Operation and Service Manual

Operation and Service Manual
Agilent 16338A Test Lead Set
Operation and Service Manual
SERIAL NUMBERS
This manual provides information on operation and service for the 16005B, C, D Kelvin Clip
Leads, 16006A Pin-type Leads, 16007A, B Alligator Clip Leads, and 16143B Mating Cable.
Agilent Part No. 16338-90000
Printed in JAPAN January 2000
Fourth Edition
Notice
The information contained in this document is subject to change without notice.
This document contains proprietary information which is protected by copyright. All rights are
reserved. No part of this document may be photocopied, reproduced, or translated to another
language without the prior written consent of the Agilent Technologies.
Agilent Technologies Japan, Ltd.
Component Test PGU-Kobe
1-3-2, Murotani, Nishi-ku, Kobe-shi,
Hyogo, 651-2241 Japan
Warranty
This Agilent Technologies instrument product is warranted against defects in material and
workmanship for a period of one year from the date of shipment, except that in the case of
certain components listed in this manual, the warranty shall be for the specied period. During
the warranty period, Agilent Technologies will, at its option, either repair or replace products
which prove to be defective.
For warranty service or repair, this product must be returned to a service facility designed
by Agilent Technologies. The Buyer shall prepay shipping charges to Agilent Technologies
and Agilent Technologies shall pay shipping charges to return the product to the Buyer.
However, the Buyer shall pay all shipping charges, duties, and taxes for products returned to
Agilent Technologies from another country.
Agilent Technologies warrants that its software and rmware designed by Agilent Technologies
for use with an instrument will execute its programming instruction when property installed on
that instrument. Agilent Technologies does not warrant that the operation of the instrument,
or software, or rmware will be uninterrupted or error free.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate
maintenance by the Buyer, Buyer-supplied software or interfacing, unauthorized modication
or misuse, operation outside of the environmental specications for the product, or improper
site preparation or maintenance.
No other warranty is expressed or implied. Agilent Technologies specically disclaims the
implied warranties of merchantability and tness for a particular purpose.
Certication
The Agilent Technologies certies that this product met its published specications at the
time of shipment from the factory. Agilent Technologies further certies that its calibration
measurements are traceable to the United States National Institute of Standards and
Technology, to the extent allowed by the Institute's calibration facility, or to the calibration
facilities of other International Standards Organization members.
Exclusive Remedies
The remedies provided herein are the buyer's sole and exclusive remedies. Agilent Technologies
shall not be liable for any direct, indirect, special, incidental, or consequential damages,
whether based on contract, tort, or any other legal theory.
Assistance
Product maintenance agreements and other customer assistance agreements are available for
Agilent Technologies products.
If you need assistance, contact your nearest Agilent Technologies Sales and Service Oce.
Addresses are provided at the back of this manual.
c Copyright 1997,1998,1999,2000 Agilent Technologies Japan, Ltd.
Manual Printing History
The manual printing date and part number indicate its current edition. The printing date
changes when a new edition is printed. (Minor corrections and updates which are incorporated
at reprint do not cause the date to change.) The manual part number changes when extensive
technical changes are incorporated.
November 1991 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : First Edition (part number: 16338-90000)
June 1992 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Second Edition (part number: 16338-90000)
February 1999 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Third Edition (part number: 16338-90000)
January 2000 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Fourth Edition (part number: 16338-90000)
iv
Safety Summary
The following general safety precautions must be observed during all phases of operation,
service, and repair of this instrument. Failure to comply with these precautions or with specic
WARNINGS given elsewhere in this manual violates safety standards of design, manufacture,
and intended use of the instrument.
The Agilent Technologies assumes no liability for the customer's failure to comply with these
requirements.
Do NOT operate in an Explosive Atmosphere
Do not operate the instrument in the presence of ammable gasses or fumes. Operation of any
electrical instrument in such an environment constitutes a safety hazard.
Keep Away from Live Circuits
Operating personnel must not remove instrument covers. Component replacement and
internal adjustments must be made only by qualied maintenance personnel. Do not replace
components with the power cable connected. Under certain conditions, dangerous voltages
may exist even with the power cable removed. To avoid injury, always disconnect power and
discharge circuits before touching them.
Do NOT Service or Adjust While Alone
Do not attempt internal service or adjustment unless another person, capable of turning o
power and capable of rendering rst aid and resuscitation, is present.
Do NOT Substitute Parts or Modify Instrument
Because of the danger of introducing additional hazards, do not substitute parts or perform
unauthorized modications to the instrument. Return the instrument to a Agilent Technologies
Sales and Service Oce for service and repair to ensure the safety features are maintained.
Dangerous Procedure Warnings
Warnings, such as the example below, precede POTENTIALLY DANGEROUS PROCEDURES
throughout this manual. Instructions contained in the warnings must be followed.
Warning
Dangerous voltages, capable of causing death, are present in this
instrument. Use extreme caution when handling, testing, and adjusting
this instrument.
v
Safety Symbols
General denitions of safety symbols used on equipment or in manuals.
Instruction manual symbol: the product will be marked with this symbol when
it is necessary for the user to refer to the instruction manual in order to
protect against damage to the instrument.
Indicates dangerous voltage (terminals fed from the interior by voltage
exceeding 1000 volts must be so marked).
Protective ground terminal. For protection against electrical shock in case of
a fault in the instrument. Used with wiring terminals to indicate the terminal
which must be connected to ground before operating equipment.
Low-noise or noiseless, clean ground (earth) terminal. Used for a signal
common, as well as providing protection against electrical shock in case
of a fault in the instrument. A terminal marked with this symbol must be
connected to ground in the manner described in the installation (Operation)
manual, and before operating the equipment.
Frame or chassis terminal. A connection to the frame (chassis) of the
equipment which normally includes all exposed metal structures.
Alternating current (power line).
Direct current (power line).
Alternating or direct current (power line).
Warning denotes a hazard. It calls attention to a procedure, practice, condition
or the like, which, if not correctly performed or adhered to, could result in
injury or death to personnel.
Caution sign denotes a hazard. It calls attention to a procedure, practice,
condition or the like, which, if not correctly performed or adhered to, could
result damage to or destruction of part or all of the product.
Note denotes important information. It calls attention to a procedure, practice,
condition or the like, which is essential to highlight.
vi
Contents
1. General Information
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the 16338A . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16338A Test Lead Set . . . . . . . . . . . . . . . . . . . . . . . . . .
16005B, C, D Kelvin Clip Leads . . . . . . . . . . . . . . . . . . . . . .
16006A Pin-type Leads . . . . . . . . . . . . . . . . . . . . . . . . . .
16007A, B Alligator Clip Leads . . . . . . . . . . . . . . . . . . . . . .
16143B Mating Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating and Safety Precautions . . . . . . . . . . . . . . . . . . . . . .
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common Specications for the 16005B, C, D, 16006A, 16007A, B, and 16143B
Specications of the 16005B . . . . . . . . . . . . . . . . . . . . . . .
Specications of the 16005C, D . . . . . . . . . . . . . . . . . . . . . .
Specications of the 16006A . . . . . . . . . . . . . . . . . . . . . . .
Specications of the 16007A, B . . . . . . . . . . . . . . . . . . . . . .
Specications for the 16143B . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Performance Characteristics . . . . . . . . . . . . . . . . .
Supplemental Performance Characteristics of the 16007A, B . . . . . . . .
Supplemental Performance Characteristics of the 16005B . . . . . . . . . .
Supplemental Performance Characteristics of the 16005C, D . . . . . . . .
Supplemental Performance Characteristics of the 16143B . . . . . . . . . .
2. Preparation for Use
Introduction . . . . . . . . . . . . . . . . . . .
Initial Inspection . . . . . . . . . . . . . . . . .
Ambient Environmental Considerations . . . . . .
Operating and Storage . . . . . . . . . . . . .
Connecting The Test Leads For Use . . . . . . . .
Conguration of Test Leads with Milliohmmeters .
Connecting with 16143B to 4338A . . . . . . .
Connecting the Test leads to 16143A, B . . . . .
Repackaging the Test Leads . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1-1
1-1
1-1
1-1
1-1
1-2
1-2
1-2
1-2
1-2
1-2
1-3
1-3
1-3
1-3
1-3
1-3
1-3
1-4
1-4
1-4
1-4
1-4
.
.
.
.
.
.
.
.
.
2-1
2-1
2-3
2-3
2-4
2-4
2-5
2-6
2-6
Contents-1
3. Operation
Introduction . . .
SHORT Correction
For 4338A . . .
For 4328A . . .
Shorting Bar . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-1
3-2
3-3
3-3
3-3
Introduction . . . . . . .
16338A Replaceable Parts
16143B Replaceable Parts
16005B Replaceable Parts
16005C Replaceable Parts
16005D Replaceable Parts
16006A Replaceable Parts
16007A Replaceable Parts
16007B Replaceable Parts
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4-1
4-1
4-2
4-2
4-3
4-4
4-5
4-5
4-5
4. Service
Contents-2
Figures
2-1.
