General Music RP100 BALDWIN Service manual

Index
2
3
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Opening Instructions & Keyboard disassembling
RP100-150 Initial Check, Autotest Procedure, Updating Procedure
RP200 Initial Check, Autotest Procedure, Updating Procedure
RP100-150 Block Diagram
RP200 Block Diagram
RP100 - Power Amplifier & Supply, Pedals, Phones, Outputs Boards
RP150 - Power Amplifier & Supply, Pedals, Phones, Outputs Boards
RP200 - Power Amplifier & Supply, Pedals, Mixer & Phones Aplifier, Phones, Outputs Boards
Keyboard Interface & Contacts Boards
RP100-150 Controls Panel & Display Boards
RP200 Controls Panel & Display Boards
RP100-150 Cpu & Sound Generator Board
Timing Table & 310603 Board Layout
RP200 Cpu & Sound Generator Board Part 1 of 2
RP200 Cpu & Sound Generator Board Part 2 of 2
RP100 and RP150 Spare Part List
RP200 Spare Part List
Warnings
SERVICE MANUAL
Notice
Service must be carried out by qualified personnel only.Any tampering carried out by unqualified personnel during the guarantee period
will forfeit the right to guarantee.
For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching on again.
To improve the device's specifications, the schematic diagrams may be subject to change without prior notice.
All components marked by this symbol have special safety characteristics, when replacing any of these components use only
manufacturer's specified parts.
The (µ) micro symbol of capacitance value is substituted by U.
The (Ω) omega symbol of resistance value is substituted by E.
The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified.
All resistors are 1/8Ω unless otherwise specified.
All switches shown in the "OFF" position. All DC voltages measured to ground with a voltmeter 20KOhm/V.
Soldering point.
Supply voltage.
Logic supply ground.
Male connector.
Test point.
Analog supply ground.
Female connector.
M/F faston connector.
Flag joined with one or more flags
Chassis ground.
with the same signal name inscribed.
Earth ground.
ATTENTION
Observe precautions when handling electrostatic sensitive devices.
Address
L CODE: 270212M
GENERALMUSIC S.p.A. Sales Division: 47842 S.Giovanni in Marignano (RN) ITALY - Via delle Rose, 12 - tel. 0541/959511 - fax 0541/957404
GENERALMUSIC on the NET: http://www.generalmusic.com
1J
1) TO REMOVE THE COVER UNSCREW THE 4 SCREWS ON THE REAR, PULL THE COVER TOWARDS YOU AND LIFT IT UP.
2) TO REMOVE THE CONTROL PANEL UNSCREW THE SCREWS AT EACH END AND THE SCREWS THAT ANCHOR
3) TO REMOVE THE KEYBOARD TP21 UNSCREW THE 11 SCREWS UNDER THE KEYBOARD.
THE CONTROL PANEL SUPPORTS TO THE CHASSIS.
RP100
RP100
RP100
4) TO REMOVE A KEY INSERT A SCREWDRIVER OR OTHER SIMILAR OBJECT IN THE SPLIT AT THE KEY BACK, APPLY A LIGHT PRESSURE AND PUSH IN THE DIRECTION SHOWN.
NOTE: BEFORE YOU REMOVE A NATURAL KEY YOU MUST REMOVE THE KEYBOARD, IF YOU REMOVE A SHARP KEY THIS OPERATION IS NOT NECESSARY
1) TO REMOVE THE COVER UNSCREW THE 4 SCREWS ON THE REAR, PULL THE COVER TOWARDS YOU AND LIFT IT UP.
RP150
RP200
TP21
REMOVE THE KEY RETURN SPRING.
UNLOCK THE KEY APPLING NOT MUCH STRENGTH.
NOTE: TO REMOVE A SHARP KEY BEFORE YOU MUST REMOVE THE NEAR NATURAL KEYS.
TP10
J2
DRWG. BOCCATO
DWG#500870
PCB#
GENERALMUSIC S.p.A. ITALY
CKD
1/1
DISK: PART:
APP.
REV:26/07/99
RP-100-150-200
Opening Instructions
& Keyboard disassembling
ALL RIGHTS ARE RESERVED, NO COPIES
OR REPRODUCE THIS DOCUMENT WITHOUT
WRITTEN CONSENT BY GENERALMUSIC.
RP100-150 INITIAL CHECK
Operation Descriptions
Re-set the frequency at 1KHz and check HEADPHONES and AUX outputs with the
oscilloscope inserting a stereo jack in the left phones socket (speakers will go be
silent) and two mono jack in the AUX OUT sockets and set volume to its maximum.
Display
The procedures that follow must be executed subsequently in the order specified.
Before turn on the instrument check the jumpers setting on CPU & SOUND
GENERATOR BOARD corresponds at the model accordingly to the following table:
|
|
MODEL
RP100
RP100
RP150
RP150
RP90
RP90
|
* BALDWIN * |
|PIANOVELLE RP100|
GEM
BALDWIN
GEM
BALDWIN
GEM
BALDWIN
J4
1-2
1-2
1-2
1-2
1-2
1-2
J5
1-2
1-2
1-2
1-2
1-2
1-2
J3
1-2
1-2
1-2
1-2
2-3
2-3
J6
1-2
1-2
2-3
2-3
1-2
1-2
J2
1-2
2-3
1-2
2-3
1-2 ** v.2.00 or greater
2-3 ** v.2.00 or greater
Remove the secondary fuses F1, F2, F3, located on POWER AMPLIFIER & SUPPLY
BOARD; turn on the instrument and verify the supply AC voltages:
(CN5) between pin1 and pin3 = 10±0,5Vac
(CN9) between pin1 and pin2 = 16±0,8Vac
(CN9) between pin1 and pin3 = 16±0,8Vac
(CN9) between pin2 and pin3 = 32±1,6Vac
* REALPIANO * |
RP100
|
Set the VOLUME to minimum.
|
|
* REALPIANO * |
RP150
|
|
* BALDWIN * |
|PIANOVELLE RP150|
* REALPIANO * |
RP90
|
|
* BALDWIN * |
|PIANOVELLE RP90 |
|INTERNAL PRESET|
| GRAND PIANO
|
RP100-150 AUTOTEST PROCEDURE
Operation Descriptions
Set the default display contrast in the ±6 range by pressing the DATA + or - buttons.
The instrument show the date, time and release version of the software loaded in
flash memory.
The instrument asks if you want to update it, press GRAND PIANO to skip, the
appropriate procedure to update the software is explained further.
The instrument performs the flash memory data checksum and display it in
hexadecimal value.
NOTE: the BT (boot) value must be 95C4 for ver.2.00, if it does not correspond you
can not update software thru serial port but only with Update Software Board.
The instrument performs the RAM memory test showing the address checked.
The LCD display test shows two rows of sixteen dark spaces.
Check that all leds are lighting.
Check the VOLUMES ranges from 0 to 127.
Check all buttons (except GRAND PIANO) pressing their one at a time and checking
that corresponding led lights, pressing PAGE UP and DOWN buttons the display shows
"U" and "D", pressing DATA + and - buttons the display shows "+" and "-", pressing
BALANCE < and > buttons the display shows an "X" in 1 and 2 digits, pressing
TOUCH, STORE and REC/CONTROL buttons the display shows an "X" in 3, 4 and 5
digits respectively.
Check the SOFT and SUSTAIN pedals, pressing each one the value change from 0
(released) to 127 (pressed), for RP100 the DAMPER pedal operation is similar, for
RP150 the DAMPER pedal varying its value continuosly from 0 (released) to nearly
127 (pressed).
Check the MIDI I/O connecting the MIDI OUT and MIDI IN sockets by a MIDI cable.
Check COMPUTER I/O shorting pin 3 and pin 5 on the COMPUTER socket, check with
the oscilloscope a 4Vpp (1Mhz) signal on pin 1, set volume to half stroke.
The instrument generates a 1KHz sinusoidal signal in both audio channels. VOLUME
fader controls the amplitude of signal and TRANSPOSE b and # buttons controls the
frequency from 10Hz to 2756Hz.
Autotest is over, turn off the instrument.
Display
|
|
RP98
AUTOTEST
|
|
|CONTRAST = #
|
|
|
| mmm dd yyyy
|
|hh:mm:ss V #.##|
|EPROM to FLASH |
|push REC to prog|
|Wait
*
|
|Eprom Checksum |
|cks BT
PR ALL|
| #### #### ####|
|RAM MEMORY CHECK|
|addr 23BFFF
OK|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|--- LED TEST ---|
|Are all leds on?|
| |Button test
|
| |Vol:0
12345 |
|U|Button test +|
|D|Vol:127 XXXXX-|
|Soft
| 0
Sust
0
Damp|
0|
|TEST MIDI IN/OUT|
|LOOP DETECTED OK|
|TST COMPUTER I/O|
|LOOP DETECTED OK|
| SINUS. SWEEP |
|Freq.
1000 Hz|
|TEST END: SWITCH|
|POWER TO RESTART|
RP100-150 O.S. UPDATING PROCEDURE up to ver. 2.00 with Updating Software Board (751180)
Start with the instrument in AUTOTEST mode as described above and press GRAND
PIANO 2 times until the display shows the software version loaded in flash memory.
Press GRAND PIANO to skip this procedure.
The instrument performs the flash memory data checksum and display it in
hexadecimal value.
Turn on the instrument and the appropriate welcome message appears on the display.
The instrument starts in AUTOTEST mode turning on the instrument while pressing
down the "GRAND PIANO" button (pressing PRESET instead GRAND PIANO the
procedure starts from LCD display test).
NOTE: Each time you press the "GRAND PIANO" button the autotest procedure
proceeds to the next step.
Apply a sinusoidal signal of 0.730Vpp at 1KHz with a generator to the AUX IN left and
right sockets and verify the signal output:
AUX output = 1.35±0.07Vpp
Operation Descriptions
|
|
Turn off the instrument, and put the fuses back on its holders.
A few seconds later the led GRAND PIANO light.
Check the supply DC voltages on CPU & SOUND GENERATOR BOARD:
(CN8) between pin9 and pin7 = +5±0,25Vdc
(CN8) between pin1 and pin4 = +12±0,6Vdc
(CN8) between pin1 and pin5 = -12±0,6Vdc
Now verify the following level of signals:
Phones output without load = 17±1.7Vpp
AUX output = 1.35±0.14Vpp
Display
| mmm dd yyyy
|
|hh:mm:ss V #.##|
|EPROM to FLASH |
|push REC to prog|
|Wait
*
|
|Eprom Checksum |
|cks BT
PR ALL|
| #### #### ####|
Compare the software version and checksum with the value imprinted onto the
EPROM, if one of these does not match, the system must be upgraded, proceed to the
next step.
Turn off the instrument.
Insert the EPROM BOARD (where the operating system is stored) in the CN3
connector located on CPU & SOUND GENERATOR BOARD.
Start with the instrument in AUTOTEST mode as described above and press GRAND
PIANO 3 times.
When the display shows this message press REC.
The instrument erases the previous data in flash memory. After which the instrument
displays the amount of memory programming and finally the operation successful. If
the programming fails check the EPROM BOARD connection and repeat this procedure
from start.
The instrument performs the eprom memory data checksum and displays it in
hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
matches the EPROM is good.
|EPROM to FLASH |
|push REC to prog|
|EPROM to FLASH |
|erasing
|
|EPROM to FLASH |
|prog: 1024/1024K|
|Wait
*
|
|Eprom Checksum |
|cks BT
PR ALL|
| #### #### ####|
Turn off the instrument and disconnect the EPROM BOARD.
Start with the instrument in AUTOTEST mode as described above and press GRAND
PIANO 2 times until the display show the new software version loaded in flash
memory.
Press GRAND PIANO to skip this procedure.
The instrument performs the flash memory data checksum and displays it in
hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
matches the procedure has been executed succesfully.
| mmm dd yyyy
|
|hh:mm:ss V #.##|
|EPROM to FLASH |
|push REC to prog|
|Wait
*
|
|Eprom Checksum |
|cks BT
PR ALL|
| #### #### ####|
The procedure proceed as described in AUTOTEST section, if you do not want to check
the rest of the instrument simply turn off it.
RP100-150 O.S. UPDATING PROCEDURE from Serial Port (COMPUTER) ver. 2.xx or greater
Operation Descriptions
Display
NOTE: This procedure is valid only if the software version installed on the piano is the
2.00 or greater.
Some additional tips and advices are included in the Flashblaster Firmware Update
Disk. The disk containing the Fblaster program can also be downloaded by internet at
generalmusic web site (www.generalmusic.com) or required at
[email protected]
Connect the serial cable between the COMPUTER of the piano and the RS232 COM
port of the computer (PC-Ibm or compatible).
Insert the disk in the drive A (or whatever your 3.5" drive is assigned to), open the
contents of drive A and double click on the fblaster.exe file.
From the OPTIONS/SETTINGS menu, make sure that the TEST AND PROGRAM choice
is selected. This is very important.
3J
Turn on the piano, while holding down the REC button until the display shows:
|READY TO UPDATE |
|
|
Click with the mouse on the GO! button or, from the ACTION menu, select EXECUTE
(ALT+A, E). The piano display appears as follows:
|TESTING...
|n1/n2 PACKETS
|
|
At the end of the test the following display appears:
|
TEST OK
|
|ERASING...
|
|
|
|
|
You are now erasing the old operating system from FLASH memory. When the system
is erased, the following display appears as your new operating system is installed into
Flash Memory:
|UPDATING...
|n1/n2 PACKETS
|
|
When the entire update procedure is completed, the following display appears:
|UPDATE_OK:SWITCH|
|POWER TO RESTART|
After a short time, the following display appears:
The update has now been successfully completed. Turn off the power switch on the
piano, and turn it back on again to use your updated instrument.
RP100-150 Some Repairing Tips
Operation Descriptions
Display
This message could be appear if an error occur on the communication channel.
Possible solutions:
1) inconsistent data received on MIDI or COMPUTER input socket, check the ratings of
the device connected to the piano.
2) if the error persist, try to replace Outputs Board first and CPU board second.
|MIDI SCI error
|
This message could be appear if an error occur on the communication channel.
Possible solutions:
1) verify all the connections between Keyboard Interface Board and the CPU board.
2) if the error persist, try to replace Keyboard Interface Board first and CPU board
second.
|VALIS SCI error |
|
|
This message could be appear if an error occur on the communication between CPU
and DISP3 chips.
Possible solutions:
1) verify all the tracks, solders and components between CPU and DISP3 chips as
shown in schematics.
2) if the error persist, replace the CPU board and send back to generalmusic the failed
CPU board.
|
|
RP200 INITIAL CHECK
Operation Descriptions
The procedures that follow must be executed subsequently in the order specified.
Before turn on the instrument check the jumpers setting on CPU & SOUND
GENERATOR BOARD corresponds at the model accordingly to the following table:
MODEL
RP200 GEM
RP200 BALDWIN
GRP300 GEM
GRP300 BALDWIN
J4
1-2
1-2
1-2
1-2
J5
1-2
1-2
1-2
1-2
J3
1-2
1-2
1-2
1-2
J6
1-2
1-2
2-3
2-3
J2
1-2
2-3
1-2 ** v.2.00 or greater
2-3 ** v.2.00 or greater
Remove the secondary fuses F1, F2, F3, located on POWER AMPLIFIER & SUPPLY
BOARD; turn on the instrument and verify the supply AC voltages:
(CN6) between pin1 and pin2 = 27,5±1,5Vac
(CN6) between pin1 and pin3 = 27,5±1,5Vac
(CN6) between pin2 and pin3 = 55±3Vac
(CN12) between pin1 and pin2 = 16±0,8Vac
(CN12) between pin1 and pin3 = 16±0,8Vac
(CN12) between pin2 and pin3 = 32±1,6Vac
|
|
|
RP200
REALPIANO
GEM
|
|
|
|
|
|
PIANOVELLE
RP200
BALDWIN
|
|
|
|
|
|
GRP300
REALPIANO
GEM
|
|
|
|
|
|
PIANOVELLE
GRP300
BALDWIN
|
|
|
Turn off the instrument, and put the fuses back on its holders.
Turn on the instrument and the appropriate welcome message appears on the display.
A few seconds later the led GRAND PIANO light.
Check the supply DC voltages on CPU & SOUND GENERATOR BOARD:
(CN8) between pin9 and pin7 = +5±0,25Vdc
(CN8) between pin1 and pin4 = +12±0,6Vdc
(CN8) between pin1 and pin5 = -12±0,6Vdc
|INTERNAL PRESET|
| GRAND PIANO
|
|GR.PIANO sel.:1|
RP200 AUTOTEST PROCEDURE
|Disp Failure
|
|
|
Operation Descriptions
The instrument starts in AUTOTEST mode turning on the instrument while pressing
down the "GRAND PIANO" button (pressing PRESET instead GRAND PIANO the
procedure starts from LCD display test).
NOTE: Each time you press the "GRAND PIANO" button the autotest procedure
proceeds to the next step.
Set the default display contrast in the ±6 range by pressing the DATA + or - buttons.
The instrument shows the date, time and release version of the software loaded in
flash memory.
The instrument asks if you want to update it, press GRAND PIANO to skip, the
appropriate procedure to update the software is explained further.
The instrument performs the flash memory data checksum and display it in
hexadecimal value.
NOTE: the BT (boot) value must be EAAB for ver.2.00, if it does not correspond you
can not update software thru serial port but only with Update Software Board see
more further.
The instrument performs the "LIBRARY" Rom memory data checksum and display it in
hexadecimal value.
The instrument performs the RAM memory test showing the address checked.
The LCD display test fades from light to dark and viceversa.
Check that all leds are lighting.
J4
Display
Display
|
|
|
RP98
AUTOTEST
|
|
|
|CONTRAST = #
|
|
|
|
|
| mmm dd yyyy
|
|hh:mm:ss V #.##|
|
|
|EPROM to FLASH |
|push REC to prog|
|
|
|Wait
*
|
|Eprom Checksum |
|
|
|cks BT
PR ALL|
| #### #### ####|
|
|
|Wait
*
|
|Library Checksum|
|
|
|Wait
ok! |
|Checksum:
A021|
|
|
|RAM MEMORY CHECK|
|addr 23BFFF
OK|
|
|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚|
|--- LED TEST ---|
|Are all leds on?|
|
|
Check the VOLUMES ranges from 0 to 127.
Check all buttons (except GRAND PIANO) pressing their one at a time and checking
that corresponding led lights, pressing PAGE UP and DOWN buttons the display shows
"U" and "D", pressing DATA + and - buttons the display shows "+" and "-", pressing
MASTER EQ and DSP buttons the display shows an "X" in 1 and 2 digits, pressing UP,
LEFT, DOWN and RIGHT buttons the display shows an "X" in 3, 4, 5 and 6 digits
respectively.
Check the SOFT and SUSTAIN pedals, pressing each one the value change from 0
(released) to 127 (pressed), the DAMPER pedal varying its value continuosly from 0
(released) to nearly 127 (pressed).
Check the MIDI I/O connecting the MIDI OUT and MIDI IN sockets by a MIDI cable.
Check COMPUTER I/O shorting pin 3 and pin 5 on the COMPUTER socket, check with
the oscilloscope a 4Vpp (1Mhz) signal on pin 1, set volume to half stroke.
The instrument generates a 1KHz sinusoidal signal in both audio channels reading
data from 104043 ROM. VOLUME controls the amplitude of signal and TRANSPOSE b
and # buttons controls the frequency from 10Hz to 2756Hz.
| |Button test
|
| |Vol:0
|
|
123456|
|U|Button test +|
|D|Vol:127
-|
|
XXXXXX|
|Soft Sust Damp|
| 0
0
0|
|
|
|TEST MIDI IN/OUT|
|LOOP DETECTED OK|
|
|
|TST COMPUTER I/O|
|LOOP DETECTED OK|
|
|
| SINUS. SWEEP |
|Freq.
1000 Hz|
|
|
Re-set the frequency at 1KHz and check HEADPHONES and AUX outputs with the
oscilloscope inserting a stereo jack in the left phones socket (speakers will go be
silent) and two mono jack in the AUX OUT sockets and set volume to its maximum.
Now verify the following level of signals:
Phones output without load = 5,7±1.1Vpp
AUX output = 0,8±0,16Vpp
Turn off the instrument and disconnect the EPROM BOARD.
Start with the instrument in AUTOTEST mode as described above and press GRAND
PIANO 2 times until the display show the new software version loaded in flash
memory.
Press GRAND PIANO to skip this procedure.
The instrument performs the flash memory data checksum and display it in
hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
matches the procedure has been executed succesfully.
RP200 O.S. UPDATING PROCEDURE from Serial Port (COMPUTER) ver. 2.xx or greater
Operation Descriptions
Apply a sinusoidal signal of 0.730Vpp at 1KHz with a generator to the AUX IN left and
right sockets and verify the signal output:
AUX output = 1,35±0.07Vpp
Insert the disk in the drive A (or whatever your 3.5" drive is assigned to), open the
contents of drive A and double click on the fblaster.exe file.
Autotest is over, turn off the instrument.
RP200 O.S. UPDATING PROCEDURE up to ver. 2.00 with Updating Software Board (751180)
Operation Descriptions
Start with the instrument in AUTOTEST mode as described above and press GRAND
PIANO 2 times until the display show the software version loaded in flash memory.
Press GRAND PIANO to skip this procedure.
The instrument performs the flash memory data checksum and displays it in
hexadecimal value.
Display
| mmm dd yyyy
|
|hh:mm:ss V #.##|
|
|
|EPROM to FLASH |
|push REC to prog|
|
|
|Wait
*
|
|Eprom Checksum |
|
|
|cks BT
PR ALL|
| #### #### ####|
|
|
Compare the software version and checksum with the value imprinted onto the
EPROM, if one of these does not match, the system must be upgraded, proceed to the
next step.
Turn off the instrument.
Insert the EPROM BOARD (where the operating system is stored) in the CN3
connector located on CPU & SOUND GENERATOR BOARD.
Start with the instrument in AUTOTEST mode as described above and press GRAND
PIANO 3 times.
When the display shows this message press REC.
The instrument erases the previous data in flash memory. After which the instrument
displays the amount of memory programming and finally the operation successful. If
the programming fails check the EPROM BOARD connection and repeat this procedure
from start.
The instrument performs the eprom memory data checksum and display it in
hexadecimal value, compare this value with the value imprinted onto the EPROM: if it
matches the EPROM is good.
Display
NOTE: This procedure is valid only if the software version installed on the piano is the
2.00 or greater.
Some additional tips and advices are included in the Flashblaster Firmware Update
Disk. The disk containing the Fblaster program can also be downloaded by internet at
generalmusic web site (www.generalmusic.com) or required at
[email protected]
Connect the serial cable between the COMPUTER of the piano and the RS232 COM
port of the computer (PC-Ibm or compatible).
|TONE ON 104023 |
|
|
|
|
|TEST END: SWITCH|
|POWER TO RESTART|
|
|
|cks BT
PR ALL|
| #### #### ####|
|
|
The procedure proceed as described in AUTOTEST section, if you do not want to check
the rest of the instrument simply turn off it.
Set the VOLUME to minimum.
The instrument generates a tone signal in both audio channels reading data from
104023 ROM.
| mmm dd yyyy
|
|hh:mm:ss V #.##|
|
|
|EPROM to FLASH |
|push REC to prog|
|
|
|Wait
*
|
|Eprom Checksum |
|
|
From the OPTIONS/SETTINGS menu, make sure that the TEST AND PROGRAM choice
is selected. This is very important.
|READY TO UPDATE
|
|
|TESTING...
|n1/n2 PACKETS
|
|
TEST OK
|
|
|ERASING...
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You are now erasing the old operating system from FLASH memory. When the system
is erased, the following display appears as your new operating system is installed into
Flash Memory:
|UPDATING...
|n1/n2 PACKETS
|
|
|
|
When the entire update procedure is completed, the following display appears:
|UPDATE_OK:SWITCH|
|POWER TO RESTART|
|
|
Turn on the piano, while holding down the REC button until the display shows:
Click with the mouse on the GO! button or, from the ACTION menu, select EXECUTE
(ALT+A, E). The piano display appears as follows:
At the end of the test the following display appears:
After a short time, the following display appears:
The update has now been successfully completed. Turn off the power switch on the
piano, and turn it back on again to use your updated instrument.
RP200 Some Repairing Tips
Operation Descriptions
|EPROM to FLASH |
|push REC to prog|
|
|
|EPROM to FLASH |
|erasing
|
|
|
|EPROM to FLASH |
|prog: 1024/1024K|
|
|
|Wait
*
|
|Eprom Checksum |
|
|
|cks BT
PR ALL|
| #### #### ####|
|
|
Display
This message could be appear if an error occur on the communication channel.
Possible solutions:
1) inconsistent data received on MIDI or COMPUTER input socket, check the ratings of
the device connected to the piano.
2) if the error persist, try to replace Outputs Board first and CPU board second.
|MIDI SCI error
|
|
This message could be appear if an error occur on the communication channel.
Possible solutions:
1) verify all the connections between Keyboard Interface Board and the CPU board.
2) if the error persist, try to replace Keyboard Interface Board first and CPU board
second.
|VALIS SCI error |
|
|
|
|
This message could be appear if an error occur on the communication between CPU
and DISP3 chips.
Possible solutions:
1) verify all the tracks, solders and components between CPU and DISP3 chips as
shown in schematics.
2) if the error persist, replace the CPU board and send back to generalmusic the failed
CPU board.
|Disp Failure
|
|
|
|
|
|
|
|
5J
J6
7J
J8
9J
J 10
11 J
J 12
13 J
J 14
CPU & SOUND GENERATOR BOARD
PCB# 310603/1
15 J
J 16
17 J
Spare Part List
Legend
EU
US
R
B
M
W
Baldwin
Gem
Code
=
Specify European Version (230Vac)
=
Specify United States Version (115Vac)
=
Rosewood finish
=
Gloss Black finish
=
Mahogany finish
=
Gloss White finish
=
Baldwin version
=
Gem version
Description
RP100
230568
140010
020493
010545
340916
190133
171638
140036
110614
020493
*
10mH 250Vac 1A AC Line EMI Coil “Siemens”
*
3 Contacts P=10 Vert Terminal Block
*
100n 250Vac MKP EMI Capacitor “Siemens”
*
4n7 250V Ceramic Capacitor (Iec-Ul-Csa)
Button for Power Switch
Lateroid Insulator For Screw Block
Mains Switch Support
Screw Block (specify contacts)
Mains Socket
100n 250Vac MKP EMI Capacitor “Siemens”
230136
230137
Transformer 230Vac 130W (EU)
Transformer 115Vac 130W (US)
Transformers
Accessories
970243
970346
271243
271266
271236
130274
130276
Pianist’s Bench
Portable Triple Pedal Switch
Owner’s Manual (English,Italian,French,German)(Gem)
Owner’s Manual (Dutch,Spanish,Danish)(Gem)
Owner’s Manual (English, French, Spanish)(Baldwin)
Mains Cable (EU)
Mains Cable (US)
Consolette
970345
660603
660511
660510
651924
261820
261819
261818
261092
150618
120687
120686
120685
Consolette
*
Lower Cross-Bar Strengthening
*
Left Cabinet Support
*
Right Cabinet Support
*
Foot
*
Lower Cross-Bar
*
Left Leg
*
Right Leg
*
Upper Cross-Bar
*
Thumbscrew
*
Barrel Nut
*
Conical Screw
*
Threaded Rod
710472
710471
660606
660553
660505
660509
660508
653427
653426
652875
340075
210017
210016
190015
171657
171656
653431
653430
340811
171651
120690
720565
660599
660598
660597
340922
340912
340119
190015
Cabinet (Gem)
Cabinet (Baldwin)
Cover
Keyboard Cross-Bar (Gem)
Keyboard Cross-Bar (Baldwin)
Flange for Left Side
Flange for Right Side
Left Side
Right Side
Speaker Grid
Nylon Board Spacer
2x10mm Adhesive Black Felt (specify mt)
1x10mm Adhesive Black Felt (specify mt)
Adhesive Rubber Foot
Left Side Support
Right Side Support
Music Stand
Music Stand Stop
Music Stand Assembly (Gem)
Music Stand Assembly (Baldwin)
*
Wooden Music Stand Support (Gem)
*
Wooden Music Stand Support (Baldwin)
*
Plexiglass Music Stand
*
Music Stand Hinge
*
2x10mm Adhesive Black Felt (specify mt)
Keyboard Cover
Left Rack
Right Rack
Toothed Wheel
Toothed Wheel Bar
Toothed Wheel Lock
Keyboard Cover Assembly
*
Bar Support Profile for Keyb. Cover
*
Top Handle Profile for Keyb. Cover
*
Bottom Handle Profile for Keyb. Cover
*
Plastic Sliding Cap for Handle
*
Plexiglass Keyboard Cover
*
Bush
*
Adhesive Rubber Foot
770839
770834
110320
768197
Mains Cables Assembly
Power Switch Cables Assembly
*
Power Switch
Mains Filter Board (Pcb#310642)
Cabinet
340913
720566
720564
710466
710465
340914
170612
210017
Mains Assembly
J 18
Power Amplifier & Supply Board
730675
340154
340079
340078
141010
140917
140352
140351
140010
110119
100958
100919
100059
100045
100043
090856
090183
080605
080156
080103
110013
110003
110061
110026
Power Amplifier & Supply Board (Pcb#310543)
*
TO3/TO218 Mica Washer
*
TO220 Mica Washer
*
TO220 Insulated Bush
*
4 Contacts Vert Female Connector
*
2 Contacts Vert Male Connector
*
9 Contacts Hor Male Connector
*
6 Contacts Hor Male Connector
*
3 Contacts P=10 Vert Terminal Block
*
Fuse Clip 10A max (EU) (US)
*
TDA7265 Dual 25W Power Amplifier
*
MC33078 Dual LN Operational Amplifier
*
7805 +5V 1A Voltage Regulator
*
7812 +12V 1A Voltage Regulator
*
7912 -12V 1A Voltage Regulator
*
J176 TO92 P-Channel J-Fet Transistor
*
BC550 TO92 LN Npn Transistor
*
KBL02 4A 200V Rectifier Diode Bridge
*
1N4002 1A 100V Rectifier Diode
*
1N4148 100mA 75V Signal Diode
T1.25A Fuse 5x20mm (EU)
T3.15A Fuse 5x20mm (EU)
T3A Fuse 6.3x32mm (US)
T1.25A Fuse 6.3x32mm (US)
Speakers Assembly
770835
261788
220117
220115
030171
Speakers Cables Assembly
Speaker Box
8ohm 5" Woofer Speaker
8ohm 3" Tweeter Speaker
4u7 63V 20% Axial Electrolytic Bipolar Capacitor
730516
230569
140351
140217
140207
Phones Board (Pcb# 310541)
*
FL5R200PNT EMI Coil For Signal
*
6 Contacts Hor Male Connector
*
Jack Slim Horizontal S-F Socket
*
Jack Horizontal F Socket (with dual switch)
Phones Board
Keyboard Assembly
720558
840762
840761
761173
141018
141011
140918
100740
100605
050493
050492
050414
010725
010662
010661
720560
840738
810552
340764
340211
141018
141010
080103
810551
340212
340211
141018
141010
080103
Keyboard Assembly (TP21)
*
20 Wires 25cm Length Flat Cable
*
20 Wires 12.5cm Length Flat Cable
*
Keyboard Interface Board (Pcb#315024)
**
20 Contacts Vert Female Connector
**
6 Contacts Vert Female Connector
**
2 Contacts Hor Male Connector
**
HD6433278 Cpu F=20MHz
**
74HC125 Quad 3-State Buffer
**
10Kx4 1/8w 5% Resistor Array
**
10Kx8 1/8w 5% Resistor Array
**
2K2x4 1/8w 5% Resistor Array
**
20MHz Ceramic Resonator With Capacitors
**
220p 10% 50V X8 Cap Array
**
47p 10% 50V X8 Cap Array
*
Keyboard Assembly (TP21)
**
4 Wires 5cm Length Flat Cable
**
39 Contacts L Board For Dynamic Keyb. (PCB#310531)
*** 3 Dual Contacts Rubber Strip
*** 12 Dual Contact Rubber Strip
*** 20 Contacts Vert Female Connector
*** 4 Contacts Vert Female Connector
*** 1N4148 100mA 75V Signal Diode
**
49 Contacts R Board For Dynamic Keyb. (PCB#310530)
*** 13 Dual Contact Rubber Strip
*** 12 Dual Contact Rubber Strip
*** 20 Contacts Vert Female Connector
*** 4 Contacts Vert Female Connector
*** 1N4148 100mA 75V Signal Diode
500075
160217
160216
151236
151235
151234
151233
151232
151231
151230
151229
151228
151227
**
***
***
***
***
***
***
***
***
***
***
***
***
Mechanical Keyboard (TP21)
Sharp Key Return Spring
Natural Key Return Spring
Last C Key (TP21P)
First A Key (TP21P)
Sharp Key (TP21P)
B Key (TP21P)
A Key (TP21P)
G Key (TP21P)
F Key (TP21P)
E Key (TP21P)
D Key (TP21P)
C Key (TP21P)
Controls Panel Assembly
820583
820582
810677
730999
141018
140918
140529
100606
090194
080752
080724
080103
070551
730997
323069
141018
140918
140890
080745
660591
660592
653420
653419
653418
653417
653415
653413
651648
340915
340820
340523
340512
210258
210020
210017
Controls Panel Assembly (Gem)
Controls Panel Assembly (Baldwin)
*
Controls & Display Boards Assembly
**
Controls Panel Board (Pcb#310609)
*** 20 Contacts Vert Female Connector
*** 2 Contacts Hor Male Connector
*** Microswitch 12V 50mA 0.25mm
*** 74HC138 1 Of 8 Decoder
*** BC560 TO92 LN Pnp Transistor
*** Led 3mm Wide Diffused Red
*** Led 3mm 40deg High Eff Green
*** 1N4148 100mA 75V Signal Diode
*** 10K Linear 30mm Slider Potentiometer
**
Display Board (Pcb#310638)
*** 11.1X5mm Bumpon Rubber
*** 20 Contacts Vert Female Connector
*** 2 Contacts Hor Male Connector
*** 4 Contacts Hor Male Single-Strip
*** 2x16 Characters Lcd Display
*
Controls Panel (Gem)
*
Controls Panel (Baldwin)
*
<+ -> Rubber Pad
*
<< >> Rubber Pad
*
<PLAY-REC> Rubber Pad
*
2+4+8+8 Rubber Pad
*
5+5+2 Rubber Pad
*
4+1 Rubber Pad
*
Plexiglass Display Screen
*
LED Lens
*
Slider Knob
*
6.5mm Spacer
*
Slider Potentiometer Guide
*
Slider Potentiometer Felt
*
1.5x12mm Adhesive Red Felt (specify mt)
*
2x10mm Adhesive Black Felt (specify mt)
761171
560021
560020
141018
141012
141011
141010
140930
140874
106003
106001
105009
105006
104042
104041
104030
104000
103012
103010
103009
103004
103002
103001
091001
091000
081204
081000
055101
055100
011501
011500
010727
010704
140877
110282
*
*
Jumper For Contacts Strip (p=2.54mm)
3.6V 60mAh Nicd Battery
730996
730995
230569
230527
141012
141010
140918
140908
140247
140217
140216
140212
120857
100734
100602
100035
090194
090183
080103
653440
210018
171329
Outputs Assembly
*
Outputs Board (Pcb#310608)
**
FL5R200PNT EMI Coil For Signal
**
BL02RN2-R62 EMI Coil For Signal
**
8 Contacts Vert Female Connector
**
4 Contacts Vert Female Connector
**
2 Contacts Hor Male Connector
**
6 Contacts Vert Male Small Connector
**
8 Poles Mini Din Female Socket
**
Jack Slim Horizontal S-F Socket
**
6 Poles Din Horizontal Female Socket
**
5 Poles Din Horizontal Female Socket
**
Vertical Male Faston 6.3mm
**
MAX202E RS232 Drivers/Receiver
**
74HC04 Hex Inverter
**
6N138 Optocoupler
**
BC560 TO92 LN Pnp Transistor
**
BC550 TO92 LN Npn Transistor
**
1N4148 100mA 75V Signal Diode
*
Outputs Panel
*
1x5mm Adhesive Red Felt (specify mt)
*
Support for Outputs Panel
Outputs Assembly
Wiring Connections
841174
841173
841172
841043
841038
841036
840844
840842
840768
840765
20 Wires 20cm Length Flat Cable (3 Connectors)
6 Wires 7.5cm Length Crimp Terminal Cable
9 Wires 15cm Length Crimp Terminal Cable
2 Wires 35cm Length Crimp Terminal Cable
8 Wires 25cm Length Flat Cable
6 Wires 45cm Length Flat Cable
2 Wires 7.5cm Length Crimp Terminal Cable
4 Wires 15cm Length Flat Cable
4 Wires 10cm Length Flat Cable
2 Wires 20cm Length Crimp Terminal Cable
RP150
Accessories
CPU & Sound Generator Board
970319
970297
970296
340116
271276
271259
271267
130274
130276
Pianist’s Bench (M)
Pianist’s Bench (B)
Pianist’s Bench (R)
Adhesive Clamp For Pedals Cable
Owner’s Manual (English,French,Spanish)(Baldwin)
Owner’s Manual (English,Italian,French,German)(Gem)
Owner’s Manual (Dutch,Spanish,Danish)(Gem)
Mains Cable (EU)
Mains Cable (US)
CPU & Sound Generator Board (Pcb#310603)
*
GAL 16V8C-7 Programmed Disp3 Ram Read
*
GAL 16V8C-7 Programmed Disp3 Ram Write
*
20 Contacts Vert Female Connector
*
8 Contacts Vert Female Connector
*
6 Contacts Vert Female Connector
*
4 Contacts Vert Female Connector
*
9 Contacts Hor Male Connector
*
Single In Line Vert Male Strip (specify contacts)
*
MAX709 Power Monitor With Reset
*
MC33078P SOIC Dual Low Noise Op. Amp.
*
DISP3 QFP Digital Sound Processor (Hitachi)
*
HD6413003F16 QFP Cpu
*
HM5118160J-5 16Mbit Dram Ta=50nS
*
23C64000G SOP 64MBit Rom Wave98
*
AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS
*
HM628128LFP5 SOP 1Mbit Static Ram Ta=55nS
*
74HC125D SOIC Quad Tri-State Buffer
*
74HC04D SOIC Hex Inverter
*
74HC02D SOIC Quad 2-In Nor Gate
*
AD1865R SOP 18bit D/A Converter
*
74HC245DW SOIC Octal Bus Transceiver
*
74HC08D SOIC Quad 2-Input And Gate
*
BC857 TO236 Smd Pnp Transistor
*
BC847 TO236 Smd Npn Transistor
*
5.6V 0.5W Zener
*
PMLL4148 Smd 100mA 75V Signal Diode
*
4K7 X4 1/16w 5% Smd Resistor Array
*
100E X4 1/16w 5% Smd Resistor Array
*
220pF x4 10% 100V NP0 Smd Capacitor Array
*
47pF x4 10% 100V NP0 Smd Capacitor Array
*
45.1584MHz Quartz Resonator
*
16MHz Quartz Resonator
830746
830745
830744
710504
710503
710502
720561
070556
510258
510257
510256
261965
261946
261866
261812
261952
261831
261806
261953
261830
261807
261811
210021
171585
660407
261943
261940
261937
261962
261828
261809
Legs & Pedals Assembly (M)
Legs & Pedals Assembly (B)
Legs & Pedals Assembly (R)
*
Pedals Cross-bar Assembly (M)
*
Pedals Cross-bar Assembly (B)
*
Pedals Cross-bar Assembly (R)
**
Triple Brassed Pedals Assembly
*** 20K 90deg stroke potentiometer
**
Pedal Wooden Parts (M)
**
Pedal Wooden Parts (B)
**
Pedal Wooden Parts (R)
*** 20x20x70mm Deal Fillet
*** Rear Cross-Bar for Pedals
*** 20x20x200mm Deal Fillet
*** Support for Pedalboard
*** Top Cross-Bar for Pedals (M)
*** Top Cross-Bar for Pedals (B)
*** Top Cross-Bar for Pedals (R)
*** Front Cross-Bar for Pedals (M)
*** Front Cross-Bar for Pedals (B)
*** Front Cross-Bar for Pedals (R)
**
Pedalboard
**
1x15mm Adhesive Red Felt (specify mt)
**
Angular Fixing for Pedals Cross-bar
*
Speaker Box Fixing
*
Lower Panel (M)
*
Lower Panel (B)
*
Lower Panel (R)
*
Left Foot (M)
*
Left Foot (B)
*
Left Foot (R)
Consolette
261961
261829
261808
261951
261833
261803
261950
261834
261802
171702
171701
*
*
*
*
*
*
*
*
*
*
*
Right Foot (M)
Right Foot (B)
Right Foot (R)
Left Side (M)
Left Side (B)
Left Side (R)
Right Side (M)
Right Side (B)
Right Side (R)
Right Cabinet Support
Left Cabinet Support
Cabinet
710534
710533
710532
510268
510267
510266
261866
261958
261837
261798
340090
710544
710543
710542
710523
710522
710521
710553
710552
710551
710501
710500
710499
324405
261944
261941
261938
219066
210016
171679
171669
171664
710520
710519
710518
660612
340922
340811
340119
261949
261948
261947
210017
210016
171665
171335
120690
710557
710556
710555
710513
710512
710511
660609
660410
660405
510264
510262
510260
510263
510261
510259
710540
710480
710469
710497
710481
710470
Top Cabinet Assembly
Top Cabinet Assembly (M)
Top Cabinet Assembly (B)
Top Cabinet Assembly (R)
*
Top Cover Assembly (M)
*
Top Cover Assembly (B)
*
Top Cover Assembly (R)
**
20x20x200mm Deal Fillet
**
Cabinet Cover (M)
**
Cabinet Cover (B)
**
Cabinet Cover (R)
*
Music Stand Bush
Front Panel Assembly
Front Panel Assembly (Baldwin) (M)
Front Panel Assembly (Baldwin) (B)
Front Panel Assembly (Baldwin) (R)
Front Panel Assembly (Gem)(M)
Front Panel Assembly (Gem)(B)
Front Panel Assembly (Gem)(R)
*
Front Panel (Baldwin)(M)
*
Front Panel (Baldwin)(B)
*
Front Panel (Baldwin)(R)
*
Front Panel (Gem)(M)
*
Front Panel (Gem)(B)
*
Front Panel (Gem)(R)
*
Hinge
*
Music Stand (M)
*
Music Stand (B)
*
Music Stand (R)
*
Adhesive Black Felt for Music Stand
*
1x10mm Adhesive Black Felt (specify mt)
*
Front Panel Angular Reinforcement
*
Left Fixing Bar
*
Right Fixing Bar
Keyboard Cover Assembly
Keyboard Cover Assembly (M)
Keyboard Cover Assembly (B)
Keyboard Cover Assembly (R)
*
Front Keyboard Cover Handle
*
Plastic Sliding Cap for Handle
*
Toothed Wheel
*
Bush
*
Keyboard Cover (M)
*
Keyboard Cover (B)
*
Keyboard Cover (R)
*
2x10mm Adhesive Black Felt (specify mt)
*
1x10mm Adhesive Black Felt (specify mt)
*
Keyboard Cover Bar Support
*
Toothed Wheel Bar
*
Toothed Wheel Lock
Cabinet Assembly
Cabinet (Baldwin) (M)
Cabinet (Baldwin) (B)
Cabinet (Baldwin) (R)
Cabinet (Gem) (M)
Cabinet (Gem) (B)
Cabinet (Gem) (R)
*
Speaker Socket Support
*
Speakers Protection Grid
*
Heatsink Grid
*
Cabinet Wooden Parts (Baldwin) (M)
*
Cabinet Wooden Parts (Baldwin) (B)
*
Cabinet Wooden Parts (Baldwin) (R)
*
Cabinet Wooden Parts (Gem) (M)
*
Cabinet Wooden Parts (Gem) (B)
*
Cabinet Wooden Parts (Gem) (R)
**
Keyboard Cross-Bar (Baldwin) (M)
**
Keyboard Cross-Bar (Baldwin) (B)
**
Keyboard Cross-Bar (Baldwin) (R)
**
Keyboard Cross-Bar (Gem) (M)
**
Keyboard Cross-Bar (Gem) (B)
**
Keyboard Cross-Bar (Gem) (R)
710541
710474
710467
710498
710475
710468
261840
261954
261841
261791
261955
261842
261790
340904
323012
171331
171330
150474
653433
653432
340075
210217
210216
210054
**
Rear Panel (Baldwin) (M)
**
Rear Panel (Baldwin) (B)
**
Rear Panel (Baldwin) (R)
**
Rear Panel (Gem) (M)
**
Rear Panel (Gem) (B)
**
Rear Panel (Gem) (R)
**
Bottom Support Panel
**
Cabinet Right Side (M)
**
Cabinet Right Side (B)
**
Cabinet Right Side (R)
**
Cabinet Left Side (M)
**
Cabinet Left Side (B)
**
Cabinet Left Side (R)
*
Toothed Bar
*
Plastic Pivot
*
Left Cover Clamp
*
Right Cover Clamp
*
Plug For Unused Hole
Left Plastic Lateral
Right Plastic Lateral
Nylon Board Spacer
Black Sealer (specify mt)
Adhesive Rubber Foam 20x5mm (Specify mt)
1x5mm Adhesive Spik (specify mt)
770860
110320
340916
171638
110614
768197
230568
140010
020493
010545
Mains Cables Assembly
*
Power Switch
Switch Button
Mains Switch Support
Mains Socket
Mains Filter Board (Pcb#310642)
*
10mH 250Vac 1A AC Line EMI Coil “Siemens”
*
3 Contacts P=10 Vert Terminal Block
*
100n 250Vac MKP EMI Capacitor “Siemens”
*
4n7 250V Ceramic Capacitor (Iec-Ul-Csa)
230137
230136
Transformer 115Vac 130W (US)
Transformer 230Vac 130W (EU)
Mains Assembly
Transformer
Power Amplifier & Supply Board
730675
340154
340079
340078
141010
140917
140352
140351
140010
110119
100958
100919
100059
100045
100043
090856
090183
080605
080156
080103
110013
110003
110061
110026
Power Amplifier & Supply Board (Pcb#310543)
*
TO3/TO218 Mica Washer
*
TO220 Mica Washer
*
TO220 Insulated Bush
*
4 Contacts Vert Female Connector
*
2 Contacts Vert Male Connector
*
9 Contacts Hor Male Connector
*
6 Contacts Hor Male Connector
*
3 Contacts P=10 Vert Terminal Block
*
Fuse Clip 10A max (EU) (US)
*
TDA7265 Dual 25W Power Amplifier
*
MC33078 Dual LN Operational Amplifier
*
7805 +5V 1A Voltage Regulator
*
7812 +12V 1A Voltage Regulator
*
7912 -12V 1A Voltage Regulator
*
J176 TO92 P-Channel J-Fet Transistor
*
BC550 TO92 LN Npn Transistor
*
KBL02 4A 200V Rectifier Diode Bridge
*
1N4002 1A 100V Rectifier Diode
*
1N4148 100mA 75V Signal Diode
T1.25A Fuse 5x20mm (EU)
T3.15A Fuse 5x20mm (EU)
T3A Fuse 6.3x32mm (US)
T1.25A Fuse 6.3x32mm (US)
770859
220120
220119
340928
210242
171699
Speaker Cables Assembly
6" Full-range 8E Speaker
3" Full-range 8E Speaker
Plastic Speaker Box
Filler for Speaker Box (Specify m²)
3" Speaker Support
Speakers Assembly
Keyboard Assembly
720568
840762
840761
761173
141018
141011
140918
100740
100605
Keyboard Assembly (TP10MDS)
*
20 Wires 25cm Length Flat Cable
*
20 Wires 12.5cm Length Flat Cable
*
Keyboard Interface Board (Pcb#315024)
**
20 Contacts Vert Female Connector
**
6 Contacts Vert Female Connector
**
2 Contacts Hor Male Connector
**
HD6433278 Cpu F=20MHz
**
74HC125 Quad 3-State Buffer
050493
050492
050414
010725
010662
010661
720559
840738
810552
340764
340211
141018
141010
080103
810551
340212
340211
141018
141010
080103
500074
151226
151225
151224
151223
151222
151221
151220
151219
151218
151217
340092
210017
**
**
**
**
**
**
*
**
**
***
***
***
***
***
**
***
***
***
***
***
**
***
***
***
***
***
***
***
***
***
***
*
*
10Kx4 1/8w 5% Resistor Array
10Kx8 1/8w 5% Resistor Array
2K2x4 1/8w 5% Resistor Array
20MHz Ceramic Resonator With Capacitors
220p 10% 50V X8 Cap Array
47p 10% 50V X8 Cap Array
Keyboard Assembly (TP10MDS)
4 Wires 5cm Length Flat Cable
39 Contacts L Board For Dynamic Keyb. (PCB#310531)
3 Dual Contacts Rubber Strip
12 Dual Contact Rubber Strip
20 Contacts Vert Female Connector
4 Contacts Vert Female Connector
1N4148 100mA 75V Signal Diode
49 Contacts R Board For Dynamic Keyb. (PCB#310530)
13 Dual Contact Rubber Strip
12 Dual Contact Rubber Strip
20 Contacts Vert Female Connector
4 Contacts Vert Female Connector
1N4148 100mA 75V Signal Diode
Mechanicals Parts (TP10MDS)
Last C Key (TP10MDS)
First A Key (TP10MDS)
Sharp Key (TP10MDS)
B Key (TP10MDS)
A Key (TP10MDS)
G Key (TP10MDS)
F Key (TP10MDS)
E Key (TP10MDS)
D Key (TP10MDS)
C Key (TP10MDS)
5mm Board Spacer
2x10mm Adhesive Black Felt (specify mt)
820592
820590
810677
730999
141018
140918
140529
100606
090194
080752
080724
080103
070551
730997
323069
141018
140918
140890
080745
660635
660610
653420
653419
653418
653417
653415
653413
651648
651563
340915
340820
340523
340512
210258
210020
210017
171661
Controls Panel Assembly (Baldwin)
Controls Panel Assembly (Gem)
*
Controls & Display Boards Assembly
**
Controls Panel Board (Pcb#310609)
*** 20 Contacts Vert Female Connector
*** 2 Contacts Hor Male Connector
*** Microswitch 12V 50mA 0.25mm
*** 74HC138 1 Of 8 Decoder
*** BC560 TO92 LN Pnp Transistor
*** Led 3mm Wide Diffused Red
*** Led 3mm 40deg High Eff Green
*** 1N4148 100mA 75V Signal Diode
*** 10K Linear 30mm Slider Potentiometer
**
Display Board (Pcb#310638)
*** 11.1X5mm Bumpon Rubber
*** 20 Contacts Vert Female Connector
*** 2 Contacts Hor Male Connector
*** 4 Contacts Hor Male Single-Strip
*** 2x16 Characters Lcd Display
*
Control Panel (Baldwin)
*
Control Panel (Gem)
*
<+ -> Rubber Pad
*
<< >> Rubber Pad
*
<PLAY-REC> Rubber Pad
*
2+4+8+8 Rubber Pad
*
5+5+2 Rubber Pad
*
4+1 Rubber Pad
*
Plexiglass Display Screen
*
Cloth For Panel Slits
*
LED Lens
*
Slider Knob
*
6.5mm Spacer
*
Slider Potentiometer Guide
*
Slider Potentiometer Felt
*
1.5x12mm Adhesive Red Felt (specify mt)
*
2x10mm Adhesive Black Felt (specify mt)
*
Front Support
761171
560021
560020
141018
141012
141011
141010
140930
140874
106003
106001
CPU & Sound Generator Board (Pcb#310603)
*
GAL 16V8C-7 <DISP3 RAM READ
*
GAL 16V8C-7 <DISP3 RAM WRITE
*
20 Contacts Vert Female Connector
*
8 Contacts Vert Female Connector
*
6 Contacts Vert Female Connector
*
4 Contacts Vert Female Connector
*
9 Contacts Hor Male Connector
*
Single In Line Vert Male Strip (specify contacts)
*
MAX709 Power Monitor With Reset
*
MC33078P SOIC Dual Low Noise Op. Amp.
Controls Panel Assembly
CPU & Sound Generator Board
105009
105006
104042
104041
104030
104000
103012
103010
103009
103004
103002
103001
091001
091000
081204
081000
055101
055100
011501
011500
010727
010704
140877
110282
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
DISP3 QFP Digital Sound Processor (Hitachi)
HD6413003F16 QFP Cpu
HM5118160J-5 16Mbit Dram Ta=50nS
23C64000G SOP 64MBit Rom Wave98
AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS
HM628128LFP5 SOP 1Mbit Static Ram Ta=55nS
74HC125D SOIC Quad Tri-State Buffer
74HC04D SOIC Hex Inverter
74HC02D SOIC Quad 2-In Nor Gate
AD1865R SOP 18bit D/A Converter
74HC245DW SOIC Octal Bus Transceiver
74HC08D SOIC Quad 2-Input And Gate
BC857 TO236 Smd Pnp Transistor
BC847 TO236 Smd Npn Transistor
5.6V 0.5W Zener
PMLL4148 Smd 100mA 75V Signal Diode
4K7 X4 1/16w 5% Smd Resistor Array
100E X4 1/16w 5% Smd Resistor Array
220pF x4 10% 100V NP0 Smd Capacitor Array
47pF x4 10% 100V NP0 Smd Capacitor Array
45.1584MHz Quartz Resonator
16MHz Quartz Resonator
Jumper For Contacts Strip (p=2.54mm)
3.6V 60mAh Nicd Battery
731019
140323
060253
030348
HF
*
*
*
730996
730995
230569
230527
141012
141010
140918
140908
140247
140217
140216
140212
100734
100602
100035
090194
090183
080103
653440
210018
171329
Outputs Assembly
*
Outputs Board (Pcb#310608)
**
FL5R200PNT EMI Coil For Signal
**
BL02RN2-R62 EMI Coil For Signal
**
8 Contacts Vert Female Connector
**
4 Contacts Vert Female Connector
**
2 Contacts Hor Male Connector
**
6 Contacts Vert Male Small Connector
**
8 Poles Mini Din Female Socket
**
Jack Slim Horizontal S-F Socket
**
6 Poles Din Horizontal Female Socket
**
5 Poles Din Horizontal Female Socket
**
MAX202E RS232 Drivers/Receiver
**
74HC04 Hex Inverter
**
6N138 Optocoupler
**
BC560 TO92 LN Pnp Transistor
**
BC550 TO92 LN Npn Transistor
**
1N4148 100mA 75V Signal Diode
*
Output Panel Box
*
1x5mm Adhesive Red Felt (specify mt)
*
Support for Output Panel Box
730674
730516
230569
140351
140217
140207
652854
210017
Phones Assembly
*
Phones Board (pcb# 310541)
**
FL5R200PNT EMI Coil For Signal
**
6 Contacts Hor Male Connector
**
Jack Slim Horizontal S-F Socket
**
Jack Horizontal F Socket (with dual switch)
*
Phones Board Support
*
2x10mm Adhesive Black Felt (specify mt)
841206
841205
841176
841173
841063
841043
841041
841010
840844
840799
4 Wires 20cm Length Flat Cable
9 Wires 7.5cm Length Crimp Terminal Cable
20 Wires 48cm Length Flat Cable (3 Connectors)
6 Wires 7.5cm Length Crimp Terminal Cable
6 Wires 55cm Length Flat Cable
2 Wires 35cm Length Crimp Terminal Cable
8 Wires 12.5cm Length Flat Cable
2 Wires 50cm Length Crimp Terminal Cable
2 Wires 7.5cm Length Crimp Terminal Cable
4 Wires 7.5cm Length Flat Cable
HF Crossover Filter Board
Crossover Filter Board (Pcb#310654)
6 Contacts Vert Male Connector
10E 5W 10% Wire Resistor
47u 100V 20% Axial Electrolytic Bipolar Capacitor
Outputs Assembly
Phones Assembly
Wiring Connections
RP200
Accessories
970319
970297
970296
970298
340116
Pianist’s Bench (M)
Pianist’s Bench (B)
Pianist’s Bench (R)
Pianist’s Bench (W)
Adhesive Clamp For Pedals Cable
271237
271268
271258
130274
130276
Owner’s Manual (English, Italian, French, German)(Gem)
Owner’s Manual (Dutch,Spanish,Danish)(Gem)
Owner’s Manual (English, French, Spanish)(Baldwin)
Mains Cable (EU)
Mains Cable (US)
830743
830742
830741
830752
710530
340159
261805
210074
710517
710516
710515
710549
770727
510265
510243
510245
510244
261963
261832
261804
261848
261823
261822
261821
261794
261793
340159
220118
210242
710504
710503
710502
710550
720561
510258
510257
510256
510270
261965
261946
261866
261952
261831
261806
261847
261953
261830
261807
261846
261812
261811
210021
171585
120681
660407
261950
261834
261802
261850
261951
261833
261803
261849
261961
261829
261808
261845
261962
261828
261809
261844
171702
171701
Legs & Pedals Assembly (M)
Legs & Pedals Assembly (B)
Legs & Pedals Assembly (R)
Legs & Pedals Assembly (W)
*
Cloth Panel Assembly
**
3M Dual Lock Fastening (Specify mt)
**
Cloth Panel
**
Speaker Cloth
*
Speaker Box Assembly (M)
*
Speaker Box Assembly (B)
*
Speaker Box Assembly (R)
*
Speaker Box Assembly (W)
**
Speaker Cables Assembly
**
Speaker Box (M)
**
Speaker Box (B)
**
Speaker Box (R)
**
Speaker Box (W)
*** Speaker Box Rear Panel (M)
*** Speaker Box Rear Panel (B)
*** Speaker Box Rear Panel (R)
*** Speaker Box Rear Panel (W)
*** Speaker Box Lower Panel
*** Speaker Box Upper Panel
*** Speaker Box Divider Panel
*** Speaker Box Front Panel
*** Speaker Box Side Panel
**
3M Dual Lock Fastening (Specify mt)
**
8ohm 8" Woofer Speaker
**
Filler for Speaker Box (Specify m²)
*
Pedals Cross-bar Assembly (M)
*
Pedals Cross-bar Assembly (B)
*
Pedals Cross-bar Assembly (R)
*
Pedals Cross-bar Assembly (W)
**
Triple Brassed Pedals Assembly
**
Pedal Wooden Parts (M)
**
Pedal Wooden Parts (B)
**
Pedal Wooden Parts (R)
**
Pedal Wooden Parts (W)
*** 20x20x70mm Deal Fillet
*** Rear Cross-Bar for Pedals
*** 20x20x200mm Deal Fillet
*** Top Cross-Bar for Pedals (M)
*** Top Cross-Bar for Pedals (B)
*** Top Cross-Bar for Pedals (R)
*** Top Cross-Bar for Pedals (W)
*** Front Cross-Bar for Pedals (M)
*** Front Cross-Bar for Pedals (B)
*** Front Cross-Bar for Pedals (R)
*** Front Cross-Bar for Pedals (W)
*** Support for Pedalboard
**
Pedalboard
**
1x15mm Adhesive Red Felt (specify mt)
**
Angular Fixing for Pedals Cross-bar
**
Sleeve for Internal Cheek Block
*
Speaker Box Fixing
*
Right Side (M)
*
Right Side (B)
*
Right Side (R)
*
Right Side (W)
*
Left Side (M)
*
Left Side (B)
*
Left Side (R)
*
Left Side (W)
*
Right Foot (M)
*
Right Foot (B)
*
Right Foot (R)
*
Right Foot (W)
*
Left Foot (M)
*
Left Foot (B)
*
Left Foot (R)
*
Left Foot (W)
*
Right Cabinet Support
*
Left Cabinet Support
Consolette
Cabinet
710534
710533
Top Cabinet Assembly
Top Cabinet Assembly (M)
Top Cabinet Assembly (B)
710532
710546
510268
510267
510266
510269
261866
261958
261837
261798
261853
340090
710528
710526
710524
710529
710527
710525
710545
710536
710535
710531
710539
710538
710537
710548
340919
261959
261839
261795
261855
261796
210016
171677
171669
171667
171664
710520
710519
710518
710547
660612
340922
340811
340119
261949
261948
261947
261978
210017
210016
171665
171335
120690
710509
710507
710505
710510
710508
710506
710554
660609
660405
510263
510261
510259
510264
510262
510260
510271
710497
710481
710470
710540
710480
710469
710476
710498
710475
710468
710541
710474
Top Cabinet Assembly (R)
Top Cabinet Assembly (W)
*
Top Cover Assembly (M)
*
Top Cover Assembly (B)
*
Top Cover Assembly (R)
*
Top Cover Assembly (W)
**
20x20x200mm Deal Fillet
**
Cabinet Cover (M)
**
Cabinet Cover (B)
**
Cabinet Cover (R)
**
Cabinet Cover (W)
*
Music Stand Bush
Front Panel Assembly
Front Panel Assembly (Gem)(M)
Front Panel Assembly (Gem)(B)
Front Panel Assembly (Gem)(R)
Front Panel Assembly (Baldwin)(M)
Front Panel Assembly (Baldwin)(B)
Front Panel Assembly (Baldwin)(R)
Front Panel Assembly (Baldwin)(W)
*
Front Finishing Fillet (Gem) (M)
*
Front Finishing Fillet (Gem) (B)
*
Front Finishing Fillet (Gem) (R)
*
Front Finishing Fillet (Baldwin) (M)
*
Front Finishing Fillet (Baldwin) (B)
*
Front Finishing Fillet (Baldwin) (R)
*
Front Finishing Fillet (Baldwin) (W)
*
Music Stand
*
Centre Front Panel (M)
*
Centre Front Panel (B)
*
Centre Front Panel (R)
*
Centre Front Panel (W)
*
Wooden Front Panel
*
1x10mm Adhesive Black Felt (specify mt)
*
Left Speaker Grid
*
Left Fixing Bar
*
Right Speaker Grid
*
Right Fixing Bar
Keyboard Cover Assembly
Keyboard Cover Assembly (M)
Keyboard Cover Assembly (B)
Keyboard Cover Assembly (R)
Keyboard Cover Assembly (W)
*
Front Keyboard Cover Handle
*
Plastic Sliding Cap for Handle
*
Toothed Wheel
*
Bush
*
Keyboard Cover (M)
*
Keyboard Cover (B)
*
Keyboard Cover (R)
*
Keyboard Cover (W)
*
2x10mm Adhesive Black Felt (specify mt)
*
1x10mm Adhesive Black Felt (specify mt)
*
Keyboard Cover Bar Support
*
Toothed Wheel Bar
*
Toothed Wheel Lock
Cabinet Assembly
Cabinet (Gem) (M)
Cabinet (Gem) (B)
Cabinet (Gem) (R)
Cabinet (Baldwin) (M)
Cabinet (Baldwin) (B)
Cabinet (Baldwin) (R)
Cabinet (Baldwin) (W)
*
Speaker Socket Support
*
Heatsink Grid
*
Cabinet Wooden Parts (Gem) (M)
*
Cabinet Wooden Parts (Gem) (B)
*
Cabinet Wooden Parts (Gem) (R)
*
Cabinet Wooden Parts (Baldwin) (M)
*
Cabinet Wooden Parts (Baldwin) (B)
*
Cabinet Wooden Parts (Baldwin) (R)
*
Cabinet Wooden Parts (Baldwin) (W)
**
Keyboard Cross-Bar (Gem) (M)
**
Keyboard Cross-Bar (Gem) (B)
**
Keyboard Cross-Bar (Gem) (R)
**
Keyboard Cross-Bar (Baldwin) (M)
**
Keyboard Cross-Bar (Baldwin) (B)
**
Keyboard Cross-Bar (Baldwin) (R)
**
Keyboard Cross-Bar (Baldwin) (W)
**
Rear Panel (Gem) (M)
**
Rear Panel (Gem) (B)
**
Rear Panel (Gem) (R)
**
Rear Panel (Baldwin) (M)
**
Rear Panel (Baldwin) (B)
19 J
710467
710478
261955
261842
261790
261858
261954
261841
261791
261857
261840
340904
323012
261813
171331
171330
653433
653432
340075
**
Rear Panel (Baldwin) (R)
**
Rear Panel (Baldwin) (W)
**
Cabinet Left Side (M)
**
Cabinet Left Side (B)
**
Cabinet Left Side (R)
**
Cabinet Left Side (W)
**
Cabinet Right Side (M)
**
Cabinet Right Side (B)
**
Cabinet Right Side (R)
**
Cabinet Right Side (W)
**
Bottom Support Panel
*
Toothed Bar
*
Plastic Pivot
*
Midrange Cabinet Support
*
Left Cover Clamp
*
Right Cover Clamp
Left Plastic Lateral
Right Plastic Lateral
Nylon Board Spacer
110614
770844
110320
340916
171638
770839
768198
230565
140010
020493
010545
Mains Socket
Power Switch & Cables Assembly
*
Power Switch
Button for Power Switch
Mains Switch Support
Mains Cables Assembly
Mains Filter Board (Pcb#310643)
*
2.5mH 250V 3A AC Line Filter
*
3 Contacts P=10 Vert Terminal Block
*
100n 250Vac MKP EMI Capacitor “Siemens”
*
4n7 250V Ceramic Capacitor (Iec-Ul-Csa)
Mains Assembly
Transformer Assembly
730453
730470
340329
230130
230131
190133
140036
*
*
**
**
**
**
**
Transformer Assembly 230Vac (EU)
Transformer Assembly 115Vac (US)
Rubber Bush
Transformer 230Vac 220W (EU)
Transformer 115Vac 220W (US)
Lateroid Insulator For Screw Block
Screw Block (specify contacts)
731004
340154
340079
340078
230527
230524
171660
171659
141101
141010
140929
140917
140908
140010
110119
100965
100900
100045
100043
090183
080605
080171
080156
080103
030950
030929
030880
030856
030555
110020
110010
110083
110021
Power Amplifier & Supply Board (Pcb#310604)
*
TO3/TO218 Mica Washer
*
TO220 Mica Washer
*
TO220 Insulated Bush
*
BL02RN2-R62 EMI Coil For Signal
*
100uH Switching Coil
*
Right Support Board
*
Left Support Board
*
4 Contacts Vert Male Connector
*
4 Contacts Vert Female Connector
*
9 Contacts Vert Male Connector
*
2 Contacts Vert Male Connector
*
6 Contacts Vert Male Small Connector
*
3 Contacts P=10 Vert Terminal Block
*
Fuse Clip 10A max (EU) (US)
*
TDA7294 70W Audio Amplifier with Mute
*
L4960 5-40V 2.5A Switching Regulator
*
7812 +12V 1A Voltage Regulator
*
7912 -12V 1A Voltage Regulator
*
BC550 TO92 LN Npn Transistor
*
KBL02 4A 200V Rectifier Diode Bridge
*
FE6B 6A 100V Fast Recovery Diode
*
1N4002 1A 100V Rectifier Diode
*
1N4148 100mA 75V Signal Diode
*
470u 16V 20% Low Esr Vert Electrolytic Capacitor
*
4u7 35V 20% Electrolytic Tantalium Capacitor
*
10000uF 25V Snap-In Electrolytic Capacitor
*
4700uF 25V Snap-In Electrolytic Capacitor
*
4700u 50V 20% Snap-In Electrolytic Capacitor
T5A Fuse 5x20mm (EU)
T2A Fuse 5x20mm (EU)
T2A Fuse 6.3x32mm (US)
T5A Fuse 6.3x32mm (US)
770846
141107
141105
140327
730994
230533
141101
Cross-Over Cables Assembly
*
4 Contacts Female Connector Housing
*
Female Crimping Contact
*
6 Contacts Hor Male Connector
Cross-Over Board (Pcb#310606)
*
0.45mH 1mm Crossover Coil
*
4 Contacts Vert Male Connector
Power Amplifier & Supply Board
Cabinet Speakers Assembly
J 20
710514
770845
141107
141105
510246
229015
220117
Mid-Speaker Box Assembly
*
Mid-Speaker Cables Assembly
**
4 Contacts Female Connector Housing
**
Female Crimping Contact
*
Midrange Box
*
8ohm 20W 1" Dome Tweeter Speaker
*
8ohm 5" Woofer Speaker
731024
141011
141010
140935
140918
140889
140872
110305
106007
100919
090183
080241
080156
080103
Mixer & Phones Amp. Board (Pcb#310658)
*
6 Contacts Vert Female Connector
*
4 Contacts Vert Female Connector
*
6 Contacts Hor Male Connector
*
2 Contacts Hor Male Connector
*
Dual In Line Vert Male Strip (specify contacts)
*
4 Contatcs Hor Male Connector
*
Relay 12V / 2 Switch 1A 250V
*
TDA8542AT SOIC 2X1.5W BTL Audio Amplifier
*
MC33078 Dual LN Operational Amplifier
*
BC550 TO92 LN Npn Transistor
*
5V6 1W 5% Zener Diode
*
1N4002 1A 100V Rectifier Diode
*
1N4148 100mA 75V Signal Diode
731018
731007
230569
140872
140217
140207
120849
652854
171327
Phones Assembly
*
Phones Board (Pcb#310513)
**
FL5R200PNT EMI Coil For Signal
**
4 Contatcs Hor Male Connector
**
Jack Slim Horizontal S-F Socket
**
Jack Horizontal F Socket (with dual switch)
**
Hor Pc Male Faston 2.8
*
Phones Board Support
*
Phones Board Fixing
Mixer & Phones Amp. Board
Phones Assembly
Keyboard Assembly
720568
840762
840761
761173
141018
141011
140918
100740
100605
050493
050492
050414
010725
010662
010661
720559
840738
810552
340764
340211
141018
141010
080103
810551
340212
340211
141018
141010
080103
500074
160214
160213
151226
151225
151224
151223
151222
151221
151220
151219
151218
151217
340092
210017
Keyboard Assembly (TP10MDS)
*
20 Wires 25cm Length Flat Cable
*
20 Wires 12.5cm Length Flat Cable
*
Keyboard Interface Board (Pcb#315024)
**
20 Contacts Vert Female Connector
**
6 Contacts Vert Female Connector
**
2 Contacts Hor Male Connector
**
HD6433278 Cpu F=20MHz
**
74HC125 Quad 3-State Buffer
**
10Kx4 1/8w 5% Resistor Array
**
10Kx8 1/8w 5% Resistor Array
**
2K2x4 1/8w 5% Resistor Array
**
20MHz Ceramic Resonator With Capacitors
**
220p 10% 50V X8 Cap Array
**
47p 10% 50V X8 Cap Array
*
Keyboard Assembly (TP10MDS)
**
4 Wires 5cm Length Flat Cable
**
39 Contacts L Board For Dynamic Keyb. (PCB#310531)
*** 3 Dual Contacts Rubber Strip
*** 12 Dual Contact Rubber Strip
*** 20 Contacts Vert Female Connector
*** 4 Contacts Vert Female Connector
*** 1N4148 100mA 75V Signal Diode
**
49 Contacts R Board For Dynamic Keyb. (PCB#310530)
*** 13 Dual Contact Rubber Strip
*** 12 Dual Contact Rubber Strip
*** 20 Contacts Vert Female Connector
*** 4 Contacts Vert Female Connector
*** 1N4148 100mA 75V Signal Diode
**
Mechanicals Parts (TP10MDS)
*** Sharp Key Return Spring (TP10MDF/s)
*** Natural Key Return Spring (TP10MDF/s)
*** Last C Key (TP10MDS)
*** First A Key (TP10MDS)
*** Sharp Key (TP10MDS)
*** B Key (TP10MDS)
*** A Key (TP10MDS)
*** G Key (TP10MDS)
*** F Key (TP10MDS)
*** E Key (TP10MDS)
*** D Key (TP10MDS)
*** C Key (TP10MDS)
*
5mm Board Spacer
*
2x10mm Adhesive Black Felt (specify mt)
Controls Panel Assembly
820585
820584
810678
Controls Panel Assembly (Gem)
Controls Panel Assembly (Baldwin)
*
Controls Panel & Display Board Assembly
731001
141018
140918
140529
100606
090194
080752
080724
080103
070551
731000
141018
140918
140874
090194
080754
080103
660594
660593
653420
653419
653417
653416
653414
653413
652735
340915
340820
340523
340512
210258
210020
210017
**
***
***
***
***
***
***
***
***
***
**
***
***
***
***
***
***
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Controls Panel Board (Pcb#310622)
20 Contacts Vert Female Connector
2 Contacts Hor Male Connector
Microswitch 12V 50mA 0.25mm
74HC138 1 Of 8 Decoder
BC560 TO92 LN Pnp Transistor
Led 3mm Wide Diffused Red
Led 3mm 40deg High Eff Green
1N4148 100mA 75V Signal Diode
10K Linear 30mm Slider Potentiometer
Display Board (Pcb#310637)
20 Contacts Vert Female Connector
2 Contacts Hor Male Connector
Single In Line Vert Male Strip (specify contacts)
BC560 TO92 LN Pnp Transistor
LMC97S005A Lcd Display 128X64 dots
1N4148 100mA 75V Signal Diode
Controls Panel (Gem)
Controls Panel (Baldwin)
<+ -> Rubber Pad
<< >> Rubber Pad
2+4+8+8 Rubber Pad
5+5+2 (PLAY-REC) Rubber Pad
5+5+2 (SPLIT-PERF) Rubber Pad
4+1 Rubber Pad
Display Screen
LED Lens
Slider Knob
6.5mm Spacer
Slider Potentiometer Guide
Slider Potentiometer Felt
1.5x12mm Adhesive Red Felt (specify mt)
2x10mm Adhesive Black Felt (specify mt)
761172
761189
560021
560020
141018
141012
141011
141010
140874
110282
106003
106001
105009
105006
104041
104030
104023
104046
104014
104000
103012
103010
103009
103004
103002
103001
091001
091000
081204
081000
055101
055100
011501
011500
010727
010704
110282
CPU & Sound Generator Board (Pcb#310603)
CPU & S.G. Board (Pcb#310661) limited edition for 104046
see schematics for explanation about limited edition.
*
GAL 16V8C-7 Programmed Disp3 Ram Read
*
GAL 16V8C-7 Programmed Disp3 Ram Write
*
20 Contacts Vert Female Connector
*
8 Contacts Vert Female Connector
*
6 Contacts Vert Female Connector
*
4 Contacts Vert Female Connector
*
Single In Line Vert Male Strip (specify contacts)
*
3.6V 60mAh Nicd Battery
*
MAX709 Power Monitor With Reset
*
MC33078P SOIC Dual Low Noise Op. Amp.
*
DISP3 QFP Digital Sound Processor (Hitachi)
*
HD6413003F16 QFP Cpu
*
23C64000G SOP 64MBit Rom Wave98
*
AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS
*
23C32000G SOP 32Mbit Rom “ProWave3”
*
32Mbit Rom “ProWave3” limited edition for pcb#310661
*
HN624316FBC30 SOP 16Mbit Rom “Library”
*
HM628128LFP5 SOP 1Mbit Static Ram Ta=55nS
*
74HC125D SOIC Quad Tri-State Buffer
*
74HC04D SOIC Hex Inverter
*
74HC02D SOIC Quad 2-In Nor Gate
*
AD1865R SOP 18bit D/A Converter
*
74HC245DW SOIC Octal Bus Transceiver
*
74HC08D SOIC Quad 2-Input And Gate
*
BC857 TO236 Smd Pnp Transistor
*
BC847 TO236 Smd Npn Transistor
*
5.6V 0.5W Zener
*
PMLL4148 Smd 100mA 75V Signal Diode
*
4K7 X4 1/16w 5% Smd Resistor Array
*
100E X4 1/16w 5% Smd Resistor Array
*
220pF x4 10% 100V NP0 Smd Capacitor Array
*
47pF x4 10% 100V NP0 Smd Capacitor Array
*
45.1584MHz Quartz Resonator
*
16MHz Quartz Resonator
*
3.6V 60mAh Nicd Battery
730996
730995
230569
230527
141012
141010
140918
140908
140247
140217
Outputs Assembly
*
Outputs Board (Pcb#310608)
**
FL5R200PNT EMI Coil For Signal
**
BL02RN2-R62 EMI Coil For Signal
**
8 Contacts Vert Female Connector
**
4 Contacts Vert Female Connector
**
2 Contacts Hor Male Connector
**
6 Contacts Vert Male Small Connector
**
8 Poles Mini Din Female Socket
**
Jack Slim Horizontal S-F Socket
CPU & Sound Generator Board
Outputs Assembly
140216
140212
120857
100734
100602
100035
090194
090183
080103
653440
210018
171329
**
**
**
**
**
**
**
**
**
*
*
*
6 Poles Din Horizontal Female Socket
5 Poles Din Horizontal Female Socket
Vertical Male Faston 6.3mm
MAX202E RS232 Drivers/Receiver
74HC04 Hex Inverter
6N138 Optocoupler
BC560 TO92 LN Pnp Transistor
BC550 TO92 LN Npn Transistor
1N4148 100mA 75V Signal Diode
Outputs Panel
1x5mm Adhesive Red Felt (specify mt)
Support for Outputs Panel
841182
841181
841178
841176
841057
841043
841038
841036
841010
840844
840810
840799
840792
840782
840767
9 Wires 25cm Length Flat Cable
6 Wires 15cm Length Flat Cable
6 Wires 35cm Length Flat Cable
20 Wires 48cm Length Flat Cable (3 Connectors)
4 Wires 60cm Length Crimp Terminal Cable
2 Wires 35cm Length Crimp Terminal Cable
8 Wires 25cm Length Flat Cable
6 Wires 45cm Length Flat Cable
2 Wires 50cm Length Crimp Terminal Cable
2 Wires 7.5cm Length Crimp Terminal Cable
4 Wires 30cm Length Flat Cable
4 Wires 7.5cm Length Flat Cable
4 Wires 35cm Length Flat Cable
6 Wires 35cm Length Flat Cable
2 Wires 30cm Length Crimp Terminal Cable
Wiring Connections
Updating Software Board
751180
550657
Updating Software Board (Pcb#315166)
Eprom with Last Software Version for RP90-100-150 Digital
Piano
550658
Eprom with Last Software Version for RP200 GRP300 Digital
Piano
Note:
Each spare part is single quantity unless otherwise specified.
Asterisk prefix explanation:
Omitted
= First level spare part.
One asterisk = Second level, part of previous listed first level part.
Two asterisk = Third level, part of previous listed second level part.
Three asterisk = ............
Any request for not above mentioned part must encompass specific
description including:
1)
2)
3)
4)
5)
Model name,
Section name,
Module code,
Reference name,
Quantity number.