FISHER Reference Manual, Rev. 04
Reference
Manual
Table of Contents
Web Site Technical Resources ................................. 4
Literature Number & Description (most used)........ 5
Blades & Attachments ............................................ 11
Minute Mount® Peculiar and Common
Attachments Index............................................. 11
MC Series Part Identification................................. 13
Blade Attachment Charts ...................................... 14
Conventional Pushbeam Identification .................. 16
Replacement Part Numbers for Weld
on Shoe Tube Holders....................................... 20
Base Angle Identification ....................................... 21
Minute Mount/Minute Mount® 2 RD/HD
M Blade A-Frame Identification ......................... 22
Conventional Peculiar and Common
Attachments Index............................................. 23
Cutting Edge/Cutting Edge Bolt Bag
Identification ...................................................... 26
Electrical Components............................................ 27
4-Port to 3-Port Isolation Module
Plug-In Harness Kit Cross Reference ............... 27
Isolation Module System Connector
Identification and Wiring .................................... 28
Harness Repair Ends ............................................ 29
Original Minute Mount Wiring to Isolation
Module System Cross Reference...................... 29
XtremeV™ or XLS™ Schematic w/o Plow Lights . 30
Straight Blade Schematic w/o Plow Lights ............ 30
E-Force Isolation Module System ......................... 31
Plug-In Harness Conversions for
LF/UF Headlamps ............................................. 32
Original Minute Mount Electrical System
Connector Identification and Wiring .................. 33
Minute Mount Electrical Kits Index ........................ 34
Conventional Electrical Kits Index ......................... 36
Hydraulic Components ........................................... 38
Minute Mount Hydraulic Kits Index........................ 38
Cartridge Identification Chart ................................ 40
Hydraulic Cylinder Identification ............................ 40
Hydraulic Hose Identification................................. 41
Pump Shaft Seals ................................................. 41
Conventional Hydraulic Kits Index ........................ 42
Recommended Tools .............................................. 44
Spreaders ................................................................. 45
Hopper and Tailgate Spreader Service Part
Identification ...................................................... 45
Spreader Gear Box Reference Chart .................... 46
Miscellaneous .......................................................... 50
Clevis Pin Identification ......................................... 50
"Dashed" Kit Numbers .......................................... 51
Safety Definitions
WARNING
Indicates a potentially hazardous situation
that, if not avoided, could result in death or
serious personal injury.
NOTE: Indicates a situation or action that can lead
to damage to your snowplow and vehicle or other
property. Other useful information can also be
described.
CAUTION
Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
NOTE: This manual is for reference only and was created to serve as an addition to the FISHER® Service
Training Manual. It contains information on noncurrent products that are often the subject of technical
questions and problems. This material is not complete, may not be accurate, and should not be used
in place of the Kit Selection Guide/eMatch or other regularly updated documents. Additional product
information is available on the Internet at www.fisherplows.com and www.homesteaderplows.com or
from the Fisher Engineering Technical Service Department.
Lit. No. 29032, Rev. 04
July 1, 2009
REFERENCE MATERIALS
Web Site Technical Resources
Located under the "Tech Support" section of our Web site (www.fisherplows.com) are some technical resources
that you should know about. These resources often go unused and can be a practical aid to help in snowplow
and spreader diagnosis and repair. The reference documents on the Web site can be printed and bound as a
manual for quick reference by Parts & Accessories employees or simply viewed online when needed.
There are 2 main headings under the "Guides" section on the Web site:
1.
Mechanic's
• Mechanic's Guides (all complete currently offered guides)
2. Schematics
• Schematics for the Minute Mount ® System with original headlamps
Located under the "Reference Materials" heading in the "For Our Distributors" section are the following
documents:
1.
Service Training Manual
• This workbook, updated each summer, is used at our Factory Authorized Service Training (FAST) schools.
• Each year, every FAST school attendee receives a hard copy of this manual. Distributors without attendees
are mailed copies.
2. Reference Manual
• This manual contains hard-to-find Conventional and Minute Mount System snowplow, as well as spreader,
information from many sources, including some of those listed above.
• The reference manual is a great resource to help you and your customers identify parts.
Lit. No. 29032, Rev. 04
4
July 1, 2009
LITERATURE
Minute Mount® & Minute Mount® 2 System Mount Kit Literature
Chevy/GMC
Dodge
Kit #
PL
II
Kit #
7125
7129
7138
7139
7142
7144
7146
7146-1
7148
7154
7154-1
7160
7161
7168
7169
7171
7175
7177
7182
6452
6454
6459
29042
29214
29043
7124
7130
7137
7141
7149
7153
7155
7157
7165
7167
7170-1
7170-2
7178
7180
7186
7189
21849
21930
26689
63804
64062
29126
27271
29185
29824
40962
Kit #
Mitsubishi
PL
Kit #
7126
7128
7131
7132
7136
7150
7152
7152-1
7159-2
7164
7172
7173
7174
7176
7183
7187
7188
Kit #
7147
7158
7166
7185
Lit. No. 29032, Rev. 04
6465
6478
20547
29044
20809
26201
26200
20607
21705
26207
25998
26077
68161
64014
64203
26678
26870
29354
26206
68162
64019
64025
64015
64204
26677
26871
29353
Ford
PL
II
6430
6457
6476
6485
42001
6496
21320
29031
26204
63890
29046
28504
64555
64463
64689
29513
69274
40876
Toyota
PL
II
6449
6435
6463
6480
21588
21410
29142
64065
26165
63803
64061
29127
27272
29186
29823
40963
7162
7162-1
7179
26861
27657
Kit #
International
PL
26203
Kit #
Jeep
PL
29045
27656
II
6467
21352
27055
7163
7163-1
48430
Kit #
Nissan
PL
26202
II
26376
7143
7190
41151
Kit #
Universal
PL
7156
7156-1
II
22507
7140
7151
7151-1
7151-2
21633
26205
22303
26563
28505
64554
64464
64690
29512
69273
40875
PL
29215
II
20570
41152
II
22036
26209
26208
II
20578
21988
27014
29566
27638
27638
29567
5
July 1, 2009
LITERATURE
Minute Mount ® & Minute Mount ® 2 System Mount Kit Literature
Owner's Manuals
MM2 SD, HD, XBLADE™, XLS™, XtremeV™
MM2 LD, RD/HD, X, MC (Isolation Module)
Lit. No.
A-Frames
HT Series™ (69450)
XLS (50810)
XtremeV (44675-1, 44685-1, 44695-1, 44775-1, 44785-1, 44795-1)
69381
50578
44226
MC A-Frame/Angle Frame (28665)
MC A-Frame/Angle Frame (27255-1)
MC (20703-1)
MC (8446-1, 27255)
HD (22168)
RD/HD M-Series (27597, 27598)
RD (27150)
SD, 6'-9" & 7-1/2' (27995-1)
LD, 6'-9" & 7-1/2' (27995-1)
LD, 7-1/2' (22175)
XBLADE (27510-1, 27512, 28100-1, 28200, 28510-1, 28520,
44916
LD, 6'-9" (22169)
MM2 EZ-V (Includes A-frame II) (28885, 28895)
MM2 MC Series (12/04-__) (29250, 29350)
MM2 MC Series (9/01-12/04) (27250, 27350)
MM2 SD Series (27775, 28069)
MM2 LD Series (27775, 28069)
27592
26945
26180
68257
26183
MM2 EZ-V® (Insta-Act®, Isolation Module)
MM (Insta-Act, Isolation Module)
MM EZ-V (Insta-Act, Isolation Module)
MM SEHP (Relay System)
Minute Mount 2 System Blades
29100-1, 29200, 29618-1, 29619-1)
Minute Mount System Blades
MM EZ-V (includes A-frame II) (21442, 26596)
MM MC (__-9/01)(22350, 21000)
M Series (27500, 28000, 28500, 29000)
MM LD Series (22609, 22075)
L Series (7657, 7658, 7659, 7761, 28850)
Accessories
XtremeV Blades
Back Drag Edge Kit (44281-1, 44282-2, 44283-2)
Blade Stop Kit (44473)
Blade Wing Extension (44610-1)
4-Piece Cutting Edge Kit (29675)
SnoFoil® Accessories
HT Series (69660)
RD/HD M Series (27100)
7-1/2'–10' RD/HD, LD & MC Series Blades
Shoe Kits
XLS Shoe Kit (50700)
XtremeV Curb/Wear (44850-1, 44851-1)
XBLADE Curb/Wear (27222)
Curb Guard Kits (44405, 44406)
LD, SD Series (26145)
HS Series (20505)
Other
Blade Stop Kit (26634)
Control Dual-Lock Fastener Mounting Kit
Removable Spring Tool (20043)
ProTube™ Guard (26239, 26240)
Ballast Retainer Kit (62849)
MM2 Emergency Parts Kit (27930)
Skid Plate Kit (20555)
License Plate Bracket (22366)
Lit. No. 29032, Rev. 04
44224
26405
26406
26407
26467
21462
PL
PL
21808
20801
26093
22231
21987
PL/II
29406
44815
44618
29665
PL/II
69687
26449
29644
PL/II
50699
44852
26683
44416
26147
20506
PL/II
26650
20275
6486
26244
28338
26374
20550
22358
Minute Mount 2 System Headgear
HT Series (69450
XLS (50600)
XtremeV (44600, 446500)
EZ-V (28888)
MC Series (29999)
HD/XBLADE Series (27777, 28900)
RD/HD/XBLADE Series (27777, 28900)
SD Series (27750-1)
LD Series (27750-1)
Minute Mount System Headgear
EZ-V (8840-1)
MC (8445, 8446-1, 27255)
HD (22250 w/M Blades)
HD (22250 w/L Blades)
RD/HD (22240 w/M Blades)
RD/HD (22240 w/L Blades)
HS/LD (22230)
LD (22135)
Rubber Deflectors
HT Series (69605)
XLS (50628)
XtremeV (44710)
EZ-V – 8-1/2' (21619)
EZ-V – 9-1/2' (26572)
XBLADE (8' & 9' only) (27600)
XBLADE (all blades) (27600-1)
MC Series (22390)
7-1/2' – 9' LD/RD/HD (All Series)
Lights
Mini Strobe (26018-1 and 26018)
Full Size Strobe (26019)
Mini Bar (26020)
Full Size Bar (26021)
PL
II
26947
with
27918 Headgear
20793
20796
27331
22227
22195
27639
27082
27476
68256
with
26457 Headgear
22264
22263
22195
PL
II
69381
50578
44226
27591
26156
27370
27475
27370
26181
69382
50579
44227
27589
26157
27446
27476
27374
26474
PL
II
21807
20796
26631
27331
26094
22195
26094
22195
22229
22228
22248
22249
22195
PL/II
69686
50690
29401
21894
26573
27605
26647
22395
26031
PL/II
26214
26415
26416
26417
Other
PL/II
Headlamp Extension Bracket Kit (28330)
Headlamp Extension Bracket Kit (29596)
28334
29597
6
July 1, 2009
LITERATURE
POLY-CASTER™, PRO-CASTER™ and SPREADER KIT LITERATURE
Description
POLY-CASTER
Poly Hopper II
Spreaders
POLY-CASTER
Poly Hopper
Spreaders
PRO-CASTER
Hopper
Spreaders
Serial #
OM
II
0901–Higher
94197
94194
95749
95742
94865
94867
0001–0608
0609–0711
0712 – Higher
0126–0302
0303–0401
0402–0608
0609–0805
0806 – Higher
Old-Style
Hopper
Spreaders
2600–3849
95617
95615
95903
95901
96208
96210
80324
80309
4809–4996
4997–5644
5645–7663
80357
80359
68880
68938
Accessories
Top Screen Fastener Repair Kit
95844
95921
96111
94869
(Offset)
95243
(Hydr)
95491
(Center)
95243
(Hydr)
96202
94635
94641
(RC)
94643
(HC)
N/A
94189
N/A
N/A
96378
94875
94647
96204
96200
94651
68964
(Std Cab
Control)
94647
(11-pin Cab
Control)
94871
N/A
95905
See
below*
See
below*
See
below*
94649
(Gas)
94651
(Hyd)
94637
* Drive Comp
PL
II
Briggs RC
68916
Briggs HD
68917
See
Hopper II
Tecumseh
68959
94493
POLYCASTER
96047
PRO-CASTER
0806 –
0126 –
Higher
0805
96212
Baffle Replacement Kit PL
94879
N/A
Old Style
94644
68819
Inverted Vee RC MS PL
68970
95969
96202
94873
Inverted Vee HC MS & SS PL
68971
68972
Ratchet Tie-Down Strap Kit PL
68791
Hold-Down Kit PL
68599
CHMSL Kit PL
96202
94873
Belt Drive Idler Kit II/PL
95707
Work Light Kit II/PL
95715
Lit. No. 29032, Rev. 04
N/A
68956
Vehicle Battery Kit II/PL
Inverted Vee RC SS PL
Parts Kit
PL
Cab
Control
& Elec
Comp
II/PL
96206
See OM for PL; see
II for Maintenance
94639
94633
Drive
Comp
PL
Chutes
PL
94191
94873
3850–4763
4764–4808
Body
Comp
PL
Durst
Gear
Case
PL
7
6456
July 1, 2009
LITERATURE
SPEED-CASTER™ & SPEED-CASTER™ 2 Spreaders
MOUNT
Under-Frame
Vehicle Make
Dodge
Ford
GM
In-Bed
Support Frame
Kit #
II
PL
II
PL
II
PL
27936
27949
27950
13666
68689
27949
68727
63827
63845
63844
13666
68689
63845
68727
67040-2
13761
68726
13666
68689
13761
68727
65780
13762
68721
13666
68689
13762
68727
67450
67460
68746
13666
68689
67460
68727
67500
67498
67491
13666
68689
67498
68727
64720
64722
64723
13666
68689
64722
68727
65890
13760
68719
13666
68689
13760
68727
67470
67477
68720
13666
68689
67477
68727
67510
67523
67524
13666
68689
67523
68727
67925
67523
95695
13666
68689
67523
68727
HOPPER
Electrical
Spreader
SPEED-CASTER
SPEED-CASTER 2
Serial #'s
OM
Hopper PL
Drive PL
II
PL
115297 – Higher
9511
68723
68725
13763
68723
202389–202649
13722
68757
68758
13763
68757
202650 – Higher
94418
94416
94415
13763
94416
Low-Profile Spreaders
MOUNT
Receiver Mount
Model #
Fixed Mount
SWING AWAY® Mount
Serial #
II
PL
II
PL
II
PL
N/A
94380
94381
94433
68518
94432
68519
Serial #
OM
Hopper PL
Drive PL
Electrical II
Electrical PL
Model 110
7192 – Higher
68661
68663
68664
13763
68666
Model 500
03010130000195331
95363
13763
95365
Model 1000
10001–10002
68661
68673
68674
13763
68666
10003 – Higher
94431
68673
68674
13763
94429
20237–20363
68661
68673
68674
13763
68666
20364 – Higher
94431
68673
68674
13763
94429
0806 – Higher
96073
96076
96076
13763
110, 1000, 2000
HOPPER
Model #
Model 2000
Model 2500
95365
MISCELLANEOUS
Literature # (Type)
Description
Literature #
Description
63689 (II)
63694 (II)
CHMSL Relay Kit SPEED-CASTER 95474 (II)
68689 (II)
CHMSL Relay Kit (Low Profile)
95640 (II/PL) Model 500/1000 Point of Purchase Display Stand
63694 (II)
Spreader Harness Repair Kit (LP)
P2178 (II)
Truck Protector
68587 (II)
Back Stop Kit
94837 (OM)
Under Tailgate Spreader (UTS)
68589 (II)
Top Screen Kit
94839 (II)
Under Tailgate Spreader (UTS)
68680 (PL)
Deflector Kit
94841 (PL)
Under Tailgate Spreader Trough
Spreader Harness Repair Kit
SPEED-CASTER
Low Profile Spinner Ring
95607 (II/PL) Low Profile Model 500 Screen Kit
95582 (II)
Deflector Kit – Model 500
94843 (PL)
Under Tailgate Spreader Spinner
94518 (II)
Speed Control w/Adapter
94844 (PL)
Under Tailgate Spreader Mount
Lit. No. 29032, Rev. 04
8
July 1, 2009
LITERATURE
Homesteader™ Personal Plow Literature
Description
PL
II
Off-Truck Components/Plow Gear (27550)
27551
27554
6'-8" Blade
27563
7'-4" Blade
27563
Shoe Kit
OI
OM
Warranty
27794
Hydraulics/DA Ram Assy & Scrape Lock Adj
27565
Fish-Stik Hand-Held Control
13715
27812
27814
Solenoid Joystick
6368
27815
27817
®
28033
Headlamp Aiming
27769
Headlamps
27767
Isolation Module (4-Port)
28562
28561
Isolation Module (3-Port)
29207
29206
Splash Shield Replacement Kit (24 x 18)
28268
Splash Shield Replacement Kit (32 x 24)
64685
Owner's Manual
27567
Warranty (1 Year – Personal Plow)
27569
Warranty (2 Years)
6416 / 6417
MOUNT KITS
Dodge 33903
27587
27586
Dodge 33913
29347
29346
Dodge 33923
40943
40942
Ford 1203
27647
27646
Ford 1213
28009
28008
Ford 1213-1
27057
27056
Ford 1223
27424
27423
Ford 1233
28477
28476
Ford 31243
29393
29392
Ford 31253
40925
40926
GM 1503
27652
27651
GM 1523
28026
28025
GM 1533
64415
64414
GM 1533-1
27262
27263
GM 31543
28363
28362
GM 31543-1
48363
48362
GM 31553
29413
29412
Jeep 3713
28048
28047
Jeep 3713-1
28431
28429
Jeep 3713-2
48431
48429
Jeep 3723
64609
64608
Jeep 42113
29722
29721
Jeep 42021
29231
29230
Jeep 42113
29722
29721
Nissan 31303
64646
64645
Nissan 31313
29317
29316
Toyota 2303
28058
28057
Toyota 2313
28265
28264
Toyota 32323
28864
28865
Toyota 32333
29580
29581
Lit. No. 29032, Rev. 04
9
July 1, 2009
LITERATURE
IM Elec. System
PL
28800, 28801, 28802 (New H13
Headlamps)
II
28810
Controls
PL
II
OI
8292 Joystick
6368
27815
27817
13715
27812
27814
28806 H13 Bulb Handling
–
28814
9400 Fish-Stik ®
29033 H13 Adapter Kit
–
29034
9700 EZ-V Hand-Held (6 Button)
29207
29206 &
29225
9800, 29600, 29800 EZ-V, XLS™ &
XtremeV™ Hand-Held (9 Button)
28561 &
44780
9900, 29700, 49900 EZ-V, XLS &
XtremeV Joystick
3-Port Module – All Parts
4-Port Module – All but 26640
26640 (Ford, International, MC)
28562
26500-1 (Central Hydraulics)
26645
26499
Repair Instructions for Controls with
PC Board
–
96455
–
48504
3-Port IM Adapters
II
OI
II
26641-1 HB-5 to 1A/2A
29209
–
**
27968-1 (2B to 2E)
29226
–
**
28027-2 (In-Line)
29547
–
28860-1 HB-5 to HB-2 (Mitsubishi FG)
29210
–
27767
26411
PL
9835-1
96355
48506
8435 (Old-Style Headlamps)
26199
96357
48503
–
9825-1
96445
48505
29266
9840-2
96444
96446
49700 HT Series™ Joystick
26705-1 On-Truck Wiring Kit
Hydraulics
–
®
27816
9825-1, 9835, 9840-2
21993
21842
9825-2
28442
–
9828-4
26527
**
48506
49800 HT Series Hand-Held
29056-1 (Lights to Relay)
29515
–
29234 & 29235 (Ford)
29236
–
29399, 29400 & 29400-1 2-pin (HB-3) to H11
29456
–
29033 H13
29034
9828-3
26151
9828-2
26468
26469
Tools
22147-1, 22150-1
–
27190
26470-2 Isolation Module Tester
26473
26497 (IA w/Relay System)
–
26496
29290-1 Diagnostic Harness Kit
29289
8225, 8240, 8425 (MM Only)
20751
8428 (MM Only)
21812
20996
–
26404
Flushing Procedure
Description
Literature Number
Part Number
Back-up/O-Ring Kit (Relief, quill, PO Check
Valve – EZ-V Blade)
66851
66781
EZ-V Hydraulic Parts
26527
9828-X
66762
66763
O-Ring/Back-up Ring Kit
28521
7632K-2
Valve Manifold Assy. Instructions
66782
None
Control (Plow) – Parts
96446
9700, 9800, 9900,
29600, 29700, 29800
Central Hydraulics – E-Force Lighting
26499
26500-1
Dodge Plug-in Harness ('99–'01) Original MM
Lighting (2 Light Non-DRL)
26017
26014
4-Port Isolation Module System
28561
Multiple
GM Plug-in Harness ('99–'02) Original MM
Lighting (Dedicated DRL)
26116
26070
Plow Light Repair (Original MM)
26363
8328
Tecumseh Engine Kit Installation Instructions
94493
Inlet Filter/Filter Kit (Insta-Act )
®
Lit. No. 29032, Rev. 04
–
OI
10
July 1, 2009
BLADES & ATTACHMENTS
NOTE: This index is not current and appears as it did in a 1997 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
11
July 1, 2009
BLADES & ATTACHMENTS
NOTE: This index is not current and appears as it did in a 1997 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
12
July 1, 2009
BLADES & ATTACHMENTS
MC Series Part Identification
Shown below are the A-frames, angle frames and blades produced for the Minute Mount ® and Minute Mount ® 2
System MC Series. The components separated by horizontal lines are not compatible with each other.
HEADGEAR
A-FRAME
ANGLE FRAME
BLADE
22350 & 21000
(Before Sept. '01)
3/8" thick spring
anchor plate
8446-1
3/4" diameter clevis
pins (measured at
cotter pin end)
I-Beam
®
20702
S Y S T E M
20703-1
2-piece base
angle on 10'
Square
I-Beam
No notches in
pivot plates
27255
1/2" thick spring
anchor plate
27250 & 27350
(Between Sept. '01
& Dec. '04)
27237
®
S Y S T E M
20703-1
Square
1" diameter clevis
pins (measured at
cotter pin end)
Tubular
®
S Y S T E M
28288
27850
27255-1
1-piece base
angle on 10'
Notches in
pivot plates
Tubular
1/2" thick spring
anchor plate
28665
Tubular
29250 & 29350
(After Dec. '04)
1" diameter clevis
pins (measured at
cotter pin end)
®
S Y S T E M
28639
27850
1-piece base
angle on 10'
Tubular
No notches in
pivot plates
Lit. No. 29032, Rev. 04
13
July 1, 2009
BLADES & ATTACHMENTS
Blade Attachment Charts – Minute Mount® System
22240 RD/HD Headgear Kit
1999–'02 All New GM 3/4 Ton Trucks
2001–'02 All New GM 1 Ton Trucks
29-1/8"
L Blade
22-1/2" cc
22168 A-Frame
33-3/4" hh
3-5/8"
8' HD L Blade
7658
8-1/2' HD L Blade
28850
8445 Headgear Assembly
Angle Frame
9' HD L Blade
7659
8440-1 Common Attachment Kit
29-1/8"
29-1/8"
24-1/2"
21484-1 Push Assembly
(Part of 8440)
25-1/4" cc
Outside to Outside
24-1/2"
20703-1
A-Frame
21874-3
A-Frame
(Part of 21442
or 26596)
35" hh
8446
A-Frame Kit
33-3/8"
26634 Blade Stop Kit
20702
Angle Frame
9' MC Blade
22350
10' MC Blade
21000
8-1/2' EZ-V® Blade
21442
9-1/2' EZ-V Blade
26596
cc = center-to-center measurement
hh = hole-to-hole measurement
Lit. No. 29032, Rev. 04
14
July 1, 2009
BLADES & ATTACHMENTS
Blade Attachment Charts – Minute Mount® System
22230 Headgear Kit
22135 Headgear Kit
25" cc
22135 Headgear Kit
29-1/8" cc
29-1/8" cc
22-1/2" cc
22-1/2" cc
19-1/4" cc
22169
A-Frame
27" hh
22240 RD/HD Headgear Kit
27" hh
22175
A-Frame
27" hh
22175
A-Frame
6-9/16"
6-9/16"
6-9/16"
6'-9" LD Blade
22069
1999–20_ Jeep
Wrangler
6'-9" LD Blade
22069
7-1/2' LD Blade
22075
22250 HD Headgear
29-1/8" cc
29-1/8" cc
L Blade
25-1/8" cc
22-1/2" cc
8562
A-Frame
36" hh
8627
A-Frame
Angle Frame
31-1/2" hh
3-5/8"
3"
7' RD L Blade
7761
7-1/2' RD L Blade
7657
8' HD L Blade
7658
8-1/2' HD L Blade
28850
9' HD L Blade
7659
cc = center-to-center measurement
hh = hole-to-hole measurement
Lit. No. 29032, Rev. 04
15
July 1, 2009
BLADES & ATTACHMENTS
Blade Attachment Charts –
Minute Mount and Minute Mount® 2 Systems with L Blade
®
Minute Mount System
and M Blade
Minute Mount 2 System
with L Blade
22240 RD/HD
Headgear Kit
(GMC/Chevy w/ 8–9 ft blade)
22250 HD Headgear
27454
Headgear
29-1/8"
cc
29-1/8" cc
29-1/8" cc
25-1/8" cc
25-1/8" cc
27150 A-Frame
27598
A-Frame*
33-3/4" hh
22-1/2" cc
31-1/4" hh
3"
27597
A-Frame*
33-7/8" hh
28000
8' M Blade
7-1/2' L Blade
7657
28500
8-1/2' M Blade
cc = center-to-center measurement
hh = hole-to-hole measurement
27500
7-1/2' M Blade
29000
9' M Blade
* To replace a conventional-system blade, use an M blade with the A-frame that matches the width between the
conventional A-frame's pushears.
Conventional Pushbeam Identification
Width
Spread
Part
Width (in)
Spread (in)
Weight (lb)
Part
Width (in)
Spread (in)
Weight (lb)
1510
27
22-1/2
25
5654**
31
25-1/2
43
1511
28-3/4
22-1/2
26
5697**
26-7/8
25-1/2
35
1513
27
25-1/2
33
5702**
33
25-1/2
23
4243**
23-3/4
22-1/2
24
5952
32-1/4
25-1/2
37
5098
25-1/4
19-1/4
16
5993
27
19-1/4
18
5165**
40-1/4
30
58
6013**
25
22-1/2
24
5326
26-1/2
19-1/4
17
5189**
35
30
5417**
29-5/8
19-1/4
18
5234**
36-1/2
30
5605
31-1/8
25-1/2
36
** This part is no longer available.
Lit. No. 29032, Rev. 04
16
July 1, 2009
BLADES & ATTACHMENTS
Blade Attachment Charts – Minute Mount® 2 System
Minute Mount 2 System
with M Blade and XBLADE™ Snowplows
27454
Headgear
29-1/8" cc
27777/28900*
Common
Attachment Kit
M Blade
28500
8-1/2'
25-1/8" cc
28000
8'
33-3/4"
hh
27598
A-Frame
2Q7
XBLADE
27500
7-1/2'
28100 (SS)/28200 (MS)**
29618(Poly)
8'
29000
9'
29100 (SS)/29200 (MS)**/29619 (Poly)
9'
28510 (SS)/28520 (MS)**
8-1/2'
Minute Mount 2 System
with EZ-V® Blade
27510 (SS)/27512 (MS)**
7-1/2'
27454
Headgear
28888
Common
Attachment Kit
29-1/8"
cc
27400 A-Frame
(Packed with blade)
27345
Push Assembly
2Q8
28885
8-1/2'
26634
Blade Stop Kit
(9-1/2' only)
28895
9-1/2'
Lit. No. 29032, Rev. 04
cc = center-to-center measurement
hh = hole-to-hole measurement
* The 28900 Common Attachment Kit
includes a silver lift arm.
** No longer available.
17
July 1, 2009
BLADES & ATTACHMENTS
Blade Attachment Charts –
Minute Mount 2, Homesteader™ and HT Series™ Systems
®
Minute Mount 2 System
with LD/SD Blade
27742
Headgear
(new)
29-1/8" cc
27750-1
Common
Attachment Kit
27775*
7-1/2'
32" hh
25-1/2" cc
27995-1
A-Frame
(old)
28069*
6'-9"
22075
7-1/2'
22069
6'-9"
HT Series Snowplow
Homesteader Personal Plow
27126
Plow Gear Frame
27550
Plow Gear
Kit
69518
Headgear
29-1/8" cc
27138
A-Frame
27112
Quadrant
69523
A-Frame
27547
6'-8"
69400
7'-6"
27549
7'-4"
cc = center-to-center measurement
hh = hole-to-hole measurement
* In some applications, be careful to
avoid hitting the lift arm with the blade.
Lit. No. 29032, Rev. 04
18
July 1, 2009
BLADES & ATTACHMENTS
Blade Attachment Charts – Minute Mount® 2 System
Minute Mount 2 System
with MC Blade
29999
Common
Attachment Kit
28665
A-Frame
Kit
26160
Headgear
29-1/8" cc
25-1/4" cc
35.4" hh
27850
A-Frame
28639
Angle Frame
29350
10'
44558
Headgear
(Frame Only)
29250
9'
44556-1
Push Assembly
2Q9
26757-1 (Yellow)
27560-1 (Silver)
Lift Arm Kit
29-1/8" cc
Minute Mount 2 System
with XtremeV™ Blade
44675-1 (MS)/
44775-1 (SS)
7-1/2'
44555-1
T-Frame
Minute Mount 2 System
with XLS™ Blade
26757-1
Lift Arm Kit
(Yellow)
44558
Headgear
(Frame Only)
29-1/8" cc
44685-1 (MS)/
44785-1 (SS)
8-1/2'
50669
A-Frame
44695-1 (MS)/
44795-1 (SS)
9-1/2'
50666
8'–10'
cc = center-to-center measurement
hh = hole-to-hole measurement
Lit. No. 29032, Rev. 04
19
July 1, 2009
BLADES & ATTACHMENTS
Replacement Part Numbers for Weld on Shoe Tube Holders
No Longer Manufactured
Model
Shoe Tube Holder
6-1/2 ft – 7 ft HS Series #A5090, #A5437 (Last Sold 4/98)
Accessory Kit
6 ft 9 in – 7-1/2 ft LD Series #28069, #27775
Accessory Kit
6 ft 9 in – 7-1/2 ft LD Series #22069, #22075
Accessory Kit
6-1/2 ft RD Series L Blade #7760 (Last Sold 6/94)
PN 27215
6-1/2 ft RD Series G Blade #A5569 (Last Sold 1/89)
PN 27215
7-1/2 ft – 8 ft RD/HD Series Patriots M Blade #27500P, #28000P
PN 26197
®
7 ft – 9 ft RD/HD Series L Blade #7761, #7657, #7658, #28850, #7659 (Last Sold 4/01)
PN 27215
7 ft – 7-1/2 ft RD Series G/H Blade #A5570, #A5563 (Last Sold 1/92)
PN 27215
8 ft – 9 ft HD Series H Blade #A5564, #A5565 (Last Sold 1/92)
PN 27215
8-1/2 ft – 9-1/2 ft EZ-V Series (1 Piece Center Flap) #28885, #28895
PN 20721
8-1/2 ft – 9-1/2 ft EZ-V Series (2 Piece Center Flap) #28885, #28895
PN 20721
8-1/2 ft – 9-1/2 ft EZ-V Series #21442, #26596 (Last Sold 8/03)
PN 20721
®
9 ft – 10 ft MC Series – #27250, #27350 (Last Sold 4/05)
9 ft – PN 27254; 10 ft – PN 27184
9 ft – 10 ft MC Series – #22350, #21000 (Last Sold 10/01)
9 ft – PN 22351; 10 ft – N/A
10 ft HC Series #A5134 (Last Sold 1/98)
N/A
Currently Manufactured
6 ft 9 in – 7-1/2 ft SD Series #28069, #27775
Accessory Kit
7-1/2 ft – 9 ft RD/HD Series M Blade #27500, #28000, #28500, #29000
PN 26197
7-1/2 ft – 9 ft X BLADE™ Series (-1 version)
Accessory Kit
7-1/2 ft – 9 ft X BLADE Series
Accessory Kit
8 ft – 10 ft XLS™ Series Blade #50810PL
Accessory Kit
9 ft – 10 ft MC Series #29250, #29350
Lit. No. 29032, Rev. 04
PN 28648
20
July 1, 2009
BLADES & ATTACHMENTS
Base Angle Identification – "L" Blade and "M" Blade
The base angle ears (provide half of the hinge of the trip-edge) for the L and M series blades are located flush
with the rear edge of the base angle. That distinguishes them from the G and H series blades which have the
base angle ears located approximately 9/16" in from the rear edge of the base angle.
The number of hinges depends upon the series and length of the blades. That number is the same as the number
of full ribs.
Blade Length/Series
Number of Ribs
L Blade
7-1/2' L Blade
5 Full Ribs
8' L Blade
6 Full Ribs
8-1/2' L Blade
8 Full Ribs
9' L Blade
8 Full Ribs
M Blade
7-1/2' M Blade (Early Production)
6 Full Ribs and 2 Partial Ribs
7-1/2' M Blade (Current Production)
8 Full Ribs
8' M Blade
8 Full Ribs
8-1/2' M Blade
8 Full Ribs
9' M Blade
8 Full Ribs
The base angles for the 8-1/2' and 9' lengths of the L and M series blades might be confused. All have 8 full ribs
and therefore 8 hinges. The center-to-center measurements between the ribs for the M series of blades are as
follows:
Blade Length/Series
A
B
C
D
E
F
G
8-1/2' M Blade
14-1/2"
21"
9-1/4"
10-1/4"
9-1/4"
21"
14-1/2"
9' M Blade
14-1/2"
24"
9"
10-1/4"
9"
24"
14-1/2"
A
B
C
D
E
F
Base angles of 8-1/2' and 9' lengths with different
spacing than shown above and with the base angle ears
located flush with the rear edge of the base angle would
be for L series blades.
Lit. No. 29032, Rev. 04
21
G
July 1, 2009
BLADES & ATTACHMENTS
Minute Mount®/Minute Mount 2 RD/HD M Blade A-Frame Identification
In 2002, the A-frames for the Minute Mount and Minute Mount 2 RD/HD Series were revised, extending their
lengths by 3", moving the lift chain attachment point and changing the gusset at the tip of the A-frame. When
replacing an old-style A-frame, be sure to use the A-frame directly to the right of it in the illustration below.
HEADGEAR
OLD-STYLE A-FRAME**
NEW-STYLE A-FRAME
22475 (Weldment)
26090 (A-Frame Kit)
27507 (Weldment)**
27597 (A-Frame Kit)
Flat
Gusset
Bent Gusset
Cross Brace
No Cross Brace
Notched
Notched
®
S Y S T E M
High Hole
Location
Low Hole
Location
22-1/2" ± 1/8"
Center to Center
Ear
Indented
22-1/2" ± 1/8"
Center to Center
26109 (Weldment)
27000 (Packed in Headgear Kit – MM2 only)
26410 (A-Frame Kit)
Flat Gusset
®
S Y S T E M
Ear
Indented
27598 (A-Frame Kit*)
Bent Gusset
No Cross Brace
*Notched
Cross Brace
*Notched
High Hole
Location
Low Hole
Location
25-1/2" ± 1/8"
Center to Center
Ear Not
Indented
27032 (Weldment)
27000 (Packed in Headgear Kit)
25-1/2" ± 1/8"
Center to Center
Ear Not
Indented
27477 (Weldment)
27777 (Packed in Headgear Kit)
27598 (A-Frame Kit)
Flat Gusset
Bent Gusset
Cross Brace
No Cross Brace
Not Notched
Not Notched
High Hole
Location
Low Hole
Location
25-1/2" ± 1/8"
Center to Center
Ear Not
Indented
25-1/2" ± 1/8"
Center to Center
Ear Not
Indented
* The 27598 A-frame kit has been changed and now contains the 27477 A-frame (MM2 only). For original Minute Mount applications,
the A-frame must be notched.
** No longer available.
Lit. No. 29032, Rev. 04
22
July 1, 2009
BLADES & ATTACHMENTS
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
23
July 1, 2009
BLADES & ATTACHMENTS
PECULIAR AND COMMON ATTACHMENT KIT INDEX – CONVENTIONAL MOUNT PLOWS
YEAR
VEHICLE
BLADE SIZE
BLADE TYPE
COMMON
ATTACH KIT
PECULIAR
ATTACH KIT
"L"
A4979B
AR275C
FORD
F-150 (4)
7' – 7761
Bronco (4)
7 1/2' – 7657
F-250 (6) (4)
7 1/2' – 7657
"L"
8' – 7658
1987–91
F-350 (4)
8' – 7658
"L"
9' – 7659
F-350 2WD (6) (4)
8' – 7658
9' – 7659
F-Super Duty 2WD
9' – 7659
1992–95
F-150 (4) (10)
7' – 7761
1992
Bronco (4)
7 1/2' – 7657
1992–95
F-250 (4) (6) (7)
7 1/2' – 7657
1992–95
F-350 (4)
8' – 7658
9' – 7659
1992–95
F-Super Duty 2WD
8' – 7658
9' – 7659
A4980B
A4980B
A4980B
AL286B
AL287C
"L"
A4980B
AL292B
"L"
A4980B
AL296B
"L"
A4979B
7113B
"L"
8' – 7658
A4981B
A4981B
A4980B
7114B
"L"
A4980B
7115B
"L"
A4980B
7118B
"L"
A4979B
7116B
DODGE
1972–88,
W150 (5)
7' – 7761
1992–93
1974–93
Ramcharger (5)
7 1/2' – 7657
1972–90
W250 (5)
7 1/2' – 7657
W350 (5)
8' – 7658
1991–93
A4981B
"L"
A4980B
9' – 7659
A4980B
W250 (5)
7 1/2' – 7657
A4981B
W350 (5)
8' – 7658
"L"
9' – 7659
A4980B
AL257D
7117B
A4980B
FOREIGN COMPACT/JEEP
1987–95
Wrangler
6 1/2' – A5090
7' – A5437
1985–95
Cherokee
6 1/2' – A5090
1985–92
Comanche
7' – A5437
FISHER ENGINEERING, ROCKLAND, MAINE 04841
"HS"
A5091
7101
"HS"
A5091B
AM265D
SUBJECT TO CHANGE
05/05/95
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
24
July 1, 2009
BLADES & ATTACHMENTS
PECULIAR AND COMMON ATTACHMENT KIT INDEX – CONVENTIONAL MOUNT PLOWS
YEAR
VEHICLE
BLADE SIZE
BLADE TYPE
COMMON
ATTACH KIT
PECULIAR
ATTACH KIT
1990–95
CHEV Kodiak, GMC Topkick
w-w/o Tilt Hood
10' – A5134
"HC"
6955
7105C
1980–94
FORD F-600, F-700
w-w/o Tilt Hood
10' – A5134
"HC"
6955
7102
1989–94
1989–95
IHC 4600 (1)
IHC 4700 (1) (9)
w-w/o Tilt Hood
10' – A5134
"HC"
6955
7140 (1)
1995
FORD F-700, F-800
w-w/o Tilt Hood (8)
10' – A5134
"HC"
6955
7136
COMMERCIAL
(1) Also requires use of (2) part number 7375 – 144" control cables which are sold as service parts only!
(2) Recommended with RPO VYU snowplow prep package
(4) Recommended with optional heavy duty front suspension package only – (F-150 3800 lb, F-250 4600 lb.
F-350 4800 lb, F-350 4 X 2 4000 lb)
(5) Recommended with snowplow prep package (AHH/AHD) only.
(6) Not for use on trucks with diesel engines.
(7) Requires removal of sway-bar if equipped.
(8) with 7000# Front GAWR.
(9) maximum 10,000# FGAWR.
(10) not for use on trucks with Quad shocks.
FISHER ENGINEERING, ROCKLAND, MAINE 04841
SUBJECT TO CHANGE
05/05/95
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
25
July 1, 2009
BLADES & ATTACHMENTS
Cutting Edge/Cutting Edge Bolt Bag Identification
Fisher PN
(# on C.E.) Description
# of
Holes
Punched
Top/
Center
1" x 5" x
6-1/2' Poly
9
Top
11
Top
7
Top
7
Top
8
Top
8
Top
8
Top
8
Top
8
Top
11
Top
10
Center
10
Center
10
Center
11
Center
(2) 5
Top
3-3/4", 6-3/4", 18-1/2", 25-1/4", 33"
(2) 5
Top
3-3/4", 6-3/4", 18-1/2", 25-1/4", 33"
(2) 5
Top
3-3/4", 6-3/4", 20-1/2", 29-3/8", 39"
(2) 5
Top
3-3/4", 6-3/4", 20-1/2", 29-3/8", 39"
(2) 5
Top
3-3/4", 6-3/4", 23-1/2", 32-1/2", 45"
8
Top
1-1/2", 13-3/4", 26-3/8", 38-3/4", 51",
63-1/2", 76", 88-1/2"
(2) 5
Top
2", 16", 30-1/4", 44-1/4", 47"
(2) 5
Top
2", 8", 22", 36-1/4", 50-1/4", 53"
11
Center
12
Top
(2) 5
Center
Material
5094
(6196)
6-1/2' HS
5485
(6197)
7' HS
1" x 5" x 7' Poly
27713
(27713)
27714
(27159)
6'-8" Homesteader™
Personal Plow
7'-4" Homesteader
Personal Plow
22215
(22152)
6'-9" LD/SD
22216
(22193)
7-1/2' LD/SD
5532
(6597)
7-1/2' H, L, M
(RD/HD/HT Series™)
5533
(6598)
8' H, L, M (HD)
26460
(26652)
8-1/2' M (HD)
5534
(6599)
9' H, L, M (HD)
28575
(28545)
7-1/2' XBLADE™
Snowplow
27580
(27426)
8' XBLADE Snowplow
1/4" x 5" x 6'-8"
Steel
1/4" x 5" x 7'-4"
Steel
1" x 6" x 6' 9"
Poly
1" x 6" x 7-1/2'
Poly
3/8" x 6" x 7-1/2'
Steel
1/2" x 6" x 8'
Steel
1/2" x 6" x 8-1/2'
Steel
1/2" x 6" x 9'
Steel
1/2" x 6" x 7-1/2'
Steel Reversible
1/2" x 6" x 8'
Steel Reversible
27585
(28391)
8-1/2' XBLADE
Snowplow
27590
(27427)
9' XBLADE Snowplow
44740-1
(44881)
7-1/2' XtremeV™
Snowplow
7-1/2' XtremeV
Snowplow
8-1/2' XtremeV
Snowplow
8-1/2' XtremeV
Snowplow
9-1/2' XtremeV
Snowplow
7-1/2' HD/HT Series
1/2" x 6" x 7-1/2'
Steel
8'-10" XLS™ Snowplow
1/2" x 6" x
8-1/2' EZ-V® Snowplow
49-3/4" Steel
1/2" x 6" x
9-1/2' EZ-V Snowplow
55-3/4" Steel
1/2" x 8" x 9'
9' MC
Steel
1/2" x 6" x 10'
10' HC
Steel
1/2" x 8" x
10' MC (2 pieces)
59-3/4" Steel
44742-1
(44882)
44741-1
(44883)
44743-1
(44884)
44744-1
(44886)
50678
(50625)
28408
(28406)
26593
(26592)
27362
(27359)
3507
(7082)
27239
(27238)
Lit. No. 29032, Rev. 04
1/2" x 6" x 8-1/2'
Steel Reversible
1/2" x 6" x 9'
Steel Reversible
(2) 3/8" x 6" x
37-3/4" Steel
(2) 1/2" x 6" x
37-3/4" Steel
(2) 3/8" x 6" x
40-3/4" Steel
(2) 1/2" x 6" x
40-3/4" Steel
(2) 1/2" x 6" x
46-3/4" Steel
26
Bolt Pattern from Edge
1", 10-1/2", 20", 29-1/2", 39", 48-1/2",
58", 67-1/2", 77"
1", 4", 13-1/2", 23", 32-1/2" 42",
51-1/2", 61", 70-1/2" 80" 83"
2-1/4", 15-1/4", 28", 40", 51-7/8",
64-3/4", 77-3/4"
2-1/4", 16-3/4", 32", 44", 55-7/8",
71-1/4", 85-3/4"
1-1/2", 9-3/8", 21-7/8", 34-1/4",
46-3/4", 59", 71-1/2", 79-1/2"
1-1/2", 13-7/8", 26-3/8", 38-3/4",
51-1/4", 63-5/8", 76", 88-1/2"
1-1/2", 14", 26-3/8", 38-7/8", 51-1/4",
63-1/2", 76", 88-1/2"
4-1/2", 17", 29-3/8", 41-3/4", 54-1/4",
66-3/4", 79", 91-1/2"
2-1/2", 18-1/2", 31-1/2", 44-1/2",
57-1/2", 70-1/2", 83-1/2", 99-1/2"
3", 6", 18" 30", 42", 54", 66", 78",
90", 102" 105"
1-1/2", 4-1/2", 26-3/4", 38-3/4",
51-1/4", 63-3/4", 76", 85-1/2", 88-1/2"
1-1/2", 4-1/2", 17", 29-3/8", 41-3/4",
54-1/4", 66-3/4", 79", 91-1/2", 94-1/2"
2-1/2", 5-1/2", 18-1/2", 31-1/2",
44-1/2", 57-1/2", 70-1/2", 83-1/2",
96-1/2", 99-1/2"
3", 6",18", 30", 42", 54", 66", 78",
90", 102", 105"
1-3/4", 4-3/4", 11-3/4", 23-3/4", 39",
54", 69", 84", 96", 103", 106"
3", 6", 18", 30", 42", 54", 66", 78",
90", 102", 114", 117"
2", 18", 30", 42", 58"
Bolt
Bag
PN
Bolt Size &
Qty
6602
7/16-14 x 2 (9)
6603
27574
27574
7/16-14 x 2
(11)
3/8-16 x 1 1/2
(7)
3/8-16 x 1 1/2
(7)
22217
1/2-13 x 2 (8)
22217
1/2-13 x 2 (8)
6600
1/2-13 x 2 (8)
6600
1/2-13 x 2 (8)
6600
1/2-13 x 2 (8)
6601
5/8-11 x 2 (11)
20763
5/8-11 x 2 (10)
20763
5/8-11 x 2 (10)
20763
5/8-11 x 2 (10)
6601
5/8-11 x 2 (11)
Part # 44894 Center
Cutting Edge Kit w/
Fasteners
5/8-11 x 2 (14)
6600
21610
(2)
26594
(2)
1/2-13 x 2 (8)
1/2-13 x 2 (5)
1/2-13 x 2 (6)
27363
3/4-10 x 2 (11)
7084
5/8-11 x 2 (12)
27236
3/4-10 x 2 (10)
July 1, 2009
ELECTRICAL COMPONENTS
4-Port to 3-Port Isolation Module Plug-In Harness Kit Cross Reference
Headlamp or Vehicle Type
4-Port Harness Kit
(module included)
3-Port Harness Kit
(module not included)
8436
8437-1
8438
27480
27780
28028
8439
29050
27890
8439
w/26640 Adapter
8439
w/26640 Adapter
29053
29053
w/29234 Adapter
29053
w/29235 Adapter
HB-1 or HB-5 Headlamps
29048
w/28027-2 Adapter if both high
HB-3 & HB-4 Headlamps
and low beams on vehicle are
ON in high-beam mode.
29052
2B or 2D or HB2 Headlamps
29051
HB-1 & HB-5 Headlamps
29050
8442
Dodge Sport Package
w/29056-1 Adapter
H13 Headlamps
28400
29049
8436
29050
Mitsubishi FG
w/26641 or 28860 Adapter w/26641-1 or 28860-1 Adapter
GM Topkick/Kodiak
8443
29054
GM C4500/5500
International
Ford F-650/700/800
Additional Electrical System Compatibility Notes
1.
Revisions to adapter kits 28027(-2), 26641(-1) and 28860(-1) are strictly due to modifications to the installation
instructions. No changes were made to the actual adapters.
2. The 3- and 4-Port Isolation Modules are not interchangeable.
3. The 3- and 4-Port Isolation Module Plug-In Harness Kits are not interchangeable.
4. The 2- and 3-Plug System Vehicle and Snowplow Battery Cables are not interchangeable. The
21924 snowplow battery cable and 63411 vehicle battery cable cannot be used on a new 2-Plug System
(e.g., XtremeV™ or XLS™ Snowplow).
5. To use an existing 4-Port Isolation Module System with an XtremeV or XLS Snowplow, adapter 29175 is
required.
6. Homesteader™ Personal Plows will continue to use 8435 headlamps, which are compatible with either 3- or
4-Port Isolation Module Systems.
7.
The 3-Port Isolation Modules—Green Label DRL (PN 29070* or 29070-1), White Label Non-DRL (PN
29060*) and Blue Label DRL (PN 29760-1**)—are packaged separately; both a plug-in harness kit and a
module must be purchased for a full installation.
* No longer available; Replaced by PN 29070-1.
** 2008 Ford Super Duty only.
NOTE: This list is to be used as a ordering guide and reference only. It is not a complete list of
recommended snowplow applications and should not take the place of the Kit Selection Guide/eMatch.
Lit. No. 29032, Rev. 04
27
July 1, 2009
ELECTRICAL COMPONENTS
Isolation Module System Connector Identification and Wiring
Straight Blade Control Connectors
Control Side
(end view)
6
3
5
2
4
1
Pin No.
Wire Color
1
White
2
Green
3
Brown
4
Black
5
Blue
6
Red
(pins)
Vehicle Side
(end view)
3
6
2
5
1
4
(sockets)
Pin No.
Wire Color
Function
1
Red/Yellow
+12V Feed
2
Light Green
Valve S2
3
Orange/Black
4
Brown/Red
5
Light Blue
Ground
+12V Switched
to Motor Relay
Valve S3
6
White/Yellow
Valve S1
EZ-V® Control Connector
3
7
11
14
Pin No.
Wire Color
Function
1
Light Blue w/Orange Stripe
Valve S6
1
2
Blue w/Orange Stripe
Valve S5
4
8
12
3
Black w/White Stripe
Valve S4
4
Light Green
Valve S3
(Front View)
5
Light Blue
Valve S2
6
White w/Yellow Stripe
Valve S1
7
Brown w/Red Stripe
Neg. Switched to Motor Relay
8
Red w/Yellow Stripe
+12V Feed
9
Black w/Orange Stripe
Ground
10
Brown w/Green Stripe
+12V to Motor Relay
Snowplow Control Harnesses (3- and 7-Pin)
Plow (End View)
1
2
3
4
5
Wire Color
1
Black/White
3-Pin
N/A
7-Pin
Valve S4
3
Light Blue
Valve S3
Valve S2
4
Light Green
Valve S2
Valve S3
6
= both 3- and 7-Pin
= 7-Pin only
= not used
7
Function
Pin No.
8 9 10 11
(Sockets)
6
Red
N/A
+12V Feed
8
Blue/Orange
N/A
Valve S5
9
White/Yellow
Valve S1
Valve S1
10
Lt Blue/Orange
N/A
Valve S6
Snowplow Lighting Harness (11-Pin)
Plow (End View)
7
1
8
2
9 10 11
3 4 5
(Pins)
Lit. No. 29032, Rev. 04
6
Pin No.
Wire Color
Function
Pin No.
Wire Color
Function
1
Black/White
PS Low Beam
7
Black/Orange
Ground
2
Black/Orange
Ground
8
Gray
Left Directional
3
White/Yellow
PS High Beam
9
Purple
Right Directional
4
White
DS High Beam
10
Brown
Parking Lights
5
Blue/Orange
PS Common
11
Light Blue
DS Common
6
Black
DS Low Beam
28
July 1, 2009
ELECTRICAL COMPONENTS
Harness Repair Ends
Repair ends are available for most wiring harnesses. When the end of a harness is damaged and must be
replaced, using a repair end eliminates the need to replace a complete harness and offers the ability to
accomplish a repair at a lower cost. The part numbers of available repair ends are:
Original Minute Mount® Wiring
Repair End Part
Description
22334K
7-Pin – Snowplow Side
22335K
9-Pin – Snowplow Side
8246
22336K
9-Pin – Vehicle Side
8275
22337K
12-Pin – Snowplow Side
8273
12-Pin – Vehicle Side
8276
22338K
Original Harness Part
8612
E-Force Isolation Module Wiring
Repair End Part
Description
27063K
3-Pin – Vehicle Control Harness (Straight Blade)
Original Harness Part
26345
27067K
7-Pin – Vehicle Control Harness (EZ-V Blade)
26346
®
Miscellaneous Electrical Kits
Repair End Part
Description
Original Harness Part
27070
6-Pin White Connector – Vehicle Side
26345
22123
Pin Kit – 14-Pin Receptacle (EZ-V Blade)
26346
63726
11-Pin – Vehicle Side (PRO-CASTER™ Spreaders)
66426
63692
4-Pin – Vehicle Side (Tailgate Spreaders)
63633
63693
4-Pin – Spreader Side (Tailgate Spreaders)
Double Fuse Cover – Pkg of 5 (3-Port Peculiar
Harnesses , XtremeV™ and XLS™ Hydraulic Units)
63634
29998
NOTE: Repair ends are not available for the 11-Pin E-Force Isolation Module Vehicle- or Snowplow-Side
Lighting Harnesses.
NOTE: The wire colors of the PRO-CASTER 11-Pin Repair End will not match those used for the 11-Pin
vehicle-side light harness.
Original Minute Mount® Wiring to Isolation Module System Cross Reference
NOTE: The following information applies only to Original Minute Mount Wiring and 3-Plug Isolation
Module Electrical Systems. The information does not apply to the new 2-Plug Multiplex Module Electrical
System (e.g., XtremeV, XLS and HT Series™ Snowplows).
The E-Force Isolation Module Electrical System should be used with all new installations; however, when
swapping an existing snowplow from one truck to another, it may be possible to use the Original Minute
Mount 2-Plug Wiring System. See the chart below to determine which trucks can use this system:
App. Years
Vehicles
Compatible w/Orig.
MM Wiring
Lit. No. 29032, Rev. 04
All Chevrolet/GMC
2002 & Prior
All Ford
2004 & Prior
Dodge 1500
2001 & Prior
Dodge 2500/3500
2002 & Prior
Jeep Wrangler
2004 & Prior
29
July 1, 2009
ELECTRICAL COMPONENTS
Schematic – XtremeV™ or XLS™ Snowplow Without Plow Lights/Isolation Module
Vehicle Cable Assembly – PN 42014
RED
–
Control
+
Battery
RED
TAN
BLK/ORN
WHT
BLK
TWO CONDUCTOR, TWISTED PAIR, SHIELDED
D
C
B
A
D
C
B
A
BLK
RED
RED
BLK
RED
RED
BLK
BLK
Vehicle Control Harness
PN 28587
RED
1
2
3
4
1 RED
2 GRN
3 WHT
4 BLK
4-Pin Plug
(Under Dash)
To Switched Accessory Lead
Cut off 4-pin plug and hard wire
vehicle control harness to relay.
Fuse
10 amp
(add in-line fuse)
Relay – PN 8293
Schematic – Straight Blade & EZ-V® Snowplow Without Plow Lights/Isolation Module
Battery
Cable – PN 22511
BLK/ORN
RED
Plow Battery
Cable – PN 21294
Plow Control Harness
(3-Pin) – PN 26359
Vehicle Battery Cable – PN 63411
RED
BLK/ORN
RED/BRN
RED/GRN
BLK
Motor
Relay –
PN 5794K-1
BLK/ORN
Battery
Vehicle Control Harness (3-Pin) – PN 26345
Re
To
Snowplow
Control
d
To Switched
Accessory
Dust Plug – PN 26420
Fire Wall
15-Amp Fuse (Park/Turn)
RED/WHITE
RED
RED/YEL
7.5-Amp Fuse
(Straight Blade Control)
Cut off 10-pin connector and
hard wire vehicle control harness
to relay.
GROUND
Relay – PN 8239
Lit. No. 29032, Rev. 04
30
July 1, 2009
ELECTRICAL COMPONENTS
E-FORCE ISOLATION MODULE SYSTEM
Used with SEHP Hydraulic Unit
REQUIRES:
Part Number
Plug-in harness kit & module (3-port) – see eMatch for applications
Plow lighting harness1
26347
Vehicle control harness
26345
Plow control harness
26359
Motor solenoid
5794K-1
Red cable, 22" battery cable
22511
Vehicle cable assembly
63411
Panel mount
56526
Dust cover
26420
Light kit
8435 or 28800
2
Plug cover
8291K
Parts bag (includes fuse tops, rubber grommets, etc.)
8737
If you order Harness Kit PN 26431, it includes:
1
2
Plow control harness
26359
Vehicle control harness
26345
Vehicle cable assembly
63411
Plug cover
8291
Plow light harness required only if older 8416 or 8417 plow lights are used instead of the 8435 or 28800 light kit.
Would replace 8416 or 8417 plow lights.
Lit. No. 29032, Rev. 04
31
July 1, 2009
ELECTRICAL COMPONENTS
Plug-In Harness Conversions for LF/UF Headlamps
Although there is no Isolation Module plug-in harness available for LF/UF headlamps, it is still possible to install
a new FISHER® snowplow with the Isolation Module electrical system on vehicles with these headlamps. Note,
however, that installation on these vehicles does require modification of the existing vehicle wiring. To install an
Isolation Module system on a vehicle with LF/UF headlamps, cut off and discard the headlamp connectors from
the plug-in harness(es) noted in the illustrations below, then splice the wires from the plug-in harness(es) into
the vehicle headlamp wiring as shown. Be sure to follow the illustration for the proper Isolation Module (3-Port or
4-Port). For complete Isolation Module installation instructions and recommended splicing procedures, see the
Isolation Module installation instructions.
4-Port Isolation Module
A
B
(Wire Side View)
(Wire Side View)
A B
Low Beam
Connector
(H4703 Bulb)
Common
(Ground)
Low Beam
Common
(Ground)
High Beam
High Beam
Connector
(H4701 Bulb)
SPLICE
SPLICE
SPLICE
Low Beam
Ground
High Beam
SPLICE
Ground
High Beam In (GRN)
Common In (BLU)
SPLICE
Low Beam In (YEL)
High Beam Out (RED)
Low Beam Out (ORN)
26349/26354 Plug-In Harness
(in 8436 Plug-In Harness Kit)
-or26353/26356 Plug-In Harness
(in 8439 Plug-In Harness Kit)
Common Out (LT BLU)
SPLICE
Vehicle Wiring
3-Port Isolation Module
A
B
(Wire Side View)
(Wire Side View)
A B
Low Beam
Connector
(H4703 Bulb)
SPLICE
High Beam
Common
(Ground)
Low Beam
Common
(Ground)
High Beam
Connector
(H4701 Bulb)
SPLICE
Low Beam
Ground
SPLICE
High Beam
SPLICE
Ground
Common In (COM-CJ)
High Beam In (HIGH-AB)
High Beam Out (HIGH-CD)
SPLICE
Low Beam In (LOW-BA)
Low Beam Out (LOW-BE)
28464 Plug-In Harness
(in 29051 Plug-In Harness Kit)
Common Out (COM-AK)
SPLICE
Vehicle Wiring
Now Available: PN B62225-1 Headlamp Adapter Kit H13 to LF/UF
Lit. No. 29032, Rev. 04
32
July 1, 2009
ELECTRICAL COMPONENTS
Original Minute Mount® Electrical System Connector Identification and Wiring
Straight Blade Control Connectors
Control Side
(end view)
6
3
5
2
4
1
Pin No.
Wire Color
1
White
(pins)
2
Green
3
Brown
4
Black
5
Blue
6
Red
Vehicle Side
(end view)
Wire Color
Function
1
Red
+12V Feed
2
Light Green
Orange/
Black
Valve S2
Pin No.
3
6
2
5
3
1
4
4
(sockets)
Ground
5
Light Blue
+12V Switched
to Motor Relay
Valve S3
6
White/Yellow
Valve S1
Brown/Red
EZ-V® Control Connector
3
7
11
14
Pin No.
Wire Color
Function
1
Light Blue w/Orange Stripe
Valve S6
1
2
Blue w/Orange Stripe
Valve S5
4
8
12
3
Black w/White Stripe
Valve S4
4
Light Green
Valve S3
5
Light Blue
Valve S2
6
White w/Yellow Stripe
Valve S1
7
Brown w/Red Stripe
Neg. Switched to Motor Relay
8
Red
+12V Feed
9
Black w/Orange Stripe
Ground
10
Brown w/Green Stripe
+12V to Motor Relay
(Front View)
Snowplow Control Harnesses (7-, 9- and 12-Pin)
Plow (End View)
1
7
2
8
3
4
5
6
9 10 11 12
(Sockets)
= 7-, 9- and 12-Pin
= 7- and 12-Pin only
= 9- and 12- Pin only
= 12-Pin only
Wire Colors
Pin
No.
7-Pin
9-Pin
12-Pin
1
N/A
White/Yellow
White/Yellow
Valve S1
2
Black
Black
Black
Low Beam6
3
N/A
Light Green
Light Green
Valve S2
Light Blue
Light Blue
Valve S3
1
1
4
N/A
5
Black/Orange3
6
White
White
White
High Beam
7
N/A
N/A
Black/White
DS Low Beam
8
N/A
N/A
Dk Blue/Orange
PS Low Beam
Ground
9
Gray
Gray
Gray
Left Directional
10
Purple
Purple
Purple
Right Directional
11
Brown
Brown
Brown
Parking Lights
12
Orange/Black 2
N/A
Lt Blue/Orange
Low Beam
Ground5
Black/Orange3,4 Black/Orange3,4
DS and PS
Main Ground
3
Ground for headlamp relays only
1
2
Lit. No. 29032, Rev. 04
Function
33
Ground
On early rev. harnesses, black/orange wire is
ground for motor relay, control and headlamp relays
5
DS only on 12-pin harnesses
6
PS only on 12-pin harnesses
4
July 1, 2009
ELECTRICAL COMPONENTS
NOTE: This index is not current and appears as it did in a 1997 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
34
July 1, 2009
ELECTRICAL COMPONENTS
NOTE: This index is not current and appears as it did in a 1997 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
35
July 1, 2009
ELECTRICAL COMPONENTS
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
36
July 1, 2009
ELECTRICAL COMPONENTS
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
37
July 1, 2009
HYDRAULIC COMPONENTS
NOTE: This index is not current and appears as it did in a 1997 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
38
July 1, 2009
HYDRAULIC COMPONENTS
NOTE: This index is not current and appears as it did in a 1997 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
39
July 1, 2009
HYDRAULIC COMPONENTS
Cartridge Identification Chart
Stamped # HydraForce
Stamped # Deltrol
Fisher Part Number
SF08-2015
N/A
44335
SV08-30
N/A
7636K-1
SV08-31
DSV2-080-3-N-C7
66608K
SV08-40
DSV2-080-4CO-N-C25
7637K
SV08-41
N/A
49457
SV08-43
N/A
66783K
SV08-45
N/A
49453
SV08-2004
DSV-080-2NCP-N-C66
7634K-1
SVCV08-20
N/A
44331
Hydraulic Cylinder Identification
LENGTH – EXTENDED
LENGTH – RETRACTED
BARREL LENGTH
90° PORT
B
DA Cylinder
Piston
Diameter
A
0° PORT
Part
Number
Description
Retracted
Length
Extended
Length
Dia.
"A"
Dia.
"B"
Dia.
"C"
Port
Location
C
Piston
Dia.
Barrel
Length
With NPTF Port/Packing Nut
A5096
1-1/2 x 6
13-1/4
19-1/4
1-1/2
1
1
0°
11-3/8
A3463
2 x 10
17-1/4
27-1/4
2
1
1
0°
15-1/4
A3464
2 x 12
19-1/4
31-1/4
1
1
1
90°
17-1/4
A5166K
2 x 16
23-1/4
39-1/4
2
1-1/4
1-1/4
90°
21
20116K
1-1/2 x 10
17-3/16
26-7/8
1-1/2
1
1
0°
15-1/4
20117K
1-1/2 x 12
19-1/2
31-1/4
1-1/2
1
1
90°
17
17
27
1-1/2
1
1
0°
15-3/8
With SAE O-Ring Port/Gland Nut
56600K
1-1/2 x 10
56718
1-1/2 x 6
13-1/4
19-1/4
1-1/2
1
1
0°
11-3/8
56603K
1-1/2 x 12
19-1/2
31-1/2
1-1/2
1
1
90°
17
56740
2 x 10
17
27
2
1
1
0°
14-7/8
56709F
2 x 10 DA
17-1/4
27-1/4
1-1/2
1
1
90°
2
14-3/4
44340
1-3/4 x 11 DA
18-1/4
29-1/4
1-1/2
1
1
90°
1-3/4
15-3/4
49461
1-1/2 x 10
17
27
1-1/2
1
1
90°
15-1/4
B60347
XLS™ Wing Cyl
29-9/16
40-1/2
1
5/8
5/8
* 90°
24-1/2
56772K
1x7
13-1/2
20-1/2
1
1/2
1/2
90°
11
27204
1-1/2 x 6 DA
13
19-3/16
1
1/2
1/2
* 90°
1-1/2
11-1/2
69668
2 x 6-3/4 DA
12.96
19.71
1
1/2
5/8
90°
2
11-9/16
69670
1-1/2 x 8
16.68
24.83
1-1/2
1
1
0°
13-1/4
* The B60347 and 27204 are unique cylinders and have multiple ports
Lit. No. 29032, Rev. 04
40
July 1, 2009
HYDRAULIC COMPONENTS
Hydraulic Hose Identification
SAE O-Ring End
Part
5749
56765
56592
4428**
56754
3074
56598
2707*
8728
376
5223*
56710
4424
56599
56599
44315
44348
NPTF End
Length (in) Type
Fittings
Bulk
LP
N/A
8
HP
JIC to JIC
16
HP
1/4" JIC to JIC
18
HP
1/4" NPTF to SAE O-Ring
18
HP
1/4" JIC to JIC
22
HP
1/4" NPTF to 1/4" NPTF
22
HP
1/4" JIC to JIC
26
HP
3/8" NPTF to 1/4" NPTF
28
HP
1/4" NPTF to 1/4" NPTF
32
HP
1/4" NPTF to 1/4" NPTF
32
HP
3/8" NPTF to 1/4" NPTF
32
HP
1/4" JIC to JIC
36
HP
1/4" NPTF to 1/4" NPTF
36
HP
JIC to JIC
36
HP
1/4" JIC to JIC
38
HP
3/8" JIC to JIC
42
HP
3/8" JIC to JIC
LP = Low Pressure
Part
375
56591
44316
4472**
1664
5193
2503**
44867
1665
5192
2504**
44868
6066*
2518**
2516**
1685**
JIC End
Length (in) Type
42
HP
42
HP
45
HP
48
HP
54
HP
54
HP
54
HP
57
HP
60
HP
60
HP
60
HP
60
HP
66
HP
66
HP
72
HP
72
HP
Fittings
1/4" NPTF to 1/4" NPTF
1/4" JIC to JIC
3/8" JIC to JIC
1/4" NPTF to SAE O-Ring
1/4" NPTF to SAE O-Ring
1/4" NPTF to 1/4" NPTF
3/8" NPTF to 1/4" NPTF
3/8" JIC to JIC
1/4" NPTF to SAE O-Ring
1/4" NPTF to 1/4" NPTF
3/8" NPTF to 1/4" NPTF
3/8" JIC to JIC
1/4" NPTF to 1/4" NPTF
3/8" NPTF to 1/4" NPTF
3/8" NPTF to 1/4" NPTF
1/4" NPTF to SAE O-Ring
HP = High Pressure
* This part will no longer be available once existing inventory is depleted.
** This part is no longer available.
Control Cable Identification
Part
A4949
A4922
A5701
A4488
6027
A5461
A4926
A2844
A2845
A4489
A2846
Length (in)
30
32
36
40
45
67
78
78
78
84
84
Use
SLC Cable
SLC Cable
SLC Cable
SLC Cable
SLC Cable
SLC Cable
SLC Cable
Angle Cable
Raise Cable
SLC Cable
Angle Cable
A2847
84
Raise Cable
Part
Length (in)
Use
A4490
90
SLC Cable
A2848
90
Angle Cable
A2849
90
Raise Cable
A5930
90
Adjustable Cable
A5931*
90
Nonadjustable Cable
A5843**
108
Nonadjustable Cable
A5844
108
Adjustable Cable
7375
144
Adjustable Control Cable
9240
300
Throttle Cable – To be Obsolete
A5929
90
SLC w/Cables
A5795
108
SLC w/Cables
4418
* This part is no longer available. PN A5930 should be used in its place.
** This part is no longer available. PN A5844 should be used in its place.
Ball Stud Retainer Clip
Used in Control PN 4419
T-Handle: Raise PN 4074
Angle PN 4075
}
To Be
Obsolete
Pump Shaft Seals for PN A2311 and A5075 Belt Drive Pumps
Measure the outside diameter of the seal.
Lit. No. 29032, Rev. 04
1" OD
PN 2768
1-1/4" OD
PN 5034 (Also found in kit PN A5038K seal with snap ring
41
July 1, 2009
HYDRAULIC COMPONENTS
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
42
July 1, 2009
HYDRAULIC COMPONENTS
NOTE: This index is not current and appears as it did in a 1995 Parts & Service Manual. It is to be used for
reference and should not take the place of the Kit Selection Guide/eMatch. Kits listed may no longer be available.
Lit. No. 29032, Rev. 04
43
July 1, 2009
RECOMMENDED TOOLS – Available from your FISHER® outlet
Pressure Test Kit (PN 56686)
Motor Bearing Sleeve Repair Kit
(PN 64589)
Requires 3/8"-24 x 4" bolt
to service XtremeV and
XLS valve blocks.
XtremeV™/XLS™ adapter PN 6-4F50X Parker
Packing/Gland Nut Removal Tool
(PN 26612)
Replacement
Bearing Sleeve
w/O-Rings – PN 64596
Poppet Seat Service Tool
(PN 28530)
Pump Shaft Seal Repair Kit
(PN 28856)
PN 28877
Requires
1/4"-28 x 4-1/2" bolt
to service XtremeV
and XLS valve blocks.
Trip Spring Removal Tool
(PN 20043-1)
3- & 4-Port Isolation Module Tester
(PN 26470-2)
Adapter (PN 29294-1)
(for all non "-1" Tester kits)
1
Diagnostic Harness Kit
for multi-plex
(PN 29290-1)
2
3
4
TURN SIGNAL
ISOLATION MODULE
TESTER
POWER
ON
ON
ON
OFF
OFF
OFF
LOW BEAM
LOW BEAM
HIGH BEAM
DEDICATED DRL
BULB SYSTEM
HIGH BEAM
HIGH
BEAM #2
HIGH BEAM #2
CONTROL POWER
A
A
POS (+)
ON
LEFT
PLOW ATTACHED
IGNITION SWITCH
HIGH BEAM #2
HIGH BEAM
RIGHT
NEG (-)
HEAD LAMP
COMMON
OFF
TURN SIGNAL
IGNITION
SWITCH
HIGH BEAM
LOW BEAM
ON
HIGH
ON
LOW BEAM
OFF
TURN SIGNAL
PLOW
ATTACHED
PARK LIGHTS
B
Lit. No. 29032, Rev. 04
B
DOUGLAS DYNAMICS, L. L. C.
44
LOW
HEAD LAMP
OFF
PARK LAMP
PART NUMBER 26471
July 1, 2009
SPREADERS
Hopper and Tailgate Spreader Service Part Identification
Chutes
Part
9189
9194
9031
9032
9107
9108
68920
68921
95424-1
95425-1
95426-1
95427-1
Description
RC MS – 14"
RC MS – 26" ext.
RC SS – 14"
RC SS – 26" ext.
HC MS – 31"
HC MS – 19"
HC SS – 31"
HC SS – 19"
MS – Belt Drive – 14"
SS – Belt Drive – 14"
MS – Belt Drive – 26"
SS – Belt Drive – 26"
Serial #s
ALL Non PRO-CASTER™ Spreaders
ALL Non PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
Original PRO-CASTER Offset Chutes*
Part
Application
Part
Application
Part
Application
Part
Application
94357* 14" MS
94924* 14" SS
94474* 26" MS
94940* 26" SS
94357-1* 19" MS
94924-1* 19" SS
94474-1* 26" MS
94940-1* 26" SS
Replacement Belt Drive Chutes w/Rework Kit 95496 (MS)* or 95497 (SS)*
95424-1* 14" MS
95425-1* 14" SS
95426-1* 26" MS
95427-1* 26" SS
* No longer available.
Roller Chains
Part
68351
68350
68431
9225
68417
9188
9220
20325
20341
95778
78075
Description
#40 – 26-1/2" RC – Spinner
#40 – 29-1/2" RC – Drive
#40 – 30-1/2" HC – Spinner
#40 – 35" RC – Drive
#40 – 36-1/2" HC – Drive
#40 – 38" RC – Spinner
#40 – 39" RC – Drive
#40 – 42" HC – Spinner
#40 – 47" HC – Drive
#40 – 63" POLY-CASTER™ ONLY
#40 – 29-1/2" POLY-CASTER II ONLY
Part
20334
20335
Description
8' HC – 16" 124 link
10' HC – 16" 153 link
68349
8' RC MS & SS – 11.65" 123 link
9177
94462
8' RC MS & SS – 11.875" 123 link
7' RC MS & SS – 11.65" 108 Link
Serial #s
3850–4808, 4809 – Higher
3850–4808, 4809 – Higher
3850–4808, 4809 – Higher
0000–0732
3850–4808, 4809 – Higher
0000–3849
0733–3849
2092–3849
2092–3849
ALL
ALL
Conveyor Chains**
68474
8' HC MS & SS – 15.65" 123 link
8' MS & SS – 15.65" 123 link
68435
94898
95361
78076
94898
10' HC MS & SS – 15.65" 153 link
10' MS & SS – 15.65" 153 link
7' MS & SS – 15.65" 108 link
9' MS & SS – 15.65" 138 link
7' POLY-CASTER II – 15.65" 99 link
8' POLY-CASTER II – 15.65" 108 link
Serial #s
2091–3849 Non PRO-CASTER Spreaders
2091–3849 Non PRO-CASTER Spreaders
3850–4996, 4809 – Higher, 5645 – Higher
Non PRO-CASTER Spreaders
0000–3849 Non PRO-CASTER Spreaders
4809 – Higher Non PRO-CASTER Spreaders
3850–4996, 4809 – Higher, 5645 – Higher
Non PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
3850–4996, 4809 – Higher, 5645 – Higher
Non PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders/8' POLY-CASTER II
ALL PRO-CASTER Spreaders
ALL POLY-CASTER II Spreaders
ALL POLY-CASTER II Spreaders
** The measurement is the overall width from the outside of one pin to the outside of the other.
Lit. No. 29032, Rev. 04
45
July 1, 2009
SPREADERS
SPREADER GEAR CASE REFERENCE CHART
A
E
D
A
F
Shoulder
E
C
D
B
F
Shoulder
B
C
Part Number
A
B
Input
Output
Shaft OD Shaft OD
MEASUREMENT
C
D
95756
5/8
3/4
95567
1
1-1/8
68803
65762
5/8
5/8
3/4
3/4
683742
1
1-1/8
14-3/8
1
1-1/8
1
1-1/8
68412
2
9171
68384
E
F
Comments
Input
Output
Output
Input
Shaft
Shaft
Shaft
Shaft
Length to Length to
Length
Length Shoulder Shoulder
POLY-CASTER™
5
POLY-CASTER II
18-3/8
4-7/32
SPEED-CASTER™ 2
3-3/16
3-3/16
Non PRO-CASTER™
2-5/8
Center Drive
2-5/8
2-5/8
S/N 202650 & higher
S/N 202389 – 202649
7-7/8
Reg Capacity
14-3/8
7-7/8
Reg Capacity/Hyd
2
8-3/8
Reg Capacity
7-7/8
High Capacity/Gas
3
1
1-1/8
18-3/8
684633
1
1-1/8
18-3/8
7-7/8
PRO-CASTER
94349
1
1-1/8
18-3/8
4-7/32
Direct Drive1
95567
1
1-1/8
18-3/8
4-7/32
Center Drive
High Capacity/Hyd
Stub shaft directly below input shaft
2
68374 and 68412 both use the 68732 gear case
3
68384 and 68463 both use 68733
1
Lit. No. 29032, Rev. 04
46
July 1, 2009
SPREADERS
Hopper and Tailgate Spreader Service Part Identification
Gear Boxes
Part
9171
65762
68384*
68803
68374
68412
95567
94349
95756
Description
RC & HC
Serial #s
0000–3849 Non PRO-CASTER™ Spreaders
202389–202649 SPEED-CASTER™ 2 Spreaders
3850–4808, 4809 – Higher Non PRO-CASTER Spreaders
202650 – Higher SPEED-CASTER 2 Spreaders
3850–4808, 4809 – Higher Non PRO-CASTER Spreaders
4809 – Higher Non PRO-CASTER Spreaders
0402 – Higher PRO-CASTER & POLY-CASTER™ II Spreaders
0001–0401 PRO-CASTER Spreaders (use 95400 coupler)
POLY-CASTER™ Spreaders
HC
RC
RC – Hydraulic
RC & HC
RC & HC
Spinner Shafts
Part
9191
9192
20319
20320
94407
94477
95294
94684
95420
95421
95795
95960
78067
Length (in)
23
35
27
39
19-1/4
31-1/4
24-1/4
20-5/8
28-1/2
40-1/2
16-1/2
32-1/2
35-7/8
Diameter (in)
3/4
3/4
1
1
1
1
1
1
1
1
3/4
13/16
3/4
Part
20321
94319
94513
Diameter (in)
14-1/2
14-1/2
14-1/2
Material
Black Steel
Stainless
Poly
94510
9-7/8
Poly
94884
94514
9196
20095
94512
9519
67090
94511
12
12
11-7/8
11-3/4
10-3/16 sq.
sq.
15-3/4
15-7/8
Poly
Poly
Black Steel
Stainless
Poly
Black Steel
Black Steel
Poly
P3047
9-7/8
Black Steel
P2024
94748-1
94749-1
95280
94511
94513
94424
9
18
18
18
15-1/2
14-1/2
15-1/2
Black Steel
Poly
Poly
Poly
Application
14" Chute – Non PRO-CASTER Spreaders (RC)
26" Chute – Non PRO-CASTER Spreaders (RC)
19" Chute – Non PRO-CASTER Spreaders (HC)
31" Chute – Non PRO-CASTER Spreaders (HC)
14" Offset Chute – Early PRO-CASTER Spreaders
26" Offset Chute – Early PRO-CASTER Spreaders
19" Offset Chute – Early PRO-CASTER Spreaders
Dual Hydraulic – Early PRO-CASTER Spreaders
14" Center Belt Drive Chute – PRO-CASTER Spreaders
26" Center Belt Drive Chute – PRO-CASTER Spreaders
Standard Chute – POLY-CASTER Spreaders
Extended Chute – POLY-CASTER Spreaders
POLY-CASTER II Spreaders
Spinners
Poly
Application
9107, 9108, 68920, 68921 – Non PRO-CASTER Spreaders (HC)
9107, 9108, 68920, 68921 – Non PRO-CASTER Spreaders (HC)
9107, 9108, 68920, 68921 – Non PRO-CASTER Spreaders (HC)
Low Profile Model 1000 and Low Profile Model 2000 Low Profile
Tailgate Spreaders
94357, 94474 – PRO-CASTER Spreaders
9031, 9032, 9189, 9194 – Non PRO-CASTER Spreaders (RC)
9031, 9032, 9189, 9194 – Non PRO-CASTER Spreaders (RC)
9031, 9032 – Non PRO-CASTER Spreaders (RC)
67274 – SPEED-CASTER™ Spreaders
67274 – SPEED-CASTER Spreaders
67130 – SPEED-CASTER 2 Spreaders
67130 – SPEED-CASTER 2 Spreaders
Low Profile Model 1000 (10003 – Higher) and
Low Profile Model 2000 (20364 – Higher) Tailgate Spreaders
Low Profile Model 110 Tailgate Spreaders (noncurrent)
UTS 696 MS (Frame of spinner assembly)
UTS 696 SS (Frame of spinner assembly)
UTS 696 (Spinner Kit)
Standard POLY-CASTER Spreaders
Extended POLY-CASTER Spreaders
94424 – POLY-CASTER II Spreaders
* Shaft must be drilled for use on hydraulically driven spreaders; PN 68384 replaces PN 68463
Lit. No. 29032, Rev. 04
47
July 1, 2009
SPREADERS
Hopper and Tailgate Spreader Service Part Identification
Spinner Shaft Bearings
Part
9193
Description
3/4" Pillow Block Bearing
w/Locking Collar
20322
1" Pillow Block Bearing
95488
1" Bearing Kit – Center
Belt Drive
94897
Spinner Bearing Kit –
Offset Direct Drive
Chutes
9189, 9031,
9194, 9032
9101, 9108,
68920, 68921
95424, 95425,
95426, 95427
94357, 94357-1,
94474, 94474-1,
94924, 94924-1,
94940, 94940-1,
95224, 95225
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC,
4809 – Higher RC Non PRO-CASTER™ Spreaders
2600–3849 HC, 3850–4808 HC, 4809 – Higher HC
Non PRO-CASTER Spreaders
0303 – Higher PRO-CASTER Spreaders
0126–0302 PRO-CASTER Spreaders
0144–0302 PRO-CASTER Dual-Hydraulic
Spreaders
Spinner Shaft Drive Components
Part
9187
20323
95489
Description
Sprocket – #40 x 24 Tooth
3/4" ID
Sprocket – #40 x 24 Tooth
1" ID
Center Belt Pulley Kit w/
Key
95400
Offset Chute Coupling Kit
95244
Hydraulic Coupling Kit
Part
Description
Chutes
9189, 9031,
9194, 9032
9101, 9108,
68920, 68921
95424, 95425,
95426, 95427
94357, 94357-1,
94474, 94474-1,
94924, 94924-1,
94940, 94940-1,
95224, 95225
95224, 95225
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC,
4809 – Higher RC Non PRO-CASTER Spreaders
2600–3849 HC, 3850–4808 HC, 4809 – Higher HC
Non PRO-CASTER Spreaders
0303 – Higher PRO-CASTER Spreaders
0126–0302 PRO-CASTER Spreaders
0144–0302 PRO-CASTER Dual-Hydraulic
Spreaders with Offset Chute
Conveyor Drive Gears
9163
20333
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC & HC,
Sprocket – 6T x 1.125" ID 4809 – Higher RC & HC Non PRO-CASTER Spreaders
0126 – Higher PRO-CASTER Spreaders
Sprocket – 8T x 1.13" ID 2600–3849 HC Non PRO-CASTER Spreaders
Drive Shaft Bearings
Part
9162
20337
94953
Description
2-Bolt Flange
Bearing – 1-1/8"
4-Bolt Flange
Bearing – 1-1/8"
Spreader Bearing Kit –
Conveyor
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC & HC,
4809 – Higher RC & HC Non PRO-CASTER Spreaders
2600–3849 HC Non PRO-CASTER Spreaders
0126 – Higher PRO-CASTER Spreaders
Conveyor Idler Shafts
Part
Size
9184
1" x 16"
20329
1.13" x 20.5"
68434
.998" x 20"
94351
.986" x 20.5"
Lit. No. 29032, Rev. 04
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC,
4809 – Higher RC Non PRO-CASTER Spreaders
2600–3849 HC Non PRO-CASTER Spreaders
3850–4808 HC, 4809 – Higher Non PRO-CASTER Spreaders
0126 – Higher PRO-CASTER Spreaders
48
July 1, 2009
SPREADERS
Hopper and Tailgate Spreader Service Part Identification
Idler Shaft Gears
Part
9183
20332
9163
Description
Idler Sprocket w/Bushing –
6T x 1.00" ID
Idler Sprocket w/Bushing –
8T x 1.13" ID
Sprocket w/Keyway & No
Bushing – 6T x 1.125" ID
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC & HC,
4809 – Higher RC & HC Non PRO-CASTER™ Spreaders
2600–3849 HC Non PRO-CASTER Spreaders
0126 – Higher PRO-CASTER Spreaders
Idler Shaft Bearings
Part
Description
9182K
Rod End – 1"
20331
94953
Rod End – 1-1/8"
Spreader Bearing Kit
Serial #s
0733–2599, 2600–3849 RC, 3850–4808 RC & HC,
4809 – Higher RC & HC Non PRO-CASTER Spreaders
2600–3849 HC Non PRO-CASTER Spreaders
0126 – Higher PRO-CASTER Spreaders
Part
94691
95418
Description
Engine to Clutch
Clutch to Spinner
Serial #s
All PRO-CASTER Spreaders (42370)
PRO-CASTER Spreaders w/Center Belt Drive (42300)
Part
94497
Description
8.5 HP Briggs & Stratton–to–10 HP Tecumseh
PRO-CASTER V-Belts
Engine Conversion Kit
No Longer Available
Gas Spreader Parts Kits
Part
94890
Description
Vehicle harness, control
and misc. hardware
94655
Serial #s
All PRO-CASTER Spreaders
All Non PRO-CASTER Spreaders
Repair Harnesses
Part
66427
67482
66426
67481
63726
Description
Spreader Harness – 11-Pin Repair End
Spreader Harness – 7-Pin Repair End
Vehicle Harness – 11-Pin Complete Harness
Vehicle Harness – 7-Pin Complete Harness
Vehicle Harness – 11-Pin Repair End
Serial #s
ALL PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
ALL Non PRO-CASTER Spreaders
ALL PRO-CASTER Spreaders
Part
95736
95737
Description
Chain-Belt Drive Conversion Kit
Chain-Belt Drive Conversion Kit
Part
28953
65516
29244
Description
Control Installation Kit for Variable Speed Control (28867)
Control Installation Kit for ON/OFF Spreader Control (9390) and PRO-CASTER Control
Kit converts old style round connector (PN 2157 / 2156) to new style 4-pin connector
Belt–Chain Drive Conversion Kit
Serial #s
All PRO-CASTER Belt-Driven Spreaders
Tailgate Spreader Wiring
Lit. No. 29032, Rev. 04
49
July 1, 2009
MISCELLANEOUS
Clevis Pin Identification
Dia. x Length
(in)
3/16 x 1
3/8 x 1
3/8 x 3-1/4
1/2 x 1-9/16
1/2 x 2-1/2
5/8 x 4-3/4
3/4 x 1-7/8
Pin
Kit
4491
26780
26219
27171K
28978
26656K
29037
67921
4289K
3/4 x 2-3/16
5523K
3/4 x 3-15/32
20639K
3/4 x 3-1/2
13/16 x 24-1/2
1 x 2-3/4
20988
27227
27241
1 x 3-5/16
6814
7904K
1 x 3-5/16 HT (Heat
Treated)
95720
29038
1 x 4-1/16
6816
7903K
1 x 4-3/4
1x6
1 x 6-1/4
1 x 6-13/16
1x8
1 x 8-11/16
1 x 15-13/16
1 x 17-9/16
1 to 3/4 x 2-1/2
(Stepped Pin)
1-1/8 x 10-1/8
1-1/4 x 3-1/16
1-1/4 x 4-9/16
1-1/4 x 5
1-1/4 x 5-5/8
1-1/4 x 6-21/32
1-1/2 x 4-3/8
1-1/2 x 7
1-1/2 x 8-1/2
1-1/2 x 9-3/4
5/8 x 2
5/8 x 3
1-1/8 x 9-1/2
1/2-13 x 2-1/2
1 x 2-13/16
1-8 x 9
3/4 x 3-1/4
22260
6817
6815
26833
27979
22259
26060
44028
Lit. No. 29032, Rev. 04
6990
7905K
6920K
27168K
27177K
5022
26164
5150
20790
5142
20789
5141
5458
7491
5149
50651
50653
50668
69669
69666
69667
69607
Application
Cable to valve block – Belt Drive Hydraulics
Stop link to cable – Minute Mount® 2 System
Clevis pin locates and retracts connecting pin – Minute Mount 2 System
Shoulder bolt and nut – trip spring assembly
Stop link to lift arm – Minute Mount 2 System
Hitch pin – Blade wing extension (XtremeV™)
Lift arm to headgear pin
Base angle pin – MC Blade (original), EZ-V® Blade, HS Blade, HT Series™,
L and M Blades
Base angle pin – MC Blade (original) "double ears" next to inner trip springs;
A-frame to plow gear – Personal Plow
Commercial EHP
Pivot pin – EZ-V Blade
Base angle pin – MC Blade (current), XBLADE™ & XtremeV Snowplow
Lift ram pin (lower only on Minute Mount 2 System; upper and lower on
original Minute Mount® System); Push Assembly to lower gear – original
Minute Mount system EZ-V Snowplow
Upper lift ram pin – Minute Mount 2 System
Angle ram pin at A-frame – noncommercial plows; base angle pin – MC
Blade (current) "double ears" next to inner trip springs & XLS™ Blades
Angle ram pin at blade – EZ-V, RD, HD, HT Series XtremeV & XLS Blades
Pivot pin – L, HS Blades; angle rams – EZ-V Blade with blade stop
Connecting pin w/handle – original Minute Mount System
Connecting pin – Minute Mount 2 System
Pivot pin – LD & SD Blades
Pivot pin – LD Blade
Pivot pin – M Blade
Pivot pin – XtremeV Blade
A-frame to lower gear pin – Minute Mount 2 System
Pivot pin – commercial tilt-hood headgear
A-frame to headgear – MC Blade w/Minute Mount 2 System
A-frame to lower gear – MC Blade; angle ram pin – commercial blades
Angle ram pin – MC Blade
Angle ram pin – MC Blade
Pivot pin – MC Blade
Hinge outer pin – Commercial Blade
Commercial connecting pin – original Minute Mount System
Hinge center pin – Commercial Blade
Pivot pin – HC Blade
XLS wing cylinder box end – rod end
XLS wing cylinder anchor end – base end; HT Series lift cylinder – base end
XLS pivot bolt w/nut
HT Series lift cylinder rod end bolt G5
HT Series base end pin angle ram shear pin
HT Series pivot bolt w/nut G5
HT Series A-frame to headgear
50
July 1, 2009
MISCELLANEOUS
"Dashed" Kit Numbers
Part
1213-1
1533-1
20703-1
21484-1
21500K-1
21696-1
21727-2
21874-1
21874-2
21874-3
22147-1
22150-1
22155-1
22160-1
22470-1
26018-1
26020-1
26047-2
26360-1
26361-1
26470-1
26470-2
26500-1
26705-1
26757-1
27560-1
26781-1
26781-2
26781-3
26812-1
27086-1
27255-1
27480-1
27600-1
27750-1
27968-1
27995-1
28027-1
28027-2
28350-1
28800-1
28801-1
28800-1
28860-1
29056-1
29070-1
29290-1
29294-1
Description
Homesteader™ Mount – Ford Explorer
Homesteader Mount – GM Trailblazer/Envoy
A-Frame – MC
EZ-V® Push Assembly
Motor Assembly
MC Conversion A-Frame w/Hardware
Pressure Control Breather
EZ-V A-Frame Assembly
EZ-V A-Frame Assembly
EZ-V A-Frame Assembly
Valve Manifold Assembly
Manifold Assembly
Hydraulic Unit 4000 psi
Hydraulic Unit 2500 psi
LD/RD/HD Rubber Deflector Kit
Mini Strobe Light
Mini Bar Light
Change
Redesigned to allow access to oil filter on V8 models
Redesigned rear brackets to accommodate '05 frame change
Added 2 chain tabs for lift chain to the end of A-frame
Added 1" to the width where drilling is required
New design multi-position motor with drain in cap
Added 2 chain tabs for lift chain to the end of A-frame
Design changed to reduce moisture ingression
Made bolt-together diagonal bracing a welded part
Made A-frame channel 1" wider
Updated hinge/weld on pivot tubes
Added SAE O-ring ports
Added SAE O-ring ports
Added SAE O-ring ports
Added SAE O-ring ports
Added hole to adapt for all L and M Blades
Changed lens and flash tube
Changed lens and lamp
Updated DRL information
Plug-In Harness HB-3 & HB-4-A, Long
Installation instructions changed to accommodate new models
Plug-In Harness HB-3 & HB-4-A, Short
Installation instructions changed to accommodate new models
Added 3-Port test adapter (PN 29294) and instructions for
Isolation Module Tester
3-Port Isolation Module
Isolation Module Tester
Literature change
Central Hydraulics Control Harness Kit
Changed the battery cable to 61169 (was 8274)
On-Truck Electrical Kit – Isolation Module
Added Adapter PN 29047 for 3-Port Isolation Module
Minute Mount® 2 Lift Arm (yellow)
Added heat-treated clevis pin and revised stop link
Minute Mount 2 Lift Arm (silver)
Added heat-treated clevis pin and revised stop link
Suction Filter
Literature Change
Suction Filter
Literature Change
Suction Filter
Literature Change
Plow Parka
Resized for Minute Mount 2 system w/INTENSIFIRE™ Headlamps
Bulk Motor Relay Kit
Changed to 5794K-1 relay and decreased quantity from 50 to 48
Minute Mount 2 MC Series A-Frame Kit
Moved A-frame and headgear attachment point to aid mounting
Plug-In Harness Kit HB-3 & HB-4-A, White Label Installation instructions changed to accommodate new models
XBLADE™ Rubber Deflector Kit
Modified to fit 7-1/2'–9' XBLADE snowplows
Updated A-frame length to accommodate new LD blade
Minute Mount 2 LD Headgear Kit
(1-1/2" longer)
Adapter Kit
Literature Change
Updated A-frame length to accommodate new LD blade
Minute Mount 2 LD A-Frame Kit
(1-1/2" longer)
Adapter Kit
Added 3-Port module to instructions
Reworked wiring to eliminate potential problems w/2007 GM
Adapter Kit
Vehicles
Lift Arm Service Kit
Added heat-treated clevis pin and revised stop link
Headlamp Kit (Pair) w/ Harness
Added 3rd screw for rear cover
Headlamp Kit (DS) w/o Harness
Added 3rd screw for rear cover
Headlamp Kit (PS) w/o Harness
Added 3rd screw for rear cover
Adapter Kit
Literature and Label Change
Adapter Kit
Changed instructions and wire locations
3-Port Module – DRL/Non-DRL
Module Change; Replaces 29060 & 29070
Harness Kit Diagnostic
Modified to work with XtremeV™ and XLS™ blades
Adapter Kit
Literature Change
Lit. No. 29032, Rev. 04
51
July 1, 2009
MISCELLANEOUS
"Dashed" Kit Numbers
Part
29400-1
29400-2
29760-1
307-1
3713-1
3713-2
31543-1
44281-1
44281-2
44282-1
44282-2
44283-1
44283-2
44327-1
44329-1
44354-1
44354-2
44475-1
44485-1
44495-1
44555-1
44556-1
44600-1
44610-1
44650-1
44675-1
44685-1
44695-1
44740-1
44742-1
44741-1
44743-1
44744-1
44775-1
44785-1
44791-1
44795-1
49258-1
49259-1
56831-1
5794K-1
63827-1
65605-1
65605-2
65605-3
65990-1
65990-2
66771-1
66772-1
66773-1
66775-1
66779-1
Description
Plug-In Harness Kit
Plug-In Harness Kit
3-Port Isolation Module – Blue Label
Shoe Spacer
Truck Mount – Jeep
Truck Mount – Jeep
Truck Mount – GM Colorado/Canyon
Back Drag Edge Kit
Back Drag Edge Kit
Back Drag Edge Kit
Back Drag Edge Kit
Back Drag Edge Kit
Back Drag Edge Kit
Reservoir Kit
Pump Kit
Plow Module
Plow Module
Blade Assembly – 7.5 blade
Blade Assembly – 8.5 blade
Blade Assembly – 9.5 blade
T-Frame
Push Assembly
Off-Truck Kit
Blade Wing Extension Kit
Off-Truck Kit
Blade Assembly – 7.5 XtremeV Blade MS
Blade Assembly – 8.5 XtremeV Blade MS
Blade Assembly – 9.5 XtremeV Blade MS
3/8" x 6" x 7-1/2' XtremeV Cutting Edge
1/2" x 6" x 7-1/2' XtremeV Cutting Edge
3/8" x 6" x 8-1/2' XtremeV Cutting Edge
1/2" x 6" x 8-1/2' XtremeV Cutting Edge
1/2" x 6" x 9-1/2' XtremeV Cutting Edge
Blade Assembly – 7.5 XtremeV Blade SS
Blade Assembly – 8.5 XtremeV Blade SS
Xtreme V Parts Bag
Blade Assembly – 9.5 XtremeV Blade SS
Seal Kit Valve
Seal Kit Valve
Hose 1/4" x 36" w/FJIC Ends (Obsolete)
Motor Relay Kit
Dodge 1500 Truck Mount
Spreader Battery Kit
Spreader Battery Kit
Spreader Battery Kit
Spreader Battery Kit Parts Bag
Spreader Battery Kit Parts Bag
Sec. Manifold Assembly w/Coils, Cart. & Covers
Sec. Manifold Assembly w/o Coils, Cart. & Covers
Primary Manifold Assembly w/Coils, Cart. & Covers
Primary Manifold Assembly w/o Coils, Cart. & Covers
EZ-V® Hydraulic Unit
Lit. No. 29032, Rev. 04
Change
Changed H11 connector to also fit Toyota's H11 connector
11-pin vehicle light harness with built-in 28027-2
New module covers DRL and non-DRL applications '08 Ford only
Increased diameter
Non "dash 1" kit does not fit 2002 models
Clamping plates removed from bolt bag
Added Extension Bracket Kit PN 40734
Added hole to match 4-piece cutting edge
Added washers to bolt bag
Added hole to match 4-piece cutting edge
Added washers to bolt bag
Added hole to match 4-piece cutting edge
Added washers to bolt bag
Literature change
Literature change
Service Part for both XtremeV™ & XLS™ Blades
Software Change
Changed to 4-piece cutting edge
Changed to 4-piece cutting edge
Changed to 4-piece cutting edge
Overlapping holes eliminated; angle braces revised
Hole added to side plates making it compatible with -1 T-Frame
Revised -1 T-Frame; push assy. & hardened steel pivot pin added
Redesigned wings
Revised -1 T-Frame; push assy. & hardened steel pivot pin added
Changed to 4-piece cutting edge
Changed to 4-piece cutting edge
Changed to 4-piece cutting edge
Revised to 4-Piece kit to improve anti-wear characteristics
Revised to 4-Piece kit to improve anti-wear characteristics
Revised to 4-Piece kit to improve anti-wear characteristics
Revised to 4-Piece kit to improve anti-wear characteristics
Revised to 4-Piece kit to improve anti-wear characteristics
Changed to 4-piece cutting edge
Changed to 4-piece cutting edge
Changed to 4-piece cutting edge
SV08-2004, CV08
SV08-30, 31 & 33
PN Consolidation; Literature & packaging change
Changed to heavier duty cycle
Added cross brace for trucks with factory-installed hitch
Added new starter relay kit
Added new 6-pin Tecumseh alternator harness
Update for Briggs & Stratton engine – charging wire
Support changes in 65605 kit
Added Briggs & Stratton wiring
Added SAE O-ring ports
Added SAE O-ring ports
Added SAE O-ring ports
Added SAE O-ring ports
Added SAE O-ring ports
52
July 1, 2009
MISCELLANEOUS
"Dashed" Kit Numbers
Part
66860-1
67040-1
67040-2
67487-1
67488-1
68940-1
68941-1
7146-1
7151-1
7151-2
7152-1
7154-1
7156-1
7159-1
7159-2
7162-1
7163-1
7170-1
7170-2
74700-3
7629K-3
7632K-2
7634K-1
7636K-1
7639K-1
8416-1
8430-1
8437-1
8446-1
8447-1
9027-1
9390-1
94582-1
94699-1
94700-1
94700-2
94700-3
94701-1
94701-2
94703-1
94703-2
94704-1
94704-2
94706-1
94706-2
94706-3
94707-1
94707-2
94708-1
94708-2
94709-1
Description
Hopper Control Assembly
Dodge Tailgate Spreader Mount
Dodge Tailgate Spreader Mount
Dodge Tailgate Spreader Mount Rear Brkt – DS
Dodge Tailgate Spreader Mount Rear Brkt – PS
Engine Mount
Mild Steel Engine Base
Minute Mount® Pec. Attach. Kit – Topkick/Kodiak T50
Minute Mount Peculiar Attachment Kit – Internat'l
Minute Mount Peculiar Attachment Kit – Internat'l
Minute Mount Pec. Attachment Kit – F700/F800
Minute Mount Pec. Attach. Kit – Topkick/Kodiak T40
Minute Mount Pec. Attachment Kit – Univ. Comm.
Minute Mount Peculiar Attachment Kit – Ford
Minute Mount Peculiar Attachment Kit – Ford
Minute Mount Peculiar Attachment Kit – Mitsu.
Minute Mount Peculiar Attachment Kit – Wrangler
Minute Mount Peculiar Attachment Kit – Ram
Minute Mount Peculiar Attachment Kit – Ram
Hopper Spreader
Relief Valve Repair Kit
O-Ring/Backup Ring Kit
Valve SV08-2004 w/Jam Nut
Valve SV08-2004 w/Jam Nut
Coil w/Spade Terminal
Common Light Kit – 9-Pin
Common Light Kit – 9-Pin Commercial
Plug-In Harness Kit HB-3 & HB-4-A, Lt. Green
Minute Mount MC A-Frame Kit
MC Conversion Attachment Kit
Variable Speed Control (PWM)
ON/OFF Control (Boxed)
Baffle Hood
Engine Cover
PRO-CASTER™ Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
Lit. No. 29032, Rev. 04
Change
Added new ground harness
Revised to fit redesigned vehicle exhaust
Revised to fit redesigned vehicle rear spring shackle
Revised to fit redesigned vehicle rear spring shackle
Revised to fit redesigned vehicle rear spring shackle
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Revised for Minute Mount® 2 MC headgear
Added additional notches for brake line clearance
Increased skid bar clearance for Minute Mount 2 MC headgear
Increased skid bar clearance for Minute Mount 2 MC headgear
Increased skid bar clearance for Minute Mount 2 MC headgear
Increased skid bar clearance for Minute Mount 2 MC headgear
Added notch in DS pushplate to accommodate pitman arm
Adapted pushplates to accommodate change in diesel engine
Redesigned trailing arm (recalled 7162 trailing arms)
Revised to accommodate 1999 frame bracket (replaced spacer)
Non "dash 1" kit does not fit diesel vehicles
Non "dash 2" kit does not fit Laramie package
Change to Briggs & Stratton engine
Literature change
Added XLS™ hydraulic parts
Literature change
Literature change
Literature change
Extended length of wire harness for Insta-Act® hydraulic unit
Extended length of wire harness for Insta-Act hydraulic unit
Wiring changes for 2004 Colorado/Canyon
Added 2 chain tabs for lift chain to the end of A-frame
Added 2 chain tabs for lift chain to the end of A-frame
Added 66413 adapter harness to back fit 3-wire harness
Added 66413 adapter harness to back fit 3-wire harness
Changed for Briggs & Stratton engine
Changed for Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Changed for Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Changed for Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Literature change
Converted to in-line chute (made offset chute obsolete)
53
July 1, 2009
MISCELLANEOUS
"Dashed" Kit Numbers
Part
94709-2
94709-3
94710-1
94710-2
94711-1
94712-1
94712-2
94712-3
94713-1
94714-1
94715-1
94716-1
94716-2
94717-1
94718-1
94718-2
94718-3
94719-1
94719-2
94720-1
94721-1
94721-2
94722-1
94722-2
94723-1
94746-1
94747-1
94748-1
94749-1
94918-1
94940-1
94952-1
95350-1
95350-2
95350-3
95351-1
95351-2
95352-1
95353-1
95353-2
95353-3
95354-1
95354-2
95355-1
95424-1
95425-1
95426-1
95427-1
95755-1
95757-1
95770-1
Description
PRO-CASTER™ Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
UTS 696 Stainless Steel Spinner Frame
UTS 696 Mild Steel Spinner Frame
UTS 696 Mild Steel Spinner Assembly
UTS 696 Stainless Steel Spinner Assembly
Stainless Steel Engine Base
PRO-CASTER Hopper Spreader
Engine Cover
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
PRO-CASTER Hopper Spreader
Chute Assembly
Chute Assembly
Chute Assembly
Chute Assembly
POLY-CASTER™ Motor, 1/2 HP
Conveyor Belt
Belt Guard–Side
Lit. No. 29032, Rev. 04
Change
Changed to chain drive
Changed to Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Changed to Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Changed to Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Changed to octagonal-shaped frame
Changed to octagonal-shaped frame
Changed to octagonal-shaped frame
Changed to octagonal-shaped frame
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Baffle change for Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Changed to Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Changed to Briggs & Stratton engine
Converted to in-line chute (made offset chute obsolete)
Changed to chain drive
Converted to in-line chute (made offset chute obsolete)
Removed output guards (no longer needed)
Removed output guards (no longer needed)
Removed output guards (no longer needed)
Removed output guards (no longer needed)
Changed motor to Canimex motor (SS)
Revised to 4 cleats
Revised to extend the whole length of the sill
54
July 1, 2009
MISCELLANEOUS
"Dashed" Kit Numbers
Part
95796-1
95847-1
95931-1
95932-1
96001-1
96380-1
9825-1
9828-1
9828-2
9828-3
9828-4
9835-1
9840-1
9840-2
Description
Pulley, 4.5" x .750 Bore
Top Screen
Poly Hopper Lid (DS)
Poly Hopper Lid (PS)
Poly Hopper Spreader
Top Screen Brace
Insta-Act® LD Hydraulic Unit (2500 psi)
Insta-Act EZ-V® Hydraulic Unit
Insta-Act EZ-V Hydraulic Unit
Insta-Act EZ-V Hydraulic Unit
Insta-Act EZ-V Hydraulic Unit
Insta-Act MC Hydraulic Unit (3500 psi)
Insta-Act RD/HD Hydraulic Unit (4000 psi)
Insta-Act RD/HD Hydraulic Unit (4000 psi)
Lit. No. 29032, Rev. 04
Change
Changed material to steel
Changed to finer mesh
Revised to include molded handles
Revised to include molded handles
Without spinner assembly
Threaded holes to accept wing bolts
Added low-friction rams, SAE porting, JIC hoses and fittings
Added new seals for double-acting rams
Added low-friction lift ram
Added low-friction rams, SAE porting, JIC hoses and fittings
Removed control
Added low-friction lift ram
Added low-friction lift ram
Added low-friction rams, SAE porting, JIC hoses and fittings
55
July 1, 2009
Fisher Engineering
Rockland, ME 04841
www.fisherplows.com
A SUBSIDIARY OF DOUGLAS DYNAMICS, L.L.C.
Copyright © 2009 Douglas Dynamics. L.L.C. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any
printed, mechanical, electronic, film or other distribution and storage media, without the written consent of Fisher Engineering. Authorization
to photocopy items for internal or personal use by Fisher Engineering outlets or snowplow/spreader owner is granted.
Fisher Engineering reserves the right under its product improvement policy to change construction or design details and furnish equipment
when so altered without reference to illustrations or specifications used. Fisher Engineering or the vehicle manufacturer may require or
recommend optional equipment for snow removal/spreaders. Do not exceed vehicle ratings with a snowplow/spreader. Fisher Engineering
offers a limited warranty for all snowplows/spreaders and accessories. See separately printed page for this important information. The following
are registered (®) or unregistered (™) trademarks of Douglas Dynamics, L.L.C.: EZ-V®, FISHER®, Fish-Stik ®, Homesteader™, HT Series™,
Insta-Act ®, INTENSIFIRE™, Minute Mount ®, Minute Mount ® 2, POLY-CASTER™, POLY-CASTER™ II, PRO-CASTER™, ProTube™, SnoFoil ®,
SPEED-CASTER™, SPEED-CASTER™ 2, SWING AWAY®, XBLADE™, XLS™, XtremeV™.
Printed in U.S.A.
Lit. No. 29032, Rev. 04
July 1, 2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement