Krone EasyCut 28, EasyCut 28 P, EasyCut 28 M, EasyCut 32, EasyCut 32 P,EasyCut 32 M Operating Instructions


Add to my manuals
80 Pages

advertisement

Krone EasyCut 28, EasyCut 28 P, EasyCut 28 M, EasyCut 32, EasyCut 32 P,EasyCut 32 M Operating Instructions | Manualzz

EasyCut 28

EasyCut 28 P

EasyCut 28 M

(from serial no.: 785 000)

Order no.: 150 000 015 03 us

Disc Mower

EasyCut 32

EasyCut 32 P

EasyCut 32 M

06.06.2016

Table of Contents

Pos: 1 /Ü berschriften/Ü berschriften 1/F-J/Inhaltsverzeichnis @ 31\mod_1251969952727_78.docx @ 302165 @ 1 @ 1

1

Pos: 2 /BA/Inhaltsverzeichnis Spr achenneutr al @ 10\mod_1221574899104_0.docx @ 135495 @ @ 1

Table of Contents

1 Table of Contents ................................................................................................................................... 2

2 Introduction ............................................................................................................................................. 5

2.1

Purpose of Use ................................................................................................................................... 5

2.2

Validity ................................................................................................................................................ 5

2.2.1

Contact for KRONE NORTHAMERICA ...................................................................................... 5

2.3

Identification Plate .............................................................................................................................. 6

2.4

Information Required for Questions and Orders ................................................................................ 6

2.5

Intended use ....................................................................................................................................... 7

2.6

Technical data .................................................................................................................................... 7

3 Safety ....................................................................................................................................................... 8

3.1

Identifying Symbols in the Operating Instructions .............................................................................. 8

3.2

Identification of the hazard warnings.................................................................................................. 8

3.3

Safety Instructions and Accident Prevention Regulations ................................................................. 9

3.3.1

Personnel Qualification and Training ........................................................................................ 10

3.3.2

Dangers in Case of Non-compliance with the Safety Instructions ............................................ 10

3.3.3

Safety-conscious work practices ............................................................................................... 10

3.4

Attached devices .............................................................................................................................. 11

3.5

PTO operation .................................................................................................................................. 11

3.6

Hydraulic system .............................................................................................................................. 12

3.7

Maintenance ..................................................................................................................................... 12

3.8

Unauthorised Conversion/Modification and Spare Parts Production ............................................... 13

3.9

Inadmissible Modes of Operation ..................................................................................................... 13

3.10

Introduction ....................................................................................................................................... 13

3.11

Position of the Adhesive Safety Stickers on the Machine ................................................................ 14

4 Commissioning ..................................................................................................................................... 18

4.1

Special Safety Instructions ............................................................................................................... 18

4.2

First installation ................................................................................................................................ 18

4.3

Fitting the guard cloths ..................................................................................................................... 19

4.4

Installation of Weiste triangle ........................................................................................................... 20

4.5

Preparation on the front-mounted disc mower ................................................................................. 20

4.6

Lighting ............................................................................................................................................. 21

5 Start-up .................................................................................................................................................. 22

5.1

Preparations on tractor ..................................................................................................................... 22

5.2

Mounting onto the Tractor ................................................................................................................ 23

5.2.1

Lower suspension arm .............................................................................................................. 24

5.3

Checking the First fitting ................................................................................................................... 25

5.4

PTO shaft ......................................................................................................................................... 26

5.4.1

Length adjustment ..................................................................................................................... 26

5.5

Install the PTO shaft ......................................................................................................................... 27

5.6

Mounting and Adjusting the Relief Springs ...................................................................................... 28

5.7

Trial run after first installation ........................................................................................................... 28

5.8

Lighting connection .......................................................................................................................... 29

5.9

Hydraulics ......................................................................................................................................... 30

5.9.1

Special Safety Instructions ........................................................................................................ 30

5.9.2

Connecting the hydraulic lines .................................................................................................. 30

2

Table of Contents

6 Driving and Transport .......................................................................................................................... 32

6.1

Lighting ............................................................................................................................................. 32

6.2

Clamp and Buffer ............................................................................................................................. 33

7 Operation ............................................................................................................................................... 34

7.1

Before mowing ................................................................................................................................. 34

7.2

Moving the guards into the working position .................................................................................... 35

7.3

Detaching the machine..................................................................................................................... 36

7.4

Removing the compensation spring(s)............................................................................................. 36

8 Settings ................................................................................................................................................. 38

8.1

Compensation Spring(s) .................................................................................................................. 39

8.2

Adjusting the Compensation Springs ............................................................................................... 40

8.3

Adjusting the cutting height .............................................................................................................. 41

8.3.1

Telescopic upper suspension arm ............................................................................................ 41

8.4

Setting of the V-belt Tension ............................................................................................................ 42

9 Maintenance .......................................................................................................................................... 43

9.1

Special Safety Instructions ............................................................................................................... 43

9.1.1

Test run ..................................................................................................................................... 43

9.2

Spare Parts ...................................................................................................................................... 44

9.3

Tightening torques ............................................................................................................................ 44

9.3.1

Metric Thread Screws with Control Thread............................................................................... 44

9.3.2

Metric Thread Screws with Fine Thread ................................................................................... 45

9.3.3

Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 45

9.3.4

Deviating Tightening Torques ................................................................................................... 46

9.4

Filling Quantities and Lubrication Designations for Gearboxes ....................................................... 47

9.4.1

Oil Level Check and Oil Change Intervals (Gearboxes) ........................................................... 47

9.5

Angular gearbox ............................................................................................................................... 48

9.5.1

Front Mowing Unit (CV+CRI) .................................................................................................... 48

9.6

Mower Drive Gearbox ...................................................................................................................... 49

9.7

Oil level check and oil change on the cutter bar .............................................................................. 50

9.7.1

Oil change ................................................................................................................................. 50

9.7.2

Checking the oil level ................................................................................................................ 50

9.7.3

Aligning the Cutter Bar .............................................................................................................. 50

9.8

Checking the Cutter Blades and Blade Holder ................................................................................ 52

9.8.1

Cutter Blades ............................................................................................................................ 52

9.8.2

Blade screw connection ............................................................................................................ 53

9.8.3

Blade Quick-Fit Device.............................................................................................................. 54

9.8.4

Checking the Material Thickness of the Retaining Bolts ........................................................... 54

9.8.4.1

Checking the material thickness of the retaining bolts ...................................................... 55

9.8.5

Periodical Inspection of the Leaf Springs.................................................................................. 56

9.8.6

Checking the Material Thickness of the Leaf Springs ............................................................... 56

9.8.6.1

Checking the material thickness of the leaf springs .......................................................... 57

9.8.7

Periodical Inspection of the Cutting Discs / Blade Drums ......................................................... 58

9.8.8

Abrasion Limit ........................................................................................................................... 59

9.9

Blade Changing on Cutting Discs .................................................................................................... 60

9.9.1

Blade Screw Connection ........................................................................................................... 61

9.9.2

Blade Quick-Fit Device.............................................................................................................. 62

9.10

Replacing the linings ........................................................................................................................ 63

9.11

Rotary hub with shear fuse (optional) .............................................................................................. 64

3

Table of Contents

9.11.1

After Shearing Off ..................................................................................................................... 66

10 Maintenance – lubrication chart ......................................................................................................... 68

10.1

Special Safety Instructions ............................................................................................................... 68

10.2

PTO shaft ......................................................................................................................................... 68

10.3

Lubrication Chart .............................................................................................................................. 69

11 Placing in Storage ................................................................................................................................ 70

12 Before the Start of the New Season ................................................................................................... 71

12.1

Special Safety Instructions ............................................................................................................... 71

12.2

Test run. ........................................................................................................................................... 71

13 Special equipment ................................................................................................................................ 72

13.1

Special Safety Instructions ............................................................................................................... 72

13.2

Conversion to narrower swathing ..................................................................................................... 73

13.3

Conversion for mowing steep slopes ............................................................................................... 75

14 Disposal of the machine ...................................................................................................................... 76

14.1

Disposal of the machine ................................................................................................................... 76

15 Index ...................................................................................................................................................... 77

Pos: 3 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

4

Pos: 4.1 /BA/Ei nleitung/Ei nleitung @ 0\mod_1195562498677_78.docx @ 416 @ 1 @ 1

Introduction

2 Introduction

Pos: 4.2 /Ü berschriften/Ü berschriften 2/U-Z/VVer wendungszweck @ 1\mod_1201707246738_78.docx @ 54055 @ 2 @ 1

These operating instructions contain fundamental instructions. These must be observed in operation and maintenance. For this reason, these operating instructions must be read by operating personnel before commissioning and use, and must be available for easy reference.

Follow both the general safety instructions contained in the section on safety and the specific safety instructions contained in the other sections.

2.1 Purpose of Use

Pos: 4.3 /BA/Ei nleitung/EasyC ut/Verwendungszweck Mäher @ 3\mod_1204547495418_78.docx @ 70590 @ @ 1

Pos: 4.4 /BA/Ei nleitung/Gültigkeit/EasyC ut /EasyC ut 28/32 28/32P 28M @ 10\mod_1221642027181_78.docx @ 135781 @ 2 @ 1

The EasyCut disc mower is used for cutting crops growing on the ground (except maize).

2.2 Validity

These operating instructions apply to disc mowers of the series:

EasyCut 28; EasyCut 28 P; EasyCut 28 M; EasyCut 32 ; EasyCut 32 P; EasyCut 32 M

Pos: 4.5 /Ü berschriften/Ü berschriften 3/A- E/A/Ansprechpar tner KR ON E-NORTH AMERIC A @ 10\mod_1221053854903_78.docx @ 131870 @ 3 @ 1

2.2.1

Pos: 4.6 /BA/Adressen/Adr esse KRON E N orth America @ 417\mod_1453355357015_78.docx @ 2921495 @ @ 1

Contact for KRONE NORTHAMERICA

Mailing address

Krone North America, Inc.

P.O. Box 18880

Memphis, TN 38181-0880

USA

Phone

Fax

E-mail

Internet

Pos: 4.7 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Physical address

Krone North America, Inc.

3363 Miac Cove

Memphis, TN 38118

USA

+1 901 842-6011

+1 901 842-6016 [email protected] www.krone-northamerica.com

5

Introduction

Pos: 4.8 /Ü berschriften/Ü berschriften 2/K- O/KKennzeichnung @ 0\mod_1195564622099_78.docx @ 496 @ 2 @ 1

2.3 Identification Plate

Pos: 4.9 /BA/Ei nleitung/Kennzeichnung/EasyC ut/Kennzeichnung EasyC ut 28/32 28/32P 28M @ 10\mod_1221642592431_78.docx @ 135803 @ @ 1

1

Fig. 1

The machine data are specified on the type plate (1). It is attached to the carrying bar.

Pos: 4.10 /BA/Einl eitung/Kennzeichnung/Angaben für Anfr age und Bestellungen_M aschnr . (2015- 11- 04 15:38:15) @ 9\mod_1220507505930_78.docx @ 126110 @ 2 @ 1

2.4 Information Required for Questions and Orders

Pos: 4.11 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Year

Mach. No.

Type

Note

The entire identification plate represents a legal document and should not be altered or rendered illegible!

When asking questions concerning the machine or ordering spare parts, be sure to provide type designation, machine number and the year of manufacture of the relevant machine: To ensure that these data are always available, we recommend that you enter them in the fields above.

Note

Authentic KRONE spare parts and accessories authorised by the manufacturer help to ensure safety. The use of spare parts, accessories or additional equipment not manufactured, tested or approved by KRONE will exclude any liability for consequential damage.

6

Pos: 4.12.1 /Überschriften/Überschriften 2/A-E/B/Besti mmungsgemäß e Ver wendung @ 103\mod_1332169199326_78.docx @ 940071 @ 2 @ 1

Ver

Introduction

2.5 Intended use

Pos: 4.12.2 /BA/Einl eitung/Besti mmungsgemäßer Gebrauch/EasyCut/Bestimmungsgemäß er Gebrauch (Ei nzahl) @ 3\mod_1204548357809_78.docx @ 70671 @ @ 1

The disc mower is built exclusively for customary use in agricultural work (intended use).

Pos: 4.12.3 /BA/Einl eitung/Besti mmungsgemäßer Gebrauch/Nicht besti mmungsgemäß @ 103\mod_1332171672294_78.docx @ 940272 @ @ 1

Pos: 4.13 /BA/Einl eitung/T echnische D aten/Technische Daten mit 2. Ü berschrift @ 0\mod_1195566374865_78.docx @ 594 @ 2 @ 1

Unauthorised modifications to the machine may have a negative effect on the machine characteristics or safe and reliable use of the machine or may interfere with proper operation.

Unauthorised modifications shall therefore release the manufacturer of any liability for consequential damage.

2.6 Technical data

All information, illustrations and technical data in these operating instructions correspond to the latest state at the time of publication. We reserve the right to make design changes at any time and without notification of reasons.

Type

Working width

Transport width

Number of mowing discs

Number of mower drums

Acreage

Power consumption

PTO speed

Service weight

* Optional

Type

Working width

Transport width

Number of mowing discs

Number of mower drums

Acreage

Power consumption

PTO speed

Service weight

* Optional

Pos: 5 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

[mm]

[mm]

[ha/h]

[kW/HP]

[rpm]

[kg]

[mm]

[mm]

[ha/h]

[kW/HP]

[rpm]

[kg]

EasyCut 28

2710

2565

4

2

3 - 3.5

44 / 60

1000

680

EasyCut 32

3140

3000

5

2

3.5 - 4

51 / 70

1000

840

EasyCut 28 P

2710

2565

4

2

3 - 3.5

44 / 60

1000

700

EasyCut 32 P

3140

3000

5

2

3.5 – 4

51 / 70

1000

860

EasyCut 28M

2710

2565

4 (2*)

4

3 - 3.5

40 / 55

1000

520

EasyCut 32 M

3140

3000

5 (3*)

4

3.5 – 4

44 / 60

1000

640

7

Safety

Pos: 6.1 /Ü berschriften/Ü berschriften 1/P-T /Sicher heit @ 0\mod_1195566748646_78.docx @ 635 @ 1 @ 1

3 Safety

Pos: 6.2 /BA/Sicher heit/6. Ü berarbeitete Warnhinweise/Kennzeichnung von Hi nweisen i n der Betriebsanl eitung Ei nführungstext ( 2012-07-27 09:59:06) @ 0\mod_1195637804826_78.docx @ 1098 @ 2 @ 1

3.1 Identifying Symbols in the Operating Instructions

The safety instructions contained in this manual which could result in personal injury if not followed are identified by the general danger sign:

Pos: 6.3 /BA/Sicher heit/6. Ü berarbeitete Warnhinweise/Kennzeichnung der Gefahrenhi nweise ( 2012-07-26 15:10:30) @ 28\mod_1250244370070_78.docx @ 274714 @ 2 @ 1

3.2 Identification of the hazard warnings

Danger!

DANGER! - Type and source of the hazard!

Effect: Danger to life or serious injuries.

• Measures for hazard prevention

Warning !

WARNING! - Type and source of the hazard!

Effect: Injuries, serious material damage.

• Measures for hazard prevention

Caution!

CAUTION! - Type and source of the hazard!

Effect: Property damage

• Measures for risk prevention.

Pos: 6.4 /BA/Sicher heit/6. Ü berarbeitete Warnhinweise/Allgemeine F unkti onshi nweise ( 2012-07-26 15:24:39) @ 0\mod_1196869714452_78.docx @ 15185 @ @ 1 General function instructions are indicated as follows:

Note!

Note - Type and source of the note

Effect: Economic advantage of the machine

• Actions to be taken

Instructions which are attached to the machine need to be followed and kept fully legible.