2-2.
2-3.
2-4.
3-1.
3-2.
3-3.
4-1.
4-2.
16338A Product Overview . . . . . . . . . . . .
Conguration of Test Leads and Milliohm Meters . .
Connecting 16143B to 4338A . . . . . . . . . . .
Connecting Test leads to 16143A, B . . . . . . . .
Test Leads Features . . . . . . . . . . . . . . .
Making a Shorting Connection for the 16005B, C, D
Making a Shorting Connection for the 16007A, B .
Kelvin Clip Connections . . . . . . . . . . . . .
Kelvin Clip Connections . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2-2
2-4
2-5
2-6
3-1
3-2
3-2
4-3
4-4
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2-3
4-1
4-2
4-2
4-3
4-4
4-5
4-5
4-5
Tables
2-1.
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
Contents of 16338A . . .
16338A Replaceable Parts
Replaceable Parts . . . .
16005B Replaceable Parts
16005C Replaceable Parts
16005D Replaceable Parts
16006A Replaceable Parts
16007A Replaceable Parts
16007B Replaceable Parts
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Contents-3
1
General Information
Introduction
The purpose of this manual is to enable you to use your 16338A Test Lead Set eciently and
condently. This manual contains both general and specic information. To use the 16338A to
perform a specic function (without having to read the entire manual), follow the directions in
\Using the 16338A".
Using the 16338A
The 16338A has been designed to operate specically with the 4338A Milliohmmeter.
To install the 16338A (16005B, C, D 16006A, 16007A, B, and 16143B), turn to Chapter 2.
To operate the 16338A (16005B, C, D 16006A, 16007A, B, and 16143B), turn to Chapter 3.
To order replaceable parts for the 16338A (16005B, C, D 16006A, 16007A, B, and 16143B),
turn to Chapter 4.
Product Description
16338A Test Lead Set
The 16338A contains four types of test leads and a mating cable, which are designed to operate
specically with the 4338A. These test leads can be mixed or matched depending on the type
of sample being tested.
16005B, C, D Kelvin Clip Leads
These test leads are useful when measuring test devices that have thin electrode conductors
(leads). The 16005B, C, D incorporates the four-terminal (Kelvin) connection method for best
low resistance measurement accuracy. The Jaws of the 16005B, C, D are a set of electrically
independent contacts; the current terminal which feeds the test current to the DUT and its
contact design assures accurate measurement down to the lowest resistance range through its
very low contact resistance.
General Information
1-1
16006A Pin-type Leads
The 16006A's probe tip is a voltage terminal and the outer conductor is a current terminal.
The probe tip is spring-loaded, so that both terminals rmly contact the sample under test.
This probe is useful for press-on contact measurements such as printed board conductivity
measurements.
16007A, B Alligator Clip Leads
The 16007A, B are provided for standard four-terminal measurements. Each pair of test leads
has a separate alligator clip voltage and current terminal. The 16007A is furnished with red
covers and the 16007B is furnished with black covers.
16143B Mating Cable
The 16143B has been designed to operate specically with the 4338A. The 16143B used to
connect between the 4338A and test leads furnished the 16338A.
Operating and Safety Precautions
Operating
You need observe only normal precautions in handling and operating the 16338A. Do not
exceed the operating input power level and signal type appropriate to the instrument being
used, refer to your instrument's operation manual.
Caution
Electrostatic discharge (esd) can damage the highly sensitive microcircuits
in your instrument. ESD damage is most likely to occur as the test leads are
being connected or disconnected. Protect them from ESD damage by wearing a
grounding strap that provides a high resistance path to ground. Alternatively,
ground yourself to discharge any static charge build-up by touching the
outer shell of any grounded instrument chassis before touching the test port
connectors.
Never touch the test lead contacts.
Use a work station equipped with an anti-static work surface.
Service
The voltage levels found in these test leads when used with the intended instruments do not
warrant more than normal safety precautions for operator safety. Nevertheless, service should
be performed only by qualied personnel.
1-2
General Information
Specications
This section lists the complete 16338A specications. These specications are the performance
standards and limits against which the 16338A is tested. When shipped from the factory, the
16338A meets the following specications:
Common Specications for the 16005B, C, D, 16006A, 16007A, B, and
16143B
Operating Temperature : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 0 to 55 C
Operating Humidity : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 95% RH (@40 C)
Non-operating Temperature : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 040 to 70 C
Non-operating Humidity : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 95% RH (@40 C)
Specications of the 16005B
Applicable Instrument : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4328A and 4338A
Cable Length : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 40 cm
Weight : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 40 g
Specications of the 16005C, D
Applicable Instrument : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4328A and 4338A
Cable Length : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 40 cm
Weight : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 20 g
Specications of the 16006A
Applicable Instrument : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4328A and 4338A
Cable Length : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 40 cm
Weight : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 15 g
Specications of the 16007A, B
Applicable Instrument : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4328A and 4338A
Cable Length : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 40 cm
Weight : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 20 g
Specications for the 16143B
Applicable Instrument : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4338A
Cable Length : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 60 cm
Weight : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 220 g
General Information
1-3
Supplemental Performance Characteristics
This section gives supplemental performance characteristics. Supplemental performance
characteristics are not specications, but are typical characteristics included as additional
information for the operator. Supplemental performance characteristics are not guaranteed.
Supplemental Performance Characteristics of the 16007A, B
Applicable DUT size
Diameter of DUT's terminals
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
4 mm
Supplemental Performance Characteristics of the 16005B
Applicable DUT size
Diameter of DUT's terminals : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 7.0 mm
Length of DUT's terminals : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 3 mm
Supplemental Performance Characteristics of the 16005C, D
Applicable DUT size
Diameter of DUT's terminals : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 1 mm
Space between DUT's terminals : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2 mm
Length of DUT's terminals : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2 mm
Supplemental Performance Characteristics of the 16143B
Applicable Test Leads
:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
16005A, 16005B, 16005C, 16005D
16006A, 16007A, 16007B
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
1-4
General Information
2
Preparation for Use
Introduction
This chapter explains how to install the 16338A Test Lead Set. The topics covered include
initial inspection, ambient environmental considerations, connecting the test leads for use and
repackaging the test lead set for shipment.
Initial Inspection
These test leads have been carefully inspected electrically and mechanically before being
shipped from the factory. They should be in perfect physical condition, no scratches, dents or
the like, and it should be in perfect electrical condition. Verify this by carefully performing
an incoming inspection to check the test leads for signs of physical damage and missing
contents. If any discrepancy is found, notify the carrier and Agilent Technologies. Your Agilent
Technologies sales oce will arrange for repair and replacement without waiting for the claim
to be settled.
1. Inspect the shipping container for damage, and keep the shipping materials until the
inspection is completed.
2. Verify that the shipping container contains everything shown in Figure 2-1 and listed in
Table 2-1.
3. Inspect the exterior of the contents of the 16338A for any signs of damage.
Preparation for Use
2-1
Figure 2-1. 16338A Product Overview
2-2
Preparation for Use
No.
1
2
3
4
5
6
7
8
Table 2-1. Contents of 16338A
Description
Agilent Part Number
Kelvin Clip Leads (large)
Kelvin Clip Leads (small, red)
Kelvin Clip Leads (small, black)
Pin-Type Probe Leads
Alligator Clip Lead (read)
Alligator Clip Lead (black)
Mating Cable
Carrying Case
16005B
16005C
16005D
16006A
16007A
16007B
16143B
16338-60001
Quantity
2
1
1
2
1
1
1
1
Ambient Environmental Considerations
Operating and Storage
The 16338A must be operated within an ambient temperature range of 0 C to 55 C and relative
humidity up to 95% at 40 C (non-condensing).
The 16338A may be stored within a temperature range of 040 C to +70 , and at a relative
humidity of up to 95% at +40 C (non-condensing).
Preparation for Use
2-3
Connecting The Test Leads For Use
Conguration of Test Leads with Milliohmmeters
Figure 2-2. Conguration of Test Leads and Milliohm Meters
2-4
Preparation for Use
Connecting with 16143B to 4338A
Figure 2-3. Connecting 16143B to 4338A
Preparation for Use
2-5
Connecting the Test leads to 16143A, B
Note
Figure 2-4. Connecting Test leads to 16143A, B
You can use any combination of test lead types with the 16143A, B.
Repackaging the Test Leads
If shipment to a Agilent Technologies service center is required, each test lead should be
repackaged using the original factory packaging materials.
Alteratively, comparable packaging materials may be used. Wrap the test leads in heavy paper
and pack in anti-static plastic packing material. Use sucient shock absorbing material on
all sides of the 16338A to provide a thick, rm cushion and to prevent movement. Seal the
shipping container securely and mark it FRAGILE.
2-6
Preparation for Use
3
Operation
Introduction
This chapter describes using the test leads and correction techniques for these test leads.
Figure 3-1. Test Leads Features
1
2
3
4
Kelvin Clips. These are connected to DUT.
Pin. This is connected to DUT.
Alligator Clips. These are connected to DUT.
Plug. This connecter is connected to the Mating cable.
Caution
To prevent the probes from being damaged, Do not open the jaws of the
16005B more than 7.0 mm.
Operation
3-1
Caution
Avoid applying a high dc voltage (42 V peak max for 4338A, 150 V max for
4328A) between the probes, periodic surge current may damage the input
circuit of the measurement instrument.
SHORT Correction
Figure 3-2. Making a Shorting Connection for the 16005B, C, D
Figure 3-3. Making a Shorting Connection for the 16007A, B
3-2
Operation
For 4338A
1. Connect the test probe clips together as shown in Figure 3-2 and Figure 3-3.
2. Perform SHORT correction on the 4338A. For step-by-step instructions on how to perform
the correction, refer to 4338A Operation Manual.
For 4328A
To verify proper conductivity of the 16338A, perform the following test when you use the
4328A:
1. Connect the test probe clips as shown in Figure 3-2 and Figure 3-3.
2. The 4328A's meter pointer should indicate zero ohms on the 1 m
range.
3. Disconnect the test probe clips. The meter pointer should deect o-scale.
Shorting Bar
The shorting bar must have very low residual impedance, so a high conductivity metal plate
that is not easily corroded to construct the shorting plate. (It must be clean.)
Operation
3-3
4
Service
Introduction
This chapter gives replaceable parts information for the following products:
16338A Test Lead Kit
16143B Mating Cable
16005B Kelvin Clip Lead
16005C Kelvin IC Clip Lead Red
16005D Kelvin Clip Lead Black
16006A Pin-type Probe Lead
16007A Alligator Clip Lead Red
16007B Alligator Clip Lead Black
16338A Replaceable Parts
Table 4-1 lists the replaceable parts for the 16338A . To order a part listed in the replaceable
parts table, quote the Agilent part number, indicate the quantity required, and address the
order to the nearest Agilent Technologies oce.
Table 4-1. 16338A Replaceable Parts
Agilent Part
Number
Qty.
Description
16143-600111
16005-600111
16005-600121
16005-600141
16006-600011
16007-600011
16007-600021
16338-60001
1
2
1
1
2
1
1
1
Mating Cable2
Kelvin Clip Lead3
Kelvin IC Clip Lead Red4
Kelvin IC Clip Lead Black5
Pin-type Probe Lead
Alligator Clip Lead Red
Alligator Clip Lead Black
Carrying Case
1
Agilent internal-only part number.
2
See 16143A Replaceable Parts section for details.
3
See 16005B Replaceable Parts section for details.
4
See 16005C Replaceable Parts section for details.
5
See 16005D Replaceable Parts section for details.
Service
4-1
16143B Replaceable Parts
Table 4-2 lists the replaceable parts for the 16143B. To order a part listed in the replaceable
parts table, quote the Agilent part number, indicate the quantity required, and address the
order to the nearest Agilent Technologies oce.
Table 4-2. Replaceable Parts
Agilent Part
Number
Qty.
Description
16143-600111
16143-04001
0515-0914
1
1
2
Mating Cable2
Cover Top
Screw Mach M320.5
1
Agilent internal-only part number.
2
The whole unit.
16005B Replaceable Parts
Table 4-3 lists the replaceable parts for the 16005B. To order a part listed in the replaceable
parts table, quote the Agilent part number, indicate the quantity required, and address the
order to the nearest Agilent Technologies oce.
Table 4-3. 16005B Replaceable Parts
Agilent Part
Number
Qty.
Description
16005-600111
16005-60010
16005-61602
Service
Kelvin Clip Lead2
Kelvin Clip Assembly
Cable Assembly
1
Agilent internal-only part number.
2
The whole unit (includes the Kelvin Clip Assembly and the Cable
Assembly).
4-2
1
1
1
16005C Replaceable Parts
Table 4-4 lists the replaceable parts for the 16005C. Figure 4-1 shows the connection from the
cable to the clip assembly of the 16005C. To order a part listed in the replaceable parts table,
quote the Agilent part number, indicate the quantity required, and address the order to the
nearest Agilent Technologies oce.
Reference1
Designator
1
2
3
1 Corresponding
2 The
Table 4-4. 16005C Replaceable Parts
Agilent Part
Number
Qty.
Description
16005-60012
16005-60013
0890-1809
16005-61611
1
1
2 cm
1
Kelvin IC Clip Lead Red2
Kelvin IC Clip Assembly Red
Tube Heat Shrinkable Red
Cable Assembly
to designator in Figure 4-1.
whole unit (includes 1, 2 and 3). Agilent internal-only part.
Figure 4-1. Kelvin Clip Connections
Service
4-3
16005D Replaceable Parts
Table 4-5 lists the replaceable parts for the 16005D. Figure 4-2 shows the connection from the
cable to the clip assembly of the 16005D. To order a part listed in the replaceable parts table,
quote the Agilent part number, indicate the quantity required, and address the order to the
nearest Agilent Technologies oce.
Reference1
Designator
1
2
3
Table 4-5. 16005D Replaceable Parts
Agilent Part
Number
Qty.
Description
16005-60014
16005-60015
0890-1808
16005-61601
1
1
2 cm
1
Kelvin IC Clip Lead Black2
Kelvin IC Clip Assembly Black
Tube Heat Shrinkable Black
Cable Assembly
1
Corresponding to designator in Figure 4-2.
2
The whole unit (includes 1, 2 and 3). Agilent internal-only part.
Figure 4-2. Kelvin Clip Connections
4-4
Service
16006A Replaceable Parts
Table 4-6 lists the replaceable parts for the 16006A. To order a part listed in the replaceable
parts table, quote the Agilent part number, indicate the quantity required, and address the
order to the nearest Agilent Technologies oce.
Table 4-6. 16006A Replaceable Parts
Agilent Part
Number
Qty.
Description
16006-600011
1
1
Pin-type Probe Lead
Agilent internal-only part number.
16007A Replaceable Parts
Table 4-7 lists the replaceable parts for the 16007A. To order a part listed in the replaceable
parts table, quote the Agilent part number, indicate the quantity required, and address the
order to the nearest Agilent Technologies oce.
Table 4-7. 16007A Replaceable Parts
Agilent Part
Number
Qty.
Description
16007-600011
1
1
Alligator Clip Lead Red
Agilent internal-only part number.
16007B Replaceable Parts
Table 4-8 lists the replaceable parts for the 16007B. To order a part listed in the replaceable
parts table, quote the Agilent part number, indicate the quantity required, and address the
order to the nearest Agilent Technologies oce.
Table 4-8. 16007B Replaceable Parts
Agilent Part
Number
Qty.
Description
16007-600021
1
1
Alligator Clip Lead Black
Agilent internal-only part number.
Service
4-5
REGIONAL SALES AND SUPPORT OFFICES
For more information about Agilent Technologies test and measurement products, applications, services, and
for a current sales office listing, visit our web site: http://www.agilent.com/find/tmdir. You can also contact one
of the following centers and ask for a test and measurement sales representative.
11/29/99
United States:
Agilent Technologies
Test and Measurement Call Center
P.O.Box 4026
Englewood, CO 80155-4026
(tel) 1 800 452 4844
Canada:
Agilent Technologies Canada Inc.
5150 Spectrum Way
Mississauga, Ontario
L4W 5G1
(tel) 1 877 894 4414
Europe:
Agilent Technologies
Test & Measurement
European Marketing Organization
P.O.Box 999
1180 AZ Amstelveen
The Netherlands
(tel) (31 20) 547 9999
Japan:
Agilent Technologies Japan Ltd.
Call Center
9-1, Takakura-Cho, Hachioji-Shi,
Tokyo 192-8510, Japan
(tel) (81) 426 56 7832
(fax) (81) 426 56 7840
Latin America:
Agilent Technologies
Latin American Region Headquarters
5200 Blue Lagoon Drive, Suite #950
Miami, Florida 33126
U.S.A.
(tel) (305) 267 4245
(fax) (305) 267 4286
Australia/New Zealand:
Agilent Technologies Australia Pty Ltd
347 Burwood Highway
Forest Hill, Victoria 3131
(tel) 1-800 629 485 (Australia)
(fax) (61 3) 9272 0749
(tel) 0 800 738 378 (New Zealand)
(fax) (64 4) 802 6881
Asia Pacific:
Agilent Technologies
24/F, Cityplaza One, 1111 King’s Road,
Taikoo Shing, Hong Kong
(tel) (852)-3197-7777
(fax) (852)-2506-9284
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement