- No category
advertisement
SERVICE MANUAL
CDP-XA50ES
AEP Model
E Model
Photo: Black
Model Name Using Similar Mechanism
CD Mechanism Type
Base Unit Name
Optical Pick-up Name
NEW
CDM32BB-12B (BLACK)
CDM32BN-12B (GOLD)
BU-12B
KSS-273B/J1N
SPECIFICATIONS
– Continued on next page –
COMPACT DISC PLAYER
MICROFILM
MODEL IDENTIFICATION
– BACK PANEL –
4-986-742-
AEP Model : 1 π (CED)
Singapore Model : 2 π (SP)
TABLE OF CONTENTS
1.
SERVICING NOTES
1-1.
How to Open the Disc Tray When Power Switch
Turns Off .......................................................................... 3
1-2.
Preparation for Adjustment and Measurement ................ 3
2.
GENERAL
................................................................... 4
3.
DISASSEMBLY
.......................................................... 15
4.
TEST MODE
4-1.
AF Mode .......................................................................... 20
4-2.
ADJ Mode ....................................................................... 21
4-3.
CLV-S Mode .................................................................... 21
5.
ELECTRICAL ADJUSTMENTS
......................... 22
6.
DIAGRAMS
6-1.
Printed Wiring Boards — SERVO Section — ................. 25
6-2.
Schematic Diagram — SERVO Section — ..................... 27
6-3.
Schematic Diagram — AUDIO Section — ..................... 32
6-4.
Printed Wiring Boards — AUDIO Section — ................. 37
6-5.
Printed Wiring Boards — PANEL Section — ................. 39
6-6.
Schematic Diagram — PANEL Section — ..................... 41
6-7.
Printed Wiring Boards
— POWER SUPPLY Section — ..................................... 44
6-8.
Schematic Diagram
— POWER SUPPLY Section — ..................................... 47
6-9.
IC Pin Function Description ............................................ 54
7.
EXPLODED VIEWS
................................................ 60
8.
ELECTRICAL PARTS LIST
................................ 66
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
– 2 –
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.
The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270 ˚C during repairing.
•
Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
SECTION 1
SERVICING NOTES
1-1.
HOW TO OPEN THE DISC TRAY WHEN
POWER SWITCH TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and turn in the direction of arrow (to OUT direction).
tray tapering driver
*
To close the disc tray, turn the tapering driver in the reverse direction (to IN direction).
1-2.
PREPARATION FOR ADJUSTMENT AND
MEASUREMENT
Perform connecting the IC261 pin 2 of SERVO board to the line of +5V because this unit does not work without the stabilizer structurally.
[SERVO BOARD] – Conductor side –
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
IC91
+5 V
IC101
1
IC261
2
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
The following caution label is located inside the unit.
– 3 –
This section is extracted from instruction manual.
SECTION 2
GENERAL
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –
– 10 –
– 11 –
– 12 –
– 13 –
– 14 –
• This set can be disassembled in the order shown below.
SECTION 3
DISASSEMBLY
LOADING PANEL SECTION
(Page 15)
CASE (TOP PLATE ), FRONT PANEL SECTION
(Page 16)
MECHANISM DECK (CDM32BB-12B/CDM32BN-12B)
(Page 17)
SERVO BOARD
(Page 17)
AUDIO BOARD
(Page 16)
PANEL (DRAWER)
(Page 18)
BASE UNIT (BU-12B)
(Page 18)
SLED MOTOR (M21), OPTICAL PICK-UP (KSS-273B/J1N)
(Page 19)
Note:
Follow the disassembly procedure in the numerical order given.
LOADING PANEL SECTION
5 connector
(CN292)
4 loading panel section tray
3 two hexagon hole bolts
(LID) (for black/gold)
1
Open the tray turning the tapering screwdriver to the arrow direction.
2 two screws
(KTP3
×
8) (for black/gold)
– 15 –
CASE (TOP PLATE), FRONT PANEL SECTION
1 three flat head screws
9 three connectors
(CN351, 352, 461)
1 three flat head screws
2 case (top plate)
3 two connectors
(CN201,
993)
6 four screws
(3
×
8)
7 two brakets (case)
4 screw
(3
×
8)
0 front panel section
8 two screws
(K3
×
8)
AUDIO BOARD
5 lag
3 two connectors
(CN922, 923)
3 four connectors
(CN103, 104, 105, 202)
3 two connectors
(CN202, 203)
4 two screws
(3
×
8)
4 four screws
(3
×
8)
4
TR screw
6 eight screws
(BV3
×
8 B)
3 two connectors
(CN401, 501)
5 lag
3 four connectors
(CN402, 502, 610, 611)
7 audio board
3 two connectors
(CN608, 609)
2 side plate (R)
– 16 –
1 four flat head screws
MECHANISM DECK (CDM32BB-12B/CDM32BN-12B)
2 two screws
3 clamp
2 two screws
3 clamp
4 mechanism deck
(CDM32BB-12B)
(CDM32BN-12B)
1 connector
(CN952)
1 connector
(CN105)
SERVO BOARD
1 two screws
(BVTP3
×
6)
2 bracket (servo)
1 two screws
(BVTP3
×
6)
5 six screws
(BVTP3
×
6)
1 two connectors
(CN103, 104)
3 wire (flat type) (26 core)
(CN102)
4 wire (flat type)
(12 core)
(CN101)
6 servo board bracket (servo)
– 17 –
PANEL (DRAWER)
3
Remove the panel (drawer) to direction of the arrow.
1 two tapping screws
2 two ditch
BASE UNIT (BU-12B)
5 two holders (SP)
4 two screws
(PTPWH2.6
×
8)
6 base unit
7 flexible board
(CN291)
7 two coil springs (F)
3 lag
4 two screws
(PTPWH2.6
×
8)
5 two holders (SP)
1 flexible board
(CN192)
7 two coil springs (F)
2 screw (B2.6
×
10)
– 18 –
SLED MOTOR (M21), OPTICAL PICK-UP (KSS-273B/J1N)
2 two screws
(BTP2.6
×
8)
7 poly-slider washer
8 gear (D)
4 tapping screw
5 lag
3 leaf spring (skew)
6 leaf spring (OP)
9
Remove the sled motor (M21) and optical pick-up
(KSS-273B/J1N) to direction of the arrow
A
.
A
0 bracket (OP base)
1 flexible board
(CN11)
4 tapping screw
– 19 –
SECTION 4
TEST MODE
4-1.
AF MODE
Connect the TP2 (AFJ) on the SERVO board to the ground and turn on the power supply.
The AF mode is then activated and the following check can be made.
REPEAT button
MIN
SIDE-B
( TIME )
C. FILE
4-1-1.
Fluorescent Indicator Tube Check
After confirming display of all on, keep pressing the following button, and the following display is attained.
•
INDEX
TIME button p (STOP) button
(Display: 01)
” (PLAY) button
P
(PAUSE) button
(Display: 02)
(Display: 03)
) button
SHUFFLE REPEAT A-
AUTO SPACE
STEP
–
0 button
1
B
PROGRAM
INDEX PEAK
EDIT
(Display: 04)
( JUST )
(Display: 05)
CHECK button
1 3 5
7 9
11 13 15
(Display: 06)
CLEAR button
6
2
12
8
P MODE button
SIDE-A
FADE
C.
SEC
DELETE
CUSTOM INDEX
4
14
10
”
(Display: 07)
(Display: 08)
(Display: 10)
Keep pressing the
§OPEN/CLOSE button, and all on display is attained again.
4-1-2.
Key Check
All buttons are assigned with numbers respectively, and when each button is pressed, it is counted and its number is displayed. Up to
“16” can be counted.
A button pressed once is not further counted but the number is displayed.
Button
ERASE
EDIT/
TIME FADE
FILE
FILTER
PUSH ENTER
§
OPEN/CLOSE p
(
Table 4-1.
Display
00
Button
P
12
13
20
23 all light up
01
02
)
0
CHECK
CLEAR
P MODE
REPEAT
TIME
Display
03
04
05
06
07
08
09
10
4-1-3.
Remote Commander Check
Press the
( button on remote commander, and “ ˚ ” ( on the set turn on. Nothing will be displayed if pressing another button.
count display
(1)
(Display: 09) button number display
– 20 –
4-2.
ADJ MODE
Connect the TP1 (ADJ) on the SERVO board to the TP (GND) and turn on the power supply. The ADJ mode is then activated and the following operation is executed.
• There is no problem even if GFS is low value continuously during playing.
• Do not perform high speed search during an access.
• The gain of focus servo and spindle servo does not lower during playing.
• Manual operation and measurement of the servo system are possible. (For detailed operating method, see Table 4-2. in ADJ
Mode.)
Button No.
3
8
11
12
17
18
19
13
14
15
16
20
4-2-1.
Button Operation Table in ADJ Mode
After all music numbers are displayed, press the TIME button, and the jitter display mode is then set. The button functions are as listed below.
Button Functions (Operate with remote commander.)
Table 4-2.
Test Mode
Tracking servo off
Tracking servo on
S-curve measuring mode
All servo off
Top turnback display
Botton turnback display
Center display
Optimum point display
Optimum jitter display
TE traverse display
VC, FE and RF display
Autogain display
(Focus, tracking and sled)
* For button numbers 3, 8, 11, and 12, use them only when an oscilloscope is connected.
4-3.
CLV-S MODE
The spindle servo can be operated for play in the CLV-S mode by connecting TP (ADJ) and TP (GND) after turning on the power supply.
[SERVO BOARD] – Conductor side –
TP
(GND)
IC101
TP 1
(ADJ)
CN101 CN102
TP 2
(AFJ)
– 21 –
SECTION 5
ELECTRICAL ADJUSTMENTS
RF signal waveform
Notes:
1. CD block basically constructed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise indicated.
3. Use the oscilloscope with more than 10 M
Ω
impedance.
4. Clean an object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
S-Curve Check
Connection:
oscilloscope
SERVO board
TP (FE)
TP (VC)
+
–
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
(with the 10: 1 probe in use) level: 1.2
+0.25
–0.20
Vp-p
When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.
Procedure:
1. Connect the oscilloscope to TP (FE) and TP (VC) on SERVO board.
2. Connect the TP (FEI: IC101 pin @ª) and TP (VC) with lead wire.
3. Turned power switch on.
4. Put disc (YEDS-18) in and turned power switch on again and actuate the focus search. (actuate the focus search when disc table is moving in and out.)
5. Confirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within
3.0 ± 1.0 Vp-p.
S-curve waveform symmetry
E-F Balance (Traverse) Check
Connection:
oscilloscope
(DC range)
SERVO board
TP (TE)
TP (VC)
+
–
Procedure:
1. Connect the TP1 (ADJ) to ground and TP (TEI: IC101 pin @¶) to TP (VC) with lead wire.
2. Connect the oscilloscope to TP (TE) and TP (VC) on SERVO board.
3. Turned power switch on.
4. Put disc (YEDS-18) in and press the
( button.
5. Confirm that the oscilloscope waveform is symmetrical on the top and bottom in relation to 0 Vdc, and check this level.
A
Traverse waveform within 3.0 ± 1.0 Vp-p
B
A
B
6. After check, remove the lead wire connected in step 2.
Note:
•
Try to measure several times to make sure that the ratio of A : B or B : A is more than 10 : 7.
•
Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check
Connection:
oscilloscope
(AC range)
SERVO board
TP (RF)
TP (VC)
+
–
6. After check, remove the lead wire connected in step 1.
RF PLL Free-run Frequency Check
Connection:
SERVO board
TP (PLK)
+
– level: 200 ± 100 mVp-p frequency counter
Procedure:
1. Connect the oscilloscope to TP (RF) and TP (VC) on SERVO board.
2. Turned power switch on. (stop mode)
3. Put disc (YEDS-18) in and press the
( button.
4. Confirm that the oscilloscope waveform is clear and check RF signal level is correct or not.
Note: Clear RF signal waveform means that the shape “≈” can be clearly distinguished at the center of the waveform.
Procedure:
1. Connect the frquency counter to TP (PLK).
2. Turned power switch on.
3. Put disc (YEDS-18) in and press the
( button.
4. Confirm that the reading on frequency counter is 4.3218 MHz.
– 22 –
Skew Adjustment
Note : Do not perform the skew adjustment when not using attached stabilizer to a set.
oscilloscope
(AC range)
SERVO board
TP (RF)
TP (VC)
+
–
[SERVO BOARD] – Conductor side –
TP (FE)
TP (RF)
TP (TEI)
29
(FEI)
TP (RFI)
IC101
TP (TE)
TP (VC)
TP
(PLK)
CN101 CN102
TP1 (ADJ)
TP2 (AFJ)
RF signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
(with the 10: 1 probe in use) level: 1.2
+0.25
–0.20
Vp-p
SECTION 6
DIAGRAMS
• Circuit Boards Location
FUSE board
BSL board
SERVO board
LOADING MOTOR board
SW board
POWER board
COAX board
OPT board
LINE board
VR board
KEY-R board
DISPLAY board
LOADING SW board
FL RELAY board
AUDIO board
KEY-L board
FLEX RELAY board adjustment screw
‘ screwdriver
1. Remove the bottom plate, put one third of the unit out from the desk.
2. Connect the osiclloscope to TP (RF) and TP (VC) on SERVO board.
3. Turned power switch on.
4. Put disc (YEDS-18) in and press the
( button.
5. Adjust to be clear the waveform of the oscilloscope turning the adjsutment screw with a ‘ screwdriver.
Note: Clear RF signal waveform means that the shap “≈”can be clearly distinguished at the center of the waveform.
6. After the adjustment, lock the adjustment screw.
– 23 – – 24 –
•
IC Block Diagrams
– SERVO Section –
IC91 M51957AL
–
+
1 2 3 4 5
IC101 CXD2545Q
10
11
8
9
6
7
4
5
1
2
3
SRON
SRDR
SFON
TFDR
TRON
TRDR
TFON
FFDR
FRON
FRDR
FFON
VCO0
VCO1
12
13
TEST
DVSS
TES2
TES3
14
15
16
17
PDO 18
VPCO
VCKI
19
20
100
SLED PWM
GENERATOR
TRACKING PWM
GENERATOR
FOCUS PWM
GENERATOR
PWM GENERATOR
MIRR
DFCT
FOK DETECTOR
SLED
SERVO
TRACKING
SERVO
FOCUS
SERVO
SERVO DSP
99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77
SUBCODE
Q
PROCESSOR
SERVO
AUTO
SEQUENCER
SERVO
MICRO PROGRAM
INTERFACE
CLV
PROCESSOR
NOISE
SHAPER
18-TIMES
OVER SAMPLING
FILTER
32K RAM
D/A
DIGITAL
PROCESSOR
RESISTER PEAK
DETECTOR
3
AVDD
IGEN
AVSS
21
22
23
ADIO 24
RFC 25
A/D
CONVERTER
SWITCH
&
BUFFER
26 27 28 29 30
4
DIGITAL
PLL
VARI-PITCH
DOUBLE SPEED
31 32 33 34 35 36 37 38
MUX
39 40 41 42
76
SUBCODE
P-W
PROCESSOR
TIMING
GENERATOR 1
SYNC
PROTECTOR
DIGITAL
OUT
CLOCK
GENERATOR
SERIAL
PARALLEL
PROCESSOR
43 44 45 46 — 50
75 SBSO
74 SCOR
73 WFCK
72 EMPH
71 D OUT
70
MD2
69
68
67
C16M
C4M
FSTO
66
65
FSTI
DVSS
64
63
62
XTSL
XTAO
XTAI
61
|
51
DA01
|
DA11
– 49 –
IC203 LB1641
T.S.D
MOTOR
DRIVE
O.C.P
MOTOR
DRIVE
1 2 3 4
FWD/REV/STOP
CONTROL LOGIC
5 6 7 8 9 10
– 50 –
– AUDIO Section –
IC350 BA6208
1 2 3
SWITCH
SWITCH
4 5
MOTOR
DRIVE
MOTOR
DRIVE
REG
6 7 8 9
IC404, 504 CXA8042AS
I01+
I02–
NC
I01–
I02+
NC
VCC2
C2
C1
8
9
6
7
3
4
1
2
5
VCC1 10
VREF 11
REFERENCE
VOLTAGE
CIRCUIT
SWITCHING
CIRCUIT
CONSTANT
CURRENT
CIRCUIT
23
22
21
20
19
28
27
26
25
24
IN2–
IN2+
NC
IN1+
IN1–
NC
C4
C3
GND2
VEE2
18
17
VEE1
C6
VCNT
GND1
RIREF
12
13
14
CONTROL
CIRCUIT
16
15
C5
CIREF
IC601 CXD8679Q
IF SELD 52
IF SELC 53
NC 54
SBCKI 55
4BIT DATA
SDATAR 56
SDATAL 57
BITSTREAM
NC 58
DFDTOL 59
DFBCKO 60
DFDTEN 61
TEST1 62
TEST2 63
VSS 64
51 50 49 48 47 46 45 44
S / P
43 42 41 40
TIMING
CIRCUIT
39 38 37 36
OR
ATT
IIR
FIR 4
FIR 1 FIR 2
MODE
FIR 3
OVERFLOW DETECTOR
P/S CONVERT
&
D/F-CLK GEN.
ATT
IIR
FIR 4
FIR 1 FIR 2 FIR 3
OVERFLOW DETECTOR
ATT x 0.75
ATT x 0.75
POLALITY
L . I . P.
DITHER
L . I . P.
35
"0" DETECT
MUTE
CIRCUIT
CLOCK
GENERATOR
34
3rd order
NOISE
SHAPER
3rd order
NOISE
SHAPER
33
DATA SELECT
1 2 3 4 5 6 7 8
DATA SELECT
9
2
10 11 12 13 14 15 16 17 18 19
32 INAF
31 OVFLAG
30 MUTER
29 MUTEL
28 MTPOL
27 DRPOL
26 MODE
25 NC
24 DFDTOR
23 DFLRCKO
22 TEST4
21 TEST3
20 VSS
IC603
IC610
CXD2562Q-CS
DATAOUT
ON/OFF
TEST1
TEST2
52
53
54
TEST3
DVDDL
55
56
VSUB (D) L
VSUB (CHIP) L
VDD2
VDD
L1 (–)
VSS
L1 (+)
VSS2
61
62
63
64
57
58
59
60
51 50 49 48 47 46 45 44 43
42 41 40 39 38 37 36 35 34 33
TIMING CIRCUIT
INTERPOLATER
INTERPOLATER
THIRD ORDER
NOISE SHAPER
THIRD ORDER
NOISE SHAPER
PLM
PLM
S/P
CLOCK
GENERATOR
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
32 SYNC
31 COEF
SPLM
30
29
28
18/20
DVDDR
23
22
21
20
27
26
25
24
VSUB (D) R
VSUB (CHIP) R
VDD2
VDD
R1 (–)
VSS
R1 (+)
VSS2
TC7W74F
8 7 6 5
S R Q
C D Q
1 2 3 4
– PANEL Section –
IC801-803 LC7570E
48 47 46 45 44 43 42 41 40 39 38 37
NC
BLK
VSS
10
11
12
8
9
6
7
4
5
SIN
S33
S32
S31
S30
S29
S28
S27
S26
1
2
3
SHIFT REGISTER
A/D CONVERTER
LATCH, FL DRIVER
13 14 15 16 17 18 19 20 21 22 23 24
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
32
31
30
29
28
27
26
25
36
35
34
33
– 51 – – 52 –
• Waveforms
– SERVO Section –
1
IC101
@§
(RFDC) 200 mV/DIV, 500 ns/DIV
6
IC101
$¶
(BLCK)
2
IC101
@¶
(TE) 200 mV/DIV, 100 µs/DIV
4
IC101
#§
(RFAC) 200 mV/DIV, 500 ns/DIV
5
IC101
$∞
(LRCK)
Approx. 400 mVp-p
5.2 Vp-p
7
474 ns
IC101
^™
(XTAI)
8 ns
9
IC201
#¡
(XTALI)
4 MHz
5.2 Vp-p
5.2 Vp-p
4.8 Vp-p
– AUDIO Section –
1
IC602
1
16.9344 MHz
2
IC602
6
3
IC101
@ª
(FE) 200 mV/DIV, 50 ns/DIV
Approx. 200 mVp-p
16.9344 MHz
8
IC101
(§
(MDP)
2.8 Vp-p
180 ns
3
IC603
0
(XIN)
4
IC604
3
22 ns
45.159 MHz
5
IC610
1
(CK)
1.8 Vp-p
4.8 Vp-p
4.8 Vp-p
840 mVp-p
4 Vp-p
Pin No. Pin Name
SE
FE
VC
FILO
FILI
PCO
CLTV
AVS1
RFAC
BIAS
ASYI
ASYO
AVD1
DVDD
ASYE
PSSL
TES2
TES3
PDO
VPCO
VCKI
AVD2
IGEN
AVS2
ADII
ADIO
RFDC
TE
SRON
SRDR
SFON
TFDR
TRON
TRDR
TFON
FFDR
FRON
FRDR
FFON
VCOO
VCOI
TEST
DVSS
10
11
12
13
14
15
7
8
9
5
6
3
4
1
2
33
34
35
36
28
29
30
31
32
37
38
39
40
41
42
43
20
21
22
16
17
18
19
23
24
25
26
27
I / O
O
I
O
I
—
I
I
I
I
O
—
—
I
I
I
I
O
I
—
I
I
I
O
I
I
—
I
O
O
O
O
O
O
O
O
O
O
O
O
O
I
I
—
6-9.
IC PIN FUNCTION DESCRIPTION
SERVO BOARD IC101 CXD2545Q
(DIGITAL SIGNAL PROCESSOR, FOCUS/TRACKING/SLED SERVO, EFM COMPARATOR)
Function
Sled servo drive PWM signal output terminal Not used (open)
Sled servo drive PWM signal (–) output to the BA6297AFP (IC102)
Sled servo drive PWM signal output terminal Not used (open)
Tracking servo drive PWM signal (–) output to the BA6297AFP (IC102)
Tracking servo drive PWM signal output terminal Not used (open)
Tracking servo drive PWM signal (+) output to the BA6297AFP (IC102)
Tracking servo drive PWM signal output terminal Not used (open)
Focus servo drive PWM signal (+) output to the BA6297AFP (IC102)
Focus servo drive PWM signal output terminal Not used (open)
Focus servo drive PWM signal (–) output to the BA6297AFP (IC102)
Focus servo drive PWM signal output terminal Not used (open)
Oscillator circuit output terminal for analog PLL of the playback EFM Not used (open)
Oscillator circuit input terminal for analog PLL of the playback EFM Not used (fixed at “L”)
Input terminal for the test (fixed at “L”)
Ground terminal (digital system)
Input terminal for the test (fixed at “L”)
Input terminal for the test (fixed at “L”)
Charge-pump output terminal for analog PLL of the playback EFM Not used (open)
PLL charge-pump output terminal for the variable pitch Not used (open)
Clock signal input from external VCO for the variable pitch Not used (fixed at “L”)
Power supply terminal (+5V) (analog system)
Power supply terminal (+5V) (for operational amplifier)
Ground terminal (analog system)
Input terminal for the A/D converter Not used (open)
Output terminal of the operational amplifier Not used (open)
RF signal (DC level) input terminal for the digital servo process
Tracking error signal input from the RF amplifier in optical pick-up
Sled error signal input from the RF amplifier in optical pick-up
Focus error signal input from the RF amplifier in optical pick-up
Middle point voltage (+2.5V) input from the RF amplifier in optical pick-up
Filter output terminal for master clock of the playback master PLL
Filter input terminal for master clock of the playback master PLL
Phase comparison output terminal for master clock of the playback EFM master PLL
Internal VCO control voltage input of the playback master PLL
Ground terminal (analog system)
RF signal (AC level) input terminal for the EFM demodulator
Constant current input terminal of the playback EFM asymmetry circuit
Playback EFM asymmetry comparator voltage input terminal
Playback EFM full-swing output terminal
Power supply terminal (+5V) (analog system)
Power supply terminal (+5V) (digital system)
Playback EFM asymmetry circuit on/off selection input terminal (fixed at “H”)
Audio data output mode selection input terminal (fixed at “L”)
22.7
µ s
44 ns
– 53 – – 54 –
Pin No. Pin Name
44
45
WDCK
LRCK
46 DATA
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
66
67
68
69
62
63
64
65
70
71
72
73
74
BCLK
64 DATA
64 BCLK
64 LRCK
GTOP
XUGF
XPLCK
GFS
RFCK
C2PO
XRAOF
MNT3
MNT2
MNT1
MNT0
XTAI
XTAO
XTSL
DVSS
FSTI
FSTO
C4M
C16M
MD2
DOUT
EMPH
WFCK
SCOR
O
I
O
O
O
I
O
I
—
I
O
O
O
O
O
O
I / O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Function
Word clock signal (88.2 kHz) output terminal Not used (open)
L/R sampling clock signal (44.1 kHz) output to the CXD8679Q (IC601)
DA16 output when PSSL=“H”, 48-bit slot serial data output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Serial data output to the CXD8679Q (IC601)
DA15 output when PSSL=“H”, 48-bit slot bit clock signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Bit clock signal (2.8224 MHz) output to the CXD8679Q (IC601)
DA14 output when PSSL=“H”, 64-bit slot serial data output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA13 output when PSSL=“H”, 64-bit slot bit clock signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA12 output when PSSL=“H”, 64-bit slot L/R sampling clock signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA11 output when PSSL=“H”, GTOP signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA10 output when PSSL=“H”, XUGF signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA09 output when PSSL=“H”, XPLCK signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA08 output when PSSL=“H”, GFS (guard frame sync) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA07 output when PSSL=“H”, RFCK (read frame clock) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA06 output when PSSL=“H”, C2PO signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA05 output when PSSL=“H”, XRAOF (RAM over flow) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA04 output when PSSL=“H”, MNT3 (monitor 3) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA03 output when PSSL=“H”, MNT2 (monitor 2) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA02 output when PSSL=“H”, MNT1 (monitor 1) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
DA01 output when PSSL=“H”, MNT0 (monitor 0) signal output when PSSL=“L”
(PSSL (pin $£)=fixed at “L”) Not used (open)
System clock input terminal (16 MHz)
System clock output terminal (16 MHz) Not used (open)
System clock selection input terminal (fixed at “L”)
Ground terminal (digital system)
2/3 divider input terminal of pins ^™ (XATI) and ^£ (XTAO)
2/3 divider output terminal of pins ^™ (XATI) and ^£ (XTAO)
4.2336 MHz clock signal output terminal Not used (open)
16.9344 MHz clock signal output terminal Not used (open)
Digital out on/off control signal input from the system controller (IC201)
Digital signal (for coaxial out and optical out) output terminal
Emphasis control signal output terminal Not used (open)
Write frame clock signal output terminal Not used (open)
Sub-code sync (S0+S1) detection signal output to the system controller (IC201)
– 55 –
81
96
97
98
90
91
92
93
94
95
86
87
88
89
82
83
84
85
Pin No. Pin Name
75
76
77
78
79
80
SBSO
EXCK
SUBQ
SQCK
MUTE
SENS
XRST
DVDD
MIRR
DFCT
FOK
FSW
MON
MDP
MDS
LOCK
DIRC
SCLK
DFSW
ATSK
DATA
XLAT
CLOK
COUT
99
100
SSTP
SFDR
I
O
O
O
O
O
—
O
O
O
I
O
I
I
I
I
I
I
I / O
O
I
O
I
I
O
I
O
Function
Sub-code P-W serial data output terminal Not used (open)
Sub-code P-W serial data reading clock signal input terminal Not used (fixed at “L”)
Sub-code Q data signal output to the system controller (IC201)
Sub-code Q data reading clock signal input from the system controller (IC201)
Mute signal input from the system controller (IC201)
Internal status (SENSE) signal output to the system controller (IC201)
System reset signal input from the reset signal generator (IC91) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
1-track jump mode input terminal Not used (fixed at “H”)
Sense serial data reading clock signal input from the system controller (IC201)
Defect on/off select signal input terminal Not used (fixed at “L”)
Input terminal for the anti-shock Not used (fixed at “L”)
Serial data input from the system controller (IC201)
Serial data latch pulse signal input from the system controller (IC201)
Serial data transfer clock signal input from the system controller (IC201)
Track number count signal output terminal Not used (open)
Power supply terminal (+5V) (digital system)
Mirror detection signal output terminal Not used (open)
Defect signal output terminal Not used (open)
Focus OK signal output terminal Not used (open)
Selection signal output terminal of the output filter for spindle motor Not used (open)
Spindle motor on/off control signal output terminal Not used (open)
Spindle servo control signal output terminal
Spindle servo control signal output terminal Not used (open)
GFS is sampled by 460 Hz “H” output when GFS is “H” Not used (open)
Detection input from the sled limit-in detect switch (S22)
The optical pick-up is inner position when “H”
Sled servo drive PWM signal (+) output to the BA6297AFP (IC102)
– 56 –
SERVO BOARD IC201 CXP84124-068Q (SYSTEM CONTROLLER)
Pin No.
Pin Name I / O Function
26
27
28
13
14
15
10
11
12
7
8
5
6
9
3
4
1
2
22
23
24
19
20
21
16
17
18
25
29
30
35
36
37
38
31
32
33
34
39
40
A7
A8
A9
A10
A11
A3
A4
A5
A6
A12
WE
NC
NC
LED-PLAY
LED-PAUSE
LED-FILTER
SPDL-MUTE
SHIFT-ON/OFF
VOL UP
VOL DOWN
BLANK
FL D0
FL D1
FL D2
FL CLK
FL WR
SENSER SW
SENSER
LIMIT OUT
RESET
XTALI
XTALO
VSS
TX
TEX
AVSS
AVREF
K0
K1
K2
O
O
I
I
I
I
—
I
O
—
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
I
I
I
I
Address signal output to the static RAM (IC202)
Write enable signal output to the static RAM (IC202)
Not used (open)
Not used (open)
( LED (D871) drive signal output terminal “H”: LED on
P LED (D872) drive signal output terminal “H”: LED on
FILTER LED (D873) drive signal output terminal “H”: LED on
Mute signal output to the spindle motor driver (IC104, 105)
Reset signal output to the CXD2562Q-CS (IC603) “L”: reset
Volume up control signal output to the volume control motor driver (IC350)
Volume down control signal output to the volume control motor driver (IC350)
Blank signal output to the fluorescent indicator tube driver (IC801 to IC803)
Serial data output to the fluorescent indicator tube driver (IC803)
Serial data output to the fluorescent indicator tube driver (IC802)
Serial data output to the fluorescent indicator tube driver (IC801)
Serial data transfer clock signal output to the fluorescent indicator tube driver (IC801 to
IC803)
Read/write select signal output to the fluorescent indicator tube driver (IC801 to IC803)
On/off control signal output to the stabilizer detect sensor (IC261) “H”: on
Detect signal input from the stabilizer detect sensor (IC261) “H”: on
Detection input from the sled limit-out detect switch (S21)
The optical pick-up is outer position when “L”
System reset signal input from the reset signal generator (IC91) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
Main system clock input terminal (4 MHz)
Main system clock output terminal (4 MHz)
Ground terminal
Sub system clock output terminal Not used (open)
Sub system clock input terminal Not used (fixed at “L”)
Ground terminal (for A/D converter)
Reference voltage input terminal (+5V)
Key input terminal (A/D input) ERASE key (S850) input
Key input terminal (A/D input)
FILE, EDIT/TIME FADE, TIME, REPEAT, P MODE keys (S851 to S855) input
Key input terminal (A/D input)
CHECK, CLEAR, FILTER,
0, ) , PUSH ENTER keys (S884 to S888, RV870) input
– 57 –
Pin No.
Pin Name I / O
41
70
71
72
73
74
75
76
66
67
68
69
77
78
79
80
62
63
64
65
58
59
60
61
54
55
56
57
50
51
52
53
46
47
48
49
42
43
44
45
*1 Loading motor (M271) control
Operation
Terminal
LOAD OUT (pin ^¢)
LOAD IN (pin ^∞)
OFF
“L”
“L”
K3
TEST
TEST
SCOR
AMUTE
LDON
XLT
LOAD OUT
LOAD IN
DOUT
DMUTE
D0
D1
D2
D3
VDD
NC
D4
D5
D6
D7
A0
A1
A2
K4
K5
ADJ/AFJ
IN/OUT SW
SCLK
PRGL
CLK
SENSE
DATA
SQCK
SUBQ
TEST
SEL1
SEL0
RMIN
TIMER
I
I/O
I/O
—
I
O
O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
O
O
I
O
I
I
I
I
O
O
I
O
O
O
O
I
I
I
I
I
Function
Key input terminal (A/D input)
§ OPEN/CLOSE, (, P, p keys (S889 to S892) input
Rotary encoder input terminal (A/D input) AMS
± key (RV870) input
Rotary encoder input terminal (A/D input) AMS
≠ key (RV870) input
Setting terminal for the test mode “L” active
Detection input from the loading in/out detect switch (S281, S282) (A/D input)
Sense serial data reading clock signal output to the CXD2545Q (IC101)
Serial data latch pulse signal output to the CXD8679Q (IC601)
Serial data transfer clock signal output to the CXD2545Q (IC101) and CXD8679Q (IC601)
Internal status (SENSE) signal input from the CXD2545Q (IC101)
Serial data output to the CXD2545Q (IC101) and CXD8679Q (IC601)
Sub-code Q data reading clock signal output to the CXD2545Q (IC101)
Sub-code Q data signal input from the CXD2545Q (IC101)
Output terminal for the test Not used (open)
Destination setting terminal (fixed at “L”)
Destination setting terminal (fixed at “L”)
Remote control signal input from the remote control receiver (IC804)
Timer control input terminal Not used (fixed at “H”)
Output terminal for the test Not used (open)
Output terminal for the test Not used (open)
Sub-code sync (S0+S1) detection signal input from the CXD2545Q (IC101)
Muting control signal output to the analog mute driver and mute relay driver
Laser diode on/off selection signal output to the RF amplifier in optical pick-up
Serial data latch pulse signal output to the CXD2545Q (IC101)
Loading motor (M271) drive signal output to the LB1641 (IC203) *1
Loading motor (M271) drive signal output to the LB1641 (IC203) *1
Digital out on/off control signal output to the CXD2545Q (IC101)
Muting control signal output to the CXD2545Q (IC101) and CXD8679Q (IC601)
Two-way data bus with the static RAM (IC202)
Power supply terminal (+5V)
Not used (fixed at “H”)
Two-way data bus with the static RAM (IC202)
Address signal output to the static RAM (IC202)
OUT
“H”
“L”
I N
“L”
“H”
BRAKE
“H”
“H”
– 58 –
Main Ports
SPDL-MUTE (pin !¶)
From the viewpoint of performance of the set, the disc must not move nor sway when the disc table opens. These problems however occur in the actual case due to the offset voltage generated and the voltage generated because of the positional relation between the BSL coil and Hall element.
The spindle motor driver (IC104, IC105) is therefore muted while the tray is open. Pin !¶ provides the timing for this.
H
SP MUTE
L
(MUTE ON)
OPEN
Reverses after a certain period of time.
PLAY
CLOSE
Reverses after a certain period of time.
SPINDLE
KICK
Time while the disc can be seen
(Estimate).
The spindle motor driver is muted during this time.
BLANK (pin @¡)
This port is required because the display tube in this set static-lights up and a dedicated screwdriver is required. It is basically a RESET pin. But as problems will occur if used also as RESET, timings are specially provided using the micro-processor.
SENSER SW (pin @¶)
As IC261 IS471F operate in pulse as shown in the figure, the sound quality may be affected if operated constantly. As the purpose of IC261 is to detect if the presence of the stabilizer, it should be operated only when the tray is drawn in. IC261 operates as it is “H” only at this time. Normally it is “L”.
Eep
Ee
Eed
0
GLout pin output waveform
Time
SENSER (pin @•)
The results of the detection of IC261 IS471F is output to this pin. It becomes “ L” when there is no stabilizer (when light reaches). The next process of imposing the next focus is not performed. (Effective only when pin @¶ is “H”.)
Therefore, it must be noted that if PLAY is performed when the servo board at the top of the CDM is not assembled properly, the detection circuit operates and this pin does not operate.
It is does not operate, refer to 1. SERVICING NOTES ” Preparations for Adjustment and Measurement” on page 3.
*
Eep is the luminance of the signal light tuned with the low level timing of the GLout pin output.
Eed is the luminance of the D.C. light. The light source is the infrated-emitting diode (
λ p=940 nm).
– 59 –
SECTION 7
EXPLODED VIEWS
NOTE:
•
-XX and -X mean standardized parts, so they may have some difference from the original one.
•
Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE)
↑
Cabinet's Color
(1) CASE, LOADING PANEL SECTION
•
Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
•
The mechanical parts with no reference number in the exploded views are not supplied.
•
Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list.
8
8
The components identified by mark ! or dotted line with mark ! are critical for safety.
Replace only with part number specified.
12
9
8
11
21
13
not supplied
8
7
FRONT PANEL SECTION
7
23
22
#2
6
7
10
11
14
4
5
not supplied
3
2
19
8
* 5
6
6
4
4
8
9
7
8
9
Ref. No.
2
3
1
1
3
1
7
not supplied
18
15
not supplied
#1 (For gold)
#2 (For black)
16
Part No.
Description
4-970-998-01 BOLT (LID), HEXAGON HOLE (BLACK)
4-970-998-11 BOLT (LID), HEXAGON HOLE (GOLD)
4-969-832-01 PLATE, INDICATION
4-969-830-21 PANEL, LOADING (BLACK)
4-969-830-31 PANEL, LOADING (GOLD)
Remark
4-969-831-21 BASE, LOADING PANEL (BLACK)
4-969-831-31 BASE, LOADING PANEL (GOLD)
1-654-256-11 DISPLAY BOARD
4-951-620-41 SCREW (2.6), +BVTP (BLACK)
4-951-620-51 SCREW (2.6), +BVTP (GOLD)
4-929-074-01 SCREW (3X8)
4-976-827-01 SCREW, FLAT HEAD (BLACK)
4-976-827-11 SCREW, FLAT HEAD (GOLD)
4-969-823-01 PLATE (L), SIDE (BLACK)
4-969-823-11 PLATE (L), SIDE (GOLD)
#3
Ref. No.
10
11
12
12
* 13
14
14
15
16
18
19
19
20
22
23
7
#3
15
16
Part No.
Description
4-972-439-01 SPACER (SCREW HEAD)
4-972-438-01 ABSORBENT, VIBRATION
4-969-821-01 CASE (TOP PLATE) (BLACK)
4-969-821-11 CASE (TOP PLATE) (GOLD)
A-4660-735-A REINFORCEMENT (TOP PLATE) ASSY
Remark
4-969-824-01 PLATE (R), SIDE (BLACK)
4-969-824-11 PLATE (R), SIDE (GOLD)
4-970-123-01 FOOT (F50180S)
4-970-124-01 CUSHION (F50180S)
4-969-834-01 FILTER
4-969-833-21 COVER, LOADING PANEL (BLACK)
4-969-833-31 COVER, LOADING PANEL (GOLD)
4-949-302-31 WASHER
4-972-440-01 SPACER
4-949-302-01 WASHER
– 60 –
(2) FRONT PANEL SECTION
53
spindle with J461 spindle with RV350
54
58
59
58
58
55
56
71
60
58
61
71
62
72
58
58
52
#4
#4
70
69
73
66
65
64
63
67
51
supplied with R870
#4 supplied with 51
68
Ref. No.
51
51
52
52
53
53
54
54
55
55
* 56
* 57
58
* 59
* 60
61
62
* 63
Part No.
Description
4-987-121-01 KNOB (AMS) (GOLD)
4-987-121-11 KNOB (AMS) (BLACK)
4-950-189-01 KNOB (A) (VOL) (BLACK)
4-950-189-41 KNOB (A) (VOL) (GOLD)
4-942-568-01 EMBLEM (NO.5), SONY (BLACK)
4-942-568-31 EMBLEM (NO.5), SONY (GOLD)
4-969-470-21 PANEL (L) (GOLD)
4-969-470-32 PANEL (L) (BLACK)
4-923-520-51 KNOB, POWER (POWER) (BLACK)
4-923-520-61 KNOB, POWER (POWER) (GOLD)
1-663-636-11 SW BOARD
4-969-478-01 BRACKET (HP)
4-951-620-01 SCREW (2.6X8), +BVTP
1-663-635-11 VR BOARD
A-4699-344-A KEY-R BOARD, COMPLETE
4-969-818-01 PACKING
4-969-819-11 RETAINER (PACKING)
A-4699-345-A KEY-L BOARD, COMPLETE
Remark
70
70
71
71
* 72
67
67
68
68
69
73
Ref. No.
* 64
65
65
66
66
Part No.
Description Remark
3-362-478-01 HOLDER (T), LED
4-986-673-01 BUTTON (FF) ( 0. )) (GOLD)
4-986-673-11 BUTTON (FF) ( 0. )) (BLACK)
X-4945-276-1 BUTTON (PLAY) ASSY
( §. OPEN /CLOSE. ”. P. p) (BLACK)
X-4948-030-1 PLAY ASSY, BUTTON
( §. OPEN /CLOSE. ”. P. p) (GOLD)
4-986-665-01 BASE (R), PANEL (GOLD)
4-986-665-11 BASE (R), PANEL (BLACK)
4-986-683-01 PANEL, FRONT (GOLD)
4-986-683-11 PANEL, FRONT (BLACK)
4-971-776-01 INDICATOR
4-969-817-01 PANEL (MD) (BLACK)
4-969-817-11 PANEL (MD) (GOLD)
4-986-672-01 BUTTON (3) (GOLD)
4-986-672-11 BUTTON (3) (BLACK)
4-922-248-11 SPACER
4-949-302-21 WASHER
– 61 –
(3) CHASSIS SECTION
not supplied
108
not supplied
108
T902
104
103
101
#9
#5
#7
T901
#5
#9
104
102
#4
103
not supplied
#20
CDM32BB-12B
CDM32BN-12B
108
#20
108
101
not supplied
#4
#4 not supplied
#4
#4
#4
116
105
not supplied
101
114
115
#6
108
not supplied
110
107
106
108
#6
109
108
#4
113
112
111
101
#4
101
Ref. No.
101
* 102
* 103
104
105
* 106
* 107
108
* 109
! 110
Part No.
Description
4-929-074-01 SCREW (3X8)
1-663-628-11 FUSE BOARD
4-888-798-00 BUSHING, RUBBER
4-928-032-01 COLLAR (A)
2-259-121-01 SCREW, TR
A-4699-569-A AUDIO BOARD, COMPLETE
4-923-873-01 BRACKET, CORD STOPPER
4-974-510-01 SCREW (+BV 3X8 B)
3-703-244-00 BUSHING (2104), CORD
1-558-568-21 CORD, POWER
108
not supplied
101
not supplied
The components identified by mark
! or dotted line with mark
! are critical for safety.
Replace only with part number specified.
Remark Ref. No.
* 111
* 111
* 112
* 113
* 114
* 115
* 116
! T901
! T902
Part No.
Description
4-986-742-11 PANEL, BACK (AEP)
4-986-742-22 PANEL, BACK (Singapore)
1-663-629-11 LINE BOARD
1-663-630-11 OPT BOARD
1-663-631-11 COAX BOARD
Remark
4-913-152-01 ESCUTCHEON, D/O
A-4699-570-A POWER BOARD, COMPLETE
1-427-816-11 TRANSFORMER, POWER (for AUDIO)
1-427-817-11 TRANSFORMER, POWER (for DIGITAL)
– 62 –
(4) MECHANISM SECTION-1
(CDM32BB-12B) (BLACK)
(CDM32BN-12B) (GOLD)
157
#6
#10
156
158
#12
#12 not supplied
151
#12
154
153
155
#16
#14
160
BU-12B
#16
155
#6
159
160
not supplied
#15
161
152
#11
#10
#6
#13
162
163
Ref. No.
* 151
* 152
153
* 154
155
156
157
Part No.
Description
A-4699-587-A SERVO BOARD, COMPLETE
1-653-906-11 FL RELAY BOARD
1-769-109-11 WIRE (FLAT TYPE) (12 CORE)
4-968-903-01 SHAFT (MAIN)
4-927-634-01 HOLDER (SP)
4-968-907-11 PANEL (DRAWER)
4-971-000-21 COVER (CD) (BLACK)
Remark Ref. No.
157
158
* 159
160
* 161
* 162
163
Part No.
Description
4-971-000-31 COVER (CD) (GOLD)
1-769-110-11 WIRE (FLAT TYPE) (26 CORE)
1-654-005-11 FLEX RELAY BOARD
4-948-375-01 SPRING (F), COIL
4-968-906-01 HOLDER, BU
4-968-904-01 SHAFT (SUB)
4-925-315-31 DAMPER
– 63 –
Remark
(5) MECHANISM SECTION-2
(CDM32BB-12B) (BLACK)
(CDM32BN-12B) (GOLD)
209
#10
205
208
207
210
206
211
213
212
214
#10
M271
215
218
216
217
214
#10
#17
#10
#10
214
215
215
202
219
not supplied
203
#12
202
201
Ref. No.
201
202
* 203
* 204
* 205
206
207
* 208
209
210
Part No.
Description
4-968-905-01 BELT (CDM)
X-4945-209-1 PULLEY (FIRST) ASSY
4-972-921-01 COVER (SW)
1-653-905-11 LOADING SW BOARD
4-968-901-01 BEARING (MAIN)
X-4945-207-1 BRACKET (LAST) ASSY
4-968-900-01 GEAR (LAST)
4-970-999-01 ROLLER (J RACK)
4-973-849-01 WASHER
3-363-191-01 WASHER (BA)
Remark Ref. No.
211
212
213
* 214
* 215
Part No.
Description
4-968-899-01 GEAR (MIDLE)
4-968-898-01 GEAR (FIRST)
3-325-697-31 WASHER
4-928-026-01 COLLAR (B)
4-888-798-11 BUSHING, RUBBER
* 216
217
1-653-907-11 LOADING MOTOR BOARD
4-971-894-01 DAMPER (MOTOR)
218
* 219
X-4945-205-1 SHAFT ASSY
4-968-902-01 BEARING (SUB)
M271 X-4945-565-1 MOTOR ASSY (LOADING)
– 64 –
Remark
(6) BASE UNIT SECTION
(BU-12B)
257
258
256
259
not supplied
260
255
254
253
252
274
261
270
262
263
#6
266
#19
#18
270
265
264
267
268
#20
#6
269
263
270
271
not supplied #1
272
S21, S22
M21
273
251
Ref. No.
251
* 252
253
254
255
256
257
258
259
260
261
262
263
264
Part No.
Description
A-4660-688-A STABILIZER ASSY
A-4699-545-A BSL BOARD, COMPLETE
X-4945-273-1 ROTOR ASSY
3-701-444-11 WASHER, 6
X-4945-203-1 BASE ASSY, SLIDE
Remark
A-4660-814-A PULLEY ASSY, DISK
4-968-871-01 WASHER (SPINDLE)
4-968-867-01 CAP, CENTERING
4-968-869-01 SPRING (CENTERING), COMPRESSION
4-968-870-01 RACK, SLIDE
4-968-880-01 SPRING (SLED), COMPRESSION
4-968-866-01 GEAR (D)
4-917-562-21 INSULATOR
4-968-916-01 BRACKET (OP BASE)
270
271
* 272
273
274
M21
S21
S22
Ref. No.
265
! 266
* 267
268
269
#6
The components identified by mark
! or dotted line with mark
! are critical for safety.
Replace only with part number specified.
Remark Part No.
Description
4-970-924-01 SPRING (SKEW), LEAF
8-820-014-01 OPTICAL PICK-UP KSS-273B/J1N
4-968-944-01 SHAFT, SLED
4-968-865-01 GEAR (C)
4-968-879-01 SPRING (OP), LEAF
3-364-731-01 WASHER, POLY-SLIDER
4-968-864-01 GEAR (B)
4-968-862-01 BASE, MECHANICAL
1-653-918-11 FLEXIBLE BOARD
4-971-266-01 SCREW (M2.6X4)
X-4945-920-1 MOTOR ASSY (SLED)
1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT OUT)
1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT IN)
– 65 –
AUDIO
NOTE:
•
Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.
•
-XX and -X mean standardized parts, so they may have some difference from the original one.
•
RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
SECTION 8
ELECTRICAL PARTS LIST
•
Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
•
SEMICONDUCTORS
In each case, u: µ, for example: uA. .
: µA. .
uPA. . : µPA. .
uPB. .
: µPB. .
uPC. . : µPC. .
uPD. .
: µPD. .
•
CAPACITORS uF: µF
•
COILS uH: µH
The components identified by mark
! or dotted line with mark
! are critical for safety.
Replace only with part number specified.
When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
C433
C434
C435
C436
C437
C441
C451
C452
C453
C501
C502
C503
C504
C505
C513
C420
C421
C422
C423
C424
C425
C428
C429
C431
C432
C401
C402
C403
C404
C405
C413
C414
C417
C418
C419
* A-4699-569-A AUDIO BOARD, COMPLETE
**********************
< BUS BAR >
BB601 1-566-940-21 BUS BAR 3P
< CAPACITOR >
1-136-850-11 FILM
1-124-910-11 ELECT
1-136-850-11 FILM
1-124-910-11 ELECT
1-136-850-11 FILM
0.1uF
47uF
0.1uF
47uF
0.1uF
1-136-810-11 FILM
1-136-810-11 FILM
1-136-817-91 FILM
1-136-814-11 FILM
1-104-646-11 CERAMIC
5% 63V
20% 50V
5% 63V
20% 50V
5% 63V
220PF
220PF
5% 100V
5% 100V
0.0033uF 5% 100V
0.001uF
5% 100V
2.2uF
20% 50V
1-117-775-31 FILM
1-128-197-11 ELECT
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-130-973-00 FILM
1-130-969-11 FILM
0.1uF
10uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10% 250V
20% 63V
5% 63V
5% 63V
5% 63V
5% 63V
5% 63V
5% 63V
0.022uF
3% 100V
0.012uF
3% 100V
1-130-969-11 FILM
1-136-233-11 FILM
1-136-233-11 FILM
1-128-200-11 ELECT
1-128-200-11 ELECT
1-164-159-11 CERAMIC
1-162-199-31 CERAMIC
1-126-024-11 ELECT
1-162-199-31 CERAMIC
1-136-850-11 FILM
1-124-910-11 ELECT
1-136-850-11 FILM
1-124-910-11 ELECT
1-136-850-11 FILM
1-136-810-11 FILM
0.012uF
3% 100V
0.0047uF 3% 100V
0.0047uF 3% 100V
47uF 20% 63V
47uF
0.1uF
10PF
220uF
10PF
0.1uF
47uF
0.1uF
47uF
0.1uF
220PF
20% 63V
5%
20%
5%
5%
50V
50V
25V
50V
63V
20% 50V
5% 63V
20% 50V
5% 63V
5% 100V
Remark
C607
C608
C609
C610
C611
C612
C613
C614
C615
C621
C622
C623
C624
C625
C541
C551
C552
C553
C601
C602
C603
C604
C605
C606
C528
C529
C530
C531
C532
C533
C534
C535
C536
C537
Ref. No.
C514
C517
C518
C519
C520
C521
C522
C523
C524
C525
Part No.
Description
1-136-810-11 FILM
1-136-817-91 FILM
1-136-814-11 FILM
1-104-646-11 CERAMIC
1-117-775-31 FILM
1-128-197-11 ELECT
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-136-850-11 FILM
1-130-973-00 FILM
1-130-969-11 FILM
1-130-969-11 FILM
1-136-233-11 FILM
1-136-233-11 FILM
1-128-200-11 ELECT
1-128-200-11 ELECT
1-164-159-11 CERAMIC
1-162-199-31 CERAMIC
1-126-024-11 ELECT
1-162-199-31 CERAMIC
1-126-023-11 ELECT
1-164-732-11 CERAMIC
1-164-159-11 CERAMIC
1-164-732-11 CERAMIC
1-164-159-11 CERAMIC
1-164-732-11 CERAMIC
1-162-290-31 CERAMIC
1-128-200-11 ELECT
1-117-775-31 FILM
1-164-732-11 CERAMIC
1-102-947-00 CERAMIC
1-102-947-00 CERAMIC
1-128-201-11 ELECT
1-162-290-31 CERAMIC
1-164-732-11 CERAMIC
1-117-855-51 ELECT
1-117-855-51 ELECT
1-126-023-11 ELECT
1-126-023-11 ELECT
1-128-201-11 ELECT
Remark
220PF 5% 100V
0.0033uF 5% 100V
0.001uF
5% 100V
2.2uF
20% 50V
0.1uF
10% 250V
10uF
0.1uF
0.1uF
0.1uF
0.1uF
20% 63V
5% 63V
5% 63V
5% 63V
5% 63V
470PF
47uF
0.1uF
0.1uF
10PF
10PF
100uF
470PF
0.1uF
10uF
10uF
100uF
100uF
100uF
0.1uF
10PF
220uF
10PF
100uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
5% 63V
5% 63V
0.1uF
5% 63V
0.022uF
3% 100V
0.012uF
3% 100V
0.012uF
3% 100V
0.0047uF 3% 100V
0.0047uF 3% 100V
47uF 20% 63V
47uF 20% 63V
5%
20%
5%
20%
20%
50V
50V
25V
50V
25V
20% 50V
50V
20% 50V
50V
50V
10% 50V
20% 63V
10% 250V
20% 50V
5% 50V
5% 50V
20% 63V
10% 50V
20% 50V
20% 50V
20% 50V
20% 25V
20% 25V
20% 63V
– 66 –
AUDIO
Ref. No.
C626
C627
C628
C650
C651
Part No.
Description
1-128-201-11 ELECT 100uF
Remark
20% 63V
1-128-201-11 ELECT
1-128-201-11 ELECT
1-162-294-31 CERAMIC
1-164-159-11 CERAMIC
< CONNECTOR >
100uF
100uF
20% 63V
20% 63V
0.001uF
10% 50V
0.1uF
50V
CN401 1-764-325-11 PIN, CONNECTOR (PCB) (V TYPE) 2P
CN402 1-764-325-11 PIN, CONNECTOR (PCB) (V TYPE) 2P
CN501 1-764-325-11 PIN, CONNECTOR (PCB) (V TYPE) 2P
CN502 1-764-325-11 PIN, CONNECTOR (PCB) (V TYPE) 2P
* CN601 1-691-462-11 PIN, CONNECTOR (PC BOARD) 6P
CN602 1-691-463-31 PIN, CONNECTOR (PC BOARD) 7P
CN608 1-764-326-11 PIN, CONNECTOR (PCB) (V TYPE) 3P
CN609 1-764-327-11 PIN, CONNECTOR (PCB) (V TYPE) 4P
CN610 1-764-327-11 PIN, CONNECTOR (PCB) (V TYPE) 4P
CN611 1-691-459-21 PIN, CONNECTOR (PC BOARD) 3P
D401
D441
D501
D541
D602
D603
D625
D626
< DIODE >
8-719-987-63 DIODE 1N4148M
8-719-987-63 DIODE 1N4148M
8-719-987-63 DIODE 1N4148M
8-719-987-63 DIODE 1N4148M
8-719-115-65 DIODE RD6.8JS-T2B1
8-719-987-63 DIODE 1N4148M
8-719-210-21 DIODE 11EQS04
8-719-210-21 DIODE 11EQS04
< MOUNT/GROUND TERMINAL >
ET602 4-924-264-01 TERMINAL, MOUNT
ET650 1-537-770-21 TERMINAL BOARD, GROUND
ET651 1-537-770-21 TERMINAL BOARD, GROUND
< IC >
IC401 8-759-259-12 IC OPA2604AP
IC402 8-759-443-33 IC OPA2132PA
IC403 8-759-053-07 IC OP-27GP
IC404 8-759-371-51 IC CXA8042AS
IC501 8-759-259-12 IC OPA2604AP
IC502 8-759-443-33 IC OPA2132PA
IC503 8-759-053-07 IC OP-27GP
IC504 8-759-371-51 IC CXA8042AS
IC601 8-759-462-70 IC CXD8679Q
IC602 8-759-242-70 IC TC7WU04F
IC603 8-759-454-42 IC CXD2562Q-CS
IC604 8-759-242-70 IC TC7WU04F
IC605 8-759-231-53 IC TA7805S
IC606 8-759-981-85 IC RC4556D
IC607 8-759-604-86 IC M5F7807L
IC608 8-759-604-90 IC M5F7907L
IC609 8-759-708-05 IC NJM78L05A
IC610 8-759-180-84 IC TC7W74F
< COIL >
L403
L404
L405
L406
L408
1-414-514-21 INDUCTOR 10uH
1-414-512-21 INDUCTOR 6.8uH
1-412-473-21 INDUCTOR 0uH
1-412-473-21 INDUCTOR 0uH
1-414-510-21 INDUCTOR 3.3uH
Ref. No.
Part No.
Description Remark
L541
L543
L551
L552
L553
L601
L602
L603
L605
L441
L443
L451
L452
L453
L503
L504
L505
L506
L508
Q405
Q441
Q442
Q451
Q505
Q541
Q542
Q551
Q601
Q607
R416
R417
R418
R427
R429
R430
R431
R432
R433
R434
R401
R402
R403
R404
R409
R410
R411
R412
R413
R414
R435
R437
R439
R440
R441
1-414-512-21 INDUCTOR 6.8uH
1-414-512-21 INDUCTOR 6.8uH
1-414-512-21 INDUCTOR 6.8uH
1-414-509-21 INDUCTOR 2.2uH
1-414-512-21 INDUCTOR 6.8uH
1-414-514-21 INDUCTOR 10uH
1-414-512-21 INDUCTOR 6.8uH
1-412-473-21 INDUCTOR 0uH
1-412-473-21 INDUCTOR 0uH
1-414-510-21 INDUCTOR 3.3uH
1-414-512-21 INDUCTOR 6.8uH
1-414-512-21 INDUCTOR 6.8uH
1-414-512-21 INDUCTOR 6.8uH
1-414-509-21 INDUCTOR 2.2uH
1-414-512-21 INDUCTOR 6.8uH
1-414-510-21 INDUCTOR 3.3uH
1-414-510-21 INDUCTOR 3.3uH
1-414-510-21 INDUCTOR 3.3uH
1-414-510-21 INDUCTOR 3.3uH
< TRANSISTOR >
8-729-224-63 FET 2SK246-BL
8-729-900-80 TRANSISTOR DTC114ES
8-729-900-65 TRANSISTOR DTA144ES
8-729-231-55 TRANSISTOR 2SC2878-AB
8-729-224-63 FET 2SK246-BL
8-729-900-80 TRANSISTOR DTC114ES
8-729-900-65 TRANSISTOR DTA144ES
8-729-231-55 TRANSISTOR 2SC2878-AB
8-729-900-65 TRANSISTOR DTA144ES
8-729-900-65 TRANSISTOR DTA144ES
< RESISTOR >
1-249-913-11 CARBON
1-249-913-11 CARBON
1-249-885-11 CARBON
1-249-885-11 CARBON
1-249-946-11 CARBON
1-249-946-11 CARBON
1-249-946-11 CARBON
1-249-946-11 CARBON
1-249-923-11 CARBON
1-249-923-11 CARBON
390
390
27
27
9.1K
9.1K
9.1K
9.1K
1K
1K
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1-249-520-11 CARBON
1-249-959-11 CARBON
1-249-931-11 CARBON
1-249-637-11 CARBON
1-249-979-91 CARBON
1-249-995-11 CARBON
1-249-979-91 CARBON
1-249-977-11 CARBON
1-249-506-11 CARBON
1-249-917-11 CARBON
1-249-504-11 CARBON
1-249-504-11 CARBON
1-249-504-11 CARBON
1-249-504-11 CARBON
1-259-476-11 CARBON
47
33K
2.2K
33
220K
1M
220K
180K
12
560
10
10
10
10
100K
5% 1/4W
1% 1/4W
1% 1/4W
5% 1/2W
1% 1/4W
5% 1/4W
1% 1/4W
1% 1/4W
5% 1/4W
1% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/6W
– 67 –
AUDIO BSL COAX
Part No.
Description
1-259-452-11 CARBON
1-259-472-11 CARBON
1-259-444-11 CARBON
1-259-476-11 CARBON
1-259-456-11 CARBON
1-259-464-11 CARBON
1-259-468-11 CARBON
1-259-396-11 CARBON
1-259-416-11 CARBON
1-259-416-11 CARBON
1-259-416-11 CARBON
1-259-416-11 CARBON
1-249-931-11 CARBON
1-259-440-11 CARBON
1-249-913-11 CARBON
1-249-913-11 CARBON
1-249-885-11 CARBON
1-249-885-11 CARBON
1-249-946-11 CARBON
1-249-946-11 CARBON
1-249-946-11 CARBON
1-249-946-11 CARBON
1-249-923-11 CARBON
1-249-923-11 CARBON
1-249-520-11 CARBON
1-249-959-11 CARBON
1-249-931-11 CARBON
1-249-637-11 CARBON
1-249-979-91 CARBON
1-249-995-11 CARBON
1-249-979-91 CARBON
1-249-977-11 CARBON
1-249-506-11 CARBON
1-249-917-11 CARBON
1-249-504-11 CARBON
1-249-504-11 CARBON
1-249-504-11 CARBON
1-249-504-11 CARBON
1-259-476-11 CARBON
1-259-452-11 CARBON
1-259-472-11 CARBON
1-259-444-11 CARBON
1-259-476-11 CARBON
1-259-456-11 CARBON
1-259-464-11 CARBON
1-259-468-11 CARBON
1-259-396-11 CARBON
1-259-416-11 CARBON
1-259-416-11 CARBON
1-259-416-11 CARBON
1-259-416-11 CARBON
1-249-931-11 CARBON
1-259-440-11 CARBON
R543
R551
R552
R553
R554
R555
R556
R581
R582
R583
R584
R585
R591
R531
R532
R533
R534
R535
R537
R539
R540
R541
R542
R511
R512
R513
R514
R516
R517
R518
R527
R529
R530
Ref. No.
R442
R443
R451
R452
R453
R454
R455
R456
R481
R482
R483
R484
R485
R491
R501
R502
R503
R504
R509
R510
47K
47
330
330
330
68K
4.7K
100K
15K
33K
330
2.2K
3.3K
220K
180K
12
560
10
10
10
10
100K
10K
9.1K
9.1K
1K
1K
47
33K
2.2K
33
220K
1M
330
330
2.2K
3.3K
390
390
27
27
9.1K
9.1K
33K
47K
47
330
330
10K
68K
4.7K
100K
15K
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
1% 1/4W
5% 1/6W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
5% 1/4W
1% 1/4W
1% 1/4W
5% 1/2W
1% 1/4W
5% 1/4W
1% 1/4W
1% 1/4W
5% 1/4W
1% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/6W
5% 1/6W
Remark
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
1% 1/4W
5% 1/6W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
1% 1/4W
R609
R610
R611
R612
R613
R614
R615
R616
! R617
R628
R629
R630
! R631
! R632
Ref. No.
R601
R602
R603
R604
R605
R607
R608
Part No.
Description
1-259-428-11 CARBON
1-259-428-11 CARBON
1-259-428-11 CARBON
1-259-428-11 CARBON
1-259-424-11 CARBON
1-259-424-11 CARBON
1-259-420-11 CARBON
1-259-430-11 CARBON
1-259-420-11 CARBON
1-259-420-11 CARBON
1-249-947-11 CARBON
1-259-416-11 CARBON
1-259-412-11 CARBON
1-259-448-11 CARBON
1-259-420-11 CARBON
1-212-887-00 FUSIBLE
1-259-484-11 CARBON
1-259-460-11 CARBON
1-259-476-11 CARBON
1-219-022-11 FUSIBLE
1-219-022-11 FUSIBLE
< VIBRATOR >
1.2K
470
470
10K
330
220
6.8K
470
180
220K
22K
100K
100
100
1K
1K
1K
1K
680
680
470
X601
X602
1-577-685-11 FILTER, CRYSTAL (16MHz)
1-579-161-11 VIBRATOR, CRYSTAL (45MHz)
************************************************************
*
A-4699-545-A BSL BOARD, COMPLETE
*******************
< CONNECTOR >
CN11 1-580-864-11 SOCKET, CONNECTOR (SMT) 10P
< HOLE ELEMENT >
H11
H12
8-719-987-62 DIODE LT140SAZ
8-719-987-62 DIODE LT140SAZ
< RESISTOR/CHIP CONDUCTOR >
R11
R12
R13
R14
R15
1-216-049-91 METAL CHIP
1-216-049-91 METAL CHIP
1K
1K
1-216-295-91 CONDUCTOR, CHIP (2012)
1-216-295-91 CONDUCTOR, CHIP (2012)
1-216-295-91 CONDUCTOR, CHIP (2012)
5%
5%
1/10W
1/10W
************************************************************
*
1-663-631-11 COAX BOARD
***********
< CAPACITOR >
C702
C703
C704
C705
C706
1-104-645-11 CERAMIC
1-164-732-11 CERAMIC
1-136-165-00 FILM
1-107-611-11 MICA
1-164-732-11 CERAMIC
1uF
0.1uF
0.1uF
100PF
0.1uF
20% 50V
20% 50V
5% 50V
5% 500V
20% 50V
Remark
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
1% 1/4W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/4W F
5% 1/6W
5% 1/6W
5% 1/6W
5% 1/2W F
5% 1/2W F
The components identified by mark
! or dotted line with mark
! are critical for safety.
Replace only with part number specified.
– 68 –
COAX
DISPLAY
FL RELAY FLEX RELAY FLEXIBLE FUSE
Ref. No.
C707
C708
Part No.
Description
1-126-023-11 ELECT
1-162-282-31 CERAMIC
< CONNECTOR >
100uF
100PF
20%
10%
Remark
25V
50V
Ref. No.
Part No.
Description Remark
R803 1-216-097-00 METAL CHIP 100K 5% 1/10W
************************************************************
*
1-653-906-11 FL RELAY BOARD
**************
< CONNECTOR >
CN701 1-580-771-11 PIN, CONNECTOR (PC BOARD) 3P
CN703 1-580-771-31 PIN, CONNECTOR (PC BOARD) 3P
< IC >
CN291 1-568-794-11 SOCKET, CONNECTOR 12P
* CN292
1-568-950-11 PIN, CONNECTOR 12P
************************************************************
IC702 8-759-242-70 IC TC7WU04F
< PIN JACK >
*
1-654-005-11 FLEX RELAY BOARD
****************
J701 1-507-567-71 JACK, PIN 1P (DIGITAL OUT COAXIAL)
< CONNECTOR >
< RESISTOR >
R701
R702
1-259-401-11 CARBON
1-259-412-11 CARBON
< COIL WITH CORE >
T701 1-459-795-11 COIL (WITH CORE)
************************************************************
*
*
C801
C802
C803
C804
C805
C806
C807
1-654-256-11 DISPLAY BOARD
*************
4-969-510-01 HOLDER (FL)
< CAPACITOR >
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-031-11 CERAMIC CHIP 0.01uF
1-163-031-11 CERAMIC CHIP 0.01uF
1-163-031-11 CERAMIC CHIP 0.01uF
1-163-031-11 CERAMIC CHIP 0.01uF
1-163-031-11 CERAMIC CHIP
1-163-031-11 CERAMIC CHIP
0.01uF
0.01uF
25V
50V
50V
50V
50V
50V
50V
< SWITCH >
S21
S22
1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT OUT)
1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT IN)
************************************************************
*
! C991
! C992
! C993
1-663-628-11 FUSE BOARD
**********
1-533-233-11 HOLDER, FUSE
< CAPACITOR >
1-113-924-11 CERAMIC
1-113-924-11 CERAMIC
1-113-925-11 CERAMIC
0.0047uF 20%
0.0047uF 20%
0.01uF
20%
250V
250V
250V
< CONNECTOR >
< FLUORECENT INDICATOR TUBE >
1-653-918-11 FLEXIBLE BOARD
**************
FLD801 1-517-357-11 INDICATOR TUBE, FLUORESCENT
< IC >
* CN991
1-564-321-21 PIN, CONNECTOR 2P
CN992 1-770-128-11 PIN, CONNECTOR 2P
CN993 1-564-321-00 PIN, CONNECTOR 2P
CN994 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
IC801 8-759-324-36 IC LC7570E
IC802 8-759-324-36 IC LC7570E
IC803 8-759-324-36 IC LC7570E
IC804 8-749-923-80 IC GP1U90XB
75
220
5% 1/6W
5% 1/6W
CN191 1-580-473-11 SOCKET, CONNECTOR 26P
CN192
************************************************************
! F991
! F992
1-580-460-11 SOCKET, CONNECTOR 26P
< FUSE >
1-532-279-00 FUSE, TIME-LAG (T0.5A/250V)
1-532-279-00 FUSE, TIME-LAG (T0.5A/250V)
< TRANSISTOR >
< LINE FILTER >
Q801
Q802
8-729-421-19 TRANSISTOR UN2213
8-729-424-18 TRANSISTOR UN2113-TX
! T991 1-421-915-11 COIL, LINE FILTER
************************************************************
R801
R802
< RESISTOR >
1-216-029-00 METAL CHIP
1-216-089-00 METAL CHIP
150
47K
5%
5%
1/10W
1/10W
The components identified by mark ! or dotted line with mark ! are critical for safety.
Replace only with part number specified.
– 69 –
KEY-L KEY-R LINE LOADING MOTOR LOADING SW
Ref. No.
Part No.
Description Remark Ref. No.
Part No.
Description Remark
*
A-4699-345-A KEY-L BOARD, COMPLETE
*********************
< CONNECTOR >
CN850 1-580-774-11 PIN, CONNECTOR (PC BOARD) 6P
* CN851
1-580-772-11 PIN, CONNECTOR (PC BOARD) 4P
R850
R851
R852
R853
< RESISTOR >
1-249-415-11 CARBON
1-249-417-11 CARBON
1-249-419-11 CARBON
1-249-421-11 CARBON
< SWITCH >
680
1K
1.5K
2.2K
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
< SWITCH >
S884
S885
S886
S887
S888
1-554-303-21 SWITCH, TACTILE (CHECK)
1-554-303-21 SWITCH, TACTILE (CLEAR)
1-554-303-21 SWITCH, TACTILE (FILTER)
1-554-303-21 SWITCH, TACTILE ( 0)
1-554-303-21 SWITCH, TACTILE ( ))
S889
S890
S891
1-554-303-21 SWITCH, TACTILE ( § OPEN/CLOSE)
1-554-303-21 SWITCH, TACTILE ( ”)
1-554-303-21 SWITCH, TACTILE (
P)
S892 1-554-303-21 SWITCH, TACTILE ( p)
************************************************************
*
1-663-629-11 LINE BOARD
**********
< CONNECTOR >
S850
S851
S852
S853
S854
1-554-303-21 SWITCH, TACTILE (ERASE)
1-554-303-21 SWITCH, TACTILE (FILE)
1-554-303-21 SWITCH, TACTILE (EDIT/TIME FADE)
1-554-303-21 SWITCH, TACTILE (TIME)
1-554-303-21 SWITCH, TACTILE (REPEAT)
S855 1-554-303-21 SWITCH, TACTILE (PLAY MODE)
************************************************************
*
CN871
CN872
D871
D872
D873
Q871
Q872
Q873
R879
R880
R881
R882
R883
R884
R885
R886
R887
R888
A-4699-344-A KEY-R BOARD, COMPLETE
*********************
< CONNECTOR >
1-580-775-11 PIN, CONNECTOR (PC BOARD) 8P
1-580-770-11 PIN, CONNECTOR (PC BOARD) 2P
< DIODE >
8-719-303-02 LED SEL2510C-D ( ”)
8-719-301-52 LED SEL2810A-C ( P)
8-719-046-41 LED SEL5521C-TP15 (FILTER)
< TRANSISTOR >
8-729-900-80 TRANSISTOR DTC114ES
8-729-900-80 TRANSISTOR DTC114ES
8-729-900-80 TRANSISTOR DTC114ES
< RESISTOR >
1-249-429-11 CARBON
1-249-429-11 CARBON
1-249-415-11 CARBON
1-249-417-11 CARBON
1-249-419-11 CARBON
1-249-421-11 CARBON
1-247-843-11 CARBON
1-249-415-11 CARBON
1-249-417-11 CARBON
1-249-419-11 CARBON
10K
10K
680
1K
1.5K
2.2K
3.3K
680
1K
1.5K
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
CN471 1-764-341-11 PIN, CONNECTOR (PCB) (L TYPE) 4P
CN472 1-764-341-31 PIN, CONNECTOR (PCB) (L TYPE) 4P
CN473 1-580-771-31 PIN, CONNECTOR (PC BOARD) 3P
D471
J471
R470
R471
R570
R571
< DIODE >
8-719-987-63 DIODE 1N4148M
< PIN JACK >
1-568-101-11 JACK, PIN 4P (LINE OUT FIXED/VARIABLE)
< RESISTOR >
1-249-637-11 CARBON
1-249-528-91 CARBON
1-249-637-11 CARBON
1-249-528-91 CARBON
< RELAY >
33
100
33
100
5%
5%
5%
5%
1/2W
1/4W
1/2W
1/4W
RY471 1-515-804-11 RELAY
************************************************************
*
1-653-907-11 LOADING MOTOR BOARD
*********************
< CONNECTOR >
*
CN272 1-506-469-11 PIN, CONNECTOR 4P
************************************************************
1-653-905-11 LOADING SW BOARD
*****************
< CONNECTOR >
* CN281
1-568-942-11 PIN, CONNECTOR 4P
< RESISTOR >
R889
R890
R891
1-249-406-11 CARBON
1-249-410-11 CARBON
1-249-406-11 CARBON
120
270
120
5% 1/4W
5% 1/4W
5% 1/4W
R281 1-249-427-11 CARBON
< SWITCH >
6.8K
5% 1/4W
< ROTARY ENCODER >
RV870 1-475-006-11 ENCODER, ROTARY
( ≠ AMS ± PUSH ENTER)
S281
S282
S283
1-692-193-11 SWITCH, PUSH (1 KEY) (IN)
1-692-193-11 SWITCH, PUSH (1 KEY) (OUT)
1-692-193-11 SWITCH, PUSH (1 KEY) (LD)
************************************************************
– 70 –
OPT POWER
Ref. No.
*
Part No.
Description
1-663-630-11 OPT BOARD
**********
< CAPACITOR >
Remark Ref. No.
C975
C976
C977
C978
C980
Part No.
Description
1-110-335-11 MYLAR
1-110-335-11 MYLAR
1-110-335-11 MYLAR
1-162-294-31 CERAMIC
1-164-159-11 CERAMIC
< CONNECTOR >
100PF
100PF
Remark
5% 50V
5% 50V
100PF 5% 50V
0.001uF
10% 50V
0.1uF
50V
C701 1-126-048-81 ELECT
< CONNECTOR >
10uF 20% 50V
C957
C961
C963
C970
C971
C972
C973
C974
C933
C934
C935
C936
C951
C952
C953
C954
C955
C956
C901
C902
C921
C922
C923
C924
C925
C926
C931
C932
*
*
CN702
IC701 8-749-921-12 IC GP1F32T (DIGITAL OUT OPTICAL)
************************************************************
* A-4699-570-A POWER BOARD, COMPLETE
***********************
* BB921
1-691-459-21 PIN, CONNECTOR (PC BOARD) 3P
< IC >
2-259-121-01 SCREW, TR
4-363-146-00 HEAT SINK, V. OUT
4-941-237-01 HEAT SINK
< BUS BAR >
1-566-940-11 BUS BAR 6P
CN921 1-764-327-11 PIN, CONNECTOR (PCB) (V TYPE) 4P
CN922 1-770-964-21 PIN, CONNECTOR (PCB) (V TYPE) 4P
CN923 1-770-965-31 PIN, CONNECTOR (PCB) (V TYPE) 5P
CN951 1-764-331-31 PIN, CONNECTOR (PCB) (V TYPE) 8P
* CN952 1-573-267-21 PIN, CONNECTOR 8P
< DIODE >
D921
D922
D923
D924
D931
D932
D933
D934
D951
D952
8-719-210-29 DIODE F10P10Q
8-719-210-29 DIODE F10P10Q
8-719-114-49 DIODE RD7.5JS-B2
8-719-115-98 DIODE RD10JS-T2B1
8-719-210-29 DIODE F10P10Q
8-719-210-29 DIODE F10P10Q
8-719-114-49 DIODE RD7.5JS-B2
8-719-975-85 DIODE ERB83-004
8-719-047-31 DIODE RBA-402L
8-719-210-21 DIODE 11EQS04
< CAPACITOR >
1-136-177-00 FILM
1-107-611-11 MICA
1-110-504-11 ELECT
1-136-165-00 FILM
1-124-724-11 ELECT
1uF
100PF
5% 50V
5% 500V
6800uF 20% 35V
0.1uF
5% 50V
47uF 20% 50V
D971
D972
D973
D974
D975
8-719-200-77 DIODE 10E2N
8-719-200-77 DIODE 10E2N
8-719-200-77 DIODE 10E2N
8-719-200-77 DIODE 10E2N
8-719-113-38 DIODE RD18ES-T2B1
1-106-343-00 MYLAR
1-107-611-11 MICA
1-110-397-11 ELECT
1-110-504-11 ELECT
1-136-165-00 FILM
1-124-724-11 ELECT
1-106-343-00 MYLAR
1-107-611-11 MICA
1-110-397-11 ELECT
1-126-017-11 ELECT
1000PF
100PF
47uF
5%
5%
200V
500V
1000uF 20% 63V
6800uF 20% 35V
0.1uF
5% 50V
20% 50V
1000PF 5% 200V
100PF 5% 500V
1000uF 20% 63V
6800uF 20% 16V
D976
ET920
IC921
IC951
IC952
IC953
8-719-111-61 DIODE RD3.9ES-T2B1
< GROUND TERMINAL >
1-537-770-21 TERMINAL BOARD, GROUND
< IC >
8-759-602-01 IC M5220P
8-759-604-86 IC M5F7807L
8-759-231-53 IC TA7805S
8-759-604-90 IC M5F7907L
1-126-027-11 ELECT
1-126-027-11 ELECT
1-124-556-11 ELECT
1-110-335-11 MYLAR
1-110-335-11 MYLAR
1-110-335-11 MYLAR
1-126-015-11 ELECT
1-126-027-11 ELECT
1-110-335-11 MYLAR
1-126-052-11 ELECT
1000uF
1000uF
2200uF
100PF
100PF
100PF
100uF
20%
20%
20%
5%
5%
20%
25V
25V
16V
50V
50V
5% 50V
3300uF 20% 16V
1000uF 20% 25V
100PF 5% 50V
35V
! PS921
! PS931
Q921
Q922
Q931
Q932
Q971
< IC LINK >
1-532-685-00 LINK, IC (0.8A)
1-532-685-00 LINK, IC (0.8A)
< TRANSISTOR >
8-729-203-05 FET
8-729-107-53 TRANSISTOR
8-729-203-05 FET
8-729-141-10 TRANSISTOR
8-729-140-97 TRANSISTOR
2SK30A-GR3
2SC2275-QP
2SK30A-GR3
2SA985A-QP
2SB734-34
1-126-048-81 ELECT
1-126-023-11 ELECT
1-126-023-11 ELECT
10uF
100uF
100uF
20%
20%
20%
50V
25V
25V
The components identified by mark ! or dotted line with mark ! are critical for safety.
Replace only with part number specified.
– 71 –
POWER SERVO
Ref. No.
! R901
! R902
R921
R922
R923
R924
R925
R926
R931
R932
R933
R934
R935
R936
R971
Part No.
Description
< RESISTOR >
1-219-016-91 FUSIBLE
1-219-034-91 FUSIBLE
1-249-520-11 CARBON
1-249-923-11 CARBON
1-249-923-11 CARBON
1-249-560-91 CARBON
1-247-714-11 CARBON
1-249-528-91 CARBON
1-249-520-11 CARBON
1-249-923-11 CARBON
1-249-923-11 CARBON
1-249-560-91 CARBON
1-247-714-11 CARBON
1-249-528-91 CARBON
1-259-444-11 CARBON
56
330
47
1K
1K
2.2K
1.2K
100
47
1K
1K
2.2K
1.2K
100
4.7K
Remark
5% 1/2W F
5% 1/2W F
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/4W
5% 1/6W
Ref. No.
C134
C135
C136
C137
C138
C139
C140
C141
C142
C143
C144
C145
C161
C162
C163
C171
C172
Part No.
Description
1-163-109-00 CERAMIC CHIP 47PF
1-163-121-00 CERAMIC CHIP 150PF
1-163-121-00 CERAMIC CHIP 150PF
1-163-121-00 CERAMIC CHIP 150PF
1-163-121-00 CERAMIC CHIP 150PF
1-163-038-00 CERAMIC CHIP 0.1uF
1-164-336-11 CERAMIC CHIP 0.33uF
Remark
5% 50V
5% 50V
5% 50V
5% 50V
5% 50V
25V
25V
1-163-141-00 CERAMIC CHIP 0.001uF
5% 50V
1-163-127-00 CERAMIC CHIP 270PF 5% 50V
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP 0.1uF
25V
25V
25V
1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
1-164-489-11 CERAMIC CHIP 0.22uF
1-164-492-11 CERAMIC CHIP 0.15uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP 0.1uF
10%
10%
16V
16V
25V
25V
R972
R973
C106
C107
C108
C109
C110
C111
C112
C113
C114
C115
1-259-460-11 CARBON
1-259-440-11 CARBON
22K
3.3K
100PF
0.22uF
1-164-232-11 CERAMIC CHIP 0.01uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-164-346-11 CERAMIC CHIP 1uF
5%
5%
1/6W
1/6W
C93
C94
C95
C96
C97
C101
C102
C103
C104
C105
< THERMISTOR >
TH903 1-806-882-11 THERMISTOR, POSITIVE
TH904 1-808-065-11 THERMISTOR, POSITIVE
************************************************************
*
A-4699-587-A SERVO BOARD, COMPLETE
**********************
< CAPACITOR >
1-124-995-11 ELECT
1-124-995-11 ELECT
1-124-995-11 ELECT
1-163-141-00 CERAMIC CHIP
1-126-162-11 ELECT
1-126-177-11 ELECT
1-126-177-11 ELECT
1-164-004-11 CERAMIC CHIP
220uF
220uF
220uF
0.001uF
3.3uF
100uF
100uF
0.1uF
20%
20%
20%
5%
20%
10%
10V
10V
10V
50V
50V
20% 10V
20% 10V
1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
1-163-133-00 CERAMIC CHIP 470PF 5% 50V
25V
1-163-133-00 CERAMIC CHIP
1-163-809-11 CERAMIC CHIP
1-163-145-00 CERAMIC CHIP
1-163-117-00 CERAMIC CHIP
1-164-489-11 CERAMIC CHIP
470PF
0.047uF
5%
10%
0.0015uF 5%
5%
10%
50V
25V
50V
50V
16V
50V
25V
25V
25V
16V
C173
C174
C175
C176
C177
C178
C201
C202
C203
C204
C251
C252
C261
* CN91
1-573-278-11 PIN, CONNECTOR 8P
CN101 1-568-795-11 SOCKET, CONNECTOR 12P
CN102 1-580-473-11 SOCKET, CONNECTOR 26P
CN103 1-580-781-11 PIN, CONNECTOR (PC BOARD) 7P
CN104 1-580-774-11 PIN, CONNECTOR (PC BOARD) 6P
CN105 1-580-771-11 PIN, CONNECTOR (PC BOARD) 3P
CN201 1-580-774-11 PIN, CONNECTOR (PC BOARD) 6P
CN202 1-580-775-11 PIN, CONNECTOR (PC BOARD) 8P
CN203 1-580-770-11 PIN, CONNECTOR (PC BOARD) 2P
CN251 1-580-774-11 PIN, CONNECTOR (PC BOARD) 6P
< DIODE >
D201
D202
D261
1-163-038-00 CERAMIC CHIP
1-164-336-11 CERAMIC CHIP
1-163-038-00 CERAMIC CHIP
1-163-038-00 CERAMIC CHIP
1-164-336-11 CERAMIC CHIP
1-163-038-00 CERAMIC CHIP 0.1uF
1-125-622-11 CAPACITOR
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-163-038-00 CERAMIC CHIP
1-164-232-11 CERAMIC CHIP 0.01uF
1-163-038-00 CERAMIC CHIP 0.1uF
1-126-177-11 ELECT
< CONNECTOR >
8-719-914-44 DIODE DAP202K
8-719-976-96 DIODE DTZ4.7C
8-719-938-07 LED
< IC >
0.1uF
0.33uF
0.1uF
0.1uF
0.33uF
0.1F
0.1uF
100uF
25V
25V
25V
25V
25V
25V
5.5V
25V
25V
25V
50V
25V
20% 10V
GL480 (STABILIZER DETECT)
C131
C132
C133
1-163-109-00 CERAMIC CHIP 47PF 5% 50V
1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
IC91 8-759-636-16 IC M51957AL
IC101 8-752-369-78 IC CXD2545Q
IC102 8-759-071-79 IC BA6297AFP
The components identified by mark
! or dotted line with mark
! are critical for safety.
Replace only with part number specified.
– 72 –
SERVO
R133
R134
R135
R136
R137
R138
R139
R140
R141
R142
R113
R114
R115
R116
R117
R118
R119
R121
R131
R132
R91
R92
R93
R101
R102
R103
R104
R105
R106
R107
R108
R109
R110
R111
R112
Ref. No.
Part No.
Description
IC103 8-759-100-96 IC uPC4558G2
IC104 8-759-071-79 IC BA6297AFP
IC105 8-759-071-79 IC BA6297AFP
IC201 8-752-884-95 IC CXP84124-068Q
IC202 8-759-336-84 IC LC3564SM-10
IC203 8-759-822-09 IC LB1641
IC261 8-749-010-61 IC IS471F
< TRANSISTOR >
Q101
Q102
Q103
Q104
Q201
Q202
8-729-424-18 TRANSISTOR UN2113-TX
8-729-421-19 TRANSISTOR UN2213
8-729-424-18 TRANSISTOR UN2113-TX
8-729-421-19 TRANSISTOR UN2213
8-729-424-08 TRANSISTOR UN2111
8-729-421-22 TRANSISTOR UN2211
< RESISTOR >
1-216-689-11 METAL CHIP
1-216-077-00 METAL CHIP
1-216-061-00 METAL CHIP
1-216-077-00 METAL CHIP
1-216-097-00 METAL CHIP
1-216-077-00 METAL CHIP
1-216-025-00 METAL CHIP
1-216-061-00 METAL CHIP
1-216-061-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-121-00 METAL CHIP
1-216-105-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-041-00 METAL CHIP
1-216-041-00 METAL CHIP
1-216-041-00 METAL CHIP
1-216-037-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-049-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-097-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-045-00 METAL CHIP
1-216-689-11 METAL CHIP
1-216-689-11 METAL CHIP
1-216-083-00 METAL CHIP
1-216-083-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-689-11 METAL CHIP
1-216-689-11 METAL CHIP
1-216-083-00 METAL CHIP
1-216-083-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-085-00 METAL CHIP
39K
27K
27K
33K
33K
27K
27K
33K
33K
39K
470
330
10K
1K
10K
100K
33K
680
39K
39K
39K
15K
3.3K
15K
100K
15K
100
3.3K
3.3K
10K
1M
220K
10K
470
470
Remark
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
0.5% 1/10W
0.5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
0.5% 1/10W
0.5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
0.5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
Ref. No.
R143
R144
R145
R146
R147
R148
R149
R150
R151
R152
R153
R154
R155
R161
R162
R163
R164
R165
R166
R167
Part No.
Description
1-216-093-00 METAL CHIP
1-216-093-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-085-00 METAL CHIP
1-216-308-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-097-00 METAL CHIP
1-216-001-00 METAL CHIP
1-216-001-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-097-00 METAL CHIP
1-216-075-00 METAL CHIP
1-216-091-00 METAL CHIP
1-216-093-00 METAL CHIP
1-216-093-00 METAL CHIP
1-216-093-00 METAL CHIP
1-216-097-00 METAL CHIP
1-216-065-00 METAL CHIP
10
10K
100K
12K
56K
68K
68K
68K
100K
4.7K
68K
68K
33K
33K
4.7
10K
10K
10K
100K
10
R182
R183
R184
R201
R202
R203
R204
R205
R206
R207
R168
R171
R172
R173
R174
R175
R176
R179
R180
R181
1-216-097-00 METAL CHIP
1-216-001-00 METAL CHIP
1-216-105-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-105-00 METAL CHIP
1-216-308-00 METAL CHIP
1-216-001-00 METAL CHIP
1-216-105-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
1-216-105-00 METAL CHIP
1-216-308-00 METAL CHIP
1-216-013-00 METAL CHIP
1-216-069-00 METAL CHIP
1-216-069-00 METAL CHIP
1-216-069-00 METAL CHIP
1-216-069-00 METAL CHIP
1-216-069-00 METAL CHIP
1-216-069-00 METAL CHIP
100K
10
220K
2.2K
2.2K
220K
4.7
10
220K
2.2K
2.2K
220K
4.7
33
6.8K
6.8K
6.8K
6.8K
6.8K
6.8K
R208
R209
R210
R212
R213
R214
R261
1-216-069-00 METAL CHIP
1-216-069-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-097-00 METAL CHIP
1-216-021-00 METAL CHIP
< VIBRATOR >
6.8K
6.8K
10K
10K
10K
100K
68
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
X201 1-577-082-11 VIBRATOR, CERAMIC (4MHz)
************************************************************
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
Remark
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
5% 1/10W
– 73 –
CDP-XA50ES
SW VR
Ref. No.
*
*
Part No.
Description
1-663-636-11 SW BOARD
********
1-696-874-21 LEAD (WITH CONNECTOR)
< SWITCH >
Remark Ref. No.
! T901
! T902
Part No.
Description
1-427-816-11 TRANSFORMER, POWER (for AUDIO)
Remark
1-427-817-11 TRANSFORMER, POWER (for DIGITAL)
************************************************************
! S991 1-572-267-51 SWITCH, PUSH (AC POWER) (1 KEY)
************************************************************
* 1-663-635-11 VR BOARD
*********
* 4-962-201-01 PLATE (HP), GROUND
#1
#2
#3
#4
#5
**************
HARDWARE LIST
**************
7-685-246-14 SCREW +KTP 3X8 TYPE2 NON-SLIT
7-682-248-09 SCREW +K 3X8
7-682-565-09 SCREW +B 4X16
7-682-548-09 SCREW (3X8)
7-685-880-09 SCREW +BVTT 4X6 (S)
(for GOLD)
C350
C351
C461
C561
< CAPACITOR >
1-136-165-00 FILM
1-136-165-00 FILM
1-162-290-31 CERAMIC
1-162-290-31 CERAMIC
< CONNECTOR >
0.1uF
0.1uF
470PF
470PF
5%
5%
10%
10%
50V
50V
50V
50V
#6
#7
#9
#10
#11
#12
#13
#14
#15
#16
7-685-646-79 SCREW, TAPPING
7-685-871-01 SCREW +BVTT 3X6 (S)
7-685-873-09 SCREW +BVTT 3X10 (S)
7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT
7-682-903-01 SCREW +PWH 3X5
7-685-645-79 SCREW +BVTP 3X6 TYPE2 N-S
7-682-902-11 SCREW +PWH 2.6X5
7-621-775-50 SCREW +B 2.6X10
7-621-772-30 SCREW +B 2X6
7-685-134-19 SCREW +PTPWH 2.6X8 (TYPE2)
CN351 1-764-345-11 PIN, CONNECTOR (PCB) (L TYPE) 8P
* CN352
1-580-772-11 PIN, CONNECTOR (PC BOARD) 4P
CN461 1-764-326-11 PIN, CONNECTOR (PCB) (V TYPE) 3P
IC350
J461
J461
L461
L561
< IC >
8-759-962-08 IC BA6208
< JACK >
1-750-162-61 JACK (LARGE TYPE) (PHONES) (BLACK)
1-779-219-11 JACK (LARGE TYPE) (PHONES) (GOLD)
< COIL >
1-412-473-21 INDUCTOR 0uH
1-412-473-21 INDUCTOR 0uH
< VARIABLE RESISTOR >
RV350 1-223-747-11 RES, VAR, CARBON 10K/10K
(LINE OUT PHONE LEVEL)
************************************************************
! 110
153
158
! 266
273
MISCELLANEOUS
**************
1-558-568-21 CORD, POWER
1-769-109-11 WIRE (FLAT TYPE) (12 CORE)
1-769-110-11 WIRE (FLAT TYPE) (26 CORE)
8-820-014-01 OPTICAL PICK-UP KSS-273B/J1N
1-653-918-11 FLEXIBLE BOARD
#17
#18
#19
#20
#21
7-628-253-00 SCREW +PS 2X4
7-627-852-58 SCREW, PRECISION +P 1.7X5 TYPE3
7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
7-685-872-09 SCREW +BVTT 3X8 (S)
7-685-246-19 SCREW +KTP 3X8 TYPE2 NON-SLIT
(for BLACK)
************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
1-473-944-11 REMOTE COMMANDER (RM-D950)
1-590-925-31 CORD, CONNECTION (AUDIO 1m)
3-707-584-21 COVER, BATTERY (for RM-D950)
3-858-365-11 MANUAL, INSTRUCTION
(ENGLISH, FRENCH, SPANISH, SWEDISH)
3-858-365-21 MANUAL, INSTRUCTION
(GERMAN, DUTCH, ITALIAN, PORTUGUESE) (AEP)
3-858-365-31 MANUAL, INSTRUCTION (CHINESE)
(Singapore)
M21
S21
S22
X-4945-920-1 MOTOR ASSY (SLED)
M271 X-4945-565-1 MOTOR ASSY (LOADING)
1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT OUT)
1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT IN)
The components identified by mark
! or dotted line with mark
! are critical for safety.
Replace only with part number specified.
9-960-813-11
Sony Corporation
Home A&V Products Company
– 74 –
97D0569-1
Printed in Japan © 1997. 4
Published by Service and Safety
Engineering Dept. (Shibaura)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 SERVICING NOTES
- 4 GENERAL
- 15 DISASSEMBLY
- 20 TEST MODE
- 22 ELECTRICAL ADJUSTMENTS
- 23 DIAGRAMS
- 40 EXPLODED VIEWS
- 46 ELECTRICAL PARTS LIST