Pos: 6.5 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

8

Pos: 6.6.1 /BA/Sicher hei t/Sicherheits- und Unfall verhütungs-Vorschriften Swadr o_Ladewagen_EasyCut @ 73\mod_1308298589597_78.docx @ 655493 @ 2 @ 1

Safety

3.3 Safety Instructions and Accident Prevention Regulations

Pos: 6.6.2 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

1 Please follow all generally applicable safety and accident prevention regulations in addition to the safety instructions contained in these operating instructions!

2 The attached warning and safety signs provide important information for safe operation. Pay attention to these for your own safety!

3 When using public roads, make sure to observe the applicable traffic regulations!

4 Make sure that you are familiar with all equipment and controls as well as with their functions before you begin working with the machine. It is too late to learn this when you are using the machine for work!

5 The user should wear close fitting clothes. Avoid wearing loose or baggy clothing.

6 Keep the machine clean to prevent the danger of fire!

7 Before starting or moving the machine, make certain that nobody is in the vicinity of the machine! (Watch for children!) Make sure that you have a clear view!

8 Carrying passengers during operation and transport on the working implement is not permitted.

9 Couple implements correctly! Attach and secure implements to specified devices only!

10 When attaching or detaching implements, place the supporting devices in the correct positions!

11 Use extreme caution when attaching or detaching implements onto or from the tractor!

12 Always attach ballast weights properly to the fixing points provided!

13 Observe permitted axle loads, gross weight and transport dimensions!

14 Check and attach transport equipment, such as lighting, warning devices and protective equipment!

15 Actuating mechanisms (cables, chains, linkages etc.) for remote controlled devices must be positioned in such a way that no movements are unintentionally triggered in any transport or working positions.

16 Ensure that implements are in the prescribed condition for on-road travel and lock them in place in accordance with the manufacturer's instructions!

17 Never leave the driver's seat when the vehicle is moving!

18 Always drive at the correct speed for the prevailing driving conditions! Avoid sudden changes in direction when travelling uphill or downhill or across a gradient!

19 Hitched implements and ballast weights affect the driving, steering and braking response of the machine. Make sure that you are able to brake and steer the machine as required!

20 Take into account the extension radius and/or inertia of an implement when turning corners!

21 Start up implements only when all safety devices have been attached and set in the required position!

22 Keep safety equipment in good condition. Replace missing or damaged parts.

23 Keep clear of the working range of the machine at all times!

24 Do not stand within the turning and swivel range of the implement!

25 Never operate the hydraulic folding frames if anyone is inside the swivel range!

26 Parts operated by external power (e.g. hydraulically) can cause crushing and shearing injuries!

27 Before leaving the tractor, lower the implement onto the ground, apply the parking brake, switch off the engine and remove the ignition key!

9

Safety

Pos: 6.6.3 /BA/Sicher hei t/Personalqualifi kation und -schulung @ 0\mod_1195639383185_78.docx @ 1136 @ 3 @ 1

3.3.1 Personnel Qualification and Training

The machine may be used, maintained and repaired only by persons who are familiar with it and have been instructed about the dangers connected with it. The operator must define areas of responsibility and monitoring of personnel. Should personnel lack the required knowledge, they must receive the required training and instruction. The operator must ensure that the contents of these operating instructions have been fully understood by personnel.

Repair work not described in these operating instructions should only be performed by authorised service centres.

Pos: 6.6.4 /BA/Sicher hei t/Gefahren bei Ni chtbeachtung der Sicherheitshinweise @ 0 \mod_1195639434013_78.docx @ 1155 @ 3 @ 1

3.3.2 Dangers in Case of Non-compliance with the Safety Instructions

Pos: 6.6.5 /BA/Sicher hei t/Sicherheitsbewusstes Ar bei ten_Teil 1 @ 0\mod_1195639792576_78.docx @ 1174 @ 3 @ 1

Failure to follow the safety instructions could result in personal injury and environmental hazards as well as damage to the machine. If the safety instructions are not respected, this could result in the forfeiture of any claims for damages.

Failure to follow the safety instructions could result, for example

, in the following hazards:

• Endangering of persons due to not protected working areas.

• Breakdown of important machine functions

• Failure of prescribed methods for repair and maintenance

• Endangering of persons due to mechanical and chemical effects

• Damage to the environment due to leaking hydraulic oil

3.3.3 Safety-conscious work practices

Pos: 6.6.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Always observe the safety instructions set out in these operating instructions, all existing accident prevention rules and any internal work, operating and safety rules issued by the operator.

The safety and accident prevention regulations of the responsible professional associations are binding.

The safety instructions provided by the vehicle manufacturer should also be observed.

Observe the applicable traffic laws when using public roads.

Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep emergency numbers for doctors and fire brigade close to the telephone.

10

Pos: 6.6.7 /BA/Sicher hei t/Angebaute Geräte/Geräte ang ebaut EasyCut @ 3\mod_1204552588996_78.docx @ 70752 @ 2 @ 1

3.4

Safety

Attached devices

1 Use extreme caution when attaching or detaching implements onto or from the tractor!

2 Couple the respective application devices to the appropriate couplings (e.g. three-point suspension) only and secure them in a way (transport, use) that excludes inadvertent lifting or lowering of the device.

3 When using three-point linkage, the attachment categories of the tractor and the device

(e.g. PTO speed, hydraulic system) must be coordinated!

4 When using the outside controls for the three-point linkage, do not step between the tractor and the device (risk of injury)!

Pos: 6.6.8 /BA/Sicher hei t/Z apfwell enbetrieb Tr aktor @ 0\mod_1199699899350_78.docx @ 33264 @ 2 @ 1

3.5 PTO operation

1  Use only PTO shafts specified by the manufacturer!

2  The guard tube and guard cone of the PTO shaft and the PTO guard must be attached and in good working condition (on the implement side, too)!

3  Make sure that the required tube covers are in place for PTO shafts in transport and working position!

4  Before installing or detaching PTO shafts, disengage the PTO, switch off the engine and remove the ignition key!

5  When using PTO shafts with an overload safety or free-running coupling which are not shielded by the guard on the tractor, mount the overload safety or free-running coupling on the implement side!

6  Always make sure that the PTO shaft is properly installed and secured!

7  Attach chains to prevent the PTO shaft guard from rotating with the shaft!

8  Before switching on the PTO, make sure that the selected PTO speed of the tractor matches the permissible implement speed!

9  Before switching on the PTO shaft make sure that no person is in the danger zone of the device!

10  Never switch on the PTO if the engine is switched off!

11  No one should be in the vicinity of the rotating PTO or PTO shaft when the PTO is in use.

12  Always switch off the PTO shaft when the angle is too large or the PTO shaft is not required!

13 Caution! After disengaging the PTO danger due to the flywheel running on! Keep away from the implement during this time. The machine may be worked on only if it is completely at standstill and if the flywheel is secured by the parking brake.

14  Cleaning, lubricating or adjusting PTO driven implements or the PTO shaft only with PTO disengaged, engine switched off and ignition key withdrawn! Secure the fly-wheel with the parking brake.

15  Place the disconnected PTO shaft onto the support provided!

16  After detaching the PTO shaft, attach the protective cover to the PTO end!

17  If damage occurs, correct this immediately before using the implement!

Pos: 6.6.9 /BA/Sicher hei t/Z apfwell enbetrieb Z usatz @ 2\mod_1203524761314_78.docx @ 66513 @ @ 1

Pos: 6.6.10 /Layout M odule /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The instructions of the manufacturer must be observed with regard to the PTO shaft. (separate operating instructions)

11

Safety

Pos: 6.6.11 /BA/Sicherheit/H ydr auli kanlage @ 2\mod_1203503691986_78.docx @ 66225 @ 2 @ 1

3.6 Hydraulic system

1  The hydraulic system is pressurised!

2  When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are connected as specified!

3  When connecting the hydraulic hoses to the tractor hydraulics, make sure that the hydraulics of both the tractor and the implement have been depressurized!

4  In the case of hydraulic connections between tractor and machine, the coupling sleeves and plugs should be marked to ensure a proper connection! If the connectors are interchanged, the function will be reversed (e. g. raising/lowering) - Risk of accident!

5  When searching for leaks, use suitable aids to avoid the risk of injury!

6  Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause serious injury! Seek medical help immediately should injuries occur! Danger of infection!

7  Before working on the hydraulic system, depressurise the system and switch off the engine!

Pos: 6.6.12 /BA/Sicherheit/H ydr auli kanlage Zusatz Alter ung der H ydraulikschl auchl eitung en @ 3\mod_1204552944856_78.docx @ 70772 @ @ 1

8 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The new hoses must fulfill the technical requirements set by the manufacturer of the implement!

Pos: 6.6.13 /BA/Sicherheit/Wartung/Wartung M äher mit Gasspeicher+ Auswechsel n von Ar beitswer kzeugen @ 0 \mod_1195647075607_78.docx @ 1442 @ 2 @ 1

3.7 Maintenance

Pos: 6.6.14 /Layout M odule /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

1 Always make certain that the drive and the engine are switched off before doing any repairs, maintenance or cleaning! - Remove the ignition key!

2 Regularly check that nuts and bolts are properly seated and tighten if necessary!

3 When carrying out maintenance work on a raised mowing unit, always use suitable means to secure it against falling.

4 When replacing working tools with cutting edges, use suitable tools and gloves!

5 Oils, greases and filters must be disposed of correctly!

6 Always disconnect the power supply before working on the electrical system!

7 If protective devices and guards are subject to wear, check them regularly and replace them in good time!

8 When performing electrical welding work on the vehicle and mounted devices, turn the power supply off at main battery switch or disconnect generator cable and battery!

9 Replacement parts must at least comply with the technical requirements set by the manufacturer of the implements! This is guaranteed by original KRONE spare parts!

10 Only use nitrogen for filling pneumatic accumulators - risk of explosion!

12

Pos: 6.6.15 /BA/Sicherheit/Eigenmächtiger U mbau und Ersatzteilherstellung @ 1\mod_1201937705539_78.docx @ 55745 @ 2 @ 1

Safety

3.8

Pos: 6.6.16 /BA/Sicherheit/Unzul ässige Betriebsweisen @ 11\mod_1223357699923_78.docx @ 145527 @ 2 @ 1

Unauthorised Conversion/Modification and Spare Parts Production

Conversions or modifications of the machine are permitted only with prior consultation with the manufacturer. Original spare parts and accessories authorised by the manufacturer help to ensure safety. Use of other parts may void liability for resulting damage.

3.9 Inadmissible Modes of Operation

Pos: 6.7 /BA/Sicher heit/EasyCut/Sicherheit Einführung EasyC ut @ 3\mod_1204553763950_78.docx @ 70812 @ 2 @ 1

The operating safety of the delivered machine is guaranteed only when it is used as intended in compliance with the introductory section "Intended use" of the operating instructions. The limit values listed in the data charts should not be exceeded under any circumstances.

3.10 Introduction

The disc mower is equipped with all safety devices (protective devices). However, it is not possible to eliminate all potential hazards on this machine as this would impair its full functional capability. Hazard warnings are attached to the machine in the relevant areas to warn against any dangers. The safety instructions are provided in the form of so-called warning pictograms.

Important information on the position of these safety signs and what they mean is given below!

Pos: 6.8 /BA/Sicher heit/2. Vor angestellte War nhi nweise/Warnung - Beschädigte oder unl esbar e War nbil dzeichen @ 120\mod_1343305789479_78.docx @ 1099853 @ @ 1

Pos: 6.9 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

WARNING!

Danger of injury on machine parts if danger zones have not been marked when warning pictograms are missing, damaged or illegible.

Danger of injury due to dangerous parts and other residual risks as users or third parties enter the danger area or reach into it as they are not aware of the danger.

• Immediately replace damaged or illegible labels.

• Following repair work, always attach appropriate adhesive safety labels to all the replaced, modified or repaired components.

• Never clean areas carrying an adhesive safety label using a high-pressure cleaner.

Familiarise yourself with the statement of the warning pictograms. The adjacent text and the selected location on the machine provide information on the special danger spots on the machine.

13

Safety

Pos: 6.10 /Überschriften/Überschriften 2/K-O/LLage der Sicher hei tsaufkl eber an der M aschine @ 0\mod_1195634967326_78.docx @ 1020 @ 2 @ 1

3.11 Position of the Adhesive Safety Stickers on the Machine

Pos: 6.11 /Abkürzungen /Abkürzungen sprachneutr al/EasyC ut/EasyC ut 28, EasyC ut 28 P, EasyC ut 32, EasyC ut 32 P @ 10\mod_1221658395259_0.docx @ 136073 @ @ 1

EasyCut 28, EasyCut 28 P, EasyCut 32, EasyCut 32 P

4 5 10 11

7

9

1.1

1.2

6

8

9

2

4 5 10 11

Fig. 2

4 5 9 11

4 5 9 11

4 9

EC-238-1

1.1

2 6

1.2

4 9 4 5 9 10

7 4 5 9 10

8

5

Fig. 3

14

1.1)

CAUTION

Max. PTO speed

1000 RPM

27 004 599 0

Best.-Nr. 27 004 599 0 (1x)

2)

CAUTION

To a v oid s e rious injury or de a th

- Read and unders tand operator´s m anual before operating equipm ent.

- Lower implement, stop tractor engine and remove key before leav ing operator´s platform .

- Keep all s hields and guards in place.

- Keep hands feet and c lothing away from m ov ing parts .

- Keep riders off the m ac hine.

- Make certain every one is clear of the machine before starting trac tor engine and s tarting.

- Do not allow unqualified operator to run equipm ent.

- Do not operate equipm ent in trans port pos ition.

- Never lubricatem, adjust, unclog or service the equipment with trac tor engine is running.

- Wait for all movement to stop before opening shield or servicing m ac hine.

- Nev er work underneath equipm ent without s ec urely s upporting.

27 002 054 0

Order No. 27 002 054 0 (1x)

5)

Order No. 27 002 058 0 (4x)

7)

1.2)

CAUTION

The operating pressure of the hydraulic system must not exceed

200 ba r.

27 004 598 0

Best.-Nr. 27 004 598 0 (1x)

4)

DANGER

Blade can cause serious injury or de a th.

- Stay c lear of m ac hine while in operation.

- Keep dis c harge c hute and s hields in plac e.

Order No. 27 002 056 0 (4x)

6)

Order No. 939 106-3

(1x)

Safety

8)

Order No. 949 228 0 (2x)

Order No. 949 229 0 (1x)

15

Safety

7

8

4 5 10 11

9

1.1

1.2

6

9

2

4 5 10 11

Fig. 4

4 5 9 11

4 5 9 11

4 9

EC-238-1

1.1

2 6

1.2

4 9 4 5 9 10

7 4 5 9 10

8

5

Fig. 5

16

9)

Warning

To avoid personal injury.

Never put your hand into the danger area as parts may be moving.

27 002 057 0

Order No. 27 002 057 0 (4x)

11)

Order No. 27 002 055 0 (4x)

Pos: 7 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

10)

Order No. 27 002 060 0 (2x)

Safety

17

Commissioning

Pos: 8.1 /Ü berschriften/Ü berschriften 1/A- E/Erstinbetriebnahme @ 0\mod_1196314201498_78.docx @ 5855 @ 1 @ 1

4

Pos: 8.2 /Ü berschriften/Ü berschriften 2/P-T /SSpezi elle Sicher heitshi nweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Commissioning

4.1 Special Safety Instructions

Pos: 8.3 /BA/Sicher heit/7. Gefahrenhinweise al t/Ei nstellar bei ten / Ei nstellungen/Gefahr - Einstell arbeiten g ezog ene M aschinen (2013- 12- 18 10:47:30) @ 0\mod_1199717011038_78.docx @ 33980 @ @ 1

Danger! - Unexpected movements of the machine

Effect: Danger to life or serious injuries.

• Setting tasks must only be performed when the drive is switched off and the engine is at a standstill!

• Switching off the engine

• Remove the ignition key.

• Secure the machine against the possibility of rolling back.

Pos: 8.4 /Ü berschriften/Ü berschriften 2/A- E/EErstmontage @ 1\mod_1202226261982_78.docx @ 58270 @ 2 @ 1

4.2 First installation

Pos: 8.5 /BA/Sicher heit/7. Gefahrenhinweise al t/Gefahr - F ehl erhafter Z usammenbau @ 1\mod_1202224212591_78.docx @ 58171 @ @ 1

Danger! - Incorrect assembly

Effect: Danger to life, serious injuries or serious damage to the machine.

• Only authorised service centres may assemble the machine.

• The machine must be assembled with special care.

• Always heed the applicable accident prevention regulations.

• Use only safe and sufficiently dimensioned lifting equipment and load-securing equipment.

• The machine may be taken into operation only after all the safety devices have been installed.

• If unauthorised modifications are made to the machine, the manufacturer is released from liability for any resulting damage.

Pos: 8.6 /BA/Sicher heit/7. Gefahrenhinweise al t/Gefahr - F ehl ende Schutztücher Erstinbetriebnahme @ 3\mod_1204628072251_78.docx @ 71025 @ @ 1

Danger! - Missing guard cloths

Pos: 8.7 /Abkürzung en /Abkürzungen spr achneutral/EasyCut/EasyCut 28 M @ 10\mod_1221658268900_0.docx @ 136051 @ @ 1

Effect: Lebensgefahr, schwere Verletzungen oder schwere Schäden an der Maschine.

• Before starting up the machine for the first time, install all supplied guard cloths on the machine.

Pos: 8.8 /BA/Ersti nbetriebnahme/Erstmontage @ 1\mod_1202224111998_78.docx @ 58190 @ @ 1

(EasyCut 28 M)

The document "Assembly Instructions" describes how to install the device for the first time.

Pos: 8.9 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

18

Pos: 8.10 /Überschriften/Überschriften 2/P-T/SSchutztücher monti eren @ 35\mod_1257494335719_78.docx @ 329260 @ 2 @ 1

4.3 Fitting the guard cloths

Pos: 8.11 /Abkürzungen /Abkürzungen sprachneutr al/EasyC ut/EasyC ut 28, EasyC ut 28 P, EasyC ut 32, EasyC ut 32 P @ 10\mod_1221658395259_0.docx @ 136073 @ @ 1

EasyCut 28, EasyCut 28 P, EasyCut 32, EasyCut 32 P

Pos: 8.12 /BA/Ersti nbetriebnahme/EasyC ut/Schutztücher/Schutztücher monti eren EC 28/32 (P) Bild @ 10\mod_1221658764493_78.docx @ 136118 @ @ 1

4

Commissioning

Fig. 6

Pos: 8.13 /BA/Ersti nbetriebnahme/EasyC ut/Schutztücher/Schutztücher monti ert EC 28/32 (P) @ 10\mod_1221658896868_78.docx @ 136140 @ @ 1

Pos: 8.14 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Item Part No.

1 904 731

2 910 603

3 908 706

4 900 614

Name

Square coach bolt M 8 x 20

Washer 8.4 x 24 x 2

Hex nut NM 8

Hex screw M 8 x 20

EC 28 EC 32

33

43

38

5

34

44

39

5

19

Commissioning

Pos: 8.15 /BA/Ersti nbetriebnahme/EasyC ut/Anbau Weiste-Dreieck @ 3\mod_1204640890345_78.docx @ 71160 @ 2 @ 1

4.4 Installation of Weiste triangle

1

AFL 245-0-007

Fig. 7

Pos: 8.16 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Warnung Anbau des Kupp eldr eiecks ( Weiste Dr eieck) @ 3\mod_1204638378407_78.docx @ 71102 @ @ 1

Warning - Installation of the triangle linkage (Weiste triangle)

Pos: 8.17 /BA/Ersti nbetriebnahme/EasyC ut/Anbau Weiste-Dreieck T ext @ 3\mod_1204638631735_78.docx @ 71179 @ @ 1

Effect: Danger to life or serious injuries. Considerable damage to the machine

Observe manufacturer's operating instructions for the triangle linkage!

For the installation of the front-mounted disc mower, a Weiste triangle (1) is attached to the front hydraulics. Adjust the top suspension arm in such a way that the triangle is inclined slightly forward.

Pos: 8.18 /Überschriften/Überschriften 2/U-Z/VVor bereitung am Fr ontschei benmäher @ 35\mod_1257497246000_78.docx @ 329285 @ 2 @ 1

4.5 Preparation on the front-mounted disc mower

Pos: 8.19 /BA/Ersti nbetriebnahme/EasyC ut/Vorbereitung am Frontscheibenmäher EC 28/32 28P/32P 28M @ 10 \mod_1221659810103_78.docx @ 136162 @ @ 1

Pos: 8.20 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-1-005

Fig. 8:

• Push the PTO shaft (3) with full protection (4) onto the PTO shaft end of the machine.

• The safety mechanism must engage

• Secure the PTO shaft guard (2) against turning with pipe clamp (2).

20

Pos: 8.21 /Überschriften/Überschriften 2/A-E/BBeleuchtung @ 0\mod_1195658399935_78.docx @ 1881 @ 2 @ 1

4.6 Lighting

Pos: 8.22 /BA/Ersti nbetriebnahme/EasyC ut/Anbau Bel euchtungsanlag e EC 28/32 (P) @ 10 \mod_1221661519150_78.docx @ 136233 @ @ 1

Commissioning

Pos: 9 /Layout Modul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-0-016

Fig. 9

• Install the light holder (1).

• From above, push warning boards (2) with lighting (3) into the light holder * (1).

• Secure with a spring cotter pin (4).

• Check functionality of the lighting.

* = Standardised section according to Din 11027

21

Start-up

Pos: 10.1 /Überschriften/Überschriften 1/F-J/Inbetri ebnahme @ 0\mod_1196327075811_78.docx @ 6375 @ 1 @ 1

5

Pos: 10.2 /Überschriften/Überschriften 2/U-Z/VVor bereitung en am Traktor @ 2\mod_1202363643678_78.docx @ 58694 @ 2 @ 1

Start-up

5.1 Preparations on tractor

Pos: 10.3 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - U nbeabsichtigtes Abkuppel n Fr ontmähwer ke @ 3\mod_1204641660735_78.docx @ 71218 @ @ 1

Danger! - Inadvertent uncoupling of the machine during road travel or work.

Effect: Danger to life, serious injuries or serious damage to the machine.

• Use extreme caution when attaching implements to or detaching them from the tractor! The accident prevention regulations must be complied with absolutely.

• When attaching or detaching the machine, do not walk between the tractor and the machine!

• The lower suspension arms of the front hydraulics on the tractor must be adjusted to swing freely. (see operating instructions for the front hydraulics)

• If the lower suspension arms on the tractor cannot be adjusted to swing freely, freeswinging lower suspension arm adapters must be installed.

• Lower suspension arm adapter order no. 140 190 (1x)

Pos: 10.4 /BA/Ersti nbetriebnahme/EasyC ut/EasyC ut 32 C V Fl oat/Vorberei tungen am Tr aktor @ 89\mod_1321957297103_78.docx @ 756679 @ @ 1

• Change the front lifting gear over to single-action

• Disconnect the lower suspension arm from the swing position

• Move the front axle suspension to the central position and deactivate it

Pos: 10.5 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

22

Pos: 10.6 /Überschriften/Übersc hriften 2/A-E/AAnbau an den Traktor @ 0\mod_1199717845194_78.docx @ 34039 @ 2 @ 1

5.2 Mounting onto the Tractor

Pos: 10.7 /BA/Inbetriebnahme/EasyC ut/Vorbereitung am Tr aktor Bild EC 28/32 @ 10 \mod_1221731786130_78.docx @ 136570 @ @ 1

3

1

2

6

1

5

Start-up

4 7

AFA-0-003

Fig. 10

Pos: 10.8 /BA/Inbetriebnahme/EasyC ut/WARNUNG - ungeeigneten Federstecker für das Kuppel drei eck ( Weiste-Dreieck) ver wendet @ 136\mod_1352385119522_78.docx @ 1208527 @ @ 1

WARNING!

When using a spring clip which is not suitable, the triangle linkage (Weiste triangle) can uncouple unintentionally. This can cause serious accidents.

Only use suitable spring clips for securing the triangle linkage.

Pos: 10.9 /BA/Inbetriebnahme/EasyC ut/Vorbereitung am Tr aktor EC 28/32CV 28/32 @ 10\mod_1221728655208_78.docx @ 136257 @ @ 1

• Carefully position the tractor with Weiste triangle (2) in front of the holder (1) of the frontmounted disc mower.

• The tension spring (3) must not be inside the holder

• Connect the Weiste triangle (2) to the holder (1)

• Set the distance between the ratchet mechanism (4) and latch (5) by adjusting the ratchet mechanism (4) to 1 mm (using the adjusting screw (7))

• Secure Weiste triangle (2) with spring cotter pin (6).

Pos: 10.10 /BA/Inbetri ebnahme/EasyCut/Achtung Abstand der M aschine zum Tr aktor zu geri ng @ 89\mod_1321957875595_78.docx @ 756771 @ @ 1

Pos: 10.11 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Caution! - The distance between the machine and the tractor is too small

Effect: damage to the tractor or the machine

Check free space for the front wheels at all steering angles. If the guards or swath flaps come into contact with the front wheels of the tractor, lower suspension arm adapters must be installed between the lower suspension arm and the Weiste triangle.

23

Start-up

Pos: 10.12.1 /Ü berschriften/Ü berschriften 3/U-Z/U nterlenkeradapter @ 79\mod_1314688743340_78.docx @ 697532 @ 3 @ 1

5.2.1 Lower suspension arm

Pos: 10.12.2 /BA/Inbetri ebnahme/EasyCut/U nt erlenker adapter /Unterlenkeradapter fi xieren Bild @ 79\mod_1314690338900_78.docx @ 697669 @ @ 1

A

B

2

3

1

EC-387-0

Fig. 11

Pos: 10.12.3 /BA/Inbetri ebnahme/EasyCut/U nterlenker adapter /Unterlenkeradapter fi xieren / pendel nd Ei nführtext @ 136\mod_1352380302114_78.docx @ 1208499 @ @ 1 The lower suspension arm adapters (1) serve as extension to increase the distance of the machine to the front wheels of the tractor.

On tractors with floating (height movable) lower links, the lower suspension arm adapters must be fastened.

On tractors with rigid lower links, the lower suspension arm adapters must be set floating.

Pos: 10.12.4 /BA/Inbetri ebnahme/EasyCut/U nterlenker adapter /Unterlenkeradapter fi xieren @ 136\mod_1352380102898_78.docx @ 1208413 @ @ 1

Fastening the Lower Suspension Arm Adapters

To do this:

• Connect the machine to the Weiste triangle.

• Lower the machine into working position.

• Move the front power lift into float position.

• Turn off the engine, remove the ignition key and secure the tractor and the machine against accidental start-up and against rolling.

• Turn out screw (2) until the bolt (A) of the lower suspension arm adapter (1) touches the stop (B) of the Weiste triangle (right and left machine side).

• Lock the screw (2) with nut (3).

Pos: 10.12.5 /BA/Inbetri ebnahme/EasyCut/U nterlenker adapter /Unterlenkeradapter pendel nd ei nstellen @ 136\mod_1352380217006_78.docx @ 1208442 @ @ 1

Setting the Lower Suspension Arm Adapters Floating

To do this:

• Connect the machine to the Weiste triangle.

• Lower the machine into working position.

• Move the front power lift into float position.

• Turn off the engine, remove the ignition key and secure the tractor and the machine against accidental start-up and against rolling.

• Screw in screw (2) completely.

• Lock the screw (2) with nut (3).

Pos: 10.13 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

24

Pos: 10.14 /Ü berschriften/Ü berschriften 2/U-Z/UÜ berpr üfung des Erstanbaues @ 35\mod_1257843599703_78.docx @ 330187 @ 2 @ 1

Start-up

5.3 Checking the First fitting

Pos: 10.15 /BA/Inbetri ebnahme/EasyCut/Ü ber prüfung des Erstanbaues Achtung EC F 280(M) / F 320(M) / F 360(M) @ 204\mod_1386142598536_78.docx @ 1701547 @ @ 1

CAUTION!

Machine or tractor may be damaged if the machine is connected incorrectly.

If the universal shaft is bent unfavourably, the machine runs irregularly and machine or tractor may be damaged seriously.

• To prevent damages, the machine must be aligned in parallel to the ground in the raised condition.

Pos: 10.16 /BA/Inbetri ebnahme/EasyCut/Ü ber prüfung des Erstanbaues Bild EC F 280(M) / F 320(M) / F 360(M) @ 205\mod_1386257293841_78.docx @ 1707146 @ @ 1

EC-460-0

Fig. 12

Pos: 10.17 /BA/Inbetri ebnahme/EasyCut/Ü ber prüfung des Erstanbaues Beschrei bung EC F 280(M) / F 320(M) / F 360(M) @ 205\mod_1386319363029_78.docx @ 1707967 @ @ 1 Mount top link on the A-frame (Weiste triangle) or on the upper coupling point of the machine so that the machine is aligned as parallel as possible to the ground in the raised condition.

To do this:

• Raise the machine.

• Switch off tractor, secure the tractor from rolling away and remove the ignition key.

• Check the parallelism of the machine to the ground.

If the parallelism is OK, connecting can be continued.

Pos: 10.18 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

If the parallelism deviates too strong:

• Lower machine to the ground.

• Switch off tractor, secure the tractor from rolling away and remove the ignition key.

• Move top link in the hole pattern on the A-frame (Weiste triangle).

• Raise the machine and check parallelism.

Repeat this process until the machine raises in parallel to the ground.

25

Start-up

Pos: 10.19 /Ü berschriften/Ü berschriften 2/F-J/GGel enkwelle @ 0\mod_1199781879794_78.docx @ 34542 @ 2 @ 1

5.4

Pos: 10.20 /BA/Sicherheit/Gel enkwell e/Gefahr - Sich drehende Gel enkwelle_2 @ 0\mod_1199781692950_78.docx @ 34523 @ @ 1

PTO shaft

Pos: 10.21 /BA/Sicherheit/Gel enkwell e/Gefahr - Antri ebsdr ehzahl 1000 beachten @ 3\mod_1204700292070_78.docx @ 71424 @ @ 1

Danger! - Rotating PTO shaft

Effect: Danger to life or serious injuries

• Install or detach the PTO shaft only with the engine switched off and the ignition key removed.

• Secure the tractor against rolling.

• Make sure that the PTO shaft is coupled properly (the lock of the PTO shaft must have snapped in).

• Make sure that the protective devices are attached properly.

• Never use a PTO shaft, the protective devices of which have not been attached.

• Replace damaged protective devices immediately

• Attach the safety chain of the PTO shaft so that the guard tube does not rotate simultaneously with the PTO shaft.

Pos: 10.22 /Ü berschriften/Ü berschriften 3/K-O/LLängenanpassung @ 1\mod_1201687632810_78.docx @ 53589 @ 3 @ 1

Danger! - Observe drive speed

Effect: Danger to life or serious injuries

• This machine is driven at a maximum PTO speed of 1000 rpm.

5.4.1 Length adjustment

Pos: 10.23 /BA/Erstinbetriebnahme/Gelenkwelle/M ähwer ke/Längenanpassung Gelenkwelle EC 32CVF @ 3\mod_1204701667336_78.docx @ 71443 @ @ 1

1

Pos: 10.24 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

2

AFA-0-006

Fig. 13

• Hold the two PTO shaft halves (1) and (2) next to each other

• Check the cover of the special section tubes and guard tubes

• Shorten special section tubes and guard tubes until they can move freely in any operating position

• For detailed information on adjusting the length, please refer to the operating instructions of the PTO shaft manufacturer

26

Pos: 10.25 /Ü berschriften/Ü berschriften 2/F-J/GGel enkwelle monti eren @ 2\mod_1202398342788_78.docx @ 59253 @ 2 @ 1

5.5 Install the PTO shaft

Pos: 10.26 /BA/Inbetri ebnahme/EasyCut/Anbau Gel enkwell e/Anbau Gelenkwelle @ 3\mod_1204702102883_78.docx @ 71462 @ @ 1

2

1

Pos: 10.27 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

AFA-0-005

Fig. 14

• Swivel the PTO shaft bracket under the Weiste triangle

• Push the PTO shaft (1) onto the front PTO shaft of the tractor and secure

• Secure the PTO shaft guard against turning with the retaining chain (2).

Start-up

27

Start-up

Pos: 10.28 /Ü berschriften/Ü berschriften 2/A-E/AAnbau und Ei nstellung der Entlastungsfedern ÜS @ 89\mod_1321958243040_78.docx @ 756797 @ 2 @ 1

5.6 Mounting and Adjusting the Relief Springs

Pos: 10.29 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Ei nstellung an den Entl astungsfeder n @ 0\mod_1196751594562_78.docx @ 12575 @ @ 1

Danger! - Setting on the compensation springs

Effect: Danger to life or serious injuries

• The compensation springs must only be removed in transport position. In the working position the compensation springs are subject to high tensile stress.

• Severe injury can be caused if the compensation springs are removed while in the working position.

• The lower threaded blocks on the compensation springs must be fully screwed in.

Pos: 10.30 /BA/Ei nstellungen/M ähwer ke/EasyCut/Entl astungsfeder(n)/Entl astungsfedern am Tr aktor einstell en Bild EC F 280/320/360 @ 136\mod_1352878872691_78.docx @ 1211577 @ @ 1

4 a

3

2 1

1 a

4

2

3

5

AFA-1-007

5

Fig. 15

Pos: 10.31 /BA/Ei nstellungen/M ähwer ke/EasyCut/Entl astungsfeder(n)/Entl astungsfedern am Tr aktor einstell en Text EC 28/32 28/32 C V @ 10\mod_1221737190442_78.docx @ 136798 @ @ 1

• Bring the front mowing unit into the transport position

• Hook compensation spring (3) onto perforated bar (4).

• Attach with holder (2) on support point

"a"

and secure with hinged cotter pin (1)

Pos: 10.32 /BA/Ei nstellungen/M ähwer ke/EasyCut/Entl astungsfeder(n)/Ei nstellen der Entl astungsfeder n am Tr aktor Maß 300-400 Hinweis @ 10\mod_1221737438036_78.docx @ 136841 @ @ 1

EC-443-0

Pos: 10.33 /BA/Inbetri ebnahme/EasyCut/Probel auf nach Erstmontag e @ 3\mod_1205215927275_78.docx @ 73555 @ 2 @ 1

Note

Setting dimension of the compensation springs

Effect: Proper use of the machine.

The distance between support point "a" of the compensation spring (3) and the pivot point of the tractor's lower suspension arms (5) should be between 300 – 400 mm.

5.7 Trial run after first installation

Pos: 10.34 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Caution!

After the first connection to the tractor, the machine must undergo a trial run.

• The machine must be in working position

• Do not switch on the PTO until the machine is resting on the ground and you are absolutely sure that there are no persons, animals or objects in the danger zone.

• Start a trial run of the machine from the driver’s seat of the tractor only.

• Lower the machine into working position.

• Carefully switch in the PTO of the tractor.

• Slowly increase the PTO speed to 1000 rpm.

• Check that the machine is running smoothly and without vibrations.

• Reduce the PTO speed to idling and wait for the cutting discs / mower drums to come to a stansdstill.

• Raise or lower the machine via the tractor hydraulics.

28

Pos: 10.35 /Ü berschriften/Ü berschriften 2/A-E/BBel euchtung anschließ en @ 33\mod_1254385308979_78.docx @ 319105 @ 2 @ 1

5.8 Lighting connection

Pos: 10.36 /Abkürzungen /Abkürzung en Beschrei bung/Opti onal @ 102\mod_1331109267412_78.docx @ 902782 @ @ 1 optional

Pos: 10.37 /BA/Inbetri ebnahme/EasyCut/Bel euchtung/Anschluss Bel euchtung Bild EC F 280/ 320/360 / F 280/320/360 M @ 234\mod_1394015986938_78.docx @ 1861754 @ @ 1

2 1 3

Start-up

3

EC-470-0

Fig. 16

Pos: 10.38 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.docx @ 1092566 @ @ 1

Pos: 10.39 /BA/Inbetri ebnahme/Schwader /Hinweis Sauber keit der Stecker und Steckdosen @ 2\mod_1202399563131_78.docx @ 59273 @ @ 1

Note

Before inserting the plugs, make certain the plugs and sockets are clean and dry. Dirt and moisture may result in short circuits!

Pos: 10.40 /BA/Inbetri ebnahme/Schwader /Anschluss Beleuchtung/Anschluss Beleuchtung Text @ 36\mod_1260783798936_78.docx @ 336718 @ @ 1

The lighting system is connected via the 7-pin connection cable (1).

To do this:

• Insert the 7-pin plug of the connection cable (1) into the relevant socket (2) of the tractor.

• Insert the 7-pin connection cable plug (1) into the appropriate socket (3) of the machine.

• Position the cable so that it will not come in contact with the wheels.

Pos: 10.41 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

29

Start-up

Pos: 10.42 /Ü berschriften/Ü berschriften 2/F-J/HH ydr auli k @ 0\mod_1199776034950_78.docx @ 34205 @ 2 @ 1

5.9 Hydraulics

Pos: 10.43 /Abkürzungen /Abkürzung en Beschrei bung/Opti onal @ 102\mod_1331109267412_78.docx @ 902782 @ @ 1

Pos: 10.44 /Ü berschriften/Ü berschriften 3/P-T/SSpezi elle Sicher heitshi nweise @ 0\mod_1197301069931_78.docx @ 17662 @ 3 @ 1 optional

5.9.1 Special Safety Instructions

Pos: 10.45 /BA/Sicherheit/H ydr auli k/Warnung - Anschluss der H ydrauli klei tungen @ 0\mod_1199776548685_78.docx @ 34225 @ @ 1

Warning ! - Connection of the hydraulic line

Effect: severe injuries due to penetration of hydraulic oil under the skin.

• When connecting the hydraulic hoses to the hydraulic system of the tractor, the system must be relieved of the pressure on either side.

• Due to the risk of injury when searching for leaks, always use suitable tools and wear protective goggles.

• Seek medical help immediately should injuries occur! Danger of infection.

• Depressurise prior to uncoupling the hydraulic hoses and working on the hydraulic system!

• Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The replacement hoses must fulfil the technical requirements set by the equipment manufacturer.

Pos: 10.46 /Ü berschriften/Ü berschriften 3/F-J/HH ydr auli kl eitungen anschließ en @ 0\mod_1199777037794_78.docx @ 34244 @ 3 @ 1

5.9.2 Connecting the hydraulic lines

Pos: 10.47 /BA/Sicherheit/H ydr auli k/WARNUNG - Vertauschen der H ydrauli kkl eitungen, wenn EW @ 9\mod_1220871857985_78.docx @ 128182 @ @ 1

Pos: 10.48 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Warning - If the hydraulic hoses are interchanged when connecting them to the hydraulic system of the tractor, the functions will be interchanged as well.

Effect: Injuries, serious damage to the machine

• Identify the hydraulic connections.

• Always ensure correct connection between the machine and the tractor.

• When engaging the hydraulic hose, the hydraulic control unit must be in float position or in

"lowering" position.

30

Pos: 10.49 /BA/Sicherheit/H ydr auli k/Achtung - Verschmutzung der H ydrauli kanlag e @ 2\mod_1202393336803_78.docx @ 59155 @ @ 1

Caution! - Soiling of the hydraulic system

Effect: Damages to the machine

• When connecting the quick couplings, ensure that these are clean and dry.

• Note chafing areas or points of contact.

Pos: 10.50 /BA/Inbetri ebnahme/H ydrauli kkupplungen anschließ en all e Maschi nen/Hi nweis H ydrauli kanschluss BA Traktor @ 220\mod_1391434710718_78.docx @ 1782774 @ @ 1

Start-up

Note

For further information about connecting the hydraulic lines, refer to the tractor operating instructions.

Pos: 10.51 /BA/Inbetri ebnahme/H ydrauli kkupplungen anschließ en all e Maschi nen/Hi nweis H ydrauli kaufkl eber an der M aschine beachten @ 204\mod_1386153225929_78.docx @ 1701911 @ @ 1

Note

Connect hydraulic hoses correctly.

• The hydraulic hoses are marked with numbers and coloured dust caps.

Pos: 10.52 /BA/Inbetri ebnahme/EasyCut/H ydrauli k/H ydrauli kanschluss Bild EC F 280/320/360/ (M) @ 234\mod_1394086580639_78.docx @ 1864567 @ @ 1

EC-471-0

Fig. 17

Pos: 10.53 /BA/Inbetri ebnahme/H ydrauli kkupplungen anschließ en all e Maschi nen/H ydr auli kkuppl ung en anschließ en T eil1 @ 213\mod_1390207328923_78.docx @ 1749237 @ @ 1

• Set the single-action control units of the tractor to float position.

• Turn off the tractor and secure it against the possibility of rolling back.

Pos: 10.54.1 /BA/Bedienung /EasyC ut/Schutze/Bei Ausführung hydr aulischer Seitenschutz @ 332\mod_1428387861893_78.docx @ 2536837 @ @ 1

With hydraulic side guards design

Pos: 10.54.2 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung Quetschgefahr/Senken von Seitenschutz @ 331\mod_1427802696458_78.docx @ 2532405 @ @ 1

WARNING!

Crushing hazard when lowering the side guards

While lowering the hydraulic side guards, there is a danger of being crushed between side guard and upper protective cover.

• While lowering the side guards, make sure that there is no one in the danger zone .

Pos: 10.54.3 /BA/Bedienung /EasyC ut/Schutze/Absenken hydr aulischer Seitenschutz_T ext @ 332 \mod_1428387391162_78.docx @ 2536775 @ @ 1

• Fold down the side guards by means of double-action control unit (red1/blue1) of the tractor.

Pos: 11 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

31

Driving and Transport

Pos: 12.1 /Überschriften/Überschriften 1/F-J/F ahr en und Transport @ 0\mod_1196330049217_78.docx @ 6553 @ 1 @ 1

6 Driving and Transport

Pos: 12.2 /BA/Sicher heit/Fahren und Transport/Mitfahr en Straß enfahrt/Gefahr Straß enfahrt, Mitfahren EasyCut Front @ 3\mod_1204784303933_78.docx @ 72994 @ @ 1

Danger! - Transport / road travel

Effect: Danger to life, serious injuries or serious damage to the machine.

• Before swivelling the machine up into transport position, switch off the PTO.

• Wait until machine stops

• When travelling on public roads, observe the applicable current regulations (lighting, identification, axle loads, permitted front end dimension, etc.)!

• When being transported on public roads, the mowing unit must be lifted.

• It is forbidden to carry passengers on the machine.

• Before starting, ensure that you have perfect visibility on and around the tractor and the machine.

Pos: 12.3 /BA/Sicher heit/Fahren und Transport/Absperrhahn/Transport / Str aßenfahr t Absperr hahn in Fronthydraulik Traktorseitig schließ en @ 33\mod_1254118215456_78.docx @ 318342 @ @ 1

DANGER! - Transport / road travel

Effect: Danger to life, serious injuries or serious damage to the machine.

• A shut-off valve must be existent in the hydraulic line for the front hydraulic of the tractor.

• The shut-off valve must always be locked during transport / road travel.

Pos: 12.4 /Überschriften/Überschriften 2/A-E/BBeleuchtung @ 0\mod_1195658399935_78.docx @ 1881 @ 2 @ 1

6.1 Lighting

Pos: 12.5 /BA/Sicher heit/Fahren und Transport/Beleuchtung/Bel euchtungsanlag e alle M aschinen @ 7 \mod_1215519058839_78.docx @ 103206 @ @ 1

Pos: 12.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - Lighting system

Effect: Danger to life, serious injuries or serious damage to the machine.

• Before transporting on public roads, always connect the lighting system and perform a function check.

• Keep the lighting system clean. Soiled lights and spotlights impair road safety.

• Replace defective light bulbs or broken spotlights.

• When transporting on public highways, the machine must be in the transport position.

32

Pos: 12.7 /BA/F ahren und Tr ansport/EasyCut/Vor baumaß Länderabhängig EC _Front @ 3\mod_1204784822668_78.docx @ 73052 @ @ 1

A 3,5 m

Driving and Transport

EC-224-0

Fig. 18

Note - Depending on the country

If the front end dimension "A" exceeds 3.5 m, provide suitable means (e.g. assistant giving instructions or mirror at road junctions) to ensure road safety (data sheet for attached implements supplied by the Federal Minister for Transport).

Pos: 12.8 /BA/F ahren und Tr ansport/EasyCut/Schutze i n Tr ansportstellung bringen EC28/32 @ 10\mod_1221735727426_78.docx @ 136637 @ @ 1

EC-0-014

Pos: 12.9 /BA/F ahren und Tr ansport/EasyCut/F eststell er und Schnäpper @ 78\mod_1314002912379_78.docx @ 694482 @ 2 @ 1

Fig. 19

Always move the guard (1) from the right and left-hand sides to the transport position before road travel.

6.2 Clamp and Buffer

1

Pos: 13 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-385-0

Fig. 20

Check the clamp and buffer (1) for tight fit every time before transport or road travel.

If the clamp and buffer show signs of damage or wear, replace them.

Item No.: 00 250 831 1

33

Operation

Pos: 14.1 /Überschriften/Überschriften 1/A-E/Bedienung @ 0\mod_1199789505403_78.docx @ 34825 @ 1 @ 1

7

Pos: 14.2 /Überschriften/Überschriften 2/U-Z/VVor dem M äheinsatz @ 3\mod_1204788384465_78.docx @ 73168 @ 2 @ 1

Operation

7.1 Before mowing

Pos: 14.3 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Arbeitseinsatz / M ähen @ 73\mod_1307695972255_78.docx @ 654926 @ @ 1

DANGER! - Using the machine for work

Effect: Danger to life, injuries or damage to the machine.

• The glide skids must rest on the ground before start-up and during work

• Maintain an adequate safety distance from the cutting tools during operation

• There is danger of foreign objects being forcibly ejected even when the machine is operated properly. Persons must therefore be directed out of the danger zone of the machine.

• Special care should be taken when working near roads and buildings)

Pos: 14.4 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer keGefahr - U ner wartete Beweg ung der Schnei dwer kzeuge bzw. des Mähwer kes ( 2014-10-10 12:32:30) @ 3\mod_1204788756340_78.docx @ 73207 @ @ 1

Danger! - Unexpected movement of the cutting tools or the mowing unit. Stones are hurled up during operation

Effect: Danger to life, injuries or damage to the machine.

• Do not carry out work on the disc mower until the PTO has been switched off, the engine has been turned off and the ignition key has been removed! Secure the tractor against accidental start-up and against rolling!

• Support the lifted cutter bar! Never step under suspended loads!

• Before using the machine, always check the protective devices for damage. Replace damaged protective devices immediately.

• Safe operation is only guaranteed if the blades have been fitted according to the instructions!

• Before starting operation, always check the mowing unit for damaged, missing or worn blades, retaining bolts, leaf springs and cutting discs/blade drum; replace any parts that are damaged, missing or worn!

• Always replace missing and damaged blades in sets to prevent unbalanced rotation!

• Never install unevenly worn blades on a drum/disc!

• Whenever a blade is changed, also inspect the fasteners and, if required, replace them!

• Move the protective devices into their protective positions.

Pos: 14.5 /BA/Bedi enung /EasyC ut/Mähen/Hi nweis Bei m M ähen Frontmähwer ke @ 33\mod_1254117934018_78.docx @ 318312 @ @ 1

Note while mowing

Effect: Proper use of the machine

• Change the front power lift to single-acting (only lifting, no pressing). The lowering of the mowing unit results from the dead weight of the mowing unit. The mowing unit must not be additionally loaded over the front power lift.

• During work the hydraulic control lever for the front power lift must be set to “

Float position

“.

Pos: 14.6 /BA/Bedi enung /EasyC ut/Mähen/Absperrhahn für di e Fronthydrauli k des Traktors lösen. @ 33\mod_1254119058096_78.docx @ 318361 @ @ 1

• Open the shut-off valve for the front hydraulic of the tractor.

Pos: 14.7 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

34

Pos: 14.8 /Überschriften/Überschriften 2/P-T/SSchutze i n Arbeitsstellung bringen @ 35\mod_1257499551281_78.docx @ 329310 @ 2 @ 1

7.2 Moving the guards into the working position

Pos: 14.9 /BA/Bedi enung /EasyC ut/Schutze/Schutze i n Arbeitsstell ung bringen EC 28/32 @ 10\mod_1221736185786_78.docx @ 136703 @ @ 1

Operation

Pos: 14.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-0-013

Fig. 21:

Move the guard covers (1) from the right and left-hand sides to the working position each time before using the machine.

35

Operation

Pos: 14.11 /Ü berschriften/Ü berschriften 2/A-E/AAbbau der Maschi ne @ 3\mod_1204792387824_78.docx @ 73245 @ 2 @ 1

7.3 Detaching the machine

Pos: 14.12 /BA/Sicherheit/EasyCut/Gefahr - M aschine abstell en_ohne H ydrauli kschlauch @ 3\mod_1204793072152_78.docx @ 73283 @ @ 1

Danger! - Unexpected movements of the machine

Pos: 14.13 /Ü berschriften/Ü berschriften 2/A-E/DD emontage der Entlastungsfeder (n) @ 3\mod_1204792429324_78.docx @ 73264 @ 2 @ 1

Effect: Danger to life, serious injuries

• No one is permitted inside the danger zone.

• Park the machine on a solid and even surface.

• You should not unhitch the machine until the engine has been switched off and the ignition key has been removed.

• Secure the tractor against rolling.

• Use extreme caution when attaching implements to or detaching them from the tractor! The accident prevention regulations must be complied with absolutely.

• When detaching the machine, do not walk between the tractor and the machine!

7.4 Removing the compensation spring(s)

Pos: 14.14 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Ei nstellung an den Entl astungsfeder n @ 0\mod_1196751594562_78.docx @ 12575 @ @ 1

Pos: 14.15 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - Setting on the compensation springs

Effect: Danger to life or serious injuries

• The compensation springs must only be removed in transport position. In the working position the compensation springs are subject to high tensile stress.

• Severe injury can be caused if the compensation springs are removed while in the working position.

• The lower threaded blocks on the compensation springs must be fully screwed in.

36

Pos: 14.16 /BA/Bedienung /EasyC ut/Weiste-Dreieck/Abbau Weiste-Drei eck Bild EC 28/32 @ 10\mod_1221736766364_78.docx @ 136752 @ @ 1

Operation

1

2

3

4

EC-0-020

AFA-0-010

Fig. 22

Pos: 14.17 /BA/Bedienung /EasyC ut/Weiste-Dreieck/Abbau Weiste-Drei eck T ext EC 28/32 28/32CV @ 10\mod_1221736705176_78.docx @ 136733 @ @ 1

• Bring the front mowing unit into the transport position.

• Remove compensation spring (2) and hang it on hook (1).

• Lower front-mounted disc mower.

• Pull spring cotter pin (5) out of the Weiste triangle.

• Release the interlock of the holding triangle.

• Loosen the guard cloth.

• Remove the retaining chain (4) of the PTO shaft (3).

• Remove the PTO shaft (3) from the tractor side and place on the PTO shaft bracket

• Carefully lower the front hydraulics.

• Drive carefully out of the holder of the front-mounted disc mower.

Pos: 15 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

37

Settings

Pos: 16.1 /Überschriften/Überschriften 1/A-E/Ei nstellungen @ 0\mod_1199868783862_78.docx @ 36141 @ 1 @ 1

8 Settings

Pos: 16.2 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - R epar atur _Wartung_R einigungs_3 @ 0\mod_1196660613260_78.docx @ 9153 @ @ 1

Pos: 16.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - When performing repair, maintenance or cleaning work on the machine , or in the case of technical intervention, drive elements may start moving.

Effect: Danger to life, injuries or damage to the machine.

• Switch off the engine and remove the ignition key.

• Secure the machine against accidental start-up and against rolling!

• The cutter blades can continue to rotate after the drive has been switched off. Only approach the machine once the work tools have come to a complete standstill!

• After completing maintenance work reattach all safety devices properly.

• Avoid skin contact with oil and grease.

• Seek medical help immediately should injuries caused by oil escaping under pressure occur.

38

Pos: 16.4 /Überschriften/Überschriften 2/A-E/EEntlastungsfeder(n) @ 2\mod_1203508983876_78.docx @ 66384 @ 2 @ 1

Settings

8.1 Compensation Spring(s)

Pos: 16.5 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Einstell ung an den Entlastungsfedern @ 0\mod_1196751594562_78.docx @ 12575 @ @ 1

Danger! - Setting on the compensation springs

Effect: Danger to life or serious injuries

• The compensation springs must only be removed in transport position. In the working position the compensation springs are subject to high tensile stress.

• Severe injury can be caused if the compensation springs are removed while in the working position.

• The lower threaded blocks on the compensation springs must be fully screwed in.

Pos: 16.6 /BA/Einstell ung en/Mähwer ke/EasyC ut/Entlastungsfeder(n)/Entlastungsfedern am Traktor einstellen Bil d EC 28/32 @ 10 \mod_1221737502192_78.docx @ 136861 @ @ 1

1 a

4

2

3

5

AFA-1-007

Fig. 23

Pos: 16.7 /BA/Einstell ung en/Mähwer ke/EasyC ut/Entlastungsfeder(n)/Entlastungsfedern am Traktor einstellen T ext EC 28/32 28/32 CV @ 10\mod_1221737190442_78.docx @ 136798 @ @ 1

• Bring the front mowing unit into the transport position

• Hook compensation spring (3) onto perforated bar (4).

• Attach with holder (2) on support point

"a"

and secure with hinged cotter pin (1)

Pos: 16.8 /BA/Einstell ung en/Mähwer ke/EasyC ut/Entlastungsfeder(n)/Einstell en der Entlastungsfedern am Traktor M aß 300-400 Hi nweis @ 10\mod_1221737438036_78.docx @ 136841 @ @ 1

Pos: 16.9 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

Setting dimension of the compensation springs

Effect: Proper use of the machine.

The distance between support point "a" of the compensation spring (3) and the pivot point of the tractor's lower suspension arms (5) should be between 300 – 400 mm.

39

Settings

Pos: 16.10 /Ü berschriften/Ü berschriften 2/A-E/EEinstellung der Entlastungsfeder n (2015- 10- 19 15:05:29) @ 0\mod_1196666659447_78.docx @ 10133 @ 2 @ 1

8.2 Adjusting the Compensation Springs

Pos: 16.11 /BA/Ei nstellungen/M ähwer ke/EasyCut/Bodendruck/Bodendr uck allgemeiner T ext alle EC @ 0\mod_1196667271181_78.docx @ 10190 @ @ 1

The ground pressure for the cutter bar is adjusted to local conditions by means of the compensation springs. In order to protect the sward the load on the mowing spar must be relieved so that it does not jump when mowing, yet does not leave any skid marks on the ground.

Pos: 16.12 /BA/Ei nstellungen/M ähwer ke/EasyCut/Bodendruck/Bodendr uck ei nstellen Bild EC 28/32 @ 10 \mod_1221738032880_78.docx @ 136927 @ @ 1

2

1

EC-145-1

Fig. 24

Pos: 16.13 /BA/Ei nstellungen/M ähwer ke/EasyCut/Bodendruck/Bodendr uck ei nstellen T ext EC 28/32 28/32C V @ 10 \mod_1221737841223_78.docx @ 136908 @ @ 1

Pos: 16.14 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

Retaining chain shorter= reduced ground pressure

Retaining chain longer= increased ground pressure

If a telescope upper suspension arm is being used (optional)

The higher the compensation springs (1) are hooked into the perforated bar (2), the lower the pressure on the ground in the front part of the cutter bar.

If the compensation springs are hooked in too high, the mowing unit will tip towards the rear. or:

The lower the compensation springs (1) are hooked into the perforated bar (2), the greater the pressure on the ground in the front part of the cutter bar.

If the compensation springs are hooked in too low, the mowing unit will have too much weight on the ground in front.

40

Pos: 16.15 /Ü berschriften/Ü berschriften 2/A-E/EEinstellen der Schnitthöhe @ 0\mod_1196660879619_78.docx @ 9191 @ 2 @ 1

8.3 Adjusting the cutting height

Pos: 16.16 /BA/Ei nstellungen/M ähwer ke/Schnitthöhe/Schni tthöhe Bil d EC 28/32 @ 10\mod_1221738803864_78.docx @ 136972 @ @ 1

1

Settings

AFA-0-012

Fig. 25

Pos: 16.17 /BA/Ei nstellungen/M ähwer ke/Schnitthöhe/Schni tthöhe größer _gering er @ 0\mod_1196661562478_78.docx @ 9269 @ @ 1

The cutting height is adjusted via the top link (1).

To do this:

• Lower the front mowing unit into working position

• Rotate the top suspension arm (1)

Top suspension arm longer = smaller cutting height

Top suspension arm shorter = bigger cutting height

Pos: 16.18 /BA/Ei nstellungen/M ähwer ke/T eleskopoberlenker @ 3\mod_1204708776180_78.docx @ 71835 @ 3 @ 1

8.3.1 Telescopic upper suspension arm

1

3

2

Pos: 16.19 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

AFA-0-020

Fig. 26:

In order to allow the front-mounted disc mower to adapt to the ground in the direction of travel, a telescopic upper suspension arm can be purchased as optional additional equipment. Via the telescopic upper suspension arm, the cutting height is set by loosening the counter nut (2) and

(3). By moving the lockclip (1), the compression spring of the telescopic upper suspension arm is released. This guarantees optimum adaptation of the front mowing unit in the direction of travel.

41

Settings

Pos: 16.20 /BA/Ei nstellungen/M ähwer ke/Einstell ung der Keilriemenspannung EC 28/32 @ 10\mod_1221739581380_78.docx @ 137022 @ 2 @ 1

8.4 Setting of the V-belt Tension

(except EC 28 M)

Pos: 17 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-0-008

Fig. 27:

The drive V-belts maintain their tension by means of a compression spring (2). To adjust dimension "a", unscrew the nut (1). Turn the nuts until dimension "a" = 205 mm is reached. Lock nuts again.

42

Pos: 18.1 /Überschriften/Überschriften 1/U-Z/Wartung @ 0\mod_1199883581050_78.docx @ 36685 @ 1 @ 1

Maintenance

9

Pos: 18.2 /Überschriften/Überschriften 2/P-T/SSpeziell e Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Maintenance

9.1 Special Safety Instructions

Pos: 18.3 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - U nvorhergesehene Akti onen an der M aschine_1 @ 0\mod_1196782315875_78.docx @ 14851 @ @ 1

Danger! - Unexpected actions on the machine

Effect: Danger to life, injuries or damage to the machine.

• Always make certain that the drive and the engine are switched off before doing any repairs, maintenance or cleaning.

• The cutting discs continue to run!

• Switch off the engine and remove the ignition key.

• Secure the machine against accidental start-up and against rolling!

Pos: 18.4 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Bei unregel mäßiger Kontr olle der Messer kli ngen und H altebolzen @ 0\mod_1196782406281_78.docx @ 14870 @ @ 1

Danger! - When checking the cutter blades and retaining bolts only sporadically

Effect: Danger to life, injuries or damage to the machine.

• Always check the mowing units for damaged, missing or worn blades, retaining bolts, leaf springs and cutting discs/blade drum before starting operation; replace any parts that are damaged, missing or worn!

• Always replace missing and damaged blades in sets to prevent unbalanced rotation!

• Never mount unevenly worn blades on a drum/disc!

• Whenever a blade is changed, also inspect the fasteners and replace them, if necessary!

Pos: 18.5 /Überschriften/Überschriften 3/P-T/PPr obel auf @ 0\mod_1196833698843_78.docx @ 15023 @ 3 @ 1

9.1.1 Test run

Pos: 18.6 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Probel auf Einzahl Mähwer k muss auf Boden auflieg en @ 11\mod_1223615241207_78.docx @ 148217 @ @ 1

Pos: 18.7 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - Testing the machine after repair, maintenance or cleaning work and after technical intervention.

Effect: Danger to life or serious injuries

• The mowing unit must be in working position

• Do not switch on the drives until the mowing unit is resting on the ground and you are absolutely sure that neither persons, animals nor objects are in the danger zone.

• Start a trial run of the machine only from the driver’s seat.

43

Maintenance

Pos: 18.8 /Überschriften/Überschriften 2/A-E/EErsatzteile @ 0\mod_1196782991234_78.docx @ 14927 @ 2 @ 1

9.2 Spare Parts

Pos: 18.9 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer keWARNUN G - Verwendung von nicht zugel assenen Ersatzteil en @ 308\mod_1417011577394_78.docx @ 2392925 @ @ 1

Pos: 18.10.1 /Ü berschriften/Ü berschriften 2/A-E/AAnzi ehdrehmomente @ 202\mod_1385711894606_78.docx @ 1693123 @ 2 @ 1

Warning! - Using non-approved spare parts.

Effect: Danger to life, serious injuries or loss of warranty claims as well as exclusion of liability

• Use only authentic KRONE spare parts and accessories authorised by the manufacturer.

The use of spare parts, accessories or additional equipment not manufactured, tested or approved by KRONE will exclude any liability for consequential damage.

9.3 Tightening torques

Pos: 18.10.2 /Ü berschriften/Ü berschriften 3/K-O/MM etrische Gewindeschrauben mit R egelgewi nde @ 322\mod_1424945442462_78.docx @ 2483466 @ 3 @ 1

9.3.1 Metric Thread Screws with Control Thread

Pos: 18.10.3 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewi ndeschr auben mi t R egelgewinde T abelle @ 321\mod_1424760222607_78.docx @ 2477725 @ @ 1

Pos: 18.10.4 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

M4

M5

M6

M8

M10

M12

M14

M16

M20

M22

M24

M27

M30

NOTICE

The table does not apply to countersunk screws with hexagonal socket in case the countersunk screw is tightened via hexagonal socket.

Tightening torque in Nm (unless otherwise stated)

A = thread size

(stability class can be seen on screw head)

A

Stability class

29

42

5.6 8.8 10.9 12.9

Tightening torque (Nm)

3.0

5.9

4.4

8.7

5.1

10

10

25

49

85

15

36

72

125

18

43

84

145

135

210

425

571

730

200

310

610

832

235

365

710

972

1050 1220

1100 1550 1800

1450 2100 2450

44

Pos: 18.10.5 /Ü berschriften/Ü berschriften 3/K-O/MM etrische Gewindeschrauben mit F eing ewinde @ 322\mod_1424945855944_78.docx @ 2484627 @ 3 @ 1

Maintenance

9.3.2 Metric Thread Screws with Fine Thread

Pos: 18.10.6 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewi ndeschr auben mi t F eingewi nde Tabell e @ 321\mod_1424845229172_78.docx @ 2480186 @ @ 1

Tightening torque in Nm (unless otherwise stated)

A

M12 x

1.5:

M14 x 1.5

M16 x 1.5

M18 x 1.5

M20 x 1.5

M24 x 2

M27 x 2

M30 x 1.5

Pos: 18.10.7 /Ü berschriften/Ü berschriften 3/K-O/MM etrische Gewindeschrauben mit Senkkopf und Innensechskant @ 323\mod_1424945970760_78.docx @ 2484818 @ 3 @ 1

5.6

Stability class

8.8 10.9 12.9

Tightening torque (Nm)

88 130 152

145

222

368

465

787

800

213

327

525

662

249

382

614

775

1121 1312

1148 1635 1914

2100 2650

A = thread size

(stability class can be seen on screw head)

9.3.3 Metric Thread Screws with Countersunk Head and Hexagonal Socket

Pos: 18.10.8 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmoment e Metrische Gewi ndeschr auben mi t Senkkopf und Innensechskant T abelle @ 321\mod_1424843938347_78.docx @ 2480155 @ @ 1

NOTICE

The table applies only to countersunk screws with hexagonal socket and metric thread which are tightened via hexagonal socket.

Tightening torque in Nm (unless otherwise stated)

A = thread size

(stability class can be seen on screw head)

A

M4

M5

M6

M8

M10

M12

M14

M16

M20

Stability class

23

34

5.6 8.8 10.9 12.9

Tightening torque (Nm)

2.5

4.7

3.5

7

4.1

8

8

20

39

68

12

29

58

100

15

35

67

116

108 160 188

168 248 292

340 488 568

A

BM 400 0234

45

Maintenance

Pos: 18.11 /Ü berschriften/Ü berschriften 3/A-E/AAbweichende Anziehdr ehmomente @ 369\mod_1441722353234_78.docx @ 2702740 @ 3 @ 1

9.3.4 Deviating Tightening Torques

Pos: 18.12 /BA/War tung/Drehmomente / AnziehdrehmomenteAbweichendes Drehmoment EasyC ut @ 391\mod_1445869003328_78.docx @ 2801980 @ @ 1

Screws / nuts MA [Nm]

Nut for shear protection (rotary hub)

Bearing housing for cutting disc

Pos: 18.13 /BA/War tung/Muttern und Schrauben ( 50h) anzi ehen @ 0\mod_1196949864530_78.docx @ 15293 @ @ 1

Bearing housing for blade drum

300

50

50

Pos: 18.14 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

Regularly check that nuts and bolts are tightly in place (approx. every 50 hours) and tighten them if necessary.

46

Pos: 18.15 /Ü berschriften/Ü berschriften 2/F-J/FFüll meng en und Schmier mittel bezeichnungen der Getriebe @ 0\mod_1196951094046_78.docx @ 15335 @ 2 @ 1

9.4 Filling Quantities and Lubrication Designations for Gearboxes

Pos: 18.16 /BA/War tung/Mähwer ke/Hi nweis Ein Öl wechsel am M ähhol m ist nicht erforderlich. @ 68\mod_1304577391388_78.docx @ 628708 @ @ 1

Note

No oil change is required on the cutter bar.

Pos: 18.17 /BA/War tung/Tabellen_F üll mengen/M ähwer ke/T echnische D aten Betriebsstoffe Füll meng en EC 28/32 @ 10\mod_1221740251911_78.docx @ 137063 @ @ 1

Filling

Quantity

Angular gearbox EasyCut 28 (P) / 32 (P)

Angular gearbox EasyCut 28 M

Mower drive gearbox EasyCut 28 M

Cutter bar EasyCut 28

Cutter bar EasyCut 32

Pos: 18.18 /BA/War tung/Zei tinter valle an den Getrieben 200 h @ 0\mod_1196951919921_78.docx @ 15373 @ 3 @ 1

[litres]

1.0 l

0.5 l

0.4 l

6.0 l

7.0 l

Filtered oils

Brand name

SAE90

9.4.1 Oil Level Check and Oil Change Intervals (Gearboxes)

Maintenance

Bio-degradable lubricants

Brand name

On request

Pos: 18.19 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note - Oil level check and oil change (gearboxes) and lubricating the machine

Effect: Long expected service life of machine

• First oil change on all gearboxes after 50 operating hours, then every 200 operating hours

(but at least once a year).

• Before using the machine always check the oil level.

• With bio-degradable oils the changing intervals must be complied with absolutely because of ageing of the oils.

47

Maintenance

Pos: 18.20.1 /Ü berschriften/Ü berschriften 2/U-Z/WWi nkelgetriebe @ 0\mod_1197005918299_78.docx @ 15435 @ 2 @ 1

9.5

Pos: 18.20.2 /Ü berschriften/Ü berschriften 3/F-J/FFrontmähwer k (CV+CR I) @ 0\mod_1197008615440_78.docx @ 15609 @ 3 @ 1

Angular gearbox

9.5.1 Front Mowing Unit (CV+CRI)

Pos: 18.20.3 /BA/Wartung/Öl kontroll e_Wechsel/M ähwer ke/Bild Wi nkelgetriebe EC 28/32 @ 10\mod_1221740931598_78.docx @ 137129 @ @ 1

1

AFA-0-016

Fig. 28

Pos: 18.20.4 /BA/Wartung/Öl kontroll e_Wechsel/Öl kontrolle_ALT/Öl kontrolle SAE 90 @ 0\mod_1197008973815_78.docx @ 15649 @ @ 1

Oil level check:

• For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)".

• Unscrew the inspection screw (1)

• Oil level up to bore hole (1)

• If necessary, top up the oil (SAE 90)

• Screw the check screw (1) back in.

Pos: 18.20.5 /BA/Wartung/Öl kontroll e_Wechsel/Öl wechsel_ALT/Ölwechsel Version absaugen @ 10\mod_1221740650161_78.docx @ 137085 @ @ 1

Oil change:

• For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)".

• Unscrew the inspection screw (1)

• Extract oil

• Top up oil (oil level up to hole (1))

• Screw the inspection screw (1) back in.

Pos: 18.20.6 /BA/Wartung/Öl kontroll e_Wechsel/Ölqualität /Öl menge: siehe Kapitel @ 0\mod_1197007859486_78.docx @ 15531 @ @ 1

Oil quality / oil quantity: see Chapter "Filling Quantities and Lubricant Designations for

Gearboxes"

Pos: 18.20.7 /BA/Wartung/Öl kontroll e_Wechsel/Hi nweis - Altöl or dnungsg emäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 18.21 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

48

Pos: 18.22.1 /Ü berschriften/Ü berschriften 2/K-O/MM äherantri ebsg etriebe @ 9\mod_1221045800746_78.docx @ 131475 @ 2 @ 1

9.6 Mower Drive Gearbox

Pos: 18.22.2 /Abkürzungen /Abkürzung en spr achneutral/EasyC ut/EasyCut 28 M @ 10\mod_1221658268900_0.docx @ 136051 @ @ 1

(EasyCut 28 M)

Pos: 18.22.3 /BA/Wartung/Öl kontroll e_Wechsel/M ähwer ke/Bild M äher antriebsgetri ebe EC 28/32 @ 10 \mod_1221741509333_78.docx @ 137196 @ @ 1

Maintenance

EC-227-0

Fig. 29

Pos: 18.22.4 /BA/Wartung/Öl kontroll e_Wechsel/Öl kontrolle_ALT/Öl kontrolle SAE 90 @ 0\mod_1197008973815_78.doc x @ 15649 @ @ 1

Oil level check:

• For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)".

• Unscrew the inspection screw (1)

• Oil level up to bore hole (1)

• If necessary, top up the oil (SAE 90)

• Screw the check screw (1) back in.

Pos: 18.22.5 /BA/Wartung/Öl kontroll e_Wechsel/Öl wechsel_ALT/Ölwechsel Version5 @ 9 \mod_1221047052043_78.docx @ 131562 @ @ 1

Oil change:

Pos: 18.22.6 /BA/Wartung/Öl kontroll e_Wechsel/Ölqualität /Öl menge: siehe Kapitel @ 0\mod_1197007859486_78.docx @ 15531 @ @ 1

• For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)".

• Screw out the oil drain plug (1)

• Collect the used oil in a suitable drip pan

• Screw in the oil drain plug (1)

• Top up the oil (2) (oil level up to hole (1))

Oil quality / oil quantity: see Chapter "Filling Quantities and Lubricant Designations for

Gearboxes"

Pos: 18.22.7 /BA/Wartung/Öl kontroll e_Wechsel/Hi nweis - Altöl or dnungsg emäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Pos: 18.23 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The used oil must be disposed of correctly

49

Maintenance

Pos: 18.24.1 /Ü berschriften/Ü berschriften 2/K-O/OÖlstandskontr olle und Öl wechsel am M ähhol m @ 0\mod_1197017549815_78.docx @ 15963 @ 2 @ 1

9.7

Pos: 18.24.2 /Ü berschriften/Ü berschriften 3/K-O/OÖl wechsel @ 0\mod_1197021941955_78.docx @ 16139 @ 3 @ 1

Oil level check and oil change on the cutter bar

9.7.1 Oil change

Pos: 18.24.3 /BA/Wartung/Mähwerke/Hi nweis Ei n Öl wechsel am M ähhol m ist nicht erfor derlich. @ 68 \mod_1304577391388_78.docx @ 628708 @ @ 1

Pos: 18.24.4 /Ü berschriften/Ü berschriften 3/K-O/OÖl kontroll e @ 0\mod_1197021908190_78.docx @ 16120 @ 3 @ 1

Note

No oil change is required on the cutter bar.

9.7.2 Checking the oil level

Pos: 18.24.5 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M esser trommel_2 @ 0\mod_1197022569252_78.docx @ 16165 @ @ 1

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

Lower guards. Nobody should be in the danger zone around the machine.

Pos: 18.24.6 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M esser trommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Pos: 18.24.7 /Ü berschriften/Ü berschriften 3/K-O/MM ähholm ausrichten @ 0\mod_1197017956815_78.docx @ 16042 @ 3 @ 1

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

9.7.3

Pos: 18.24.8 /BA/Wartung/Mähwerke/M ähhol m ausrichten EasyC ut @ 3\mod_1204721803648_78.docx @ 72358 @ @ 1

Aligning the Cutter Bar

Pos: 18.24.9 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 30

Oil level check

• Align the cutter bar using a spirit level (1).

Crosswise

• Lay the spirit level on top of the cutting disc hub parallel to the direction of travel.

Lengthwise

• Lay the spirit level (1) on top of two mower discs.

EC-0-001

50

Pos: 18.24.10 /BA/Wartung/M ähwer ke/Öl kontr olle M ähholm Easycut @ 3\mod_1204723206930_78.docx @ 72428 @ @ 1

Maintenance

• Allow the machine to run briefly. Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop

Pos: 18.25 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-0-003

Fig. 31:

Check the oil level before every use

• Remove the oil level inspection screw (1) from the cutting disc hub

• The oil level must be up to the bore hole. If required, top up the oil (SAE 90)

• Screw in the oil level inspection screw (1) again and tighten securely

51

Maintenance

Pos: 18.26.1 /Ü berschriften/Ü berschriften 2/K-O/KKontroll e der M ähklingen und Messer halterung @ 0\mod_1197265641329_78.docx @ 16323 @ 2 @ 1

9.8 Checking the Cutter Blades and Blade Holder

Pos: 18.26.2 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Fehl ende und beschädigte M ähklingen und M ähklingenhal ter ungen @ 0\mod_1197265722813_78.docx @ 16342 @ @ 1

Pos: 18.26.3 /Ü berschriften/Ü berschriften 3/K-O/MM ähkli ngen @ 0\mod_1197265959110_78.docx @ 16361 @ 3 @ 1

Warning! - Missing and damaged cutter blades and cutter blade retainers.

Effect: Danger to life, serious injuries or damage to the machine

• Check cutter blades at least once per day and check retaining bolts every time you change the blades or after contact with foreign objects.

• Immediately replace missing or damaged cutter blades and cutter blade retainers

9.8.1 Cutter Blades

Pos: 18.26.4 /BA/Wartung/Mähwerke/Di e Bohrung der M ähklingen kann sich durch Verschleiß aufweiten. @ 10\mod_1221048982715_78.docx @ 131675 @ @ 1 The borehole on the cutter blades may spread due to wear.

Pos: 18.26.5 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung - Z u geri nge M aterialstär ke an den Mähkling en_neu @ 312\mod_1418983956660_78.docx @ 2409555 @ @ 1

Danger! - Insufficient thickness of material on the cutter blades.

Pos: 18.26.6 /BA/Wartung/Mähwerke/M ähklingen beidseitig verwenbar_neu @ 3\mod_1204728012601_78.docx @ 72608 @ @ 1

Effect: Danger to life or serious injuries.

• The cutter blades must be replaced at the latest when the wear limit is reached (see mark

(1) on the cutter blade; dimension a less than or equal to 13 mm). a

1

EC 253 0

Fig. 32

Pos: 18.26.7 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note - The cutter blades can be turned around and used on both sides.

• When cutter blades are missing or damaged, they must be replaced as a complete set.

This prevents dangerous unbalanced rotation

52

Pos: 18.26.8 /BA/Wartung/Mähwerke/M esserschraub / M esserschnell verschl uss/M esserschraubverschluss H altebolzen 14 mm @ 0\mod_1197267907375_78.docx @ 16425 @ 3 @ 1

9.8.2 Blade screw connection

Maintenance

Danger! - Insufficient thickness of material on the retaining bolts.

Effect: Danger to life or serious injuries.

• At every blade changing check the thickness of the holding bolts material.

• Damage or worn retaining bolts must always be replaced by sets on each cutting disc/blade drum!

• The material thickness of the retaining bolts must not be less than 14 mm at the weakest point.

Pos: 18.26.9 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 33 min. 14 mm

EC-240-0

53

Maintenance

Pos: 18.26.10 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/M esserschnell verschluss H altebolzen 14mm @ 0\mod_1197268087875_78.docx @ 16444 @ 3 @ 1

9.8.3 Blade Quick-Fit Device

Danger! - Insufficient thickness of material on the retaining bolts.

Effect: Danger to life or serious injuries.

• At every blade changing check the thickness of the holding bolts material.

• Damage or worn retaining bolts must always be replaced by sets on each cutting disc/blade drum!

• The material thickness of the retaining bolts must not be less than 14 mm at the weakest point.

• The material thickness of the leaf spring must not be less than 3 mm at the weakest point.

min. 14 mm

EC-239-0

Fig. 34

Pos: 18.26.11 /Ü berschriften/Ü berschriften 3/P-T /PPrüfen der M aterialstär ke der H altebolzen US @ 8\mod_1219048913565_78.docx @ 108655 @ 3 @ 1

9.8.4 Checking the Material Thickness of the Retaining Bolts

Pos: 18.26.12 /BA/Wartung/M ähwer ke/Prüfen der M aterialstär ke der H altebolzen/Bl attfedern_US @ 8\mod_1219047827550_78.docx @ 108614 @ @ 1

2 1 a b

EC-241-0

Fig. 35

The material thickness of the retaining bolts and the leaf springs is checked using the supplied gauge (1). The gauge (1) is located on the special tool (2) {blade key}.

Section (a) of the gauge is used to check the material thickness of the retaining bolts.

Section (b) of the gauge is used to check the contour of the leaf springs.

Pos: 18.26.13 /BA/Wartung/M ähwer ke/M aterialstär ke der H altebolzen über prüfen U S @ 8\mod_1219048235081_78.docx @ 108634 @ 4 @ 1

54

9.8.4.1 Checking the material thickness of the retaining bolts

2

1

Maintenance

Pos: 18.26.14 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-242-0

Fig. 36

• Remove the cutter

• Clean the area to be checked

• Place the gauge (1) with section (a) against the retaining bolt (2).

• Rotate the gauge (1) by 90 degrees.

• If it is not possible to slide the gauge over the retaining bolt during the rotation, then the retaining bolt is still in working order.

• If it is possible to slide the gauge (2) over the retaining bolt during the rotation, the retaining bolt must be replaced immediately.

55

Maintenance

Pos: 18.26.15 /BA/Wartung/M ähwer ke/R egel mäßige Kontr olle der Bl attfeder n U S @ 8\mod_1219049253925_78.docx @ 108717 @ 3 @ 1

9.8.5 Periodical Inspection of the Leaf Springs

Danger! - Worn application seam on the leaf springs.

Effect: Danger to life or serious injuries.

• Check the leaf springs for damage at least once a day or after contact with foreign objects.

• The wear limit of the leaf springs is reached when the application seam (1) is worn away at one point. The wear limit must be checked with the gauge (2).

1 1

EC 225 0

Fig. 37

Note

Use only original Krone spare parts to replace the leaf springs.

Pos: 18.26.16 /Ü berschriften/Ü berschriften 3/P-T /PPrüfen der M aterialstär ke der Blattfeder n U S @ 8\mod_1219048953143_78.docx @ 108676 @ 3 @ 1

9.8.6 Checking the Material Thickness of the Leaf Springs

Pos: 18.26.17 /BA/Wartung/M ähwer ke/Prüfen der M aterialstär ke der H altebolzen/Bl attfedern_US @ 8\mod_1219047827550_78.docx @ 108614 @ @ 1

2 1 a b

EC-241-0

Fig. 38

The material thickness of the retaining bolts and the leaf springs is checked using the supplied gauge (1). The gauge (1) is located on the special tool (2) {blade key}.

Section (a) of the gauge is used to check the material thickness of the retaining bolts.

Section (b) of the gauge is used to check the contour of the leaf springs.

Pos: 18.26.18 /BA/Wartung/M ähwer ke/M aterialstär ke der Blattfedern überprüfen U S @ 8\mod_1219049061425_78.docx @ 108698 @ 4 @ 1

56

9.8.6.1 Checking the material thickness of the leaf springs

2

Maintenance

1

Pos: 18.26.19 /BA/Wartung/M ähwer ke/Blattfeder Kontur prüfen US @ 8\mod_1219049656846_78.docx @ 108739 @ @ 1

EC-243-0

Fig. 39

• Remove the cutter

• Clean the area to be checked

• Push the gauge (1) with section (b) over the retaining bolt of the leaf spring (2), as far as it will go.

1

2

IC

1

2 IIC

EC-244-0

Pos: 18.26.20 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 40

• If the contour of the leaf spring (2) in section (IC) aligns completely with the contour of the gauge (1), the leaf spring has not yet reached its wear limit.

• If the contour of the leaf spring disappears at any point in section (IIc) behind the contour of the gauge, the leaf spring has reached its wear limit. The leaf spring must be replaced.

57

Maintenance

Pos: 18.26.21 /BA/Wartung/M ähwer ke/R egel mäßige Kontr olle der Messerteller bzw. -trommeln @ 0\mod_1197268487390_78.docx @ 16483 @ 3 @ 1

9.8.7 Periodical Inspection of the Cutting Discs / Blade Drums

Danger! - Deformed Cutting Discs / Blade Drums

Effect: Danger to life or serious injuries.

• Check the cutting discs or blade drums for damages at least once per day or after contact with foreign objects.

• In case of deformed cuttings discs or drums, the dimension of A = 48 mm must never be exceeded.

1

A

EC-0-211

Fig. 41

Pos: 18.26.22 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

The cutting discs or drums must be replaced by Original Krone spare parts only.

58

Pos: 18.26.23 /BA/Wartung/M ähwer ke/Verschlei ssgrenze für Auswaschungen @ 0\mod_1197268738875_78.docx @ 16502 @ 3 @ 1

9.8.8 Abrasion Limit

Maintenance

Danger! - Abrasion on the cutting discs / blade drums

Effect: Danger to life or serious injuries.

• The abrasion limit (2) will be achieved if the min. material thickness of 3 mm is no longer given.

2

2

Pos: 18.26.24 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-226-0

Fig. 42

Note

If cutting discs or blade drums show deformations or wear in form of abrasions (2) or similar, these components have to be replaced by Original Krone spare parts .

59

Maintenance

Pos: 18.26.25 /Ü berschriften/Ü berschriften 2/K- O/MMesser wechsel an M essertell ern @ 0\mod_1197269068562_78.docx @ 16521 @ 2 @ 1

9.9 Blade Changing on Cutting Discs

Pos: 18.26.26 /BA/Sicher hei t/7. Gefahrenhinweise alt/Mähwer ke/Gefahr - Schnell rotier ende Messer teller /Messertr ommel n_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

Pos: 18.26.27 /BA/Sicher hei t/7. Gefahrenhinweise alt/Mähwer ke/Gefahr - Sich lösende M ähklingen @ 0\mod_1197269483265_78.docx @ 16540 @ @ 1

Pos: 18.26.28 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Danger! - Cutter blades coming loose

Effect: Danger to life or serious injuries.

• After changing the blades check that they fit perfectly and that they can move freely.

• Whenever a blade is changed, also inspect the fasteners and replace them, if necessary!

• Always replace missing and damaged blades in sets to prevent unbalanced rotation!

• Never mount unevenly worn blades on a drum/disc!

60

Pos: 18.26.29 /Ü berschriften/Ü berschriften 3/K- O/MMesserschr aubverschl uss @ 0\mod_1197270941296_78.docx @ 16578 @ 3 @ 1

9.9.1 Blade Screw Connection

Pos: 18.26.30 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/Beschr eibung M esser wechsel M esserschr aubverschl uss @ 47\mod_1285661949953_78.docx @ 456898 @ @ 1

Maintenance

EC-0-250

Pic. 43

• Fold up safety device

• Clean the area

• Remove damaged or worn blades

• To fit the blades, insert the blade (5) between the wear skid (2) and the cutting disc (1)

• Insert the retaining bolt (3) from below through the wear skid, the blade and the cutting disc

• Place the locknut (4) on the retaining bolt from above and tighten it firmly (tightening torque refer to chapter “Torques”)

• Repeat the process for all blades

• After fitting the blades, fold the safety device down again

Note

• The cutter blades of anticlockwise rotating cutting discs / blade drums are different to those of clockwise rotating ones. Make certain the direction of rotation is correct when installing!

• The arrow on the cutter blades must match the direction of rotation of the corresponding cutting discs / blade drums

• The locknut (4) used to secure the retaining bolts must not be used more than once

Order No. for clockwise rotating blade: 139-889

Pos: 18.26.31 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Order No. for anticlockwise rotating blade: 139-888

61

Maintenance

Pos: 18.26.32 /Ü berschriften/Ü berschriften 3/K- O/MMesserschnell verschluss @ 0\mod_1197271019859_78.docx @ 16597 @ 3 @ 1

9.9.2 Blade Quick-Fit Device

Pos: 18.26.33 /BA/Wartung/M ähwer ke/M esserschr aub / M esserschnellverschluss/Beschr eibung M esser wechsel M esserschnellverschluss @ 0\mod_1197271100500_78.docx @ 16616 @ @ 1

2 3 4

5

EC-251-0

Fig. 44

• Clean the area.

• Remove damaged or worn blades.

• Push the special tool (1) {blade key} between the cutter disc (4) and leaf spring (3) and press down with one hand.

• Guide a new blade (2) onto the retaining bolt and allow the blade key to return upwards.

• After fitting the blades, fold the protective device down again.

Note

• The cutter blades of anticlockwise rotating cutting discs / blade drums are different than those of clockwise rotating ones. Make certain the direction of rotation is correct when installing!

• The arrow on the cutter blades must match the direction of rotation of the corresponding cutting discs / blade drums.

• The hex nut (4) used to secure the retaining bolts must not be used more than once.

Order No. for clockwise rotating blade: 139-889

Pos: 18.26.34 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Order No. for anticlockwise rotating blade: 139-888

62

Pos: 18.26.35 /BA/Wartung/M ähwer ke/Stoß kanten erneuern @ 0\mod_1197271320468_78.docx @ 16636 @ 2 @ 1

9.10 Replacing the linings

Maintenance

Caution! - If the linings are checked irregularly.

Effect: Damage to the machine

• Always check the mowing unit for damaged linings prior to start-up and replace linings, if necessary!

• Adjust the welding current and the welding material to the cutter bar material and to the lining or carry out a trial welding if necessary.•

EC-0-012

Fig. 45

• Open the welding seams of the old lining.

• Remove the lining

• Deburr the contact surface.

Pos: 18.27 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-252-0

Fig. 46

• Adapt the new lining (3).

• Weld short I seams on the upper surface of the cutter bar in the areas marked (1) (each should be approx. 30 mm).

• Do not weld the edges (2).

• On the

lower surface

of the cutter bar, weld the lining (3) to the cutter bar along the whole length in area (5).

• Do not weld the edges (4).

63

Maintenance

Pos: 18.28 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Pos: 18.29.1 /Ü berschriften/Ü berschriften 2/K-O/KKr eisel nabe mit Schersicherung (opti onal) @ 4\mod_1213097920976_78.docx @ 86356 @ 2 @ 1

9.11 Rotary hub with shear fuse (optional)

Pos: 18.29.2 /BA/Wartung/Mähwerke/Schersicherung/Bil d Mähhol m Aufstellung EC 28/32 P EC 28/32M @ 15\mod_1232448431683_78.docx @ 174012 @ @ 1

Fig. 47:

Pos: 18.29.3 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

64

Pos: 18.29.4 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/Gefahr - Schnell r oti erende M esserteller/M esser trommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Maintenance

Danger! - Rapidly rotating cutting discs/blade drums.

Effect: Danger to life or serious injuries.

• Switch off the engine and remove the ignition key.

• The cutting discs/blade drums continue to run!

• Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete stop.

Pos: 18.29.5 /BA/Wartung/Mähwerke/Schersicherung/Legende M ähhol m Aufstellung EasyC ut´s A,B,RZ,RE,LZ,LE @ 4 \mod_1213098609195_78.docx @ 86463 @ @ 1

Explanation of abbreviations:

A= Direction of rotation "A" to the middle

B= Direction of rotation "B" in pairs

RZ= Central bearing housing (clockwise threading), without identifying groove.

RE= Eccentric bearing housing (clockwise threading, without identifying groove).

LZ= Central bearing housing (anticlockwise threading), with identifying groove.

LE= Eccentric bearing housing (anticlockwise threading), with identifying groove.

Pos: 18.29.6 /BA/Wartung/Mähwerke/Schersicherung/Beschrei bung Schersicher ung RZ ,RE,LZ ,LE @ 3 \mod_1204205493155_78.docx @ 69964 @ @ 1 For protection against overload on the mowing units, the rotary hubs (1) are secured with nuts

(2) and shear pins (3).

If the machine strikes obstacles (for example stones), the 2 shear pins in the rotary hub will be sheared off. The rotary hub and nut turn upward on the pinion shaft.

• The cutting discs or drums which move crop to the left (as seen in the direction of travel)

(LE/LZ) have left-handed threading.

• The cutting discs or drums which move crop to the right (in the direction of travel) (RE/RZ) have right-handed threading.

To distinguish between right-hand (clockwise) threading (RE/RZ) and left-hand (anti-clockwise) threading (LE/LZ), the nuts (2) and pinion shaft (4) for left-hand threading (LE/LZ) have a distinctive grove (a, b).

• Left-handed (LE/LZ) nuts (2) have distinctive grooves (a) on the bevel.

• Left-handed (LE/LZ) pinion shafts (4) have a distinctive groove (b) on the face.

Pos: 18.29.7 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

65

Maintenance

Pos: 18.29.8 /BA/Wartung/Mähwerke/SchersicherungNach dem Abscher en EasyC ut @ 364 \mod_1440501433026_78.docx @ 2678607 @ 3 @ 1

9.11.1 After Shearing Off

Caution! - Correct installation position of the bearing housing not observed.

Effect: Damage to the machine

• Right rotating (RE/RZ) cutting discs and drums always have right-handed pinion shafts and nuts (no groove mark on the pinion shaft and nut).

• Left rotating (LE/LZ) cutting discs and drums always have left-handed pinion shafts and nuts

(with groove mark on the pinion shaft and nut).

7

8 a

9

2

3

3a

3a

3

3a

4 d b

1 c

10

EC-255-1

Fig. 48

66

Maintenance

• Remove the cutting disc or drum.

• Remove retaining ring (7).

• Unscrew the hexagon head bolts (8).

• Use the special key (10) included with delivery to remove the nut (2).

• Remove the hub (1).

• Remove the damaged shear pins (3).

• Check the nut and hub for damage. Replace damaged parts with KRONE original replacement parts.

• Fill the space above the bearing with grease (c).

• Place the hub on the pinion shaft.

• Drive the new shear pins (3) through the hub (1) and shaft (4).

Pos: 18.30 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note - Note the position of the shear pins!

• Drive the shear pins (3) into the hole from outside until the end of the pin reaches the surface of the hub (d).

• he slots of the shear pins (3) must be mounted facing each other horizontally (see detail (I)).

• Install the nut (2) using the special key (10) included with delivery (tighten to a tightening torque of 300 Nm).

• Install and tighten the hexagon head bolts (8) with detent edged washers.

• Install the retaining ring (7).

• Install the cutting disc (5) or blade drum (6).

67

Maintenance – lubrication chart

Pos: 18.31.1 /Ü berschriften/Ü berschriften 1/U-Z/Wartung - Schmierpl an @ 0\mod_1197359304198_78.docx @ 18232 @ 1 @ 1

10

Pos: 18.31.2 /Ü berschriften/Ü berschriften 2/P-T/SSpezi elle Sicher hei tshi nweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Maintenance

– lubrication chart

10.1 Special Safety Instructions

Pos: 18.31.3 /BA/Sicherheit/7. Gefahr enhinweise alt/M ähwer ke/War nung - R eparatur _Wartung_R einigungs_4 allgemei n EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1

Pos: 18.31.4 /Ü berschriften/Ü berschrif ten 2/F-J/GGel enkwelle @ 0\mod_1199781879794_78.docx @ 34542 @ 2 @ 1

WARNING!

When performing repair, maintenance or cleaning work or in case of technical intervention, drive elements may start moving (caution: cutting discs continue to run).

Effect: Danger to life, injuries or damage to the machine.

• Turn off the PTO shaft.

• Move the machine to the working position and lower it to the ground.

• Switch off the engine of the tractor, remove the ignition key and carry it with you.

• Secure the tractor against accidental start-up and against rolling.

• After the repair, maintenance, cleaning work or technical modifications are completed, mount all protective covers and safety devices properly again.

• Avoid skin contact with oils, greases, cleaning agents and solvents.

• In the event of injuries or burns due to oils, cleaning agents or solvents, contact a physician immediately.

• All other safety instructions must also be followed to avoid injuries and accidents.

10.2 PTO shaft

Pos: 18.31.5 /BA/Wartung/Gelenkwelle schmi eren/Abschmi eren Gel enkwelle EasyC ut 100 h @ 44\mod_1275544141265_78.docx @ 392033 @ @ 1

Pos: 18.31.6 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Fig. 49

Lubricate the PTO shafts at the intervals indicated in the drawing with a multi-purpose grease.

Follow the operating instructions of the PTO shaft manufacturer.

68

Pos: 18.31.7 /Ü berschriften/Ü berschriften 2/P-T/SSchmier plan @ 0\mod_1197361829026_78.docx @ 18495 @ 2 @ 1

10.3 Lubrication Chart

Pos: 18.31.8 /Abkürzungen /Abkürzung en spr achneutral/EasyC ut/EasyCut 28 P, EasyC ut 28M, EasyC ut 32 P, EasyCut 32 M @ 10\mod_1221742126208_0.docx @ 137262 @ @ 1

(EasyCut 28 P, EasyCut 28 M, EasyCut 32 P, EasyCut 32 M)

Pos: 18.31.9 /BA/Wartung/Mähwerke/EasyC ut / AM Mähwerke/Schmier pläne/Schmi erplan Bild EC 28/32 @ 10\mod_1221741987395_78.docx @ 137240 @ @ 1

Maintenance – lubrication chart

20h

20h

Fig. 50:

Pos: 19 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-228-0

69

Placing in Storage

Pos: 20.1 /Überschriften/Überschriften 1/A-E/Ei nlag erung @ 0\mod_1197385459120_78.docx @ 19966 @ 1 @ 1

11 Placing in Storage

Pos: 20.2.1 /BA/Einl agerung/M aschine an ei nem trockenem Ort abstellen @ 70\mod_1305630069850_78.docx @ 638292 @ @ 1

• Park the machine in a dry location, but not in the vicinity of artificial fertilisers or livestock buildings.

Pos: 20.2.2 /BA/Einl agerung/Vor der Ei nwinter ung die Maschi ne innen und auß en gr ündlich reinig en @ 70\mod_1305635346852_78.docx @ 638460 @ @ 1

Pos: 20.2.3 /BA/Einl agerung/Gel enkwelle auseinanderziehen und ei nfetten @ 70\mod_1305631424563_78.docx @ 638348 @ @ 1

• Before placing the machine in winter storage, clean inside and outside thoroughly. If you use a high-pressure cleaner to do this. do not keep a stream of water directed at bearing points. After cleaning is completed, lubricate all lubrication points. Do not wipe off any grease that comes out of bearing points. The hardened grease will provide additional protection against moisture.

• Disassemble the PTO shaft. Lubricate the inner tubes and the guard tube with grease.

Grease the lubrication points on the cross joint and on the bearing rings of the guard tubes.

Pos: 20.2.4 /BA/Einl agerung/Alle Gel enkstellen einölen @ 70\mod_1305633347429_78.docx @ 638432 @ @ 1

• Oil all joint points!

Pos: 20.2.5 /BA/Einl agerung/Lackschäden ausbesser n, blanke Stellen gründlich mit R ostschutzmittel konser vi eren @ 70\mod_1305630900253_78.docx @ 638320 @ @ 1

• Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection agent.

Pos: 20.2.6 /BA/Einl agerung/Alle beweglichen Bauteile über prüfen @ 70\mod_1305632768685_78.docx @ 638404 @ @ 1

Pos: 20.2.7 /BA/Einl agerung/Ver wenden Si e nur Original-KR ONE- Ersatzteile @ 70\mod_1305632212285_78.docx @ 638376 @ @ 1

• Check all movable components such as deflector rollers, joints, tension rollers, etc. to make certain they move easily. If necessary remove, clean, grease and remount. If necessary, replace with new parts.

• Use only original KRONE replacement parts.

Pos: 20.2.8 /BA/Einl agerung/Sammelliste erstell en @ 70\mod_1305626681125_78.docx @ 638264 @ @ 1

Perform the necessary repair tasks during the time immediately after the harvest season. Draw up a list of all replacement parts you will need. This will make it easier for your KRONE dealer to process your orders and you will be certain that your machine will be ready for use at the beginning of the next season.

Pos: 20.3 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

70

Pos: 20.4 /Überschriften/Überschriften 1/U-Z/Vor Beginn der neuen Saison @ 4\mod_1211272647559_78.docx @ 82867 @ 1 @ 1

Before the Start of the New Season

12

Pos: 20.5 /Überschriften/Überschriften 2/P-T/SSpeziell e Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Before the Start of the New Season

12.1 Special Safety Instructions

Pos: 20.6 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - R epar atur _Wartung_R einigungs_4 allgemei n EasyCut (2014- 09- 17 10:10:25) @ 11\mod_1223620198301_78.docx @ 148349 @ @ 1

Danger! - When performing repair, maintenance or cleaning work on the machine, or in the case of technical intervention, drive elements may start moving (caution, the cutting discs continue to run).

Effect: Danger to life, injuries or damage to the machine.

• Move the machine to the working position and lower it to the ground

• Switch off the tractor engine and remove the ignition key.

• Secure the tractor against accidental start-up and against rolling.

• Switch off the PTO and disengage it.

• After repair, maintenance, cleaning work or technical modifications are complete, mount all protective coverings and safety devices again properly.

• Avoid skin contact with oils, greases, cleaning agents and solvents.

• In the event of injuries or burns due to oils, cleaning agents or solvents, contact a doctor immediately.

• All other safety instructions must also be followed to avoid injuries and accidents.

Pos: 20.7 /Überschriften/Überschriften 2/P-T/PPr obel auf @ 0\mod_1196782963921_78.docx @ 14908 @ 2 @ 1

12.2 Test run.

Pos: 20.8 /BA/Sicher heit/7. Gefahrenhi nweise alt/Mähwer ke/Gefahr - Probel auf Einzahl Mähwer k muss auf Boden auflieg en @ 11\mod_1223615241207_78.docx @ 148217 @ @ 1

Danger! - Testing the machine after repair, maintenance or cleaning work and after technical intervention.

Effect: Danger to life or serious injuries

• The mowing unit must be in working position

• Do not switch on the drives until the mowing unit is resting on the ground and you are absolutely sure that neither persons, animals nor objects are in the danger zone.

• Start a trial run of the machine only from the driver’s seat.

Pos: 20.9 /BA/Einl agerung/EasyCut / AM M ähwer ke/Vor der Saison ohne Bereifung @ 3\mod_1204731533226_78.docx @ 72767 @ @ 1

• Lubricate the machine thoroughly. Remove any condensation water which may have collected in the bearings.

• Check oil level in the gearbox(es) and top up if necessary.

• Check all screws to make certain they are tight or retighten them if necessary.

• Check all electrical connection cables and the lighting. Repair or replace if necessary.

• Check the entire setting of the machine and correct if necessary.

• Re-read the operating instructions thoroughly.

Note

Use vegetable oils and greases.

Pos: 21 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

71

Special equipment

Pos: 22 /Ü berschriften/Überschriften 1/P-T/Sonder ausstattung @ 2\mod_1202808469779_78.docx @ 61649 @ 1 @ 1

13

Pos: 23 /Ü berschriften/Überschriften 2/P-T/SSpeziell e Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

Special equipment

13.1 Special Safety Instructions

Pos: 24 /BA/Sicher heit/7. Gefahrenhi nwei se alt/Mähwer ke/Warnung - Repar atur_Wartung_R ei nigungs_4 allgemein EasyC ut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1

WARNING!

When performing repair, maintenance or cleaning work or in case of technical intervention, drive elements may start moving (caution: cutting discs continue to run).

Effect: Danger to life, injuries or damage to the machine.

• Turn off the PTO shaft.

• Move the machine to the working position and lower it to the ground.

• Switch off the engine of the tractor, remove the ignition key and carry it with you.

• Secure the tractor against accidental start-up and against rolling.

• After the repair, maintenance, cleaning work or technical modifications are completed, mount all protective covers and safety devices properly again.

• Avoid skin contact with oils, greases, cleaning agents and solvents.

• In the event of injuries or burns due to oils, cleaning agents or solvents, contact a physician immediately.

• All other safety instructions must also be followed to avoid injuries and accidents.

Pos: 25 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

72

Pos: 26.1 /BA/Sonder ausstatung/EasyCut / AM M ähwer ke/U mbau auf schmaler e Schwadabl age EC 28/32 M @ 13 \mod_1226923435912_78.docx @ 166497 @ 2 @ 1

13.2 Conversion to narrower swathing

Special equipment

(EasyCut 28 M, EasyCut 32 M) / (EasyCut F 280 M, EasyCut F 320 M)

1

2

3

5 6

5

EasyCut 28M / EasyCut F 280 M

6

3 4

4

4 4

EasyCut32M / EasyCut F 320 M

4 4

EC-281-0

Fig. 51

• Remove the cutting discs (5) and covers (6).

• Remove cover (3) of mower drum (4). Mount the mower drum with fastening bolts and the detent edged washers of the disassembled cutting discs (6).

• Mount the cover (3) on the mower drum (4).

Note

Keep the cover (5) and cutting disc (6) in a suitable place for later reinstallation.

Warning - Mower drum incorrectly installed

Effect: Damage to the machine

Make certain the mower drums are installed correctly! The installed mower drums (4) must be installed at a 90-degree offset to the adjacent mower drums / cutting discs.

73

Special equipment

• Install the plates (1,2). Make certain when attaching the plates that the distance from the rubber pads (7) to the mower drums is at least 3 mm.

Pos: 26.2 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note - Reinstallation is in the reverse order

Before starting up the machine again, make certain to check the cutter blades, retaining bolts, cutting discs, and drums as well as the linings

See Maintenance section “Checking the Cutter Blades and Retaining Bolts”.

See Maintenance section “Periodical Inspection of Cutting Discs and Drums."

See Maintenance section “Replacing the Linings".

74

Pos: 26.3 /BA/Sonder ausstatung/EasyCut / AM M ähwer ke/U mbau für steiles Bergabmähen EC 28 M/32M @ 13\mod_1226927794381_78.docx @ 166544 @ 2 @ 1

13.3 Conversion for mowing steep slopes

Special equipment

(EasyCut 28 M, EasyCut 32 M) / (EasyCut F 280 M, EasyCut F 320 M)

1

2

4 3

4

3

EasyCut 28M / EasyCut F 280 M

5

6

5 6

EasyCut32M / EasyCut F 320 M

5 5

5 5

Pos: 27 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

EC-254-1

Fig. 52

• Remove plates (1,2)

• Remove cover (3) of mower drum (4).

• Remove mower drum (4).

Note

Keep the plates (1,2), cover (3) and mower drums (4) in a protected place for later reinstallation.

Warning - Cutting disc installed incorrectly

Effect: Damage to the machine

Make certain the cutter discs are installed correctly! The installed cutting discs (5) must be installed at a 90-degree offset to the adjacent mower drums / cutting discs.

• Mount the cutting discs (5) and covers (6). To do this, reuse the fastening bolts and detent edged washers of the mower drums that were removed.

Note

Follow the steps in the reverse order for reinstallation (see also Chapter "Conversion to

Narrower Swathing").

Before starting up the machine again, make certain to check the cutter blades, retaining bolts, cutting discs, and drums as well as the linings

• See Maintenance section "Checking the Cutter Blades and Retaining Bolts".

• See Maintenance section "Periodical Inspection of Cutting Discs and Drums."

• See Maintenance section "Replacing the Linings".

75

Disposal of the machine

Pos: 28 /Ü berschriften/Überschriften 1/A-E/Entsorgung der M aschine @ 274\mod_1404207309028_78.docx @ 2060455 @ 1 @ 1

14

Pos: 29 /BA/Entsorgung der Maschi ne/Die M aschine entsorgen @ 274\mod_1404207434449_78.docx @ 2060544 @ 2 @ 1

Disposal of the machine

14.1

=== Ende der Liste für T extmar ke Inhalt ===

Disposal of the machine

After the service life of the machine has expired, the individual components of the machine must be disposed of properly. The applicable country-specific, current waste disposal guidelines and the legal laws must be observed.

Metal parts

All metal parts must be brought to a metal recycling centre.

The components must be freed from operating fluids and lubricants (gear oil, oil from hydraulic system, ...) before being scrapped.

The operating fluids and lubricants must be brought separately to an environmentally friendly disposal point or recycling centre.

Operating fluids and lubricants

Operating fluids and lubricants (diesel fuel, coolant, gear oil, oil from hydraulic system, ...) must be brought to a disposal point for waste oil.

Synthetic materials

All synthetic materials must be brought to a recycling centre for synthetic materials.

Rubber

Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre.

Electronic scrap

Electronic parts must be brought to a disposal point for electronic scrap.

76

15 Index

A

Abrasion Limit ..................................................... 59

Adjusting the Compensation Springs ................. 40

Adjusting the cutting height ................................ 41

After Shearing Off ............................................... 66

Aligning the Cutter Bar ........................................ 50

Angular gearbox ................................................. 48

Attached devices ................................................ 11

B

Before mowing .................................................... 34

Before the Start of the New Season ................... 71

Blade Changing on Cutting Discs ....................... 60

Blade Quick-Fit Device ................................. 54, 62

Blade screw connection ...................................... 53

Blade Screw Connection .................................... 61

C

Checking the Cutter Blades and Blade Holder ... 52

Checking the First fitting ..................................... 25

Checking the material thickness of the leaf springs

........................................................................ 57

Checking the Material Thickness of the Leaf

Springs ............................................................ 56

Checking the material thickness of the retaining bolts ................................................................ 55

Checking the Material Thickness of the Retaining

Bolts ................................................................ 54

Clamp and Buffer ................................................ 33

Commissioning ................................................... 18

Compensation Spring(s) ..................................... 39

Connecting the hydraulic lines ............................ 30

Contact for KRONE NORTHAMERICA ................ 5

Conversion for mowing steep slopes .................. 75

Conversion to narrower swathing ....................... 73

Cutter Blades ...................................................... 52

D

Dangers in Case of Non-compliance with the

Safety Instructions .......................................... 10

Detaching the machine ....................................... 36

Deviating Tightening Torques ............................. 46

Disposal of the machine ..................................... 76

Driving and Transport ......................................... 32

F

Filling Quantities and Lubrication Designations for

Gearboxes ...................................................... 47

First installation ................................................... 18

Fitting the guard cloths ....................................... 19

Index

H

Hydraulic system ................................................ 12

Hydraulics .......................................................... 30

I

Identification Plate ................................................ 6

Identifying Symbols in the Operating Instructions 8

Inadmissible Modes of Operation ...................... 13

Information Required for Questions and Orders .. 6

Install the PTO shaft .......................................... 27

Installation of Weiste triangle ............................. 20

Intended use ........................................................ 7

Introduction .......................................................... 5

L

Lighting ........................................................ 21, 32

Lighting connection ............................................ 29

Lower suspension arm ....................................... 24

Lubrication Chart ................................................ 69

M

Maintenance ................................................ 12, 43

Maintenance – lubrication chart ......................... 68

Metric Thread Screws with Control Thread ....... 44

Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 45

Metric Thread Screws with Fine Thread ............ 45

Mounting and adjusting the relief springs .......... 28

Mounting onto the Tractor .................................. 23

Moving the guards into the working position ..... 35

Mower Drive Gearbox ........................................ 49

O

Oil Level Check and Oil Change Intervals

(Gearboxes) ................................................... 47

Oil level check and oil change on the cutter bar 50

Operation ........................................................... 34

P

Periodical Inspection of the Cutting Discs / Blade

Drums............................................................. 58

Periodical Inspection of the Leaf Springs .......... 56

Personnel Qualification and Training ................. 10

Placing in Storage .............................................. 70

Position of the Adhesive Safety Stickers on the

Machine ......................................................... 14

Preparation on the front-mounted disc mower .. 20

PTO operation .................................................... 11

PTO shaft ..................................................... 26, 68

Purpose of Use .................................................... 5

77

R

Removing the compensation spring(s) ............... 36

Replacing the linings ........................................... 63

Rotary hub with shear fuse (optional) ................. 64

S

Safety .................................................................... 8

Safety Instructions and Accident Prevention

Regulations ....................................................... 9

Safety-conscious work practices ........................ 10

Setting of the V-belt Tension .............................. 42

Settings ............................................................... 38

Spare Parts ......................................................... 44

Special equipment ............................................. 72

Start-up .............................................................. 22

T

Technical data ...................................................... 7

Telescopic upper suspension arm ..................... 41

Test run .............................................................. 71

Test run .............................................................. 43

Tightening torques ............................................. 44

U

Unauthorised Conversion/Modification and Spare

Parts Production ............................................ 13

78

Maschinenfabrik

Bernard Krone GmbH & Co. KG

Heinrich-Krone-Straße 10, D-48480 Spelle

Postfach 11 63, D-48478 Spelle

Phone +49 (0) 59 77/935-0

Fax +49 (0) 59 77/935-339

Internet: http://www.krone.de

eMail: [email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Robust construction for durability
  • Efficient and precise cutting performance
  • EasyCut 28 and 32 models available in P(Plastic guards) and M(Metal guards) variants

Related manuals

Frequently Answers and Questions

What is the purpose of using different guard materials (Plastic and Metal) in EasyCut models?
Plastic guards offer lighter weight, while metal guards provide higher durability in demanding conditions.
Can I use the disc mower for cutting tall or dense grass?
Yes, the disc mower is designed to handle various grass conditions, including tall and dense grass.
What safety precautions should I follow when operating the disc mower?
Refer to the safety instructions in the user manual, including wearing appropriate protective gear and ensuring proper PTO operation.

advertisement

Table of contents