PLASMA TV SERVICE MANUAL
Internal Use Only
North/Latin America
Europe/Africa
Asia/Oceania
http://aic.lgservice.com
http://eic.lgservice.com
http://biz.lgservice.com
PLASMA TV
SERVICE MANUAL
CHASSIS : PU92C
MODEL : 50PS60
50PS60-UA
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by
in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace it
with the same specified type.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each esposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
AC Volt-meter
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on positioin, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
0.15uF
1.5 Kohm/10W
CANADA: LG Electronics Canada, Inc. 550 Matheson
Boulevard East Mississauga, Ontario L4Z 4G3
USA
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-2-
: LG Customer Interactive Center
P.O.Box 240007, 201 James Record Road Huntsville,
AL 35824
Digital TV Hotline 1-800-243-0000
LGE Internal Use Only
TABLE OF CONTENTS
SPECIFICATIONS.................................................................4
ADJUSTMENT INSTRUCTIONS ..........................................6
TROUBLE SHOOTING GUIDE ...........................................15
BLOCK DIAGRAM...............................................................47
EXPLODED VIEW...............................................................49
SCHEMATIC DIAGRAM..........................................................
PRINTED CIRCUIT BOARDS .................................................
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-3-
LGE Internal Use Only
SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.
V
Application Range
This spec is applied to the PLASMA TV used PU92A/PU92C Chassis.
Model Name
Chassis
Market
Brand
Remark
32PQ1DV-UA
42PQ20-UA
50PQ20-UA
42PQ30-UA
50PQ30-UA
42PQ60-UA
50PQ60-UA
PU92A
50PS30-UB
50PS60-UA
60PS60-UA
PU92C
V
LG
NORTH AMERICA
Specification
Each part is tested as below without special appointment.
1) Temperature : 25±5°C
2) Relative Humidity: 65±10%
3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.
4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with SBOM.
5) The receiver must be operated for about 20 minutes prior to the adjustment.
V
Test Method
1) Performance : LGE TV test method followed.
2) Demanded other specification
Safety : UL, CSA, IEC specification
EMC : FCC, ICES, IEC specification
Model
Market
Appliance
Remark
32PQ1DV-UA
42PQ20-UA
50PQ20-UA
42PQ30-UA
50PQ30-UA
42PQ60-UA
50PQ60-UA
Safety : UL1492, CSA C22.2.No. 1
NORTH AMERICA
EMC : FCC Class B, IC Class B
50PS30-UB
50PS60-UA
60PS60-UA
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-4-
LGE Internal Use Only
SPECIFICATIONS
V
General Specification
No.
Item
1
Receiving System
ATSC/64 & 256 QAM/NTSC-M
2
Available Channel
1) VHF : 02 ~ 13
Specification
2) UHF : 14 ~ 69
3) DTV : 02 ~ 69
4) CATV : 01 ~ 135
5) CADTV : 01 ~ 135
3
Input Voltage
1) AC 100 ~ 240V 50/60Hz
2) AC 100 ~ 120V 50/60Hz
4
Market
5
Screen Size
NORTH AMERICA
42 inch Wide(1024 X 768)
50 inch Wide(1365 X 768)
60 inch Wide(1365 X 768)
50 inch Wide(1920 X 1080)
60 inch Wide(1920 X 1080)
6
Aspect Ratio
7
Tuning System
8
Module
16 : 9
FS
PDP32F2####(852 X 480)
PDP42G2####(1024 X 768)
PDP50G2####(1365 X 768)
PDP50H3####(1920 X 1080)
PDP60H3####(1920 X 1080)
9
Operating Environment
1) Temp : 0 ~ 40deg
2) Humidity : ~80%
10
Storage Environment
1) Temp : -20 ~ 60deg
2) Humidity : 0 ~ 90%
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-5-
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
1. Application Range
Caution: Set up “RF mode(noise)” after PCB assembly adjustment.
This spec sheet is applied to all of the “PU92A(HD)” and
“PU92C(FHD)” Chassis.
3. Download
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25±5cC of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15cC
- In case of keeping module is in the circumstance of 0cC,
it should be placed in the circumstance of above 15cC for
2 hours
- In case of keeping module is in the circumstance of below
-20cC, it should be placed in the circumstance of above
15cC for 3 hours.
1) Press the POWER ON KEY on R/C for adjustment.
2) Press the ADJ KEY on R/C and enter EZ ADJUST.
Select “4. WHITE PATTERN” by using D/E(CH +/-) and
select “White” by using F/G(VOL +/-)
(1) Execute ISP program “Mstar ISP Utility” and then click
“Config” tab.
(2) Set as below, and then click “Auto Detect” and check “OK”
message If display “Error”, Check connect computer, jig,
and set.
(3) Click “Connect” tab. If display “Can’t” , Check connect
computer, jig, and set.
(4) Click “Read” tab, and then load download file(XXXX.bin)
by clicking “Read”
- Set is activated HEAT run without signal generator in this
mode.
- Single color pattern (RED / BLUE / GREEN) of HEAT RUN
MODE uses to check panel.
Caution: If you turn on a still screen more than 20 minutes
(Especially digital pattern, cross hatch pattern), an after
image may be occur in the black level part of the
screen.
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-6-
(5) Click “Auto” tab and set as below
(6) Click “Run”.
(7) After downloading, check “OK” message.
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
4) Signal equipment displays
Impress Resolution 1080i
Model, Pattern : Internal pattern of Mstar scaler
4. ADC Process
4-1. PC Input ADC
5) Adjust by commanding AUTO_COLOR_ADJUST(0xF1)
0x00 0x02 instruction
(1) Auto RGB Gain/Offset Adjustment
1) Convert to PC in Input-source
I2C COMMAND: 0xF4 (SELECT_INPUT) 0x00 0x60
(RGB)
cf. 0x10(TV), 0x20(AV), 0x40(COMPONENT), 0x60
(RGB), 0x90(HDMI)
[ Manual ADC process using Service Remocon. After enter
Service Mode by pushing “ADJ” key, execute “ADC Adjust” by
pushing “G” key at “0. ADC CALIBRATION”.
2) Signal equipment displays
Output Voltage : 700 mVp-p
Impress Resolution XGA (1024 x 768 @ 60Hz)
Model, Pattern : Internal pattern of Mstar scaler
3) Adjust by commanding AUTO_COLOR_ADJUST(0xF1)
0x00 0x02 instruction.
(2) Confirmation
1) We confirm whether “0xB6(RGB)” address of EEPROM
“0xA2” is “0xAA” or not.
2) If “0xB6(RGB)” address of EEPROM “0xB2” isn’t “0xAA”,
we adjust once more
3) We can confirm the ADC values from “0xB0~0xB5
(RGB)” addresses in a page “0xA2”
4-3. Confirmation
(1) We confirm whether “0xBF(480i)/0xC8(1080i)” address of
EEPROM “0xA2” is “0xAA” or not.
(2) If “0xBF(480i)/0xC8(1080i)” address of EEPROM “0xA2”
isn’t “0xAA”, we adjust once more
(3) We can confirm the ADC values from “0xB9 ~ 0xBE(480i) /
0xC2 ~ (1080i)” addresses in a page “0xA2”
[ Manual ADC process using Service Remocon. After enter
Service Mode by pushing “ADJ” key, execute “ADC Adjust” by
pushing “G” key at “0. ADC CALIBRATION “.
[ Manual ADC Confirmation using Service Remocon. After enter
Service Mode by pushing “INSTART” key.
4-2. COMPONENT Input ADC
5. DDC EDID Write Confirmation
(1) Component Gain/Offset Adjustment
1) Convert to Component in Input-source
I2C COMMAND : 0xF4 (SELECT_INPUT) 0x00 0x40
(COMPONENT)
cf. 0x10(TV), 0x20(AV), 0x40(COMPONENT), 0x60
(RGB), 0x90(HDMI)
2) Signal equipment displays
Impress Resolution 480i
Model, Pattern : Internal pattern of Mstar scaler
3) Adjust by commanding AUTO_COLOR_ADJUST(0xF1)
0x00 0x02 instruction
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-7-
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
Caution: Each PCB assembly must be checked by check JIG set.
(Because power PCB Assembly damages to PDP
Module, especially be careful)
2) After turning VR951, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top
(deviation ; ±0.5V)
Caution: Set up “RF mode(noise)” before voltage adjustment.
6. POWER PCB Ass’y Voltage
Adjustment (Va, Vs voltage Adjustment)
6-1. Test Equipment: D.M.M 1EA
6-2. Connection Diagram for Measuring
Refer to Fig.1, Fig 2, Fig 3
6-3. Adjustment Method
(Fig. 2) 42inch Power PCB Assy Voltage Adjustment
(1) 50” Va Adjustment (refer fig.1)
1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M. to Va pin of P802,
connect-terminal to GND pin of P802.
3) After turning VR902,voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top
(deviation; ±0.5V)
(2) 50” Vs Adjustment (refer fig.1)
1) Connect + terminal of D.M.M. to Vs pin of P802, connect
-terminal to GND pin of P802.
2) After turning VR901, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top
(deviation ; ±0.5V)
(5) 60” Va Adjustment (refer fig.3)
1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M. to Va pin of P11, connect
-terminal to GND pin of P11.
3) After turning VR901,voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top
(deviation; ±0.5V)
(6) 60” Vs Adjustment (refer fig.3)
1) Connect + terminal of D. M..M. to Vs pin of P11, connect
-terminal to GND pin of P11.
2) After turning VR951, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top
(deviation ; ±0.5V)
(Fig. 1) 50inch Power PCB Assy Voltage Adjustment
(Fig. 3) 60inch Power PCB Assy Voltage Adjustment
(3) 42” Va Adjustment (refer fig.2)
1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M. to Va pin of P811, connect
-terminal to GND pin of P811.
3) After turning VR901,voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top
(deviation; ±0.5V)
(4) 42” Vs Adjustment (refer fig.2)
1) Connect + terminal of D. M..M. to Vs pin of P811,
connect -terminal to GND pin of P811.
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-8-
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
7. DDC EDID Write
(MODEL NAME: LG TV(Not necessary))
Caution: Please only check write status in Instart-menu
- EDID download is processed automatically through CPU at initial booting
- PC(for communication through RS-232C), UART baud rate: 115200 bps
7-1. HD EDID DATA
(1) RGB EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x18, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30, 0x40, 0x70,
/* 4 */ 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
/* 5 */ 0x58, 0x2C, 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xFF,
/* 8 */ 0x02, 0x03, 0x04, 0x00, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00,
/* 9 */ 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1C, 0xF1, 0x27, 0x00, 0xA0, 0x51, 0x00, 0x25, 0x30, 0x50, 0x80,
/* a */ 0x37, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* b */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* c */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* d */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* e */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* f */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x31,
(2) HDMI-1 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30, 0x40, 0x70,
/* 4 */ 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
/* 5 */ 0x58, 0x2C, 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xBD,
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-9-
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
(3) HDMI-2 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30, 0x40, 0x70,
/* 4 */ 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
/* 5 */ 0x58, 0x2C, 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x20, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xAD,
(4) HDMI-3 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30, 0x40, 0x70,
/* 4 */ 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
/* 5 */ 0x58, 0x2C, 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x30, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x9D,
(5) HDMI-4 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30, 0x40, 0x70,
/* 4 */ 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40,
/* 5 */ 0x58, 0x2C, 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x40, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x8D,
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 10 -
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
7-2. Full-HD EDID DATA
(1) RGB EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x18, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C,
/* 4 */ 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30,
/* 5 */ 0x40, 0x70, 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xFF,
/* 8 */ 0x02, 0x03, 0x04, 0x00, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00,
/* 9 */ 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1C, 0xF1, 0x27, 0x00, 0xA0, 0x51, 0x00, 0x25, 0x30, 0x50, 0x80,
/* a */ 0x37, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* b */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* c */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* d */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* e */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* f */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x31,
(2) HDMI-1 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C,
/* 4 */ 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30,
/* 5 */ 0x40, 0x70, 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xBD,
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 11 -
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
(3) HDMI-2 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C,
/* 4 */ 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30,
/* 5 */ 0x40, 0x70, 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x20, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xAD,
(4) HDMI-3 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C,
/* 4 */ 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30,
/* 5 */ 0x40, 0x70, 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x30, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x9D,
(5) HDMI-4 EDID DATA
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
————————————————————————————————————————————
/* 0 */ 0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x1E, 0x6D, 0x01, 0x00, 0x01, 0x01, 0x01, 0x01,
/* 1 */ 0x00, 0x11, 0x01, 0x03, 0x80, 0x73, 0x41, 0x96, 0x0A, 0xCF, 0x74, 0xA3, 0x57, 0x4C, 0xB0, 0x23,
/* 2 */ 0x09, 0x48, 0x4C, 0xAF, 0xCF, 0x00, 0x31, 0x40, 0x45, 0x40, 0x61, 0x40, 0x81, 0x80, 0xA9, 0x40,
/* 3 */ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C,
/* 4 */ 0x45, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x66, 0x21, 0x50, 0xB0, 0x51, 0x00, 0x1B, 0x30,
/* 5 */ 0x40, 0x70, 0x36, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x00, 0x00, 0x00, 0xFD, 0x00, 0x30,
/* 6 */ 0x4B, 0x1F, 0x64, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFC,
/* 7 */ 0x00, 0x4C, 0x47, 0x20, 0x54, 0x56, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x97,
/* 8 */ 0x02, 0x03, 0x1B, 0xF1, 0x47, 0x84, 0x05, 0x03, 0x02, 0x20, 0x22, 0x10, 0x26, 0x15, 0x07, 0x50,
/* 9 */ 0x09, 0x07, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x40, 0x00, 0xB8, 0x2D, 0x01, 0x1D, 0x00, 0x72, 0x51,
/* a */ 0xD0, 0x1E, 0x20, 0x6E, 0x28, 0x55, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80,
/* b */ 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58, 0x2C, 0x25, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00, 0x9E, 0x8C,
/* c */ 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0xC4, 0x8E, 0x21, 0x00, 0x00,
/* d */ 0x18, 0x8C, 0x0A, 0xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x13, 0x8E, 0x21,
/* e */ 0x00, 0x00, 0x18, 0x0E, 0x1F, 0x00, 0x80, 0x51, 0x00, 0x1E, 0x30, 0x40, 0x80, 0x37, 0x00, 0xC4,
/* f */ 0x8E, 0x21, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x8D,
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 12 -
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
8. Adjustment of White Balance
Caution: Press the POWER ON KEY on R/C before W/B adjustment.
8-2. Connecting Picture of the Measuring
Instrument (On Automatic control )
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push control R/C ADJ Key—> Enter the
mode of White-Balance, the pattern will come out.
8-1. Test Equipment
- Color Analyzer (CS-1000, CA-100+(CH.10), CA-210(CH.10))
[ Please adjust CA-100+ / CA-210 by CS-1000 before measuring
--> You should use Channel 10 which is Matrix compensated
(White, Red, Green, Blue revised) by CS-1000 and adjust
in accordance with White balance adjustment coordinate.
O
Color temperature standards according to CSM and Module
8-3. Auto-control Interface and Directions
O
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (illumination is less than 10ux).
(2) In case of PDP: Measure and adjust after sticking the Color
Analyzer (CA-100+, CA210) to the side of the module.
Change target luminance and range of the Auto adjustment
W/B equipment.
In case of LCD: Adhere closely the Color Analyzer (
CA210) to the module less than 10cm distance, keep it
with the surface of the Module and Color Analyzer’s Prove
vertically.(80~100°).
(3) Aging time
1) After aging start, keep the power on (no suspension of
power supply) and heat-run over 15 minutes.
2) In case of PDP, keep white pattern using inside pattern.
3) In case of LCD, using ’no signal’ or ‘full white pattern’ or
the others, check the back light on.
O
White balance adjustment coordinate and color temperature
O
Cool
CS-1000
CA-100+ (CH.10)
x
0.276
0.276–0.002
0.276–0.002
y
0.283
0.283–0.002
0.283–0.002
3uv
0.000
0.000
0.000
Medium
CS-1000
CA-100+ (CH.10)
CA-210 (CH.10)
x
0.285
0.285–0.002
0.285–0.002
y
0.293
0.293–0.002
0.293–0.002
3uv
0.000
0.000
0.000
Warm
CS-1000
CA-100+ (CH.10)
CA-210 (CH.10)
x
0.313
0.313–0.002
0.313–0.002
y
0.329
0.329–0.002
0.329–0.002
3uv
0.003
0.003
CA-210 (CH.10)
Auto Adjustment Map(RS-232C)
0.003
[ PC (for communication through RS-232C) ==> UART Baud rate : 115200 bps
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 13 -
LGE Internal Use Only
ADJUSTMENT INSTRUCTIONS
8-4. Manual White Balance
(1) Press the POWER ON KEY on R/C for adjustment and
heat run over 5 minutes.
(2) Zero Calibrate CA-100+ / CA-210, and when controlling,
stick the sensor to the center of PDP module surface.
(3) Press the ADJ KEY on R/C and enter EZ ASJUST
Select “3.W/B ADJUST” and press ENTER(V)
Set test-pattern on and display inside pattern.
(4) Control is carried out on three color temperatures, COOL,
MEDIUM, WARM.(Control is carried out three times)
<Temperature: COOL>
- R-offset / G-offset / B-offset is set to 128
- Control R-Gain and G-Gain.
- Each gain is limited to 192
<Temperature: MEDIUM>
- R-offset / G-offset / B-offset is set to 128
- Control R-Gain and G-Gain.
- Each gain is limited to 192
<Temperature: WARM>
- R-offset / G-offset / B-offset is set to 128
- Control G-Gain and B-Gain.
- Each gain is limited to 192
9. HDCP SETTING(Not necessary)
Caution: Key is saved in external eeprom.
10. RS-232C
Press In-start key and select 4.Baud Rate menu. Check RS232C after changing Baud Rate 115200.
11. OPTION
(1) Press ADJ R/C In-start key and select 0.TOOL OPTION,
1.AREA OPTION
(2) Select Model name and Country by using F/G(VOL +/-) in
accordance with destination
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 14 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 15 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 16 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 17 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 18 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 19 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 20 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 21 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 22 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 23 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 24 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 25 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 26 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 27 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 28 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 29 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 30 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 31 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 32 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 33 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 34 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 35 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 36 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 37 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 38 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 39 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 40 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 41 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 42 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 43 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 44 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 45 -
LGE Internal Use Only
TROUBLE SHOOTING GUIDE
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 46 -
LGE Internal Use Only
BLOCK DIAGRAM
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 47 -
LGE Internal Use Only
BLOCK DIAGRAM
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 48 -
LGE Internal Use Only
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
A10
250
501
901
LV1
A2
202
560
330
310
570
302
203
207
120
540
305
204
205
201
580
300
304
301
303
590
240
200
206
208
900
603
602
520
601
400
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by
in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
- 49 -
LGE Internal Use Only
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
MAIN(TOP)
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
MAIN(BOTTOM)
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
LED(TOP)
CONTROL(TOP)
LED(BOTTOM)
CONTROL(BOTTOM)
Copyright©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
Feb., 2009
Printed in Korea
P/NO : MFL60621702
CANADA: LG Electronics Canada, Inc. 550 Matheson
Boulevard East Mississauga, Ontario L4Z 4G3
USA
: LG Electronics Alabama, Inc.
P.O.Box 240007, 201 James Record Road Bldg 3
Huntsville, AL 35824
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement