Fender Super Champ X2 Service manual

SUPER CHAMP X2 COMBO/ HEAD™

(This is the model name for warranty claims)

COMBO p/n 2223000000 (120V)

HEAD p/n 2223100000 (120V)

SERVICE MANUAL

ATTENTION:

WARRANTY SERVICE PROCEDURES

The Super Champ X2 Combo and Head are considered to be field serviceable to the component level. Except for the µDSP PCB which must be replaced as a complete module. We do however understand that some circumstances may require replacement of other PCB Assemblies. Any Fender Authorized Service Center in need of a warranty replacement PCB Assembly for this unit should contact FMIC Tech Support by phone at

(866) 345-3642 or email: [email protected]

Fender Musical Instruments Corporation, 17600 North Perimeter Drive, Suite 100 Scottsdale, AZ 85255

Issued: March 2012

2

SUPER CHAMP X2 COMBO/HEAD™


IMPORTANT NOTICE



Copyright © 2012 FMIC. All rights reserved. All information contained herein is CONFIDENTIAL and PROPRIETARY and is the property of Fender® Musical Instruments Corporation. It is not to be sold or assigned to another party and is disclosed solely for use by Fender Authorized

Service Centers for purposes of product service and maintenance. All information is not to be disclosed to others without the expressed permission of Fender® Musical Instruments Corporation. All specifications are subject to change without notice. This information and any copies produced electronically or otherwise must be surrendered upon demand of Fender® Musical Instruments

Corporation.



Parts marked with two asterisks ( ** ) indicate the required use of that specific part. This is necessary for RELIABILITY and SAFETY requirements.

DO NOT USE A SUBSTITUTE!

PARTS LIST CODES

The description codes used in the itemized Parts Lists are defined below:

CAPACITOR CODES

CAP AE = Aluminum Electrolytic

CAP CA = Ceramic Axial

CAP CD = Ceramic Disk

CAP CR = Ceramic Radial

CAP MPF = Metalized Polyester Film

CAP MY = Mylar

CAP PFF = Polyester Film/Foil

RESISTOR CODES

RES CC = Carbon Comp

RES CF = Carbon Film

RES FP = Flame Proof

RES MF = Metal Film

RES MOX = Metal Oxide

RES WW = Wire Wound

HARDWARE CODES

BLX = Black Oxide

CR

HWH

=

=

Chrome Plated

Hex Washer Head

M

NI

OHP

PB

PHP

PHPS

SMA

SMB

SS

TF

ZI

=

=

=

=

=

=

=

=

=

=

=

Machine Screw

Nickel Plated

Oval Head Phillips

Particle Board

Pan Head Phillips

Pan Head Phillips Sems

Sheet Metal "A" Point

Sheet Metal "B" Point

Stainless Steel

Thread Forming

Zinc Plated

3



SPECIFICATIONS

Model Name:

Release Number:

Part Numbers

Power Requirement:

Power Output:

Power Amp Sensitivity:

Impedances

Speaker Complement:

Footswitch

Dimensions

Weight:

(120V, 60Hz) US:

(230V, 50Hz) EUR:

(230V, 50Hz) UK:

(240V, 50Hz) AUS:

(100V, 50Hz) JPN:

(220V, 50Hz) ROK:

(240V, 50Hz) ARG:

(110V, 50Hz) TW:

Input (Pre-Amp):

Effects Send:

Effects Receive:

SUPER CHAMP X2 COMBO/ HEAD

PR 2259 PR 2260

HEAD

2223000000

2223006900

2223004900

2223003900

2223007900

2223009900

2223005900

2223001900

90 W

15 W RMS into 8 ohms @ 10 %THD

10mV for 10 W into 8 ohms @ 5 %THD

>1M Ohms

1 kOhm

10 kOhm

Fender Special Design 8 ohm, 10”

(P/N 0091245000)

2 Button DC Footswitch Assy

(P/N 0071359000)

Height:

Width:

Depth:

15 in ( 38 cm)

17.5 in ( 45 cm)

9 in ( 22.9 cm)

24 lbs (10.9 kg)

Product specifications are subject to change without notice

COMBO

2223100000

2223106900

2223104900

2223103900

2223007900

2223009900

2223005900

2223001900

4



SERVICE NOTES

1. CHASSIS REMOVAL is accomplished by first removing the COMBO or HEAD’s cabinet’s back panel. Then remove the four (4) screws from the top of the cabinet that secure the chassis. Disconnect the ¼” speaker plug from the speaker jack (COMBO only). Then slide the chassis toward the rear of the cabinet.

2. MAIN PCB REMOVAL is accomplished by removing the IEC Connector, the fuse holder, the speaker jack nut, the line out jack nut and the two screws that hold the chassis’ rear panel to the chassis. Remove the rear panel and the vacuum tubes. Disconnect the ribbon cable that goes between the main PCB and the uDSP

PCB. Remove all screws holding the main PCB to the stand offs on the chassis. Then remove the front panel knobs and the nuts holding the controls to the front panel. Slide the front panel

PCB back away from the front panel. Remove all the fast-ons connecting the main PCB to the power indicator, the power transformer and the output transformer. Now the main PCB can be lifted up and out of the chassis taking advantage of the slots in the back of the chassis.

3. The COMBO and the HEAD share the same chassis and circuitry. The combo contains a captive 10” speaker while the head can be used with any suitable speaker cabinet such as the

SC112 enclosure.

PCB EXCHANGE POLICY

Parts marked with a single asterisk ( * ) in the Part

Lists are not field replaceable. If a failure due to one of these components is detected, please contact the FMIC Customer Service Department to order the complete PCB Assembly.

CIRCUIT DESCRIPTION

This section provides concise information about new or unusual circuitry designs incorporated into this amplifier model. The purpose is to aid the service technician by providing insight into the design areas most likely to become obstacles in troubleshooting. Information is focused for its effective use while maintaining the security of Fender® proprietary information whenever possible.

MAIN PCB

The Main PCB Assy. contains the circuitry for the pre-amplifier, the power amplifier, and the power supply. The controls are located on a breakaway section of the main PCB with ribbon cables connecting them.

PRE-AMPLIFIER

Op-amp U6-A provides the high impedance instrument input with 14db of gain. Op-amp U6-B is configured as an active filter producing high frequency pre-emphasis. U1-A provides another 20db of gain. Its’ output is clamped to +/-2V. The uDSP

PCB Assy. chooses either the low gain output from

U6-B or the higher gain output from U1-A depending on the amplitude of the guitar input signal. Opamp U3-A is configured as a differential input amp recovering the signal after uDSP processing and conversion back to an analog signal. The LOUT and

.

5



ROUT signals are the input to the differential amp which acts as a three pole active low pass filter for de-emphasis. The output of U3-A is applied to a buffer amp U1-A which drives op-amp U1-B which provides the LINE OUT signal and the power amp input. FET Q-1 provides system muting during power up/down in conjunction with the power sense circuits composed of D9, Q2, and Q4.

USER INTERFACE

The 4 – 16 position encoders (S2 – S3) for the

VOICE and EFFECT SELECT are sent to the GPIO buss of the uDSP and polled at a 1000Hz rate.

The 6 potentiometers CH1 VOLUME (R85), CH2

VOLUME (R83), CH2 GAIN (R84), TREBLE (R82),

BASS (R81), and AND FX LEVEL (R80) generate

DC Voltages (0.0V to +3.3V) that are polled at a

1000Hz rate by the uDSP’s A/D converter.

POWER AMPLIFIER

The power amplifier consists of V1, V2, and V3. T2 and associated circuitry. The signal is fed to the gate of V1-B in common cathode configuration. The signal is then fed from the plate of V1-B to the gate of V1-A which is operating as a phase splitter driving V2 from its’ plate and V3 from its’ cathode. V2 and V3 are operating in Class A-B push-pull mode.

T2 matches the impedance of V2’s plate to the 8

Ohm speaker. Negative feedback is provided by

R23 feeding signal back to V1B’s cathode.

µDSP PCB

The µDSP PCB is located in the back of the chassis opposite the power transformer. It provides the amplifier voicing and effects functions. The µDSP PCB is not field serviceable and must be replaced as an assembly.

USB PCB

The USB PCB provides the USB interface to the

µDSP and ESD protection. The USB interface is used to communicate between the user’s computer for the purpose of altering the amp’s presets or restoring the amp to factory settings.

POWER SUPPLY

T1 has four secondary windings for the +5V regulator, the +/-12V supplies, the tube filaments and the high voltage supply. The violet winding is rectified by a fullwave bridge, filtered by C41 and fed to the

µDSP PCB where it is regulated to +3.3VDC and fed back on to the main PCB. Similarly, the center tapped orange and yellow winding is rectified, filtered and fed to +/-12V zeners to provide power to the operational amplifiers and other circuitry. The red windings provide the high voltage for the vacuum tubes. The green winding provides 6.3VAC for the vacuum tube filaments. A voltage doubler is employed to produce -41.9VDC to bias the output tubes, V2 and V3.

6



.PARTS LIST: MAIN PCB ASSEMBLY

QTY. PART # DESCRIPTION

1 0091225000 *MAIN PCB ASSY SCX2

1 0027353001 RES FILM 1W 100kohm 5%

1 0091199001 RES MOX FP 1W 5% 7.5ohm

1 0033095001 RES MOX FP 1W 5% 1ohm LL

2 0036351001 RES MOX 2W 100ohm 5%

1 0036921001 RES MOX 2W 1k 5%

1 0041268001 RES MOX 2W 10k 5% LL

REFERENCE DESIGNATION

STUFFED MAIN PCB

R21

R64

R20

R87-88

R79

R47

2 0028021001 RES MOX 2W 470ohm 5%

1 0053860000 CAP MPF .1uF 275V 10%

1 0038699001 CAP CA 100pF 100V 5%

10 0039263001 CAP CA 1000pF 50V 5%

R4 R25

C58

C21

C7 C14 C29-35 C47

2 0039270001 CAP CA 10000pF 50V 5%

2 0038703001 CAP CA .1uF 50V 10%

1 0039267001 CAP CA 3900pF 100V 5%

4 0038698001 CAP CA 47pF 100V 5%

C4 C11

C22-23

C15

C24 C26 C66 C72

2 0051457003 CAP CD 100pF 500V NPO 5% C13 C25

4

1

0

17

0051406003 CAP CD 220pF 500V 10%

0051458003 CAP CD 470pF 500V 10%

0034788003 CAP CR .1uF 50V 20% .2"

0034788003 CAP CR .1uF 50V 20% .2"

1 0064089001 DIODE 1N4003

6 0026730001 DIODE 1N4006 800V 1A

2 0006260001 DIODE 1N4448 SIGNAL

8 0064089001 DIODE 1N4003

2 0054210001 DIODE SCHOTTKY BAT85

2 0029690001 DIODE HV 3kV 200mA

1 0031017001 DIODE ZEN 1N5223B 2.7V 5%

1 0027327001 DIODE ZEN 1N5234B 6.2V 5%

1 0029898001 DIODE ZEN 1N5236B 7.5V 5%

C1-3 C65

C43

C9-10 C18-19 C48 C44 C39 C49-51 C54-

55 C68-70 C73 C76

D3

D6-8 D12-14

D10-11

D17-21 D23-24 D27

D15-16

D1-2

D4

D9

D5

2 0047140060 DIODE ZEN 1N5349B 12V 5W 5% D25-26

2 0038690001 CAP AE AX 1uF 100V 20% C28 C67

6 0038692001 **CAP AE AX 10uF 35V 20%

1 0009512001 CAP AE AX 22uF 25V 20%

C12 C27 C42 C45-46 C77

C8

2 0028471003 **CAP AE RDL 47uF 50V 20% C59 C62

2 0028476003 **CAP AE RDL 100uF 50V 20% C16-17

2 0028494000 **CAP AE RDL 1000uF 35V 20% C57 C60

3 0054204000 **CAP AE RDL 22uF 450V 20% C38 C40-41

1 0055992000 **CAP AE RDL 4700uF 16V 20%

8 0026000001 FSTN TAB MALE PCB MT .187

C53

P1-4 P6-8 P18

10 0025802000 FSTN TAB MALE .250x.032 P

1 0027255003 CAP MPF .001uF 100V 10%

P9-14 P16 P19-21

C36

* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.

shaded Unique Fender® part. Order directly from the FMIC Parts Department.

shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.

** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.

shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.

7



2 0073586001 **FUSE QA AXIAL LEAD 1A 125V

1 0075607001 **FUSE QA 2A 125V

1 0070334001 **FUSE QA AXIAL LEAD 7A 125V

2 0026368001 RES CF 1/2W 100ohm 5%

1 0027871001 RES CF 1/2W 1Kohm 5%

1 0053869001 RES CF 1/2W 1 MEG 5%

1 0026549001 RES CF 1/2W 5% 1.5kohm

F4-5

F3

F2

R22 R24

R13

R14

R16

1 0037169001 RES CF 1/2W 1.8k 5%

2 0025117001 RES CF 1/2W 220k 5%

1 0026493001 RES CF 1/2W 2.7Kohm 5%

1 0025109001 RES CF 1/2W 47ohm 5%

2 0047434001 RES CF 1/2W 56k 5%

1 0091202000 HDR 2MM VERT 8X2 CKT

1 0091201000 HDR 2MM VERT 25X2 CKT

REF 0055959000 HDR .1 CTR 7x2 CKT SQ PIN

R86

R2-3

R23

R17

R12 R15

P15

P5

P17

8 0057350000 HEADER .1 CTR 8x2 CKT SQ

2 0053450000 JACK STEREO R/A

P22-P29

J1-2

2 0059889000 JACK STEREO R/A W/MTL BUSH J3-4

3 REF JUMPER WIRE 22GA JMP1-3

2 0049948000 LED RED LONG LEAD

3 0027278003 CAP MPF .1uF 63V 10%

D22 D28

C52 C63-64

2 0027267003 CAP MPF .022uF 100V 10% C37 C71

1 0024833000 CAP MPF RDL .022uF 400V 10% C20

3 0024855000 CAP MPF RDL .1uF 630V 10% C5-6 C61

6 0027941000 CONTROL SNAPIN 50k B TAPER R80-85

1 0027873000 CONTROL PCB MNT LIN 30% 25K

12 0024952001 RES CF 1/4W 100ohm 5%

4 0024965001 RES CF 1/4W 1k 5%

7 0024981001 RES CF 1/4W 10k 5%

2 0024997001 RES CF 1/4W 100k 5%

2 0025069001 RES CF 1/4W 1M 5%

1 0025084001 RES CF 1/4W 10M 5%

1 0024969001 RES CF 1/4W 1.5k 5%

2 0024985001 RES CF 1/4W 15k 5%

1 0029005001 RES CF 1/4W 2k 5%

2

5

1

2

4

0029006001 RES CF 1/4W 20k 5%

0024956001 RES CF 1/4W 220ohm 5%

0024973001 RES CF 1/4W 3.3k 5%

0024975001 RES CF 1/4W 3.9k 5%

0024947001 RES CF 1/4W 47ohm 5%

R6

R49 R58 R60-61 R66 R68-70 R77-78 R92

R100

R1 R51 R89-90

R5 R9 R44 R50 R54 R62-63

R32 R41

R43 R52

R45

R34

R7 R26

R91

R29 R31

R11 R33 R67 R95 R106

R10

R27 R42

R65 R71 R102-103

12 0024993001 RES CF 1/4W 47k 5%

1 0028034001 RES CF 1/4W 5.1Kohm 5%

4 0024994001 RES CF 1/4W 56k 5%

1 0024995001 RES CF 1/4W 68k 5%

0 0024996001 RES CF 1/4W 82k 5%

R18-19 R28 R35-36 R46 R48 R72-76

R8

R37-40

R30






8



3 0015718001 RES MF 1/4W 1% 1k

2 0015582001 RES MF 1/4W 10k 1%

1 0016951001 RES MF 1/4W 1% 1.21k

2 0025811001 RES MF 1/4W 5.11k 1%

2 0016946001 RES MF 1/4W 1% 825ohm

1 0016739003 XSTR NPN 2N4401 TO-92

2 0016742003 XSTR PNP 2N4403 TO-92

R53 R55 R93

R59 R96

R97

R56 R101

R57 R94

Q4

Q1-2

1 0014689003 XSTR N-CH JFET J111 TO-92 Q3

1 0028091000 SWITCH PUSH SLFLK SHORT STROKE

1 0071228000 SWITCH PUSH MOMENTARY S4

2 0063204000 ENCODER 16-POS 4-BIT GREY CODE S2-3

2 0091200003 CAP TAN RDL 22uF 16V 20%

2 0031611000 IC DUAL OP-AMP PC4560

C56 C74-75

U2 U5

1 0091208000 IC REGULATOR +3.3V LM1117T-3.3 U4

3 0016795000 IC DUAL OP-AMP TL072 U1 U3 U6

1 0029167000 TUBE SOCKET 9 PIN PCB MOUNT

2 0059847000 TUBE SOCKET VT8-PT

For V1

FOR V2-3

1 0066390000 **HEATSINK TO-220 .5x.75x0.375" BLACK

1 0039420000 SCRW M 4-40x3/8PHP SS SE

1 0097360000 NUT HEX 4-40 EX LOCK

8 0031184000 SCRW M 6-32x1/4 PHP BLX ITLW

4 0053931000 STANDOFF 6-32X9/16X1/4 AL RND

2 0015585001 RES MF 1/4W 1% 100K

1 0055812000 LED TULIP ASSEMBLY

R 98-99

.PARTS LIST: USB PCB ASSEMBLY

1 0091226000 *PCB ASSY SUPER CHAMP X2 USB

1 0055959000 HEADER .1 CTR 2X7 CKT SQ PIN

1 0091203000 US-TPD2E001

1 0091204000 USB CONNECTOR

STUFFED PCB ASSY

.PARTS LIST: CHASSIS ASSEMBLY

1 0091223000 *PANEL FRONT SC X2

1 0091224000 *PANEL REAR SC X2 COMBO 120V

0091317000 *PANEL REAR SC X2 COMBO 230V

0092403000 *PANEL REAR SC X2 COMBO 220V CN

1 0091225000 *PCB ASSY SC X2 MAIN

1 0091226000 *PCB ASSY SC X2 USB

2 0031153000 WSHR FLAT 3/8x.614 NI

2 0016352000 NUT HEX 3/8-32x3/32 TK NI

1 0092163000 *PCB ASSY UNIVERSAL DSP56725

2 0078304000 STANDOFF NYLON 7MM W/3MM DIA


2 0014345000 SCRW M 4-40x3/16 PHP BLX

STUFFED µDSP PCB ASSY






9



2 9302110021 TUBE 6V6-C GT-6V6-C

1 0013341000 TUBE 7025/12AX7A 12AX7B SILVER

2 0020424000 TUBE RING UNIVERSAL (277H-2)

2 0057256000 KNOB ROTARY ARROW W/CHRM

6 0054419000 KNOB ROTARY 180 SS W/CHR

1 0091234000 **XFMR PWR 120V SUPER CHAMP X2

0091235000 **XFMR PWR 100V SUPER CHAMP X2



4 0022004000 NUT KEPS #8-32 ZINC

1 0091237000 **XFMR OUTPUT SUPER CHAMP X2

2 0028684000 SCRW SMB 6x3/8 PHP BLX

1 0054798000 JEWEL ASSEMBLY LED

1 0031625000 NUT HOLDER PILOT LIGHT 11/16-27

1 0031263000 BUSHING SNAP SHORT 3/4X15/16 BLK

1 0036702000 **FUSE HOLDER 3AG FINGER GRIP

0036703000 **FUSE HOLDER 5MM FINGER GRIP

1 0039287000 **SWITCH DPST .187 TAB GLOB

1 0054642000 **CONNECTOR IEC SNAP IN

2 0048451000 BUTTON PUSH OFF WHITE

1 0038900000 SCRW TF 6-32X1/4 PHP ZI

2 0055838000 NUT PLASTIC BLK REAN JACK

1 0091238000 **GASKET O/P XFMR SUPER CHAMP XD

1 0077982000 **FUSE QA 1-1/4X1/4 250V 3A

0020793000 **FUSE QA 20mmx5mm 250v 1.6A

4 0070206000 CABLE RIBBON 16 CKT W/2 CONN 3"

1 0091223000 *PANEL FRONT SUPER CHAMP X2

1 0091224000 *PANEL REAR X2 COMBO 120V

0091317000 *PANEL REAR X2 COMBO 230V

0092403000 *PANEL REAR X2 COMBO 220V CN

1 0091225000 *PCB ASSY SUPER CHAMP X2 MAIN

1 0091226000 *PCB ASSY SUPER CHAMP X2 USB

2 0031153000 WSHR FLAT 3/8x.614 NI

2 0016352000 NUT HEX 3/8-32x3/32 TK NI

1 0092163000 *PCB ASSY UNIVERSAL DSP56725

2 0078304000 STANDOFF NYLON 7MM W/3MM DIA


2 0014345000 SCRW M 4-40x3/16 PHP BLX

2 9302110021 TUBE 6V6-C GT-6V6-C

1 0013341000 TUBE 7025/12AX7A 12AX7B SILVER

2 0020424000 TUBE RING UNIVERSAL (277H-2)

2 0057256000 KNOB ROTARY ARROW W/CHRM

6 0054419000 KNOB ROTARY 180 SS W/CHR

STUFFED SCX2 MAIN PCB ASSY

STUFFED SCX2 USB PCB ASSY

STUFFED SCX2 µDSP PCB ASSY






10



1 0091234000 **XFMR PWR 120V SUPER CHAMP X2




4 0022004000 NUT KEPS #8-32 ZINC

1 0091237000 **XFMR OUTPUT SUPER CHAMP X2

2 0028684000 SCRW SMB 6x3/8 PHP BLX

1 0054798000 JEWEL ASSEMBLY LED

1 0031625000 NUT HOLDER PILOT LIGHT 11/16-27

1 0031263000 BUSHING SNAP SHORT 3/4X15/16 BLK

1 0036702000 **FUSE HOLDER 3AG FINGER GRIP

0036703000 **FUSE HOLDER 5MM FINGER GRIP

1 0039287000 **SWITCH DPST .187 TAB GLOB

1 0054642000 **CONNECTOR IEC SNAP IN

2 0048451000 BUTTON PUSH OFF WHITE

1 0038900000 SCRW TF 6-32X1/4 PHP ZI

2 0055838000 NUT PLASTIC BLK REAN JACK

1 0091238000 **GASKET O/P XFMR SUPER CHAMP XD

1 0077982000 **FUSE QA 1-1/4X1/4 250V 3A

0020793000 **FUSE QA 20mmx5mm 250v 1.6A

4 0070206000 CABLE RIBBON 16 CKT W/2 CONN 3"

.PARTS LIST: END ITEM ASSEMBLY

1 0050850000 *NAMEPLATE VINTAGE PLASTIC SMALL

2

1

4

4

4

1

4

8

8

1

1

1

1

0051621000 SCRW SMA 2X9/16 FHP NI

0091245000 SPEAKER 10 INCH 8 OHM SC X2

0026577000 SCRW M 10-32 X 1 PHP BLX

0036199000 SCRW M 8-32x1-3/16 OHP BLX CP

0029527000 WSHR FNSH 8-5/8 FLNGD BLX WX

0091227000 **TUBE CAGE SUPER CHAMP X2 COMBO

0047821000 SCRW M 10-32 3/4 THP STL BLX

0022053000 SCRW SMA 6X1-1/4 OHP STL NI

0037215000 WSHR C/SUNK NICKEL #6

0012582000 CLAMP CABLE NYL SCRW MNT 1/4

0029828000 SCRW PB 8x3/4 PHP ZI

0092061000 **CORD PWR W/IEC CONN DOM 2M

0047250000 **CORD PWR W/IEC CONN 250V

0047249000 **CORD PWR W/IEC CONN 230V UK


0057674000 **CORD PWR W/IEC 230V ARG

0053997000 **CORD PWR W/IEC CONN 100V JPN

0064354000 **CORD PWR WOEC 220V CHINA

0038566000 CABLE ASSY SPKR RT ANG 13-1/2"






11



1

2

1

4

4

4

1

4

8

8

1

1

1

1

0050850000 *NAMEPLATE VINTAGE PLASTIC SMALL

0051621000 SCRW SMA 2X9/16 FHP NI

0091245000 SPEAKER 10 INCH 8 OHM SC X2

0026577000 SCRW M 10-32 X 1 PHP BLX

0036199000 SCRW M 8-32x1-3/16 OHP BLX CP

0029527000 WSHR FNSH 8-5/8 FLNGD BLX WX

0091227000 **TUBE CAGE SUPER CHAMP X2 COMBO

0047821000 SCRW M 10-32 3/4 THP STL BLX

0022053000 SCRW SMA 6X1-1/4 OHP STL NI

0037215000 WSHR C/SUNK NICKEL #6

0012582000 CLAMP CABLE NYL SCRW MNT 1/4

0029828000 SCRW PB 8x3/4 PHP ZI

0092061000 **CORD PWR W/IEC CONN DOM 2M


0047249000 **CORD PWR W/IEC CONN 230V UK


0057674000 **CORD PWR W/IEC 230V ARG

0053997000 **CORD PWR W/IEC CONN 100V JPN

0064354000 **CORD PWR WOEC 220V CHINA

0038566000 CABLE ASSY SPKR RT ANG 13-1/2"

.PARTS LIST: COMBO CABINET ASSEMBLY

1 0091222000 *CABINET ASSY SCX2 COMBO

1 0091220007 *CABINET BAFFLE ASSEMBLY

6 0021972000 NUT T 10-32x3/4 STR 3 PRNG BLX

1 0912200014 *CABINET TOP BACK ASSY

1 0026570000 TOLEX "BRAVURA BLACK" BRONCO

2 0091220016 *CABINET BOTTOM BACK ASSY

1 0032524000 HANDLE REINFORCEMENT STEEL

1 0037790000 HANDLE BLACK RIBBED 9.25"

2 0022244000 SCRW M 10-32x1-1/8 OHP NI

2 0025395000 HANDLE CAP 1 HOLE NI (DWG 17420)

2 0011678000 SCRW SMA 8x1-1/2 OHP BLX

2 0029527000 WSHR FNSH 8-5/8 FLNGD BLX WX

4 0041549000 GLIDE CUP PRESS-IN NI PLATED

0.35 0037788000 GRILL CLOTH BLACK/SILVER

COMBO CABINET COMPLETE

.PARTS LIST: HEAD CABINET ASSEMBLY

1 0091526000 *CABINET ASSY SCX2 HEAD COMPLETE SCX2 HEAD CABINET ASSY

1 0091526008 *GRILLE ASSY

0.3 0037788000 GRILL CLOTH BLACK/SILVER

1 0091526007 *BACK ASSY

0.8 0026570000 TOLEX "BRAVURA BLACK" BRONCO






12



2 0021972000 NUT T 10-32x3/4 STR 3 PRNG BLX

1 0032524000 HANDLE REINFORCEMENT STEEL

1 0037790000 HANDLE BLACK RIBBED 9.25"

2 0022244000 SCRW M 10-32x1-1/8 OHP NI

2 0025395000 HANDLE CAP 1 HOLE NI (DWG 17420)

4 0072900000 SCRW SMA 8x1-1/4 OHP BLX

4 0029527000 WSHR FNSH 8-5/8 FLNGD BLX WX

4 0055734000 "RUBBER FOOT 3/4""DIA"

4 0029677000 SCRW SMA 6x1 THP BLX






13



Service Diagram List

Service Diagram COMBINED ............ SUPER CHAMP X2 MAIN PCB

Service Diagram COMBINED ............ SUPER CHAMP X2 USB PCB

Footswitch Assembly ............ 2-BUTTON FOOTSWITCH

Serv ice Diagram (PCB Assembly) ….. ..... 2-BUTTON FOOTSWITCH

P/N 0092801000

Z2259S1_A.sch-1 - Fri Jun 15 09:54:06 2012

Z2259S1_A.sch-2 - Fri Jun 15 09:54:06 2012

Fender Super Champ X2 Service manual

SERVICE MANUAL

Key Features

Related manuals

Frequently Answers and Questions

What is the power output of the Fender Super Champ X2?

What type of speaker does the Fender Super Champ X2 have?

How many channels does the Fender Super Champ X2 have?

Does the Fender Super Champ X2 have a built-in reverb effect?

Who is the Fender Super Champ X2 a good choice for?

Fender Super Champ X2 Service manual

SERVICE MANUAL

Key Features

Related manuals

Gardner Bender

GSW-125BP

Fender

concert-reverb

PROSELECT

ZIP8F10000

DeLOCK

88750

Fender

Roc Pro 700

DeLOCK

88750

Fender

Princeton 65 DSP

Frequently Answers and Questions

What is the power output of the Fender Super Champ X2?

What type of speaker does the Fender Super Champ X2 have?

How many channels does the Fender Super Champ X2 have?

Does the Fender Super Champ X2 have a built-in reverb effect?

Who is the Fender Super Champ X2 a good choice for?