null  null
67XXU
USB/Serial Scale Series
Service Manual
SOFTWARE VERSION 1.20
AWT35-501145
Issue AD
Brecknell is part of Avery Weigh-Tronix. Avery Weigh-Tronix is a trademark of the Illinois Tool Works group of companies whose
ultimate parent company is Illinois Tool Works Inc (“Illinois Tool Works”). Copyright © 2014 Illinois Tool Works. All rights reserved.
No part of this publication may be reproduced by making a facsimile copy, by the making of a copy in three dimensions of a two-dimensional
work and the making of a copy in two dimensions of a three-dimensional work, stored in any medium by electronic means, or transmitted in
any form or by any means, including electronic, mechanical, broadcasting, recording or otherwise without the prior written consent of the
copyright owner, under license, or as permitted by law.
This publication was correct at the time of going to print, however Avery Weigh-Tronix reserves the right to alter without notice the
specification, design, price or conditions of supply of any product or service at any time.
67xx Serial Scale_s_en_500145.book
Table of Contents
Chapter 1 General Information and Warnings ........................................................................................ 3
About this Manual .............................................................................................................. 3
Text Conventions ........................................................................................................ 3
Special Messages ....................................................................................................... 3
Warnings ............................................................................................................................ 4
Routine Maintenance ......................................................................................................... 4
Sharp Objects .................................................................................................................... 4
Cleaning the Indicator ........................................................................................................ 4
CE Certification .................................................................................................................. 5
Chapter 2 Installation ................................................................................................................................ 6
Connections ....................................................................................................................... 7
Display ......................................................................................................................... 7
Power Supply .............................................................................................................. 7
USB Port (Com 1) ....................................................................................................... 7
RS-232 Serial Port (Com 2) ........................................................................................ 7
Remote Display and Mounting ........................................................................................... 8
Mainboard .......................................................................................................................... 9
Definition of Connectors and Jumpers ........................................................................ 9
Chapter 3 Specifications ......................................................................................................................... 11
Available Models .............................................................................................................. 11
Outline Dimensions .......................................................................................................... 11
Mounting .......................................................................................................................... 12
Power Supply ................................................................................................................... 12
Display ............................................................................................................................. 12
Keypad ...................................................................................................................... 12
Environment ............................................................................................................. 12
Load Cell Excitation ................................................................................................... 12
Approvals ......................................................................................................................... 12
Communication ................................................................................................................ 13
Analog Circuitry ................................................................................................................ 13
Capacity and Division ...................................................................................................... 13
Accuracy .......................................................................................................................... 13
Calibration Method ........................................................................................................... 13
Other Main Functions ....................................................................................................... 14
Chapter 4 Configuration .......................................................................................................................... 15
Front Panel ...................................................................................................................... 15
Keys ................................................................................................................................. 16
Navigating the Weigh Mode ............................................................................................. 17
Enter the Weigh Mode ............................................................................................... 17
Enter or Exit the HOLD Mode .................................................................................... 17
Zero ........................................................................................................................... 17
Tare ........................................................................................................................... 17
Preset Tare Weight ................................................................................................... 17
Clear Tare Weight ..................................................................................................... 17
Output Data (print to a computer or printer) .............................................................. 18
Display Gross or Net Weight ..................................................................................... 18
Change Weight Unit .................................................................................................. 18
Check Weight (compare feature) .............................................................................. 20
Navigating the Count Mode ............................................................................................. 20
Enter Count Mode ..................................................................................................... 20
Obtain Piece Weight .................................................................................................. 21
Hold Function ................................................................................................................... 22
67XXU USB/Serial Scale Service Manual
1
Activate the Hold Function ........................................................................................ 22
Access the Hold Mode .............................................................................................. 22
Hold Methods ............................................................................................................ 22
Display Software and Hardware Version ......................................................................... 24
Display Test ..................................................................................................................... 24
Keyboard and Buzzer Test .............................................................................................. 24
Serial Port 1/2 (COM1/2) Receiving Test ......................................................................... 25
Serial Port 1/2 (COM1/2) Transmitting Test ..................................................................... 25
Chapter 5 Setup Mode ............................................................................................................................. 26
Entering the Setup Menu ................................................................................................. 26
Navigating the Setup Menu .............................................................................................. 26
Setup Menu Parameters .................................................................................................. 27
CONFG Menu ........................................................................................................... 27
USER Menu .............................................................................................................. 32
CAL Menu ................................................................................................................. 42
MISC Menu ............................................................................................................... 44
TEST Menu ............................................................................................................... 44
Exit the Setup Menu ......................................................................................................... 45
Chapter 6 Calibration .............................................................................................................................. 46
Enter the Calibration Mode .............................................................................................. 46
Zero Point .................................................................................................................. 46
Linearity ..................................................................................................................... 47
Geographical Adjustment ................................................................................................. 48
Gravity Value ................................................................................................................... 50
Input or View Calibration .................................................................................................. 50
Weight Fine-tune .............................................................................................................. 51
Display ADC Output Code ............................................................................................... 51
Chapter 7 Serial Communication ........................................................................................................... 52
Communication Settings .................................................................................................. 52
Com Port 1 ....................................................................................................................... 53
Com Port 2 ....................................................................................................................... 53
Protocol ............................................................................................................................ 53
Transaction String ............................................................................................................ 53
Commands and Response .............................................................................................. 54
Parameter NCI-SCP01 .............................................................................................. 54
Parameter ECR-SCP02 ............................................................................................ 57
Parameter 8213-SCP03 ............................................................................................ 60
Parameter Multi ......................................................................................................... 63
Parameter EH-SCP (PS-60) ...................................................................................... 65
Parameter IBM .......................................................................................................... 66
Chapter 8 Legal for Trade ....................................................................................................................... 69
Physical Seal ................................................................................................................... 69
Audit Trail Parameters ..................................................................................................... 70
View Configuration Counter ...................................................................................... 70
View Calibration Counter ........................................................................................... 70
Chapter 9 Troubleshooting ..................................................................................................................... 71
Display Characters ........................................................................................................... 71
Display Symbols .............................................................................................................. 72
Error Messages and Troubleshooting .............................................................................. 73
2
67XXU USB/Serial Scale Service Manual
1
General Information and Warnings
1.1
About this Manual
This manual is divided into chapters by the chapter number and the large text at the top
of a page. Subsections are labeled as shown by the 1 and 1.1 headings shown above.
-The names of the chapter and the next subsection level appear at the top of alternating
pages of the manual to remind you of where you are in the manual. The manual name
and page numbers appear at the bottom of the pages.
1.1.1 Text Conventions
The keys used to interface with the 67XXU are located on the front panel of the
indicator. The keystrokes are shown in BOLD incased between brackets. (e.g. [ZERO])
Displayed messages appear in seven segment display type and reflect the case of the
displayed message. (e.g. confg)
1.1.2 Special Messages
Examples of special messages you will see in this manual are defined below. The
signal words have specific meanings to alert you to additional information or the relative
level of hazard.
CAUTION!
This is a Caution symbol.
Cautions give information about procedures that, if not observed, could result
in damage to equipment or corruption to and loss of data.
ELECTRICAL WARNING!
THIS IS AN ELECTRICAL WARNING SYMBOL.
ELECTRICAL WARNINGS MEAN THAT FAILURE TO FOLLOW
SPECIFIC PRACTICES OR PROCEDURES MAY RESULT IN
ELECTROCUTION, ARC BURNS, EXPLOSIONS OR OTHER HAZARDS
THAT MAY CAUSE INJURY OR DEATH.
NOTE: This is a Note symbol. Notes give additional and important information, hints
and tips that help you to use your product.
67XXU USB/Serial Scale Service Manual
3
1.2
1.3
Warnings
l
Avoid lengthy exposure to extreme heat or cold. Your scale works best when
operated at normal room temperature. Always allow the scale to acclimate to
a normal room temperature before use.
l
Allow sufficient warm up time. Turn the scale on and wait for a few minutes if
possible. This will give the internal components a chance to stabilize before
weighing.
l
These electronic scales are precision instruments. Do not operate near an
in-use cell phone, radio, computer or other electronic device. These devices
emit RF and can cause unstable scale readings. If your scale ever performs
poorly, try moving the scale to a different room or location.
l
Avoid using in heavy vibration and airflow conditions.
l
Read the weight reading in short time after loading. The output signature of
load cell and electronic circuit may be little influenced after weighing for a
long time.
Routine Maintenance
IMPORTANT: This equipment must be routinely checked for proper operation
and calibration.
Application and usage will determine the frequency of calibration required for
safe operation.
Always turn off the machine and isolate from the power supply before starting any
routine maintenance to avoid the possibility of electric shock.
1.4
Sharp Objects
Do not use sharp objects such as screwdrivers or long fingernails to operate the keys.
1.5
Cleaning the Indicator
Table 1.1 Cleaning DOs and DON’Ts
DO
DO NOT
Wipe down the outside of standard products Attempt to clean the inside of the indicator
with a clean cloth, moistened with water and Use harsh abrasives, solvents, scouring cleaners or
a small amount of mild detergent
alkaline cleaning solutions
Spray the cloth when using a proprietary
cleaning fluid
4
Spray any liquid directly on to the display window
67XXU USB/Serial Scale Service Manual
1.6
CE Certification
Pending
67XXU USB/Serial Scale Service Manual
5
2
Installation
DANGER: RISK OF ELECTRICAL SHOCK. BE SURE TO UPLUG THE
INDICATOR BEFORE REMOVING THE COVER OR OPENING THE UNIT.
REFER TO QUALIFIED SERVICE PERSONNEL FOR SERVICE.
1.
Unpack the scale and all components from the shipping box.
2.
Remove the shipping screw from the under side of the scale base. Refer to
Figure 2.1.
Figure 2.1 Shipping Screw Location
6
3.
Connect all necessary cables to the proper connectors. Refer to this section
for connection details.
4.
Level the scale base using the four leveling feet. View the level bubble located
under the platform top.
67XXU USB/Serial Scale Service Manual
2.1
Connections
There are connectors located on the side of the scale for the power supply, USB port,
RS-232 serial port and display which is used for mounting the display remotely on a
wall or a desk.
Figure 2.2 View of Scale Connectors
2.1.1 Display
The indicator display can be removed from the scale and mounted on a wall or desk.
Refer to section 2.2 for details on mounting.
2.1.2 Power Supply
The 67XXU comes with an external AC to DC power adapter. Simply plug the AC
adapter into the DC6V power jack on the scale and then plug into a standard wall outlet.
IMPORTANT: Make sure that the AC voltage and polarity appearing at the wall
outlet matches the input voltage as well as the polarity marked on the AC
adapter.
2.1.3 USB Port (Com 1)
The USB connector is used as a virtual RS-232 port and USB power supply.
2.1.4 RS-232 Serial Port (Com 2)
The 67XXU comes standard with one full Bi-directional RS-232 serial port designed for
connection to either a PC or a serial printer.
l
Pin 2 = transmit
l
Pin 3 = receive
67XXU USB/Serial Scale Service Manual
7
The RS-232 port connector is a 9-pin female..
Figure 2.3 RS-232 Connector (Com 2)
2.2
Remote Display and Mounting
The indicator is connected to the front of the 67XXU. It can be removed however to
accommodate mounting on a wall or desk. Plug the display cable into the DISPLAY
connector.
Figure 2.4 Indicator Desk Mount
Figure 2.5 Indicator Wall Mount
8
67XXU USB/Serial Scale Service Manual
2.3
Mainboard
Figure 2.6 shows the main board connectors for the loadcell, RS-232 port, USB port,
power supply and battery.
Figure 2.6 67XXU Main Circuit Board
2.3.1 Definition of Connectors and Jumpers
Table 2.1 Loadcell Connector
Pin
Description
In/Out/Power
Electrical Level
1
+ excitation
power output
5±0.3 VDC (≤0.12A)
2
+ sense
power input
5±0.3 VDC
3
- excitation
power ground
0 VDC
4
- sense
power input
≤0.5 VDC
5
+ signal
signal input
2.5±0.3 VDC
6
- signal
signal input
2.5±0.3 VDC
7
shield
-
-
Table 2.2 Adapter Power Input Connector (ADP)
Pin #
Definition
In/Out/Power
Electrical Level
1
Adapter input voltage - (GND)
Power ground
0VDC
2
Adapter input voltage +
Power input
6.5 VDC (6-9VDC, ≥0.5A)
67XXU USB/Serial Scale Service Manual
9
Table 2.3 USB Connector (USB) Com 1
Pin
Description
In/Out/Power
Electrical Level
1
GND of VDD
power ground
0 VDC
2
USB D+
0-5 VDC
3
USB D-
0-5 VDC
4
USB power
power input
5±0.25 VDC
Table 2.4 RS-232 Port Connector (SIO) Com 2
Pin
Description
In/Out/Power
Electrical Level
2
RS-232 transmit on UART0
Output
-12 to +12 VDC
3
RS-232 receive on UART0
Input
-12 to +12 VDC
5
GND
Power ground
0 VDC
Table 2.5 CAL Jumper Set
Connected Pins
10
Function
Push
calibration enabled
No push
calibration disabled
67XXU USB/Serial Scale Service Manual
3
Specifications
3.1
Available Models
3.2
6702U
6”x10” (15 or 30 lb)
6710U
10”x10” (15 or 30 lb)
6720U
12”x14” (15 or 30 lb)
Outline Dimensions
Figure 3.1 67XXU Dimension Drawing
Figure 3.2 67XXU Dimension Drawing with Indicator on a Column
67XXU USB/Serial Scale Service Manual
11
3.3
3.4
3.5
Mounting
l
Bracket
l
Remote (optional cable required)
l
Column (option kit required)
Power Supply
l
AC Adapter: 7-9VDC, ≥500mA, center positive
l
USB power supply if USB interface is installed
l
Work current: ≤15mA (with backlight off, and no load cells)
m
≤30mA (with backlight on, and no load cells)
m
≤50mA (with backlight on and one 350 load cell)
Display
l
51/2-digit,7-segment , 0.58" (15mm) LCDs
l
4 push buttons
3.5.1 Keypad
3.5.2 Environment
Working temperature
-10°C to 40°C
Storage temperature
-20°C to 70°C
Humidity
10 to 90% RH without condensation
3.5.3 Load Cell Excitation
3.6
12
Voltage
5VDC
Max. Current
20mA
Approvals
NTEP
13-074
Measurement Canada
AM-5912C
67XXU USB/Serial Scale Service Manual
3.7
3.8
3.9
Communication
Serial port1
Full-duplex RS-232
Optional Serial Port
USB (Virtual RS-232)
Baud Rate
Selectable: 1200-2400-4800-9600-19200-38400 bps
Data Output Format
8N1, 7O1, 7E1
Protocol
programmable
Analog Circuitry
l
24-bit A/D converter
l
Conversion Speed: 10Hz
l
Input range: -15mV to +15mV
l
Output code:1mV input will output about 100,000 raw counts
l
Hardware low pass filter and 2 programmable digital low pass filters
Capacity and Division
l
Programmable
l
Max display range: -199,999 to 199,999
l
Division number range for primary unit: 100-20,000
m
l
Division number range for second unit: 100-25,000 (division number will
be limited by REGUL setting)
Recommended Sensitivity: >1µV/ display division
3.10 Accuracy
≤0.01%
3.11 Calibration Method
l
Software calibration with long-term storage in EEPROM
l
Provides smooth curve fit through four points
l
Calibration can be done under kg or lb weight unit with 10% -100%FS
standard weight.
l
Weight fine adjustment (± 10%)
l
Geographic adjustment
67XXU USB/Serial Scale Service Manual
13
3.12 Other Main Functions
14
l
Programmable zero range
l
Programmable pre-set tare weight
l
Programmable automatic zero point tracking
l
Programmable motion detection window
l
Programmable auto-power off time, backlight working mode
l
Programmable hold function with peak weight holding and dynamic weighing
l
Available check weighing mode
l
Available parts counting mode
l
Available units of measure: kg, lb, lb:oz, oz, g, PCS
l
Data comparison and indicator in weighing mode and parts counting mode
l
Programmable serial output content
67XXU USB/Serial Scale Service Manual
4
Configuration
To set up the indicator, you must first enter the appropriate menu mode. The front panel
keys become directional navigators to move around in the menus. See Table 4.2 for
details.
4.1
Front Panel
The front panel incorporates the display and keypad.
The annunciators used are incorporated in the display. The annunciator will be lit went
the mode is active.
Figure 4.1 67XXU Keypad and Display
Table 4.1 LCD Display Annunciators and Definitions
LCD Annunciator
Description
Better known as the "Center of Zero" annunciator. It is lit when the scale is at the zero point
and the gross weight is 0.
NET
Indicates net mode and the tare weight is not 0.
lb
Indicates the current unit of measure is lb.
oz
Indicates the current unit of measure is oz.
kg
Indicates the current unit of measure is kg.
g
Indicates the current unit of measure is g.
Pcs
HOLD
AC/CHG
OK
Indicates counting mode. Unit of measure is pieces.
Flashes when HOLD key is pressed. Remains permanently on when the Hold function has
become activated.
When battery is being used or charged, is fully charged or not installed.
Indicates when data compare is enabled and current data (weight, pieces or percent) is
between the specified upper and lower limits.
67XXU USB/Serial Scale Service Manual
15
4.2
Keys
The keyboard consists of four keys, some of which have multiple functions.
Table 4.2 Function of the Keys
Key
Mode
Condition
Function
Weigh or count
Press for less than 3 seconds
Enter or exit HOLD/PRINT mode
Weigh or count
Press [HOLD] + [ON/OFF] for more
than 3 seconds
Enter setup mode
Input data mode
Press for more than 3 seconds
Input decimal point
Input data mode
Press for less than 3 seconds
Rotate the flashed position from right to left
Menu selection mode
Select next item of current menu
Weigh or count
Press [HOLD] + [UNIT] for more than 3 Select working mode (weigh or count)
seconds
Weigh mode
Press for less than 3 seconds
Change weighing units: kg->lb->oz
lb:oz (not available in some conditions)
g (not available in some conditions)
kg (not be available in some conditions)
Count mode
Press for less than 3 seconds
To enter piece weight mode (by way of
sample or input directly)
Weigh or count
Press for more than 3 seconds
To input compare data (for weight or pieces)
of high and low limitation
Display voltage mode
Press for more than 3 seconds
To calibrate input voltage value
Display ADC code mode
Input data mode
Select displaying code from:
no-filter, filter1, filter2
Press to enter data
Menu selection mode
one will be added to the flashing digit
Select next item of current menu
Weigh or count
Press for less than 3 seconds
Tare function
Weigh or count
Press for more than 3 seconds
Input pre-set tare weight at selected weight
unit
Input data mode or
Menu selection mode
Press to enter data
To confirm input data or current item
selection. Select next item of current menu or
next operation
Display ADC code mode
Set or clear tare code
Power off mode
Power on
Count or weigh
Press for less than 3 seconds
Zero function
Count or weigh
Press for more than 3 seconds
Power off
Input data
Ignore current operation
Menu selection mode
Return to last sub-menu
NOTE: To access the second function of the key, press and hold the key for more
than 3 seconds.
16
67XXU USB/Serial Scale Service Manual
4.3
Navigating the Weigh Mode
4.3.1 Enter the Weigh Mode
Press the [HOLD] + [UNIT] keys for 3 seconds. Use the [UNIT] key to choose the
desired mode and the [TARE] key to confirm selection and exit to the chosen mode.
4.3.2 Enter or Exit the HOLD Mode
Press the [HOLD] key for 3 seconds.
4.3.3 Zero
When the weight is stable and within the zero range, press the [ZERO] key to set a new
zero point. Refer to Table 4.3 for zero limitations.
4.3.4 Tare
When the gross weight is larger than zero and the scale is stable, press the [TARE]
key. The indicator will show a net weight of zero and the NET annunciator will be
illuminated. Refer to Table 4.3 for tare limitations.
4.3.5 Preset Tare Weight
Enter a preset tare weight by pressing the [TARE] key for more than 3 seconds.
Pr.Tar will be displayed and the NET annunciator flashes. Use the [UNIT] and
[TARE] key to input the desired tare weight and the [HOLD] key to move to the next
digit. The value entered must be larger than zero and there is no limitation to preset
tare weight. After the tare weight is entered the NET annunciator will illuminate. Refer
to Table 4.3 for tare limitations.
Note: This indicator can only save one tare weight. The new tare weight will
automatically replace the old one.
4.3.6 Clear Tare Weight
Remove any weight on platform and wait until the scale is stable. Press the [TARE] key.
Table 4.3 Zero and Tare Limitations
key function
Standard
Weight on
platform
Data in TARE
memory unit
Tare key
Zero key
USA
≤0
no
No action
Zero
yes
Clear the tared weight
no
Tare
>0
yes
67XXU USB/Serial Scale Service Manual
17
key function
Standard
Weight on
platform
Data in TARE
memory unit
Tare key
Zero key
Canada
≤0
no
No action
Zero
yes
Clear the tared weight
no
Tare
yes
No action
no
No action
Zero
yes
Clear the tared weight
Zero and clear the
tared weight
no
Tare
Zero
>0
Europe
≤0
>0
yes
None
(same with Europe)
≤0
>0
Zero and clear the
tared weight
no
No action
Zero
yes
Clear the tared weight
Zero and clear the
tared weight
no
Tare
Zero
yes
Zero and clear the
tared weight
Zero can only be active when the scale is stable and weight is in SAZSM setting
range.
Tare can only be active when the scale is stable.
Clearing the Tare weight or Zeroing the scale will put the indicator into Gross mode.
Adding a Tare weight will put the indicator into Net mode.
4.3.7 Output Data (print to a computer or printer)
When scale is stable press the [PRINT] key.
4.3.8 Display Gross or Net Weight
l
If the tare weight is not zero, the Net weight will be displayed.
l
If the tare weight is zero, Gross weight will be displayed.
4.3.9 Change Weight Unit
Press the [UNIT] key to select kg, lb, oz, lb:oz, g. Note: under some conditions oz,
lb:oz, g are not available. Please refer the following tables.
18
67XXU USB/Serial Scale Service Manual
Table 4.4 Use kg as Primary Unit
Display Division Value
Calibration
Division Value
kg
g
lb
oz
lb:oz
0.0001kg
0.0001kg
0.1g
0.0002lb
0.005oz
Not available
0.001kg
0.001kg
1g
0.002lb
0.05oz
Not available
0.01kg
0.01kg
10g
0.02lb
0.5oz
0.5oz
0.1kg
0.1kg
Not available
0.2lb
5oz
Not available
1kg
1kg
Not available
2lb
Not available
Not available
0.0002kg
0.0002kg
0.2g
0.0005 lb
0.01oz
Not available
0.002kg
0.002kg
2g
0.005 lb
0.1oz
0.1 oz
0.02kg
0.02kg
20g
0.05 lb
1oz
1 oz
0.2kg
0.2kg
Not available
0.5 lb
10oz
Not available
2kg
2kg
Not available
5 lb
Not available
Not available
0.0005kg
0.0005kg
0.5g
0.001 lb
0.02oz
Not available
0.005kg
0.005kg
5g
0.01 lb
0.2oz
0.2 oz
0.05kg
0.05kg
50g
0.1 lb
2oz
2oz
0.5kg
0.5kg
Not available
1 lb
Not available
Not available
5kg
5kg
Not available
10 lb
Not available
Not available
Table 4.5 Use lb as Primary Unit
Display Division Value
Calibration
Division Value
kg
g
lb
oz
lb:oz
0.0001lb
Not available
Not available
0.0001lb
0.002oz
Not available
0.001 lb
0.0005 kg
0.5g
0.001 lb
0.02oz
Not available
0.01 lb
0.005 kg
5g
0.01 lb
0.2oz
0.2 oz
0.1 lb
0.05 kg
50g
0.1 lb
2oz
2 oz
1 lb
0.5 kg
Not available
1 lb
Not available
Not available
0.0002 lb
0.0001 kg
0.1g
0.0002 lb
0.005oz
Not available
0.002 lb
0.001 kg
1g
0.002 lb
0.005oz
Not available
0.02 lb
0.01 kg
10g
0.02 lb
0.5oz
0.5 oz
0.2 lb
0.1 kg
Not available
0.2 lb
5oz
Not available
2 lb
1 kg
Not available
2 lb
Not available
Not available
0.0005 lb
0.0002 kg
0.2g
0.0005 lb
0.01oz
Not available
0.005 lb
0.002 kg
2g
0.005 lb
0.1oz
0.1 oz
0.05 lb
0.02 kg
20g
0.05 lb
1oz
1 oz
0.5 lb
0.2 kg
Not available
0.5 lb
10oz
Not available
5 lb
2 kg
Not available
5 lb
Not available
Not available
67XXU USB/Serial Scale Service Manual
19
4.3.10 Check Weight (compare feature)
To make the weight compare function available, set CONFG-FUNC-COMPAR item to
YES (refer to Chapter 5 for details on entering and navigating the setup mode). The
high and low limitation of weight should be set correctly according to following steps:
1.
In weighing mode or count mode, press the [UNIT] key more than 3 seconds to
compare the high and low data.
1a.
If in the weigh mode and the COMP parameter is accessed, unt.lb or
unt.kg will be displayed when in the weigh mode. Use the [UNIT] key to
change the active unit.
1b.
If in the count mode, go to step 3.
2.
Use the [TARE] key access the high value. high and then L0000 will be
displayed.
3.
Use the [UNIT] and [HOLD] keys to enter the high value. Note: The [UNIT]
key changes the flashing digit. The [HOLD] key goes to the next digit.
4.
Press the [TARE] key to confirm the entry.
5.
After Low is accessed, L0000 will be displayed. Use the [HOLD] and [UNIT]
keys to input the low number.
6.
Press the [TARE] key to confirm.
6a.
After a reasonable limitation is set and compare is active, one of annunciators
OK will be illuminated. The beeper will sound according to its setting in USERBEEP.
7.
Press the [ZERO] key to exit the Comp mode.
NOTE: If the High number value is 0 or is equal or less than low number, the
comparison will be disabled, and the input data has no limitation.
4.4
Navigating the Count Mode
In this mode, the scale will weigh goods, calculate and display its counts after the piece
weight of the goods is obtained. The count function must be enabled in the setup mode.
The CONFG-FUNC-COUNT item should be set to YES in CONFIG menu. Refer to
Chapter 5 for details on entering and navigating the setup mode.
4.4.1 Enter Count Mode
20
1.
To enter counting mode press the [HOLD] + [UNIT] keys for more than 3
seconds. WEIGH will be displayed.
2.
Use the [UNIT] key to select COUNT.
3.
Press [TARE] to confirm the parts counting mode. The PCS annunciator will
be illuminated.
3a.
In counting mode, the function of [ZERO], [TARE], [PRINT], [ON/OFF] and
[HOLD] keys are available.
67XXU USB/Serial Scale Service Manual
4.4.2 Obtain Piece Weight
There are two ways to obtain the piece weight:
Input Piece Weight Directly
1.
Press the [UNIT] key.
2.
When InP.PW is displayed, press the [TARE] key to enter into the piece
weight mode.
3.
When UNIT.KG is shown, use the [UNIT] key to select the unit of piece
weight.
4.
Use the [TARE] key to confirm and go to piece weigh entry. The display will
show L0001 (Note: Since the LCD can only show 4 digits, but the software
allows 6 digits total, so there will be separate displays: L0001 and H00,
L0001 displays the low position digits and H00 displays the high position
digits).
5.
From the L0001 display, use [HOLD] and [UNIT] key to input new piece
weight.
5a.
Press the [UNIT] key to increase the numbers.
5b.
Press the [HOLD] key to change the flashed position.
5c.
Press the [HOLD] key more than 3 seconds to input decimal point.
5d.
If the input piece weight is less than 0.5d, the indicator will display PWt.Er
and go back to counting mode.
6.
Press the [TARE] key to confirm the entry.
7.
Press the [ZERO] key to exit the piece weight mode and back to counting
mode.
Sample a Known Quantity
1.
Press the [UNIT] key.
2.
When In.PWt is shown, use the [UNIT] key to select SPL.lo.
3.
Press the [TARE] key to weigh samples (which quantity is known) weight,
calculate piece weight.
4.
When SPL.Lo is shown, remove the sample on scale and press the [TARE]
key to confirm. Before scale is stable, SPL.Lo will be flashed. After it is stable,
it will go to next step.
5.
When SPL.Hi is shown, put samples (if quantity is known) onto the scale,
Press the [TARE] key to confirm reading weight. Before scale is stable,
SPL.hi will be flashed. After it is stable, it will go to next step.
5a.
If the calculated piece weight is less than 0.5d, the indicator will display
PWt.Er and go back to counting mode. Otherwise, after the reasonable piece
weight has been captured, the scale will go back to counting mode. The piece
weight will be saved and used again.
6.
After IN.PCS shown, L0000 will be displayed.
7.
Use the [UNIT] and [HOLD] keys to input the quantity of samples.
67XXU USB/Serial Scale Service Manual
21
4.5
8.
Press the [TARE] key to confirm the entry.
8a.
If the calculated piece weight is less than 0.5d, the indicator will display
PWt.Er and go back to counting mode. Otherwise, after the reasonable piece
weight has been captured, the scale will go back to counting mode. The piece
weight will be saved and used again.
9.
Press the [ZERO] key to exit and back to counting mode.
Hold Function
The HOLD function can be used to freeze a displayed number. In this mode, the scale
can capture a dynamic number, hold a stable number, or average a unstable number
and then HOLD (freeze) this number temporarily for the user to view or record.
The HOLD function can be used in normal weighing mode and counting mode. After
entering HOLD mode, the speed of A/D converter can be increased to 80Hz (if USERHOLD-AD.H.SP is set to YES) from original 10Hz for some dynamic weighing
applications.
It is possible to weigh restless samples such as live animals or moving objects within
the HOLD function. The indicator provides special mode settings to accommodate
weight movements.
4.5.1 Activate the Hold Function
l
The CONFG-FUNC-HOLD menu item must be set to YES.
Menu items of:
l
USER-HOLD-HLD.MD /AVG.TM /HLD.TM/RG /STB.TM
l
USER-OTHER-NLD.RG need be set to reasonable values.
l
To speed up sampling of weight, set USER-HOLD-AD.H.SP menu item to
YES.
4.5.2 Access the Hold Mode
To enter the HOLD mode, press the [HOLD] key while in the normal weighing mode or
counting mode.
4.5.3 Hold Methods
l
Positive Peak Number HOLD mode
l
Negative Peak Number HOLD mode
l
Toggle HOLD mode
l
Average HOLD mode
l
Auto HOLD mode
The following are details of these HOLD modes:
22
67XXU USB/Serial Scale Service Manual
Positive Peak HOLD
When USER-HOLD-HLD.MD is set to PS.PEK, the hold mode is positive peak hold
mode.
When scale first enters this working mode, it will display the largest positive number
that is from the time of zero-point set. The scale also will always catch the largest
positive number and display it.
To exit HOLD mode, press the [HOLD] key again.
Negative Peak HOLD
When USER-HOLD-HLD.MD is set to NG.PEK, the hold mode is in negative peak hold
mode.
When the scale first enters this mode, it will display the largest negative number from
the time of zero-point set. The scale also will always catch the largest negative number
and display it.
To exit HOLD mode, press the [HOLD] key again.
Toggle HOLD
When USER-HOLD-HLD.MD is set to TOGLE, the hold mode is toggled between
HOLD and MANUAL HOLD function.
After entering this mode, the scale will freeze and display a number if scale is stable.
Only the weight that is over USER-OTHER-NLD.RG (zero 'dead' band) can be held.
To exit HOLD mode, press the [HOLD] key again. If the time of the scale being unstable
is more than USER-HOLD-STB.TM, STB.ER will be shown.
Press the [TARE] key to start averaging again or press the [HOLD] key to exit.
Average HOLD
Set the USER-HOLD-HLD.MD parameter to AVERG.
After entering this mode the scale will freeze and display number if the scale is stable.
If the scale is not stable, but the variation is less than the USER-HOLD-DYN.RG
setting, the scale will average data in USER-HOLD-AVG.TM, then freeze and display
the number. Only the weight that is over USER-OTHER-NLD.RG can be frozen.
The scale will exit HOLD mode according to the setting of USER-HOLD-HLD.TM. If the
time of scale variation is over USER-OTHER-NLD.RG and is more than USER-HOLDSTB.TM, STB.ER will be shown.
Press [UNIT] or [TARE] to start averaging again, or press the [HOLD] key to exit.
Auto HOLD
Set the USER-HOLD-HLD.MD parameter to AUTO. Different items can be weighed
one after another without pressing any buttons.
After entering this working mode, scale will freeze and display number if scale is stable.
Only the weight that is over USER-OTHER-NLD.RG can be frozen. If the held weight
is moved away and a new load is put on the scale, the new load will automatically be
held.
67XXU USB/Serial Scale Service Manual
23
The scale will exit HOLD mode according to the setting of USER-HOLD-HLD.TM. If the
time of scale variation being over USER-OTHER-NLD.RG is more than USER-HOLDSTB.TM, STB.ER will be shown. Press the [TARE] key to start averaging again or
press the [HOLD] key to exit.
4.6
Display Software and Hardware Version
Display the current version of software and hardware.
4.7
4.8
24
1.
Enter the Setup Mode by pressing the [HOLD] + [ON/OFF] keys until confg
is displayed.
2.
Use the [UNIT] key to select the MISC-VER menu.
3.
Press [TARE] to display the current version.
3a.
Firmware Version display Format is: Vxx.yy, xx is hardware version, yy is
software version.
4.
Press the [ON/OFF] key to return to last menu item.
Display Test
1.
Press the [HOLD] + [ON/OFF] keys until confg is displayed.
1.
Use the [UNIT] key to select TEST-DSP.TS menu.
2.
Press [TARE] to enter the test display mode and all segments will light at first.
2a.
In this mode, every press of the [UNIT] key will light the next segment. Every
press of the [HOLD] key will light the next digit.
2b.
Press the [TARE] key to automatically light all segments and all digits.
3.
Press the [ON/OFF] key to return to last menu item.
Keyboard and Buzzer Test
1.
Press the [HOLD] + [ON/OFF] keys until confg is displayed.
2.
Use the [UNIT] key to select TEST-KEY.TS menu.
3.
Press [TARE] to enter test keypad mode and key will be displayed.
4.
Press any key. The value of this key will be displayed and the buzzer will beep.
5.
Press the [ON/OFF] key to return to last menu item.
67XXU USB/Serial Scale Service Manual
4.9
Serial Port 1/2 (COM1/2) Receiving Test
Before testing the receiving function of COM1 or COM2, a cable is need to connect a
computer to the scale. A terminal program such as Hyper Terminal is also needed for
testing.
Note: baud rate is selected by USER-COM1/2-BUD.RT, 8N1 byte format is fixed, Hex
data (0x00 - 0xff) are used.
1.
Press the [HOLD] + [ON/OFF] keys until confg is displayed.
2.
Use the [UNIT] key to select TEST-CM1.RD or TEST-CM2.RD item.
3.
Press [TARE] to enter test COM1/2 receiving function. rd1.-- or rd2.-- will
be displayed.
3a.
In this mode, received hex data (0x00 - 0xff) will be displayed in -- position.
4.
Press the [ON/OFF] key to return to last menu item.
4.10 Serial Port 1/2 (COM1/2) Transmitting Test
Before testing the receiving function of COM1 or COM2, a cable is need to connect a
computer to the scale. A terminal program such as Hyper Terminal is also needed for
testing.
Note: baud rate is selected by USER-COM1/2-BUD.RT, 8N1 byte format is fixed, Hex
data (0x00 - 0xff) are used.
1.
Press the [HOLD] + [ON/OFF] keys until confg is displayed.
2.
Use the [UNIT] key to select TEST-CM1.TD or TEST-CM2.TD item.
3.
Press [TARE] to enter test COM1/2 transmit function. td1.-- or td2.-- will
be displayed.
3a.
In this mode, transmitted hex data (0x00 - 0xff) will be displayed in -position.
4.
Press the [ON/OFF] key to return to last menu item.
67XXU USB/Serial Scale Service Manual
25
5
Setup Mode
The setup menu consists of five different sub-menus. Within each sub-menu are
different menu options.
The config/cal switch must be set in the ON position in order to make changes to
specific parameters.
5.1
5.2
Entering the Setup Menu
1.
Power on the indicator by pressing and holding the [ON/OFF] key.
2.
Press the [HOLD] + [ON/OFF] key for 3 seconds. The indicator shows
confg to indicate that you are in Setup Menu mode.
Navigating the Setup Menu
CONFG
USER
CAL
MISC
TEST
1.
Once Confg is displayed, use the [UNIT] key to move to forward through the
menu choices or the [HOLD] key to move backward in the setup menu.
2.
Use the [TARE] key to access the desired menu. (e.g. User)
3.
Use the [UNIT] key to view the available sub-menus (parameter: e.g. beep).
4.
Use the [TARE] key to select the sub-menu.
5.
Use the [UNIT] key to view the choices within the sub-menu. (e.g. key)
6.
Press the [TARE] key to select the desired choice within the sub-menu. Once
selected the parameter will be displayed.
7.
Press [ZERO] to return back up and return to the setup menu.
Table 5.1 Key Navigation
[HOLD/PRINT]
[UNIT]
Access the Setup Menu.
Scroll through available menus.
Choose a sub-menu
Make a change within the sub-menu
[ZERO/ON/OFF]
Scroll through available menus.
Choose a sub-menu
Make a change within the sub-menu
[TARE]
26
Choose a sub-menu
67XXU USB/Serial Scale Service Manual
5.3
Setup Menu Parameters
This section provides more detailed descriptions of the selections found in the Setup
Menu.
The menu charts show the flow of the parameters and also provide a quick reference
to the parameters within the menu.
The menu tables show the submenus, options and default parameter in LCD display
format to coincide with the actual display.
5.3.1 CONFG Menu
CF.ON
CF.OFF
RESET
No
REGUL
Yes
PRIM.D
USA
10.DSP
Yes
Canada
Europe
kg
0.0001
0.0002
0.0005
SECD.N
PRI.Ut
100 – 20,000
none
No
PRIM.N
100 – 25,000
lb
0.001 0.002
0.005
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
MOTION
OVER.D
1 - 255
0 - 100
UNITS
kg
lb
oz
No
ZRO.PT
IZSM
IN.IZS *
0 - 100
WEGHT
CAL.ZR
AZSM
0 - 100
WEGHT
FT1.ST
0 - 255
FT2.TH
Yes
HOLD
COUNT
COMPR
GE.CAL
Yes
WT.ADJ
No
0 - 255
Weak
CAL.ZR
FT2.ST
0 - 255
0 - 100
LST.Z.T
DP.OVR
FT1.TH
g
FUNC
FLTER
OV.IZS * SAZSM
lb:oz
Midle
Stong
LST.Z.T
* only appears if “Regul” is set to None
Figure 5.1 CONFG Menu Chart
The figure above is an illustration of the available menus with the CONFG menu and
the choices within those menus. Refer to Table 5.2 for explanations of the menu
choices.
67XXU USB/Serial Scale Service Manual
27
Table 5.2 CONFG Menu Choices and Explanations
CONFG
SubMenu1
SubMenu2
Option
Default
CF.ON
CF.OFF
RESET
Seal switch position
NO
none
USA
Canda
Comment
The display will show whether the
seal switch is in the ON or Off
position. This parameter can’t be
changed within the software.
NO
Reset Confg menu
parameters to default
setting
USA
Select the standard in
which the scale will
comply: USA, Canada,
Europe
*None = not legal for trade.
YES
REGUL
Parameter Description
Eurpe
PRIM.N
100 20000
Primary full scale value
Default full scale value will depend
on capacity of scale.
*If (REGUL) ≠ none, the max is
10,000
PRIM.D
0.0001
The division value under
primary unit
Default division size will depend on
capacity of scale.
The division value under second
unit is automatically determined by
the indicator according to the
division value under primary unit.
0.0002
0.0005
0.001
0.002
0.005
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
28
67XXU USB/Serial Scale Service Manual
CONFG
SubMenu1
SubMenu2
PRIM.Ut
Option
Default
kg
lb
Parameter Description
Primary unit
Select the primary unit from kg or lb.
The second unit is lb if kg is
selected as the primary unit.
*The calibration standard weight
must be in the primary unit!
Second scale full scale
value
The division number under second
unit. The maximum is
1.25*(PRIM.N).
*If (REGUL)≠none, the max is
10,000
NOTE: Secondary division has to
match the primary division.
Display weight at 10
times division number
under primary unit
*If (REGUL)= none this parameter
will not be available.
When yes is selected, some
menus will not be active.
lb
SECD.N
10025000
10.DSP
NO
NO
YES
Comment
MOTON
1-255
4
Motion window
1-255 = ±0.25d *(1-255)
*If (REGUL)=none, the max is 12
OVER.D
0-100
0
Overload display
limitation
0=FS+9d
1-100=101%FS -200%FS.
*If (REGUL)=none, the max is 10
yes
yes
UNITS key
YES = enable this unit
No = disable this unit
UNITS
KG
no
lb
yes
yes
In trade applications, lb:oz is not
allowed
no
oz
yes
yes
no
lb:oz
yes
no
no
g
yes
yes
no
67XXU USB/Serial Scale Service Manual
29
CONFG
SubMenu1
SubMenu2
Option
Default
ZRO.PT
IZSM
0-100
10
IN.IZS
WEGHT
WEGHT
OV.IZS
FLTER
Parameter Description
Comment
Initial zero set
mechanism
Range of capacity in percent
± 0 - 100%FS
Also uses SAZSM and AZSM (total)
*If (REGUL)=none, the max is 10
Inside IZSM
WEIGHT= on power up
CAL.ZR
CAL.ZR= calibration zero point
LST.Z.T
LST.Z.T=store last push button zero
and push button tare
*If (REGUL) ≠none, the value is
fixed on WEIGHT
DP.OVR
DP.OVR
Outside IZSM
DP.OVR=display initial zero is over.
Display will show upper dashes
when above capacity
WEGHT
WEIGHT= current weight
Can zero more weight (approx 90%)
before dashes are displayed. Not
Legal for Trade
CAL.ZR
CAL.ZR= calibration zero point
will display dashes at 100%
LST.Z.T
LST.Z.T=Last ZERO and TARE
SAZSM
0-100
2
Zero key range
0=no limitation
1-100= (initial zero point) ±1%FS (initial zero point) ±100%FS
*If (REGUL) ≠none, the max is 2
AZSM
0-100
8
Zero tracking window
0=0d, no tracking
1-100=±(0.2+0.05*(1-100))d /s
*If (REGUL) ≠none, the max is 4
FT1.TH
0-255
40
Digital filter1 threshold
0=no filter1
1-254=filter1 used only when
vibration in ±0.25d*(1-254)
255= filter1 always used
FT1.ST
weak
midle
Digital filter1 intensity
Weak = 4 weights to average
Midle = 8 weights to average
Strong = 16 weights to average
midle
stong
30
FT2.TH
0-255
8
Digital filter2 threshold
0=no filter2
1-254=filter2 used only when
vibration in ±0.25d*(1-254)
255= filter2 always used
FT2.ST
0-255
240
Digital filter2 intensity
0-255=weak to strong
67XXU USB/Serial Scale Service Manual
CONFG
SubMenu1
SubMenu2
Option
Default
FUNC
HOLD
YES
YES
YES
YES
NO
NO
Enable or disable
counting function
YES
NO
no
Enable or disable data
comparison function
YES
NO
NO
Enable or disable the
geographical adjustment
factor
YES
NO
NO
Enable or disable weight
fine-tuning using keypad
in weighing mode
YES
NO
*If (REGUL) ≠none, this item is
NO
NO
COMPR
YES
NO
ge.cal
yes
no
WT.ADJ
YES
no
Comment
Enable or disable hold
function
NO
COUNT
Parameter Description
*The setting will be limited by the choice of REGUL
67XXU USB/Serial Scale Service Manual
31
5.3.2 USER Menu
RESET
No
USB
USB
COM1
OUT1
Yes
BUD.RT
1200
2400
4800
9600
19200
BT.FMT
OUT.MD
38400
8N1
NONE
MULTI
701
SCP01
SCP02
CONT
PRINT
CMD
PRT.CD
STABL
ST.NLD
9-pin
OUT2
OUT.MD
TARE
NET
COUNT
AD.CDE
BT.VOL
STAUS
B.LINE
SCP03
EH-SCP
IBM
NONE
9-pin
BT.FMT
GROSS
PCWT
7E1
COM2
BUD.RT
SCL.ID
LYOUT
LYOUT
NLD
LINE1
LINE2
LINE3
PR.NLD
BEEP
SCL.ID
GROSS
TARE
NET
COUNT
PCWT
AD.CDE
BT.VOL
STAUS
B.LINE
KEY
No
1200
2400
4800
9600
19200
38400
MULTI
SCP01
SCP02
SCP03
EH-SCP
NONE
701
NONE
7E1
CONT
PRINT
CMD
PRT.CD
STABL
ST.NLD
NLD
LINE1
LINE2
LINE3
No
HLD.MD
Yes
AVG.TM
STB.TM
1 - 60
HLD.TM
HLD.RG
NLD.RG
HD.KEY
HOLD
PRINT
NG.PEK
TOGLE
AVERG
CMD.SR
LEGACY
1 - 255
HLD.PR
No
0-255
NONE
PS.PEK
L.LOW
IN.LMT
O.HIGH
OUT.LT
LINE4
OTHER
0-65535
3*AVG.TIM-255
NONE
Yes
PR.NLD
HOLD
AD.H.SP
COMPAR
IBM
NONE
8N1
LINE4
COM.1
COM.2
A.OFF.T
LCD.BL
0 - 255
0 - 255
TA.KEY
COM1-2
SCL.ID
000000-999999
Yes
AUTO
PHD.RG
0-8
No
Yes
Figure 5.2 USER Menu Chart
The figure above is an illustration of the available menus with the USER menu and the
choices within those menus. Refer to Table 5.3 for explanations of the menu choices.
Table 5.3 User Menu Choices and Explanations
USER
SubMenu1
RESET
SubMenu2
Option
Default
Parameter Description
NO
NO
Reset User menu parameters to
default setting
YES
32
Comment
67XXU USB/Serial Scale Service Manual
USER
SubMenu1
SubMenu2
Option
Default
COM1
(USB)
BUD.RT
1200
9600
Parameter Description
Comment
Select COM1 baud rate
2400
4800
9600
19200
38400
BT.FMT
OUT.MD
8N1
8N1
Select COM1 byte format
(1) 8N1=8 data bits, No parity check
bit, 1 stop bit
7O1
(2) 7O1=7 data bits, 1 Odd parity
check bit, 1 stop bit
7E1
(3) 7E1=7 data bits, 1 Even parity
check bit, 1 stop bit
none
CONT
PRINT
CMD
PRt.cd
Select COM1 output mode
(1) NONE=no communication
(2) CONT=continuously output
(3) PRINT=output after [PRINT] key
is pressed
(4) CMD=output after a request
command is received
PRT.CD
(5) PRT.CD= output after [PRINT]
key is pressed or request command
received
STABL
(6) STABL=Sends output
automatically after scale is stable.
Note: use PRINT or CMD to output
data, the scale must be stable
ST.NLD
**(7) ST.NLD=output after scale has
returned to zero range
(OTHER>NLD.RG) and is stable.
NLD
**(8) NLD= Output after scale has
returned to zero range
(OTHER>NLD.RG) and does not
wait for the scale to be stable.
Pr.nld
(9) PR.NLD= Manual push button
print once after scale is stable.
Scale has to return to zero range
(OTHER>NLD.RG) before another
push button print command can be
executed.
**Note: If PRINT, STABL, ST.NLD, LNLD or CMD are used to output data, the scale must be stable.
67XXU USB/Serial Scale Service Manual
33
USER
SubMenu1
SubMenu2
Option
Default
LYOUT
MULTi
multi
Comment
Set COM1 content and format
(1) MULTI= the following selected
item in OUT1 will be output use
defined format
scp01
Emulates NCI protocol
(2) SCP01= only displayed content
and current status will be output, it's
compatible with NCI-SCP01
scp02
Emulates ECR protocol
(3) SCP02= only displayed content
and current status will be output.
Compatible with ECR-SCP02
scp03
Emulates Toledo 8213 protocol
(4) SCP03= only displayed content
and current status will be output.
Compatible with 8213-SCP03
Emulates Toledo PS60
(5) EH-SCP= command response
mode (PS-60)
IBM SCP03 protocol
(6) IBM= only displayed content
and current status will be output.
Compatible with NCI-SCP08
eh-scp
IBm
34
Parameter Description
67XXU USB/Serial Scale Service Manual
USER
SubMenu1
SubMenu2
Option
Default
OUT1
(USB)
SCL.ID
YES
NO
YES
Comment
Enable or disable scale ID
number
Prompt is "SCALE ID"
yes
Enable or disable gross weight
Prompt is "GROSS"
yes
Enable or disable tare weight
Prompt is "TARE"
YES
Enable or disable net weight
Prompt is "NET"
NO
Enable or disable counts
Prompt is "QUANTITY"
NO
Enable or disable piece weight
Prompt is "PIECE WT"
NO
Enable or disable ADC code
Prompt is "A/D CODE"
NO
Enable or disable whether to
display the battery voltage
Prompt is "VOLTAGE"
NO
Enable or disable scale status
Prompt is "STATUS"
How many blank lines after
strings output
NONE=no blank line
NO
GROSS
Parameter Description
NO
TARE
YES
NO
NET
YES
NO
COUNT
YES
NO
PcWT
YES
NO
AD.CDE
YES
NO
BT.VOL
YES
NO
STAUS
YES
NO
B.LINE
NONE
LINE1
LINE2
LINE1
LINE1/2/3/4=there are 1, 2,3 or 4
blank lines after strings, used for
paper feed forward 1/2/3/4 lines.
LINE3
LINE4
67XXU USB/Serial Scale Service Manual
35
USER
SubMenu1
SubMenu2
Option
Default
COM2
(9 Pin)
BUD.RT
1200
9600
Parameter Description
Comment
Select COM2 baud rate
2400
4800
9600
19200
38400
BT.FMT
OUT.MD
8N1
7e1
Select COM2 byte format
(1) 8N1=8 data bits, No parity check
bit, 1 stop bit
7O1
(2) 7O1=7 data bits, 1 Odd parity
check bit, 1 stop bit
7E1
(3) 7E1=7 data bits, 1 Even parity
check bit, 1 stop bit
none
CONT
PRINT
CMD
PRT.CD
Select COM2 output mode
(1) NONE=no communication
(2) CONT=continuously output
(3) PRINT=output after PRINT key
pressed
(4) CMD=output after a request
command is received
PRT.CD
(5) PRT.CD= output after PRINT
key pressed or request command
received
STABL
(6) STABL=output after scale is
stable; Note: use PRINT or CMD to
output data, the scale must be
stable
st.nld
**(7) ST.NLD=output after scale has
returned to zero range and is
stable. (OTHER>NLD.RG)
nld
**(8) NLD= Output after scale has
returned to zero range and does not
wait for the scale to be stable.
(OTHER>NLD.RG)
Pr.nLD
(9) PR.NLD= Manual push button
print once after scale is stable.
Scale has to return to zero range
(OTHER>NLD.RG) before another
push button print command can be
executed.
**Note: If PRINT, STABL, ST.NLD, LNLD or CMD are used to output data, the scale must be stable.
36
67XXU USB/Serial Scale Service Manual
USER
SubMenu1
SubMenu2
Option
Default
LYOUT
MULTi
multi
Parameter Description
Comment
Set COM2 content and format
(1) MULTI= the following selected
item in OUT2 will be output use
defined format
Scp01
Emulates NCI protocol
(2) SCP01= only displayed content
and current status will be output, it's
compatible with NCI-SCP01
scp02
Emulates ECR protocol
(3) SCP02= only displayed content
and current status will be output, it's
compatible with ECR-SCP02
scp03
Emulates Toledo 8213 protocol
(4) SCP03= only displayed content
and current status will be output, it's
compatible with 8213-SCP03
Emulates Toledo PS60
(5) EH-SCP= command response
mode (PS-60)
IBM SCP03 protocol
(6) IBM= only displayed content
and current status will be output.
Compatible with NCI-SCP08
eh-scp
Ibm
67XXU USB/Serial Scale Service Manual
37
USER
SubMenu1
SubMenu2
Option
Default
OUT2
(9 Pin)
SCL.ID
YES
NO
YES
Comment
Enable or disable scale ID
number
Prompt is "SCALE ID"
yes
Enable or disable gross weight
Prompt is "GROSS"
yes
Enable or disable tare weight
Prompt is "TARE"
YES
Enable or disable net weight
Prompt is "NET"
NO
Enable or disable counts
Prompt is "QUANTITY"
NO
Enable or disable piece weight
Prompt is "PIECE WT"
NO
Enable or disable ADC code
Prompt is "A/D CODE"
NO
Enable or disable whether to
display the battery voltage
Prompt is "VOLTAGE"
NO
Enable or disable scale status
Prompt is "STATUS"
How many blank lines after
strings output
NONE=no blank line
NO
GROSS
Parameter Description
NO
TARE
YES
NO
NET
YES
NO
COUNT
YES
NO
PcWT
YES
NO
AD.CDE
YES
NO
BT.VOL
YES
NO
STAUS
YES
NO
B.LINE
NONE
LINE1
LINE2
LINE1
LINE1/2/3/4=there are 1, 2,3 or 4
blank lines after strings, used for
paper feed forward 1/2/3/4 lines.
LINE3
LINE4
38
67XXU USB/Serial Scale Service Manual
USER
SubMenu1
SubMenu2
Option
Default
BEEP
KEY
YES
YES
NO
COMPR
NONE
IN.LMT
Parameter Description
Comment
Enable or disable beep after a
key is pressed.
(1) NONE = no beep
L.LOW
(2) L.Low = beep when lower than
low limitation;
IN.LMT
(3) IN.LMT = beep when in range of
low and high limitation
O.HIGH
(4) O.HIGH = beep when over high
limitation
OUT.LMT
67XXU USB/Serial Scale Service Manual
(5) OUT.LMT = beep when lower
than low limitation or higher than
high limitation
39
USER
SubMenu1
SubMenu2
Option
Default
Parameter Description
HOLD
AD.H.SP
YES
NO
Enable or disable use of the
high speed A/D converter after
entering the HOLD mode
NO
HLD.MD
NONE
auto
Hold mode
(1) NONE= off
PS.PEK
(2) PS.PEK=Positive Peak number
Hold mode. Scale will display and
refresh the positive peak value from
last zero setting.
NG.PEK
(3) NG.PEK=Negative PEAK
number Hold mode. It is similar to
PS.PEK, but a negative number is
used.
TOGLE
(4) TOGLE=Press [HOLD] key to
enter HOLD mode. Stores the
display value. Will stay on the
display for the duration of time set
at HLD.TM.
AVERG
(5) AVERG= Average HOLD mode.
Time it looks at the weight before
updating the display. Set by
AVG.TM. Weight or vibration must
fall within window of HLD.RG also.
AUTO
40
Comment
(6) AUTO=Auto hold mode. It is
similar to AVERAG mode, but will
allow more weight to be added.
AVG.TM
1-60
3
Average data time for HOLD
mode
1-60 seconds
STB.TM
3XAVG.TIM
- 255
3X
AVG.TIM
Wait time for the scale to be
stable in HOLD mode
Window which has to be 3 times
larger than AVG.TM
HLD.TM
0-65535
0
Data HOLD time
0=data will be frozen until HOLD
key pressed.
1-65535=data frozen time is 165535s, after the time elapses,
scale will exit HOLD mode.
HLD.RG
0-255
5
Hold range
Window of vibration for Auto to
work.
0=any data can be averaged
1-255= only the data which
vibration is in 1-255d can be
averaged and held.
hd.key
hold
hold
HOLD/PRINT key
(1) HOLD= only HOLD key
print
(2) PRINT= only PRINT key
hld.pr
(3) HLD.PR= HOLD and PRINT key
67XXU USB/Serial Scale Service Manual
USER
SubMenu1
SubMenu2
Option
Default
OTHER
NLD.RG
1-255
10
CMD.SR
NONE
COM1.2
Parameter Description
No hold range
Load must return to zero in
divisions to perform a print when in
AUTO.
1-255=the range of weight is 1255d. When current weight is less
than this value, the scale can be
regarded as empty, or the load on
scale is removed.
It must be bigger than
(CONFG.MOTON).
Command source
Turns COM1 / COM2 on/off
(1) NONE=no any command will be
executed
COM.1
(2) COM.1= command from COM1
will be executed
COM.2
(3) COM.2= command from COM2
will be executed
COM1.2
Legacy
Comment
0-2
(4) COM.1.2= command from
COM1 or COM2 will be executed
1
Status bit setting
0=no change to output string. Can
send 3 or 4 status bits
1=all data sent ot has 2 status bits =
bit 6. Character 2 must be set to 0
2=all data sent out has 3 status bits
and 7 weight characters.
A.OFF.T
0-255
0
LCD.BL
0-255
30
TA.key
yes
yes
Auto off time
0=not auto power off
1-255=auto power off after 1-255
minutes. In this period, no operation
or no weight change
LCD backlight set
(1) 0=always off
(2) 1=always on
(3) 2=press down ZERO+UNIT
together more than 3s to turn on or
turn off
(4) 3-255=auto on when key
operation or weight changing. Auto
off after 3-255s elapsed.
Tare key enable
Yes= tare key is enabled
no
No= tare key is disabled
phd.rg
0-8
0
Photo eye TARE sensitivity
SCL.ID
000000999999
123456
Scale ID number: 000000999999
67XXU USB/Serial Scale Service Manual
(1) 0= remote TARE key disabled
(2) 1-8 = sensitivity level
1= close distance - 8= long distance
41
5.3.3 CAL Menu
CAL.ON
CA.OFF
ZERO
LINE
GEO
CODE
INPUT
GRAVT
00-70
9.761839.99999
CAL.PO
CAL.P1
END.Y
Yes
No
CAL.P2
END.Y
Yes
CAL.P3
No
Figure 5.3 CAL Menu Chart
The figure above is an illustration of the available menus with the CAL menu and the
choices within those menus. Refer to Table 5.4 for explanations of the menu choices.
Table 5.4 CAL Menu Choices and Explanations
CAL
Submenu1
42
Submenu2
Option
Parameter Description
Comment
CAL.ON
CA.OFF
Seal switch position
The display will show whether the
seal switch is in the ON or Off
position. This parameter can’t be
changed within the software.
ZERO
Zero point calibration
Only do zero point calibration, then
go to CAL.END to end (only need
where a zero shift has occurred).
67XXU USB/Serial Scale Service Manual
CAL
Submenu1
Submenu2
Option
LINE
CAL.P0
Line calibration point0
Do zero point calibration. This point
can't be omitted.
CAL.P1
Line calibration point1
First weight point calibration. This
point can't be omitted and standard
weight must be over 10%FS.
End calibration?
YES=go to CAL.END to end
NO=go to do next point calibration
Line calibration point2
Second weight point calibration.
Standard weight must be over
10%FS and be larger than it in
CAL.P1. This point can be omitted.
End calibration?
YES=go to CAL.END to end
NO=go to do next point calibration
Line calibration point3:
Third weight point calibration.
Standard weight must be over
10%FS and be larger than it in
CAL.P2, this point can be omitted.
Code 00-70
END.Y
YES
Parameter Description
NO
CAL.P2
END.Y
YES
NO
CAL.P3
geo
code
00-70
Select geograhical position
gravt
9.761839.99999
Input gravity of user location
input
67XXU USB/Serial Scale Service Manual
Input or view calibration
parameter values
Comment
Only used to copy calibration
parameters from one scale to a new
scale.
43
5.3.4 MISC Menu
CODE
VOL
VER
Figure 5.4 MISC Menu Chart
The figure above is an illustration of the available menus with the MISC menu. There
are no programming choices within this menu. Refer to Table 5.5 for explanations of
the menu choices.
Table 5.5 MISC Menu Choices and Explanations
MISC
Submenu1
CODE
Remark
Display A/D counts = approximately 100,000 counts per mV
VOL
Display voltage; calibrate voltage; set full charged voltage and low battery voltage
VER
Display firmware version
5.3.5 TEST Menu
DSP.TS
CM1.RD
CM1.TD
CM2.RD
CM2.TD
KEY.TS
Figure 5.5 TEST Menu Chart
The figure above is an illustration of the available menus with the TEST menu. There
are no programming choices within this menu. Refer to Table 5.6 for explanations of
the menu choices.
Table 5.6 TEST Menu Choices and Explanations
TEST
Submenu1
44
Remark
dsp.ts
Test LCD
cm1.rd
Test COM1 receiving
cm1.td
Test COM1 transmitting
cm2.rd
Test COM2 receiving
cm2.td
Test COM2 transmitting
KEY.ts
Test keys and buzzer
67XXU USB/Serial Scale Service Manual
5.4
Exit the Setup Menu
1.
Power off the indicator by pressing and holding the [ON/OFF] key.
2.
Turn the indicator back on by pressing the [ON/OFF] key. The display will go
through a digit check, then settle into the normal operating mode. All front
panel keys will now return to their normal mode of operation.
67XXU USB/Serial Scale Service Manual
45
6
Calibration
The configuration/calibration button must be pushed in order to calibrate the scale.
Refer to Chapter 8 for details on push button location.
NOTE: More than 10% of the full scale weight is needed for calibration.
NOTE: Press the [ON/OFF] key to return to the last sub-menu.
6.1
Enter the Calibration Mode
1.
Access the setup mode by pressing the [HOLD]+[ON/OFF] key for 3 seconds.
2.
Use the [HOLD] key to select the CAL menu.
3.
Press the [TARE] key to enter the calibration mode.
3a.
After entering this mode, the number of calibrations will be shown first. This
number will be increment one digit after every calibration and calibration data
saved. This counter can't be modified or erased. It counts from 0000 to 9999,
when 9999 is reached, the counter starts over at 0000.
4.
After the counter number was displayed, it will show "Ca.OFF" or "CAL.ON"
which depends on whether the sealed calibration switch is OFF or ON. If the
switch is OFF, the following steps can be done, but the result will not be
saved.
5.
Press the [TARE] key to go to next step.
6.1.1 Zero Point
46
1.
When ZERO is displayed, press the [UNIT] key to select Zero Point calibration.
2.
Once ZERO is selected, remove all weight on the scale.
3.
Press [TARE] to confirm.
4.
The ZERO will flash while capturing the zero point. After getting reasonable
data, it automatically saves the change and exits to the weigh mode.
67XXU USB/Serial Scale Service Manual
6.1.2 Linearity
The scale linearity can be calibrated with a zero reference and a full scale reference or
multiple linearity weight values. The linearity calibration is determined by the settings
in the CAL-LINE parameter.
1.
When LINE is selected, press the [TARE] key to enter linearity calibration.
2.
CAL.P0 will be displayed with a zero value. Remove all weight on the scale
and then press the [TARE] key to confirm zero point calibration. The zero
weight will flash while capturing the zero point. After getting the reasonable
zero-point data, the zero weight will become steady.
3.
The first default standard weight is displayed after CAL.P1 being shown. Put
the corresponding weight (more than 10%FS weight) onto scale. The default
standard weight is 100%FS.
4.
Use the [HOLD] and [UNIT] keys to input the value of the loaded weight.
5.
Press the [TARE] key to confirm.
5a.
The indicator will flash the input standard weight. When the weight becomes
steady the indicator will automatically go to next step. If this point can't be
calibrated correctly CAL.Er will be displayed. It is possible the weight load
onto scale is too small or the input data is incorrect. Repeat the previous steps.
6.
When End.y is shown and the y is flashing, it is waiting to exit calibration or go
on next calibration point. Use the [UNIT] key to select yes or no.
7.
Press the [TARE] key to confirm.
7a.
If yes is selected, the calibration will be saved and exit to the weigh mode.
7b.
If no is selected, it will go to next step.
8.
When 100% of the full scale weight is displayed after CAL.P2 is shown, it will
be calibrated on standard weight for the second point.
9.
Use the [HOLD] and [UNIT] keys to input the value of the loaded weight (more
than 10% FS weight, and larger than the weight used on CAL.P1) onto scale.
10.
When End.y is shown and the y is flashing, it is waiting to exit calibration or go
on next calibration point. Use the [UNIT] key to select yes or no.
11.
Press the [TARE] key to confirm.
12.
When 100% of the full scale weight is displayed after CAL.P3 is shown, it will
be calibrated on standard weight for the third point.
13.
Use the [HOLD] and [UNIT] keys to input the value of the loaded weight (more
than 10% FS weight, and larger than the weight used on CAL.P2) onto scale.
14.
When End.y is shown and the y is flashing, it is waiting to exit calibration or go
on next calibration point. Use the [UNIT] key to select yes or no.
15.
Press the [TARE] key to confirm.
16.
When calibration is complete CA.End will be displayed. The indicator will restart and go back to the weigh mode.
67XXU USB/Serial Scale Service Manual
47
6.2
Geographical Adjustment
1.
When GEO is selected, press the [TARE] key to enter Geographical
Adjustment.
2.
When CODE is displayed, press the [UNIT] key to select geographical position
code or input user local gravity value directly.
3.
When CODE is selected, choose the position code of the scale being used
(00-70) according to the elevation and latitude from Table 6.1 by using the
[HOLD] and [UNIT] keys.
4.
Press [TARE] key to confirm.
CAUTION! Only an authorized manufacturer representative or certified
verification personnel may make these changes. Changing the Geographical
setting alters the calibration values!
48
67XXU USB/Serial Scale Service Manual
Table 6.1 Location Code For Elevation and Latitude
67XXU USB/Serial Scale Service Manual
49
6.3
Gravity Value
1.
When GRAVT is selected, press the [HOLD] and [UNIT] keys to input the
gravity value of the position that scale is used (9.76183-9.99999).
2.
Press the [TARE] key to confirm.
NOTE: Only an authorized manufacture representative or certified verification
personnel may make these changes.
6.4
Input or View Calibration
1.
When INPUT is selected, press the [TARE] key to enter Input calibration
parameter values that were previously received or view current calibration
parameter values.
All parameters regarding calibration are divided to 12 pages and are displayed on LCD
by "nn:xxxx" format ("nn" is a decimal number of page, "xxxx" is an hexadecimal value
of parameter. (e.g. 02:85E2).
01-02 pages: zero code
03-04 pages: standard weight of CAL.P1
05-06 pages: codes of CAL.P1
07-08 pages: standard weight of CAL.P2
09-10 pages: codes of CAL.P2
11-12 pages: full capacity net code
50
2.
When no digits are blinking on the display, this means calibration parameters
value are being viewed. Use the [HOLD] key to view the next page.
3.
When parameter values are being viewed, press the [HOLD] key for more
than 3 seconds to modify.
4.
When first digit is blinking, this means the value is being modified. Press the
[HOLD] key to make next digit flash (if current flashing position is the last one
the next page value will be shown).
5.
Press the [HOLD] and [UNIT] keys to input the number.
6.
Press the [TARE] key to confirm.
7.
After the indicator gets all needed data, it will calculate and store all calibration
parameters into EEPROM or after finishing calibration, it will display CAL.nd.
8.
The scale will re-start and go back to original mode.
67XXU USB/Serial Scale Service Manual
6.5
Weight Fine-tune
With this function, the user can adjust displayed weight a little without the need of
standard weight. But please note:
6.6
l
The scale must have been calibrated previously
l
The range of adjustment is "(current displayed weight) x (0.9-1.1)". This
means the range is about ±10%
l
The CONFG-REGUL=NONE and CONFG-FUNC-WT.ADJ=YES must be
set.
1.
To enter this mode, turn on indicator. After the indicator displays a 0 weight,
place weight onto scale. The indicator will display the weight.
2.
Press down [TARE] and [ZERO] at same time until the first digit flashes, this
means indicator has entered into "weight fine-tune" mode.
3.
Use the arrow keys to input correct weight.
4.
Press the [TARE] key to confirm. The active correct weight will be displayed.
The displayed weight will be adjusted by this ratio (130.0/1234.5). The ratio
will be active until the next modification.
5.
Recalibrate the scale or use the Weight Fine Tune method to readjust the
ration.
Display ADC Output Code
In this mode, you can examine the stability of weighing system and increment the ADC
output code corresponding to the loaded weight. Please note the following:
l
The increment of ADC code for full scale weight must be larger or equal to
10 times of selected display division. Otherwise, the calibration cannot be
properly completed.
m
l
e.g. The display division is 0.1kg. Load 100kg standard weight on the
platform, the increment of ADC code should be at least more than
10x100kg/0.1kg= 10x1000=10000. In this case, the scale can be
calibrated. Otherwise, a smaller division needs to be chosen.
The variation of the ADC code should be small. Otherwise, the calibration
cannot be properly completed.
1.
From the weigh mode press the [HOLD] + [ON/OFF] key until CONFG is
shown.
2.
Use the [UNIT] and [TARE] keys to go to MISC - Code.
3.
Press the [TARE] key to enter this mode and display the ADC output raw
code.
4.
Press the [TARE] key to set the current code as a reference zero and then
display net code
5.
Press [TARE] again to clear this reference and display gross code.
6.
In this mode, press the [UNIT] key to select displaying code that has been
filtered by no-filter, filter1 and filter2.
7.
Press the [ON/OFF] key to exit this mode.
67XXU USB/Serial Scale Service Manual
51
7
Serial Communication
7.1
Communication Settings
52
1.
Power on the indicator by pressing and holding the [ON/OFF] key. The display
will go through a display test then go into regular weigh mode.
2.
Press the [HOLD] + [ON/OFF] key for 3 seconds. The indicator shows
confg to indicate that you are in Setup Menu mode.
3.
Press the [UNIT] key until the indicator display shows user.
4.
Press the [TARE] key and the indicator display shows reset.
5.
Press the [UNIT] key until you see the com port you are using for your
software; com1 (USB port) or com2 (serial port)
6.
Press the [TARE] key to select the desired com port.
7.
The indicator's display shows bud.rt. Press the [TARE] key go into the baud
rate setting and confirm it is approprioate baud rate for your software. To
toggle to another baud rate setting, press the [UNIT] key until the one is
displayed. (i.e. 1200, 2400, 4800, 9600, 19200, 38400)
8.
Press the [TARE] key and the display shows bud.rt. Press the [UNIT] key
and the display shows bt.fmt. Press the [TARE] key to go into the setting
and confirm it is the approprioate bit format for your software. To select
another bit format setting, press the [UNIT] key until the desired selection is
displayed. (i.e. 8n1, 7E1, 7O1)
9.
Press the [TARE] key and the display shows bt.fmt. Press the [UNIT] key
until the display shows lyout.
10.
Press the [TARE] key to go into your selection and press the [UNIT] key until
the display shows correct protocol needed for your software. *Most common
as follows scp01 = NCI protocol, scp02 = ECR protocol, scp03 = Toledo
8213 or ibm = IBM protocol.
11.
Press the [TARE] key and lyout will be displayed.
12.
Press the [ZERO] key to display the com port that you were changing.
13.
Press the [UNIT] key until the display shows other.
14.
Press the [TARE] key until the display shows nld.rg.
15.
Press the [UNIT] key until legacy is displayed.
16.
Press the [TARE] key and a number will be displayed.
17.
Press the [UNIT] key until a 2 is displayed.
18.
Press the [TARE] key and legacy will be displayed.
19.
Press and release the [ZERO/ON/OFF] key until you are all the way out of the
Setup Menu mode and into the Normal Weigh mode.
20.
Test scale with software. If scale fails communication, contact Brecknell Tech
Support at 800-242-2807 for further testing.
67XXU USB/Serial Scale Service Manual
7.2
Com Port 1
COM1 is a USB port used as a virtual RS-232 port. Communication wires come from
the USB connector and TXD0, RXD0 and GND.
7.3
Com Port 2
COM2 is a RS-232 bi-directional port. Communication wires are connected to the RS232 connector using TXD1, RXD1 and GND. Refer to page 10 for connection details.
7.4
Protocol
The baud rate and byte format is set by USER-COM-BUD.RT and USER-COMBT.FMT.
Responses to serial commands will be immediate or within one weight measure cycle
of the scale. One second should be adequate for use as a time-out value by remote
(controlling) device.
7.5
Transaction String
The length of each item in a transition string:
l
Reading data --- 6 bytes
l
Data polarity ----1 byte: "-" for negative, and followed the first digit; " " for
positive.
l
Decimal point ---1 byte: "."
l
Measure unit ----1-5 bytes:" lb"," kg","lb:oz","pcs","%". Units are always
lower case, left aligned
l
Current status-- 4 bytes
m
If the weight is over capacity, the scale will return eight "^" characters
(the field of polarity, decimal point, weight data is filled by "^").
m
If the weight is under capacity, it will return eight "_" characters (the field
of polarity, decimal point, and weight data is filled by "_").
m
If the zero point is error, it will return eight "-" characters (the field of
polarity, decimal point, and weight data is filled by "-").
Useless leading 0 before digits is suppressed. Reading weight is right aligned.
Table 7.1 Symbols Used
<LF>
Line Feed character (hex 0AH)
<CR>
Carriage Return character (hex 0DH)
<ETX>
End of Text character (hex 03H)
<SP>
Space (hex 20H)
H1H2H3 H4
Four current status bytes
<P>
Polarity character: "-" or " "
67XXU USB/Serial Scale Service Manual
53
W1---W6
Reading data, 1-6 bytes (six digits)
<DP>
Decimal point
U1U2 U3U4U5
Measure units, kg, lb, lb:oz, % or pcs; 2-5 bytes
<Add>
Address of scale; 2 bytes (00-99)
<Prompt>
Prompt characters of output content; max. 11bytes
Table 7.2 Bit Definition of H1H2H3 H4
Bit
0
Byte 2 (H2)
Byte 3 (H3)
00 = normal weighing
01 = count weighing
10 = percent weighing
11 = other mode
0 = RAM ok
0 = ROM ok
0 = gross weight
0 = not in HOLD
1 = RAM error
1 = ROM error
1 = net weight
1 = in HOLD
0 = eeprom OK
0 = calibration ok
0 = initial zero ok
0 = battery ok
1 = eeprom error
1 =calibration error
1 = initial zero error
1 = low battery
4
always 1
always 1
always 1
always 1
5
always 1
always 1
always 1
always 1
6
always 0
always 1
always 1
always 0
7
parity
Parity
parity
Parity
2
3
0 = stable
Byte 4 (H4)
0 = not under capacity 00 = compare disable
01 = lower limit
1 = not stable
1 = under capacity
10 = ok
0 = not at zero point 0 = not over capacity 11= upper limit
1 = at zero point
1 = over capacity
1
7.6
Byte 1 (H1)
Commands and Response
7.6.1 Parameter NCI-SCP01
Set the USER-COM-LYOUT parameter to SCP01.
54
67XXU USB/Serial Scale Service Manual
Command: W<CR> (57h 0dh), request current reading
Response
<LF>^^^^^^^^U1U2 U3U4U5<CR><LF> H1H2H3H4<CR><ETX>---over capacity
<LF>_ _ _ _ _ _ _ _ U1U2U3U4U5<CR><LF> H1H2H3H4<CR><ETX>---under capacity
<LF> - - - - - - - - U1U2 U3U4U5<CR><LF> H1H2H3H4<CR><ETX>---zero-point error
Note: U1U2 U3U4U5 is 1,2,3 or 5 bytes according to current unit: kg, lb, pcs, g, oz, lb:oz
<LF><P>W1W2W3W4W5<DP>W6 U1U2 U3 U4U5<CR><LF> H1H2H3H4 <CR><ETX>---normal data
Note: (1) The decimal point position is determined by CONFG-PRIM.D
(2) If current unit is "lb:oz", the format will be similar with following:
<LF><P>W1W2W3lb<SP>W4W5<DP>W6oz<CR><LF> H1H2H3H4 <CR><ETX>
Command: S<CR> (53h 0dh), request current status
Response
<LF> H1H2H3 H4<CR><ETX>
Command: Z<CR> (5ah 0dh)
Response
Zero function is activated (simulate ZERO key) and it returns to current scale status.
<LF> H1H2H3H4<CR><ETX>
If ZERO function cannot be activated, it will return to current scale status.
Command: T<CR> (54h 0dh)
Response
TARE function is activated (simulate TARE key), and then returns scale status.
<LF> H1H2H3H4<CR><ETX>
If TARE function cannot be activated, it will return to current scale status.
67XXU USB/Serial Scale Service Manual
55
Command: U<CR> (55h 0dh)
Response
Changes units of measure (simulate UNIT key) and return scale status with new units.
The new measure unit should be allowed to use
<LF> U1U2U3U4U5<CR><LF> H1H2H3H4<CR><ETX>
Command: L<CR> (4ch 0dh)
Response
If Hold function can be activated, it will enable/disable hold function (simulate HOLD key) and returns scale status.
<LF> H1H2H3H4<CR><ETX>
Command: X<CR> (58h 0dh)
Response
Power off the scale. Same as pressing the ON/OFF key to turn off the scale.
Command: all others
Response
Unrecognized command
<LF>? <CR><ETX>
Table 7.3 Summary of Command and Response:
Command
ASCII
HEX
W<CR>
57 0d
Read scale weight:
<LF>^^^^^^^^U1U2U3U4U5<CR><LF> H1H2H3H4<CR><ETX>---over capacity
<LF>________U1U2U3U4U5<CR><LF> H1H2H3H4<CR><ETX>---under capacity
<LF>-------- U1U2 U3U4U5<CR><LF> H1H2H3H4<CR><ETX>---zero-point error
<LF><P>W1W2W3W4W5<DP>W6U1U2U3U4U5<CR><LF>H1H2H3H4<CR><ETX>---normal data
S<CR>
53 0d
<LF>H1H2H3H4<CR><ETX>; read scale status
Z<CR>
5a 0d
<LF>H1H2H3H4<CR><ETX>; simulate ZERO key
T<CR>
54 0d
<LF>H1H2H3H4<CR><ETX>; simulate TARE key
U<CR>
55 0d
<LF> U1U2U3U4U5<CR><LF>H1H2H3H4<CR><ETX>; simulate UNIT key
L<CR>
4c 0d
<LF>H1H2H3H4<CR><ETX>; simulate HOLD key
X<CR>
58 0d
power off the scale, simulate OFF key
others
56
Response
<LF>? <CR><ETX>
67XXU USB/Serial Scale Service Manual
7.6.2 Parameter ECR-SCP02
Set the USER-COM-LYOUT parameter to SCP02.
Command: W<CR> (57h 0dh), request current reading
Response
<LF>^^^^^^^^U1U2 U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>---over capacity
<LF>_ _ _ _ _ _ _ _ U1U2U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>---under capacity
<LF> - - - - - - - - U1U2 U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>---zero-point error
Note: U1U2 U3U4U5 is 1,2,3 or 5 bytes according to current unit: kg, lb, pcs, g, oz, lb:oz
<LF><P>W1W2W3W4W5<DP>W6 U1U2 U3 U4U5<CR><LF> S H1H2H3H4 <CR><ETX>---normal data
Note: (1) The decimal point position is determined by CONFG-PRIM.D
(2) If current unit is "lb:oz", the format will be similar with following:
<LF><P>W1W2W3lb<SP>W4W5<DP>W6oz<CR><LF> S H1H2H3H4 <CR><ETX>
Command: S<CR> (53h 0dh), request current status
Response
<LF> S H1H2H3 H4<CR><ETX>
Command: Z<CR> (5ah 0dh)
Response
Zero function is activated (simulate ZERO key) and it returns to current scale status.
<LF> S H1H2H3H4<CR><ETX>
If ZERO function cannot be activated, it will return to current scale status.
67XXU USB/Serial Scale Service Manual
57
Command: U<CR> (55h 0dh)
Response
Changes units of measure (simulate UNIT key) and return scale status with new units.
The new measure unit should be allowed to use
<LF> U1U2U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>
Command: u<CR> (75h 0dh)
Response
Returns current units-of-measure as a single numeric character.
<LF>x<CR><ETX>
x=
1 = grams
2 = kilograms
3 = ounces
4 = pounds
5 = pounds - ounces
Command: A<CR> (41h 0dh)
Response
Returns scale OPOS capabilities as a string of five flag characters.
<LF>vwxyz<CR><ETX>
v = T - scale has a weight display (CapDisplay)
v = F - scale does not have a weight display
w = T -scale has a text display (CapDisplayText)
w = F -scale does not have a text display
x = T -scale can calculate unit price (CapPriceCalculating)
x = F -scale cannot calculate unit price
y = T -scale allows setting tare value (CapTareWeight)
y = F -scale does not allow setting tare value
z = T -scale may be zeroed (CapZeroScale)
z = F -scale cannot be zeroed
Command: m<CR> (6dh 0dh)
Response
Returns current maximum weight supported by the scale as a string value,
without decimal point and in the currently enabled unit of measure.
<LF>XX<CR><ETX>
58
67XXU USB/Serial Scale Service Manual
Command: <ENQ><CR> (05h 0dh)
Response
Depends on the scale and protocol.
<LF>OPOS<CR><ETX>
OPOS - enabled scale
Command: all others
Response
Unrecognized command
<LF>? <CR><ETX>
Table 7.4 Summary of Command and Response:
Command
Response
ASCII
HEX
W<CR>
57 0d
Read scale weight:
<LF>^^^^^^^^U1U2U3U4U5<CR><LF>S H1H2H3H4<CR><ETX>---over capacity
<LF>________U1U2U3U4U5<CR><LF>S H1H2H3H4<CR><ETX>---under capacity
<LF>-------- U1U2 U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>---zero-point error
<LF><P>W1W2W3W4W5<DP>W6U1U2U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>---normal data
S<CR>
53 0d
<LF> S H1H2H3H4<CR><ETX>; read scale status
Z<CR>
5a 0d
<LF> S H1H2H3H4<CR><ETX>; simulate ZERO key
U<CR>
55 0d
<LF>U1U2U3U4U5<CR><LF> S H1H2H3H4<CR><ETX>; simulate UNIT key
u<CR>
75 0d
<LF> x<CR><ETX>
A<CR>
41 0d
<LF>vwxyz<CR><ETX>
m<CR>
6d 0d
<LF>xx<CR><ETX>
<ENQ><CR>
05 0d
<LF>OPOS<CR><ETX>
L<CR>
4c 0d
<LF>H1H2H3H4<CR><ETX>; simulate HOLD key
X<CR>
58 0d
Power off the scale, simulate OFF key
others
<LF>? <CR><ETX>
67XXU USB/Serial Scale Service Manual
59
7.6.3 Parameter 8213-SCP03
Set the USER-COM-LYOUT parameter to SCP03.
Command: W (57h), request current reading
Response
<STX>W1W2<dp>W3W4W5 <CR>---normal data
Note: (1) The decimal point position is determined by CONFG-PRIM.D
(2) If current unit is "lb:oz", the format will be similar with following:
<STX>W1W2W3lbW4W5<dp>W6oz<CR>
Command: Z (5ah)
Response
Zero function is activated (simulate ZERO key) and it returns to current scale status.
<STX>?[status]<CR>
If ZERO function cannot be activated, it will return to current scale status.
Table 7.5 Status Bits
Bit
0
Status
0 = not in motion
1 = in motion
1
0 = not over capacity
1 = over capacity
2
0 = not under zero (positive polarity)
1 = under zero (negative polarity)
3
0 = inside zero capture range
1 = outside zero capture range
4
0 = not center of zero
1 = center of zero
60
5
always 1
6
always 1
7
parity
67XXU USB/Serial Scale Service Manual
Command: H (48h)
Response
Send high resolution weight dat (x10)
<STX>W1W2<dp>W3W4W5 <CR>---normal data
Note: (1) The decimal point position is determined by CONFG-PRIM.D
(2) If current unit is "lb:oz", the format will be similar with following:
<STX>W1W2W3lbW4W5W6<dp>W7oz<CR>
Command: A (41h)
Response
Scale initiates a test of RAM, ROM and NOVRAM. Places the result into confidence
test status byte for future interrogation by the host. It also returns acknowledgement.
<STX>?<CR>
Command: B (42h)
Response
Send confidence test result status byte of previously performed test (Command A).
<STX>[confidence]<CR>
Bit
Confidence
0
always 0
1
0= NOVROM Test Pass
1= NOVROM Test Fail
2
always 0
3
0= RAM Test Pass
1= RAM Test Fail
4
0= ROM Test Pass
1= ROM Test Fail
5
always 0
6
0= New Status Read
1= New Status Available
7
parity
Command: E (45h)
Response
Scale is placed in echo mode. All subsequent characters (except F) are not treated
as commands. These characters are echoed back to the host.
<STX>E<CR>
67XXU USB/Serial Scale Service Manual
61
Command: F (46h)
Response
Scale is taken out of echo mode. All subsequent characters are commands.
<STX>F<CR>
Command: all others
Response
Unrecognized command
<STX>?[status]<CR>
Table 7.6 Summary of Command and Response:
Command
ASCII
HEX
W
57
Read scale weight:
<STX>W1W2W3W4<DP>W5U1U2U3U4U5<CR>---normal data
Z
5a
<STX>?[status]<CR>
H
48
1. normal data
<STX>W1W2<dp>W3W4W5W6<CR> -- weight data (x10)
2. if current weight is invalid
<STX>?<Status Byte><CR>
A
41
<STX>?<CR>
B
42
<STX>[confidence]<CR?>
E
45
<STX>E<CR>
F
46
<STX>F<CR>
others
62
Response
<STX>?[status]<CR>
67XXU USB/Serial Scale Service Manual
7.6.4 Parameter Multi
Set the USER-COM-LYOUT parameter to mutli.
Output string frame
Command: W<CR> (57h 0dh), request current reading
<LF><Prompt><p>W1W2W3W4W5<DP>W6 U1U2 U3 U4U5<CR>
Line number and content are determined by setting of USER-OUT-xxxx
<LF><Prompt>H1H2H3H4<CR>
USER-OUT-STATUS is set to YES
C<CR>
USER-OUT1/2-LINE is set to LINE1/2/3/4
----The number of lank lines is determined by USER-OUT-LINE setting
<LF>
(1) The decimal point position is determined by CONFG-PRIM.D
(2) The unit position and bytes are determined by which current unit is used
(3) The details of <Prompt> refer to the content in User submenu
(4) In HOLD mode, if ADC conversion speed is set to high speed (80Hz) and USER-COMLYOUT is set to MULTI, the output from COM may be slower than the data processed by the
indicator. For "real time" data, select fewer output contents and set a higher baud rate for
C<CR> --- USER-OUT-LINE is set to LINE1/2/3/4
<LF> -----The number of blank lines is determined by USER-OUT1/2-LINE setting
<ETX>
--- Last byte of string frame
67XXU USB/Serial Scale Service Manual
63
Example Layouts
When USER-OUT-xxxx is set to YES
Weighing Mode:
SCALE ID:
123456
GROSS:
123lb 4.56oz
TARE:
11lb 2.22oz
NET:
112lb 2.34oz
A/D CODE:
1234567
VOLTAGE:
5.7V
STATUS:
bpq2
Counting Mode:
64
SCALE ID:
123456
GROSS:
1234.55kg
TARE:
12.15kg
NET:
1222.40kg
QUANTITY:
24448pcs
PIECE WT:
0.05kg
A/D CODE:
1234345
VOLTAGE:
5.7V
STATUS:
bpq2
67XXU USB/Serial Scale Service Manual
7.6.5 Parameter EH-SCP (PS-60)
Set the USER-COM-LYOUT parameter to eh-scp
This protocol is compatible with Toledo PS60 protocol. The baud rate and data format
is set by User menu.
Output Status Bit Meaning
Table 7.7 Status Bits
Bit
0
Status
0 = not in motion
1 = in motion
1
0 = not over capacity
1 = over capacity
2
0 = not under zero (positive polarity)
1 = under zero (negative polarity)
3
0 = inside zero capture range
1 = outside zero capture range
4
0 = not center of zero
1 = center of zero
5
always 1
6
always 1
7
parity
Summary of Command and Response
Command
ASCII
HEX
W
57
Response
Read scale weight:
<STX>W1W2<DP>W3W4W5<CR>---normal data
<STX>?[status]<CR>--if current weight is invalid
S
53
Read scale status:
<STX>?[status]<CR>
Z
5a
Simulate ZERO key:
<STX>?[status]<CR>
T
54
Simulate TARE key:
<STX>?[status]<CR>
X
58
Simulate OFF key:
power off the scale
others
Unknown commands:
<STX>?[status]<CR>
67XXU USB/Serial Scale Service Manual
65
7.6.6 Parameter IBM
Set the USER-COM-LYOUT parameter to ibm.
Command: <US> W (1Fh 57h), request current reading
Response
<STX>W1W2<dp>W3W4W5 <CR>---normal data
Note: (1) The decimal point position is determined by CONFG-PRIM.D
(2) If current unit is "lb:oz", the format will be similar with following:
<STX>W1W2W3lbW4W5<dp>W6oz<CR>
Command: <US> Z (1Fh 5ah)
Response
Zero function is activated (simulate ZERO key) and it returns to current scale status.
<STX>?[status]<CR>
If ZERO function cannot be activated, it will return to current scale status.
Table 7.8 Status Bits
Bit
0
Status
0 = not in motion
1 = in motion
1
0 = not over capacity
1 = over capacity
2
0 = not under zero (positive polarity)
1 = under zero (negative polarity)
3
0 = inside zero capture range
1 = outside zero capture range
4
0 = not center of zero
1 = center of zero
66
5
always 1
6
always 1
7
parity
67XXU USB/Serial Scale Service Manual
Command: <US> H (1Fh 48h)
Response
Send high resolution weight dat (x10)
<STX>W1W2<dp>W3W4W5W6 <CR>---normal data
Note: (1) The decimal point position is determined by CONFG-PRIM.D
(2) If current unit is "lb:oz", the format will be similar with following:
<STX>W1W2W3lbW4W5W6<dp>W7oz<CR>
Command: <US> A (1Fh 41h)
Response
Scale initiates a test of RAM, ROM and NOVRAM. Places the result into confidence
test status byte for future interrogation by the host. It also returns acknowledgement.
<STX>?<CR>
Command: <US> B (1Fh 42h)
Response
Send confidence test result status byte of previously performed test.
<STX>[confidence]<CR>
Bit
Confidence
0
always 0
1
0= NOVROM Test Pass
1= NOVROM Test Fail
2
always 0
3
0= RAM Test Pass
1= RAM Test Fail
4
0= ROM Test Pass
1= ROM Test Fail
5
always 0
6
0= New Status Read
1= New Status Available
7
parity
Command: <US> E (1Fh 45h)
Response
Scale is placed in echo mode. All subsequent characters (except F) are not treated
as commands. These characters are echoed back to the host.
<STX>E<CR>
67XXU USB/Serial Scale Service Manual
67
Command: <US> F (1Fh 46h)
Response
Scale is taken out of echo mode. All subsequent characters are commands.
<STX>F<CR>
Command: all others
Response
Unrecognized command
<STX>?[status]<CR>
Table 7.9 Summary of Command and Response:
Command
ASCII
HEX
<US> W
1F 57
1. normal data
<STX>W1W2<dp>W3W4W5<CR>
2. if current weight is invalid
<STX>?<Status Byte><CR>
<US> Z
1F 5a
<STX>?[status]<CR>
<US> H
1F 48
1. normal data
<STX>W1W2<dp>W3W4W5W6<CR> -- weight data (x10)
2. if current weight is invalid
<STX>?<Status Byte><CR>
<US> A
1F 41
<STX>?<CR>
<US> B
1F 42
<STX>[confidence]<CR?>
<US> E
1F 45
<STX>E<CR>
<US> F
1F 46
<STX>F<CR>
others
68
Response
<STX>?[status]<CR>
67XXU USB/Serial Scale Service Manual
8
Legal for Trade
The 67XXU Model must be configured to meet regulations mandated by local weights
and measures authorities.
8.1
Physical Seal
The configuration/calibration push button is used to protect the scale from being
configured or calibrated under legal for trade conditions. When set to legal for trade and
sealed with a lead seal, the scale can only be configured and calibrated by authorized
personnel.
The push button is located under the center screw on the underside of the scale.
Remove the center screw. Press the button with a non-metallic object or a #0 phillips
screwdriver.
CAUTION!
Do not use a flat blade screwdriver or other small metallic object as this could
damage the scale!
.
Push Button
Figure 8.1 Physical Seal Location
67XXU USB/Serial Scale Service Manual
69
8.2
Audit Trail Parameters
Two separate incrementing, non-resetable audit trail parameters are used to indicate
changes to various parameters or calibration.
8.2.1 View Configuration Counter
1.
Press and hold the [HOLD] + [ON/OFF] key for 3 seconds. CONFG is
displayed.
2.
Press the [TARE] key to view the configuration counter.
2a.
The display will briefly show the number of times the configuration has been
changed and will save up to 9999. This counter can't be modified or erased. It
counts from 0000 to 9999. When 9999 is reached, the counter starts over at
0000. The display will then show whether the configuration switch is on
(cf.on) or (cf.off) off.
To Exit:
1.
Press the [ON/OFF] key twice. Exit? is displayed.
2.
Press the [TARE] key to return to the working mode.
8.2.2 View Calibration Counter
1.
Press and hold the [HOLD] + [ON/OFF] key for 3 seconds. CONFG is
displayed.
2.
Use the [HOLD] key to select the CAL menu.
3.
Press the [TARE] key to enter the calibration mode.
3a.
After entering this mode, the number of calibrations will be shown first. This
number will be increment one digit after every time a calibration has been
performed and saved. This counter can't be modified or erased. It counts from
0000 to 9999, when 9999 is reached, the counter starts over at 0000.
4.
After the counter number was displayed, it will show "Ca.OFF" or "CAL-ON"
which depends on whether the sealed calibration switch is OFF or ON. If the
switch is OFF, the following steps can be done, but the result will not be
saved.
To Exit:
70
1.
Press the [ON/OFF] key twice. Exit? is displayed.
2.
Press the [TARE] key to return to the working mode.
67XXU USB/Serial Scale Service Manual
9
Troubleshooting
This chapter gives explanations on commonly seen errors, display characters and
display symbols.
9.1
Display Characters
ASCII
LCD/LED
ASCII
LCD/LED
ASCII
0
A
N
1
B
O
2
C
P
3
D
Q
4
E
R
5
F
S
6
G
T
7
H
U
8
I
V
9
J
W
K
X
L
Y
M
Z
67XXU USB/Serial Scale Service Manual
LCD/LED
71
9.2
Display Symbols
Symbol
72
Description
0----
Zero is over the setting range
0_____
Zero point is below the setting range
Ad----
Signal to ADC is over maximum range
Ad____
Signal to ADC is below minimum range
----
Weight is over upper limitation or display data is over limitation
____
Weight is below lower limitation
EEP.E1
CONFG or CAL parameters are not correctly set
EEP.E2
USER parameter is not correctly set
Lo.bAt
Battery voltage is lower than setting
CAP.- - -
Next displaying content is capacity
CAP.ER
Parameters about Capacity is not correct
CAL.Px
Calibration on point (x)
CAL.OFF
Calibration seal switch is on OFF position
CAL.ON
Calibration seal switch is on ON position
CAL.Er
Calibration error, maybe input data or loaded weight is incorrect, unstable, non-linear
CA.End
End calibration
OFF
Power OFF the indicator
STB.ER
Unstable time is larger than setting of USER-OTHER-NLD.RNG
PR.TAR
Preset TARE weight
COMP
Input COMPARE data mode
HIGH
Input HIGH limitation data of Comparison
LOW
Input LOW limitation data of Comparison
SPL.Lo
Sample load weight of low point.
SPL.HI
Sample load weight of high point.
67XXU USB/Serial Scale Service Manual
Symbol
9.3
Description
SPL.PW
Sample goods weight to calculate piece weight
IN.PCS
Input number of pieces being counted
UNT.KG
Unit kg is selected
UNT.LB
Unit lb is selected
PWT.ER
Piece weight error, sample too small (<0.5d)
Error Messages and Troubleshooting
Symptom
Ad---
Probable Cause
Remedy
Ad___
Loadcell wires to indicator are incorrectly
Make sure wires are ok and correctly connected.
connected, shorted, opened, ADC or loadcell(s) Replace loadcell or ADC chip, Service required.
are damaged.
0----
Weight reading exceeds Power On Zero limit.
Make sure scale platform is empty. Perform zero
calibration.
0____
Weight reading below Power On Zero limit.
Install platform on scale. Perform zero calibration.
----
Weight reading exceeds Overload limit or the
Reduce load on scale until weight value can be
weight value cannot be displayed in the current displayed. Use a more appropriate unit of measure.
unit of measure because it exceeds 6 digits.
Re-set some parameters of CONFG or USER.
____
Weight reading below Under load limit.
Install platform on scale.Perform zero calibration.
EEP.E1
CONFG or CAL parameters are not correctly
set.
Re-set items in CONFG, do calibration.
EEP.E2
USER parameter is not correctly set.
Re-set items in USER.
CAP.ER
Capacity parameters are not correct.
Set PRIM.N/PRIM.D/SECND.n to correct number,
make sure capacity not more than 6 digit.
CAL.Er
Calibration error. Input data or loaded weight is Input correct data, load correct weight onto
too small, too big, unstable, non-linear.
platform, Service required.
PWT.ER
Piece weight is error, it's too small (<0.5d), The Use a greater weight for the sample.
weight on the platform is too small to define a
valid reference weight.
67XXU USB/Serial Scale Service Manual
73
Symptom
74
Probable Cause
Remedy
PCT.ER
Unit-Percentage -Weight is error, it's too small
(the weight of 1%, 0.1%, or 0.01%-determined
by CONFG-FUNC-PERCNT is less than 0.5d).
Use more weight for the sample.
STB.ER
USER-HOLD-STB.TIM is too short, USERHOLD-HLD.RG is too small, other failure.
Set USER-HOLD-STB.TIM longer, or set USERHOLD-HLD.RG bigger. Service required.
Will not turn on.
Power cord not plugged in or properly
connected. Power outlet not supplying
electricity. Battery discharged. Other failure.
Check power cord connections. Make sure power
cord is plugged into the power outlet. Check power
source. Replace batteries. Service required.
Cannot zero the display Load on scale exceeds allowable limits. Load
or will not zero when
on scale is not stable. Load cell damage.
turned on.
Remove load on scale. Wait for load to become
stable. Service required.
Cannot display weight in Unit not set to enable or d≥5oz, when unit is
desired weighing unit.
lb:oz.
Enable unit in CONFG-UNITS.
67XXU USB/Serial Scale Service Manual
Brecknell USA
1000 Armstrong Dr.
Fairmont MN 56031
Tel:507-238-8702
Fax:507-238-8271
Email: [email protected]
http://www.brecknellscales.com
Brecknell UK
Foundry Lane,
Smethwick, West Midlands,
England B66 2LP
Tel:+44 (0) 8452 46 6717
Fax:+44 (0) 8452 46 6718
Email:
[email protected]
http://www.brecknellscales.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement