 Adjusting the Compensation Springs

Pos: 75.4 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Einstell ung an den Entlastungsfedern @ 0\mod_1196751594562_78.docx @ 12575 @ @ 1

Danger! - Setting on the compensation springs

Effect: Danger to life or serious injuries

• The compensation springs must only be removed in transport position. In the working position the compensation springs are subject to high tensile stress.

• Severe injury can be caused if the compensation springs are removed while in the working position.

• The lower threaded blocks on the compensation springs must be fully screwed in.

Pos: 75.5 /BA/Einstell ung en/Mähwer ke/EasyC ut/Bodendruck/Bodendruck allgemeiner T ext all e EC @ 0\mod_1196667271181_78.docx @ 10190 @ @ 1

The ground pressure for the cutter bar is adjusted to local conditions by means of the compensation springs. In order to protect the sward the load on the mowing spar must be relieved so that it does not jump when mowing, yet does not leave any skid marks on the ground.

Pos: 75.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

72

Pos: 75.7 /Überschriften/Überschriften 2/A-E/E/Ei nstellung der Schutze @ 3\mod_1204709091570_78.docx @ 71854 @ 2 @ 1

Settings

10.2 Adjusting the Guards

Pos: 75.8 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - F ortschleuder n von Stei nen @ 84\mod_1318311844997_78.docx @ 733435 @ @ 1

DANGER! – Stones forcibly projected during operation

Effect: Danger to life or serious injuries.

• Check the guard cloths regularly. Worn or damaged guard cloths must be replaced!

• The protective equipment on the mowing unit, e.g. cloths and hoods, protects against flying stones and similar objects, and also prevents access to dangerous parts. Because of this, you must always move it to its protective position before starting work

• Fold the side plate(s) down and secure with twist locks before use

Pos: 75.9 /BA/Einstell ung en/Mähwer ke/Z etter drehzahl/Seitliche Schutze neue Generation EC F 320C V/360C V/CR Bild_T ext @ 383\mod_1444384878210_78.docx @ 2757371 @ @ 1

The safety device can be adapted to harvesting conditions by adjusting the inclination.

• In order to avoid that crops are kinked because the guards are too low, set the guards higher.

• To avoid that stones or the like are ejected when the crops are low, set the guards lower.

Pos: 75.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 39

• Fold up guards (1) and guard (2).

• Unscrew the screws (4).

• Use mounting bar (3) to set the height of the guards.

• Tighten the screws (4).

• Fold down guards (1) and guard (2).

73

Settings

Pos: 75.11 /Ü berschriften/Ü berschriften 3/F-J/GGeschobene Ausführung @ 245\mod_1395916281296_78.docx @ 1914218 @ 3 @ 1

10.2.1 Pushed Design

Pos: 75.12 /Ü berschriften/Ü berschriften 4/A-E/Bei Anbau mit Spannschloss @ 332\mod_1428906332613_78.docx @ 2541465 @ @ 1

When mounted with turnbuckle

5 2

VI

I V

I I

V

I I I

I

4 1 3

EC-534-0

Fig. 40

The ground pressure of the mower can be set via bore holes (I) to (VI) of perforated bar or via the length of the supporting chains (4).

Perforated bar:

I = high mower relief = low ground pressure

VI = low mower relief = high ground pressure

Supporting chain:

Hinged short = high mower relief = low ground pressure

Hinged long = low mower relief = high ground pressure

Pos: 75.14 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Setting the ground pressure:

• Turn off PTO shaft.

• Lift mower via front hydraulics of tractor.

• Switch off tractor engine, remove ignition key and carry it with you.

Via perforated bar

• Hang relief springs into one of the bore holes (I) to (IV) in the perforated bar.

Via supporting chain

• Hinge supporting chain (4) into the chain link (5) shorter or longer.

Note

If the supporting chain cannot be set so that it is shorter in the chain link and the ground pressure is still too high, the distance to the tractor can be increased by means of lower suspension arm adapters. As a result, an extended setting of the supporting chain is possible.

74

Pos: 75.15 /Ü berschriften/Ü berschriften 3/F-J/GGezogene Ausführung @ 245\mod_1395916618167_78.docx @ 1914247 @ 3 @ 1

10.2.2 Trailed Design

Pos: 75.16 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Entlastungsfedern ei nstellen EC F 320 CV / EC F 360 CV/CR gezogen @ 333\mod_1429014682648_78.docx @ 2543289 @ @ 1

1

Pos: 75.17 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 41

Set the ground pressure of the mower by using the threaded spindle (1).

Turn threaded spindle clockwise = high mower relief = low ground pressure

Turn threaded spindle anti-clockwise = low mower relief = high ground pressure

Setting the ground pressure:

• Turn off PTO shaft.

• Lower mower via front hydraulics of tractor into working position.

• Switch off tractor engine, remove ignition key and carry it with you.

Reducing ground pressure

• Turn threaded spindle (1) clockwise.

Increasing ground pressure

• Turn threaded spindle (1) anti-clockwise.

Settings

75

Settings

Pos: 75.18 /Ü berschriften/Ü berschriften 2/A-E/EEinstellen der Schnitthöhe @ 0\mod_1196660879619_78.docx @ 9191 @ 2 @ 1

10.3 Adjusting the cutting height

Pos: 75.19 /BA/Ei nstellungen/M ähwer ke/Schnitthöhe/Schni tthöhe Bil d EC 28/32 C V @ 3\mod_1204708273867_78.docx @ 71808 @ @ 1

EC-083-2

Fig. 42

Pos: 75.20 /BA/Ei nstellungen/M ähwer ke/Schnitthöhe/Schni tthöhe größer _gering er @ 0\mod_1196661562478_78.docx @ 9269 @ @ 1

The cutting height is adjusted via the top link (1).

To do this:

• Lower the front mowing unit into working position

• Rotate the top suspension arm (1)

Top suspension arm longer = smaller cutting height

Top suspension arm shorter = bigger cutting height

Pos: 75.21 /BA/Ei nstellungen/M ähwer ke/T eleskopoberlenker @ 3\mod_1204708776180_78.docx @ 71835 @ 3 @ 1

10.3.1 Telescopic upper suspension arm

1

3

2

Pos: 75.22 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

AFA-0-020

Fig. 43:

In order to allow the front-mounted disc mower to adapt to the ground in the direction of travel, a telescopic upper suspension arm can be purchased as optional additional equipment. Via the telescopic upper suspension arm, the cutting height is set by loosening the counter nut (2) and

(3). By moving the lockclip (1), the compression spring of the telescopic upper suspension arm is released. This guarantees optimum adaptation of the front mowing unit in the direction of travel.

76

Pos: 75.23 /Ü berschriften/Ü berschriften 2/A-E/AAufbereiterdr ehzahl einstell en @ 248\mod_1396526275767_78.docx @ 1930518 @ 2 @ 1

Settings

10.4 Setting Conditioner Speed

Pos: 75.24 /Abkürzungen /C V-Ausführung @ 95\mod_1328530180147_78.docx @ 799128 @ @ 1

CV-Design

Pos: 75.25 /BA/Sicherheit/7. Gefahr enhinweise alt/Einstell arbeiten / Einstell ungen/Gefahr - Einstell ung en an der Maschi ne @ 0\mod_1196668628056_78.docx @ 10285 @ @ 1

Danger! - Settings on the machine

Effect: Danger to life, injuries or damage to the machine.

• Setting tasks must only be performed when the drive is switched off and the engine is at a standstill! Remove the ignition key!

Pos: 75.26 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Aufbereiterdr ehzahl einstell en Riemenscheiben EC F 360 CV/CR Bil d/T ext @ 245\mod_1396003473212_78.docx @ 1916562 @ @ 1

1

Pos: 75.27 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

2

EC-507-0

Fig. 44

Two conditioner speeds can be set on the belt drive. This affects conditioning effect and power consumption.

Maximum speed: 900 rpm (large pulley (1) top, small pulley (2) bottom).

Minimum speed: 600 rpm (small pulley (2) top, large pulley (1) bottom).

77

Settings

Pos: 75.28 /Ü berschriften/Ü berschriften 3/P-T/RRiemenschei be wechseln @ 328\mod_1426683455177_78.docx @ 2514613 @ 3 @ 1

10.4.1 Changing Pulley

Pos: 75.29 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/WARNUN G! – Verletzungsgefahr durch unter F ederspannung stehende Bauteile! @ 252\mod_1397140836170_78.docx @ 1946524 @ @ 1

WARNING!

When tensioning and releasing, the blade key is under spring tension. If the blade key is released too early, then it will spring back.

This may result in injuries.

• Do not release the blade key when tensioning and releasing.

Pos: 75.30 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Ri emenschibe wechsel n EC F 360 CV/CR Bild @ 245\mod_1396007294829_78.docx @ 1916739 @ @ 1

1

3

5

8

7

2

4

7

8

6

EC-520-0

Fig. 45

Pos: 75.31 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Ri emenschibe wechsel n EC F 360 CV/CR T ext @ 245\mod_1396004944381_78.docx @ 1916621 @ @ 1

• Unlock the drive guard on the locking screw (1) and remove it.

• Pull out linch pin (2).

• To release the belt drive, insert the blade key (3) in the tensioning device (4) and pull it to the rear.

• Remove V-belt.

• To pull the pulleys (5) and (6) from the shaft, remove linch pin (7) and discs (8).

Pos: 75.32 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

78

Pos: 75.33 /Ü berschriften/Ü berschriften 3/P-T/RRiemenschei be tauschen @ 328\mod_1426689351744_78.docx @ 2515676 @ 2 @ 1

Settings

10.4.2 Replacing Pulley

Pos: 75.34 /BA/Sicherheit/7. Gefahr enhinweise alt/Einstell arbeiten / Einstell ungen/Gefahr - Einstell ung en an der Maschi ne @ 0\mod_1196668628056_78.docx @ 10285 @ @ 1

Danger! - Settings on the machine

Effect: Danger to life, injuries or damage to the machine.

• Setting tasks must only be performed when the drive is switched off and the engine is at a standstill! Remove the ignition key!

Pos: 75.35 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/M ontag e der Keilriemenschei ben EC F 360 CV/CR Bild @ 248\mod_1396527267816_78.docx @ 1930547 @ @ 1

1

3 5

4

6

2

7

3

8

4

EC-519-0

Fig. 46

Pos: 75.36 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/M ontag e der Keilriemenschei ben EC F 360 CV/CR T ext @ 245\mod_1396009090393_78.docx @ 1916768 @ @ 1

• Push pulleys (1) onto the shaft top and bottom.

Make certain the pulleys are flush with each other.

• Secure pulley with disc (3) and linch pin (4).

• Pull V-belts (5) onto the V-belt pulleys.

• To tension the belt drive, insert blade key (6) into the tensioning device (7) and push it to the front until it engages.

Pos: 75.37 /Ü berschriften/Ü berschriften 3/P-T/RRiemenantri eb spannen @ 328\mod_1426686085413_78.docx @ 2514945 @ 3 @ 1

• Secure tensioning device with linch pin (8).

10.4.3 Tensioning Belt Drive

Pos: 75.38 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Ri ementrieb spannen EC F 360 C V/CR Bild @ 248 \mod_1396531120669_78.docx @ 1930925 @ @ 1

4

8

5

2

3

1

6

7

EC-521-0

Fig. 47

Pos: 75.39 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Spannen des Riementiebes EC F 360 C V/CR T ext @ 248\mod_1396531113982_78.docx @ 1930716 @ @ 1

When tensioning the V-belts, make certain that the adjustment aid (1) is flush with the upper edge of the tension spring (2).

• Loosen nuts (3) if the adjustment aid is not flush.

• Tension with threaded rod (4), tension spring (2) and lock with nuts (3) so that the adjustment aid is flush with the upper edge of the spring.

• Mount V-belt guard (8).

Pos: 75.40 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

79

Settings

Pos: 75.41 /Ü berschriften/Ü berschriften 2/A-E/EEinstellen des Aufberei tungsbl echs @ 0\mod_1196670615681_78.docx @ 10399 @ 2 @ 1

10.5 Adjusting the conditioner plate

Pos: 75.42 /Abkürzungen /C V-Ausführung @ 95\mod_1328530180147_78.docx @ 799128 @ @ 1

CV-Design

Pos: 75.43 /BA/Ei nstellungen/M ähwer ke/EasyCut/Ei nstellung des Aufber eitungsbleches Bild 360 CV/C R @ 245\mod_1395989855917_78.docx @ 1915844 @ @ 1

Fig. 48

Pos: 75.44 /BA/Ei nstellungen/M ähwer ke/Einstell ung des Aufbereitungsbleches T ext EC280/320 C V-Q -1 @ 59\mod_1297429715286_78.docx @ 558136 @ @ 1

The degree of conditioning is changed by adjusting the lever (1).

In the “+” direction: Degree of conditioning is increased

In the “-” direction: Degree of conditioning is decreased

Always check the tedder for damaged tines before the machine is used:

Straighten any bent tines.

Replace any broken tines.

Pos: 75.45 /Ü berschriften/Ü berschriften 3/A-E/E/Einstell ung bei Schwadablage @ 3\mod_1204713732476_78.docx @ 72183 @ 3 @ 1

10.5.1 Adjustment for Swathing

Pos: 75.46 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Einstell ung der Schwadablage EC F 360 C V/CR Bild/Text @ 250\mod_1396958850805_78.docx @ 1937660 @ @ 1

2

Pos: 75.47 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

1

1

EC-500-0

Fig. 49

The swath width is set by swath flaps at the rear side of the machine. The swath flaps are locked by ring nuts (2).

80

Pos: 75.48 /Ü berschriften/Ü berschriften 3/A-E/B/Breitablage @ 3\mod_1204713764351_78.docx @ 72202 @ 3 @ 1

10.5.2 Wide spreading

Pos: 75.49 /Abkürzungen /Abkürzung en Beschrei bung/Opti onal @ 102\mod_1331109267412_78.docx @ 902782 @ @ 1 optional

Pos: 75.50 /BA/Ei nstellungen/M ähwer ke/Schwadbr eite / Brei tablag eEi nstellung Br eitabl age EC F 320 CV Teil 1 ( Bild) @ 296\mod_1412602524182_78.docx @ 2323792 @ @ 1

Settings

EC-434-0_1

Fig. 50

Pos: 75.51 /BA/Ei nstellungen/M ähwer ke/Schwadbr eite / Brei tablag e/Einstellung Breitabl age EC F 320 C V T eil 2 (Text) @ 296 \mod_1412659281632_78.docx @ 2324735 @ @ 1

• Mount deflector sheets (2) with coach screw (3), plastic disc (4), disc (5) and tristar knob (6) as well as coach screw (7) (short square), disc (8) and locknut (9).

Set the deflector sheets according to the operating conditions in order to reach a uniform distribution over the entire area.

• Dismount swath flaps (1) and fasten them with a spring cotter pin (10) on the machine for a later dismantling.

Pos: 75.52 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

81

Settings

Pos: 75.53 /Ü berschriften/Ü berschriften 2/A-E/AAbstand der Walzen einstellen @ 193\mod_1383232082286_78.docx @ 1647075 @ 2 @ 1

10.6 Setting the Distance of the Rollers

Pos: 75.54 /Abkürzungen /CR- Ausführung @ 194\mod_1383299073254_78.docx @ 1647987 @ @ 1

CR design

Pos: 75.55 /BA/Ei nstellungen/M ähwer ke/R ollen-Condi tioners/Ei nstellen des Roll enabstandes EasyCut CR-Ausführung @ 193\mod_1383229458078_78.docx @ 1647015 @ @ 1

2

1

Pos: 76 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-452-0

CRI-0-001

Fig. 51

The roller distance (X) can be adjusted by means of the screw (1), right and left side of the machine. The dimension X = 2 mm must not be below this level to avoid high wear on the rollers.

• Loosen the nuts (2).

Increasing the distance X

• Rotate the screw (1) in the direction (I) to increase the distance.

Reducing the distance X

• Rotate the screw (1) in the direction (II) to reduce the distance.

• Tighten the counter nut (2) again

82

Pos: 77 /Ü berschriften/Überschriften 1/U-Z/Wartung @ 0\mod_1199883581050_78.docx @ 36685 @ 1 @ 1

Maintenance

11

Pos: 78.1 /Überschriften/Überschriften 2/P-T/SSpeziell e Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Maintenance

11.1 Special Safety Instructions

Pos: 78.2 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - U nvorhergesehene Akti onen an der M aschine_1 @ 0\mod_1196782315875_78.docx @ 14851 @ @ 1

Danger! - Unexpected actions on the machine

Effect: Danger to life, injuries or damage to the machine.

• Always make certain that the drive and the engine are switched off before doing any repairs, maintenance or cleaning.

• The cutting discs continue to run!

• Switch off the engine and remove the ignition key.

• Secure the machine against accidental start-up and against rolling!

Pos: 78.3 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Bei unregel mäßiger Kontr olle der Messer kli ngen und H altebolzen @ 0\mod_1196782406281_78.docx @ 14870 @ @ 1

Danger! - When checking the cutter blades and retaining bolts only sporadically

Effect: Danger to life, injuries or damage to the machine.

• Always check the mowing units for damaged, missing or worn blades, retaining bolts, leaf springs and cutting discs/blade drum before starting operation; replace any parts that are damaged, missing or worn!

• Always replace missing and damaged blades in sets to prevent unbalanced rotation!

• Never mount unevenly worn blades on a drum/disc!

• Whenever a blade is changed, also inspect the fasteners and replace them, if necessary!

Pos: 78.4 /Überschriften/Überschriften 3/P-T/PPr obel auf @ 0\mod_1196833698843_78.docx @ 15023 @ 3 @ 1

11.1.1 Test run

Pos: 78.5 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Probel auf M ehrzahl @ 0\mod_1196782825187_78.docx @ 14889 @ @ 1

Danger! - Testing the machine after repair, maintenance or cleaning work and after technical intervention.

Effect: Danger to life or serious injuries

• The mowing unit must be in working position

• Do not switch on the drives until the mowing units are resting on the ground and you are absolutely sure that neither persons, animals nor objects are in the danger zone.

• Start a trial run of the machine only from the driver’s seat.

Pos: 78.6 /Überschriften/Überschriften 2/A-E/EErsatzteile @ 0\mod_1196782991234_78.docx @ 14927 @ 2 @ 1

11.2 Spare Parts

Pos: 78.7 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/WARNUNG - Ver wendung von nicht zug elassenen Ersatzteilen @ 308\mod_1417011577394_78.docx @ 2392925 @ @ 1

Warning! - Using non-approved spare parts.

Effect: Danger to life, serious injuries or loss of warranty claims as well as exclusion of liability

• Use only authentic KRONE spare parts and accessories authorised by the manufacturer.

The use of spare parts, accessories or additional equipment not manufactured, tested or approved by KRONE will exclude any liability for consequential damage.

Pos: 78.8 /BA/Wartung/Hi nweis Verschleiß verringer n @ 0\mod_1199953505303_78.docx @ 37204 @ @ 1

Pos: 78.9 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

To ensure problem-free operation of the machine and to reduce wear and tear, specific maintenance and upkeep intervals must be observed. These include cleaning, greasing, lubricating and oiling parts and components.

83

Maintenance

Pos: 78.10 /Ü berschriften/Ü berschriften 2/U-Z/WWartungstabelle @ 65\mod_1300369413064_78.docx @ 583966 @ 2 @ 1

11.3 Maintenance table

Pos: 78.11 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Wartungstabelle - EasyC ut @ 250\mod_1396960724543_78.docx @ 1937809 @ @ 1

Maintenance work Maintenance interval

Cutter bar

Oil level check

Oil change

All gearboxes

Oil level check

Oil change

Checking cutter blades

Checking retaining bolts for cutter blades

Check material thickness of leaf spring, for blade quick fastener design

Mower disc / mower drum

Linings on the cutter bar

Tightening screws / nuts

All screws

Friction clutch

Venting

Guard cloths

Check guard cloths for wear and damage

V-belt

Pos: 78.12 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Check guard cloths for wear and damage

Checking V-belt tension

X

X

X

X

X

X

Not required

X

X

X

X

X

X

X

X

X

X

X

X

X X

X

84

Pos: 78.13.1 /Ü berschriften/Ü berschriften 2/A-E/AAnzi ehdrehmomente @ 202\mod_1385711894606_78.docx @ 1693123 @ 2 @ 1

Maintenance

11.4 Tightening torques

Pos: 78.13.2 /Ü berschriften/Ü berschriften 3/K-O/MM etrische Gewindeschrauben mit R egelgewi nde @ 322\mod_1424945442462_78.docx @ 2483466 @ 3 @ 1

11.4.1 Metric Thread Screws with Control Thread

Pos: 78.13.3 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewi ndeschr auben mi t R egelgewinde T abelle @ 321\mod_1424760222607_78.docx @ 2477725 @ @ 1

NOTICE

The table does not apply to countersunk screws with hexagonal socket in case the countersunk screw is tightened via hexagonal socket.

Tightening torque in Nm (unless otherwise stated)

A = thread size

(stability class can be seen on screw head)

A

Pos: 78.13.4 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

M4

M5

M6

M8

M10

M12

M14

M16

M20

M22

M24

M27

M30

Stability class

29

42

5.6 8.8 10.9 12.9

Tightening torque (Nm)

3.0

5.9

4.4

8.7

5.1

10

10

25

49

85

15

36

72

125

18

43

84

145

135

210

425

571

730

200

310

610

832

235

365

710

972

1050 1220

1100 1550 1800

1450 2100 2450

85

Maintenance

Pos: 78.13.5 /Ü berschriften/Ü berschriften 3/K-O/MM etrische Gewindeschrauben mit F eing ewinde @ 322\mod_1424945855944_78.docx @ 2484627 @ 3 @ 1

11.4.2 Metric Thread Screws with Fine Thread

Pos: 78.13.6 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewi ndeschr auben mi t F eingewi nde Tabell e @ 321\mod_1424845229172_78.docx @ 2480186 @ @ 1

Tightening torque in Nm (unless otherwise stated)

A

M12 x

1.5:

M14 x 1.5

M16 x 1.5

M18 x 1.5

M20 x 1.5

M24 x 2

M27 x 2

M30 x 1.5

Pos: 78.13.7 /Ü berschriften/Ü berschriften 3/K-O/MM etrische Gewindeschrauben mit Senkkopf und Innensechskant @ 323\mod_1424945970760_78.docx @ 2484818 @ 3 @ 1

5.6

Stability class

8.8 10.9 12.9

Tightening torque (Nm)

88 130 152

145

222

368

465

787

800

213

327

525

662

249

382

614

775

1121 1312

1148 1635 1914

2100 2650

A = thread size

(stability class can be seen on screw head)

11.4.3 Metric Thread Screws with Countersunk Head and Hexagonal Socket

Pos: 78.13.8 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewi ndeschr auben mi t Senkkopf und Innensechskant T abelle @ 321\mod_1424843938347_78.docx @ 2480155 @ @ 1

NOTICE

The table applies only to countersunk screws with hexagonal socket and metric thread which are tightened via hexagonal socket.

Tightening torque in Nm (unless otherwise stated)

A = thread size

(stability class can be seen on screw head)

A

Pos: 78.14 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

M4

M5

M6

M8

M10

M12

M14

M16

M20

Stability class

23

34

5.6 8.8 10.9 12.9

Tightening torque (Nm)

2.5

4.7

3.5

7

4.1

8

8

20

39

68

12

29

58

100

15

35

67

116

108 160 188

168 248 292

340 488 568

A

BM 400 0234

86

Pos: 78.15 /Ü berschriften/Ü berschriften 3/A-E/A/Abweichende Anziehdrehmomente @ 369\mod_1441722353234_78.docx @ 2702740 @ 3 @ 1

11.4.4 Deviating Tightening Torques

Pos: 78.16 /BA/War tung/Drehmomente / Anziehdrehmomente/Abweichendes Dr ehmoment Big M 400 @ 0\mod_1196949184374_78.docx @ 15274 @ @ 1

Screws / nuts

Nut for shear protection (rotary hub)

Bearing housing for cutting disc

Pos: 78.17 /Ü berschriften/Ü berschriften 2/U-Z/Z Z wischengelenkwelle @ 3\mod_1204702241039_78.docx @ 71481 @ 2 @ 1

Bearing housing for blade drum

11.5 Intermediate PTO shaft

Pos: 78.18 /BA/Inbetri ebnahme/EasyCut/Anbau Gel enkwell e/Z wischeng elenkwell e/Z wischeng elenkwelle EC F 360 CV/CR @ 245\mod_1395922648686_78.docx @ 1914733 @ @ 1

2

1

MA [Nm]

300

42

42

Maintenance

Pos: 78.19 /BA/Inbetri ebnahme/EasyCut/Hinweis R ei bkupplung @ 11\mod_1223358975938_78.docx @ 145593 @ @ 1

EC-492-0

Fig. 52

The intermediate universal shaft is mounted with the freewheel (1) to the angular gearbox. The friction clutch (2) of the intermediate universal shaft is attached to the input gearbox.

Note - Friction Clutch

Effect: Conserve functionality and increased service life

• The friction clutch (2) must be vented prior to commissioning and once a year prior to harvesting. (See section Before the Start of the New Season "Friction clutch")

Pos: 79 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

87

EC R 320 EC

EC R 280 EC R 280 CV

Pos: 80.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 53

88

Maintenance

Pos: 80.1 /Überschriften/Überschriften 2/K-O/KKreiselnabe mit Schersicher ung ( optional) @ 4\mod_1213097920976_78.docx @ 86356 @ 2 @ 1

11.6 Rotary hub with shear fuse (optional)

Pos: 80.2 /BA/Wartung/M ähwer ke/Schersicherung/Bild M ähhol m Aufstell ung EC R 280/320 (CV) EC F 320 C V @ 147\mod_1361180309624_78.docx @ 1319551 @ @ 1

EC R 320 EC

Pos: 80.4 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Schnell rotierende Messerteller/M essertrommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Maintenance

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

Pos: 80.5 /BA/Wartung/M ähwer ke/Schersicherung/Leg ende Mähhol m Aufstellung EasyCut´s A,B,R E,LE @ 99\mod_1330074124805_78.docx @ 889331 @ @ 1

Pos: 80.6 /BA/Wartung/M ähwer ke/Schersicherung/Beschr eibung Schersicherung RE,LE @ 99\mod_1330074896634_78.docx @ 889358 @ @ 1 For protection against overload on the mowing units, the rotary hubs (1) are secured with nuts

(2) and shear pins (3).

If the machine strikes obstacles (for example stones), the 2 shear pins in the rotary hub will be sheared off. The rotary hub and nut turn upward on the pinion shaft.

• The cutting discs or drums which move crop to the left (as seen in the direction of travel)

(LE) have left-handed threading.

• The cutting discs or drums which move crop to the right (in the direction of travel) (RE) have right-handed threading.

To distinguish between right-hand (clockwise) threading (RE) and left-hand (anti-clockwise) threading (LE), the nuts (2) and pinion shaft (4) for left-hand threading (LE) have a distinctive grove (a, b).

• Left-handed (LE) nuts (2) have distinctive grooves (a) on the bevel.

• Left-handed (LE) pinion shafts (4) have a distinctive groove (b) on the face.

Pos: 80.7 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Explanation of abbreviations:

A= Direction of rotation "A" to the middle

B= Direction of rotation "B" in pairs

RE= Eccentric bearing housing (clockwise threading, without identifying groove).

LE= Eccentric bearing housing (anticlockwise threading), with identifying groove.

89

Maintenance

Pos: 80.8 /BA/Wartung/M ähwer ke/Schersicherung/Bild M ähhol m Aufstell ung EC F 360 @ 245\mod_1395995206667_78.docx @ 1916051 @ @ 1

Pos: 80.9 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 54

90

Pos: 80.10 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M essertrommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Maintenance

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

Pos: 80.11 /BA/War tung/Mähwer ke/Schersicherung/Legende M ähhol m Aufstellung EasyC ut´s A,B,R E,LE @ 99\mod_1330074124805_78.docx @ 889331 @ @ 1

Pos: 80.12 /BA/War tung/Mähwer ke/Schersicherung/Beschrei bung Schersicher ung R E,LE @ 99\mod_1330074896634_78.docx @ 889358 @ @ 1 For protection against overload on the mowing units, the rotary hubs (1) are secured with nuts

(2) and shear pins (3).

If the machine strikes obstacles (for example stones), the 2 shear pins in the rotary hub will be sheared off. The rotary hub and nut turn upward on the pinion shaft.

• The cutting discs or drums which move crop to the left (as seen in the direction of travel)

(LE) have left-handed threading.

• The cutting discs or drums which move crop to the right (in the direction of travel) (RE) have right-handed threading.

To distinguish between right-hand (clockwise) threading (RE) and left-hand (anti-clockwise) threading (LE), the nuts (2) and pinion shaft (4) for left-hand threading (LE) have a distinctive grove (a, b).

• Left-handed (LE) nuts (2) have distinctive grooves (a) on the bevel.

• Left-handed (LE) pinion shafts (4) have a distinctive groove (b) on the face.

Pos: 80.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Explanation of abbreviations:

A= Direction of rotation "A" to the middle

B= Direction of rotation "B" in pairs

RE= Eccentric bearing housing (clockwise threading, without identifying groove).

LE= Eccentric bearing housing (anticlockwise threading), with identifying groove.

91

Maintenance

Pos: 80.14 /BA/War tung/Mähwer ke/SchersicherungNach dem Abscher en EasyC ut @ 364\mod_1440501433026_78.docx @ 2678607 @ 3 @ 1

11.6.1 After Shearing Off

Caution! - Correct installation position of the bearing housing not observed.

Effect: Damage to the machine

• Right rotating (RE/RZ) cutting discs and drums always have right-handed pinion shafts and nuts (no groove mark on the pinion shaft and nut).

• Left rotating (LE/LZ) cutting discs and drums always have left-handed pinion shafts and nuts

(with groove mark on the pinion shaft and nut).

7

8 a

9

2

3

3a

3a

3

3a

4 d b

1 c

10

EC-255-1

Fig. 55

92

Pos: 81 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Maintenance

• Remove the cutting disc or drum.

• Remove retaining ring (7).

• Unscrew the hexagon head bolts (8).

• Use the special key (10) included with delivery to remove the nut (2).

• Remove the hub (1).

• Remove the damaged shear pins (3).

• Check the nut and hub for damage. Replace damaged parts with KRONE original replacement parts.

• Fill the space above the bearing with grease (c).

• Place the hub on the pinion shaft.

• Drive the new shear pins (3) through the hub (1) and shaft (4).

Note - Note the position of the shear pins!

• Drive the shear pins (3) into the hole from outside until the end of the pin reaches the surface of the hub (d).

• he slots of the shear pins (3) must be mounted facing each other horizontally (see detail (I)).

• Install the nut (2) using the special key (10) included with delivery (tighten to a tightening torque of 300 Nm).

• Install and tighten the hexagon head bolts (8) with detent edged washers.

• Install the retaining ring (7).

• Install the cutting disc (5) or blade drum (6).

93

Maintenance - Gearbox

Pos: 82 /Ü berschriften/Überschriften 1/U-Z/Wartung - Getriebe @ 2\mod_1203058202823_78.docx @ 64495 @ 1 @ 1

12

Pos: 83.1 /Überschriften/Überschriften 2/A-E/EEing angsgetriebe @ 0\mod_1197005979596_78.docx @ 15454 @ 2 @ 1

Maintenance - Gearbox

12.1 Input gearbox

Pos: 83.2 /BA/Wartung/Hi nweis Ölstandskontr olle i n Arbeitsstellung und i n waag erechter Stell ung der Maschi ne vor nehmen @ 194 \mod_1383554973754_78.docx @ 1649577 @ @ 1

Note

Perform oil level check and oil change while the machine is in a horizontal position!

Pos: 83.3 /BA/Wartung/Öl kontr olle_Wechsel/Mähwer ke/Bild Winkelgetri ebe EC F 360 CV/CR @ 245\mod_1395998936051_78.docx @ 1916180 @ @ 1

4

1

2

EC-503-0

Fig. 56

Pos: 83.4 /BA/Wartung/Öl kontr olle_Wechsel/Öl wechsel / Öl kontr olle:Legende zu Grafi k Kontrollschraube / Ablassschraube @ 194\mod_1383299451132_78.docx @ 1648045 @ @ 1

1) Inspection screw / control hole

Pos: 83.5 /BA/Wartung/Öl kontr olle_WechselÖlqualität/Ölmenge: siehe Kapitel T echnische Daten der Maschi ne @ 371\mod_1441958324612_78.docx @ 2710777 @ @ 1

2) Drain plug

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating

Materials”

Pos: 83.6 /BA/Wartung/Öl kontr olle_Wechsel/Öl kontroll e / Öl wechsel Inter vall: si ehe Kapitel Wartung „ Wartung stabelle“ @ 134\mod_1350483605921_78.docx @ 1188115 @ @ 1

Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”

Pos: 83.7 /BA/Wartung/Öl kontr olle_Wechsel/Öl wechsel _ALT /Schutz ( 4) demontieren @ 58\mod_1296735396286_78.docx @ 553788 @ @ 1

• Remove the guard (4)

Pos: 83.8 /BA/Wartung/Öl kontr olle_WechselÖl kontrolle NEU über Kontrollschraube @ 140\mod_1355141753680_78.docx @ 1244582 @ @ 1

Oil level check:

• Screw out inspection screw.

• Oil level up to control hole.

If the oil reaches the control hole:

• Screw in the inspection screw and tighten it securely.

If the oil does not reach the control hole:

• Screw out filler plug.

• Top up oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 83.9 /BA/Wartung/Öl kontr olle_Wechsel/Öl wechsel _ALT /Schutz ( 4) monti eren @ 58\mod_1296735440474_78.docx @ 553814 @ @ 1

• Install the guard (4)

Pos: 83.10 /BA/War tung/Öl kontroll e_Wechsel Öl wechsel NEU @ 140\mod_1355142057277_78.docx @ 1244610 @ @ 1

Oil change:

Collect escaping oil in a suitable container.

• Screw out oil drain plug and drain the oil.

• Screw out inspection screw and filler plug.

• Screw in oil drain plug and tighten it securely.

• Top up new oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 83.11 /BA/War tung/Öl kontroll e_Wechsel/Öl wechsel _ALT/Schutz (4) montier en @ 58\mod_1296735440474_78.docx @ 553814 @ @ 1

• Install the guard (4)

Pos: 83.12 /BA/War tung/Öl kontroll e_Wechsel/Hi nweis - Altöl or dnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 84 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

94

Pos: 85 /Ü berschriften/Überschriften 2/U-Z/WWinkelgetri ebe @ 0\mod_1197005918299_78.docx @ 15435 @ 3 @ 1

Maintenance - Gearbox

12.2 Angular gearbox

Pos: 86 /Abkürzungen /CV- Ausführung @ 95\mod_1328530180147_78.docx @ 799128 @ @ 1

CV-Design

Pos: 87 /BA/Wartung/Hi nweis Ölstandskontr olle i n Arbeitsstell ung und i n waag erechter Stell ung der Maschi ne vornehmen @ 194 \mod_1383554973754_78.docx @ 1649577 @ @ 1

Note

Perform oil level check and oil change while the machine is in a horizontal position!

Pos: 88 /BA/Wartung/Öl kontr olle_Wechsel/Mähwer ke/Winkelgetriebe EC F 360 CV Bil d @ 248\mod_1396592486182_78.docx @ 1932134 @ @ 1

1

2

EC-522-0

Fig. 57

Pos: 89 /BA/Wartung/Öl kontr olle_Wechsel/Öl wechsel / Öl kontr olle:Legende zu Grafi k Kontrollschraube / Ablassschraube / Ei nfüllschraube @ 194\mod_1383288259662_78.docx @ 1647783 @ @ 1

1) Inspection screw / control hole 2) Drain plug

3) Filler plug / oil filling hole

Pos: 90 /BA/Wartung/Öl kontr olle_Wechsel/Ölqualität/Öl menge: si ehe Kapitel T echnische D aten der M aschine @ 371\mod_1441958324612_78.docx @ 2710777 @ @ 1

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating

Materials”

Pos: 91 /BA/Wartung/Öl kontr olle_Wechsel/Öl kontroll e / Öl wechsel Inter vall: si ehe Kapitel Wartung „ Wartungstabelle“ @ 134\mod_1350483605921_78.docx @ 1188115 @ @ 1

Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”

Pos: 92 /BA/Wartung/Öl kontr olle_WechselÖl kontrolle NEU über Kontrollschraube @ 140\mod_1355141753680_78.docx @ 1244582 @ @ 1

Oil level check:

• Screw out inspection screw.

• Oil level up to control hole.

If the oil reaches the control hole:

• Screw in the inspection screw and tighten it securely.

If the oil does not reach the control hole:

• Screw out filler plug.

• Top up oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 93 /BA/Wartung/Öl kontr olle_WechselÖl wechsel N EU @ 140\mod_1355142057277_78.docx @ 1244610 @ @ 1

Oil change:

Collect escaping oil in a suitable container.

• Screw out oil drain plug and drain the oil.

• Screw out inspection screw and filler plug.

• Screw in oil drain plug and tighten it securely.

• Top up new oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 94 /BA/Wartung/Öl kontr olle_Wechsel/Hinweis - Altöl ordnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 95 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

95

Maintenance - Gearbox

Pos: 96.1 /Überschriften/Überschriften 2/U-Z/WWi nkelgetriebe @ 0\mod_1197005918299_78.docx @ 15435 @ 2 @ 1

12.3

Pos: 96.2 /Abkürzungen /CR-Ausführ ung @ 194\mod_1383299073254_78.docx @ 1647987 @ @ 1

Angular gearbox

Pos: 96.3 /Überschriften/Überschriften 3/K-O/OOberteil @ 10\mod_1221639445993_78.docx @ 135690 @ 3 @ 1

CR design

12.3.1 Top part

Pos: 96.4 /BA/Wartung/Hi nweis Ölstandskontr olle i n Arbeitsstellung und i n waag erechter Stell ung der Maschi ne vor nehmen @ 194 \mod_1383554973754_78.docx @ 1649577 @ @ 1

Note

Perform oil level check and oil change while the machine is in a horizontal position!

Pos: 96.5 /BA/Wartung/Öl kontr olle_Wechsel/Mähwer ke/Bild Winkelgetri ebe Oberteil CRI @ 10 \mod_1221555831463_78.docx @ 135326 @ @ 1

2

1

EC-210-0

Figure 58

Pos: 96.6 /BA/Wartung/Öl kontr olle_Wechsel/Öl wechsel / Öl kontr olle:Legende zu Grafi k Kontrollschraube / Ei nfüllschr aube @ 194\mod_1383298407773_78.docx @ 1647929 @ @ 1

1) Inspection screw / control hole 2) Filler plug / oil filling hole

Pos: 96.7 /BA/Wartung/Öl kontr olle_WechselÖlqualität/Ölmenge: siehe Kapitel T echnische Daten der Maschi ne @ 371 \mod_1441958324612_78.docx @ 2710777 @ @ 1

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating

Materials”

Pos: 96.8 /BA/Wartung/Öl kontr olle_Wechsel/Öl kontroll e / Öl wechsel Inter vall: si ehe Kapitel Wartung „ Wartungstabelle“ @ 134\mod_1350483605921_78.docx @ 1188115 @ @ 1

Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”

Pos: 96.9 /BA/Wartung/Öl kontr olle_WechselÖl kontrolle NEU über Kontrollschraube @ 140\mod_1355141753680_78.docx @ 1244582 @ @ 1

Oil level check:

• Screw out inspection screw.

• Oil level up to control hole.

If the oil reaches the control hole:

• Screw in the inspection screw and tighten it securely.

If the oil does not reach the control hole:

• Screw out filler plug.

• Top up oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 96.10 /BA/War tung/Öl kontroll e_Wechsel/Öl wechsel N EU Kontr ollschr aube, Einfüllschraube Öl absaugen @ 207\mod_1386773599651_78.docx @ 1716145 @ @ 1

Oil change:

Collect escaping oil in a suitable container.

• Screw out inspection screw and filler plug and drain the oil.

• Top up new oil via oil filling hole until the control hole is reached.

• Screw in inspection screw and filler plug and tighten them securely.

Pos: 96.11 /BA/War tung/Öl kontroll e_Wechsel/Hi nweis - Altöl or dnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 97 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

96

Pos: 98.1 /Überschriften/Überschriften 2/U-Z/WWi nkelgetriebe @ 0\mod_1197005918299_78.docx @ 15435 @ 2 @ 1

12.4

Pos: 98.2 /Abkürzungen /CR-Ausführ ung @ 194\mod_1383299073254_78.docx @ 1647987 @ @ 1

Angular gearbox

Pos: 98.3 /Überschriften/Überschriften 3/U-Z/Unterteil @ 10\mod_1221640227712_78.docx @ 135712 @ 3 @ 1

CR design

Maintenance - Gearbox

12.4.1 Bottom part

Pos: 98.4 /BA/Wartung/Hi nweis Ölstandskontr olle i n Arbeitsstellung und i n waag erechter Stell ung der Maschi ne vor nehmen @ 194 \mod_1383554973754_78.docx @ 1649577 @ @ 1

Note

Pos: 98.5 /BA/Wartung/Öl kontr olle_Wechsel/Mähwer ke/Bild Winkelgetri ebe CR I @ 0 \mod_1197013688111_78.docx @ 15844 @ @ 1

Perform oil level check and oil change while the machine is in a horizontal position!

2

1

EC-189-0

Fig. 59:

Pos: 98.6 /BA/Wartung/Öl kontr olle_Wechsel/Öl wechsel / Öl kontr olle:Legende zu Grafi k Kontrollschraube / Ablassschraube @ 194\mod_1383299451132_78.docx @ 1648045 @ @ 1

1) Inspection screw / control hole 2) Drain plug

Pos: 98.7 /BA/Wartung/Öl kontr olle_WechselÖlqualität/Ölmenge: siehe Kapitel T echnische Daten der Maschi ne @ 371\mod_1441958324612_78.docx @ 2710777 @ @ 1

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating

Materials”

Pos: 98.8 /BA/Wartung/Öl kontr olle_Wechsel/Öl kontroll e / Öl wechsel Inter vall: si ehe Kapitel Wartung „ Wartungstabelle“ @ 134\mod_1350483605921_78.docx @ 1188115 @ @ 1

Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”

Pos: 98.9 /BA/Wartung/Öl kontr olle_WechselÖl kontrolle NEU über Kontrollschraube ohne Einfüllschraube @ 158\mod_1364483633589_78.docx @ 1391741 @ @ 1

Oil level check:

• Screw out inspection screw.

• Oil level up to control hole.

If the oil reaches the control hole:

• Screw in the inspection screw and tighten it securely.

If the oil does not reach the control hole:

• Top up oil via control hole until the control hole is reached.

• Screw in the inspection screw and tighten it securely.

Pos: 98.10 /BA/War tung/Öl kontroll e_Wechsel Öl wechsel NEU ohne Ei nfüllschr aube @ 158\mod_1364483760090_78.docx @ 1391770 @ @ 1

Oil change:

Collect escaping oil in a suitable container.

• Screw out oil drain plug and drain the oil.

• Screw out inspection screw.

• Screw in oil drain plug and tighten it securely.

• Top up new oil via control hole until the control hole is reached.

• Screw in the inspection screw and tighten it securely.

Pos: 98.11 /BA/War tung/Öl kontroll e_Wechsel/Hi nweis - Altöl or dnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 99 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

97

Maintenance - Gearbox

Pos: 100.1 /Ü berschriften/Ü berschriften 2/F-J/GGetri ebe für ober en Walzenantrieb @ 11\mod_1223618840051_78.docx @ 148283 @ 2 @ 1

12.5 Gearbox for Top Roller Drive

Pos: 100.2 /Abkürzungen /CR- Ausführung @ 194\mod_1383299073254_78.docx @ 1647987 @ @ 1

CR design

Pos: 100.3 /BA/War tung/Hinweis Ölstandskontroll e in Ar beitsstellung und in waager echter Stellung der M aschine vor nehmen @ 194\mod_1383554973754_78.docx @ 1649577 @ @ 1

Note

Perform oil level check and oil change while the machine is in a horizontal position!

Pos: 100.4 /BA/War tung/Öl kontroll e_Wechsel/M ähwer ke/Bild Getriebe für oberen Walzenantri eb CR @ 194\mod_1383559678635_78.docx @ 1649994 @ @ 1

3

1

2

Fig. 60

Pos: 100.5 /BA/War tung/Öl kontroll e_Wechsel/Öl wechsel / Öl kontroll e:Leg ende zu Gr afi k Kontrollschraube / Abl assschr aube / Ei nfüllschr aube @ 194\mod_1383288259662_78.docx @ 1647783 @ @ 1

1) Inspection screw / control hole

3) Filler plug / oil filling hole

EC-453-0

2) Drain plug

Pos: 100.6 /BA/War tung/Öl kontroll e_Wechsel Ölqualität/Öl menge: si ehe Kapitel Technische D aten der M aschine @ 371\mod_1441958324612_78.docx @ 2710777 @ @ 1

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating

Materials”

Pos: 100.7 /BA/War tung/Öl kontroll e_Wechsel/Öl kontrolle / Öl wechsel Inter vall : siehe Kapitel Wartung „Wartungstabell e“ @ 134 \mod_1350483605921_78.docx @ 1188115 @ @ 1

Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”

Pos: 100.8 /BA/War tung/Öl kontroll e_Wechsel Öl kontr olle N EU über Kontr ollschr aube @ 140\mod_1355141753680_78.docx @ 1244582 @ @ 1

Pos: 100.9 /BA/War tung/Öl kontroll e_Wechsel Öl wechsel NEU @ 140\mod_1355142057277_78.docx @ 1244610 @ @ 1

Oil level check:

• Screw out inspection screw.

• Oil level up to control hole.

If the oil reaches the control hole:

• Screw in the inspection screw and tighten it securely.

If the oil does not reach the control hole:

• Screw out filler plug.

• Top up oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Oil change:

Collect escaping oil in a suitable container.

• Screw out oil drain plug and drain the oil.

• Screw out inspection screw and filler plug.

• Screw in oil drain plug and tighten it securely.

• Top up new oil via oil filling hole until the control hole is reached.

• Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 100.10 /BA/Wartung/Öl kontr olle_Wechsel/Hi nweis - Altöl ordnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 101 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

98

Pos: 102 /Überschriften/Ü berschriften 2/P-T/RRiemenantri eb spannen @ 248\mod_1396532691160_78.docx @ 1931044 @ 2 @ 1

Maintenance - Gearbox

12.6 Tensioning Belt Drive

Pos: 103 /Abkürzungen /C V-Ausführung @ 95\mod_1328530180147_78.docx @ 799128 @ @ 1

CV-Design

Pos: 104 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/WARNUN G! – Verletzungsgefahr durch unter F ederspannung stehende Bauteile! @ 252\mod_1397140836170_78.docx @ 1946524 @ @ 1

WARNING!

When tensioning and releasing, the blade key is under spring tension. If the blade key is released too early, then it will spring back.

This may result in injuries.

• Do not release the blade key when tensioning and releasing.

Pos: 105 /BA/Einstellungen/M ähwer ke/Z etterdr ehzahl/Ri ementrieb spannen EC F 360 C V/CR Bild @ 248 \mod_1396531120669_78.docx @ 1930925 @ @ 1

4

8

5

2

3

1

6

7

EC-521-0

Fig. 61

Pos: 106 /BA/Einstellungen/M ähwer ke/Z etterdr ehzahl/Spannen des Riementiebes EC F 360 C V/CR T ext @ 248\mod_1396531113982_78.docx @ 1930716 @ @ 1

When tensioning the V-belts, make certain that the adjustment aid (1) is flush with the upper edge of the tension spring (2).

• Loosen nuts (3) if the adjustment aid is not flush.

• Tension with threaded rod (4), tension spring (2) and lock with nuts (3) so that the adjustment aid is flush with the upper edge of the spring.

• Mount V-belt guard (8).

Pos: 107 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

99

Maintenance - Gearbox

Pos: 108.1 /Ü berschriften/Ü berschriften 2/K-O/OÖlstandskontr olle und Öl wechsel am M ähhol m @ 0\mod_1197017549815_78.docx @ 15963 @ 2 @ 1

12.7

Pos: 108.2 /Ü berschriften/Ü berschriften 3/K-O/OÖl wechsel @ 0\mod_1197021941955_78.docx @ 16139 @ 3 @ 1

Oil level check and oil change on the cutter bar

12.7.1 Oil change

Pos: 108.3 /BA/War tung/Mähwer ke/Hi nweis Ein Öl wechsel am M ähhol m ist nicht erforderlich. @ 68\mod_1304577391388_78.docx @ 628708 @ @ 1

Pos: 108.4 /Ü berschriften/Ü berschriften 3/K-O/OÖl kontroll e @ 0\mod_1197021908190_78.docx @ 16120 @ 3 @ 1

Note

No oil change is required on the cutter bar.

12.7.2 Checking the oil level

Pos: 108.5 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M essertrommel_2 @ 0\mod_1197022569252_78.docx @ 16165 @ @ 1

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

Lower guards. Nobody should be in the danger zone around the machine.

Pos: 108.6 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M essertrommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Pos: 108.7 /Ü berschriften/Ü berschriften 3/K-O/MM ähhol m ausrichten @ 0\mod_1197017956815_78.docx @ 16042 @ 3 @ 1

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

12.7.3

Pos: 108.8 /BA/War tung/Mähwer ke/M ähhol m ausrichten EasyC ut @ 3\mod_1204721803648_78.docx @ 72358 @ @ 1

Aligning the Cutter Bar

Pos: 108.9 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 62

Oil level check

• Align the cutter bar using a spirit level (1).

Crosswise

• Lay the spirit level on top of the cutting disc hub parallel to the direction of travel.

Lengthwise

• Lay the spirit level (1) on top of two mower discs.

EC-0-001

100

Pos: 108.10 /BA/Wartung/M ähwer ke/Öl kontr olle M ähhol m Easycut @ 3\mod_1204723206930_78.docx @ 72428 @ @ 1

Maintenance - Gearbox

• Allow the machine to run briefly. Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop

Pos: 109 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-0-003

Fig. 63:

Check the oil level before every use

• Remove the oil level inspection screw (1) from the cutting disc hub

• The oil level must be up to the bore hole. If required, top up the oil (SAE 90)

• Screw in the oil level inspection screw (1) again and tighten securely

101

Maintenance - Blade Changing

Pos: 110 /Überschriften/Ü berschriften 1/U-Z/Wartung - M esser wechsel @ 107\mod_1334638484298_78.docx @ 968003 @ 1 @ 1

13 Maintenance - Blade Changing

Pos: 111.1 /Ü berschriften/Ü berschriften 2/K-O/KKontroll e der M ähklingen und Messer halterung @ 0\mod_1197265641329_78.docx @ 16323 @ 2 @ 1

13.1 Checking the Cutter Blades and Blade Holder

Pos: 111.2 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - F ehl ende und beschädigte M ähklingen und Mähklingenhal ter ung en @ 0\mod_1197265722813_78.docx @ 16342 @ @ 1

Warning! - Missing and damaged cutter blades and cutter blade retainers.

Effect: Danger to life, serious injuries or damage to the machine

• Check cutter blades at least once per day and check retaining bolts every time you change the blades or after contact with foreign objects.

• Immediately replace missing or damaged cutter blades and cutter blade retainers

Pos: 111.3 /BA/War tung/Mähwer ke/N ach Beendigung Schutz in Schutzstell ung bringen Bild EC F 360 C V/CR @ 332\mod_1428650306921_78.docx @ 2540825 @ @ 1

1

EC-504-1

Abb. 64

Pos: 111.4 /BA/War tung/Mähwer ke/N ach Beendigung Schutz in Schutzstell ung bringen T ext EC F 320 C V @ 102\mod_1331027373525_78.docx @ 901600 @ @ 1

To check and fit the blades, fold up the protective device (1). The safety device can be opened with the aid of a sharp instrument (e.g. blade key, screwdriver).

• Use the sharp instrument to press down the handle; fold up the protective cover.

• Now the blades are freely accessible.

Note

After the inspection and installation tasks are completed, fold down the protective device back into position.

Pos: 111.5 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

102

Pos: 111.6 /Ü berschriften/Ü berschriften 3/K-O/MM ähkli ngen @ 0\mod_1197265959110_78.docx @ 16361 @ 3 @ 1

Maintenance - Blade Changing

13.1.1 Cutter Blades

Pos: 111.7 /BA/War tung/Mähwer ke/Di e Bohr ung der M ähklingen kann sich durch Verschl eiß aufweiten. @ 10\mod_1221048982715_78.docx @ 131675 @ @ 1 The borehole on the cutter blades may spread due to wear.

Pos: 111.8 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung - Z u geri nge M aterialstär ke an den Mähkling en_neu @ 312\mod_1418983956660_78.docx @ 2409555 @ @ 1

Danger! - Insufficient thickness of material on the cutter blades.

Pos: 111.9 /BA/War tung/Mähwer ke/M ähklingen beidseitig ver wenbar_neu @ 3\mod_1204728012601_78.docx @ 72608 @ @ 1

Effect: Danger to life or serious injuries.

• The cutter blades must be replaced at the latest when the wear limit is reached (see mark

(1) on the cutter blade; dimension a less than or equal to 13 mm). a

1

EC 253 0

Fig. 65

Pos: 111.10 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note - The cutter blades can be turned around and used on both sides.

• When cutter blades are missing or damaged, they must be replaced as a complete set.

This prevents dangerous unbalanced rotation

103

Maintenance - Blade Changing

Pos: 111.11 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/M esserschr aubverschl uss Haltebolzen 14 mm @ 0\mod_1197267907375_78.docx @ 16425 @ 3 @ 1

13.1.2 Blade screw connection

Danger! - Insufficient thickness of material on the retaining bolts.

Effect: Danger to life or serious injuries.

• At every blade changing check the thickness of the holding bolts material.

• Damage or worn retaining bolts must always be replaced by sets on each cutting disc/blade drum!

• The material thickness of the retaining bolts must not be less than 14 mm at the weakest point.

Pos: 111.12 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 66 min. 14 mm

EC-240-0

104

Pos: 111.13 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/M esserschnellverschluss H altebolzen 14mm @ 0\mod_1197268087875_78.docx @ 16444 @ 3 @ 1

13.1.3 Blade Quick-Fit Device

Maintenance - Blade Changing

Danger! - Insufficient thickness of material on the retaining bolts.

Effect: Danger to life or serious injuries.

• At every blade changing check the thickness of the holding bolts material.

• Damage or worn retaining bolts must always be replaced by sets on each cutting disc/blade drum!

• The material thickness of the retaining bolts must not be less than 14 mm at the weakest point.

• The material thickness of the leaf spring must not be less than 3 mm at the weakest point.

Pos: 111.14 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 67 min. 14 mm

EC-239-0

105

Maintenance - Blade Changing

Pos: 111.15 /BA/Wartung/M ähwer ke/R egel mäßige Kontr olle der Bl attfeder n @ 0\mod_1197268274609_78.docx @ 16464 @ 3 @ 1

13.1.4 Periodical Inspection of the Leaf Springs

Danger! - Worn application seam on the leaf springs.

Effect: Danger to life or serious injuries.

• Check the leaf springs for damages at least once a day or after contact with foreign objects.

• The abrasion limit of the leaf springs will be achieved if the application seam (1) is worn on one point.

1 1

EC 225 0

Fig. 68

Pos: 111.16 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

Use only original Krone spare parts to replace the leaf springs.

106

Pos: 111.17 /BA/Wartung/M ähwer ke/R egel mäßige Kontr olle der Messerteller bzw. -trommeln @ 0\mod_1197268487390_78.docx @ 16483 @ 3 @ 1

13.1.5

Maintenance - Blade Changing

Periodical Inspection of the Cutting Discs / Blade Drums

Danger! - Deformed Cutting Discs / Blade Drums

Effect: Danger to life or serious injuries.

• Check the cutting discs or blade drums for damages at least once per day or after contact with foreign objects.

• In case of deformed cuttings discs or drums, the dimension of A = 48 mm must never be exceeded.

1

A

EC-0-211

Fig. 69

Pos: 111.18 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The cutting discs or drums must be replaced by Original Krone spare parts only.

107

Maintenance - Blade Changing

Pos: 111.19 /BA/Wartung/M ähwer ke/Verschl eissgrenze für Auswaschungen @ 0\mod_1197268738875_78.docx @ 16502 @ 3 @ 1

13.1.6 Abrasion Limit

Danger! - Abrasion on the cutting discs / blade drums

Effect: Danger to life or serious injuries.

• The abrasion limit (2) will be achieved if the min. material thickness of 3 mm is no longer given.

2

2

Pos: 111.20 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-226-0

Fig. 70

Note

If cutting discs or blade drums show deformations or wear in form of abrasions (2) or similar, these components have to be replaced by Original Krone spare parts .

108

Pos: 111.21 /Ü berschriften/Ü berschriften 2/K- O/MMesser wechsel an M essertell ern @ 0\mod_1197269068562_78.docx @ 16521 @ 2 @ 1

Maintenance - Blade Changing

13.2 Blade Changing on Cutting Discs

Pos: 111.22 /BA/Sicher hei t/7. Gefahrenhinweise alt/Mähwer ke/Gefahr - Schnell rotier ende M esser tell er/Messertr ommel n_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

Pos: 111.23 /BA/Sicher hei t/7. Gefahrenhinweise alt/Mähwer ke/Gefahr - Sich lösende M ähklingen @ 0\mod_1197269483265_78.docx @ 16540 @ @ 1

Pos: 111.24 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - Cutter blades coming loose

Effect: Danger to life or serious injuries.

• After changing the blades check that they fit perfectly and that they can move freely.

• Whenever a blade is changed, also inspect the fasteners and replace them, if necessary!

• Always replace missing and damaged blades in sets to prevent unbalanced rotation!

• Never mount unevenly worn blades on a drum/disc!

109

Maintenance - Blade Changing

Pos: 111.25 /Ü berschriften/Ü berschriften 3/K- O/MMesserschr aubverschl uss @ 0\mod_1197270941296_78.docx @ 16578 @ 3 @ 1

13.2.1 Blade Screw Connection

Pos: 111.26 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/Beschr eibung M esser wechsel M esserschr aubverschluss @ 47\mod_1285661949953_78.docx @ 456898 @ @ 1

EC-0-250

Pic. 71

• Fold up safety device

• Clean the area

• Remove damaged or worn blades

• To fit the blades, insert the blade (5) between the wear skid (2) and the cutting disc (1)

• Insert the retaining bolt (3) from below through the wear skid, the blade and the cutting disc

• Place the locknut (4) on the retaining bolt from above and tighten it firmly (tightening torque refer to chapter “Torques”)

• Repeat the process for all blades

• After fitting the blades, fold the safety device down again

Note

• The cutter blades of anticlockwise rotating cutting discs / blade drums are different to those of clockwise rotating ones. Make certain the direction of rotation is correct when installing!

• The arrow on the cutter blades must match the direction of rotation of the corresponding cutting discs / blade drums

• The locknut (4) used to secure the retaining bolts must not be used more than once

Order No. for clockwise rotating blade: 139-889

Pos: 111.27 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Order No. for anticlockwise rotating blade: 139-888

110

Pos: 111.28 /Ü berschriften/Ü berschriften 3/K- O/MMesserschnell verschluss @ 0\mod_1197271019859_78.docx @ 16597 @ 3 @ 1

13.2.2 Blade Quick-Fit Device

Pos: 111.29 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/Beschr eibung M esser wechsel M esserschnellverschluss @ 0\mod_1197271100500_78.docx @ 16616 @ @ 1

Maintenance - Blade Changing

2 3 4

5

EC-251-0

Fig. 72

• Clean the area.

• Remove damaged or worn blades.

• Push the special tool (1) {blade key} between the cutter disc (4) and leaf spring (3) and press down with one hand.

• Guide a new blade (2) onto the retaining bolt and allow the blade key to return upwards.

• After fitting the blades, fold the protective device down again.

Note

• The cutter blades of anticlockwise rotating cutting discs / blade drums are different than those of clockwise rotating ones. Make certain the direction of rotation is correct when installing!

• The arrow on the cutter blades must match the direction of rotation of the corresponding cutting discs / blade drums.

• The hex nut (4) used to secure the retaining bolts must not be used more than once.

Order No. for clockwise rotating blade: 139-889

Pos: 111.30 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Order No. for anticlockwise rotating blade: 139-888

111

Maintenance - Blade Changing

Pos: 111.31 /BA/Wartung/M ähwer ke/Stoß kanten erneuern @ 0\mod_1197271320468_78.docx @ 16636 @ 2 @ 1

13.3 Replacing the linings

Caution! - If the linings are checked irregularly.

Effect: Damage to the machine

• Always check the mowing unit for damaged linings prior to start-up and replace linings, if necessary!

• Adjust the welding current and the welding material to the cutter bar material and to the lining or carry out a trial welding if necessary.•

EC-0-012

Fig. 73

• Open the welding seams of the old lining.

• Remove the lining

• Deburr the contact surface.

Pos: 113 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-252-0

Fig. 74

• Adapt the new lining (3).

• Weld short I seams on the upper surface of the cutter bar in the areas marked (1) (each should be approx. 30 mm).

• Do not weld the edges (2).

• On the

lower surface

of the cutter bar, weld the lining (3) to the cutter bar along the whole length in area (5).

• Do not weld the edges (4).

112

Pos: 114.1 /Ü berschriften/Ü berschriften 1/U-Z/Wartung - Schmierpl an @ 0\mod_1197359304198_78.docx @ 18232 @ 1 @ 1

14

Pos: 114.2 /Ü berschriften/Ü berschriften 2/P-T/SSpezi elle Sicher heitshi nweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Maintenance

– lubrication chart

Maintenance – lubrication chart

14.1 Special Safety Instructions

Pos: 114.3 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung - R eparatur _Wartung_R einigungs_4 allgemei n EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1

WARNING!

When performing repair, maintenance or cleaning work or in case of technical intervention, drive elements may start moving (caution: cutting discs continue to run).

Effect: Danger to life, injuries or damage to the machine.

• Turn off the PTO shaft.

• Move the machine to the working position and lower it to the ground.

• Switch off the engine of the tractor, remove the ignition key and carry it with you.

• Secure the tractor against accidental start-up and against rolling.

• After the repair, maintenance, cleaning work or technical modifications are completed, mount all protective covers and safety devices properly again.

• Avoid skin contact with oils, greases, cleaning agents and solvents.

Pos: 114.4 /Ü berschriften/Ü berschriften 2/A-E/AAntri ebsgelenkwelle @ 116\mod_1340698247730_78.docx @ 1018167 @ 2 @ 1

• In the event of injuries or burns due to oils, cleaning agents or solvents, contact a physician immediately.

• All other safety instructions must also be followed to avoid injuries and accidents.

14.2 Universally-Jointed Drive Shaft

Pos: 114.5 /BA/War tung/Gelenkwelle schmi eren/Abschmi eren Gel enkwell e EasyC ut 100 h @ 44\mod_1275544141265_78.docx @ 392033 @ @ 1

Pos: 114.6 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 75

Lubricate the PTO shafts at the intervals indicated in the drawing with a multi-purpose grease.

Follow the operating instructions of the PTO shaft manufacturer.

113

Maintenance – lubrication chart

Pos: 114.7 /Ü berschriften/Ü berschriften 2/U-Z/Z Z wischengelenkwelle @ 3\mod_1204702241039_78.docx @ 71481 @ 2 @ 1

14.3 Intermediate PTO shaft

Pos: 114.8 /BA/War tung/Gelenkwelle schmi eren/Abschmi eren Z wischeng elenkwelle Bild EasyC ut F 360 CV/CR @ 245\mod_1396000405369_78.docx @ 1916385 @ @ 1

EC-505-0

Fig. 76

Pos: 114.9 /BA/War tung/Gelenkwelle schmi erenAbschmier en Gelenkwelle Text (2015- 10- 28 15:29:50) @ 16\mod_1235638171674_78.docx @ 199556 @ @ 1

Lubricate the PTO shafts at the intervals indicated in the drawing with a multi-purpose grease.

Follow the operating instructions of the PTO shaft manufacturer.

Pos: 114.10 /Ü berschriften/Ü berschriften 2/P-T /SSchmi erpl an @ 0\mod_1197361829026_78.docx @ 18495 @ 2 @ 1

14.4 Lubrication Chart

Pos: 114.11 /BA/Wartung/M ähwer ke/EasyCut / AM M ähwer ke/Schmi erpl äne/Schmier plan EasyCut F 320 C V/F 360 C V/CR Bild @ 326\mod_1426064110757_78.docx @ 2505685 @ @ 1

EasyCut F 320 CV

EasyCut F 360 CV

Pos: 115 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 77

114

EasyCut 360 CR

EC-506-1

Pos: 116.1 /Ü berschriften/Ü berschriften 1/A-E/Einl ager ung @ 0\mod_1197385459120_78.docx @ 19966 @ 1 @ 1

Placing in Storage

15 Placing in Storage

Pos: 116.2.1 /BA/Ei nlag erung/Maschi ne an einem trockenem Ort abstellen @ 70\mod_1305630069850_78.docx @ 638292 @ @ 1

• Park the machine in a dry location, but not in the vicinity of artificial fertilisers or livestock buildings.

Pos: 116.2.2 /BA/Ei nlag erung/Vor der Einwi nterung di e M aschine i nnen und außen gründlich r einigen @ 70 \mod_1305635346852_78.docx @ 638460 @ @ 1

Pos: 116.2.3 /BA/Ei nlag erung/Gelenkwelle ausei nanderzi ehen und einfetten @ 70\mod_1305631424563_78.docx @ 638348 @ @ 1

• Before placing the machine in winter storage, clean inside and outside thoroughly. If you use a high-pressure cleaner to do this. do not keep a stream of water directed at bearing points. After cleaning is completed, lubricate all lubrication points. Do not wipe off any grease that comes out of bearing points. The hardened grease will provide additional protection against moisture.

• Disassemble the PTO shaft. Lubricate the inner tubes and the guard tube with grease.

Grease the lubrication points on the cross joint and on the bearing rings of the guard tubes.

Pos: 116.2.4 /BA/Ei nlag erung/All e Gelenkstell en ei nöl en @ 70\mod_1305633347429_78.docx @ 638432 @ @ 1

• Oil all joint points!

Pos: 116.2.5 /BA/Ei nlag erung/Lackschäden ausbessern, bl anke Stell en gr ündlich mit R ostschutzmittel konser vier en @ 70\mod_1305630900253_78.docx @ 638320 @ @ 1

Pos: 116.2.6 /BA/Ei nlag erung/All e beweglichen Bauteil e überpr üfen @ 70\mod_1305632768685_78.docx @ 638404 @ @ 1

• Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection agent.

• Check all movable components such as deflector rollers, joints, tension rollers, etc. to make certain they move easily. If necessary remove, clean, grease and remount. If necessary, replace with new parts.

Pos: 116.2.7 /BA/Ei nlag erung/Ver wenden Sie nur Original-KRON E-Ersatzteil e @ 70\mod_1305632212285_78.docx @ 638376 @ @ 1

• Use only original KRONE replacement parts.

Pos: 116.2.8 /BA/Ei nlag erung/Sammelliste erstellen @ 70\mod_1305626681125_78.docx @ 638264 @ @ 1

Perform the necessary repair tasks during the time immediately after the harvest season. Draw up a list of all replacement parts you will need. This will make it easier for your KRONE dealer to process your orders and you will be certain that your machine will be ready for use at the beginning of the next season.

Pos: 116.3 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

115

Before the Start of the New Season

Pos: 116.4 /Ü berschriften/Ü berschriften 1/U-Z/Vor Beginn der neuen Saison @ 4\mod_1211272647559_78.docx @ 82867 @ 1 @ 1

16

Pos: 116.5 /Ü berschriften/Ü berschriften 2/P-T/SSpezi elle Sicher heitshi nweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Before the Start of the New Season

16.1 Special Safety Instructions

Pos: 116.6 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung - R eparatur _Wartung_R einigungs_4 allgemei n EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1

WARNING!

When performing repair, maintenance or cleaning work or in case of technical intervention, drive elements may start moving (caution: cutting discs continue to run).

Effect: Danger to life, injuries or damage to the machine.

• Turn off the PTO shaft.

• Move the machine to the working position and lower it to the ground.

• Switch off the engine of the tractor, remove the ignition key and carry it with you.

• Secure the tractor against accidental start-up and against rolling.

• After the repair, maintenance, cleaning work or technical modifications are completed, mount all protective covers and safety devices properly again.

• Avoid skin contact with oils, greases, cleaning agents and solvents.

• In the event of injuries or burns due to oils, cleaning agents or solvents, contact a physician immediately.

• All other safety instructions must also be followed to avoid injuries and accidents.

Pos: 116.7 /Ü berschriften/Ü berschriften 2/P-T/PProbelauf @ 0\mod_1196782963921_78.docx @ 14908 @ 2 @ 1

16.2 Test run.

Pos: 116.8 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Pr obel auf Ei nzahl M ähwer k muss auf Boden aufliegen @ 11\mod_1223615241207_78.docx @ 148217 @ @ 1

Danger! - Testing the machine after repair, maintenance or cleaning work and after technical intervention.

Effect: Danger to life or serious injuries

• The mowing unit must be in working position

• Do not switch on the drives until the mowing unit is resting on the ground and you are absolutely sure that neither persons, animals nor objects are in the danger zone.

• Start a trial run of the machine only from the driver’s seat.

Pos: 116.9 /BA/Ei nlag erung/EasyC ut / AM M ähwer ke/Vor der Saison ohne Ber eifung @ 3\mod_1204731533226_78.docx @ 72767 @ @ 1

• Lubricate the machine thoroughly. Remove any condensation water which may have collected in the bearings.

• Check oil level in the gearbox(es) and top up if necessary.

• Check all screws to make certain they are tight or retighten them if necessary.

• Check all electrical connection cables and the lighting. Repair or replace if necessary.

• Check the entire setting of the machine and correct if necessary.

• Re-read the operating instructions thoroughly.

Note

Use vegetable oils and greases.

Pos: 116.10 /BA/Ei nlager ung/R eibkupplung/Rei bkupplung lüften vor der Saison @ 3\mod_1204731645242_78.docx @ 72787 @ @ 1

• Vent the friction clutch to release the adhesion of the friction lining.

Pos: 116.11 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

116

Pos: 116.12 /Ü berschriften/Ü berschriften 2/P-T /RRei bkupplung @ 3\mod_1204782451808_78.docx @ 72905 @ 2 @ 1

Before the Start of the New Season

16.3 Friction Clutch

Pos: 116.13 /BA/Sicher hei t/R eibkuppl ung/Achtung - M ani pulati on an der Rei bkupplung @ 3\mod_1204732138258_78.docx @ 72825 @ @ 1

Pos: 116.14 /BA/Ei nlager ung/R eibkupplung/Rei bkupplung entl üften @ 3\mod_1204732297351_78.docx @ 72885 @ @ 1

Caution! - Manipulation of the friction clutch

Effect: Serious damage to the machine

• Manipulation of the overload protection changes the slip torque. This will lead to a loss of warranty claims! Original KRONE spare parts only may be used.

2

1

EC-257-0

Fig. 78

The friction clutch protects the tractor and the machine against damage. It is designed with a permanently adjusted turning torque M clutch (2).

R

. The torque is applied on the housing of the friction

Pos: 116.15 /BA/Inbetriebnahme/EasyC ut/Hinweis R eibkuppl ung @ 11\mod_1223358975938_78.docx @ 145593 @ @ 1

Venting the friction clutch

Tighten the four nuts (1). Block the machine and move the friction clutch manually to the point where it slips through. Loosen the nuts again.

Note - Friction Clutch

Effect: Conserve functionality and increased service life

• The friction clutch (2) must be vented prior to commissioning and once a year prior to harvesting. (See section Before the Start of the New Season "Friction clutch")

Pos: 117 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

117

Special equipment

Pos: 118.1 /Ü berschriften/Ü berschriften 1/P-T/Sonderausstattung @ 2\mod_1202808469779_78.docx @ 61649 @ 1 @ 1

17

Pos: 118.2 /Ü berschriften/Ü berschriften 2/P-T/SSpezi elle Sicher heitshi nweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Special equipment

17.1 Special Safety Instructions

Pos: 118.3 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung - R eparatur _Wartung_R einigungs_4 allgemei n EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1

WARNING!

When performing repair, maintenance or cleaning work or in case of technical intervention, drive elements may start moving (caution: cutting discs continue to run).

Effect: Danger to life, injuries or damage to the machine.

• Turn off the PTO shaft.

• Move the machine to the working position and lower it to the ground.

• Switch off the engine of the tractor, remove the ignition key and carry it with you.

• Secure the tractor against accidental start-up and against rolling.

• After the repair, maintenance, cleaning work or technical modifications are completed, mount all protective covers and safety devices properly again.

• Avoid skin contact with oils, greases, cleaning agents and solvents.

• In the event of injuries or burns due to oils, cleaning agents or solvents, contact a physician immediately.

• All other safety instructions must also be followed to avoid injuries and accidents.

Pos: 118.4 /BA/Sonderausstatung/EasyC ut / AM M ähwer ke/H ochschnittkufen EasyCut @ 3\mod_1204783761105_78.docx @ 72974 @ 2 @ 1

17.2 Adjusting Skids

2

1

3

Pos: 119 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-192-1

Fig. 79

Adjusting skids can be used to increase the cutting height (see chapter entitled "Adjusting the cutting height")

To do this, insert the adjusting skids (3) into the glide skids (2) and screw them in place. The adjusting skids must always be mounted underneath the mowing discs that run next to the mower drum.

118

Pos: 120 /Überschriften/Ü berschriften 1/A-E/Entsorgung der Maschi ne @ 274\mod_1404207309028_78.docx @ 2060455 @ 1 @ 1

Disposal of the machine

18

Pos: 121 /BA/Entsorgung der M aschine/Di e M aschine entsorgen @ 274\mod_1404207434449_78.docx @ 2060544 @ 2 @ 1

Disposal of the machine

18.1

=== Ende der Liste für T extmar ke Inhalt ===

Disposal of the machine

After the service life of the machine has expired, the individual components of the machine must be disposed of properly. The applicable country-specific, current waste disposal guidelines and the legal laws must be observed.

Metal parts

All metal parts must be brought to a metal recycling centre.

The components must be freed from operating fluids and lubricants (gear oil, oil from hydraulic system, ...) before being scrapped.

The operating fluids and lubricants must be brought separately to an environmentally friendly disposal point or recycling centre.

Operating fluids and lubricants

Operating fluids and lubricants (diesel fuel, coolant, gear oil, oil from hydraulic system, ...) must be brought to a disposal point for waste oil.

Synthetic materials

All synthetic materials must be brought to a recycling centre for synthetic materials.

Rubber

Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre.

Electronic scrap

Electronic parts must be brought to a disposal point for electronic scrap.

119

19 Index

A

Abrasion Limit ................................................... 108

Adapting to the tractor ........................................ 49

Adjusting Skids ................................................. 118

Adjusting the Compensation Springs ................. 72

Adjusting the conditioner plate ........................... 80

Adjusting the cutting height ................................ 76

Adjusting the Guards .......................................... 73

Adjustment for Swathing ..................................... 80

After Shearing Off ............................................... 92

Aligning the Cutter Bar ...................................... 100

Ambient Temperature ......................................... 48

Angular gearbox .....................................95, 96, 97

Assembling Guard Cloths ................................... 59

Attached devices ................................................ 14

Attaching Safety Labels and Information Labels 25

B

Before mowing .................................................... 68

Before the Start of the New Season ................. 116

Blade Changing on Cutting Discs ..................... 109

Blade Quick-Fit Device ............................. 105, 111

Blade screw connection .................................... 104

Blade Screw Connection .................................. 110

C

Changing Pulley .................................................. 78

Checking First Fitting .......................................... 63

Checking Spring Retaining Chain ....................... 58

Checking the Cutter Blades and Blade Holder . 102

Clamp and Buffer ................................................ 66

Clutching points .................................................. 50

Commissioning ................................................... 49

Connecting the hydraulic lines ............................ 61

Consumables ...................................................... 48

Contact................................................................ 24

Cutter Blades .................................................... 103

D

Dangers in Case of Non-compliance with the

Safety Instructions .......................................... 13

Detaching the machine ....................................... 71

Deviating Tightening Torques ............................. 87

Dimensions .......................... 42, 43, 44, 45, 46, 47

Direction Information ............................................. 8

Directories and References .................................. 7

Dismounting Retaining Chains ........................... 71

Disposal of the machine

................................ 119

120

Driving and Transport ........................................ 64

F

First installation .................................................. 49

Friction Clutch .................................................. 117

Further applicable documents ............................. 7

G

Gearbox for Top Roller Drive ............................. 98

H

How to use this document ................................... 7

Hydraulic connections .......... 42, 43, 44, 45, 46, 47

Hydraulic system ................................................ 15

Hydraulics .......................................................... 61

I

Identification Plate .............................................. 24

Inadmissible Modes of Operation ...................... 15

Information Required for Questions and Orders 24

Input gearbox ..................................................... 94

Install the PTO shaft .................................... 53, 55

Intended use ...................................................... 11

Intermediate PTO shaft .............................. 87, 114

L

Lighting .............................................................. 64

Lighting connection ............................................ 60

Lower suspension arm ....................................... 51

Lubrication Chart .............................................. 114

M

Machine overview .............................................. 16

Maintenance ................................................ 15, 83

Maintenance – lubrication chart ....................... 113

Maintenance table .............................................. 84

Means of representation ...................................... 8

Notes with information and recommendations 10

Warning signs ................................................. 10

Means of Representation

Figures ............................................................. 8

Metric Thread Screws with Control Thread ....... 85

Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 86

Metric Thread Screws with Fine Thread ............ 86

Minimum tractor requirements .. 42, 43, 44, 45, 46,

47

Mounting and adjusting the relief springs .......... 56

Mounting onto the Tractor .................................. 50

Moving Guards into Transport Position ............. 70

Moving the guards into the working position ..... 69

O

Oil level check and oil change on the cutter bar

...................................................................... 100

Operation ............................................................ 68

P

Parking support ................................................... 70

Periodical Inspection of the Cutting Discs / Blade

Drums ........................................................... 107

Periodical Inspection of the Leaf Springs ......... 106

Personnel Qualification and Training .................. 13

Placing in Storage ............................................. 115

Position of the Adhesive Safety Stickers on the

Machine .......................................................... 26

PTO operation .................................................... 14

PTO shaft ............................................................ 52

Purpose of Use ................................................... 11

R

Re-Ordering Safety Labels and Information Labels

........................................................................ 25

Re-Ordering this Document .................................. 7

Replacing Pulley ................................................. 79

Replacing the linings ......................................... 112

Rotary hub with shear fuse (optional) ................. 88

S

Safety .................................................................. 11

Safety Instructions and Accident Prevention

Regulations ..................................................... 12

Safety-conscious work practices ........................ 13

Scope of Document .............................................. 8

Service life of the machine

............................. 11

Setting Conditioner Speed ................................. 77

Setting the Distance of the Rollers .................... 82

Settings .............................................................. 72

Spare Parts ........................................................ 83

Special equipment ........................................... 118

Start-up .............................................................. 54

T

Target group of this document ............................. 7

Technical data .................................................... 42

Technical data dimensions .. 42, 43, 44, 45, 46, 47

Technical data hydraulic connections ... 42, 43, 44,

45, 46, 47

Technical data minimum tractor requirements . 42,

43, 44, 45, 46, 47

Technical Data of the Machine .......................... 42

Telescopic upper suspension arm ..................... 76

Tensioning Belt Drive ................................... 79, 99

Tensioning Guard Cloth ..................................... 69

Term ..................................................................... 8

Test run ............................................................ 116

Test run .............................................................. 83

Tightening torques ............................................. 85

U

Unauthorised Conversion/Modification and Spare

Parts Production ............................................ 15

Universally-Jointed Drive Shaft ........................ 113

W

Wide spreading .................................................. 81

121

Maschinenfabrik

Bernard Krone GmbH & Co. KG

Heinrich-Krone-Straße 10, D-48480 Spelle

Postfach 11 63, D-48478 Spelle

Phone +49 (0) 59 77/935-0

Fax +49 (0) 59 77/935-339

Internet: http://www.krone.de

eMail: [email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement

Table of contents